Construction of Government Senior Secondary School at Nagheta, Tehsil Paonta Sahib, District Sirmour ( HP ) ( SH- Construction of building portion , providing water supply, sanitary installation, construction of septic tank with soak pit, rain wat

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains in all heights and depths in all kinds of soil, including saturated soil comprising of pick work,jumper work and blasting work both in soft and hard rock with chiesling and wedging out of rock (where blasting is prohabited) and their intermediate classification of soil including dewatering whereever required,settling out to required lines,levels as shown on the drawing and directed by the Engineer in charge at site according to the HP.PWD specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (to be arranged by the contractor) including payment of prescribed dumping charges of M.C. if levilled any to the satisfaction of the Engineer in charge through all modes of transporation including head load animal load or mechanical means alongwith its levelling, fine dressing and with all kinds of labour, mechineries, tools, equipment and safety measures and incidental necessary to complete the work by mechanical means and labour (if required). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transporation and used/removed as per the satisfaction of the Engineer in charge. any loss to the public and private properity during the course of execution and disposal of servicable and unservicable materials shall be the absolute responsiblity of the contractor and shall have to be duly compensated by him in all respects including all incidential charges and as directed by the Engineer in Charge:- All kinds of soil.

Supplying & filling in plinth with sand under floors including watering, ramming, consolidating & dressing complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Filling available excavated earth ( excluding rock ) in trenches, plinth sides of foundations etc. in layers not exceeding 20cm ( twenty centimetre ) in depth, consolidating each deposited layer by ramming & watering including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Excavating, supplying & filling of local earth ( including roulaity ) by mechanical transport upto all leads, lifts also including ramming & watering of the earth in layers not exceeding 20 cm ( twenty centimetre ) in trenches, plinth, side of foundation etc. complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & laying cement concrete in retaining walls, return walls, walls ( any thickness ) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain windows sills, fillets, Sunken floor etc. upto all floor level, excluding cost of centring, shuttering & finishing 1 : 3 : 6 ( One cement : three coarse sand : six graded crushed stone aggregate 20 mm ( twenty milimetre ) nominal size ), including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing and laying in position cement concrete of specified grade mechanically mixed and curing complete excluding the cost of centering and shuttering - All work up to plinth level and all floor level in 1:4:8 (one Cement : four coarse sand : eight graded stone aggregate 40mm (forty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying in position cement concrete of specified grade mechanically mixed and curing complete excluding the cost of centering and shuttering - All work up to plinth level and all floor level in 1:5:10 (One Cement : five coarse sand : ten graded stone aggregate 40mm (forty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) mechanically mixed and vibrating curing complete including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor all level, excluding the cost of centering, shuttering and finishingin 1:1.5: 3 (one cement : One and half coarse sand : three graded stone aggregate 20mm ( twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Making plinth protection 50 mm ( fifty milimetre ) thick of cement concrete 1 : 3 : 6 ( One cement : three coarse sand : six graded stone aggregate 20 mm ( twenty milimetre ) nominal size ) over 75 mm ( seventy five milimetre ) thick bed of dry brick ballast 40 mm ( forty milimetre ) nominal size, well rammed & consolidated & grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying in position cement concrete of specified grade mechanically mixed , vibrated & curing complete excluding the cost of centering, shuttering, finishing & reinforcement - All work up to plinth level and all floor level in 1:1.5 : 3 (One Cement : One & half coarse sand : five graded stone aggregate 20mm (twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying reinforced cement concrete work in walls (any thickness), mechanically mixed, vibrated and curing complete including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor all level , excluding cost of centering, shuttering, finishing and reinforcement in 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20mm ( twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor all level mechanically mixed, vibrated and curing complete, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20mm ( twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing form work with steel plates 3.15mm ( three point fifteen millimeter ) thick welded with angle iron in frame 30X 30X5mm ( thirty X thirty X five millimeter ) so as to give a fair finish including centering ,shuttering, strutting and propping etc. with wooden battens and ballies , height of propping and centering below supporting floor to ceiling not exceeding 4.00 meters ( four meters ) and removal of the same for insitu- reinfoced concrete and plain concrete work including all leads and lifts of materials or as per the directions of Engineer in Charge.

