Source level Augmentation of LWSS for group of villages in GP Bhuin and Bashona in tehsil Bhuntar Distt. Kullu

Amount

Cutting in earth work in all kind of soil containing spade work, jumper work, blasting work including decomposed soft and hard rock etc. complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Excavation in foundation and trenches up to all depths and in all classification of earth work such as pick work, jumper work, situated soil including bailing or pumping out water, blasting soft/ hard rock, chiseling /wedging of soft / hard rock where blasting is prohibited, in all lifts including trimming and dressing of sides, leveling of beds to correct grade including shoring, strutting, planking, timbering and dewatering wherever required. Stacking usable and unusable material /soil separately and after laying jointing and testing of pipes, returning the usable soil in 15cm layers by ramming and watering and then disposing of all surplus excavated soil/ unusable material as directed with in all leads/ lifts including restoration of un-metalled surfaces to its original conditions and including cost of diversion for traffic, night signal boards, fixing caution boards, crossing over trenches for access to houses, fencing etc. Complete in all respects within all leads and lifts as per direction of the Engineer-in-Charge.

Providing and laying cement concrete work using concrete mix of M-25 (1:1:2) graded stone aggregate 20mm nominal size and curing complete excluding the cost of the from work and reinforcement for reinfoced concrete work in:-

Foundation, footing, bases of columns & the like and the mass concrete.

In suspended floor roofs landing shelves & their support balconies, beams, girders bressumers cantilevers upto floor two level with in all leads and lifts.

Columns, pillars and posts etc.

Providing and laying cement concrete 1:6:12 ( 1 cement:6 sand:12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of formwork in foundation and plinth within all leads and lifts complete in all respect.

Random rubble masonry /polygonal rubber masonry coursed brought to course with hard stone of approved quality in level upto to with cement mortar 1:6 (1 cement : 6 sand) in Breast walls and R/walls

P/F angle iron door, window,clerestory window frame manufactured from steel iron section of 40x40x6mm, thickness including hinges jamb, lock jamb,beed and if rerquired angle threshold of mild steel angle 50x25mm welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including butt hinges 2.50mmthick with provision for locking arrangement and shock as specified and applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer-in-charge.

Cement concrete flooring 1:2:4(1 cement: 2 sand: 4graded stone agg. 20mm nominal size) laid in one layer finished with a floating of neat cement 40mm thick.

Providing and laying cement concrete 1:2:4 (1cement :2 Sand: 4 graded crushed stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work with in all leads and lifts as per the entire satisfaction & direction of the Engineer - in - Charge. in:-

In suspended floor roofs landing shelves & their support balconies, beams, girders bressumers cantilevers upto floor two level with in all leads and lifts.

In foundation and footing

Columns, pillars, posts and struts circular or curved unplan stepped soffits excluding landing.

Providing form work with steel plates 3.15mm thick welded with angle iron in frames 30x30x5mm so as to give a fair finish including centering ,shuttering, propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 meters and removal of the same for-in-situ reinforced concrete and plain concrete work in all leads and fifts:-

Foundation, footings basis of columns etc. and mass concrete.

Vertical surfaces such as wall(any thickness) partitions and the like including attached pilasters, buttresses, plinth and string courses and the like -

Flat surfaces such as soffits of suspended floors roofs landings and the like floors etc. up to 200 mm in thickness with in all leads and lifts.

Beam cantiliver girders and lintels Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding 1 Mtr. in depth in all heights from floor.

Columns, pillars, posts and struts circular or curved unplan stepped soffits excluding landing.

Sides of soffits of beams beam haunchings, cantileveres girder, breasumers and lintels not exceeding 1 meter in depth.

Tor steel reinforcement for RCC work including bending, binding & placing in position complete upto floor two level i.c cost of binding wire with in all leads and lifts as per the entire satisfaction & direction of the Engineer - in - Charge.

Providing &Fixing of fencing panels of Size 2.40 mtr x 1.20 mtr devided in Two Panels of 1.20 m X 1.20 M by fixing T iron at centre fitted with wire mesh 25 m.m x25mm welded to MS angle frame all around with MS flat cover and seven Nos. hold fasts including cutting welding painting with red oxide paint complete in all respect.

Steel work welded in built-up-sections trusses and framed work including cutting , hoisting fixing in position and applying a priming coat of ready red lead paint, In trussed and trussed purlins( Using MS sections ie Angles,Channels etc or MS pipes ) in buildings , including carriage of materials with in all leads and lifts as per direction of Engineer-in-charge.

Providing and laying cement concrete work 1:1.5:3 (1cement :1.5 sand: 3 graded crushed stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work with in all leads and lifts as per the entire satisfaction & direction of the Engineer - in - Charge. in: -

Foundation and plinth

Columns, pillars, posts and struts

Suspended floors, roofs, landings, shelves and their supports, balconies, beams, and girders, bressumers and cantilevers upto floor two level including all leads and lifts etc. complete in all respects.

Wall ( any thickness but not less than 0.10 mtrs. Thickness) including attached pillasters buttresses, plinth and string courses etc. from top of foundation level upto floor two level.

In beams

Providing and laying cement concrete 1:4:8 ( 1 cement:4 sand:8 graded stone aggregate 40 mm nominal size )and curing complete excluding cost of form work in foundation and plinth with in all leads and lifts complete in all respect and to the entire satisfation of the Engineer in Charge

Providing and laying cement concrete 1:5:10 (1 cement: 5 sand: 10 graded stone aggregate 40mm nominal size with 15% plum and curing complete excluding the cost of form work in retaining wall/ breast wall. The size of plum shall usually be 150mm to 300mm in all respect and as per direction and to the entire satisfaction of Engineer-in-charge.

Providing and laying cement concrete M-10 1:3:6(1 Cement :3 Sand : 6 graded stone aggregate 40mm nominal size)and curing complete excluding the cost of form work in foundation and plinth including all carriage of materials upto all leads and lifts complete in all respects.

