PROPOSED WORK FOR CONSTRUCTION OF COMMINITY HALL AT TPS NO- 8(RUVA) F.P. NO-30 AT RUVA (PHASE-II)

NAME OF Work : PROPOSED EXTENTION OF COMMUNITY HALL AT T.P.S NO :- 8 (RUVA) F.P. NO :- 30, AT :- RUVA, DIST :-

NAME OF DOCUMENT: Schedule - B

Rate Total Amount

Rate Total Amount

Item No. Item Description Quantity Unit

1) The method of excavation shall be approved by

the Engineer in charge before execution.

2) Excavation shall be carried out very carefully

without damaging existing structures and

surrounding if any.

3) If required, the contractor shall provide

stabilization by any means to protect the

foundation of the existing structure and building

without any extra cost.

4) Rate shall include dewatering work (pumping

out and removing slush) while execution in

underwater condition if required.

Excavation for foundation in any kind of soil incl.

sand, soft or hard marum, soft rock not requiring

Blasting incl. dewatering if required at cost and risk of

agency incl. shoring, struting, making the bottom level

and sides in plumb incl. watering, raming and

1 consolidating the bottom etc. incl. removing the 3.75 Cmt 211.23

surplus stuff and black cotton soil if any within all lead

and lift using the selected stuff for back filling to

foundation, in side trenches and plinth in layers of

cms. th. with watering, consolidating etc. comp. as

directed. (A) up to 1.50mt.

Boring holes 3.5 m deep in ordinary soil (for cast in

situ piles) and getting out the soil and disposal of the

surplus excavated soil as directed within a lead of

Meter for following diameter of pipes. (iii) 300 mm

Filling available excavated earth (excluding rock) in

trenches. plinth, sides of foundations etc. in layers not

exceeding 20 cm. in depth consolidating each

disposited layer by ramming and watering.

1) All types of shuttering shall be designed by the

contractor and submitted to the

Engineer-in-Charge along with design

calculations (if required) and approved by the

Engineer-in-Charge. However, the stability and

compatibility of shuttering shall be the

responsibility of the contractor. Shuttering shall

be executed as per the approved shop drawing.

No extra payment shall be made for the above.

2) Rate shall be inclusive of dewatering work

(pumping out and removing slush) while

execution in underwater conditions. The

contractor shall not claim for dewatering if

3) Rate shall be inclusive of providing grooves,

drip moulds, pockets, cut-outs, etc., and

co-ordination of insert sleeves, insert plates (cost

of insert sleeves/plate shall be paid separately),

encasing if any wherever required while casting

for all level all height.

4) With reference to the testing of piles on site,

following types of tests need to be done without

any extra cost:

a) Initial Load Test: Minimum 2 number of

separate Test Piles (other than foundation piles)

to be casted and tested in near vicinity. These

piles to be tested to maximum of ultimate load

and 2.5 times the estimated safe load. Report

shall be submitted to the Engineer-in-Charge from

authorized agency.

b) Routine Test: 1% of total piles (minimum

piles) to be tested for Compression, Tension, and

Lateral Capacity of piles separately, i.e. 2 for

Compression, 2 for Tension, and 2 for Lateral

Capacity of piles.

5) Only the following approved brands of cement

shall be used for all works: [ultratech], [sanghi],

[Siddhi], [Hathi] and [Ambuja]. Use of any other

brand shall not be permitted without prior written

approval of the Engineer-in-Charge.

6) If the concreting quantity is more than 5 cum in

a day, then the casting shall be carried out using

RMC (Ready Mix Concrete).

If the concreting quantity is 5 cum or less in a day,

then the casting shall be done manually.

All concreting work shall be carried out strictly as

per the advice and instructions of the

Engineer-in-Charge.

Providing and laying cement concrete 1:3:6

(1-Cement : 3- coarse sand : 6- hand broken stone

4 aggregates 40 mm nominal size) and curing complete 0.45 Cmt 3106.67

excluding cost of formwork in (A) Foundation and

Providing and laying in position Ready Mixed M-250

grade concrete for reinforced cement conctere work,

using cement content as per approved Design Mix

manufactured in fully automatic batching plant and

transported to site of work in transit mixer for a lead

up to 10 kms having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

5 R.M.C. from transit mixer to site of laying, including 1.46 Cmt 5727.96

the cost of centering, shuttering, finishing, admixtures

in recommended proportions as per IS: 9103 to

accelerate/ retard setting of concrete, improve

workability without impairing strength and durability

but excluding the cost of reinforcement as per

direction of the Engineer-in-charge. Without Fly Ash

(Min cement level as per latest IS 456 shall be

maintained) (A) Foundation

Providing and laying in position Ready Mixed M-250

grade concrete for reinforced cement conctere work,

using cement content as per approved Design Mix

manufactured in fully automatic batching plant and

transported to site of work in transit mixer for a lead

up to 10 kms having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

6 R.M.C. from transit mixer to site of laying, including 2.43 Cmt 9410.42

the cost of centering, shuttering, finishing, admixtures

in recommended proportions as per IS: 9103 to

accelerate/ retard setting of concrete, improve

workability without impairing strength and durability

but excluding the cost of reinforcement as per

direction of the Engineer-in-charge. Without Fly Ash

(Min cement level as per latest IS 456 shall be

maintained) (D) Columns

Providing and laying in position Ready Mixed M-250

grade concrete for reinforced cement conctere work,

using cement content as per approved Design Mix

manufactured in fully automatic batching plant and

transported to site of work in transit mixer for a lead

up to 10 kms having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

7 R.M.C. from transit mixer to site of laying, including 13.12 Cmt 6526.60

the cost of centering, shuttering, finishing, admixtures

in recommended proportions as per IS: 9103 to

accelerate/ retard setting of concrete, improve

workability without impairing strength and durability

but excluding the cost of reinforcement as per

direction of the Engineer-in-charge. Without Fly Ash

(Min cement level as per latest IS 456 shall be

maintained) (C) Coping and Beams

Providing and laying controlled cement concrete

8 M-250 for R.C.C. bored piles of 1.20 Mt. diameter 3.36 Cmt 4802.65

including ramming, vibrating and finishing complete.

