Construction of new inspection Bungalow at Meshwo resrvoir project waste wier at village Venpur, Taluka : Shamlaji, Dist : Arvalli.

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials

and disposing off the excavated stuff upto 50 Meter lead.(B) Dense or Hard soil

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful

materials and disposing off the excavated stuff upto 50 Meter lead.(B) Dense or Hard soil

Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand : 8- hand broken stone

3 aggregates 40 mm nominal size) and curing complete excluding cost of formwork in (A) Foundation and 21.1 Cum 2769.69

Providing and laying controlled cement concrete M.200 and curing complete including the cost of

4 formwork but excluding the cost of reinforcement for reinforced concrete work in (A) Foundations, 15.3 Cum 4309.67

footings, Base of columns and Mass concrete.

Providing and laying controlled cement concrete M-200 and finishing smooth with cuing etc. complete

5 including the cost of formwork but excluding the cost of reinforcement for reinforced concrete work in 2.2 Cum 7536.62

columns up to Ground level (Pedestal).

Filling available excavated earth (excluding rock) in trenches. sides of foundations etc. in layers not

exceeding 20 cm. in depth consolidating each deposited layer by ramming and watering.

Carring out plinth treatment to post construction / by spraying chemical solution for termite control

treatment including labour and material consistment with I.S.I specification. Using Chlordene and

Chiorpurfiles 20 EC. As Per 6131_paret-II Consentration Weight one percent is recommended,

i.e one litre 20 EC chemical emulsion with 19 liter give 1 % concrentration inclusive of one litre

chemical emulsion appication at the rate of 5 Litre chemical / Sqm of surface is recommended as

Providing and laying controlled cement concrete M-200 and curing complete including the cost of

formwork but excluding the cost of reinforcement for RCC work in Ground beam and Plinth Beam.

consolidating etc. complete.

10 Filling in plinth with sand under floors including watering ramming, consolidating and dressing complete. 14.7 Cum 481.8

Providing and laying controlled cement concrete M.200 and curing complete Including the cost of

11 formwork but excluding reinforcement for reinforced concrete work in Columns, Pillars posts and struts, 3.8 Cum 7889.11

Ground floor level.

Providing and laying controlled cement concrete M.200 and curing complete Including the cost of

12 formwork but excluding reinforcement for reinforced concrete work in Columns, Pillars posts and struts, 3.8 Cum 7930.52

First floor level.

Providing and laying controlled cement concrete M.200 and curing complete including the cost of

formwork but excluding reinforcement for reinforced concrete work in Beams, Ground Floor Level.

Providing and laying controlled cement concrete M.200 and curing complete including the cost of

formwork but excluding reinforcement for reinforced concrete work in Beams, First Floor Level.

Providing and laying Controlled cement concrete M-200 with curing etc. complete, including the cost of

formwork but excluding the cost of reinforcement for R.C.C. slabs work for Ground Floor

Providing and laying Controlled cement concrete M-200 with curing etc. complete, including the cost of

formwork but excluding the cost of reinforcement for R.C.C. slabs work for First Floor

Providing and laying Controlled cement concrete M-200 For R.C.C. lintel/Chhajja with curing etc.

complete, including the cost of Formwork but excluding the cost of reinforcement for Ground Floor.

Providing and laying Controlled cement concrete M-200 For R.C.C. lintel/Chhajja with curing etc.

complete, including the cost of Formwork but excluding the cost of reinforcement for First Floor.

Providing and laying Controlled cement concrete M-200 Curing etc. complete, including the cost of

Formwork but excluding the cost of reinforcement for R.C.C. Stair case for Ground Floor.

Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding and placing in

position complete upto floor two level

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm.

21 in in superstructure above floor two level in Cement mortar 1:5 ( 1-Cement : 5-coarse sand ) 32.7 Cum 4526.75

Conventional (Ground Floor)

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm.

22 in in superstructure above floor two level in Cement mortar 1:5 ( 1-Cement : 5-coarse sand ) 31.4 Cum 4569.18

Conventional (First Floor)

Providing 10mm thick cement plaster in single coat on ceilling for interior plastering upto floor two level

and finished even and smooth in (i)Cement mortar 1:3 (1-cement:3-sand)

Providing 10mm thick cement plaster in single coat on brick/concrete walls for interior plastering upto

floor two level and finished even and smooth in (i)Cement mortar 1:3 (1-cement:3-sand)

20mm thick sand faced gutka finish cement plaster on walls upto height 10 metres above ground level

25 consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of 353.9 Sqmt 321.1

C.M. 1:1 (1-cement : 1-sand) etc. complete.