Providing in RCC work smooth finishing of the exposed surface with cemetn mortor 1:3 (1 Cement: 3 Sand) complete in all respect within all leads and lifts.

Providing and fixing SFRC manhole cover cover and frame confirming to IS-12592-Part-II 1990 with latest amendments (560 mm dia) medium duty.

Providing and fixing locking arrangement complete in all leads and lifts.

Laying , jointing & fixing Inlet, outlet & Scour pipe (LG) in trenches including within all leads and lifts as per the direction of Engineer-in-Charge. (L.R.)

Providing and Fixing Cast Iron Sluice Valve of dia mentioned below class PN 1.00 with Flange Table - 5 conforming to IS-9001-2000 or latest with upto date ammendments of Pelican / Kirloskar / Kilburn make including cost of welding of companion flanges, nut & bolts, rubber insertions washers (gasket) etc. as per specifications complete in all respect in all leads and lifts and to the entire satisfaction of Engineer - in - Charge.

100 mm dia

Providing and placing in horizontal layers filtering media duly graded, screened,cleaned and washed as specified :

Top layer, Fine sand( Eff. Size 0.20mm to 0.40 and uniformity co-efficient 2.00 to 3.00).

Second layer, Coarse sand, 3mm - 6mm

Third layer : Bajri 6mm to 20 mm.

Fourth layer : Bajri 20mm to 25 mm

Bottom layer : Broken stone 50mm to 75 mm.

Providing & placing Precast Concrete Block in CC 1:2:4 ( I cement :2 sand ;4 graded stone aggrigate 20 mm nominal size)over X Drain

Brick work using common burnt clay building bricks in foundation and plinth in cement mortor 1:6 (1 cement: 6 sand), Ist class bricks

Brick work using common burnt clay building bricks in superstructure above G.L. to 1st floor level in cement mortar 1:6 ( 1Cement, 6 Sand ) of 1st class bricks complete in all respect with in all leads and lifts.

Providing wood work in frames of doors, windows, clearstory, windows and other frames wrought framed and fixed in position: 2nd class deodar wood

Providing and fixing glazed and pannelled,glazed or pannelled shutters for doors, windows & clerestory windows Ic bright finished black enamelled iron butt hinges with necessary screws.(a) 40 mm thick 2nd class deodar wood with in all leads and liftscomplete in all respect.

Half brick work using common burnt clay building bricks in superstructure above 1st floor level in cement mortar 1:4( 1Cement, 4 Sand ) of 1st class bricks complete in all respect with in all leads and lifts.

Pointing on brick work with cement mortar 1:4 ( 1 cement, 4 sand ) with in all leads and lifts complete in all respect. Raised and cut

6 mm thick cement plaster to ceiling in C.M.1:3 (1Cement,3 sand) with in all leads and lifts complete in all respect.

15 mm thick cement plaster in single coat on rough side of brick stone concrete walls for interior plastering up to floor -2 level including arrisses,internal rounded angles,chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth with in all leads and lifts in C.M 1:6 ( 1 cement,6 sand )

20 mm thick cement plaster in single coat on rough side of brickstoneconcrete walls for interior plastering up to floor -2 level including arrisses,internal rounded angles,chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth with in all leads and lifts in C.M 1:6 ( 1 cement,6 sand )

Providing and fixing MS grills of required pattern in wooden frames of window etc with M.S flat square or round bars with round headed bolts and nuts or by screw with in all leads and lifts complete in all respect.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of IS gauge specification 8 S.G with wire of dia 0.56 mm for doors,windows ic bright finished black enamelled iron butt hinges with necessary screws 30 mm thick of 2nd class deodar wood with in all leads and lifts complete in all respect.

Precast terrazzo tiles hydraulic compressed 20mm thick marble chips of specified sizes laid in floors treads of steps and landings on a bed of 25mm average thickness of cement mortar 1:6 (1cement :6sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) i/c rubbing and polishing complete with tiles of

Boulder filling behind retaining wall under floor with in all leads and lifts complete in all respect.

Providing 40X3 mm flat iron hold fast 40 cms long including fixing to frame with 10 mm diameter bolts nuts and wooden plugs and embedding in cement concrete block 30X10X15 cm. 1:3:6 ( 1 cement ,3 sand,6 graded stone aggregate 20 mm nominal size complete in all respect with all leads and lifts.

White washing with lime on un-decorated wall surfaces ( two coats ) to give an even shade including throughly brooming the surface to remove all,dirt,dust,mortar and other foreign matters with in all leads and lifts complete in all respect.

Distempering with oil Bound distemper of approved brand and manufacturer ( Two Coats ) and of required shade on un-decorated wall surfaces to give an even shade over and including priming coat of whiting after throughly brushing the surface free from mortar and other foreign matters with in all leads and lifts complete in all respect.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces(two coats)to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials.

Providing and fixing MS sliding door bolts anodised colour and shade with nuts and screws complete in all respect. ( 300X16 mm )

Providing and fixing MS tower bolts ( Barrel type ) anodised transparent or died to required shade with necessary screws complete in all respect.

Providing and fixing MS handles anodised,transparent or died to required shade with necessary screws complete in all respect. 125 mm

Providing and fixing to wall ceiling and floor galvanised mild steel tubes ( MG) including fitting and clamps including making good the wall ceiling and floor complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge ..

Applying priming coat on new wood and wood based surfaces with ready mixed paint and brushing to give an even shade including cleaning of all dirt, dust and other foreign matter with in all leads and lifts complete in all respect.

Painting two coats excluding priming coat on new wood and wood based surfaces with ready mixed paint and brushing to give an even shade including cleaning of all dirt, dust and other foreign matter with in all leads and lifts complete in all respect.

Providing plinth protection 50mm thick in cement concete1:3:6 (1 cement :3 sand :6 graded stone agg. 20mm nominal size.

Providing under layer for plinth protection of 75mm thick unconsolidated ) bed dry brick/ stone aggregate 40mm nominal size will tammed and consolidated and grouted with fine sand including preparation of ground.