Foundations, footings, bases of columns, etc. for mass concrete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Suspended floors, roofs, landings, balconies and access platform including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Lintels, beams, plinth beams, girders, bressumers and cantilevers including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Columns, Pillars, Piers, Abutments, Posts and Struts Circular including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Stairs, (excluding landings) except spiral stair cases including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Edges of slabs and breaks in floors and walls Under 20cm ( twenty centimeter ) wide including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Weather shade, Chajja, Corbels etc. including edges including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Retaining walls, walls (any thickness) including attached pilasters, butteresses, plinth and string courses fillets, kerbs & steps etc.including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and placing steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto floor all level. Thermo-Mechanically Treated bars of grade Fe-500 D or more including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and placing steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto floor all level. Thermo-Mechanically Treated bars of grade Fe-500 D or more including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. ( For septic tank with soak pit ) .

Rat trap bond brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation & plinth in all shapes and sizes in Cement mortar 1 : 6 ( One cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Rat trap bound brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes in Cement mortar 1 : 6 (one cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation & plinth in all shapes and sizes in Cement mortar 1 : 6 ( One cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation & plinth in all shapes and sizes in Cement mortar 1 : 4 ( One cement : four coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.( For septic tank with soak pit ) .

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes in Cement mortar 1 : 6 (one cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1 :4 ( One cement : four coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes : Cement mortar 1 : 4 ( One cement : four coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing 18 mm ( eighteen milimetre ) thick gang saw cut, mirror polished, premoulded & prepolished, machine cut for kitchen plateforms,vanity counters, window sills, facias & similar locations of required size, approved shade, colour & texture laid over 20 mm ( twenty milimetre ) thick base cement mortar 1 : 4 ( One cement : four coarse sand ), joints treated withwhite cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, coulding & polishing to edges to give high glass finish etc. complete at all level Granite of any colour, shade & all area of slab including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying Ceramic glazed wall tiles of size 300mm x 300 mm ( three hundred millimeter X three hundred millimeter )(thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except burgundy, bottle green, black of any size as approved by the Engineer-in-Charge in Skirting, risers of steps & dado over 12 mm ( twenty millimeter ) thick bed of cement mortar 1:3 (one Cement : three Coarse sand) and jointed with grey cement slurry @ 3.3kg/ sq.m (three point three zero kilograme per square meter ) including pointing in white cement mixed with pigment of matching shade complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing panelled or paneled & glazed shutters for doors, windows and clerestory windows fixing with hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-Charge. ( Butt hinges & necessary screws shall be paid separately ) Second class Teak wood , 35 mm ( thirty five milimetre ) thick shutters, including all leads,lifts & carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing panelling or panelling & glazing in panellled & glazed shutters for doors, windows & clerestory windows ( Area of opening for panel inserts excluding portion inside grooves or rebates to be measured ). Panelling for panelled or panelled & glazed shutters 25 mm to 40 mm ( Twenty five milimetre to forty milimetre ) thick Pre- laminated particle board with decorative lamination on one side & balancing lamination on other suide, Grade-I, Type-II IS : 12823 marked, including all leads,lifts & carriage of materials & to the entire entire satisfaction of Engineer-in-Charge

Providing & fixing panelling or panelling & glazing in panellled & glazed shutters for doors, windows & clerestory windows ( Area of opening for panel inserts excluding portion inside grooves or rebates to be measured ). Panelling for panelled or panelled & glazed shutters 25 mm to 40 mm ( Twenty five milimetre to forty milimetre ) thick float glass panes 5.00 mm ( five milimetre ) thick glass panes ( weight not less than 12.50 kg ( Twelve point five zero kilograme ) per square metre including all leads,lifts & carriage of materials & to the entire entire satisfaction of Engineer-in-Charge

