Loading
Loading…
Loading…
Tender ID
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Tender Value
₹1.9 Cr
EMD Value
₹3.7 L
Closing Date
13 Nov 2026, 3:00 pm
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Revenue
TRACK
17 conditions · 5 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Tenderer shall submit the valid competency certificate of welder issued by the manufacturer of electrodes (IRS H3C class) to be used for reconditioning work about their training skill of job
Tenderer shall submit the certificate from the manufacturer of electrodes (IRS H3C class) to be used for reconditioning work for the procurement of genuine material for execution of above job
In absence of certificates specified vide item no. 1 and 2 of special technical criteria, railway will summarily reject their offer.
7 conditions · 1 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tenderer may please note that offers received without requisite/mandatory documents as mentioned above, will be considered as invalid tender and for which contractor shall have no claim on Railway.
The tenderer shall visit the site of work and acquaint himself/themselves with the conditions of work viz. approach roads and accessibility, availability of materials, electric power, water for work and drinking purposes, site for labour camps, stores, godowns, extent of lead/lift in work, availability of skilled and unskilled labour etc. that may be encountered in the course of execution of work. In short, he/they should familiarize himself/themselves fully with the all the conditions of the work site & all the financial implications due to the above conditions is deemed to be understood and taken care of while bidding the offer.
Reconditioning of Switches/Tongue Rails, SEJ's over Delhi Division under DEN/Track/DLI.
NIT-17-26-27-WC~NR
NIT-17-26-27-WC
Open
Works - General
12 Months
Delhi
₹0
₹3.7 L
22 Oct 2026
22 Oct 2026
30 Oct 2026
11 items across 1 schedule · ₹1,87,19,390 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| reconditioning of worn out 1:8½ tongue one tongue rail along with connected of all rail sections under traffic, as in 'IR's Reconditioning of Points & Manual' with RDSO approved and suppliers, finishing & grinding permissible tolerance limit, with all own power T&P, men and materials crossing the track, lead lift and as engineer in-charge. | — | — | — | — | |
| 1 | electrodes | Each | 1000.00 | 1,834.01 | 18,34,010 |
| reconditioning of worn out 1:12 or flatter (only one tongue rail along with stock rail) of all rail sections under prescribed in 'IR's Reconditioning of Crossings Manual' with RDSO approved and suppliers, finishing & grinding permissible tolerance limit, as directed by in-charge : | — | — | — | — | |
| 2 | electrodes | Each | 2000.00 | 2,339.31 | 46,78,620 |
| of worn out 1:8½ tongue rail tongue rail along with connected stock rail sections on Cess or Depot, as in 'IR's Reconditioning of Points & Manual' with RDSO approved and suppliers, finishing & grinding permissible tolerance limit, as directed by in-charge. | — | — | — | — | |
| 3 | electrodes | Each | 500.00 | 1,790.79 | 8,95,395 |
| of worn out 1:12 or flatter tongue one tongue rail along with connected of all rail sections on Cess or Depot, in 'IR's Reconditioning of Points & Manual' with RDSO approved and suppliers, finishing & grinding permissible tolerance limit, as directed by in-charge. | — | — | — | — | |
| 4 | electrodes | Each | 500.00 | 2,030.17 | 10,15,085 |
| of worn out all types of SEJs of to the standard profile by using as per RDSO drawing and in 'IR's Reconditioning of Points & Manual' including grinding to finished etc. complete. Note: Two stock rails + rails will constitute one set of SEJ. | — | — | — | — | |
| 5 | condition | Set | 500.00 | 9,504.64 | 47,52,320 |
| 6 | traffic condition | Set | 500.00 | 11,087.92 | 55,43,960 |
| Schedule total | ₹1,87,19,390 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC-2022withCSupto11.pdf
ATTACHMENT
StandardTenderDocument2022R5withcondition_1.pdf
ATTACHMENT
Specialinstructionstothetenderer.pdf
ATTACHMENT
ManualforRecondioningofMMSteelPointsCrossings.pdf
ATTACHMENT
SpecialConditionTonguerail-SEJ.pdf
ATTACHMENT
RDSO_T_6215_Templates.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .