Certain repairs to Joinery, flooring and misc B/R work including E/M Portion in FAFA, JCOs/OR Md accn (Region 3) and repair and cleaning of sewage line, drain, hard standing at Anarwala under AGE B/R-I of GE Dehradun

Amount

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L brick work with sub class 'B' brick straight or curved on plan exc. 6 m mean radius built in cement mortar 1:6 complete.

All as per Item No. 2.00 here in above but except brick complete. Note : Old serviceable brick obtained from demolition shall be reused. The rate quoted against this item is inclusive of necessary cleaning and stacking of bricks before incorporation in the work.

Taking down cement plastering of any description on brick/stone/concrete wall surfaces of any description incl racking out joints hacking for key,scrubbing down with water etc. complete all as specified and as directed.

M & L 15 mm thick rendering on brick work or concrete surface in cement mortar 1:4, using water proofing compound surface finished even and smooth without using extra cement complete all as specified and as directed. (Note : Rendering will be done in two layer. 1st layer will be 10-12 mm thick and 2nd layer will be 3-5 mm thick. Water proofing compound will be measured and paid separately)

M & L 15 mm thick rendering in cement mortar 1:6 on brick work or concrete surface, finished even and smooth without using extra cement complete all as specified and as directed. (Note : Rendering will be done in two layer. 1st layer will be 10-12 mm thick and 2nd layer will be 3-5 mm thick.)

M & L rendering 15mm thick in patches n exc 3 Sqm in cement mortar 1:4 mixed with water proofing compound on fair faces of brick/concrete surfaces of wall, finished even and smooth without using extra cement complete all as specified and as directed.

M & L rendering 10mm thick in patches n exc 3 Sqm in cement mortar 1:3 mixed with water proofing compound on finished fair faces of concrete surfaces, chajja/ facia finished even and smooth without using extra cement complete all as specified and as directed..

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds, chajjas and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mitres and stopped ends, etc.

M & L 10 mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling, surface finished even and smooth complete all as specified and as directed.

M & L preparing new plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.

M & L preparing new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of wall and applying interior grade wall care putty 2 to 3mm thick to make the surface smooth as specified and directed by Engr-in-Charge. Make : Berger/Asian/JK/Birla

M&L for preparation of wall and applying exterior grade wall care putty 2 to 3mm thick to make the surface smooth as specified and directed by Engr-in-Charge. Make : Berger/Asian/JK/Birla

M&L for preparation of old decorated surfaces of walls (plastered) by brooming down with coir wire brushing, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and finally clean with sand paper all as directed by Engr-in-Charge.

M&L for complete removal of existing treatment from wall upto plaster surface by electric grinder, washing, rubbing down and stopping of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces finally rubbed and smooth with sand paper all as directed by Engr-in-charge.

M&L preparation of old decorated surfaces of ceiling (Plastered) by brooming down or sand paper, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots complete all as specified and as directed.

M&L one coat of white wash on already prepared surfaces of ceiling complete all as specified and directed by Egnr-in-Charge.

M&L one coat of white wash on already prepared surfaces of walls complete all as specified and directed by Egnr-in-Charge.

M&L one coat of oil bound distemper on already prepared surfaces of walls complete all as specified and directed by Engr-in-Charge

M&L one coat of cement base paint on already prepared surfaces of walls on external wall surfaces complete all as specified and directed by Egnr-in-Charge.

M&L two coats oil bound distemper over a coat of primer on undecorated plastered / putty / POP surfaces on walls complete all as specified and directed by Engr-in-Charge.

M&L two coats of cement base paint over a coat of primer on undecorated plastered / putty / POP surfaces on walls complete all as specified and directed by Engr-in-Charge.

M & L preparation of old painted surfaces of wood & wood based material of any description over 10 cm width or girth and applying one coat of PU Paint completeall as specified and as directed.

M & L preparation of old steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as speciied and directed.

Cutting around the pipe 75/100mm bore waste pipe/soil pipe including taking out plant roots up to any depth in brick masonary and rejointing in pipe joint in epoxy mortar (Asian/Berger) and making good to existing surface all as directed by Engr-in-charge. (After the jointing pipe one week to be open for checking of leaking including scaffolding)

Removing / cutting trees vegetation, digging out roots from concrete or brick wall, filling holes on building (Block of 4 qtrs) wall / roof / chajja etc applying and making good with epoxy mortar (Asian/Berger) and applying surface treatment to match with existing specifications complete.

M&L non skid / mat finish ceramic colour tiles of size 300 mm x 300 mm and 6- 7 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 and dismantling of existing floor tiling including cement mortar bedding (but not backing) and rubbish off the premises complete.

M&L non-skid / mat finish designed coloured joint free ceramic tiles of size not less than 400 mm x 400 mm x6- 7 mm thick in floor, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed in cement mortar 1:4 and dismantling of existing tiling including cement mortar bedding (but not backing) and rubbish off the premisescomplete.