Providing & fixing ISI marked flush door shutters conforming to IS : 2202 ( Part-I ) decorative type, core of block board construction with frame of first class hard wood & well matched teak three ply veneering with vertical grains or cross bands & face veneers on both faces of shutters 35 mm ( thirty five milimetre ) thick including ISI marked stainless steel butt hinges with necessary screws including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing wire gauge shutters using galvanised mild steel gauge of average width of aperture 1.4 mm ( one point four milimetre ) in both directions with wire of dia 0.63 mm ( zero point six three milimetre ) for doors, windows & clerestory windows with hinges & necessary screws 35 mm ( thirty five milimetre ) thick shutters Kiln seasoned & chemically treated hallack wood including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing wooden moulded beading to door & windows frames with iron screws, plugs & priming coat on unexposed surface etc. complete second class teak wood 50 x 12 mm ( fifty into twelve milimetre ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing mild steel grills of required pattern in frames of steel windows etc. with mild steel flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc. including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium sliding door bolts, ISI marked anodised ( Anodic coating not less than grade AC 10 as per IS:1868 ), transparent or dyed colour to required colour or shade, with nuts & screws etc. complete 300 x 16 mm ( three hundred into sixteen milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium sliding door bolts, ISI marked anodised ( Anodic coating not less than grade AC 10 as per IS:1868 ), transparent or dyed colour to required colour or shade, with nuts & screws etc. complete 250 x 16 mm ( two hundred fifty into sixteen milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 200 x 10 mm ( two hundred into ten milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 100 x 10 mm ( One hundred into ten milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium handles ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 125 mm ( one hundred twentyfive milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium handles ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 100 mm ( one hundred milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium hanging floor stopper ISI marked anodic coating not less than grade AC 10 as per IS: 1868 ) transparent or dyed to required colour & shade, with necessary screws etc. complete Single rubber stopper including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium hanging floor stopper ISI marked anodic coating not less than grade AC 10 as per IS: 1868 ) transparent or dyed to required colour & shade, with necessary screws etc. complete Twin rubber stopper including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing Cub board shutters 19 mm ( nineteen milimetre ) thick with pre-laminated flat pressed three layers particle board or graded wood particle board IS: 12823 marked exterior grade ( Grade I type II ) , having one side decorative lamination & other side balancing lamination, including second class teak wood lipping of 25 mm wide 12 mm thick ( twenty five milimetre wide twelve milimetre ) thick ) with necessary screws & bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing decorative high pressure laminated sheet of plain/ wood grain in gloss /matt/ Suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS: 2046 Type-S, including cost of adhesive of approved quality 1.00 mm ( One point zero zero milimetre ) thick sheet including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing 19 mm ( Nineteen milimetre ) thick water proof commercial board in shelves/box for Cub board with butt joints & fixing with nails & screws etc. complete, including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing ply wood 4 mm ( four milimetre ) thick, one side decorative veneer conforming to IS: 1328 (Type-1 ), for plain lining/ cladding with necessary screws, including priming coat on unexposed surface with decorative veneer facing of approved manufacture including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing special quality bright finished brass cub board or ward robe locks with four levers of approved quality including necessary screws etc. complete 50 mm ( fifty milimetre ) size, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing 50mm ( fifty milimetre ) bright finished brass cub board or ward robe knob of approved quality with necessary screws, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand ) logo with ISI, IS:3564, embossed on the body, door weight upto 35Kg ( Thirty five kilogram ) door with upto 700mm ( seven hundred milimetre ) with necessary accessories & screws etc. complete, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing magetic catcher of approved quality in Cub board/ ward robe shutters, including fixing with necessary screws etc. complete double trip ( horizontal type ), including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing expandable fasterners of specified size with necessary plastic sleeves & galvanised mild steel screws including drilling holes in masonry work/ cement concrete/ reinforced cement concrete & making good etc. complete 40 mm long, including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position & applying a priming coat of approved steel primer using structural steel etc. as required in grating, frames, guard bars, ladders, railing, brackets, gates & similar work including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing & similar works, including applying priming coat of approved steel primer mild steel tube/pipe, including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing fly proof wire gauge to windows, clerestory windows & door with mild steel flat 15 x 3 mm ( fifteen into three milimetre ) & nuts & bolts complete. Galvanised mild steel wire gauge with 0.63 mm ( zero point six three milimetre ) dia wire & 1.4 mm ( One point four milimetre ) aperture on both sides including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing factory made ISI marked steel glazed doors, windows & ventilators, side/ top/ centre hung, with beading & all member such as F7D, F4B, K11B & K12B etc. complete of standard rolled steel sections, joints mitred & flash butt welded & sash bars tenoned & riveted, including providing & fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings complete all as per approved design ( Sectional weight of only member shall be measured for payment ) fixing with 15 x 3 mm ( fifteen into three milimetre ) lugs 10cm ( ten centimetre ) long embedded in cement concrete block 15 x 10 x 10 cm ( fifteen into ten into ten centimetre ) of cement concrete 1 : 3 : 6 ( One cement: three coarse sand : six graded stone aggregate 20 mm ( twenty milimetre ) nominal size ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing mild steel Tubular frames for doors, windows, ventilators & cub board with rectangular/L- type sections made of 1.60 mm ( One point six zero milimetre ) thick mild steel sheet, joints mitred welded & grinded finish, with profile of required size, including fixing of necessary butt hinges & screws & applying a priming coat of approved steelprimer. Fixing with 15 x 3 mm ( fifteen into three milimetre ) lugs 10cm ( ten centimetre ) long embedded in cement concrete block 15 x 10 x 10 cm ( fifteen into ten into ten centimetre ) of cement concrete 1 : 3 : 6 ( One cement: three coarse sand : six graded stone aggregate 20 mm ( twenty milimetre ) nominal size ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing glass panes with putty & glazing clips in steel doors, windows, clerestory windows all complete with 4 mm ( four milimetre ) thick glass panes including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Cement concrete flooring 1 : 2 : 4 ( One cement : two coarse sand : four graded stone aggregate ) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm ( forty milimetre ) thick with 20mm ( twenty milimetre ) nominal size ) stone aggregate including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Mirror polished Kotah stone slab flooring over 20 mm ( twenty milimetre ) ( average ) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing & polishing complete with base of cement mortar 1 : 4 ( one cement : four coarse sand ) 19 mm ( ninteen milimetre ) thick, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Mirror polished Kotah stone slab 20 mm ( twenty milimetre ) thick in risers of steps, skirting, dado & pillars laid on 12 mm ( twelve milimetre ) ( average ) thick cement mortar 1 : 3 ( One cement : three coarse sand ) & jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing & polishing complete, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08 % & conforming to IS 15622, of approved make, in all colours and shades, laid on 20 mm ( twenty milimetre ) thick cement mortar 1 : 4 ( One cement : four coarse sand ), jointing with grey cement slurry @ 3.3( three point three ) Kilogram per square metres including grouting the joint with white cement & matching pigments etc. complete size of tile 300 x 300 mm ( three hundred into three hundred milimetre ) , including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & laying vitrified double charge floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08 % & conforming to IS 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1 : 4 ( One cement : four coarse sand ), jointing with grey cement slurry @ 3.3 ( three point three ) Kilogram per square metres including grouting the joint with white cement & matching pigments etc. complete size of tile 600 x 600 mm ( six hundred into six hundred milimetre ) , including all leads, lifts, & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & laying vitrified double charge tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08 % & conforming to IS 15622, of approved make, in all colours and shades, in skirting, riser of steps,over 12 mm ( twelve milimetre ) bed of cement mortar 1 : 3 ( One cement : three coarse sand ), jointing with grey cement slurry @ 3.3 ( three point three ) Kilogram per square metres including grouting the joint with white cement & matching pigments etc. complete size of tile 600 x 600 mm ( six hundred into six hundred milimetre ) , including all leads, lifts, & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Stone work ( machine cut edge ) for wall lining etc. ( Veneer work ) in all height, backing filled with a grout of average 12 mm ( twelve milimetre ) thick cement mortar 1 : 3 ( One cement : three coarse sand ) including pointing in white cement mortar 1 : 2 ( One white cement : two stone dust ) with an admixture of pigment matching the stone shade : ( To be secured to the backing & the sides by means of cramps & pins which shall be paid for separately ) Gang saw cut stone 30 mm ( thirty milimetre ) thick Red sand stone including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing on wall face PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion, Single socketed pipes complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- 110mm ( One hundred ten millimeter ) diameter metre.