Providing and laying in position Ready Mixed M-300

grade concrete for reinforced cement conctere work,

using cement content as per approved Design Mix

manufactured in fully automatic batching plant and

transported to site of work in transit mixer for a lead

up to 10 kms having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

9 R.M.C. from transit mixer to site of laying, including 27.59 Cmt 9602.41

the cost of centering, shuttering, finishing, admixtures

in recommended proportions as per IS: 9103 to

accelerate/ retard setting of concrete, improve

workability without impairing strength and durability

but excluding the cost of reinforcement as per

direction of the Engineer-in-charge. Without Fly Ash

(Min cement level as per latest IS 456 shall be

maintained) (D) Columns

Providing and laying in position Ready Mixed M-300

grade concrete for reinforced cement conctere work,

using cement content as per approved Design Mix

manufactured in fully automatic batching plant and

transported to site of work in transit mixer for a lead

up to 10 kms having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

10 R.M.C. from transit mixer to site of laying, including 85.23 Cmt 6718.60

the cost of centering, shuttering, finishing, admixtures

in recommended proportions as per IS: 9103 to

accelerate/ retard setting of concrete, improve

workability without impairing strength and durability

but excluding the cost of reinforcement as per

direction of the Engineer-in-charge. Without Fly Ash

(Min cement level as per latest IS 456 shall be

maintained) (C) Coping and Beams

Providing and laying in position Ready Mixed M-300

grade concrete for reinforced cement conctere work,

using cement content as per approved Design Mix

manufactured in fully automatic batching plant and

transported to site of work in transit mixer for a lead

up to 10 kms having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

R.M.C. from transit mixer to site of laying, including

the cost of centering, shuttering, finishing, admixtures

in recommended proportions as per IS: 9103 to

accelerate/ retard setting of concrete, improve

workability without impairing strength and durability

but excluding the cost of reinforcement as per

direction of the Engineer-in-charge. Without Fly Ash

(Min cement level as per latest IS 456 shall be

maintained) (C) Slabs, landing, shelves and

Providing TMT Bar CRS - FE 500D reinforcement for

R.C.C. work including bending, binding, placing in

12 position, hooking, tying welding and including forming 33193.33 Kg 77.29

the cage and lowering it in position etc. complete of

Specific brands - Tata Tisco/Vizag/ET/JSW/SAIL

1) Masonry work shall be carried out for all floors, all

levels, all heights, and all locations, including loading,

unloading, stacking, transporting, hoisting, and

erecting by any means (mechanical or manual)

2) Only the following approved brands of cement

shall be used for all works: [ultratech], [sanghi],

[Siddhi], [Hathi] and [Ambuja]. Use of any other brand

shall not be permitted without prior written approval of

the Engineer-in-Charge.

Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg./Sq.Cm.

13 in superstructure above plinth level upto floor two 128.73 Cmt 4599.16

level in Cement Mortar 1:5 (1- Cement : 5 -fine sand)

(B) Conventional

Half brick masonry in common brunt clay building

bricks having crushing strength not less than

14 Kg/Sq.Cm. in in superstructure above plinth level upto 27.18 Smt 683.87

floor two level in Cement mortar 1:4 (1- Cement :

-coarse sand ) (B) Conventional

1) All loose samples of materials shall be

approved by the Engineer in charge.

2) The contractor shall prepare shop drawings

based on intent/ concept drawing and get

approval from the Engineer-in-Charge. The

contractor shall prepare mock-up of doors,

windows, and other elements with all required

hardware and approved by the

Engineer-in-Charge before execution of work.

Work shall be carried out as per the final

approved shop drawing and approved mock-up.

The contractor shall be responsible against

stability, safety, leakage, etc all complete. Testing

work shall be carried out by the Contractor as

suggested by the Engineer in charge. (If required).

3) All Doors, windows, and other elements shall

be fabricated and finished at the factory/

workshop, and only fixing and final finishing shall

be executed at the site unless otherwise approved

by the Engineer-in-charge.

4) Door, window and other elements work shall be

carried out for all floor, all level, all height, all

places including loading, unloading, stacking,

transporting, hoisting, erecting by any means

(mechanical or manual).

5) Engineer incharge reserves right to reject part

or all work of sub standard or not in confirmation

to sample approved/or not as per mock up and in

such case contractor required to re do the same

work confirming with approved sample/mockup

without any extra cost. Approved mock up works

shall be measured for payment without any

wastage However, rejected Mock up shall not be

measured for payment.

