NIT No- 01/2026-27, Package No- 3B Long Term Output & Performance Based Road Assets Maintenance Work for the Roads under Road Division Motihari. (OPRMC) PHASE-III, Package-3B/Motihari

Ordinary Maintenance Services in the following Roads (with chainage): -

Item No.

In words

Repairs to shoulders /Construction of Earthen shoulders on both sides of the carriageway wherever required to bring the service level (with 3% camber) (i) Earthen Shoulder: (a) High Shoulder (b) Low shoulder (ii) Hard Shoulder: (a) Paved Shoulder/ Granular (b) Footpath

Plantation in medians and islands not maintained by other agencies.

Pruning of trees to get 5.5 m height above the pavement.

Repairs and cleaning to Cross Drainage Works including Culverts and side drains (outside the area of Municipal Corporation and Nagar Parishad) to specified service levels by taking up required items ensuring to minimum quantity as per Section 5D of Technical Specification.

Providing Road safety and informatory items complete as per IRC:67/latest code specifications such as;

Providing and fixing new mandatory, cautionary and informatory Retro Reflectorized signage, ensuring minimum quantity as per Section 5D of Technical Specification.

Maintenance of existing signages ensuring minimum quantity as per Section 5D of Technical Specification.

Fixing new and maintenance of existing KM stones as per MORTH Specifications ensuring minimum quantity as per Section 5D of Technical Specification.

Fixing New & Maintenance of existing Guard stones/ Guide post as per MORTH Specifications ensuring minimum quantity as per Section 5D of Technical Specification.

Fixing New and Maintenance of existing Object Hazard Marker at the opening ends of culverts and bridges or at any other points, delineators. median markers and bollards (spring post) as required, as per MORTH Specifications ensuring minimum quantity as per Section 5D of Technical Specification.

Providing New and Maintenance of existing Rumble strips/ speed breaker or any traffic calming measures on minor/major roads as per MORTH Specifications ensuring minimum quantity as per Section 5D of Technical Specification.

Providing new and maintenance of existing Road marking as per IRC: 35/latest code-

Hot Applied Thermoplastic compound 2.5mm thick including reflectorising glass beads with (Clause 803-Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface-Providing & laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @250gm/sqm area, thickness of 2.5mm is exclusive of surface applied glass beads as per IRC:35 latest code. The finished surface to be level, uniform & free from streaks & holes). i. Centre line, lane line marking as per IRC: 35 latest code or as per existing road markings. ii. Edge line marking for all lanes/ roads as per IRC:35 latest code or as per existing road markings. Ensuring minimum quantity as per Section 5D of Technical Specification.

Reflective Raised Pavement Marker with Shank(Road Stud) (SOR. No.-8.35b)Reflective Raised Pavement Marker with Shank (Cat Eye/Road Stud) Supplying and fixing of raised pavement marker with made of aluminium alloy or plastic body moulded from ASA (Acrylic Styrene Acrylonitrite) or HIPS (High Impact Polystyrene) or Acrylonitrite Butadiene Styrene (ABS) or any other suitable material approved by the Engineer. The marker shall support a load of 13,635 kg tested in accordance with ASTM D4280. The reflective panels shall consist of number of lenses containing single or dual prismatic cubes capable of providing total internal reflection of the light entering the lens face.Lenses shall be moulded of methyl methecrylate conforming to ASTM D788 of equivalent.The slop or retro-reflecting surface shall preferably be 35+/-5 degree to base and the area of each retro- reflecting surface shall not be less than 13.00 sq.cm the marker height shall not be less than 10 mm and shall not exceed 20 mm & width shall not exceed 130 mm. The base of the marker shall be flat within 1.3 mm,......intimation from the Engineer, at his own cost.

Repair and Painting of road side assets including painting of trees & poles on formation width; (a) Repair of dividers, road kerbs, islands, parapets and RCC/Brick drains (b) Painting of Trees and Poles Painting of road divider, island, parapets, kerbs etc. ensuring minimum quantity as per Section 5D of Technical Specification.