Providing and fixing on wall face PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- Bend 87.5° 110mm ( eighty seven point five degree one hundred ten millimeter ) bend.

Providing and fixing on wall face PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- Shoe ( Plain )110mm ( One hundred ten millimeter ) shoe.

Providing & fixing mild steel holder bat clamps of approved design to cast iron or S.C.I. rain water pipes embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1 : 2 : 4 mix ( One cement : two coarse sand : four graded stone aggregate 20 mm nominal size ) & cost of cutting holes & making good the wall etc. 110 mm ( One hundred ten milmetre ) diameter PVC pipe including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

15mm ( fifteen millimeter ) cement plaster on the rough side of single or half brick wall of mix : 1:4 (one cement: four fine sand) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

15mm ( fifteen millimeter ) cement plaster on the rough side of single or half brick wall of mix : 1:6 (one cement: six fine sand) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

6mm ( six millimeter ) cement plaster of mix 1:4 (one cement : four fine sand) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & applying plaster of paris putty of 2 mm ( two milimetre ) thickness over plastered surface to prepare the surface even & smooth complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Distempering with oil bound washable distemper of approved brand & manufacture to give an even shade new work ( two or more coats ) over and including water thinnable priming coat with cement primer including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing walls with 100 % premium acrylic emulsion paint having VOC less than 50 ( Fifty ) gram per litre UV resistance as per IS 15489: 2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade ( Company Depot Tined ) with silicon additives new work ( Two or more coats applied @ 1.43 ( One point four three ) Litre per 10 ( ten ) square metres over & including priming coat of exterior primer applied @ 0.90 ( zero point nine zero ) litre per 10 ( ten ) Square metres, including all leads, ,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Finishing walls with Acrylic smooth exterior paint with of required shade new work ( two or more coat ) applied @ 1.67 litre/10 Sqmt ( one point six seven litre per ten square metres ) over & including priming coat of exterior primer applied @ 2.20 Kg /10 Sqmt ( at the rate two point two zero kilograme per ten square metre ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications,two or more coats applied on walls @ 1.25 ltr/ 10sqm( One point two five litre per ten square meter ) over an under coat including one coat of special primer applied @ 0.75 ltr/ 10sqm( zero point seven five litre per ten square meter ) of approved brand and manufacture complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10sqm ( zero point nine zero litre per ten square meter ) over an under coat of primer applied @0.75 ltr/10 sqm ( zero point seven five litre per ten square meter )of approved brand and manufacture complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10sqm( zero point nine zero litre per ten square meter ) over an under coat of primer applied @ 0.80 ltr/ 10sqm( zero point eight zero litre per ten square meter ) of approved brand and manufacture complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm ( one hundred millimeter ) sand cast Iron P or S trap, 10 litre ( ten litre ) low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge: White Vitreous china Orissa pattern W.C. pan of size 580mm x 440mm ( five hundred eighty millimetre X four hundred forty millimeter ) with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10litre ( ten litre )low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing white vitreous china flat back half stall urinal of size 580mm x 380mm x 350mm ( five hundred eighty millimeter X three hundred eighty millimeter X three hundred fifty millimeter ) with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge :- Single half stall urinal with 5 litre ( five litre ) P.V.C. automatic flushing cistern.

Providing and fixing wash basin with C.I. brackets, 15mm ( fifteen millimeter ) C.P. brass pillar taps, 32mm ( thirty two millimeter ) C.P.brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- White Vitreous China wash basin size 630mm x 450mm ( Six hundred thirty millimeter X four hundred fifty millimeter ) with single 15mm ( fifteen millimeter ) C.P. Brass pillar tap .

Providing and fixing wash basin with C.I. brackets, 15mm ( fifteen millimeter ) dia C.P. brass single hole basin mixer of approved quality & make, including painting of fittings and brackets, cutting and making good the walls wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- White Vitreous China wash basin size 550mm x 400mm ( Five hundred fifty millimeter into four hundred millimeter ) with 15mm ( fifteen millimeter ) C.P. Brass single hole basin mixer.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing stainless steel A ISI 304 ( 18/8 ) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm ( forty milimetre ) including painting of fittings & brackets, cutting & making good the walls wherever required kitchen sink without drain board 470 x 420 mm ( four hundred seventy into four hundred twenty milimetre ) bowl depth 178 mm, ( One hundred seventy eight milimetre ) including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing and fixing 600mm x 450mm ( Six hundred millimeter into four hundred fifty millimeter ) beveled edge mirror of superior glass (of approved quality) complete with 6mm ( six milimetre ) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing 600mm x 120mm x 5mm ( Six hundred millimeter into one hundred twenty millimeter into five millimeter ) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm ( forty millimeter ) long screws, rawl plugs etc., complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing C.P. brass toilet paper holder complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing PTMT liquid soap container 109mm ( one hundred nine millimeter ) wide, 125mm( one hundred twenty five millimeter ) high and 112mm( one hundred twelve millimeter ) distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105gms ( one hundred five grams ) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providuing & fixing PTMT towel rail complete with brackets fixed to wooden cleats with C.P. brass screws with concealed fittings arrangement of approved quality & colour, 450 mm ( Four hundred fifty milimetre ) long towel rail with total length of 495 mm, 78 mm ( Four hundred ninety five milimeter, seventy eight milimetre ) wide & effective height of 88 mm ( eighty eight milimetre ) , weighting not less than 170 ( One hundred seventy ) grams including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre ( one metre ) spacing. This includes testing of joints complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- 1216 (16 mm ( sixteen millimeter ) OD) pipe.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre ( one metre ) spacing. This includes testing of joints complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:-1620 (20mm ( twenty millimeter ) OD) pipe.