All as per item No 29.00 here in above but as in skirting including 10 mm thick rendering in cement mortar 1:4, complete.

M&L glazed ceramic colour tiles size 375 mm x 250 mm x 6-7 mm thick or 450mm X 350mmX 7mm on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering in cement mortar 1:4 and dismantling of existing wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete.

M & L PCC 1:2:4 type B-0 using 12.50 mm graded stone aggregate 25 mm thick as in leveling course to floors complete.

M & L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in benching to drain, holdfast, padding to roof/chhajja, coping, bed block etc. and the like edge slightly rounded or chamfered including necessary use and waste of form work and demolition of existing old cement concrete (un-reinforced) not exc 15 cm thick in ground floor and paving below or above ground level complete.

M&L 75mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection or similar work/places, laid in alternate bays and filling the joints with & including bitumen and sand 1:3 by weight, surface finished even and fair without using extra cement and demolition of existing old cement concrete of plinth protection in ground floor and paving below or above ground level complete.

M & L PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling, mass concrete, sub base or leveling course of floor etc. including demolition of existing old cement concrete (un-reinforced) not exc 15 cm thick in ground floor and paving below or above ground level complete.

M&L 18 to 20 mm thick machine cut polished granite 1st quality "black" stone slab over kitchen platform and similar places over and including 15mm thick screed bed in cement mortar 1:6 laid and jointed with grey cement slurry mixed with pigment to match with existing surface including grinding and moulding of exposed edges of granite including demolition of existing stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and as directed.

M & L for coloured prepolished rubber moulded chequred cement concrete tile 30 cm x 30 cm x 20 to 22 mm thick with 3 mm PVC spacer bar, set, jointed and pointed in neat cement slurry as in floor with grey cement and filling joints with colour pigment over and including 20 mm thick screed bed in cement mortar 1:6 including dismantling of old tiles complete. Make : NTC

Taking down and re-fixing the existing shutter in same opening after & including necessary easing/repair etc. exc. 1 Sqm but n. exc. 2 Sqm each complete.

Taking down shutter of any description exc. 1 Sqm but n. exc. 2 Sqm each complete.

Taking down chowkhats or frames n. exc 1.5 sqm each without taking off shutter from the frame complete.

Taking down chowkhats or frames exc. 1.5 Sqm but not exceeding 4 Sqm each without taking off shutter from the frame complete.

S & F 35mm thick second class hardwood glazed and Skelton factory made door shutters, open rebated and prepared to receive glass/gauze etc divided into squares with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plain, chamfered, fitting with cut and rebated beads for securing glass/ gauge complete all as specified in SSR Pt I-2009 section 8 clause 8.24 (a) and as directed.

S&F factory made 100 % solid wood plastic composite (WPC) door frame 90 x 63 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof, termite proof, fire retardant and having good screw holding capacity all as per specification and drawing as directed by Engineer-in-Charge Make : ECHON/Kumar Tech/Sintex

S&F 30 mm thick moulded WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side palin with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire etardant and having screw holding capacity complete all as specified. Make : ECHON/Kumar Tech/Sintex

S&F factory made 100% solid wood plastic composite (FRP) door frame of size 75 mm x 50 mm x 50 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof termite proof fire retardant and having good screw holding capacity all as specification and drawing complete all as specified and directed by Engr-in-Charge. Make : ECHON/Kumar Tech/Sintex

S&F 24 mm thick moulded FRP factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side palin with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire retardent and having screw holding capacity by Engr-in-Charge. Make : ECHON/Kumar Tech/Sintex

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete.

M&L Rolled sections as in framing or cladding, glazing, door chowkat and the like fixed with angle cleats and connecting plates, etc and including dismantling old section either hooks and hinges or steel hanging door complete

S & F factory made steel window with side hung shutters including projecting/box/pin type hinges with steel handle, steel peg stay,tower bolt etc. complete with glazing bars, dovetailed or welded including dismantling old steel window complete.

S & F factory made steel window with side hung shutters including projecting/box/pin type hinges with steel handle, steel peg stay, tower bolt etc.complete without glazing bars, dovetailed or welded including dismantling old steel window complete .

Taking down existing projected type hings from the steel window carefully with disturbing frame and fix 50 mm long mild steel box type hinge weld to steel frame and shutter with welding and making good including touch with paint and with existing surfaces including scaffolding all as directed by Engr-in-charge.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S&F in repair Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including wooden beading complete all as specified and as directed.

S&F in repair 4 mm thick sheet glass ordinary quality and glazing with silicon and oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane upto triple story of Bldg complete.

Taking out loose sheet glass of any description from windows cleaning the surface thoroughly and refixing the glass with silicon and oil putty or wooden beads as per site requirement upto triple story of Bldg complete.

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 including necessary welding, drilling hole complete.

