SPECIAL REPAIR TO BLDG NOS P-44 AND P-09 IN MH AREA AT MIL STN KOTA

Amount

Taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Demolition/Dismantling of existing normal roof treatment, any type from RCC roof slab including lime concrete/PCC padding over roof, removing layer of bitumen under lime concrete/PCC padding, cement mortar, felt etc and cleaning the surface by hacking to receive plaster and removing demolished materials outside MD land, complete all as specified and directed.

Taking down chowkhat or frames not exc 1.50 Sqm each with shutters (with out taking off shutters from the frame), complete all as specified and directed.

Taking down chowkhat or frames exc 1.50 Sqm and not exc 4.00 Sqm each with shutters (with out taking off shutters from the frame), complete all as specified and directed.

Taking down shutters of any description not exc. 1.0 Sqm each and removing from site complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc 15 cm thickness (below or above GL), complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete as specified and directed.

Demolition of cement concrete (reinforced) such as roofs, floors (other than ground floors), beams, stair cases, landing, chhajjas and other similar works and removing rubbish from premises, complete all as specified and directed.

Dismantling cast iron work of any description, complete all as specified and directed.

Dismantling floor, hearth or wall tiling/ terrazzo including cement mortar bedding (but not backing), removing tiles and rubbish off the premises, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles, complete all as specified and directed.

M&L for PCC 1:2:4 mix type B-0 (Using 12.5 mm graded crushed stone agg) for roof padding, leveling course to receive floor finishes etc, complete all as specified and directed.

M&L brushing neat cement slurry with 3.00 kg cement per Sqm, complete all as specified and directed.

M&L for applying 15 mm thick screed in CM 1:4 on roof slabs with using liquid water proofing compound as per manufacturer's instructions, complete all as specified and directed. (Liquid WPC shall be measured and paid separately).

M&L for cleaning of roof slab including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to IS 3384 @ of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of cold applied bituminous primer conforming to IS:3384 @ 0.40 Kg/Sqm.

Item 15.00 Contd........ (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm (minimum) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimney/other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen. (v) Cost of above aspects is deemed to be included in quoted rates.

Supply only approved liquid water proofing compound, complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium window and ventilator shutters, sliding type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, screws, anodised aluminium fittings such as suitable handle (1 No.), complete all as specified and directed.

S&F in replacement of top rail/bottom rail/lock rail/stiles of aluminium door/window/ventilator shutter, repair/adjustment including necessary materials such as aluminium sections of required size, cleats, rubber beading, handles etc including taking down and refixing of shutters, complete all as specified and directed.

Supply only stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed. Note :- Cost of fixing of SS cloth wire shall be included with aluminium shutter rates.

Supply and fixing in renewal of stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F 35mm thick factory made IInd Class Hard wood (Hollock) paneled door shutters two panel with lock rail and panel of 9mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12mm thick particle board veneered with commercial veneering on both faces. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S&F 35mm thick factory made IInd Class Hard wood (Hollock) glazed and skeleton, open rebated, prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered and rounded, fitted with cut and mitered beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S & F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing as applicable to item 08095 given in SSR Part – II (2020).

S & F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppy and fixing in the frame at site complete all as per specifications and drawings as applicable to item 08080 given in SSR Part–II.

S & F factory made steel windows with side hung shutters made of box type section & including projection type hinges, with 2 Nos steel handles, 2 Nos tower bolts & steel pag stay complete (with glazing bars), dovetailed or welded & including fixing of lugs in PCC 1:2:4, type B-1, using 20mm graded stone aggregate & making good walls & cills to match the existing and including one coat of red oxide/ zinc chrome primer complete all as specified and directed. complete all as specified and directed. Note :- Glass/SS or MS cloth wire shall be measured and paid for sepparately under respective items.

S & F factory made steel windows with side hung shutters made of box type section & including projection type hinges, with 2 Nos steel handles, 2 Nos tower bolts & steel pag stay complete (without glazing bars), dovetailed or welded including fixing of lugs in PCC 1:2:4, type B-1, using 20mm graded stone aggregate & making good walls & cills to match the existing and including one coat of red oxide/ zinc chrome primer complete all as specified and directed. Note :- Glass/SS or MS cloth wire shall be measured and paid for sepparately under respective items.