Providing and fixing 35 mm thick flush door shutter

flat pressed wood based exterior grade bonded

BWP/BWR synthetic resin having stamped IS

grade I type II including both sides 1 mm thick

Decorative laminated and 6 mm thick I.T.W. beading

all around by using 120 m.m. x 80m.m.. solid core

malemine faced three layered I.T.W. frame with

15 necessary groove cutting and Stainless steel 20.68 Smt 4217.27

decorative type designs fixtures / fastening

2Nos.Satin Finish Mortise Handle with lock, towerbolt,

Floor door stopper, hinges etc. including I.T.W.

triangular batten patti of size 30m.m.x30m.m.etc. as

per architectural requirement and as directed by

engineer in charge. (Double Shutter)

Providing 30mm thick 100% Solid WPC (Wood

polymer Composite) Solid Plain (wooden figure)

Flush Door Shutter of required size comprising of

virgin PVC resin of K Value 57-60 (Suspension

Grade) with Door Frame 100 mm x 50 mm Single

Rebated made from Wood Polymer Composite

(Single Extruded Process) material comprising of

virgin PVC polymer of K Value 57-60 (Suspension

Grade), Calcium Carbonate and natural Fibers (Wood

16 Powders/ rice husk/ wheat husk) and Non toxic 14.08 Smt 5715.76

additives, made from Extrusion process WPC foam

sheet Single Extruded (Inner) For WC / Bathroom /

Toilet / Kitchen / Balcony Doors Including all required

hardware materials labours and equipments with

fixing as per approved sample detailed specification

as directed Engineer in charge with all lead and lift.

As per attached Detail specification. (including all

2Nos.Satin Finish Mortise Handle with lock, towerbolt,

Floor door stopper, hinges etc. complete)

Providing and fixing window having extruded

aluminum Colour anodized section frame main outer

size 95 mm x 24 mm x 1.17 mm @ wt. of

Kg/mt, horizontal Three track member size 92 mm x

31.75 mm x 1.30 mm, @ Wt. 1.07 Kg/mt, vertical

member of size 92 mm x 31.75 mm x 1.50 mm @ Wt.

1.06 Kg/mt with sliding shutters of horizontal member

size 40 mm x 18 mm x 1.29 mm @ wt. of

Kg/mt, vertical member of size 40 mm x 18 mm x

mm @ wt. of 0.456 Kg/mt / with 5 mm thick

transparent bronze colour tinted float glass with

powder coated aluminum fittings and fixtures and

transparent silicon sealant glass fixing to frame as per

Providing and fixing standared extruded of

alluminium section of size 63.50 x 38.10 x 1.95 mm @

Wt 1.094 Kg/Rmt with colour anodized alluminium

18 frame with 5 mm thick transparent bronze colour 4.56 Smt 1301.82

tinted float glass with colour anodized alluminium

frame for ventilation with 5 mm thick frosted glass as

details etc complete.

Providing and fixing Aluminium Framed & 12 mm

thick toughened glass door shutter of approved brand

and manufacture, including providing and fixing top &

bottom fitting arrangement and making necessary

holes etc. for fixing required door fittings, all complete

as per direction of Engineer-in-charge.

1) All types of loose and laid samples of flooring

shall be approved by the Engineer-in-charge.

The contractor shall apply approved Stone

Impregnation primer/ sealer coat on both sides

and all edges (after cutting and finishing the stone

as per size) of stones in a minimum of two coats

as per the manufacturer's specification and as

directed by the Engineer-in-charge. No extra shall

be paid for the same.

2) Contractor shall co-ordinate and execute for all

services in flooring and wall lining/ cladding work

i.e. making openings/ cut-outs for any services

(i.e. elevator operating panel in lift wall cladding,

raceway in flooring, junction box, etc), and

making good as per the satisfaction of

Engineer-in-charge.

3) Flooring and wall cladding/ lining work shall be

carried out for all floors, all levels, all heights, and

4) Rate shall be inclusive of all types of wastage

of all material.

5) Only the following approved brands of cement

shall be used for all works: [ultratech], [sanghi],

[Siddhi], [Hathi] and [Ambuja]. Use of any other

brand shall not be permitted without prior written

approval of the Engineer-in-Charge.

Providing and laying polished Kota stone slab flooring

over 20 mm (Average) thick base of cement mortar

1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5

20 (1-Limeputty : 1.5-coarse sand) laid over and jointed 7.80 Smt 1019.40

with grey cement slurry mixed with pigment to match

the shade of slab including rubbing and polishing etc.

complete. (A) 25mm thick

Providing and laying polished kota stone slab 25 mm

thick in risers of steps, skirting Dedo and pillars laid

on10 mm thick cement mortar 1:3 (1-Cement :

3-coarse sand) and jointed with gray cement slury

mixed with pigment to match the shade of slab

including rubbing and polishing etc. complete.

Providing and laying Polished Granite stone flooring

and skirting in required design, colour and patterns, in

linear as well as curvilinear portions of the building all

complete as per the architectural drawings with

mm thick stone slab over 20 mm (average) thick base

22 of cement mortar 1:4 (1 cement : 4 coarse sand) laid 153.95 Smt 3695.31

and jointed with cement slurry and pointing with white

cement slurry admixed with pigment of matching

shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the

Engineer-in-Charge.

Providing and fixing of minimum 16 mm thick

telephonic Black Granite stone slab for jambs of doors

and window. Black Granite should be spotless,

without any crack, vain or other damages joined with

grey cement slurry and matching pigment in vertical

and horizontal member, including rubbing and

polishing and full round edge molding on both the

sides( edge), Mirror polishing curing of the Black

Granite stone as per detail design and instruction.

The door frame should have sandwich type Jambs

23 stone fitting to accommodate fixing of door where 79.23 Smt 2571.06

required, the fixing of jambs with necessary binding

wire tiles piece, adhesive, clamp, fastener, white

cement and matching pigment other consumable,

molding and polishing machinery other tools, tackles

required to complete the item and where two member

vertical and horizontal meet it should cut 45 degree

angle etc up to all floor with all lead & lift etc

complete. The Black Granite stone size and quality

should be as per sample approved by architect and

Engineer in charge.

Providing and fixing 750 mm wide Granite sand

which type platform, counter wash basin including

supplying and fixing granite stone 18 mm thick mirror

polished 1st quality Granite stones in top and side

posiition and vertical strip at front over 25 mm thick

polished kotah stone platform fixing in top and sides

and itermediates supports fixing with cement mortar

and adhesivee and finishing including providing &

cutting of kitchen sink (as directed) 600 mm x 450 mm

x 150 mm size stainless steel sink (as directed by

engineer incharge) at required position etc complete.

Providing and laying coloured glazed tiles of the size

1200 mm x 600 mm x 8 mm in skirting, risers of steps

25 and dedo on 10 mm. thick cement plaster 1:3 (1 229.08 Smt 1523.67

cement : 3 coarse sand) & jointed with white cement

P & L 48" x 24" vitrified 8 mm thick tile flooring over

mm (average) base of cement mortar 1:6 ( 1 cement:

6 coarse sand) on new surface or fixing on existing

26 flooring by adhesive material including dismentaling of 400.21 Smt 1472.92

existing flooring and jointed with color cement slurry

including finised with flush pointing & cleaning the

surface etc. complete for antiskid

1) Contractor shall correlate all services drawings

from different installers and prepare a clash free

shop drawing as per the architectural drawings

for RCP, with all services integrated, vis a vis

HVAC, FFTG, PLUMBING, ELE, ELV & any other

services planned and part of the design.

2) The method statement for execution of all

services coordinated with the ceiling execution

shall be submitted by the Contractor for approval

of the Engineer-in-charge before commencing

execution work at site.

3) Quality check and sequence of execution along

with relevant documentation to be ensured by the

site project team for inspection and quality

4) The false ceiling work to be strictly supervised

for alignment, line & level and overall quality of

installation and the Contractor to strictly follow

the approved methodology statement.

5) The false ceiling suspension work shall be

strictly from the mother slab or secondary

supports installed for the false ceiling and not

from any suspension members of other services.

6) All services equipment & light fixtures, curtains

etc. to be fixed with a separate suspension

system from the mother slab, not on the false

ceiling tiles or false ceiling members.

7) For gypsum ceilings, the Contractor shall

provide perimeter channels at the periphery of all

services cutouts for strengthening the system.

8) If required, additional supports to be provided

for fixing the false ceiling (in case of special

shape, more height etc).

9) In case the height of suspension system is

more than what is recommended by the

manufacturer, separate MS supports to be

provided from the mother slab and the false

ceiling to be suspended from the MS supports.

Design and shop drawing for the MS fabrication

work and connections with the structure members

shall be submitted by the Contractor for approval

by the Engineer-in-charge. MS framework to be

designed to accommodate other services, if

required. Such MS frame work shall be paid under

relevant Tender items.

10) The sequence of execution of the different

services to be aligned with the RCP to avoid any

11) Movement joints/groove to be provided in the

boards or grid ceiling system in large span areas.

12) Contractor to quote the rate considering all

points mentioned in the specifications.

Providing and fixing eco-friendly light weight calcium

silicate false ceiling tiles having Tegular edge &

mm Thick Densified edges on the Tile Periphery for

Extra Strength The Light weight calcium silicate

ceiling tiles shall have , light reflection 85%

non-combustible as per B.S. 476 part IV, 100%

humidity resistance and also having thermal

conductivity0.043° w/m KC.for the best thermal

Insulation . The Light weight calcium Silicate tile shall

be of approved texture Fine fissured/

Spintone/Cosmos having NRC value of 0.5 & Globe

having NRC value of 0.75 NRC or equivalent of size

595 X 595 mm to be laid on true horizontal level

suspended inter locking metal grid of hot dipped

galvanized steel sections (galvanizing @120 grams

per sqm including both side) consisting of main ‘T’