S&F 18 mm thick PVC ply of one side prelaminated and other side plain white colour for cubboard shutter and frame complete as per specifications and as directed by the engineer - in - charge.Make:-Rajshree, Polyline, ECHON/Kumar Tech

S&F 18 mm thick PVC ply white board to make shelves and partitions for cup boards complete as per specifications and as directed by the Engineer-in- charge. Make:-Rajshree, Polyline, ECHON/Kumar Tech

S&F Continious (PIANO) hinges, mild steel, bright finish or electrogalvanised. 30 mm width of flaps (when open) complete all as specified as directed.

Hasp and staple 100mm safety type, stainless steel 202 grade with hinge pin including bolt to hinge plate and fixed with screws.

S&F 100 mm size stainless steel butt hinges and fixed with stainless steel screws, complete all as specified and directed by Engr-in-Charge.

S&F 200 mm long, solid in one piece stainless steel 202 grade bright finish barrel tower bolts 10mm dia shoot complete all as specified and directed by Engr-in-charge.

S&F 150 mm long, solid in one piece stainless steel 202 grade bright finish barrel tower bolts 10mm dia shoot complete all as specified and directed by Engr-in-charge.

S&F 150mm size solid in one piece stainless steel 202 grade bright finish handles, D type and fixed with stainless steel screws complete all as specified and directed by Engr-in-Charge.

S&F 125mm size solid in one piece stainless steel 202 grade bright finish handles, D type and fixed with stainless steel screws complete all as specified and directed by Engr-in-Charge.

S&F magnet catcher for cub board with brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F stainless steel sliding door bolts 204 grade, hasp and staple type with bright bolt not less than 16mm dia with and incl a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed 250mm long

S&F floor door stopper of stainless steel 202 grade bright finish double legged and tongue, with hard drawn steel spring, fixed in floor, overall length of cover plate 50mm.

S & F in repair 300 mm mild steel, ordinary rat tail rod pattern spring welded to steel/fixed to wooden door frame including roller and roller plate complete.

S&F in repair 1mm wall thickness stainless steel 202 Gde drapery rod with incl brackets, decorative finals at both ends & curtain rings 8 Nos (Minimum) complete. (Note : Sample/ design approved by Engineer-in-charge)

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 15 mm bore GI tubing.

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 20 mm bore GI tubing.

M&L cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting not exc 10cm girth.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing.

Supply and fixing PVC connection 15 mm dia 450 tm long with bras fly nut at both ends complete.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including cantilever brackets of suitable angle iron,CP brass waste coupling ,superior quality PVC waste pipe and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete.

S&F in repair viterous china squatting pan (orissa pattern) long pan size 580x440mm white with integral footrest jointed with trap with epoxy mortar (Asian/Berger), set in cement concrete type B-1 (1:2:4) complete (excluding Trap, flushing cistern and flush pipe) complete all as specified and directed by Engr-in-charge

S&F in repair spun cast iron 600 mm long 'P' trap fixed with epoxy mortar (Asian/Berger), set in cement concrete type B-1 (1:2:4) complete complete all as specified and directed by Engr-in-charge

S & F in repair 10 litre capacity PVC low level cistern ‘ white’ with inlet, float valve including bracket with 32 mm dia PVC pipe/bend 600 mm long complete. Hindware/Parryware/Jaquar.

S&F in repairs 550x400mm wash basin, vitreous china (Flat back) including fixing and pinning in ends of brackets including pop up CP brass waste coupling or requisite size and PVC waste pipe. Make : Cera/Jaquare/Parryware

S & F in repair 75 mm bore UPVC (SWR) pipe 4 kgf/cm2 single socketed in any length with rubber ring, fixed on wall complete all as specified. Make : Supreme/Finolex

S & F in repair 110 mm bore UPVC (SWR) pipe 4 kgf/cm2 single socketed in any length with rubber ring, fixed on wall complete all as specified. Make : Supreme/Finolex

S & F in repair 75 mm bore UPVC (SWR) pipe 4 kgf/cm2 single socketed in any length with rubber ring,joints laid in trenches complete. Make : Supreme/Finolex

S & F in repair 110 mm bore UPVC (SWR) pipe 4 kgf/cm2 single socketed in any length with rubber ring,joints laid in trenches complete. Make : Supreme/Finolex

S & F in repair UPVC (SWR) bend, 75 mm bore' complete all as specified. : Supreme/Finolex

S & F in repair UPVC (SWR) junction single, (Single T) equal or unequalnd, 75 mm bore with access door complete all as specified. : Supreme/Finolex

S & F in repair UPVC (SWR) bend, 110 mm bore' complete all as specified. : Supreme/Finolex

S & F in repair UPVC (SWR) junction single, (Single T) equal or unequalnd, 110 mm bore with access door complete all as specified. : Supreme/Finolex

S & F in repair UPVC (SWR) cowl, 75 mm bore' complete all as specified. : Supreme/Finolex