Applying two coats of Birla or Asian acrylic lappy (putty) and two coats of primer of approved brand

26 and manufacture on new wall surface to give an even shade including thoroughly brushing the 617.9 Sqmt 40.59

surface free from mortar dropping and other foreign matter and sand papered smooth.

Wall painting (three coats) with plastic emulsion paint of approved brand and manufacture on wall

27 surfaces to give an even shade including thoroughly brushing the surface free from mortar dropings 617.9 Sqmt 125.52

and other foreign matter and sand papered smooth

Providing and fixing window having extruded aluminum Colour anodized section frame main outer size

63.50 x 38.10 x 1.95 mm,@ Wt 1.094 Kg / Rmt, horizontal two track member size 61.85 mm x 31.75 mm

x 1.20mm @ wt.of 0.695 Kg/mt, vertical member of size 61.85 mm x 31.75mm x 1.30 mm @ wt.of

28 Kg/mt with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt, 25 Sqmt 1713.7

vertical member of size 40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt, @ Wt. 0.457 Kg/mt with 5 mm

thick transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and

transparent silicon sealant glass fixing to frame as per details etc complete for window.

Providing and fixing standared extruded of alluminium section of size 63mm x 38.10mm x 1.2mm @ Wt.

29 0.643 Kg/mt with colour anodized alluminium frame for ventilation with 5 mm thick frosted glass as details 1.1 Sqmt 1175.56

etc complete for Ventilation

providing and fixing 30 mm thick solid core flush type door having outer frame 5" thick teack wood fram

with all core should be teak wood Patti and both side decorative 4.0MM thick teak veneer finished( with

30 pu polish and fixed with granite framing include 150mm top and bottom s.s. pivot and s.s. screws)and 16.7 Sqmt 4767.2

europa make tubular lock system including as per architect instruction etc( flush door basic rate should

be 160 rs /sq.ft and veneer basic rate 95 rs/sqft). Complete

Providing and fixing FRP frame size 100x50 mm and 28mm thick FRP depress panel shutter having extra

reinforcement on sides & edges in Gel coat finish. The core of the shutter & frame is to be filed up with

injected fire retardant grade polyurethene foam done in situ alongwith embedded wooden pieces for

stiffening & also taking hinges & fintures. The whole FRP frame & shutter is to be water proof weather

proof, termite proof & resistance to mild acid/alkali. Rates are to be inclusive of S.S hinges with

necessary screws & alluminium fixtures & fastenings & fastener sleeve.

Providing fabricating, erecting and fixing of M.S.grill, fabricated from m.s. plat, angles, tees, spacebar,

round bar, pipes etc. complete as per Architect detail & Drawing including applying one coat of red oxide

& two coat synthetic enamel paint etc complete. As per Architect instructions and drawing or as directed

by engineer in charge.

Providing and laying 1200 mm X 600 mm X 8 (Matt & Glossy Finish) to 10mm thick ( or above size) first

quality virified floor tiles of desired finish (fully polished glossy, matt, satin, guard, anti skid) in desired

pattern in floor & wall with residue and skirting as per drawing / specification. The tiles shall have

minimum scratch hardness of 7 on Moh's scale with a density of 2.2 to 2.3 & bonding strength of

kg/sqcm. The tiles shall be set with cement slurry (3.3 kg. cement / m2.) over a minimum 25 mm. thick

cement sand mortar (1:3) bedding on average 40 mm thick (1:2:4- 6mm down aggregates) wired finish

33 screed & laid to proper gradient. Finishing to be done with flush pointing in white cement & matching 252.8 Sqmt 1722.05

approved pigment incl. curing, polishing & cleaning with mild oxalic acid etc. complete for all floors / all

levels, as per drawing / specification and or as per direction of Engineer in charge for flooring, skirting or

channel work etc. complete The rate should be inclusive of protection of flooring until the handling of

project by covering the joints with abrotaps, plastic sheet & plaster of Paris. The rate shall include cost of