Any additional activities the Bidder considers necessary to achieve the Service Level Objective.

Item No.

In words

Tack Coat (Clause-503) Tack Coat on Bituminous surfaces- (SOR. No.-5.02(i))( Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom)

BC 30mm (Clause 507) - Bituminous concrete Grading- II- (SOR. No.-5.05B)( Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @5.4 percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment , rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORT&H specification clause no. 507 complete in all respects.)

Maintenance of Shoulders as per MORTH Specification 305. (SOR. No.-3.16) (Construction of Embankment with approved material obtained from Borrow pits with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of Table 300-2.)

Thermoplastic Edge Line Marking, Zebra,Bar Marking. (SOR. No.-8.13)(Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.))

Painting of Parapets, Kerbs, Islands, Dividers. (SOR. No.-8.13)Painting Two Coats on New Concrete Surfaces (Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces)

Reflective Raised Pavement Marker with Shank(Road Stud) (SOR. No.-8.35b)Reflective Raised Pavement Marker with Shank (Cat Eye/Road Stud) Supplying and fixing of raised pavement marker with made of aluminium alloy or plastic body moulded from ASA (Acrylic Styrene Acrylonitrite) or HIPS (High Impact Polystyrene) or Acrylonitrite Butadiene Styrene (ABS) or any other suitable material approved by the Engineer. The marker shall support a load of 13,635 kg tested in accordance with ASTM D4280. The reflective panels shall consist of number of lenses containing single or dual prismatic cubes capable of providing total internal reflection of the light entering the lens face.Lenses shall be moulded of methyl methecrylate conforming to ASTM D788 of equivalent.The slop or retro-reflecting surface shall preferably be 35+/-5 degree to base and the area of each retro- reflecting surface shall not be less than 13.00 sq.cm the marker height shall not be less than 10 mm and shall not exceed 20 mm & width shall not exceed 130 mm. The base of the marker shall be flat within 1.3 mm,......intimation from the Engineer, at his own cost.

Single lane (Carriage way width < 3.75m) (30 mm thick BC). Rate shall be quoted assuming per kilometre carpet area as 3750m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).

Intermediate lane (30 mm thick BC) (Carriage way width > 3.75 and < 7.0 m). Rate shall be quoted assuming per kilometre carpet area as 5500 m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).

Providing 40mm thick BC for Periodical Maintenance to Double and Multi lanes including profile correction (Carriage width ≥ 7.0m) with the following items of work to obtain the required service level.

Tack Coat (Clause-503) Tack Coat on Bituminous surfaces- (SOR. No.-5.02(i))( Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom)

BC 30mm (Clause 507) - Bituminous concrete Grading- II- (SOR. No.-5.05B)( Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @5.4 percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment , rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORT&H specification clause no. 507 complete in all respects.)

Providing shoulder width 2.5m using with 3% camber to the required the service level for low shoulders as per MORTH Specification Clause 305. (SOR. No.-3.16) (Construction of Embankment with approved material obtained from Borrow pits with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of Table 300-2.)

Providing centre line and lane line marking (SOR. No.-8.13)(Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.)) as per IRC:35/latest code.

Providing Continuous edge line marking (SOR. No.-8.13)(Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.)) as per IRC:35/latest code.

Reflective Raised Pavement Marker with Shank(Road Stud) (SOR. No.-8.35b)Reflective Raised Pavement Marker with Shank (Cat Eye/Road Stud) Supplying and fixing of raised pavement marker with made of aluminium alloy or plastic body moulded from ASA (Acrylic Styrene Acrylonitrite) or HIPS (High Impact Polystyrene) or Acrylonitrite Butadiene Styrene (ABS) or any other suitable material approved by the Engineer. The marker shall support a load of 13,635 kg tested in accordance with ASTM D4280. The reflective panels shall consist of number of lenses containing single or dual prismatic cubes capable of providing total internal reflection of the light entering the lens face.Lenses shall be moulded of methyl methecrylate conforming to ASTM D788 of equivalent.The slop or retro-reflecting surface shall preferably be 35+/-5 degree to base and the area of each retro- reflecting surface shall not be less than 13.00 sq.cm the marker height shall not be less than 10 mm and shall not exceed 20 mm & width shall not exceed 130 mm. The base of the marker shall be flat within 1.3 mm,......intimation from the Engineer, at his own cost.