S & F in repair UPVC (SWR) cowl, 110 mm bore' complete all as specified. : Supreme/Finolex

S&F in repairs PVC tank lid/cover threaded with frame fixed with the existing water storage tank (cylindrical) for 500/1000 ltrs capacity tanks, complete all as specified and directed by Engr-in-charge

S&F in repair pillar taps, brass, chromium plated, with capston heads, fancy type screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make : JAQUAR/Cat part No. KUP-35001PM/Hindware Cat Part No:F370001/Parryware Cat Pat No.T4302A2

S&F in repair brass chromium plated ovehead shower with shower arm complete all as specified and directed. Make : - Parryware Cat Part No T9985A1(Shower) & T-9999A1(Arm)/Hindware Cat Part No F160054 (Shower) & F190016(Arm)/Jaquar Cat Part No OHS 1999 (Shower) & SHA479L300 (Arm).

S & F in repair 15 mm dia bore brass chromium plated concealed stop cock, complete. Make :Jaquar/Hindware/Parryware

S&F in repair 15 mm bore Angle stop valves, cast copper alloy, fancy type chromium plated screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed. Make : - JAQUAR Cat Part No FON-40053/Hindware Cat Part No F160017/Parryware

S&F in repair 15mm bore Bib taps short body, cast copper alloy fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make : - JAQUAR CAT Part No ALI-85037/Hindweare CAT Part No F-370004/Parryware

S&F plate rack 200mm and size 90 x 75 cm made out off 1.00 mm thick stainless steel grade 304 complete all as specified and as directed.

S & F in repair PTMTgrating square 150 mm size complete all as specified. Make : Prayag Cat No. 115

S&F in repairs brass chromium plated towel rail, 20mm dia 'D' type 60cm long between flanges. Make : Jaquar/Hindware/Parryware

Cleaning of existing PVC/RCC water storage tank with vaccum cleaner machine exc 250 to 500 ltrs capacity with D scaler (Taski) and dry with and apply on coat of anti bacterial spray (R1 Taski) as directed by Engr-in-charge. Date of cleaning to and CA No to be painted on water storage tank with stencil in black/ white synthetic enamel paint all as directed by Engr-in-Charge.

S & F rotational moulded polyethylene water storage tanks 500 Ltr triple layer white, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-2009 including dismantling of existing unserviceable tank and removing from site, complete.

S & F rotational moulded polyethylene water storage tanks 1000 ltr triple layer white, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-2009 including dismantling of existing unserviceable tank and removing from site, complete.

S&F in repairs 75mm dia centrifugally cast (spun) iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B 1(1:2:4)

S & F in repairs 20 mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete.

S & F in repairs ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (Minimum weight 210 gms) complete.

M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for 60 mm thick pre polished rubber moulded coloured machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658- 2006 M-35 Grade with grey cement and no pigment complete all as specified and as directed by the Engr-in-Charge.

M&L for machine cut kota stone slab flooring 20-25mm thick over 20mm thick cement screed in cement mortar 1:6 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete.

Providing & fixing false ceiling of Designer tile Ivory painted (High Pressure Steam cured) of 4mm thickness (as per IS : 14862) of size 595x595mm and any one of the design (Cascade or electra) in true horizental level, suspended on inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and croos 'T' of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main "T" at 600 mm c/c to form a grid of

All as per item No 111.00 (Contd/---) …. 1200x600mm and secondary cross "T" of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable wire of 4mm dia with galvanised butterfly level clips, spaced at 1200mm c/c along main 'T', bottom exposed width of 15mm of all 'T'' sections of 4mm dia GI wire shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width, including taking down existing ceiling all complete at all heights as per direction of Engineer-in-Charge.

S&F in repairs powder coated aluminium door with frame and shutter with glazing, following accessories and glazing with 4.8 mm thick retro reflected glass, rubber gasket, aluminium glazing clips, aluminium beading, mortice lock, aluminium stopper cleat, iron mongary, fabricated with following aluminium section:- Frame: 100x44x1.20 mm thick with rawl plug ,Middle lock rail: 85x44x1.20 mm thick, Bottom rail : 150x44x1.20mm thick, Top rail & Style : 85x44x1.20 mm thick, Aluminium glazing beading 0.70 mm thick, Aluminium handle 'D' type : 150 mm, Aluminium tower bolt 9.9 mm dia shoot 200 mm long, Mortice lock Brass: 100 mm 4 lever, Aluminium stopper cleat, Stainless steel hinges 100 mm long. Note: making good of wall surface with matching to existing surface complete all as specified and directed.

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F in repair Aluminium (Die Cast body) Door closer hydraulically regulated designation No 1 universal type suitable for door shutters up to 851 mm to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified & directed.