25mm cement mortar, 40mm wired finish screed.(basic rate of tiles- 65 rs/sq.ft) ( make johnson,

RAK,karjariya,SYMPOLO or approved make)

Pro. And fixing single layer water proof gypsum board 12.5 mm thick sections using water proof board of

size 1220 mm x 1830 mm x 8.0 mm suspended by GI suspender channel of size 25 mm x 3 mm with

intermediate channel og size 18 mm x 40 mm x 0.8 mm at 1220 mm center to center ceiling section of

34 size 40 mm x 35 mm x 0.55 mm at 457 mm c/c and perimeter channel A of size 20 mm x 27 mm x 30 108.7 Sqmt 606.95

mm x 0.5 mm at edges & drops incl.paper tap sand sofit cleat, anchor fastener, scoch bolt connecting

cleat,joining compound top coat on ceiling incl.making necy.opening for light fitting,diffuser etc. comp. as

per detail drawing as directed

Providing & fixing granite stone average 18 mm thick machine-cut & machined polished stone in treads of

steps, sill, copings, parapet top, window,door,sill, planter top, and such other locations, laid on

mm(average) thick cement mortar 1:4 (1 cement:4coarse sand) and jointed with Super flex guranted

fixing solution by kerakoll mixed with pigment to match the shades of the slabs, including rubbing and

polishing complete. The Stone used should be in one single long piece up to 3000 mm as per drawing or

as directed by Engineer-in-charge. The exposed projected edges shall be of uniform thickness and of

uniform projection including molding , chamfering, rounding, polishing complete. (basic rate of granite-

Providing and laying Vitrified tiles 8 to 10 mm thick , in skrting risers of steps and dedo on 10mm thick

cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National

37 Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps 25 Sqmt 170.36

including making good the wall, ceiling and floor etc. complete.[A] 15 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National

38 Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps 50 Sqmt 253.82

including making good the wall, ceiling and floor etc. complete. [C] 25 mm.

Providing laying and jointing in true line and level 40 mm dia. U.P.V.C. Pipe (SCH -40) line including

fittings apprroved by Engineer In charge. Pipe shall be fixed on the wall with the help of clamp at

every two meter C/C or shall be concealed as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 110 diameter U.P.V.C. SWR Type B pipe confirming to

IS 13592-1992 with one end plain and other end socketed with rubbering, & fitting conforming

to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with

40 each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 70 Rmt 876.11

mm diameter x 149 mm length x 145 mm high at every 2000 mm centre to centre or shall be

concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing

of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing and fixing to wall ceiling floor 10.0 Kg. F/Cm2 working pressure polythene pipes for soil

waste and ventilating pipes of the following outside dia. low density, complete with necessary

fittings ,wall clamps etc including making good the wall ceiling and floor. {Finolex, Supreme,

Prince or equivalent brand} (A) 110 mm

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the following

42 nominal diameter of self cleansing design with C.I scread down or hinged grating including the cost of 5 Nos 586.6

cutting and making good the walls.

Providing and fixing Screw down Quarter turn bib taps of following size (A) Brass chromium plated

screw down Bib tap (I) 15 mm dia

44 Providing and fixing C.P. bib cock 15mm φ heavy duty with cap 5 Nos 602.58

45 Providing and fixing C.P. Pillar cock 15 mm Heavy duty swan neck 4 Nos 849.95

providing and fixing screw down brass chromium plated heavy quality bib-tap of Johnson (Coral brass

46 long nose T1325C) on water supply pipe lines of 15mm dia with or with extension piece but with a flange 3 Nos 2070.5

etc. complete to the satisfaction of EI and approved Johnson/ cera make.

providing and fixing white glazed vitreous chinaware over the counter type / under counter type wash

basin with / without single or double hole for pillar-tap comprising of (a) white glazed vitreous chinaware

wash basin of Johnson ( omega recta NXT ) make with supporting MS or CI brackets. (b)1 no. 32mm CP

cast brass bottle trap Johnson ( T0060C) heavy casted of Johnson /cera make, with 250mm long wall

connection pipe and wall flange with rubber adopter for waste connection and one waste coupling. (c)

no heavy quality CP brass angle cock ( T0410C) with wall CP flange of Johnson make. , (d)1 no 15mm