M & L for cutting holes in stone/brick/PCC blocks walls, exc. half brick but not exc.one brick built in cement mortar or in cement lime mortar for inserting holdfasts/cooler stand and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed, ISI marked complete all as specified and directed.

S&F aluminium handles, cast type, anodised 100 mm size, ISI marked complete all as specified and directed.

S&F 100 mm size mild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws, complete all as specified and directed.

S&F of 300 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

S & F 250 mm long aluminium alloy, anodised sliding door bolts (ISI marked) with bolt not less than 16mm dia with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium alloy and fixed complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, with hard drawn steel spring, fixed in floor, overall length of cover plate 140 mm, complete all as specified and directed.

S&F in renewal 18/19 mm thick pre-laminated MDF board (Grade I, type II), fixed as in kitchen cabinates, drawers etc, as per standardtrade practise, pre-laminated both side with white lamination, fixed with screws with timber frame work, complete all as specified and directed.

S&F in renewal 18/19 mm thick pre-laminated MDF board (Grade I, type II), fixed as in cupboard /cabinates shutters/drawer etc as per standardtrade practise, pre-laminated one side with 0.8mm thick decorative choice lamination and other side with white lamination, fixed with screws with timber frame work, complete all as specified and directed.

S&F in renewal 150mm long stainless steel handles as per existing of superior quality for cupboards complete all as specified and directed.

S & F in renewal continuous (piano) hinges, mild steel, bright finish or electro galvanised, width of flaps (when open) in 30mm complete all as specified and directed.

S&F in renewal auto close hinge as per existing of superior quality for kitchen cupboards complete all as specified and directed.

S&F in renewal 'D' type tubular towel rail 60 cm long, brass chromium plated, 20 mm dia, complete fixed with stainless steel screws, complete all as specified and directed.

S&F in renewal towel ring of PTMT, fixed with and including CP brass screws and wooden/plastic cleats (Minimum weight 90 grams), complete all as specified and directed.

S&F in renewal shelf of PTMT fixed with and including CP brass screws and wooden/PVC cleats (Minimum weight 300 gms), complete all as specified and directed.

S & F for 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc. 0.5 Sqm in each pane complete all as specified and directed.

M & L for 3mm thick figured glass pin head type and glazing with oil putty in squares not exc. 0.5 Sqm in each pane complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggreate), 75 mm thick as in plinth protection/Path/PCC paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where dirtected and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight), complete all as specified & directed.

M&L 100 mm thick PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in sub base of floors etc, finished even and fair, complete all as specified and directed.

M&L for laying fully vitrified paving tiles of size 300x300x20-22 mm thick, suitable for exterior areas, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles, laid over and including 15 mm thick screed in CM 1:6, complete all as specified and directed.

M&L precast (factory casted) cement concrete kerb stone casted in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate with plain or interlocking joints (as directed) including making groove in ground of desired dimension, including weathering, slightly rounded or chamfered angles, placing in position, set and jointed in CM 1:4, making good distrubed surface of ground complete all as specified and directed.

M&L brick work with old size pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

M&L for brick work with pulverised fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan to any radius in half brick walls built in cement mortar 1:4, complete all as specified and directed.

M&L for walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:6, complete all as specified and directed.

S&F mild steel framed work as in grills, grating etc. with end of bars shouldered and/or riveted, or forged into spikes: framed guard bars: barred iron doors: ladders: frame balusters: walk ways: railing: frame work of water tanks and similar works conforming to Fe-290 Grade-E-165, complete all as specified and directed.

S & F for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing & confirming to Fe.410W.Gde-E-250,quality-B complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets, complete all as specified and directed.

S&F Anodised aluminium snap grid frame work for false ceiling, size of grid 605x605 mm, including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, complete all as specified and directed.

S&F 10mm thick PVC insulation panels with EPS stuck to 1mm printed PVC sheet suitably placed as in false ceiling grid of size 605x605 mm made of Aluminium/G.I./M.S. as per specification, complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with screws complete all as specified and directed.

Dismantling in fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section complete all as specified and directed.

S&F Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing, complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing, complete all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in flooring/sub base finished rough to receive floor finishes/screed complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for light coloured vitrified tiles, 10mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L Glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm/450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in CM 1:4, complete all as specified and directed.

M&L for machine cut kota stone slab as in flooring 20 to 25 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including 15 mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for machine cut kota stone slab as in skirting, dado, risers etc, 17 to 22 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including 10 mm thick CM 1:4 backing, complete all as specified and directed.

M&L granite slab 18-20 mm thick, table rubbed and polished in cooking platform, jambs, cills, pillars, tread, risers, platform for WHB etc including bull nosing to exposed outer edges, set in CM 1:4 bedding and pointing with white cement mixed with pigment, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

Labour only for rounding to edges of kota stone/marble stone by making stone bull nosed/rounded as in floor, steps, cooking platform etc, complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:4, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 10 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:3, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:4, with using liquid water proofing compound as per manufacturer's instructions, surface finished even and smooth without using extra cement, complete all as specified and directed. Note : Liquid water proofing compound shall be measured and paid separately.

M&L for rendering 10 mm thick on fair faces of ceiling in cement mortar 1:4 including finishing the surface even and smooth, complete all as specified and directed.

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mitres and stopped ends, etc. complete all as specified and directed.

M&L for preparing new previously untreated plastered surfaces of walls and applying two coats of modified acrylic exterior emulsion paint over & including a coat of primer, complete all as specified and directed.

M&L for preparing new previously untreated plastered surfaces of walls and applying 3 mm thick Wall care putty as per manufacturer's instructions and over it applying two coats of distemper oil emulsion over a coat of primer, complete all as specified and directed.

M&L for applying three coats of white wash on ceiling including preparation of new or previously untreated surfaces, complete all as specified and directed.

M&L for applying two coats of white wash after preparation of old previously treated plastered surfaces of ceiling, complete all as specified and directed.

M&L complete removal of existing treatment from previously treated surfaces of walls and applying 3 mm thick Wall care putty as per manufacturer's instructions and over it applying two coats of distemper oil emulsion over a coat of primer, complete all as specified and directed.

M&L complete removal of existing treatment from previously treated surfaces of walls and applying two coats of modified acrylic emulsion paint over a coat of suitable primer, complete all as specified and directed.

M & L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of 1st grade quality over and including one coat of pink primer complete all as specified and directed.

M & L for preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of 1st grade quality over and including one coat of red oxide zinc chrome primer complete all as specified and directed.

M & L for preparation new or previously untreated steel surfaces of any description not exc 10 cm width or girth and applying two coats of synthetic enamel paint of 1st grade quality over and including one coat of red oxide zinc chrome primer complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M & L for preparation of old painted wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of 1st grade quality over and including one coat of pink primer complete all as specified and directed.

S&F in renewal stainless steel tubular curtain rods, 25 mm dia, with fixing brackets and one pair of decorative end caps etc, complete all as specified and directed.

S&F in renewal PVC connection 450 mm long suitable for 15 mm GI pipe with two PTMT nuts and rubber washers complete all as specified and directed.

S&F 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe or for brass ferrule & fixed, complete all as specified and directed.

S&F in renewal bib taps, cast copper alloy, fancy type, chromium plated with long body with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in renewal 15 mm bore dia two way bib cock, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed to iron pipe or brass ferrule, complete all as specified and directed

S&F in renewal 15 mm bore stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed.

S&F in renewal 15 mm bore angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms) complete all as specified and directed.

S&F in renewal 20 mm bore stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed.

S&F in renewal shower rose, brass chromium plated, 80 mm size with swivel joint, screwed to iron pipe or for union of 15 mm dia, complete all as specified and directed.

S&F in renewal shower rose, brass chromium plated, 125 mm size with swivel joint, screwed to iron pipe or for union of 15 mm dia, complete all as specified and directed.

S&F in renewal vitreous china wash hand basin with pedestal, white, with flat back of size 550x400 mm, excluding chain and plug, taps and porcelain stopper but incl PVC waste pipe of 32 mm bore, one pair of 600 mm long cast iron brackets, complete all as specified and directed.

