WELCOME MAINTENANCE FOR OFFRs/JCOs/ORs MD ACCN AT MIL STN NAHAN UNDER GE CHANDIGARH

Amount

Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Demolition of Cement concrete unreinforced as in Ground Floor and paving n. exc. 15cm thick (above or below G.L.) complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames n.exc 1.5 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames exc 1.5 sqm but n.exc 4 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts etc complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description not exc 1 sqm each and refixing in the same opening complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and refixing in the same opening complete all as specified and directed by Engineer-in-Charge.

Dismantling of cast iron pipe/ PVC drain pipes/PVC (SWR) pipe etc, 110mm jointed in cement mortar and taking out of trenches and wall, if required complete all as specified and directed.

Dismantling of cast iron pipe/ PVC drain pipes/PVC (SWR) pipe etc, 75mm jointed in cement mortar and taking out of trenches and wall, if required complete all as specified and directed.

Dismantling wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete, all as specified and as directed by Engr-in-charge.

Dismanntling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering etc complete all as specified and directed.

Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description and in any position not otherwise provided for, Complete all as specified and as directed

Dismantling unframed timber scantlings 40 sq. cm and over in section, in any position, Complete all as specified and as directed

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones (upto 4th storey of building) complete all as specified and directed by Engr-In-Charge.

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring etc., and making good, cutting not exc 10 cm girth and complete all as specified and directed by Engineer-in-Charge.

M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface ofthe sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified.

Disconnecting/dismantling existing tanks of capacity exc. 500 ltr & n. exc. 1000 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.

Disconnecting/dismantling existing tanks of capacity exc. 250 ltr & n. exc. 500 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.

Disconnecting existing tanks , setting aside (or lowering if required) for repair, cleaning, etc. and hoisting if required reconneecting and refixing in position (Cleaning repairing etc measured separately) exc 250 & n.exc 500 ltr in capacity complete all as specified

Disconnecting existing tanks , setting aside (or lowering if required) for repair, cleaning, etc. and hoisting if required reconneecting and refixing in position (Cleaning repairing etc measured separately) exc 500 & n.exc 1000 ltr in capacity complete all as specified

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc(exc 250 & nexc 500 ltr), Complete all as specified and as directed

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc(exc 500 & nexc 1000 ltr), Complete all as specified and as directed

Demolition of brick work or stone/boulder masonary built in cement mortar incl all quions arches, pillar or any other descrption etc complete all as specified and directed by Engineer-in-Charge.

Supplying & fixing of PVC water storage tank 1000 ltr capacity HDPE triple layered ,white colour cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including 20/15 mm tank nipple, supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 mm - 210 gms ) complete Note : (i) Inlet, outlet & wash out pipe will be measured paid for separately. (ii) The quoted rate is inclusive of minimum one union each on inlet and outlet of water tank as per size of pipe shall be provided.

Supplying & fixing of PVC water storage tank 500 ltr capacity HDPE triple layered ,white colour cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including 20/15 mm tank nipple, supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 mm - 210 gms ) complete Note : (i) Inlet, outlet & wash out pipe will be measured paid for separately. (ii) The quoted rate is inclusive of minimum one union each on inlet and outlet of water tank as per size of pipe shall be provided.

Supplying & fixing in repairs of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 15 mm dia complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete (1:4:8) type D-2,using 40 mm graded stone aggregate as in foundations, filling and mass concrete, sub base to paver blocks etc complete all as specified and directed by Engineer-in-Charge.

Reinforced Cement Concrete Nominal mix ( 1 :2:4) using 20mm graded mechanically crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slab, landings and similar work not exceeding 200mm thick, horizontal or sloping finished rough complete.

TMT steel bars 10mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc. set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade, hardner, resin in the ratio of 8:1:2 laid mortar over and inculding 15 mm thick screed in cement mortar (1:6) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm as in floors etc. set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade, hardner, resin in the ratio of 8:1:2 laid mortar over and inculding 15 mm thick screed in cement mortar (1:6) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

Vitrified ceramic tiles ultra charged light shade 10 mm thick (Square/rectangular) polished, area of each tiles exceeding 0.42 Sqm but not exceeding 0.1 sqm, in floor etc set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade, hardner, resin in the ratio of 8:1:2 laid mortar over and inculding 15mm thick screed bedding layer in CM (1:6) complete all as specified and directed by Engineer-in-Charge.

Glazed ceramic coloured tiles 450 x 300 x 7mm thick on vertical surface such as skirting , dado etc. over and including 10 mm thick rendering in CM 1:4 thick set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade, hardner, resin in the ratio of 8:1:2 complete all as specified and directed by Engineer-in-Charge.

Granite 18-20 mm thick, (table rubbed and polished) in single piece (in one direction) machine cut, machine polished, bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:3) screed, as in cooking platform, shelves, RCC counters, window cills & similar situations, complete all as specified and directed by Engineer-in-Charge.

M&L out door/parking tiles heavy duty for light traffic non skid, anti scratch, heavy grip, vitreous/semi vitreous coloured, unique designs tiles 8 to 10mm thick area of each tile of size 300mmX300mm, in floors, parking/outdoor tiles etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM(1:6), complete all as specified and directed.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick in cement mortar 1:6, on fair faces of brick or concrete surfaces , trowelled to even and smooth surface without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick in cement mortar 1:4, on brick or concrete surfaces in two layers mixed with water proofing compound on top layer, trowelled to even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. NOTE: Water proofing compound shall be measured and paid separately.

Rendering 15 mm thick in cement mortar 1:4, on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing in two layers mixed with water proofing compound on top layer, trowelled to even and smooth without using extra cement, (upto 4th storey of building) complete all as specified and directed by Engineer-in-Charge. NOTE: Water proofing compound shall be measured and paid separately.

Supply only liquid water proofing comound ISI Marked complete all as specified and directed.

Rendering 5 mm thick in cement mortar 1:3 as in ceiling/soffits of slabs/Chajja/ Sunshade finishing the plastered surface even & smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and a priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over New surfaces on wall, incl necessary preparation works, (upto 4th storey of building) complete all as specified and as directed.

Preparation of old plastered surfaces of wall and applying two coats of cement base paint on walls including preparation of surface (upto 4th storey of building) complete all as specified and directed.

Preparation of plastered or unplastered new surfaces of ceilings and applying three coats of white wash including preparation of surface complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper on walls including preparation of surface complete all as specified and directed.

M&L for complete removal of existing surface and applying two coat of oil bound distemper over a coat of Chalk whiting, on plastered surfaces incl preparatory to distempering and primer on wall surfaces complete all as specified and as directed.

Preparation of old Plastered or un-plastered surfaces of ceilings etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying three coats of white wash on ceilings/ old decorated surfaces complete all as specified and directed by Engineer-in-Charge.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and a priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces in camouflaging pattern or in any other pattern after complete removal of existing treatment from wall surfaces etc (upto 4th storey of building) complete all as specified and as directed.

Preparation of walls brooming down, applying one coat of white cement based wall care putty 1 mm thick etc complete all as specified and directed by Engineer-in-Charge.

M&L for one coat of synthetic enamel paint over old painted wooden or wood based surfaces of any description, not otherwise described over 10 cm width or girth, including preparation of surfaces complete all as specified.

M&L for one coat of synthetic enamel paint over old painted steel & iron surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces complete all as specified.

Preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

M&L for Preparation & painting Old painted surface and applying two coats of synthetic enamel paint (Ordinary tint) over and including red oxide zinc chrome, over CGI sheeting /surface of any description, over 10 cm in width or girth, Complete all as specified and as directed

Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

Factory made Pressed steel frames, confirming to IS, having profile 105 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid panel PVC Door shutter 30mm thick (stiles)consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain cover PVC 'C' channel having PVC strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails on either side & as gap insert for top rail & bottom rails, panelling of plain colour PVC sheet to be the fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site as per specification and drawing.

30 mm thick factory made Plain, framed, panelled shutters of 2nd class Hardwood (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkat complete all as specified and directed by Engineer-in-Charge.

30 mm thick factory made glazed & Skeleton shutters of 2nd class Hardwood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size ofstiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge.

Solid PVC door frames of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge complete all as specified and directed by Engineer-in-Charge.

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per drawings and the directions of Engineer-in-Charge

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless teel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer- in-charge.

S&F 125 mm Stainless steel, barrel tower bolts of extruded section and fixed, Complete all as specified and as directed

S&F Stainless steel 100 mm Butt hinges, hinge pin, anodised and fixed, type C-21, Complete all as specified and as directed

S&F 250 mm long Stainless steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

S&F 150mm size, Stainless Steel, D type with back plate, handle and fixed with screws complete all as specified.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete fixed in reapir all as specified and directed by Engineer-in-Charge.

Sheet glass 4 mm thick, ordinary quality and glazing with linseed oil pane putty & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane (upto 4th storey of building) complete all as specified and directed by Engineer-in-Charge.

4 mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm each and using Silicon for fixing of glass in addition to glazing putty (upto 4th storey of building) complete all as specified and directed by Engineer-in-Charge.

Stainless steel bracket and stainless steel fancy type fennel complete all as specified and directed by Engineer-in-Charge. Note: The quoted rate includes one pair comprising of two brackets and two fancy type fennels.

Material & labour for 25mm dia stainless steel pipe curtain rod, with decorative lining coating, fixed with & including stainless steel hooks/ brackets and decorative finials (at both side), curtain rings (minimum 5 Nos rings per running mtr of curtain rod) shade as approved by GE complete all as specified includng fixing of long size rawl plugs in wall for MS hook including taking out the existing old pelmet box along with old curtain rods complete all as specified and directed.

Material & labour for 25mm dia aluminium pipe curtain rod, powder coated fixed with & including stainless steel hooks/ brackets and decorative finials (at both side), curtain rings (minimum 5 Nos rings per running mtr of curtain rod) shade as approved by GE complete all as specified includng fixing of long size rawl plugs in wall for MS hook including taking out the existing old pelmet box along with old curtain rods complete all as specified and directed.

S&F Fe-410-W(Gde E-250)quality B rolled mild steel in roof trusses(Framed)trusses, purlin, crane gantries, rails anfd framing(beam, tee, angle, channel or flat section)including distance pieces , cleats etc.Complete all as specified and as directed

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed by Engineer-in-Charge.

Pre-painted galvalume aluminum zinc coating profile sheet GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Pre- painted galvalume aluminum zinc coating profile sheet GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping s crews as complete all as specified and directed.

S&F in repairs 4 mm thick bakelite sheet printed/wood grain finish/decorative choice fixed in aluminium panels complete all as specified and as directed by Engr-in-Charge

S&F 17/18 mm thick HDHMR one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work (including PVC strip on edges) in cupboards and other accesories etc as in repairs complete all as specified and as directed.

S & F in repair 19mm thick plyboard BWR type BB, fixed with screws to timber frame work as in kitchen cabinets , cupboards etc, complete all as specified and as directed.

S&F in repair 1.00 mm thick sunmica (Coloured) to be fixed with adhesive with plywood surfaces and wooden surfaces,Complete as per direcrtion of Engineer-In- Charge.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre incl fixing hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long for false ceiling with and incl 7mm thick laminated prepainted gypsum boards or tiles for insulation and accoustic purposes, 60cm x 60cm in size all as specified for size of grid 605 x 605mm

Providing and fixing False ceiling at all heights with fully perforated 12mm thick micro tegular edged or 10 mm thick square edged GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of size 595mm X 595mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRCO 0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476(part-4) -1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-grid of hot dipped galvanised iron section of 0.33 mm thick (galvanised @120 gms per sqm incuding both sides) comprising of main-T runners of size 15mm X 32mm of length 3000 mm, Cross-T of size 15mm X 32mm of length 1200 mm and secondary intermediate cross T of size 15mm X 32mm of length 600mm to form grid module of size 600mm X 600mm, suspended from ceiling using galvanised mild steel items (galvanising @80 gms/sqm) I.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85X25X2mm. Galvanised iron perimeter wall angle of size 24mmX24mmX0.40mm of length 3000 mm to be fixed on periphery wall/partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per direction of the Engineer-In-Charge.

S&F door strip (snake guard strip) minimum 18mm wide aluminium body and nylon brushes minimum 22mm wide alongwith screws for fixing complete all as specified and directed.

S&F in repair stainless steel plain basket, cutlery pan basket ,grain trolly, plate basket,cup soucer,partition, or any other basket of any description/pattern as approved by GE fixed with sliding channel revolving wheels , fixed to wood based frame work , complete all as specified and directed.

S&F in repair Continuous (piano hinges) 30mm width of flap in repairs Paino hinges, SS Gde-304, bright finish or electro galvanised (width of flap 30mm), complete all as specified and directed by Engineer-in-Charge.

S&F in repair 50 mm long magnatic catcher of brassalloy body superior quality and fixed with screw complete all as specified.

S&F in repair telescopic channel/slider to fiacilitate drawer slide on steel ball bearing 400-500 mm long and fixed in position with stainless steel screws , ISI marked , suitable for cupboard drawers , complete as per the sample kept in the office of Engr-in-charge

S&F in repair aluminium alloy, anodised, hasp staple (bolt type) 100 mm long hinge pin including fixing with bolts fixed in repair complete all as specified and directed by Engineer-in-Charge.

S&F for vitreous china white wash basin with flat back of size 550mmx400mm coloured including MS brackets, cutting for and pinning in ends of brackets, including bottle trap/ PVC waste pipe as in repairs complete all as specified and as directed.