NB heavy quality CP brass inlet connection with unions end. the supporting bracket shall be painted with

3 coats of approved paint of approved shade etc complete

providing and fixing (A) White glazed vitreous chinaware extended wall mounted cantilever type

European type water closet (Johnson make BREEZE model 520 x 360 x 310 ) with HYDROLIC seat

cover, with (B) flushing tank constellation cistern ( JOHNSON MAKEP0096P00019) with cistern fittings,

48 CI chair bracket with rag bolt and GI 12mm rag bolt with nut and metal washer etc. including supply and 3 Nos 18737.52

fixing of (C) 1 no CP heavy duty angle cock with CP wall flange with CP brass inlet connection with

integral P or S trap including cutting and making good the wall and floor as under with supported on CI

wall brackets and etc. complete to the satisfaction of EIC

providing and fixing Single Lever Tall Basin Mixer (Johnson T6146C) with on water supply pipe lines of

49 15mm dia with or with extension piece but with a flange etc. complete to the satisfaction of EIC and 2 Nos 6443.8

approved Johnson/ cera make.

providing and fixing Single Lever wall mount Tap (Johnson T6086C) with concealed body for wall

50 mounted (Johnson T0068C) with on water supply pipe lines of 15mm dia with or with extension piece but 1 Nos 6610.45

with a flange etc. complete to the satisfaction of EIC and approved Johnson/ cera make.

providing and fixing cp BRASS Bathroom 3 Inlet Single Lever High Flow Concealed Diverter make-

51 Johnson (T3439C) with conceled body (Johson T0066C) quarter turn of approved Johnson/ cera make 3 Nos 8865.78

and as approved by the consultants.

providing and fixing ocean square overhead shower with shower arm 1' long of (Square Shower Square

52 Shower Johnson (S0032C) 200 MM " or equivalent make on water supply pipe lines of 15mm dia. 3 Nos 3977.38

complete to the satisfaction of EIC and approved Johnson/ cera make.

providing and fixing hand shower (health faucet)( Johnson health faucet) (S3248C) " or equivalent make

53 Health Faucet with cp flange with 8 mm dia., 1 m long pvc tube and wall hook of approved by the 3 Nos 1599.84

consultants.

providing and fixing chrome plated controll valve CERA make (F8015102) on water supply pipe lines of

25mm dia with required fittings etc. complete to the satisfaction of EIC.

providing and fixing best Indian make mirror of specified size like modi float, saint gobain, i.a.g or

equivalent silvered locally, with plain edge as required, with 12mm thick marine plywood backing, with cp

brass caps, etc., complete teakwood beading of 20mm x 32mm size, with French polish or 3 coast of

paint etc. complete to the satisfaction of eic.

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden plugs with

C.P.brass scews.(B) 600mm x 20mm size.

57 Providing and fixing toilet paper holder.(A) C.P. Brass 3 Nos 528.99

Providing erecting and fixing double coated ISI water tank of required capacity each with all necessary

fittings and connection etc. complete on terrace.

Providing & constructing BB masonry in C.M. 1:6 (1 cement : 6 coarse sand) and cement concrete

1:2:4(1 cement : 2 sand : 4 graded stone age. of 0mm size BT kapchi) septic tank of 3m x 0.9 m x 1.5 m

internal dimension with necessary compartment of grit chambers and septic tank with necessary inlet and

outlet connections with cement plaster (15 mm thick) in C.M. 1:4 (1 cement : 4 sand) with water proofing

59 material 1:5:10 (1 cement : 4 sand) brick bat concrete bedding RCC 1:2:4 top cover slab 12 cm thick with 1 NOS 29934.38

C.I. cover of 60 cm x 45 cm size (light duty) 75mm dia. C.I. ventilating pipe 2 mt. long with cowl vent

40mm thick IPS flooring 10 cm. thick cement vata mild steel for steel and finishing to exposed faces in

C.M. 1:3 (1 cement : 3 sand) curing etc. complete As per Architect instructions and as directed by

engineer in charge.