Providing and placing (at all heights) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes including all fittings and float valve excluding the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid ISI license ]. 500 Ltrs. capacity

Providing and fixing vitreous china wash, down water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement: 1 sand). Seat and cover to be measured and paid for seperately. Anglo Indian Universal closet.

Providing and fixing plastic seat and cover for wash down water closet with C.P. brass hinges and rubber buffers: White plastic seat and cover, solid type.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.10 litre capacity - White

Providing and fixing PVC / G.I. inlet connection for flush pipe connecting with W.C. pan.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. brass angle valve of standard design and of approved make, 15mm nominal bore.

Providing and fixing C.P. water jet including connection pipe with check nut complete in all respect

Providing and fixing PVC pipes of 10 Kg f/Sq.cm working pressure including fittings as per requirement at site complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .110 mm OD

1 Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required.Group C

Wiring for circuit / sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping along with 1 No.HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2x1.5 Sq. mm.

2x4.0 Sq. mm.

(a)Supplying and fixing following rating Piano-type switch /socket on the existing switch box / cover including connections etc. as required 1) S.P. 5/6 Amp one way switch , Piano type.

(b)Supplying and fixing following rating Piano-type switch /socket on the existing switch box / cover including connections etc 1) 5 Pin 5/6 Amp Socket outlet, Porcelain base/piano type.

(a)Supplying and fixing following rating Piano-type switch /socket on the existing switch box / cover including connections etc. 1) S.P. 15/16 Amp one way switch, porcelain base/piano type.

(b)Supplying and fixing following rating Piano-type switch /socket on the existing switch box / cover including connections etc. as required. 1) 6 pin 15/16 Amp socket outlet , porcelain base/ pianto type.

Supplying & fixing PVC boxes of following sizes (nominal size) on surface or in recess suitable for fixing phenolic laminated sheet cover in front including painting etc. as required:-

180mmx100x60mm

250x200x60mm. Deep

Supplying and fixing ceiling rose on the existing junction box /wooden block including connections etc. as required.

Supplying and fixing plain pendent with 16/0.20 mm twin twisted, flexible, PVC insulated, cotton braided, copper cable and bakelite pendent holder including connections etc. as required:-

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required:-

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wireset, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:- 1) Single Door 10 way.

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. (63 Amps. Cat-A.) Single pole

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required:- 1) Ceiling fan 1200 mm sweep, Category-A

Providing and fixing ultra slim decorative extruded box fixture with domestic electronic ballast, snap-on installers, suitable for 28 watt FTL (T5), complete with all accessories (including one No. T-5 Tube), connections, testing and commissioning etc. as required.

1 x28 watt-FTL(T5) (Category-A)

Providing and fixing following type of surface mounting decorative mirror optics luminaire with powder coated CRCA sheet steel housing, low glare aluminium mirror reflector, prewired with 110 V starter & 36/40 w copper ballast for housing CFL (but excluding the cost of CFL), complete with all accessories, connections, testing and commissioning etc. as required.

3 x36 watt-CFL (Category-A)

Providing and fixing double core service wire 6mm thick.

Providing , laying,jointing ( by way of circumfrential butt welded joints by electrical arc welding ) and testing of MSERW pipe of following dia meters confirming to ISO 3183-2007, steel grade -A (latest with upto date amendments) having wall thickness as specified below with bevelled ends and capable of withstanding required test pressure in a random length of 4 to 7 meters, including manufacturing reducers/ tapers , all short pieces, bends etc. as per site requirement made from parent tubes . The laying of pipe will include all operations such as cutting, welding, jointing, fabrication of bends, tees etc. including lowering and laying in excavated trenches to ensure required level including flushing, cleaning and hydraulic testing complete in all respects to the satisfaction of the Engineer in charge. The fabricated bends shall have three or four cuts having its radius not less than five times the dia of pipe. The pipes shall be factory galvanized (zinc coating both inside and outside) as per relevant IS standards and the damaged portion of the pipes and specials made form the parent tube during welding or otherwise shall be provided anticorrosive treatment by applying two coats of anticorrosive bituminous paint over a priming coat as per AWWA specifications C-203-1978. The welding electrodes shall be as per IS 814 of Advani Oerlikon/ L&T or ISI marked make. The rates also includes entire carriage of material, flushing, cleaning & hydraulic testing complete to the best satisfaction & direction of Engineer in charge with in all leads and lifts. (Earth work in trenches will be measured and paid for separately).

Stage-1 RD 0 to 700 = 700 Rmt 100 mm dia MSERW pipe Wall thickness 4.80, Length of butt welding @95% = 665 Rmt)

Laying,jointing ( by way of circumfrential butt welded joints by electrical arc welding ) and testing of Galvanised mild steel tubes (GI Pipes) of following dia meters confirming to BIS 1239-2001 (latest with upto date amendments) having wall thickness as per code with bevelled / plain ends in a random length of 4 to 7 meters, including manufacturing reducers/ tapers , all short pieces, bends etc. as per site requirement made from parent tubes . The laying of pipe will include all operation such as cutting, welding, jointing, fabrication of bends, tees etc. including lowering and laying in excavated trenches to ensure required level including flushing, cleaning and hydraulic testing complete in all respects to the satisfaction of the Engineer in charge. The fabricated bends shall have three or four cuts having its radius not less than five times the dia of pipe. The damaged portion of the pipes and specials made form the parent tube during welding or otherwise shall be provided anticorrosive treatment by applying two coats of anticorrosive bituminous paint over a priming coat as per AWWA specifications C-203-1978. The welding electrodes shall be as per IS 814 of Advani Oerlikon/ L&T or ISI marked make. The rates also includes entire carriage of material, flushing, cleaning & hydraulic testing complete to the best satisfaction & direction of Engineer in charge with in all leads and lifts. (Earth work in trenches will be measured and paid for separately).