Providing & fixing PVC Cowl ISI marked including fixing with approved adhesive etc. complete 110 mm ( One hundred ten milimetre ) dia,including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing PVC Coller ISI marked including fixing with approved adhesive etc. complete 110 mm ( One hundred ten milimetre ) dia,including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing and fixing G.I. pipes complete with G.I. fittings & Clamps including making good the walls etc. concealed pipe including painting with anti corrosive bitumastic paint, cutting & making good the walls including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. internal work:-15mm ( fifteen millimeter ) dia nominal bore.

Providing and fixing G.I. pipes complete with G.I. fittings including making good the walls etc. concealed pipe including painting with anti corrosive bitumastic paint, cutting & making good the walls including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. internal work :- 20mm ( twenty millimetre ) dia.

Providing & fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting & making good the wall & floors etc. complete 110mm x 75 mm ( One hundred ten milimetre into seventy five milimetre ),including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing 100 mm ( One hundred milimetre ) Chromium plated grating for gully, floor or Nahni trap, including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.External work:-15mm ( fifteen millimeter ) dia nominal bore.

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- 25 mm to 40mm ( twenty five millimeter to forty millimeter ) nominal bore.

Fixing water meter & stop cock in G.I. pipe line including cutting & threading the pipe & making long screws etc. complete ( Cost of water meter & stop cock to be paid separately ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS : 8931, complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. 15mm( fifteen millimeter ) nominal bore .

Providing and fixing C.P. brass stop cock ( Concealed ) of standard design & of approved make conforming to IS : 8931, complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. 15mm( fifteen millimeter ) nominal bore .

Providing and fixing C.P. brass angle valve for basin mixer & geyser point of approved quality conforming to IS : 8931, complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. 15mm( fifteen millimeter ) nominal bore .

Providing & fixing C.P. brass extension nipple ( size 15 mm x 50 mm ( fifteen milimetre into fifty milimetre ) of approved make & quality as per direction of Engineer-in-Charge including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20mm ( twenty millimeter ) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40mm ( forty millimeter ) nominal size), inside plastering 12mm ( twelve millimeter ) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20mm ( twenty millimeter ) nominal size) finished with a floating coat of neat cement complete as per standard design complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. : Inside size 90cm x 80cm and 45cm ( Ninety centimeter into eighty centimeter and forty five centimeter ) deep including C.I. cover with frame (medium duty) 455 x 610 mm ( Four hundred fifty five into Six hundred ten millimeter ) internal dimensions, total weight of cover and frame to be not less than 38 kg ( thirty eight kilogram ) (weight of cover 23 kg ( twenty three kilogram ) and weight of frame 15 kg( fifteen kilogram ) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.50.

Providing & fixing soil, waste & vent pipe 100 mm ( one hundred milimetre ) dia Centrifugally cast ( Spun ) iron scoket & spigot ( S & S ) pipe as per IS : 3989 including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing soil, waste & vent pipe 75 mm ( Seventy five milimetre ) dia Centrifugally cast ( Spun ) iron scoket & spigot ( S & S ) pipe as per IS : 3989 including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & filling the joints with Spun Yarn, cement slurry & cement mortar 1 : 2 ( one cement : two fine sand ) in S.C.I./C.I. pipe 100mm ( One hundred milimetre ) dia pipe including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & filling the joints with Spun Yarn, cement slurry & cement mortar 1 : 2 ( one cement : two fine sand ) in S.C.I./C.I. pipe 75 mm ( Seventy five milimetre ) dia pipe including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing mild steel holder bat clamps of approved design to cast iron/ Cast iron ( Spun) pipes embedded in and including cement concrete blocks 10 x 10 x 10 cm ( ten into ten inti ten centimetre ) of 1 : 2 : 4 mix ( One cement : two coarse sand : four graded stone aggregate 20 mm ( twenty milimetre ), including cost of cutting holes good the walls etc. including carriage of materials in all leads and lifts and as directed by the Engineer in Charge, For 75 mm ( Seventy five milimetre ) dia pipe.