Providing and constructing sock pit of 3.00 mt. dia inside and 5.00 mt. depth with honey combed masonry

60 6.50 mt. from bottom and 0.60 mt. brick masonry in C.M. 1:6 top with RCC slab cover of M200 vent pipe 1 NOS 59772.81

1.80 mt. long 75 mm dia & C.I. cover and cowl vent etc. complete

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with bricks

having crushing strength not less than 35Kg/ Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x

610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover

61 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone 3 NOS 7180.44

aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3

finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(iii) Inside

dimensions 600mm x 850 mm and 450mm deep for pipe lines with three or more inlets.

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover

62 with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps. (A) 100mm x 3 NOS 1292.19

100mm size P type.

providing and fixing Nirali make SS sink (460 x 385 x 200 mm) (Glister NG Glossy) with tapered sides

63 walls including 15 mm knob cp brass heavy quality wall or floor mounted sink tap Johnson make 2 NOS 7999.2

(T4818C), with cp wall flange, casted spout of three way etc. complete to the satisfaction of eic.

Charges for making holes in brick walls / RCC with or without plaster / tiles with mechanical cutter like

HILTI etc. Including disposing the debris and finishing the same as per requirements. Measurement of

holes will be taken per no. of holes drilled as per following range of diameters. Making of holes by

hammer and chisel will not be considered in this item. For Diameter of holes up to 100 mm clear.

Steel work, riveted in built up sections framed work including cutting, hoisting, fixing in position and

applying a priming coat of red lead paint. (A) In beams and joists, channels angles Tees, flats, with

connecting plates or angle cleats as in main and cross beams. Hip and jack rafters, purlins conneted to

common rafters and the like.

Providing and fixing square Roof Tiles having natural clay terracotta finish cladding used for both interior

and exterior as directed by EIC. Basic Rate : Rs.100/Sft

Providing and fixing Stone cladding work in Exterior wall including Fitting and scaffolding as directed by

EIC. Rs.300/Sft

Storage UNIT

Providing and fixing storage unit with 18 mm thick box and shutters from 25mm ply with 1.0 mm laminte

of approved shade in exterior side and0.8 mm laminte of approved shade in interior side vertical and

horizontal surface 19mm plywood with inside 0.8mm and outside 1mm laminate finish. provide one

18mm self with 0.8mm laminate .All teak wood bidding should be finished with 1mm leminate with

required pattern/drawing rack and with lock, handles ,drawer, chenals,, hinges etc. complete. Including

side luggage self of 75mm x 50mm size teak wood patti with pupolish completa . all materials and labor

etc. complete as per detail drawing and instruction of engineer- in charge.

Window Curtains :

Providing and fixing black-out roller blinds of "Aerolux" or equivalent make of any color and size for

windows, with super-soft mechanism using clutch and springs housed in aluminum channel fixed to the

69 masonry/ RCC surfaces by use of brackets. The fabric to be of 100% polyester yarn, cut of site-specific 24.8 SMT 2439.15

size cut using ultra-sonic machines to avoid threads coming out from its edges. The rubberized coating

over the fabric to enhance blacking out of the space. complete at all levels and heights.Complete or as

directed as per architect drawing and as per instruction of architect & engineer in charge.

6 SEATER DINING TABLE : Provide and supply Nilkamal Jewel Six Seater Dining Set (Walnut) dining

table of 1.50m length 0.90m width and 0.75 m height made of Solidwood and melamine finshed with PU

polish and 6 chairs 450 mm width 524mm length and 900mm height with 2" cusion as per drawing or

image provided by consultant and suggested by engineer in charge.

Three seated sofas

Providing and supplying Nilkamal Rippon 3 Seater sofa or equivalent make Width 209 cm (82.3" Inch),

Depth 82 cm (32.3" Inch), Height 92.5 cm (36.4" Inch), Seating Height 47.5 cm (18.7" Inch), springs

ensures exceptional comfort Elegant fabric and leatherette upholstery for luxurious comfort Circular

shaped armrests and tufted backrest with buttons add a touch of luxury Rose gold legs provide support

and a chic and modern aesthetic Built from robust MDF and Neem wood for enhanced durability.

CENTER TABLE:-Manufacturing and Supply of Center Table

Coffe table size 650 (L) x 650 (D) x 400 (H)

1. Wood Framing - Base frame round molded

25x50 mm Sq. thick CP teakwood duly polished

72 with mahogany melamine finished . 1 NOS 7221.5

2. Top Glass made of 10 mm thick clear toughen

glass with crystal edges .