Stage-1 From RD 700 to 2700 = 2000 Rmt 100 mm dia GI pipe (M-Class) Wall thickness 4.80, Length of butt welding @95% = 1900 Rmt)

Providing , laying, fixing, jointing and testing in trenches MSERW pipe of following dia meters confirming to ISO 3183-2007, steel grade -A (latest with upto date amendments) having wall thickness as specified below with plain end and capable of withstanding required test pressure in random length of 4 to 7 meters, including specials, short pieces, bends, reducers, tees etc. made from parent tube, provinding and welding of MS flanges detailed as below. The MS flanges shall confirm to BIS 6392-1971 (with latest up to date amendments) duly welded in two layers (two inner and two outer) with pipes at both ends as per relevant BIS standards along with nuts and bolts of required sizes, 3mm thick compressed asbestos fiber/synthetic rubber gaskets confirming to relevant BIS standards. The laying of pipe will include all operation such as cutting, welding, jointing, providing & fixing of MS flanges, fabrication of bends, tees etc. including lowering and laying in excavated trenches to ensure required level including flushing, cleaning and hydraulic testing complete in all respects to the satisfaction of the Engineer in charge. The fabricated bends shall have three or four cuts having its radius not less than five times the dia of pipe. The pipes shall be factory galvanized (zinc coating both inside and outside) as per relevant IS standards and the damaged portion of the pipes and specials made form the parent tube during welding or otherwise shall be provided anticorrosive treatment by applying two coats of anticorrosive bituminous paint over a priming coat as per AWWA specifications C-203-1978. The welding electrodes shall be as per IS 814 of Advani Oerlikon/ L&T or ISI marked make. The rates also includes entire carriage of material, flushing, cleaning & hydraulic testing complete to the best satisfaction & directin of Engineer in charge with in all leads and lifts. (Earth work in trenches will be measured and paid for separately).

Stage-1 From RD 0 to 700 = 700 Rmt 100 mm dia MSERW pipe Flange Table -34 Wall thickness 4.80, Length of flange = joint 95% = 35 Rmt)

Laying, jointing and testing in trenches to be levelled to grades, GI flanged pipes of following diameter confirming to IS:1239-1990( Part-II) having minimum wall thickness as per IS code and class of pipes specified below, provided and jointed with flanges conforming to tables as specified below of BIS 6392-1971 welded at both ends according to relevant BIS standards and detailed specifications and provided with nut & bolts of required sizes, 3mm thick compressed asbestos fiber jointing gasket / synthetic rubber gasket confirming to relevant BIS codes including all kinds of flanged short pieces, bends, tees & other specials etc made from parent tubes & welded with flanges of tables as applicable for the particular reach as per site conditions including flushing, cleaning & hydraulic testing as per directions of Engineer-in-charge.

Submersible stage Booster Stage -II From RD 0 to 170 = 170 Rmt 80 mm dia GI (M-Class) pipe wall thickness 4.80 Flange Table-17 Flange joints @100 = 170 Rmt

Booster Stage -I From RD 0 to 100 = 100 Rmt 80 mm dia GI (M-Class) pipe wall thickness 4.80 Flange Table-17 Flange joints @100% = 100 Rmt

Dug well From RD 0 to 50 = 50 Rmt 80 mm dia GI (M-Class) pipe wall thickness 4.80 Flange Table-17 Flange joints @100% = 50 Rmt

Monoblock From RD 0 to 70 = 70 Rmt 80 mm dia GI (M-Class) pipe wall thickness 4.80 Flange Table-17 Flange joints @100% = 70 Rmt

Centrifugal Main stage From RD 700 to 1800 = 800 Rmt 100 mm dia GI (M-Class) pipe wall thickness 4.80 Flange Table-28 Flange joints @5%= 40 Rmt

From RD 1500 to 2700 = 1200 Rmt 100 mm dia GI (M-Class) pipe wall thickness 4.80 Flange Table-17 Flange joints @5%= 60 Rmt

Monoblock Pump for Booster-I :- Providing & fixing horizontal Monoblock pump set of Kirloskar of any other approved make conforming to relevant IS with upto date ammendments having clute casing impellers of cast iron Gr FG 200 carbon steel shaft Fr 40 suitabele for operation on 415(+/-) 10% volts 3 phase AC supply. The power of electrial motor shoud be atlest 10 % in access of the maximum power required by the pump in the operation range of (+10%( and (-15 %) of the duty point head. The motor /mototy conforming to minimum IE 2 norms IS-12615/2011 with upto date ammendements it should include cost of bearing nuts, bolts and poiting etc. The pump set should be capable to perform the following duties.

Discharge (Q) pump 3.73 LPS

Total Dymanic Head 8.14 meter

Rising main Lenght 70.00 meter

Dia 80 mm

Level at highest discharg point 1078 meter

Level pump shaft meter 1075 meter

LWL in well (H) 1074 meter

Pumping hours 8 hours

Suction lift 1 (+ve)

Discharge head 8.14 meter

Residual head 3.00 meter

Static head 3.00 meter

Altitude of installation above MSL 1075 meter

Temperature 20 degree centigrate

Characterstics head of water Clear water with turbodity upto 50PPM Pumps spesifications :- Make Model Nos of stages Material manufactures certificate to be appended Head Discharge Motor rating (KW) Speed BHP avsirve Effeicency NPSH(K)

Providing control panel as per KSB specifications and having protection of motor on occurance of faults { Triping on occurance of fault(s) i.e. Moisture, high motor temperature, dry running, reverse rotation, Single phasing, voltage imbalance, overload and short circuit } and indiation thereof by glowing fault lamp ; for motors above 30 KW another protection of Mechanical seal failure shall also be provided in addition to above protections; fitted with following components:-

Powder coated steel sheet fabricate enclosure of suitable size to accommodate the following accessories:-

Shnider /L&T/Havells/Standard make MCCB in MAINS on incomer side

Shnider/ Siemens make phase indicating lamps

Logestic or similar superior make 300VA transformer

AUTO/MANUAL switch Salzer/L&T/kaycee make

3 Nos CONTACTORS of Spercher+ Schuh /L&T/Schnider /BCH/Siemens make, for star delta starting

Over load relay

STAR-DELTA TIMER ( for pumpset above 7.5HP)