S&F single piece WC of size 365x655x765 with flushing cistern and connection pipe, P or S trap (closed pattern incl all necessary accessories like rag bolts, kitt /gel gasket etc, (including flushing cistern, pvc seat cover , jet and flush pipe complete all as specifed and directed.

S&F for centre hole basin mixer 15mm dia with spout, fancy type, chromium plated Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed as in repair complete all as specified and as directed.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs stop/angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated with long shank and cup complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs chromium plated, Brass, Jet spray including flexible pipe 15mm bore, screwed down, high-pressure pipe of 15 mm bore with wall flange fixed to wash down water closet (pedestal pattern) complete all as specified and directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified as directed

Supplying and fixing in repairs Fancy type swivel shower chromium plated 15 mm dia, 195 mm long with a bend of 45 degrees with flange of PTMT as specified and directed by Engineer in Charge.

S&F in repairs toilet papper holder chromium plated with fixing to wall complete all as specified and directed.

Supply and fixing in repairs corner glass shelf assembly comprising of three pieces 5.5 mm thick toughened glass 300x300mm wide bevelled edge/ hatching of edges fixed with stainless steel "D" brackets with railing complete ,all as specified and directed by Engineer-in-charge.

S&F in repair brass chromium plated Tubler towel rail, 20mm dia, D type, 60cm long between flange, Complete all as specified and as directed

S&F in repair S&F sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement ortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, Complete all as specified and as directed

S&F in repair kitchen Plate Rack stainless steel having size 600mm x900mm x250mm (approx) incl fixing to walls with fasteing screws, rubber/PVC beading /capping complete to sustain utensils weight upto 8-10 Kg, complete all as specified and directed.

S&F in repair urinal waste pipe 32mm dia, 800mm long with cup and nuts fixed to sink/WHB complete all as specified & directed

S&F for PVC connections with PTMT nuts of length 450 mm long fixed to 15 mm bore iron pipe or union as in repair complete all as specified and as directed.

S&F chromium plated perforated grating 100/150mm dia over Floor/Nahani trap with or without hole for waste pipe fixed with white cement mixed with pigment to match the shade of floor fixed in repair, all as directed by Engineer-in-charge.

110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with and including MS clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts complete all as specified and directed by Engineer-in-Charge.

75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with and including MS clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore fixed in repair including jointing to waste pipe in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer in Charge.

PVC(SWR) bends (any radius), for 110mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

PVC(SWR) bends (any radius), for 75 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

CPVC(SDR-11) of outer dia 20 mm with and including CPVC SDR-11 fittings on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

CPVC(SDR-11) of outer dia 25 mm with and including CPVC SDR-11 fittings on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 25 mm dia CPVC ball valves as required complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including ,fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. all as specified and directed.

Taking down MCCB Incomer DB/MCB DB/AC Box/Meter box of any size and disposal under schedule of credit and making good disturbed surfaces all as specified and directed.

Taking down old unserviceable light fittings any type and removal from site and making good disturbed surfaces of walls, ceiling etc complete all as specified and directed by Engineer-in-Charge to match with existing surface all as directed.

Point wiring using approved colour coding as per IS ,with stranded copper conductor 1.5 sqmm (nominal area ) single core , flame retardant low smoke and low halogen FRLSH PVC insulated unsheathed , 1100 V grade conforming to IS 694 ,marked TEC and FIA approved in and including PVC conduit medium grade ISI marked 20mm dia with all fittings and accessories, concealed type/ surface type (surface type only on ceiling), PVC junction boxes, modular metal sunken/flush boxes of any modules from 2 to 18 Modules with Inner and outer modular cover plates, including FRLSH flame retardant low smoke and low halogen rigid PVC insulated unsheathed stranded copper conductor 1.5 Sqmm (nominal area )single core cable as earth continuity conductor to common earth and connected to earth dolly for One light point controlled by one switch or one (Ceiling/ Wall/ Exhaust) fan point controlled by one switch and regulator complete all as specified and directed by Engr-in-charge. Note :- 1. Cutting/chasing of wall etc. deemed to be included in the quoted rate of this item. 2. Modular metel flush/sunken Box along with modular switch/socket cover plate & sheet are inclusive in the item rate quoted. 3. Only switch socket and fan regulators to be measured and paid separately

All as per item No 125 above but controlled by two way switch.

All as per item No 125 above but one call point controlled by one bell point.

All as per item No 125 above but for one 3 pin, 5 Amp socket on same board all as directed.

All as per item No 125 above but for one 3 pin, 5 Amp socket on indipendant board all as directed.

All as per item No 125 above but with 4 sqmm copper conductor for 15 amp socket with 2.5 sqmm earth continuity conductor.