3. Glass support shall be button fitted on all

corner.& have pvc buffers at bottom.

TV UNIT : (1.35 M X 0.25 M X 0.26 M) Provide and supply wall mounted tv made off 19mm ply and both

73 side side drawer and center portion empty, outer coverd with 1mm laminate and inside 0.80mm laminate 1 NOS 11665.5

of required shade as per drawing or image provided by consultant and suggested by EIC.

SLEEPING BED ( 1.95 m x 2.15 m x 0.37m)

Providing and fixing bed with 25mm ply with 1.0 mm laminte of approved shade in exterior side and0.8

mm laminte of approved shade in interior side vertical and horizontal surface 19mm plywood with inside

0.8mm and outside 1mm laminate finish provide with two openable shutter at top with handles. Also

provide six s.s. legs .All teak wood bidding should be finished with 1mm leminate and also provide two

side box (600 x 400 x 450mm) with each two drower made off 19mm ply, outer 1mm and inside 0.8mm

laminate etc complete with all materials and labor as per detail drawing and instruction of engineer- in

MATTRESS: (1.95M X 2.15 M X 0.15M) Provide and supply required size of mattress provide with

memory foam with removable and washable cover of sleepweel or eql. Make as suggested by EIC.

BED SHEET: (2.50 M X 2.30M) Provide and supply required size of pure cotton bedsheet of required

pattern and colour as suggested by eic.

PILLOW : (0.68 M X 0.45 M) Provide and supply required size of pillow made of microfiber of sleepweel

make or etc with it's cotton cover as suggested by EIC.

Earthwork in cutting including preparing the slope and camber andstacking or utilising the cutting stuff in

bank as directed upto 200 Meters from the end of cutting with all lead and lift.(i) Hard murrum.

Earthwork for embankment including breaking clods, dressing with all lead and lift (excluding watering

and consolidation)(A) From Borrow pits within land width

Rolling of earthwork in layers with power roller including filling in depressions which occur during the

process. With Watering of earth work as directed.

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length , in below type of pipe

erected with 6A Modular type switch / bell push & accessories and earth continuity of following type,

81 erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured/metallic/white 59 PT 481

front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling

rose / H.D.Connector as directed. (f) with medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete.Cat. III

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both

are of .ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires erected in below type of

pipe with 6A Modular type switches and following type of accessories erected on PVC / Metallic/Wooden

82 box, single mounting base frame covered with textured / metallic/white front plate modules erected on / in 6 PT 562

wall / ceiling as per pipe erected. with necessary batten/angle holder or ceiling rose or H.D.Connector as

directed.(a) with medium class Rigid PVC pipe and accessories erected flushed on wall/ceiling complete

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV

Grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected

with 6A Modular type switch and hum free EME step type electronic fan regulator mounted and

83 accessories with earth continuity of following type erected on PVC / Metallic/Wooden box, single 7 PT 668

mounting base frame covered with textured/metallic/white front plate modules erected on / in wall /

ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.(f) with medium class

Rigid PVC pipe and accessories erected concealed in wall/ceiling complete. cat III

Point wiring for Tissino / Modular secondary light point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires, in below type

of pipe to be erected complete with earth continuity and necessary connection with primary light with

accessories erected on Metal / PVC / wooden box covered with 3 mm thick PC(Polycarbonate) / Acrylic

sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories erected flushed on wall/ceiling complete

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC /

85 Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate 18 PT 255

modules erected on / in wall / ceiling with following type accessories Cat. III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with

86 appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of 3 PT 471

accessories.[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db

board (a) with medium class Rigid PVC pipe and accessories erected flushed on wall/ceiling

complete.Cat. III .)

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of

accessories.[II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db board.(a) with

medium class Rigid PVC pipe and accessories erected flushed on wall/ceiling complete Cat. III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge. Car.III

(1)One No. SP 6 Amp.

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge. Car.III

(2) One No 5 pin plug

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge. Car.III

(7) Blank Plate Single

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge. Car.III

(8) Computer RJ-45 socket

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge. Car.III

(9) 16 Amp. SP one way switch

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge. Car.III

(10) 6/16Amp. Universal socket

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge. Car.III

(13) 6A/10A/16A/20A/25A/32A Single pole Modular MCB Switch

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured / metallic/white front plate , modules erected with necessary

95 connections as per site situation directed by Engineer In charge. Car.III 15 Ea. 64

(24) Batten Holder/Angle Holder with modular frame with metal ring.