S&F in repair Brass Mortice lock, two levers vertical type, size 100 mm size

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of old sheet complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding/ridge to wall, fixed with self tapping screws as specified

S & F mild steel work as in main and cross beam, hip and jack rafters, purlins etc. fixed with angle cleat or other connecting plate complete confirming to Fe – 410-O or Fe – 310-O including dismantling old section complete all as specified and as directed.

M & L applying two coats of synthetic enamel paint on new or previously untreated steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete.

M&L for 100mm thick pcc flooring in Cement concrete type B-1, 1:2:4 (20mm graded aggregate) finished surface even and smooth without using extra cement complete all as specified.

Taking out existing roof treatment and M&L for water proofing treatment on roof slab including picking, sweeping clean and washing down with water to remove dust & providing water proofing treatment described as under:- (a) Surface preparation with Asian smart care mortar and GP groute mortar and treating of construction joints, filling of honey combs with polymer modified mortar (Cement: Sand : smart care multipurpose polymer of Asian Paints or equivalent product of Thermax/ Berger ) (b) Cleaning the surface and applying (Resin & Hardner) smart care Epoxy Primer 2k of Make Asian paints or equivalent product of Thermax/ Berger ) on the cleaned surface for bonding of PU magnum with the existing concrete surface.

All as per item No 123.00 (Contd/--)… (c) Supplying, providing and applying waterproofing treatment to Terrace area with Asian Paints Smart care PU magnum, single component highly elastomeric seamless cold applied modified PU coating or equivalent product of Thermax/ Berger) including all necessary surface preparation, coving using smart care multipurpose polymer, water pond test, etc. complete as per manufacture's specifications and application methodology. The same coating shall be applied in two coats achieving a total thickness of 1mm. The coating shall have dual combination of 250% elongation . Execution to be done with authorised applicator of the manufacturer and company back gurantee to be given by the contractor. Work will be executed in smart assurance system

Cleaning of manholes not exceeding 1.5m depth and removing the sludge and burying the waste material in borrow pits. Note:-(cost of the borrowpit shall be deemed to be included in the quoted rates of this item).

M&L for dewatering and desludging of septic septic tank/sokage well of any size and depth by manually/mechanically (solid contents if not removed by mechanically should be removed by manually) and removing the sludge out side of MOD complete all as directed at site. After complete cleaning of septic tank the manhole cover shall be re-fixed in same position with CM 1:4 and bleaching powder spread on top surface of septic tank @ 1 Kg per septic tank complete all as specified and directed at site.

Pumping out sewage water from the man holes /Septic taank/soakage well at different locations by means of sewage tanker fitted with pump (5000 Ltr capacity) and disposing out off MD land as directed by Engineer-in-charge.

Excavation in trench in any type of soil not exceeding 1.5M wide and not exceeding 1.5M in depth for sewage line, manhole etc not exceeding 10 sqm on plan and getting out in any type of soil complete.

Demolition and breaking drain pipe 1500mm (salt glazed stoneware) set in cement mortar complete all as specified.

Supplying, laying, jointing and testing salt glazed stone ware drain pipe 1500mm internal dia of length 75 cm grade ‘A’ confirming to IS–651–1980 laid in trenches and jointed in cement mortar 1:1 including cement concrete bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate complete for the following dia :-

Returning, filling in, including spreading, watering and well ramming in layers n. exc 25 cm thick in any type of soil complete.

Removing excavated material to a distance n exc 50M and deposited where directed at a level n. exc 1.5M above the starting point complete.

M&L for 60 mm thick vibromatic reinforced precast cement concrete 1:1:2 (using 20mm graded stone aggregate) with 2mm thick mild steel CR sheet around painted with 2 coats of bituminous paint , as in man hole cover slabs finish fair even and smooth without using extra cement ( Top surface will be chequred finish) including necessary form work, 100 mm long handle of 12mm dia round bar counter sunk by 25mm welded to reinforcement complete all as specified and directed by Engr-in-charge (Note : CA No and date will be engraved on covers. Reinforcement shall be measured and paid separately. Curing will carried out with ponding method)

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips (TMT)

M&L for TMT bars 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

M/L walling of random rubble ,uncoursed well bonded built in CM (1:6) as in parapet,steps complete all as specified & directed by Engineer-in -Charge.

All as per item No 135.00 here in above but except stone

M&L for raised pointing to RR stone walling with CM 1:3 complete all as specified and as directed.

M & L 15 mm thick rendering on brick work or concrete surface of manhole, septic tank in cement mortar 1:4 surface finished even and smooth complete.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, lamp holders, regulators, sockets, light fitting any type etc complete. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed by Engr-in-charge

M&L for Point wiring with1100 Volts, grade 1.5 Sqmm. (nominal area), PVC insulated but unsheathed multistranded copper conductor single core FRLS cable drawn through and including non metallic medium duty rigid PVC concealed conduit (medium duty) 20mm dia or higher size complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc including pressed steel juction box of thickness1.2mm for mounting of switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable green colour as earth wire upto common earth and connected to earth dolly complete all as specified and directed by Engr-in-charge for the following.