Providing repairs & painting to median & kerbs, islands, dividers. (SOR. No.-8.08)Painting Two Coats on New Concrete Surfaces (Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces)

Maintenance of shoulders as per MORTH Specifications- 305. (SOR. No.-3.16) (Construction of Embankment with approved material obtained from Borrow pits with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of Table 300-2.)

Double Lane - Rate shall be quoted assuming per kilometre carpet area as 7000m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).

Multi Lane -Rate shall be quoted assuming per kilometre carpet area as 14000m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).

Providing Periodic Maintenance to Single and Intermediate Lanes including profile correction with the following items of works to obtain the required service level.

Tack Coat (Clause-503) Tack Coat on Bituminous surfaces- (SOR. No.-5.02(i))( Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom)

BC 30mm (Clause 519) Using by bituminous concrete Grading II – (SOR. No.-5.13C(ii)) Recycling pavement by cold milling of existing bituminous layers, planning the surface after cold milling, reclaiming excavated material to the extent of 30 percent of the required quantity, hauling and stock piling the reclaimed material near the central recycling plant after carrying out necessary checks and evaluation, adding fresh material including rejuvenators as required , mixing in a hot mix plant, transporting and laying at site and compacting to the required the grade , level and the thickness, all as specified in clause 519.

Maintenance of Shoulders as per MORTH Specification 305. (SOR. No.-3.16) (Construction of Embankment with approved material obtained from Borrow pits with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of Table 300-2.)

Thermoplastic Edge Line Marking, Zebra,Bar Marking. (SOR. No.-8.13)(Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.))

Painting of Parapets, Kerbs, Islands, Dividers. (SOR. No.-8.08)Painting Two Coats on New Concrete Surfaces (Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces)

Reflective Raised Pavement Marker with Shank(Road Stud) (SOR. No.-8.35b)Reflective Raised Pavement Marker with Shank (Cat Eye/Road Stud) Supplying and fixing of raised pavement marker with made of aluminium alloy or plastic body moulded from ASA (Acrylic Styrene Acrylonitrite) or HIPS (High Impact Polystyrene) or Acrylonitrite Butadiene Styrene (ABS) or any other suitable material approved by the Engineer. The marker shall support a load of 13,635 kg tested in accordance with ASTM D4280. The reflective panels shall consist of number of lenses containing single or dual prismatic cubes capable of providing total internal reflection of the light entering the lens face.Lenses shall be moulded of methyl methecrylate conforming to ASTM D788 of equivalent.The slop or retro-reflecting surface shall preferably be 35+/-5 degree to base and the area of each retro- reflecting surface shall not be less than 13.00 sq.cm the marker height shall not be less than 10 mm and shall not exceed 20 mm & width shall not exceed 130 mm. The base of the marker shall be flat within 1.3 mm,......intimation from the Engineer, at his own cost.

Single lane (Carriage way width < 3.75m) (30 mm thick BC). Rate shall be quoted assuming per kilometre carpet area as 3750m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).

Intermediate lane (30 mm thick BC) (Carriage way width > 3.75 and < 7.0 m). Rate shall be quoted assuming per kilometre carpet area as 5500 m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).

Providing 40mm thick BC for Periodical Maintenance to Double and Multi lanes including profile correction (Carriage width ≥ 7.0m) with the following items of work to obtain the required service level.

Tack Coat (Clause-503) Tack Coat on Bituminous surfaces- (SOR. No.-5.02(i))( Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom)

BC 40mm (Clause 519) Using by bituminous concrete Grading II – (SOR. No.-5.13C(ii)) Recycling pavement by cold milling of existing bituminous layers, planning the surface after cold milling, reclaiming excavated material to the extent of 30 percent of the required quantity, hauling and stock piling the reclaimed material near the central recycling plant after carrying out necessary checks and evaluation, adding fresh material including rejuvenators as required , mixing in a hot mix plant, transporting and laying at site and compacting to the required the grade , level and the thickness, all as specified in clause 519.