runner suitably spaced at joints to get required length

and size of 24X38mm made from 0.30 mm thick

(minimum) sheet, 1200mm centre to centre, and

cross ‘T’ of size 24X28mm made out of 0.33mm

(Minimum) sheet spaced 1200mm along spaced

between main ‘T’ at 600mm centre to centre to form

agrid of 1200X600mm and secondary cross ’T’ of

length 600mm and size 24x28mm made of 0.30 mm

thick (Minimum) sheet to be interlocked at middle of

the 1200X600mm panel to form grid of size

600X600mm resting

on periphery walls/partitions on a perimeter wall angle

pre-coated steel of size (24X24X3000mm made of

0.40mm thick (minimum) sheet with the help of rawl

plugs at 450mm centre to centre with 25mm long dry

wall screws @ 230mm interval and laying 15mm thick

Densified edges light weight calcium silicate ceiling

tiles of approved texture (Fine

Fissured/Cosmos/Spintone) in the grid including,

cutting /making opening for services like diffusers,

grills, light fittings, fixtures, smoke detectors etc.,

wherever required, Main ‘T’ runners to be suspended

from ceiling using G.I. slotted cleats of size

25X35X1.6mm fixed to ceiling with 12.5mm dia and

50mm long dash fasteners, 4mm G.I. adjustable rods

with galvanized steel level clips of size

85X30X0.8mm, spaced at 1200mm

centre to centre long main ‘T’ bottom exposed with

24mm of all T-sections shall be prepainted with

polyester baked paint, for all heights, as per

specifications, drawings and as directed by

engineer-in-charge.Note:- Only calcium silicate false

ceiling area will be measured from wall to wall. No

deduction shall be made for exposed frames/opening

(cut outs) having area less than 0.30 sqm. The

calcium silicate ceiling tiles shall have NRC. Value of

0.50 (Minimum) for Fine fissured/Spintone/Cosmos

and 0.75 NRC for Globe, light reflection 85%

non-combustible as per B.S. 476 part IV, 100%

humidity resistance and also having thermal

conductivity. 0.043° w/m KC.for the best thermal

Providing and fixing gypsum board false ceiling

consists at G.I perimeter channels of size 0.55 thick

having one flange of 20 mm and another flange of

mm and web of 27 mm along with perimeter of ceiling,

screws fixed to brick work / concrete / partition with

help of nylon sleeves and screws at 610 mm centre.

The suspending G.I. intermediate channels of size

mm(0.9 mm thick with 2 flangs at 15mm each from

the soffit at 1220 mm centrewith ceiling angles of

width 25mm x 10mm x 0.5 mm thick fixed to soffit

withG. I cleat and steel expansion fastners ceiling

section of .55 thick having kurled web 51.5 mm and

flangs at 26 mm each with lip at 10.5 mm are fixed to

intermediate channel with help of connecting clips and

in direction perpendicular to the intermediate channel

at 450mm centre to centre including 12.5 mm tapered

edge Gyp board conforming to IS 2095 – 1982 is then

screw fixed to ceiling section with 25mm dry wall

screws of approved quality and make at 230mm

centre, screw fixing is done mechanically with drilling

machine with suitable attachment. Finally tapered

edges at the cupboard are to be joint and finished so

as to have a flush look which includes filling and

finishing with jointing compound, paper tape etc.

complete. Rate to be included all kinds of profiles,

upright, curves,cutouts required for light fixtures,

speakers, sprinklers, smoke detectors, trap doors,

A.C. grill, diffuser etc including additional support if

required of duct portion, marking grid on ceiling,

including all drops, offsets, curvature small moulding

and in desired geometrical pattern, including 2 coats

of primer, plaster putty and minimum 3 coats of plastic

Emulsion paint as per manufactures specification,

scaffolding. Note:-As per drawings and design

supplied by architect and instruction given by

authority and E.I.C.

Providing and fixing moisture proof Calcium Silicate

Board false ceiling consists at G.I perimeter channels

of size 0.55 thick having one flange of 20 mm and

another flange of 30 mm and web of 27 mm along

with perimeter of ceiling, screws fixed to brick work /

concrete / partition with help of nylon sleeves and

screws at 400 mm centre. The suspending G.I.

intermediate channels of size 45 mm(0.9 mm thick

with 2 flangs at 15mm each from the soffit at

mm centrewith ceiling angles of width 25mm x 10mm

x 0.5 mm thick fixed to soffit withG. I cleat and steel

expansion fastners ceiling section of .55 thick having

kurled web 51.5 mm and 2 flangs at 26 mm each with

lip at 10.5 mm are fixed to intermediate channel with

help of connecting clips and in direction perpendicular

to the intermediate channel at 450mm centre to

centre including 8 mm tapered edge alcium Silicate

Board conforming to IS 8154 – 1993 is then screw

fixed to ceiling section with 25mm dry wall screws of

29 approved quality and make at 200mm centre, screw 53.86 Smt 1254.71

fixing is done mechanically with drilling machine with

suitable attachment. Finally tapered edges at the

cupboard are to be joint and finished so as to have a

flush look which includes filling and finishing with

jointing compound, paper tape etc. complete. Rate to

be included all kinds of profiles, upright,

curves,cutouts required for light fixtures, speakers,

sprinklers, smoke detectors, trap doors, A.C. grill,

diffuser etc including additional support if required of

duct portion, marking grid on ceiling, including all

drops, offsets, curvature small moulding and in

desired geometrical pattern, including 2 coats of

primer, plaster putty and minimum 3 coats of plastic

Emulsion paint as per manufactures specification,

scaffolding. Note:-As per drawings and design

supplied by architect and instruction given by

authority and E.I.C.

1) Rate shall be inclusive of any type of groove

and drip mould in all type of plaster work.

2) The rate shall be for all height, all level in any

3) Curing method shall be approved by Engineer

4) Contractor shall provide mesh/ natural fibres

i.e. jute, core at junctions, corners, surround

electrical cut-out, services chiselled area etc.

5) Engineer incharge reserves right to reject part

or all work of sub standard or not in confirmation

to sample approved/or not as per mock up and in

such case contractor required to re do the same

work confirming with approved sample/mockup

without any extra cost. Sample and mock shall not

be payable if rejected or casted in other location

(not in scope of work area).

6) In all plaster work, chicken mesh shall be

provided at the junctions of masonry and

concrete works to prevent cracks. The mesh shall

be properly fixed and embedded before

plastering, and the finishing shall be done smooth

and even, as per the instructions of the

Engineer-in-Charge. (The cost of providing and

fixing chicken mesh shall be paid separately as

per the relevant tendered item rate.)