(a) One light / exhaust fan point controlled by one-one way switch.

(b) One ceiling fan point controlled by one-one way switch through regulator.

(c) One bell Point controlled by bell push switch

(d) One three pin 5 Amp socket on same board with other switches.

(e) One three pin 5 Amp socket on independent board.

(f) One light point controlled by two -2 way switches

All as per item No.141.00 here in above but with 2.5 Sqmm. (nominal area) wire/cable for phase and neutral for one 3 Pin 15 amp socket on independent board including one 2.5 sqmm PVC insulated unsheathed multi stranded copper conductor cable, FRLS 1100 volts grade as earth continuity conductor upto common earth & connected to earth dolly complete all as specified and directed by Eng.-in-charge.

M&L for point wiring with1100 Volts, grade 1.5 Sqmm. (nominal area) ,PVC insulated but unsheathed multistranded copper conductor single core FRLS cable drawn through existing steel/PVC conduit etc and existing terminal boxes but with new 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable green colour as earth wire upto common earth and connected to earth dolly complete all as specified and directed by Engr.-in-charge of following.

(a) One light / exhaust fan point controlled by one-one way switch.

(b) One ceiling fan point controlled by one-one way switch through regulator.

(d) One three pin 5 Amp socket on same board with other switches.

(e) One three pin 5 Amp socket on independent board.

(c) One bell point controlled by bell push switch

(f) One light point controlled by two -2 way switches

All as per Item No 142.00 here in above but one three pin 15 Amps switch socket out let on the independent board with 2.5 sq mm PVC insulated FRLS copper conductor and 2.5 Sqmm FRLS copper conductor for continuous earthing complete.

S&F switch piano one way flush type 5 Amp SP 250 Volt AC complete all as specified & directed.

S&F switch piano two way flush type 5 Amp SP 250 Volt AC complete all as specified & directed.

S&F switch piano one way flush type 15 Amp SP 250 Volt AC complete all as specified & directed.

S&F socket outlet multipurpose 3 Pin 5 Amp and 2 Pin 5 Amps 250 V AC complete all as specified & directed.

S&F socket outlet 2-in1,3 pin 5 and 15 Amp flush type 250V AC complete all as specified & directed.

S&F Bell push flush, flush type 5 Amp SP 250 Volt AC complete all as specified & directed.

S&F Bell Ding dong 250V AC complete all as specified & directed.

S&F ceiling rose surface bakelite 3 terminals of size 65x25mm. complete .

S&F step type, electronic fan regulator 120 watts, 5 step for ceiling fan 1200/1400 mm sweep 230 volts AC.

S&F lamp holder PVC/polycarbonate type with LED lamp 7 watt retrofit complete all as specified & directed.

S&F lamp holder PVC/polycarbonate type with LED lamp 10/14 watt retrofit complete all as specified & directed.

S&F lamp holder PVC/polycarbonate type with LED lamp 3/5 watt retrofit complete all as specified & directed.

S&F in repairs switch piano one way flush type 5 Amp SP 250 Volt AC complete all as specified & directed.

S&F in repairs switch piano two way flush type 5 Amp SP 250 Volt AC complete all as specified & directed.

S&F in repairs switch piano one way flush type 15 Amp SP 250 Volt AC complete all as specified & directed.

S&F in repairs socket outlet multipurpose 3 Pin 5 Amp and 2 Pin 5 Amps 250 V AC complete all as specified & directed.

S&F in repairs socket outlet 2 in1,3 pin 5 and 15 Amp flush type 250V AC complete all as specified & directed.

S&F in repairs Bell push flush, flush type 5 Amp SP 250 Volt AC complete all as specified & directed.

S&F in repairs Bell Ding dong 250V AC complete all as specified & directed.

S&F in repairs ceiling rose surface bakelite 3 terminals of size 65x25mm. complete .

S&F in repairs step type, electronic fan regulator 120 watts, 5 step for ceiling fan 1200/1400 mm sweep 230 volts AC.

S&F in repairs lamp holder PVC/polycarbonate body complete all as specified & directed.

S&F in replacement mirror light decorative compact luminarious with decorative ends caps 9/10 Watt LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size . Make Havells Cat No E-Lite Pride LHEXBLP7IN1W009 or eqvt in Philips/Wipro

S&F in replacement wall mounted tube light fitting 1x20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 4000K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed. Make:Wipro Cat part No LL20-281-XXX-65AL1/ Philips cat part No BN021C LED20S PSU CWGR S2/Havells Cat No ENDURA LINEARNEOBS20W LED840SPCWH.

Supply and fixing in replacement LED tube rod 18/20 Watts single or double sided connections polycarbonate complete incl making connection alteration in existing tube light fitting complete all as specified and directed. Make: Philips / Bajaj/ Havells.