S&F in renewal 32mm dia waste coupling of PTMT (half or full threaded) minimum weight not less than 45 grams, complete all as specified and directed.

S&F in renewal 15 mm dia chromium plated brass centre hole basin mixer for mixing hot and cold water, fancy type, screwed down for iron pipe and fixed, complete all as specified.

S&F in renewal four way diverter for concealed fitting with built in non return valve with diverter handle and including wall mixer for 15mm bore iron pipe and fixed complete all as specified and directed.

S&F in renewal factory made pressed steel cupboard shutters alongwith frame, frame made of 1.25 mm thick PBI sheet and shutter made of 1.00 mm thick PBI sheet with 6 Nos 3.15 mm thick and 100 mm long steel hinges per shutter, godrej pattern locking arrangement with 12 mm dia vertical rod and lock with duplicate key & chrome finish handle, duly spray painted in factory with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, complete with fastener, hold fast etc as required at site, complete all as specified and directed. (Total width including frame shall be measured for payment purpose).

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 15 mm bore pipes complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 20 mm bore pipes complete all as specified and directed.

Refixing old steel tubing (obtained from item No 103.00 here-in-before) and connections in new or old position (walls, ceiling, floors, etc.) for 15 mm dia pipes with and including all new fittings complete all as specified and directed.

Refixing old steel tubing (obtained from item No 104.00 here-in-before) and connections in new or old position (walls, ceiling, floors, etc.) for 20 mm dia pipes with and including all new fittings complete all as specified and directed.

Supply, fixing, laying & testing 15 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

Supply, fixing, laying & testing 20 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

M & L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F in renewal vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest incl providing lime concrete bedding and connecting to flusing cistern, complete all as specified and directed.

S&F in renewal vitreous china wash down water closet pan (pedestal pattern) white including plastic seat cover white with flat bottom and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

M&L for PCC 1:5:10 type E-2, using 40 mm graded stone aggregate, as in foundation, filling, mass concreting etc as in sunken portion, complete all as specified and directed.

M&L for PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate, as in coving and like as in sunken portion, at radius 75mm complete all as specified and directed.

S&F in renewal PVC dual type flush cistern 10 Ltr capacity, valveless, syphonic action type, low level, white, with inlet, ball valve, float and handle & including brackets and superior quality PVC 32 mm bore flush pipe, complete all as specified and directed.

S&F in renewal 100mm cast iron sanitary connection socket to fit WC out-let, complete all as specified and directed.

S&F in renewal vitreous china bowl urinal flat back of size 465x355x265 mm, white with grating and union for discharge pipe, including one PVC waste pipe of 32 mm dia, one CP waste coupling of 32 mm dia and one cast iron 5 Ltr capacity automatic flushing cistern including brackets and 15 mm dia medium grade GI flush pipe of suitable length, complete all as specified and directed.

S&F in renewal 100 mm dia cast iron floor trap, with CP grating including jointing to waste pipe and fixed in cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) complete all as specified and directed.

S&F in renewal salt glazed stone ware gully traps, square or round mouthed, type 'P', size 150x150 mm, with and including bedding in PCC 1:5:10 type E1 using 20 mm graded stone aggregate, complete all as specified and directed.

S&F in renewal sink with draining board made of stainless steel 1mm thick with plugs, washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets of suitable angle iron, 32 mm dia superior quality PVC waste pipe and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in renewal stainless steel kitchen plate rack of size 600x600x225 mm, made of 0.80 mm thick stainless steel sheet with partition for small /large plates and fixed in position, design and pattern as approved by the GE, complete all as specified and directed.

Dismantling existing water storage tank of any description of capacity exc. 250 Ltr but n.exc. 500 Ltr, complete all as specified and directed.

Dismantling existing water storage tank of any description of capacity exc. 500 Ltr but n.exc. 1000 Ltr, complete all as specified and directed.

S&F in position rotational moulded polyethylene water storage tanks 500 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position, ISI marked complete all as specified in SSR Part I and as directed.

S&F in position rotational moulded polyethylene water storage tanks 1000 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position, ISI marked complete all as specified in SSR Part I and as directed.

S & F in renewal 100mm dia cast iron ‘P' or ‘S' trap, jointed in CM, complete all as specified and directed.