SINGLE PHASING PREVENTOR

ON/TRIP INDICATING LIGHTS Schnider/ Siemens /L&T make

CONTROL MCB Schnider/ Havells/Standard/Siemens/ Legrand make

PUSH BT. Schnider/Siemens/L&T make

TERMINALS Phonix make

RCCB of Legrand/Siemens/Havells / L&T/ Standard make

Hour run meter of CE/Kaycee make

Providing Double flanged Leader / Pelican /Kirloskar make Cast iron Sluice Valve in delivery side conf. to Class IS 780 PN 1.0; one size higher than delivery outlet size of pump (suitable dia)

Providing Double flanged Leader / Pelican /Kirloskar make Cast iron Swing check type Reflux Valve in delivery side conf. to Class IS 5312 PN 1.0; one size higher than delivery outlet size of pump (suitable dia)

Prov. and laying PVC Insulated armoured copper conductor cable Havells/Gloster/Khaitan make of suitable size and suitable for motor offered under item No 63complete with flexible pipe and couplers from HPSEB meter to Panel, switch, starter complete job, The type and size shall be subject to approval of Electrical authorities and in case of its non acceptance the same shall be replaced free of cost by the tenderer

Supply side : _______ mm^2 Motor side : ______ mm^2

Prov. and laying PVC Insulated round copper conductor cable of suitable size suitable for motor offered under item No 63complete having suitable cores to fulfill requirement of star delta starter and protection/ controls from panel to motor sqm mm

10 Mtr cable per set shall be supplied free of cost ( cost inclusive in cost of pumpset ) additional length shall be measured to and paid seperately. Cost to be quoted for additional length over and above free cable of 10 Mtr/ pumpset

Providing 100 mm dial pressure guage of Fiebig/Bourden make having range 0-7 Kg/cm^2 with copper tubing, stop cock and allied access.as per IS 3624 - 1987 latest with up to date amendments

Supply of cable for water level guard

Supply of supporting clamps

Supply of cable clips of required size

Erection of all equipments from Sr No 77 to 87 including cost of tee's bends, tappers and any other required fitting as per site condition and directions of engineer in charge.

Pumping machinery Booster -1 (Bore 1) Supply of submersible pumping set of (KSB/Kalama /Kirloskar/Johnston/ Cromption/BS) make conforming to BIS; 8034-1976 latest suitable for lifting clear water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacurer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendments) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps,cable clips & depth gauge etc. The power of electrial motor shoud be atlest 10 % in access of the maximum power required by the pump in the operation range of (+10%( and (-15 %) of the duty point head. The motor /motor conforming to minimum IE 2 norms IS-12615/2011 with upto date ammendements it should include cost of bearing nuts, bolts and poiting etc. The pump set should be capable to perform the following duties.

Discharge (Q) pump 3.39 LPS for each

Total Dymanic Head 14.24 meter

Rising main Lenght 170.00 meter

Dia 80 mm

Level at highest discharge point 1076 meter

Level pump shaft meter 1068 meter

LWL in bore well (H) 1067 meter

Pumping hours 8 hours

Suction lift 1 (+ve)

Discharge head 14.24 meter

Residual head 3.00 neter

Static head 800 meter

Altitude of installation above MSL 1068 meter

Temperature 20 degree centigrate

Characterstics of water Clear water with turbodity upto 50 PPM Pumps spesifications Make Model Nos of stages Material manufactures certificate to be appended Head Discharge Motor rating (KW) Speed BHP avsorve Effeicency NPSH(K)

Providing control panel as per KSB specifications and having protection of motor on occurance of faults { Triping on occurance of fault(s) i.e. Moisture, high motor temperature, dry running, reverse rotation, Single phasing, voltage imbalance, overload and short circuit } and indiation thereof by glowing fault lamp ; for motors above 30 KW another protection of Mechanical seal failure shall also be provided in addition to above protections; fitted with following components:-

Powder coated steel sheet fabricate enclosure of suitable size to accommodate the following accessories:-

Shnider /L&T/Havells/Standard make MCCB in MAINS on incomer side

Shnider/ Siemens make phase indicating lamps

Logestic or similar superior make 300VA transformer

AUTO/MANUAL switch Salzer/L&T/kaycee make

3 Nos CONTACTORS of Spercher+ Schuh /L&T/Schnider /BCH/Siemens make, for star delta starting

Over load relay

STAR-DELTA TIMER ( for pumpset above 7.5HP)

SINGLE PHASING PREVENTOR

ON/TRIP INDICATING LIGHTS Schnider/ Siemens /L&T make

CONTROL MCB Schnider/ Havells/Standard/Siemens/ Legrand make

PUSH BT. Schnider/Siemens/L&T make

TERMINALS Phonix make

RCCB of Legrand/Siemens/Havells / L&T/ Standard make

Hour run meter of CE/Kaycee make

Providing Double flanged Leader / Pelican /Kirloskar make Cast iron Sluice Valve in delivery side conf. to Class IS 780 PN 1.0; one size higher than delivery outlet size of pump (suitable dia)

Providing Double flanged Leader / Pelican /Kirloskar make Cast iron Swing check type Reflux Valve in delivery side conf. to Class IS 5312 PN 1.0; one size higher than delivery outlet size of pump (suitable dia)

Prov. and laying PVC Insulated armoured copper conductor cable Havells/Gloster/Khaitan make of suitable size and suitable for motor offered under item No 63complete with flexible pipe and couplers from HPSEB meter to Panel, switch, starter complete job, The type and size shall be subject to approval of Electrical authorities and in case of its non acceptance the same shall be replaced free of cost by the tenderer

Supply side : _______ mm^2 Motor side : ______ mm^2

Prov. and laying PVC Insulated round copper conductor cable of suitable size suitable for motor offered under item No 63complete having suitable cores to fulfill requirement of star delta starter and protection/ controls from panel to motor sqm mm

10 Mtr cable per set shall be supplied free of cost ( cost inclusive in cost of pumpset ) additional length shall be measured to and paid seperately. Cost to be quoted for additional length over and above free cable of 10 Mtr/ pumpset

Providing 100 mm dial pressure guage of Fiebig/Bourden make having range 0-7 Kg/cm^2 with copper tubing, stop cock and allied access.as per IS 3624 - 1987 latest with up to date amendments

Supply of cable for water level guard

Supply of supporting clamps

Supply of cable clips of required size

Erection of all equipments from Sr No 89 to 99 including cost of tee's bends, tappers and any other required fitting as per site condition and directions of engineer in charge.