S&F in replacement energy saving Bulk head luminaire with opal diffuser with and including retrofit LED lamp 10 watts complete all as specified and directed by Engr-in-charge. Make : CG part No LBHP-10-CDL/ Philips WT 140W LED 7S CW PSU S1PC/ /Havells ENDURA RUGBYNEO N / MEPRO BCL 23 PLAIN

S&F in replacement Busbar chamber of size 600x315x214 mm or higher size with PVC hinged lid suitable for and mounting arrangement for fixing of MCCB 4 pole, duly connected with and incl 04 Nos of copper Busbar 300 Amps fixed on epoxy insulators, Gun metal cable gland of 25 Sqmm 01 No and PVC coupler for sub main wires 04 Nos complete Polycarbonate type (shock proof, rust free, corrosion free, acid and chemical resistant, fire retardant, having high impact, made of halogen and silica free recyclable material), UV resistant, having high grade gasket made of Polyurethane, flame retardant,complete all as directed at site by Engr in charge or his rep complete. Note:- Only MCCB shall be measured and paid for seperately all other items incl connection of MCCB to busbar incl thimble, bottle lugs etc and fixing arrangement ie clamp, bracket etc as directed by Engr in charge are included in item rate. Make:- Hensel/ABB/BCH/Schneider/Cape

S&F in repairs TPN DB VTPN 4 way 415 Volts, 50 Hz indoor type double door sheet metal enclosure IP-43 protection flush mounted with copper busbar for each phase with two neutral bar & two earthbar and cable ties for cable managenment including mounting arrangement for 100/125 Amps four pole 415 volts MCCB as incomer and MCBs as outgoing complete pre wired with suitable size copper conductor incl taking out unserviceable DBs, MCCB and MCBs of any capacity complete all as specified and directed by Engr-in-charge. The DB's should hold type test certificate (CPRI) as per IEC 61439-3 Make: Legrand/L&T/ Indo Asian/C&S.

S&F in repairs distribution board SPN 8 way 240 volt with suitable rated bus bar double door IP-43 DB's mounting flush on wall/concealed and making good distubed surfaces incl taking out unserviceable DB any capacity complete all as specified and directed by Engr-in-charge. Make: Legrand/ L&T/ Indo Asian..

S&F in repairs distribution board SPN 4 way 240 volt with suitable rated bus bar double door IP-43 DB's mounting flush on wall/concealed and making good distubed surfaces incl taking out unserviceable DB any capacity complete all as specified and directed by Engr-in-charge. Make: Legrand/ L&T/ Indo Asian..

S&F in repairs distribution board SPN 2 way 240 volt with suitable rated bus bar single door IP-43 DB's mounting flush on wall/concealed and making good distubed surfaces incl taking out unserviceable DB any capacity complete all as specified and directed by Engr-in-charge. Make: Legrand/ L&T/ Indo Asian..

S&F in replacement Sheet metal enclosure SPN with a two pin and earth plug and socket complete with one 20 amp single pole 10 KA C series MCB complete all as specrified & directed

S&F in replacement of MCCB 100 Amps four pole 415 volts thermal magnetic release ICU=100% ICS having breaking capacity 16 KA including connection terminal strip complete all as specified & directed Make:Legrand/ L&T/ Indo Asian/C&S

S&F MCB single pole 240 volt, 10 KA, 6 to 32 Amp, 'B' series confirming to IS complete all as specified and directed. Make: Legrand/L&T/Indo Asian/C&S.

S&F MCB SPN 240 Volt 10 KA 6 to 32 Amp 'B' series conforming to IS complete all as specified & directed. Make: Legrand/L&T/Indo Asian..

S&F MCB SP 240 Volt 10 KA 40 Amp 'B' series conforming to IS complete all as specified & directed. Make: Legrand/L&T/Indo Asian..

M&L for replacement of Unserviceable Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level, earth plate surrounded by and packed with a 15 cm thick layer of char coal dust and common salt, earth lead GI wire 4.00 mm. dia by means of bolts, Nuts, Check Nuts and washers of galvanized iron and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe medium 15 mm. bore,

All as per item No 180.00 (Contd/--) .. and water pipe 20 mm. bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 & 75 mm thick RCC (1:2:4) type B1 cover slab reinforced with 8mm TMT bars 100mm c/c both ways complete all as specified & shown in elect plate No. 3 of SSR part I of 2009 and testing on completion. Note: (i) If the desired earth resistance is not found within permissible limit shall be redone by contractor at no extra cost. (ii) Cost of GI wire 4 sqmm and 15 mm dia pipe medium grade upto 7.5 mtr is included in the rate quoted for this item

M&L for sub main wiring with 2 Single core PVC insulated unsheathed cable 1100 Volts grade heavy duty copper conductor multistranded of size 4 Sqmm (nominal area) drawing in and including 20 mm dia or higher medium duty PVC concealed conduit and conduit accessories and fittings. Including one single core green colour PVC Insulated unsheathed cable copper conductor multistranded of size 4 Sq mm as earth wire upto common earth and connected to earth dolly complete incl taking out old unserviceable submain all as specified & directed.