7) Only the following approved brands of cement

shall be used for all works: [ultratech], [sanghi],

[Siddhi], [Hathi] and [Ambuja]. Use of any other

brand shall not be permitted without prior written

approval of the Engineer-in-Charge.

Providing throating or plaster drip and moulding to

R.C.C. Chhajja.

31 Provideing & fixing Chicken wire mesh with plaster 100.00 Smt 184.03

Providing 10mm thick cement plaster in single coat on

brick/concrete walls for interior plastering upto floor

two level and finished even and smooth in (i)Cement

mortar 1:3 (1-cement:3-sand)

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for

33 interior plastering upto floor two level and finished 944.50 Smt 176.15

even and smooth in (ii) Cement mortar 1:4 (1-cement

20mm thick mala / sand faced cement plaster on

walls upto height 10 metres above ground level

34 consisting of 12mm thick backing coat of C.M. 1:3 737.87 Smt 350.58

(1-cement : 3-sand) and 8mm thick finishing coat of

C.M. 1:1 (1-cement : 1-sand) etc. complete.

1) Contractor shall prepare shop drawing base on

concept design/ drawing for any type of

fabrication work and get approved. Contractor

shall prepare mock-up/ prototype (as suggested)

as per approved shop drawing for approval. Work

shall be carried out as per approved shop

drawing, approved mock-up/ prototype and as

suggested by Engineer in charge.

2) Rate shall be for all floor, all level all height.

3) The rate shall include cost of all types of

fasteners (ETA approved) to be used for fixing.

4) Structural stability shall be responsibility of

contractor for all kind of metal work.

5) All elements shall be factory fabricated and

finished, only final finishing to be made on site

with all precautions.

6) Contractor shall coordinate all services work

(cut-outs and provisions) in metal work. All

cut-out and services provisions shall be finished

at factory/ work shop.

7) Contractor shall provide PVC/ nylon separator,

where two different metals connect to avoid

galvanic reactions.

Providing, fabricating, assembling, hoisting/ erecting

and fixing in position at all heights/ all shapes & sizes

with all leads & lifts using MS Rolled Steel Sections,

Hollow sections, MS Plates/ sheet, Flats, Bright Bars,

Anchor bar, deep threaded MS bolts, threaded J bolts,

insert plate, support plate etc as per drawing and all

confirming to latest relevant IS codes for steel

structures like staircases, railings, handrail, pergola,

decorative gate, grills, platforms, brackets, monkey

ladder or similar etc. including straightening, cutting,

bending, bolting and welding the members,

scaffolding/ staging etc. complete and comprising of :

i) Profile Cutting of components to required length/

width and shape/ profile;

ii) Smooth grinding/ machining of edges/ faces/ all

welding joints;

iii) Necessary welding (electric arc welding) in

35 required weld length and size; 3596.80 Kg 103.57

iv) Machine drilling of holes for joining/ anchoring

Standard measurements will be paid for as actual cut

length used at site. The rate shall include dry sanding,

degreasing (wet cleaning) & preparation of rust free

surface manually or mechanically, metal putty to make

the surface even and smooth, 2 coat zinc chromate

yellow oxide primer and 2 coat of enamel paint of

approved make, shade and finish over all the surfaces

of the steel sections.

Note: The contractor shall be submit shop/ fabrication

drawings based on construction drawings for approval

from the Architect and Engineer in charge. The

fabrication work shall start only after approval of the

fabrication drawings submitted by contractor.

Fabrication shall be in a perfect architectural

workmanship manner and as provided in section V &

1) Paint shall be applied after thoroughly brushing

the surfaces, free from mortar dropping and other

foreign matter, preparing the surface even and

sand papered smooth etc, after applying every

coat of putty and primer complete.

2) If necessary more coats shall be applied till the

surface presents a uniform appearance without

any extra cost.

3) Paint shall be applied with any means (i.e.

brush, roller, spray etc)

4) Contractor shall prepare sample of minimum

three shades as suggested by engineer in charge

5) The rate shall be applicable for all floor, all

level, all height by any means of scaffolding.

6) emultion paint quality should be simmiler of -

asian paints premium emulsion, dulux velvet

touch, Berger Silk

7) Exterior paint shall be applied over a

waterproof primer of approved make, as directed

by the Engineer-in-Charge.

Providing and applying external finish of average 2 to

2.5mm thick acrylic polymer based texture Plaster

Terre Plaette and pattern with standard tool and

applicator as specified by manufacturer on exterior

surfaces at all heights including scaffolding to give

even shades including thoroughly brushing the

surfaces free from mortar droping and other foreign

matter and sand paper smoothed etc. complete as

per the manufacture specifications and up to the

satisfaction of Engineer in-charge/ Architect. The rate

includes making of grooves, pattas and finishing as

directed by Architect/ EIC. Paint shall be measured

and paid in seperate tender item. (Item should be

executed by approved applicator only.)

Applying two coats of putty & two coats of primer of

approved brand and manufacture on new wall surface

37 to give an even shade including thoroughly brushing 1507.69 Smt 40.60

the surface free from mortar dropping and other

foreign matter and sand papered smooth.

Wall painting (two coats) with emulsion paint of

approved brand and manufacture on undecorated

38 wall surface to give an even shade including throughly 1507.69 Smt 84.82

brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth.