Booster -II (Bore II) Supply of submersible pumping set of (KSB/Kalama /Kirloskar/Johnston/ Cromption/BS) make conforming to BIS; 8034-1976 latest suitable for lifting clear water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacurer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendments) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps,cable clips & depth gauge etc. The power of electrial motor shoud be atlest 10 % in access of the maximum power required by the pump in the operation range of (+10%( and (-15 %) of the duty point head. The motor /motor conforming to minimum IE 2 norms IS-12615/2011 with upto date ammendements it should include cost of bearing nuts, bolts and poiting etc. The pump set should be capable to perform the following duties.

Discharge (Q) pump 3.39 LPS for each

Total Dymanic Head 13.33 meter

Rising main Lenght 100.00 meter

Dia 80 mm

Level at highest discharge point 1076 meter

Level pump shaft meter 1068 meter

LWL in bore well (H) 1067 meter

Pumping hours 8 hours

Suction lift 1 (+ve)

Discharge head 12.33 meter

Residual head 3.00 meter

Static head 8.00 meter

Altitude of installation above MSL 1068 meter

Temperature 20 degree centigrate

Characterstics of water Clear water with turbodity upto 50 PPM Pumps spesifications Make Model Nos of stages Material manufactures certificate to be appended Head Discharge Motor rating (KW) Speed BHP avsorve Effeicency NPSH(K)

Providing control panel as per KSB specifications and having protection of motor on occurance of faults { Triping on occurance of fault(s) i.e. Moisture, high motor temperature, dry running, reverse rotation, Single phasing, voltage imbalance, overload and short circuit } and indiation thereof by glowing fault lamp ; for motors above 30 KW another protection of Mechanical seal failure shall also be provided in addition to above protections; fitted with following components:-

Powder coated steel sheet fabricate enclosure of suitable size to accommodate the following accessories:-

Shnider /L&T/Havells/Standard make MCCB in MAINS on incomer side

Shnider/ Siemens make phase indicating lamps

Logestic or similar superior make 300VA transformer

AUTO/MANUAL switch Salzer/L&T/kaycee make

3 Nos CONTACTORS of Spercher+ Schuh /L&T/Schnider /BCH/Siemens make, for star delta starting

Over load relay

STAR-DELTA TIMER ( for pumpset above 7.5HP)

SINGLE PHASING PREVENTOR

ON/TRIP INDICATING LIGHTS Schnider/ Siemens /L&T make

CONTROL MCB Schnider/ Havells/Standard/Siemens/ Legrand make

PUSH BT. Schnider/Siemens/L&T make

TERMINALS Phonix make

RCCB of Legrand/Siemens/Havells / L&T/ Standard make

Hour run meter of CE/Kaycee make

Providing Double flanged Leader / Pelican /Kirloskar make Cast iron Sluice Valve in delivery side conf. to Class IS 780 PN 1.0; one size higher than delivery outlet size of pump (suitable dia)

Providing Double flanged Leader / Pelican /Kirloskar make Cast iron Swing check type Reflux Valve in delivery side conf. to Class IS 5312 PN 1.0; one size higher than delivery outlet size of pump (suitable dia)

Prov. and laying PVC Insulated armoured copper conductor cable Havells/Gloster/Khaitan make of suitable size and suitable for motor offered under item No 63complete with flexible pipe and couplers from HPSEB meter to Panel, switch, starter complete job, The type and size shall be subject to approval of Electrical authorities and in case of its non acceptance the same shall be replaced free of cost by the tenderer

Supply side : _______ mm^2 Motor side : ______ mm^2

Prov. and laying PVC Insulated round copper conductor cable of suitable size suitable for motor offered under item No 63complete having suitable cores to fulfill requirement of star delta starter and protection/ controls from panel to motor sqm mm

10 Mtr cable per set shall be supplied free of cost ( cost inclusive in cost of pumpset ) additional length shall be measured to and paid seperately. Cost to be quoted for additional length over and above free cable of 10 Mtr/ pumpset

Providing 100 mm dial pressure guage of Fiebig/Bourden make having range 0-7 Kg/cm^2 with copper tubing, stop cock and allied access.as per IS 3624 - 1987 latest with up to date amendments

Supply of cable for water level guard

Supply of supporting clamps

Supply of cable clips of required size

Erection of all equipments from Sr No 101 to 111including cost of tee's bends, tappers and any other required fitting as per site condition and directions of engineer in charge.

Dug well Supply of submersible pumping set of (KSB/Kalama /Kirloskar/Johnston/ Cromption/BS) make conforming to BIS; 8034-1976 latest suitable for lifting clear water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacurer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendments) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps,cable clips & depth gauge etc. The power of electrial motor shoud be atlest 10 % in access of the maximum power required by the pump in the operation range of (+10%( and (-15 %) of the duty point head. The motor /motor conforming to minimum IE 2 norms IS-12615/2011 with upto date ammendements it should include cost of bearing nuts, bolts and poiting etc. The pump set should be capable to perform the following duties.