Providing shoulder width 2.5m using with 3% camber to the required the service level for low shoulders as per MORTH Specification Clause 305. (SOR. No.-3.16) (Construction of Embankment with approved material obtained from Borrow pits with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of Table 300-2.)

Providing centre line and lane line marking ((SOR. No.-8.13)(Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.)) as per IRC:35/latest code.

Providing Continuous edge line marking (SOR. No.-8.13)(Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.)) as per IRC:35/latest code.

Reflective Raised Pavement Marker with Shank(Road Stud) (SOR. No.-8.35b)Reflective Raised Pavement Marker with Shank (Cat Eye/Road Stud) Supplying and fixing of raised pavement marker with made of aluminium alloy or plastic body moulded from ASA (Acrylic Styrene Acrylonitrite) or HIPS (High Impact Polystyrene) or Acrylonitrite Butadiene Styrene (ABS) or any other suitable material approved by the Engineer. The marker shall support a load of 13,635 kg tested in accordance with ASTM D4280. The reflective panels shall consist of number of lenses containing single or dual prismatic cubes capable of providing total internal reflection of the light entering the lens face.Lenses shall be moulded of methyl methecrylate conforming to ASTM D788 of equivalent.The slop or retro-reflecting surface shall preferably be 35+/-5 degree to base and the area of each retro- reflecting surface shall not be less than 13.00 sq.cm the marker height shall not be less than 10 mm and shall not exceed 20 mm & width shall not exceed 130 mm. The base of the marker shall be flat within 1.3 mm,......intimation from the Engineer, at his own cost.

Providing repairs & painting to median & kerbs, islands, dividers. (SOR. No.-8.08)Painting Two Coats on New Concrete Surfaces (Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces)

Maintenance of shoulders as per MORTH Specifications- 305. (SOR. No.-3.16) (Construction of Embankment with approved material obtained from Borrow pits with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of Table 300-2.)

Double Lane - Rate shall be quoted assuming per kilometre carpet area as 7000m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).

Multi Lane -Rate shall be quoted assuming per kilometre carpet area as 14000m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).

Providing Periodic Maintenance to Single and Intermediate Lanes including profile correction with the following items of works to obtain the required service level.

Tack Coat (Clause-503) - Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom

BC 30mm (Clause 518) – Providing laying and rolling of bituminous cold mix on prepared base consisting of a mixture of unheated mineral aggregate and emulsified or cutback bitumen, including mixing in a plant of suitable type and capacity, transporting, laying compacting and finishing to specified grades and levels.

Maintenance of Shoulders as per MORTH Specification 305.

Thermoplastic Edge Line Marking.

Painting of Parapets, Kerbs, Islands, Dividers.

Single lane (Carriage way width < 3.75m) (30 mm thick BC). Rate shall be quoted assuming per kilometre carpet area as 3750m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).

Intermediate lane (30 mm thick BC) (Carriage way width > 3.75 and < 7.0 m). Rate shall be quoted assuming per kilometre carpet area as 5500 m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).

Providing 40mm thick BC for Periodical Maintenance to Double and Multi lanes including profile correction (Carriage width ≥ 7.0m) with the following items of work to obtain the required service level.

Tack Coat (Clause-503) - Providing and applying Tack Coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/ granular surface cleaned with mechanical broom.

BC 30mm (Clause 518) – Providing laying and rolling of bituminous cold mix on prepared base consisting of a mixture of unheated mineral aggregate and emulsified or cutback bitumen, including mixing in a plant of suitable type and capacity, transporting, laying compacting and finishing to specified grades and levels.

Providing shoulder width 2.5m using with 3% camber to the required the service level for low shoulders as per MORTH Specification Clause 305.