Finishing wall with weather proof exterior emulsion

paint on wall surface (two coats) to give an required

39 shape even shade after thoroughly brushing the 737.87 Smt 122.14

surface to remove all dirt, and remains of loose

powdered materials. etc complete

1) All the waterproofing treatment/ work shall be

executed through an approved water-proofing

agency of an approved manufacturer. The

contractor shall submit a technical data sheet of

each product, which will be used for execution.

2) The contractor shall submit a methodology

statement with all details in illustrative sketch

form and get approved by the Engineer-in-charge.

3) Waterproofing shall be executed under the

supervision of the technical team of the

manufacturer. Waterproofing shall be tested and

approved by the Engineer-in-charge before

proceeding with subsequent activities.

4) The Contractor shall repair the concrete

element by injection grouting of suitable

non-shrink grout and other suitable methods in

case of defective concreting of retaining walls,

water tanks, slabs, beams, etc., for which nothing

extra shall be payable.

5) Rate shall be inclusive of surface preparation,

repairing, injection grouting, saw cutting of

construction joints and filling with patch repair

mortar, making polymer mortar /Polymer CC fillets

at horizontal as well as vertical corners, etc

complete. The rate shall be inclusive of testing of

elements and system before and after

waterproofing application.

6) The latest technical system/ product shall be

adopted at the time of execution.

Providing and laying water proofing treatment on

roofs of slabs by applying cement slurry mixed with

water proofing cement compound consisting of

(a) after surface preparation, first layer of slurry of

cement @ 0.488 kg/ sqm mixed with water proofing

cement compound @ 0.253 kg/sqm.

(b) laying second layer of Fibre glass cloth when the

first layer is still green. Overlaps of joints of fibre cloth

should not be less than 10 cm.

40 (c) third layer of 1.5 mm thickness consisting of slurry 563.19 Smt 695.79

of cement @ 1.289 kg/sqm mixed with water proofing

cement compound @ 0.670 kg/sqm and coarse sand

@ 1.289 kg/sqm. This will be allowed to air cure for

hours followed by water curing for 48 hours. The

entire treatment will be taken upto 30 cm on parapet

wall and tucked into groove in parapet all around.

(d) fourth and final layer of china mosaic (which will

be paid for separately.

For the purpose of measurement the entire treated

surface will be measured.

Providing and laying broken chine mosaic flooring for

terrace using 12 mm to 20 mm broken pieces of

glazed tiles to be laid over cement mortar 1:3 to plain

or slope and to be tempered to bring mortar creme

out upto surface using white cement including

rounding off junctions and extending them upto 15 cm

along the wall, clearing with water and oxalic acid etc.

Providing and fixing 25 mm thick decorative polyester

acoustic wall panels, manufactured from 100%

polyester fibre, having density in the range of

100–240 kg/m³ (±10%), of approved colour, texture,

pattern and finish, with square/bevelled/mitred edges

as required. The 25 mm thick acoustic panel shall

have NRC 0.70 (without air gap), with sound

absorption coefficients approximately 0.07 at 125 Hz,

at 2000 Hz and 0.98 at 4000 Hz. Panel shall have

42 Class ‘A’ Fire Rating as per ASTM E-84 Tunnel Test. 112.56 Smt 2951.67

Panels shall be fixed directly onto the prepared

wall/substrate using manufacturer-recommended

adhesive, including necessary cutting to required

sizes/patterns, making openings for

electrical/services, edge finishing, proper joint

alignment, adhesive, wastage, scaffolding, labour,

tools and all necessary accessories, complete as per

approved drawings, manufacturer's specifications and

directions of Engineer-in-Charge. includeing plywood

Providing, supplying, installing, testing and

commissioning of decorative wall-mounted cascading

water fountain/water feature, comprising SS-304

water distribution channel/weir for uniform sheet flow

of water over approved stone/tile finished wall

surface, bottom water collection trough/tank with

complete waterproofing treatment, suitable

43 recirculation pump, filter/strainer, UPVC/PVC suction 1.00 Each. 89667.80

and delivery piping, valves, fittings, drainage/overflow

arrangement, waterproof LED illumination, electrical

connections, necessary supports, fasteners and

accessories, including cutting, fixing, plumbing, wiring,

testing and commissioning, complete in all respects

as per approved design and directions of

Engineer-in-Charge.

1) All natural stones shall be free from cracks,

lines, stains, and white spots of efflorescence,

and even in shade for all kinds of stonework.

2) All natural stones shall be selected and sorted

for uniform colour, figure, and thickness and

approved by Engineer-in-charge prior to

3) All natural stones shall be from the same lot

and/ or source (stone quarry) for the same kind of

work to avoid shade variation and as approved by

the Engineer-in-charge.

All types of loose and laid samples of flooring

shall be approved by the Engineer-in-charge.

The contractor shall apply approved Stone

Impregnation primer/ sealer coat on both sides

and all edges (after cutting and finishing the stone

as per size) of stones in a minimum of two coats

as per the manufacturer's specification and as

directed by the Engineer-in-charge. No extra shall

be paid for the same.

4) Contractor shall co-ordinate and execute for all

services in flooring and wall lining/ cladding work

i.e. making openings/ cut-outs for any services

(i.e. elevator operating panel in lift wall cladding,

raceway in flooring, junction box, etc), and

making good as per the satisfaction of

Engineer-in-charge.

5) Flooring and wall cladding/ lining work shall be

carried out for all floors, all levels, all heights, and

6) Rate shall be inclusive of all types of wastage

of all material.