Providing & fixing bend of required degree with access door, insertion rubber washers 3 mm ( three milimetre ) thick bolts & nut complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge, 100 mm ( One hundred milimetre ) dia Sand cast iron S & S as per IS: 1729

Providing & fixing bend of required degree with access door, insertion rubber washers 3 mm ( three milimetre ) thick bolts & nut complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge, 75 mm ( Seventy five milimetre ) dia Sand cast iron S & S as per IS: 3989

Providing & fixing plain bend of required degree including carriage of materials in all leads and lifts and as directed by the Engineer in Charge, 100 mm ( One hundred milimetre ) dia Sand cast iron S & S as per IS: 3989

Providing & fixing plain bend of required degree including carriage of materials in all leads and lifts and as directed by the Engineer in Charge, 75 mm ( Seventy five milimetre ) dia Sand cast iron S & S as per IS: 3989

Providing & fixing Sand cast iron S & S off sets including carriage of materials in all leads and lifts and as directed by the Engineer in Charge, 150 mm ( One hundred fifty milimetre ) off sets 100 mm ( One hundred milimetre ) dia pipe as per IS: 3989

Providing & fixing Sand cast iron S & S off sets including carriage of materials in all leads and lifts and as directed by the Engineer in Charge, 150 mm ( One hundred fifty milimetre ) off sets 75mm ( Seventy five milimetre ) dia pipe as per IS: 3989

Providing & fixing collar 100 mm ( One hundred milimetre ) Sand cast iron S & S as per IS : 3989 including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing collar 75 mm ( Seventy milimetre ) Sand cast iron S & S as per IS : 3989 including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing lead caulked joints to sand cast iron/ centrifugally cast ( Spun ) iron pipe & fittings of diametre 100 mm ( One hundred milimetre ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing lead caulked joints to sand cast iron/ centrifugally cast ( Spun ) iron pipe & fittings of diametre 75 mm ( Seventy five milimetre ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing trap of self cleaning design with screws down or hunges grating with or without vent arm complete, including cost of cutting & making good the walls & floors 100 mm ( One hundred milimetre ) inlet & 100 mm ( One hundred milimetre ) outlet Sand cast iron S & S as per IS: 3989 including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing trap of self cleaning design with screws down or hunges grating with or without vent arm complete, including cost of cutting & making good the walls & floors 100 mm ( One hundred milimetre ) inlet & 75 mm ( Seventy five milimetre ) outlet Sand cast iron S & S as per IS: 3989 including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing in position precast reinforcement coment concrete manhole cover & frame of required shape & approved quality LD- 2.5 ( Two point five ) rectangular shape 600 x 450 mm ( six hundred into four hundred fifty milimetre ) internal dimensions including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing in position precast reinforcement coment concrete manhole cover & frame of required shape & approved quality LD- 2.5 ( Two point five ) square shape 450 mm ( four hundred fifty milimetre ) internal dimensions including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Supplying & filling brick bats in dispension trenches ( Brick aggregate ( Single size ) 50 mm ( Fifty milimetre ) nominal size ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing high pressure PVC spigot & socket, waste & ventilating pipes ISI marked including fixing with approved adhesive etc. complete 110 mm ( One hundred ten milimetre ) dia including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing high pressure PVC spigot & socket, waste & ventilating pipes ISI marked including fixing with approved adhesive etc. complete 75 mm ( Seventy five milimetre ) dia including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing PVC Cowl ISI marked including fixing with approved adhesive etc. complete 110 mm ( One hundred ten milimetre ) dia,including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Supplying & filling in plinth with sand under floors including watering, ramming, consolidating & dressing complete, including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Supplying & filling broken or crushed stone aggregate Chipping 40 mm ( forty milimeter ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.