Providing centre line and lane line marking (Hot Applied Thermoplastic compound 2.5 mm thick including reflect rising glass beads) as per IRC:35/latest code.

Providing Continuous edge line marking (Hot Applied Thermoplastic compound 2.5mm thick including reflect rising glass beads) as per IRC:35/latest code.

For Urban Roads as mentioned in Appendix and as per the direction of Engineer-in-Charge - Providing & fixing of reflective pavement markers Road Markers/Road Studs with micro prismatic Lense Reflector- Providing and fixing of road stud 100 x 100 mm, die-cast moulded from ASA (Acrylic Strene Acrylonitrite) High impact poly styrene or ABS (Acrylonitrile Butadiene Styrene).

Providing repairs & painting to median & kerbs, islands, dividers.

Maintenance of shoulders as per MORTH Specifications- 305.

Double Lane - Rate shall be quoted assuming per kilometre carpet area as 7000m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).

Double Lane with Paved Shoulders of width ______________.

Item No.

In words

(SOR. No.-8.13) Providing Re-Application of Thermoplastic Road Marking at the interval of minimum 2 years in Double Lane including auxiliary items-(Zebra and Bar Marking) as per the MORTH/IRC:35 latest Specifications & as per the direction of Engineer-in-charge with the following items of works to obtain the required service level

Providing centre line and lane line marking (Hot Applied Thermoplastic compound 2.5 mm thick including reflect rising glass beads) as per IRC:35/latest code.

Providing Continuous edge line marking (Hot Applied Thermoplastic compound 2.5mm thick including reflect rising glass beads) as per IRC:35/latest code.

Reflective Raised Pavement Marker with Shank(Road Stud) (SOR. No.-8.35b)Reflective Raised Pavement Marker with Shank (Cat Eye/Road Stud) Supplying and fixing of raised pavement marker with made of aluminium alloy or plastic body moulded from ASA (Acrylic Styrene Acrylonitrite) or HIPS (High Impact Polystyrene) or Acrylonitrite Butadiene Styrene (ABS) or any other suitable material approved by the Engineer. The marker shall support a load of 13,635 kg tested in accordance with ASTM D4280. The reflective panels shall consist of number of lenses containing single or dual prismatic cubes capable of providing total internal reflection of the light entering the lens face.Lenses shall be moulded of methyl methecrylate conforming to ASTM D788 of equivalent.The slop or retro-reflecting surface shall preferably be 35+/-5 degree to base and the area of each retro- reflecting surface shall not be less than 13.00 sq.cm the marker height shall not be less than 10 mm and shall not exceed 20 mm & width shall not exceed 130 mm. The base of the marker shall be flat within 1.3 mm,......intimation from the Engineer, at his own cost.

(SOR. No.-8.13) Providing Re-Application of Thermoplastic Road Marking at the interval of minimum 2 years in Multi Lanes including auxiliary items-(Zebra and Bar Marking) as per the MORTH/IRC:35 latest Specifications & as per the direction of Engineer-in-charge with the following items of works to obtain the required service level

Providing centre line and lane line marking (Hot Applied Thermoplastic compound 2.5 mm thick including reflect rising glass beads) as per IRC:35/latest code.

Providing Continuous edge line marking (Hot Applied Thermoplastic compound 2.5mm thick including reflect rising glass beads) as per IRC:35/latest code.

Reflective Raised Pavement Marker with Shank(Road Stud) (SOR. No.-8.35b)Reflective Raised Pavement Marker with Shank (Cat Eye/Road Stud) Supplying and fixing of raised pavement marker with made of aluminium alloy or plastic body moulded from ASA (Acrylic Styrene Acrylonitrite) or HIPS (High Impact Polystyrene) or Acrylonitrite Butadiene Styrene (ABS) or any other suitable material approved by the Engineer. The marker shall support a load of 13,635 kg tested in accordance with ASTM D4280. The reflective panels shall consist of number of lenses containing single or dual prismatic cubes capable of providing total internal reflection of the light entering the lens face.Lenses shall be moulded of methyl methecrylate conforming to ASTM D788 of equivalent.The slop or retro-reflecting surface shall preferably be 35+/-5 degree to base and the area of each retro- reflecting surface shall not be less than 13.00 sq.cm the marker height shall not be less than 10 mm and shall not exceed 20 mm & width shall not exceed 130 mm. The base of the marker shall be flat within 1.3 mm,......intimation from the Engineer, at his own cost.

