BLACK TOP ROAD FROM PWD ROAD TO LAVANYAMOY JB SCHOOL AT JURI RF VC UNDER RD DAMCHERRA SUB DIVISION DURING THE YEAR 2025-26.

Dismantling of Brick soling Dismantling of brick soling, stacking serviceable materials and unserviceable materials separately with all lifts and upto a lead of 500 m by manual means as per MoRD Technical Specification Clause 202.

Labour charge for Breaking of jhama bats/ jhama bricks/ 1st class bricks. Breaking of jhama bats/ jhama bricks /1st class bricks (including bigger lumps) into metal/chips /aggregates and stacking serviceable materials and unserviceable materials separately as per direction of the Engineer-in-charge with all lifts and upto a lead of 100 m. Required sizes for GSB (53 mm to 0.075 mm) as per MoRD Technical Specification Clause 401.

CONSTRUCTION OF SUBGRADE AND EARTHEN SHOULDERS Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site , spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per MoRD Technical Specification Clause 303.1.

Surface Drains Construction of unlined surface drains of average crosssectional area 0.40 sqm in ordinary soil to specified lines, grades, levels and dimensions. Excavated material to be used in embankment with a lift upto 3 m and lead of 50 m (average lead 25 m) as per MoRD Technical Specification Clause 307. Surface Drains in Ordinary Soil Mechanical Means

Road side Pucca Drains Construction of road side pucca drain with M10 (1:3:6 with jhama brick aggregate) to specified lines, grades, levels and dimensions as per approved design and MoRD Technical Specification Clause 307, 1606. Excavated material to be used in embankment at site. (including centering, shuttering, etc. but excluding reinforcement) Trapezoidal drain (top clear width 600 mm, bottom clear width 300 mm and clear depth of 400 mm) In Ordinary Soil

Granular Sub-base with Well Graded Material (using jhama brick aggregate) (Table 400.1) By Mix in Place Method Construction of granular sub-base by providing well graded material (Jhama Brick Aggregate, as per Table:- 400.1, Grading-I), spreading in uniform layers with tractor with attachments or motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, applying and brooming sand to fill up the interstices of coarse aggregate, watering and compacting with smooth wheel roller to achieve the desired density, complete as per MoRT&H Technical Specification Clause 401. For Grading- I Material (Jhama brick aggregate)

Wet Mix Macadam Providing, laying, spreading and compacting stone aggregates to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed materials by tipper to site, laying in uniform layers in sub-base/ base course on a well prepared sub-base and compacting with smooth wheel roller of three wheel 80-100 kN static roller to proper grade and camber, achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and as per MoRD Technical Specification Clause 406. By Mechanical Means with 1.00 km lead

Prime Coat Low porosity Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70- 1.00 kg/sqm using mechanical means as per MoRD Technical Specification Clause 502.

Tack Coat Providing and applying tack coat with bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per MoRD Technical Specification Clause 503.

Mix Seal Surfacing Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using Viscosity grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base , including mixing in a suitable plant, laying and rolling with a three wheel 80 - 100 KN static roller, finishing to required level and grades as per MoRD Technical Specification Clause 509. By Mechanical Means Type-B Bitumen of VG-30

Traffic Signs Retro-reflectorised Traffic Signs Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide MoRD technical specification Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and MoRD Technical Specification Clause 801. with III) 600 mm circular aluminium sheeting

v) with 600 x 450 mm rectangular aluminium sheeting

Kilometre Stone (with RCC M15 grade using jhama brick aggregate) Reinforced cement concrete M15 grade (using jhama brick aggregate) kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc. as per drawing and MoRD Technical Specification Clause 1703. ii) Ordinary Kilometre Stone(precast)

Road Markers/Road Stud with Lens Reflector Providing and fixing of road stud 100 x 100 mm die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling holes 30 mm upto a depth of 600 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS:873(Part 4) 1973.

Construction of RCC guide posts of 250 mm dia and total 600 mm long,(300 mm below GL) M15 grade (with jhama brick aggregate) cast-in-situ with 20 mm nominal size aggregate, true to line and grade, tolerance of vertical RCC posts not to exceed 1 in 500 as per drawing and MoRD Technical Specification Clause 1401.6. In Ordinary Soil

Road marking strips (retro-reflective) of specified shade/ colour using Hot Applied Thermoplastic material with Reflectorising Glass Beads on Bituminous Surface Providing and applying 2.5 mm thick thick road marking strips (retro-reflective) of specified shade/ colour using hot thermoplastic material including reflectorising glass beads @ 250 gms per sqm area by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater including cost of cleaning the road surface of all dirt, seals, oil, grease and foreign material etc, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes as per MoRT&H Technical Specification Clause 803.