Taking out /dismantling unsv Sub main wiring and S & F Sub main wiring with PVC insulated, FRLS cable 2 single core 6 Sq mm 1100 V grade with stranded copper conductor on and incl PVC rigid non metalic conduit (ISI marked) in concealed incl all specials like joint, elbow , Tee ,junction , bend etc and provision of PVC insulated copper conductor single core 4 sq mm for earth continuityconductor complete all as directed by Enginer-in-charge .

All as per item No 131 above but 2 run of 4 sqmm and one run of 2.5 Sqmm earth contuinity conductor

S&F of Modular snap switch SP one way 5/6 Amps suitable for 1 Module complete all as specified and directed.

S&F of Modular snap switch SP two way 5/6 Amps suitable for 1 Module complete all as specified and directed.

S&F of Modular bell push switch, SP one way 5/6 Amps suitable for 1 Module complete all as specified and directed.

S&F of Modular socket 5 pin 5/6 Amps suitable for 2 Module complete all as specified and directed.

S&F of Modular snap switch SP one way 15/16 Amps suitable for 1 Module complete all as specified and directed.

S&F of Modular socket 5/6 pin 15/16 Amps suitable for 2 Module complete all as specified and directed.

S&F of Modular Fan step Regulator electronic, 120 watts, 2 Module complete all as specified and directed.

S&F of ceiling rose surface backalite 65mm x 50 mm, two to three terminals complete all as specified and directed.

Supply and fix of Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and directed.

Supply and fixing Electric bell, AC,230 Volts single phase ding dong type complete all as specified and directed.

Supply and Fix MCB protected socket (Modular AC box) 4 module plasic box with 25A power unit complete all as directed and specified.

Supply and fixing of LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC,decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 8, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc flushed on the existing wall , to match with existing surface and making all necessary connections complete all as directed.

All as per Item No 146 above but SPN 04 way, 240 volts complete all as directed.

All as per Item No 146 above but SPN 12 way, 240 volts complete all as directed.

All as per Item No 146 above but TPN 04 way, 415 volts complete all as directed.

S&F of isolator DP 63 amp 230 Volt complete all as specified and directed.

S&F of isolator TPN 63 Amps, 415 volts complete all as directed.

S&F of isolator SP 6- 40 Amps, 220 volts , 50 Hzs, 10 KA , "C" series, ISI marked all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC Surface/recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.complete all as specified and as directed.

Supply and fixing of Indoor Decorative LED box type suitable for fixing ceiling/wall with aluminium base directly retro fit LED tube Light , 22 watt, , Color: Cool day light 4 ft white Operating Voltage: 140-270 volts complete with all accessories internally pre wired and including up with three core PVC copper flexible cable of size 23/0.0076 from ceiling rose to connector block complete all as specified and directed. Note: LED batten & LED tube rod shall be of same brand.

M&L in replacement of fabrication of sheet metal enclouser to accommodate 04 Nos electric meters of size 800 mm x 500 mm x 150 mm deep and 1.6 mm thick MS sheet, powder coated, bakelite sheet with side hung shutter including provision of locking arrangement and niche covered with 4 mm thick plain glass , including locking arrangement & open Wiring coverd with Flexible Pvc Pipe of suitable size complete all as specified and as directed.

Supply and fixing in replacement of 1100 volts grade heavy duty cable PVC insulated aluminiumconductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of size 10 sqmm 2 core complete all as directed.

Earthing complete with Galvanised steel earth plate electrode of size 60cmx 60cm x 6mm thick electrode buried directly in ground (earth pit not less than 2.25 meters deep below the normal ground level) with top edge of the plate not less than 1.5 m below normal Ground Level connected to GI earth wire 4 mm dia by means of bolts, nuts, check nuts and washers and earth lead protected by 15mm dia GI pipe medium grade connected to main distribution board/ earthing test point all as shown on electrical plate No-03 of SSR Part-1 and all as specified including testing on completion.Note: The unit rate shall also include for excavation, earth work in hard/dense soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bars @ 150mm c/c both ways , GI funnel with watering pipe 20 mm dia, wire mesh, salt and charcoal, protection pipe for earth lead upto 7.50m long complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified in SSR part-II earth lead wire and protection pipe beyond 7.5m shall be measured and paid separately.

Note: For the purpose of arriving at lumpsum amount, the amount of credit schedule i.e Sch 'A' section II (i.e Rs 92,266.00 shall be deducted from the total amount arrived.

Total of Schedule 'A' Rs.

TANUJ SAINI CONTRACTOR (BID ID -3342325)

Bairagi Builders (BID ID -3347619)