S&F in renewal PTMT alloy toilet cabinet with mirror of overall size 350x450 mm and fixed to wall complete all as specified and directed.

S&F in renewal stainless steel folding towel rack for bathroom / towel stand of size 600x330x40 mm, (weight not less 2.16 Kg) and fixed on wall, design and pattern as approved by the GE, complete all as specified and directed.

S&F in renewal plastic water closet seat cover, white, closed pattern with flat bottom and mild steel chromium plated hinging device, complete all as specified and directed.

S&F in renewal soap dish vitreous china white, approx size 160x160x90mm, embedded in wall, complete all as specified and directed.

S&F in renewal CP health faucet with 1 mtr long easy flex tube in chrome finish and wall hook, complete all as specified and directed.

M&L for 150 mm dia salt glazed stoneware drain pipes, laid in trenches and jointed in cement sand slurry in 1:1, complete all as specified and directed.

M&L PCC 1:4:8, type D-2 using 40 mm graded stone aggregate, as in concrete bed to drain pipes including packing under and haunching against the sides of 150 mm dia pipe, after they are laid and tested, complete all as specified and directed.

M/L for 50mm thick rough dressed stone slabs for manhole covers n.exc 2 mtr in length, punched dressed on face and along exposed edges, self faced on other side and sets and pointed in cement mortar 1:4 complete all as specified and directed.

S&F sand cast iron soil, waste and vent pipe 100 mm bore dia in any length with or without ears with cement joints laid in trenches or in floor and including dismantling of old u/s cast iron/existing pipes alongwith fittings and accessories complete all as specified and directed.

S&F sand cast iron soil, waste and vent pipe 75 mm bore dia in any length with or without ears with cement joints laid in trenches or in floor and including dismantling of old u/s cast iron/existing pipes alongwith fittings and accessories complete all as specified and directed.

S&F sand cast iron soil, waste and vent pipe 100 mm bore dia in any length with or without ears with cement joints and fixed to wall, ceiling or floors and including dismantling of old u/s cast iron/existing pipes alongwith fittings and accessories complete all as specified and directed.

S&F sand cast iron soil, waste and vent pipe 75 bore mm dia in any length with or without ears with cement joints and fixed to wall, ceiling or floors and including dismantling of old u/s cast iron/existing pipes alongwith fittings and accessories complete all as specified and directed.

S&F in renewal 100 mm dia CI bend (any radius), diminishing pieces or tapers (large dia measured) with oval access doors complete all as specified and directed.

S&F in renewal 75 mm dia CI bend (any radius), diminishing pieces or tapers (large dia measured) with oval access doors complete all as specified and directed.

S&F in renewal 100 mm dia CI branch pieces, single (equal or unequal) ordinary or inverted or with parallel branches, complete all as specified and directed.

S&F in renewal 75 mm dia CI branch pieces, single (equal or unequal) ordinary or inverted or with parallel branches, complete all as specified and directed.

S&F in renewal cast iron cowl 100 mm dia fixed with cement joint complete all as specified and directed.

S&F in renewal cast iron cowl 75 mm dia fixed with cement joint complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for reuse or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Dismantling unserviceable main switch/DBs incl wooden board and deposit to MES store yard including making good disturbed surface of wall complete all as specified and directed.

Taking down sub main wiring /XLPE cable of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surface, complete all as specified and directed.

M&L for Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface including providing wooden rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surfaces, complete all as specified and directed for the following: - One light/ceiling fan/exhaust fan/bell buzzer point controlled by one, one way switch of 5/6 Amps.

All as per item No 147.00 (here-in-before) but one 5 Pin, 5/6 amps socket outlet point on independent board, controlled by one, one way 5/6 Amp switch.

All as per item No 147.00 (here-in-before) but one 5 Pin, 5/6 amps socket outlet point on same board, controlled by one, one way 5/6 Amp switch.

M&L Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 2.5 Sqmm, with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable FRLS of size 2.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface for one socket outlet 15 amp on independent board including providing wooden rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surface, complete all as specified and directed.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, one way, ISI marked, complete all as specified & directed.

Supply and fixing switch socket combination, 5/6 and 15/16 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

Supply and fixing socket outlet, 5/6 Amps, 230 volt, five pin, flush type universal, complete all as specified and directed.