Discharge (Q) pump 4.67 LPS for each

Total Dymanic Head 13.24 meter

Rising main Lenght 50.00 meter

Dia 80 mm

Level at highest discharge point 1076 meter

Level pump shaft meter 1068 meter

LWL in bore well (H) 1067 meter

Pumping hours 8 hours

Suction lift 1 (+ve)

Discharge head 13.24 meter

Residual head 3.00 meter

Static head 8.00 meter

Altitude of installation above MSL 1068 meter

Teperature 20 degree centigrate

Characterstics of water Clear water with turbodity upto 50 PPM Pumps spesifications Make Model Nos of stages Material manufactures certificate to be appended Head Discharge Motor rating (KW) Speed BHP avsorve Effeicency NPSH(K)

Providing control panel as per KSB specifications and having protection of motor on occurance of faults { Triping on occurance of fault(s) i.e. Moisture, high motor temperature, dry running, reverse rotation, Single phasing, voltage imbalance, overload and short circuit } and indiation thereof by glowing fault lamp ; for motors above 30 KW another protection of Mechanical seal failure shall also be provided in addition to above protections; fitted with following components:-

Powder coated steel sheet fabricate enclosure of suitable size to accommodate the following accessories:-

Shnider /L&T/Havells/Standard make MCCB in MAINS on incomer side

Shnider/ Siemens make phase indicating lamps

Logestic or similar superior make 300VA transformer

AUTO/MANUAL switch Salzer/L&T/kaycee make

3 Nos CONTACTORS of Spercher+ Schuh /L&T/Schnider /BCH/Siemens make, for star delta starting

Over load relay

STAR-DELTA TIMER ( for pumpset above 7.5HP)

SINGLE PHASING PREVENTOR

ON/TRIP INDICATING LIGHTS Schnider/ Siemens /L&T make

CONTROL MCB Schnider/ Havells/Standard/Siemens/ Legrand make

PUSH BT. Schnider/Siemens/L&T make

TERMINALS Phonix make

RCCB of Legrand/Siemens/Havells / L&T/ Standard make

Hour run meter of CE/Kaycee make

Providing Double flanged Leader / Pelican /Kirloskar make Cast iron Sluice Valve in delivery side conf. to Class IS 780 PN 1.0; one size higher than delivery outlet size of pump (suitable dia)

Providing Double flanged Leader / Pelican /Kirloskar make Cast iron Swing check type Reflux Valve in delivery side conf. to Class IS 5312 PN 1.0; one size higher than delivery outlet size of pump (suitable dia)

Prov. and laying PVC Insulated armoured copper conductor cable Havells/Gloster/Khaitan make of suitable size and suitable for motor offered under item No 63complete with flexible pipe and couplers from HPSEB meter to Panel, switch, starter complete job, The type and size shall be subject to approval of Electrical authorities and in case of its non acceptance the same shall be replaced free of cost by the tenderer

Supply side : _______ mm^2 Motor side : ______ mm^2

Prov. and laying PVC Insulated round copper conductor cable of suitable size suitable for motor offered under item No 63complete having suitable cores to fulfill requirement of star delta starter and protection/ controls from panel to motor sqm mm

10 Mtr cable per set shall be supplied free of cost ( cost inclusive in cost of pumpset ) additional length shall be measured to and paid seperately. Cost to be quoted for additional length over and above free cable of 10 Mtr/ pumpset

Providing 100 mm dial pressure guage of Fiebig/Bourden make having range 0-7 Kg/cm^2 with copper tubing, stop cock and allied access.as per IS 3624 - 1987 latest with up to date amendments

Supply of cable for water level guard

Supply of supporting clamps

Supply of cable clips of required size

Erection of all equipments from Sr No 113 to 123 including cost of tee's bends, tappers and any other required fitting as per site condition and directions of engineer in charge.

Main stage Supply, erection, testing & commissioning of horizontal spindle,horizontal split casing,radial split Single, /Multistages centrifugal pumps or combination of pumps, in series/parallel of recommended make such as Mather and Platt/ KSB/Becon weir/Kirloskar/BE/Jyoti or any other make approved from JSV Department as per BIS 1520-1980 with upto date ammendments read with BIS 9137-1978 or latest edition to suitable for lifting clear water for under mentioned characteristics with bronze impellers/ priming funnels casing ring and shaft sleaves or bronze. shaft of steel grade-with cast iron casing coupled directly through a flexible coupling on a common C.I./Cast steel base plate (base plate to be from the manufacturers of the pumping unit only) to slip ring/squirrel cage screen protected drip proof induction motor existing of standard make such as Kirloskar/Crompton/ Bhel/NGEF/ GEC/ Siemen/ Jyoti/ABB or any other make approved from JSV Deptt.suitable for operation on 410(+) /-10% volts, 50 cycles/ second, 3 phase AC electric supply. The power of electric motor should be atleast 10% in excess of the maximum power required by the pump in the operation range of (+) 10% and (-)15% of the duty point head. The motor /motors cofirming to minimum IE2 norms IS-12615/2011 with up to date amendments.It should include cost of bearing nuts, bolts and pointing etc. and should meet the following requirements:-

Discharge (Q) pump 5.72 LPS for each

Total Dymanic Head 408.65 meter

Rising main Lenght 2700.00 meter

Dia 100 mm

Level at highest discharge point 1449.27 meter

Level pump shaft meter 1076meter

LWL in bore well (H) 1075meter

Pumping hours 16 hours

Suction lift 1 (+ve)

Discharge head 408.57 meter

Residual head 3.00 meter

Static head 337.27 meter

Altitude of installation above MSL 1076 meter

Teperature 20 degree centigrate

Characterstics of water Clear water with turbodity upto 50 PPM Pumps spesifications Make Model Nos of stages Material manufactures certificate to be appended Head Discharge Motor rating (KW) Speed BHP avsorve Effeicency NPSH(K)

ICTP switches with HRC fuses of Kilburn/L&T/Siemens/Standard/Havells make and having Capacity 30% extra of the operational rating as per IS:4064-1978 with upto date ammendments immediately after the power meter of HPSEB. ICTP SWITCHES: I) Type : ii)Make:- iii)Capacity :- Amp.

Providing MS .sheet,16 SWG steel fabricated floor mounted closed(Almirah type) switch board including angle iron post of suitable height and size ISA 40x40x6mm,duly painted, comprising and capable of mounting the following accessories with all internal connections: The drawing of panel board shall be subject to approval of Engineer-in-charge.