Providing and Fixing 'Logo' of Project Providing and fixing of typical informatory sign board with Logo as per MORD specificationsanddrawing.ThreeMSPlatesof1.6mmthick,topandmiddleplatedulyweldedwithMSflatiron25mmx5mmsizeonbackonedges.ThelowerplatewillbeweldedwithMSangleironframeof25mmx25mmx5mm.Theangleironframeofthelowermostplateandflatironframeofmiddleplatewillbeweldedto2nos.75mmx75mmof12SWGsheettubespostsdulyembeddedincementconcreteM-15gradeblocksof450mmx450mmx600mm,600mmbelowgroundlevel.Thetopmostdiamondplatewillbeweldedtomiddleplateby47mmx47mmof12SWGsteelplatetube.AllM.S.willbestoveenameledonbothsides.Letteringandprintingarrows,borderetc.willbepaintedwithreadymixedsyntheticenamelpaintofsuperiorqualityinrequiredshadeandcolour.Allsectionsofframedpostsandsteeltubewillbepaintedwithprimerandtwocoatsofepoxypaintas per drawing Clause 1701 and Annexure 1700.1

Providing and Fixing 'Citizens' Information Board' of Project ProvidingandfixingoftypicalCitizens'InformationboardwithLogoasperMORDspecificationsanddrawing.TwoMSPlatesof2.0mmthick,dulyweldedwithMSflatiron50mmx5mmsizeonbackonedges.Theflatironframeofthelowermostplateandflatironframeofmiddleplatewillbeweldedto2nos.76.1mmOD(horizontal)and2Nos.76.1mmOD(Vertical)steeltubeposts{asperIS:1161-1979,MediumClass}dulyembeddedincementconcreteM-15gradeblocksof600mmx600mmx750mm,750mmbelowgroundlevel.AllM.S.willbestoveenameledonbothsides.Letteringandprintingarrows,borderetc.willbepaintedwithreadymixedsyntheticenamelpaintofsuperiorqualityinrequiredshadeandcolour.AllsectionsofframedpostsandsteeltubeandflatswillbepaintedwithprimerandtwocoatsofepoxypaintasperdrawingandspecificationClause170and Annexure 1700.1 Board 'A'

300 Excavation for Structures Without dewatering. Earthwork in excavation for structures as per drawing and MoRD technical specifications Clause 305.1 including setting out, construction of shoring & bracing, removal of stumps & other deleterious material and disposal upto a lead of 50 m, dressing of sides & bottom and backfilling in trenches with excavated suitable material. Ordinary Soil Upto 3 m depth

Sand Filling in foundation trenches as per drawing & MoRT&H technical specification clause 304.

Providing concrete for plain concrete (using jhama brick aggregate) in open foundations complete including formwork as per drawings & MoRD technical specifications Clauses 802, 803, 900, 1202 and 1203. (including centering, shuttering, staging etc. but excluding reinforcement) P.C.C grade M 10 (using jhama brick aggregate) Nominal mix 1:3:6

Providing concrete for plain concrete (using jhama brick aggregate) in open foundations complete including formwork as per drawings & MoRD technical specifications Clauses 802, 803, 900, 1202 and 1203. (including centering, shuttering, staging etc. but excluding reinforcement) P.C.C grade M 15 (using jhama brick aggregate) Nominal mix 1:2.5:5 (Hand mixing)

Backfilling behind abutment, wing wall & return wall complete as per drawings & MoRD technical specification Clause 1204.3.8. Sandy material

Plain/reinforced cement concrete in substructure complete including formwork as per drawings & MoRD technical specification Clauses 802, 804, 805, 806, 807, 900, 1202 & 1204. (including centering, shuttering, staging etc. but excluding reinforcement) R.C.C grade M-25 upto 5 m height

Supplying, fitting & placing Thermo-Mechanically treated bar/ Cold twisted deformed steel bar in substructure complete as per drawings & MoRD technical specification Clauses 1002, 1005, 1010 and 1202.

Providing weep holes in brick masonry/ stone masonry, plain/ reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe or uPVC pipe (110 mm OD of 6.0 kg/cm2 pressure) extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and MoRD technical specification clauses 614, 709, 1204.3.7.

Providing & laying filter media with jhama brick aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil & bigger size towards the wall & providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and MoRD technical specification clause 1204.3.8.

Providing & laying reinforced cement concrete in superstructure as per drawings & MoRD technical specifications Clauses 800, 900, 1205.4 & 1205.5 (including centering, shuttering, staging etc. but excluding reinforcement). R.C.C M 25 For height upto 5 m

Supplying, fitting, & placing Thermo-Mechanically treated bar/ Cold twisted deformed steel bar reinforcement in superstructure complete as per drawing & MoRD technical specifications Clauses 1002, 1010 & 1202.

Providing and fixing in position Drainage spouts complete as per drawing & MoRD technical specifications Clause 1209. Note:- Rate is inclusive of cost of steel grating and 1.00 m GI pipe of 100 mm dia.

Please Enable Macros to View BoQ information