All as per item No 181.00 here in above but drawing through existing concealed conduit incl taking out old unserviceable submain all as specified & directed.

S&F in repairs laminated sheet 3mm thick of size 125x100mm including cutting slots for fixing switches etc all as directed

S&F in repairs laminated sheet 3mm thick of size 200x125mm including cutting slots for fixing switches etc all as directed

S&F in repairs laminated sheet 3mm thick of size 200x250mm including cutting slots for fixing switches etc all as directed

S&F in repairs laminated sheet 3mm thick of size 100x100mm including cutting slots for fixing switches etc all as directed

S&F in repairs pressed steel terminal sunken box 1.2mm thick of size 125x100mm for mounting of sheet cover incl cutting chases, plastering, making good disturbed surfaces of wall, painting as per existing to match the wall complete all as directed.

S&F in repairs pressed steel terminal sunken box 1.2mm thick of size 200x125mm for mounting of sheet cover incl cutting chases, plastering, making good disturbed surfaces of wall, painting as per existing to match the wall complete all as directed.

S&F in repairs pressed steel terminal sunken box 1.2mm thick of size 200x250mm for mounting of sheet cover incl cutting chases, plastering, making good disturbed surfaces of wall, painting as per existing to match the wall complete all as directed.

S&F in repairs pressed steel terminal sunken box 1.2mm thick of size 100x100mm for mounting of sheet cover incl cutting chases, plastering, making good disturbed surfaces of wall, painting as per existing to match the wall complete all as directed.

Supply and laying in repairs XLPE insulated, armoured, heavy duty electric cable, with multi stranded aluminum conductor served with an inner sheathing of PVC type armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area 25 Sqmm 3.5 core incl lugs thimbles bottle timbles and gun metal cable glands and heat shrinkable PVC sleeves on exposed surfaces and teflon tape duly insulated complete laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including taking out existing cable complete all as specified and directed by the Engr-in-Charge. Make : Havells/Polycab/KEI/Grandlay

All as per item No 191.00 here in above but cross sectional area 10 Sqmm 2 core incl taking out old unserviceable submain all as specified & directed.

M&L for sand cushioning in trenches for protection of UG cable with river bed sand laid dry in trenches before and after laying of cable, including well ramming and consolidation complete all as specified and directed.

M&L for providing of new sub class 'B' bricks, old size, well burnt laid flat dry for protection of under ground cable complete all as specified and directed.

Supply and laying in replacement of GI Steel tubing medium grade 40 mm dia including all fitting laying in trenches or grouting/fixing in wall for protection of cable complete all as specified and directed by Engineer-in-charge

S&F in replacement tamper proof electronic single phase whole currrent energy meter (LCD display) 10 Amp to 60 Amp, 240 volt class 1.00 and AC supply including cable connection, proper sealing with barcode with PVC seal. The meter shall comply with the latest version of IS-13779 with at least 2 anti tamper LED indications of line load reversal and earth loading indication including electrical connection with existing system and sealing properly including push fit type transparent meter box . The meter shall work satisfactory with guaranteed accuracy as per limit of IS: 13779. The meter shall be fixed on existing steel boxes on wall complete all as specified and directed. Make:- Secure /L&T/BHEL (Note:- Old unserviceable meter will be deposited to E/M store yard)

S&F in replacement Meter Distribution Board made out of Thermoplastic polycarbonate of size 600x600x170 mm (dust proof & weather proof ,shock proof, rust proof ,corrosion free , acid & chemical resistance ,UV resistance , halogen free & recyclable material) wiyh 230v Ac 50 HZ 3 Wire, suitable for mounting of electronic Meter -04 Nos incuding electrical connection with exsisting system and sealing properly & taking out u/s broken/rusted box of any size and type complete all as specified and directed. Make Hensel cat part no Mi0800 / Secure/Sintex

S&F in replacement Bldg Security light fitting comprising of pressure die cast aluminium housing heat resistant toughened glass IP-65, photovoltic LDR sensor with separate surge protection 5KA, 35 Watts or near higher size fixed on and including GI pipe bracket made of 40 mm bore medium grade pipe 1.2m long made to shape, MS clamps of size 32 x 3 mm flat iron, nuts, bolts and washers of required size and painting complete with all necessary electric connection etc all as specified and directed. Make: Greenstar Cat No: DSS3 or equivalent in Philips / Crompton.

Taking down existing electric metre and refixing in new position with all nut bolts screws etc connecting up completely including necessary copper wires of suitable size complete all as directed.

M/S C S AITHANI

M/S JAI PRAKASH GOEL

M/s Pradeep Kumar

M/s Anil Kumar