S&F in renewal stepped type electronic fan regulator, flush type, 230 volts AC, single pole, humming free, fixed on the existing phenolic laminated sheet, complete all as specified and directed.

S&F ceiling rose surface type PVC/Polycarbonate isolated body, 65x 50mm, 3 terminals, complete all as specified & directed.

S&F PVC/polycarbonate lamp holder, angular/batten type with back plate, ISI marked complete all as specified & directed.

S&F of wall mounted LED Tube light fittings, batten type with bipin holders, powder coated steel with & including retrofit 18 watt LED tube, internally prewired, complete all as specified and directed.

S&F of wall mounted LED Tube light fittings, batten type with integrated LED tube, powder coated steel with & including retrofit 11 watt LED tube, internally prewired, complete all as specified and directed.

S&F in renewal LED building security light fitting, 25 watt, pressure die cast aluminium housing with IP 66 deg of protection, complete with & including 0.55 m long street light bracket made of 32 mm bore GI light grade tubing including necessary clamps, nuts, bolts, washers etc, complete all as specified and directed.

S&F LED light fitting 30/36 Watt, 230 Volt AC, recessed mounting mirror optic luminiare with paralite louver complete, suitable for false/grid ceiling, complete with electronic driver, connector block and all accessories, duly prewired, including connecting up with three core twisted flexible copper conductor cable of size 14/.0060, complete all as specified and directed.

S&F surface mounted LED down light fitting 18/20 Watt, 230 Volt AC and all accessories & including connecting up with three core twisted flexible copper conductor cable of size 14/.0060, complete all as specified and directed.

S&F MCB, 6 to 32 Amps, Single Pole, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S&F MCB, 6 to 32 Amps, Single Pole & Neutral, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S & F, MCB TPN 63 Amps, 415 volts, four pole, B-curve, rupturing capacity 16KA conforming to IS-8828-1996, IEC-60898, complete, all as specified & directed.

S & F factory made MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 240 Volts SPN with 8 ways, Double door, complete all as specified and directed. Note for items of MCB DB - (1) The unit rate includes for cutting the brick walls to accommodate DB to make flush to wall. (2) The unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface.

S & F factory made MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, IP-43-IK09 protection grade, earth bar and Din rail, 415 Volts TPN with 4 ways, Double door, complete all as specified and directed.

S&F in renewal SPN enclosure with a two pin and earth plug and socket, complete with & including one double pole MCB of 20 amps, 230 Volts AC, complete all as specified and directed.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed FRLS multistranded copper conductor cable of size 6 Sqmm LT, 1100 volts grade, drawn through and including 20 mm dia PVC non metallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded FRLS copper conductor cable green colour as earth continuity conductor, complete all as specified & as directed. Note for srl item Nos. 169 & 170 :- Two runs of cable one run of earth wire and one run of PVC non metallic conduit of 20mm dia shall be measured as one run length. Cable required for connection to DBs shall deemed to be included and shall not be measured separately. Earth wire shall run inside the PVC conduit.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed FRLS multistranded copper conductor cable of size 4 Sqmm LT, 1100 volts grade, drawn through and including 20 mm dia PVC non metallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 4 sqmm single core multistranded FRLS copper conductor cable green colour as earth continuity conductor, complete all as specified & as directed.

S&F of sub main wiring with four runs of single core PVC insulated and unsheathed FRLS multistranded copper conductor cable of size 4 Sqmm LT, 1100 volts grade, drawn through and including 20 mm dia PVC non metallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 10 sqmm single core multistranded FRLS copper conductor cable green colour as earth continuity conductor, complete all as specified & as directed. Note :- Four runs of cable one run of earth wire and one run of PVC non metallic conduit of 20mm dia shall be measured as one run length. Cable required for connection to DBs shall deemed to be included and shall not be measured separately. Earth wire shall run inside the PVC conduit.

TARKESHWAR DASS CONSTRUCTION COMPANY

Ganesh Contruction

SK Guha and co

Pioneer Enterprises

S AND A ENGINEERS CONSTRUCTION CO

ANNAPURNA ENTERPRISES

M/S MOHINI ENTERPRISES