OCB/MCCB of MRI/Haveels/Standard make and of suitable capacity of offered motor incoming feeder with or without innitial oil feeling as the case may be with neutral linked under bolltate released as per releveant IS code with upto date ammendments

Earth leakage circuit breaker relay of recommended make such as (Kilburn/L&T/MEI/ GEC) conforming to BIS- 2516-1977 with upto date ammendment and of suitable range which should have control box operating handle and trip/reset bush button on/off indicators, re-indicating off spring condition of the circuit breaker for over current protection. The circuit should be equipped with magnet thermal release with metallic tape etc. It should also be fitted with earth fault for tripping of breaker on occurrence of earth fault on off breaker load side end. ELCB/ELR:- I)Make :- (CEI approved). ii)Type: iii) Range.

Digital power factor meter of standard make AE/L&T/ Havells as per relevants IS code with upto date ammedments

Digital frequency meter of standard make AE/L&T/ Havells as per relevants IS code with upto date ammedments

Bus bar chamber having three copper bars of suitable rating for full length equal to the width of the board for three live phases and one copper bar of half the rating of full length for neutral phase as per BIS:8084-1976 and IS 1353-1985 read with 5578-1985 with upto date ammendments. BUS BAR CHAMBER:- i)Type: - . ii)Make:- iii)Rating

ICTP switches with HRC fuses of Kilburn/L&T/Siemens/Standard/Havells make and having Capacity 30% extra of the operational rating as per IS:4064-1978 with upto date ammendments immediately after the power meter of HPSEB. ICTP SWITCHES: I) Type : ii)Make:- iii)Capacity :- Amp.

Three phase Indicating lamps complete with toggle switches for individual motors as per IS 3452(P-I&II) with upto date ammendments. THREE PHASE INDICATOR:- i) Type:- ii) Make:- iii) Capacity.

Capastor of mechneil/Bhell/GEC make as per 15-2837-1986 with upto date ammendments to rase the power factor at site to 0.954 direct connections to induction motor individually KVA rating accorditng to HP offerd inclduing calbes as per relevant IS code ( OF semins/Clocter/ISE make from bus bar chambet to capacotor also including ICTP switches of appropriate range as per IS 4064-1978 with up to date ammendments

Providng suitalbe oil immersed Starter delta/ direct online / auto transformer/starter roter starter of MEI/Kilbor/Jyoti/L&T/ Seimans make as per IS 8544-1979 with upto date ammendants for squrrel cage/ slip ring motor mounted on pannel board with megnatic type over loade released and dash port time lag under voltage released with or without innitial oil filling as the case may be with single phase preventor as per IS 1248(PV) 1983 withupto date ammendments

Providing Hour run meter of recomended make and suitalbe capacity as per IS 722 (latest edition)

Providing antivibration .pads under the pumps and motors of suitalbe size for the above pumping machinery as per IS 6337-1971

Providing double flanged CI Sluice valve PN 1.0 of Leader/ Bhel/ Kirlosker/ Gld / Kartar Make and equal to dia of scution pipe and capable of with standing the nominal seat pressure IS 780-1984 with upto date ammendments (suitlabe dia)

Providing double flanged cast steel Sluice valve ASA 300 of Leader/ Bhell/ Kirlosker/ Gld / Kartar Make and equal to dia of scution pipe and capable of with standing the nominal seat pressure IS 780-1984 with upto date ammendments (suitlabe dia)

Providing double flanged swing type cast steel reflux valve ASA 300 of Leader/ Bhell/ Kirlosker/ Gld / Kartar Make and having bypas arrangement of 1 step higher then delivery line of pump and capacble with standing normal seat pressure IS 780-1984 with upto date ammendments (suitlabe dia)

Supply of 100 mm circular dia pressure gauge of suitable range of Fiebig/Bourden/ Precision/PREGA with all accessories such as stop cock, copper tubing etc.conformfing to BIS: 3624-1987 or latest with upto date ammendments.

Providing discharge meter of standard make to be fixed on the rising main in pump house as per the directions of the Engineer in charge as per IS:2373:1981 with upto date amendments.

Installation of all the items apparing at serial No. 125 to 146 as per the systematic drawing.

Providing and fixing double flanged MS/GI piping work (Layout to be approved by the Engineer in charge) for suction and delivery pipes suitable to pump(s) offered and common header as per the R/Main respectively complete with all specials such as bends, tees, reducers. Increasers with companions flanges matching with the relevant specifications of the accessories including rubber/asbestos gasket of minimum 3mm thckness as per IS:2712:1979 and required number of nuts and bolts as per Is:1364:1983, The Pipes fittings and joints shall be as per relevant IS code & to withstand 1.5 times total head stipulated under item No.12. The size of the various components to be as under:

Suction pipe : One dia higher then the suction of pump offered and suitable to keep the velocity of flow from 1 to 1.5M/second in the suction pipe

Delivery pipe: One dia higher then the delivery of the pump offered and suitable to keep the velocity of flow from 1.5 to 2M/second in the delivery pipe

Common header:- One dia higher then delivery of pump = 65 mm dia and will extend upto 5 meters from the outer wall of the pump house in the direction to be jointed ( suitalbe dia)

Providing and laying copper PVC insulated armoured power cable (One cable carrying all the three phases) of suitable size and capacity to motors and all other electircal equipments as per IS:1554(P-I) 1988 or latest with upto date amendments of Siemens/GLOSTER /IEC/ICC/EICO/NATIONAL/GRANDLAY make including all other accessories such as thinbles, flexible pipes,solders,nuts and bolts cable glands etc. laid in pipes or trenches under floor.

Motor side (From switch to starter and starter to motor)

Supply side (From Meter of HPSEB to bus bar and switch)

Providing and fixing double loop earth with copper plate 600 mm x 600 x 3 mm thick electrode complete with material such thimbles nuts and charcoal and common salt, 25 mm x 5 mm copper strips as per IS:3043:1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect.(For both phases ).

KUSHAL SINGH RAGHAV

Vineet Sharma

Roop chand

Royal Construction Company