S.O.R No.

In words

Construction of RCC railing of M30 Grade in-situ with 20 mm nominal size aggregate, true to line and grade, tolerance of vertical RCC post not to exceed 1 in 500, centre to centre spacing between vertical post not to exceed 2000 mm, leaving adequate space between vertical post for expansion, complete as per approved drawings and technical specifications.

Painting Two Coats on New Concrete Surfaces (Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces)

Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class-B Type IV retro reflective sheeting fixed cover 2 mm thick aluminium sheeting vide clause 801.3, 3mm/4mm thick aluminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing.

75 cm equilateral triangle

80 cmx60cm rectangular

60 cm circular

90 cm Octagonal

60 cm X 45cm rectangular

90 cm equilateral triangle

Type - A, "W" : Metal Beam Crash Barrier (Providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 811)

Road Delineators (Supplying and installation of MS delineators (Road way indicators, hazard markers, object markers), 80-100 cm high above ground level, painted black and white in 15 cm wide strips, fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and conforming to IRC-79 and the drawings. MS Delineator made of Mild steel with pure polyester powder coating with the minimum thickness of powder coating of not less than 40 micron for protection against corrosion. The surface should be concealed so that there should not be any exposed surface without powder coating. Alternatively,these metal guide poles can be concealed with thermoplastic body. The posts shall have fan ellipsoidal or circular design with the height of the pole shall be 800 to 900 mm above the ground with about 200 to 300 mm base which can be anchored onto ground. Mild steel Guide poles shall conform to Type XI sheeting specifications as per IRC:67 and ASTM D4956 which would ensure to obtain clear visibility of the road alignment during night time. The retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, linear removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Goverment Laboratory/Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from indian condition within 3 years of launching of product by the manufacture in abroad.Alternatively, a certificate conforming to ASTM specification (D4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally.In such a situation, the Employer/Client, if so desires could seek for a performance guarantee which would released after receipt a certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012 & proof of the same report shall be uploaded while quoting tendor.

Kilometre Stone (Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc). 5th Kilometer stone precast.

Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc. Ordinary kilometre stone (precast)

Direction and Place Identification Signs with size more than 0.9 sqm size Board.(Providing and erecting direction and place identification retro- reflectorised sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick or Aluminium composite material sheet with overall thickness of 4 mm with area exceeding 0.9 sqm fixed over back support frame of min 40 x 40 x 5 mm Angle mounted on two nos. of mild steel circular pipe 65 NB, 3.2mm thickness and 4.5m meter total height firmly fixed to the ground by means of properly designed foundation with M 25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing).The retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, linear removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Goverment Laboratory/Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from indian condition within 3 years of launching of product by the manufacture in abroad.Alternatively, a certificate conforming to ASTM specification (D4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally.In such a situation, the Employer/Client, if so desires could seek for a performance guarantee which would released after receipt a certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012 & proof of the same report shall be uploaded while quoting tendor. 7 years warranty shall be provided for retro reflection sheeting Type-IV & 10 years warranty shall be provided for retro reflective sheeting Type-XI as per Clause 6.9 of IRC 67:2012. At the end of warranty period, the sheeting shall retain atleast 80% of its retro reflectance. When totally wet, the sheeting shall show not less than 90% of the value of the desired retro reflectance. `

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.

Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing.

Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with approve grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383 as per actual Design Mix, possessing 28 days minimum compressive strength of 40( Forty) Mpa and 28 days minimum flexural strength of 4.5 (Four point five) MPa, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing

Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required a nd utilising the remaining earth locally for road work.

Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.