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be

erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive

solution & Clamps with following dia of pipes, in approved manner as directed

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be

erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive

solution & Clamps with following dia of pipes, in approved manner as directed

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq.

98 mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following 1000 Mtr 62

size.(A) With medium class Rigid PVC pipe and accessories

(a) 2 wire 1.5 sq. Mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq.

99 mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following 350 Mtr 82

size.(A) With medium class Rigid PVC pipe and accessories

(b) 2 wire 2.5 sq. mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size.(A) with

medium class Rigid PVC pipe and accessories. (a) 2 wire 4 sq. mm

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on

single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. & corrosion resistance with diffuser with

company mark/name 160V to 270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage

shown.) (A) Tube Light with integral driver (v) 36-40 Watts, Surge-2 KV, IP-20, conventional 4 feet cat-III

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on

single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage

shown.) (A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded

mounting clips complete.IP20 (iii) 16-20 watts, Surge-2 KV

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of

Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High

pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium

with diffuser and Polycarbonate optics/ lenses, with toughened glass with company mark/name engraved

or embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79

& LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED

Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply with over-voltage

protection. (iii) Above 60 to 90 watts

Providing & erecting Approved make Ceiling Fan with double ball bearing ISI mark with Condenser

volt A.C.50 Hz 1200 mm sweep complete having 3 blades aluminium body and blade sets having

ornamental design shanks , canopy erected with earthing. [ Make shall be approved by Engineer in

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted

for fan complete with proper insulation without leakage and earthing.

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm

106 length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected 5 Ea. 107

concealed in Ceiling with necessary finishing.

Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring

107 mounted low noise operation suitable for medium duty having following dia size and maximum speed in 3 Ea. 2034

RPM. [C] [A] 305 mm dia 900 RPM.Cat.ii

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for

108 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (C) 3 10 Mtr 282

1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core)

Making trench in soft soil of suitable width of 90 cm deep for laying cable or locating the fault all over the

run and back filling the same and making the surface as normal ground.

Covering of cable with second class bricks or cement tiles laid cover the cable crosswise & also on both

sides with covering of 7. 5 Cm. layer of sand above & below cable (16 bricks per meter)

Providing and erecting iron clad cable route marker duly marked with ELE.CABLE of size 23 cm.X 12 cm.

Flushed with ground in cement foundation as directed by Engineer in charge.

112 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 5 Kg 928

Supplying & erecting earth pit of minimum bore dia.150mm size approved make arthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-

250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable for following type of applications with chamber

and heavy duty cover.(approved make OEM has to submit test certificate) & having back filling

compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 meter testing as per IEC 62561-

2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill Compound :-

Earthing compound should be capable to retain moisture for long time Necessary test report must be

submitted.(b)For Electrical installation up to 11 KV in normal soil.

Length of Pipe : 2.00 mtrs

Back filling Compound :1 no. Bag of 25 Kg. )

Providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase 240 V,50Hz.

having characteristic of quick action & tripping with all advance feature & do not incorporate any

electronic component. for following Max. rating erected as directed.(iii) 63 Amps. DP Cat. III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box having following capacity. (c)63 Amp.

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA

breaking capacity & confirms to IS : 8828 in existing box having following capacity.(A) 6 to 32 Amp. Cat iii

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on 240 V A.C.

117 system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 15 Ea. 111

with ISI Mark Cat.III

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted

with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

118 MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) 2 Ea. 696

suitable for,(A) single phase incoming and horizontal single phase outgoing

(A) single phase incoming and horizontal single phase outgoing (iii)8 way

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted

with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

119 MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) 1 Ea. 859

suitable for,(A) single phase incoming and horizontal single phase outgoing

(A) single phase incoming and horizontal single phase outgoing(iv)12 way

Rupees Forty Nine Lakh(s) Forty Eight Thousand One Hundred Eight And Paise Ninety Three Only

Deputy Executive Engineer

Bhiloda Irrigation Sub Division