Plain/Reinforced cement concrete in open foundation complete as per drawing and technical specifications PCC Grade M15 using batching plant,transit mixer & manual placing

Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. RCC Grade M20 using batching plant,transit mixer & manual placing

Plain/Reinforced cement concrete in open foundation complete as per drawing and technical specifications PCC Grade M20 using batching plant,transit mixer & manual placing

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.

Providing new reflectorised strip of 15cmX 15cm on aluminium sheet as tree guard minimum 2 nos for each tree.

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of table 300-2.

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with grader in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

Providing and applying primer coat with cutback MC 30 bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means.

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom.

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 % by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects. for GradingII(19 mm nominal size)

Bituminous Concrete (Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 % of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects.)for Grading II ( 10 mm nominal size)

Solar Powered Road Marker (Solar Stud) Supplying and fixing of Solar Raised Pavement Markers made of polycarbonate moulded body with circular shape, solar powered, LED self illumination in active mode, 360 degree illumination and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face in passive mode. The marker shall support a load of 13,635 kg tested in accordance to ASTM D 4280. The marker should be resistant to dust and water ingress according to IP 65 standards and should withstand temperatures in the range of 0 C to 70 C. Color of lighting could be provided in red or yellow (amber) as per requirement and typical frequency of blinking in 1 Hz. There should be current losses of less than 20 microamperes at 2.4 V in sleepcharging mode to enhace the life of the marker and a full charge should provide for a minimum autonomy of 50 hours. The height, width and length of the marker shall not be less than 10mm x 100 mm x 100 mm. Also, the surface diameter of the marker shall not be less than 100 mm respectively. The weight of the marker shall not exceed 0.5 Kilograms. It shall have super bright LED's so as to provide long visibility from a distance of more than 800 m. Its life shall not be less than 3 years. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive and complete as directed by the engineer

Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2. of MoRT&H specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and Technical Specification.

Back filling behind abutment, wing wall and return wall complete as per drawing and Technical Specification With sandy material

Drainage spouts complete as per Drawing and Technical Specifications.

Providing & fixing 20 mm thick compressible fibre board in expansion joint complete as per drawing & Technical Specification.

Providing weep holes in Brick masonary/ plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V:20H towards drawing face. Complete as per drawing and Technical specifications.

Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications

Reinforced cement concrete approach slab including reinforcement and formwork complete as per drawing and Technical specification

Providing and laying Flooring complete as per drawing and Technical specifications laid over cement concrete bedding. ( Rubble stone laid in cement mortar 1:3)

Providing and laying boulders apron on river bed for protection against scour with stone boulders weighing not less than 40 kg each complete as per drawing and Technical specification.

Supplying and laying of 80 mm thick Paver Block M40 grade

Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. By Mechanical means. ( Depth upto 3 m )

Plain/ Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications . PCC Grade M15 using batching plant , transit mixer & manual placing

Plain/ Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications . RCC Grade M20 using batching plant , transit mixer & manual placing.

Supplying ,Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications.

Traffic Cone (Provision of red fluorescent with white reflective sleeve traffic cone made of low density polyethylene (LDPE) material with a square base of 390 x 390 x 35 mm and a height of 770 mm, 4 kg in weight, placed at 1.5 m interval, all as per BS 873)

Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metresRCC M20 and above

Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres Brick/Tile work (Cement Mortar)

Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2.

Laying Reinforcement Cement Concrete Pipe NP4 (1000mm Dia.) on First Class Bedding in Single Row.

Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. RCC Grade M30 using batching plant,transit mixer & manual placing

Providing and laying 25 mm thick mastic asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-39, prepared by using mastic cooker and laid to required level and slope after cleaning the surface, including providing antiskid surface with bitumen precoated fine grained hard stone chipping of 13.2 mm nominal size at the rate of 0.005 cum per 10sqm and at an approximate spacing of 10cm center to center in both directions, pressed into surface when the temperature of surfaces is not less tha 1000c, protruding 1mm to 4mm over mastic surface, all complete as per clause 516.

Amount ₹ INR