7) Only the following approved brands of cement

shall be used for all works: [ultratech], [sanghi],

[Siddhi], [Hathi] and [Ambuja]. Use of any other

brand shall not be permitted without prior written

approval of the Engineer-in-Charge.

Providing and laying Polished Rajula slat stone work

on wall top / flooring in required colour, design and

patterns, in linear as well as curvilinear portions all

complete as per the architectural drawings with

mm thick stone slab over 20 mm (average) thick base

44 of cement mortar 1:4 (1 cement : 4 coarse sand) laid 1.00 Smt 2613.60

and jointed with cement slurry and pointing with white

cement slurry admixed with pigment of matching

shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the

Engineer-in-Charge.

Providing and fixing Rajula slat stone work (polished

and machine cut) of thickness 20 mm for wall lining

(veneer work) in linear as well as curvilinear portions,

backing filled with a grout of average 12 mm thick in

45 cement mortar 1:3 (1 cement : 3 coarse sand), 1.00 Smt 4563.03

including pointing with white cement mortar 1:2 (1

white cement : 2 stone dust) with an admixture of

pigment to match the stone shade etc. all complete as

specified and as directed by the Engineer-in-Charge.

1) Pipes and fittings shall be ISI marked and of

2) Pipes & fittings shall be of specific brands like

Supreme Industries Ltd, Prince Pipes & Fittings

Ltd, Finolex Industries Ltd, Astral Limited and

other similer brands as per approval of

Engineer-in-Charge.

3) Valves, cocks, traps and fixtures shall be of

standard quality and as per Engineer-in-Charge’s

4) All pipelines shall be laid true to line, level, and

properly supported.

5) Concealed lines shall be pressure-tested before

plastering/ finishing.

6) Traps and fittings shall be fixed with proper

alignment and water seal.

7) Openings and chases for pipes shall be made

good after installation.

8) Water supply lines shall be hydraulically tested

to required pressure.

9) All rates shall be inclusive of material, labour,

scaffolding, cutting, chasing, testing, and making

10) Work shall be carried out strictly as per

manufacturer’s instructions and direction of

Engineer-in-Charge.

Providing and fixing wash down wall mounting

EWC-P of approved shade, conforming to Pattern 2 of

IS: 2556 (Part -II), with SWR Self it Soil PVC pipe and

plug bend as per specifications; glazed vitreous /

Coloured European Water Closet with Metropole flush

valve, connecting PVC 110mm dia soil pipe with PVC

coupling, nuts, Ragbolt, Gasket Fitiiing and solid

46 verity heavy duty plastic seat cover as per IS-2548, of 8.00 Each 17405.03

approved make; hole in walls/slab/beam and making

good etc. complete as per directed by the Engineer's

Representative.

W.C Wall Hung : Jaquar, Model No. :

CNS-WHT-963UFSM

Metropole flush valve : Jaquar, Model No. :

Providing and fixing in position 15 mm C.P. brass bib

cock of best quality including cutting and making good

47 the wall where required etc. complete as per directed 8.00 Each 2624.08

by the Engineer's Representative.

Bib Cock : Jaquar, Model No. : OPP-CHR-15037PM

Providing and fixing 15mm C.P. brass angle valve with

wall flange complete, including cutting and making

48 good the wall where required etc. complete as per 8.00 Each 1737.30

directed by the Engineer's Representative.

Angle Valve :Jaquar, Model No. : OPP-CHR-15053PM

Providing and fixing of Hand Shower (Health Faucet),

with 8mm Dia,1Rmt Long pvc Tube and Wall Hook

49 accessories to .complete the item etc. complete as 8.00 Each 1838.68

per directed by the Engineer's Representative.

Health Faucet :Jaquar, Model No. : ALD-CHR-565

Providing and fixing White glazed vitreous Oval Wash

Basin WALL HUNG, size 560x430x195 mm., with

supporting M.S. or C.I. Brackets, necessary pipe

connection up to the outside face of the wall, Waste

coupling 32 mm size full thread with 80 mm height

Chrome plated, Bottle trap Chrome plated

Pressmatic Pillar Cock including necessary fittings

50 with wall Flange etc. complete in all respects including 8.00 Each 8746.74

cutting and making good the walls etc. complete as

per directed by the Engineer's Representative.

Wash basin : Jaquar, Model No. : CNS-WHT-811

Waste coupling : Jaquar, Model No. :

ALD-CHR-705L130

Bottle trap : Jaquar, Model No. :

ALD-CHR-769L300X190

Providing and fixing of C.P. copper connecting pipe

450 mm long and nuts, washer and brass flange

complete, including cutting and making good the wall

51 where required etc. complete as per directed by the 8.00 Each 459.55

Engineer's Representative.

Braided Hose Copper Pipe : :Jaquar, Model No.

Providing and fixing Pressmatic Pillar Cock of best

quality necessary fittings with wall Flange etc.

complete in all respects including cutting and making

52 good the walls etc. complete as per directed by the 8.00 Each 2772.91

Engineer's Representative.

Pressmatic Pillar Cock : Jaquar, Model No. :

Providing and fixing Long Body Bib Cock with Wall

Flange best quality including cutting and making good

the wall where required etc. complete as per directed

by the Engineer's Representative.

Long Body Bib cock : Jaquar Continental, Model No:

OPP-CHR-15037PM

Providing and fixing white vitreous china flat back

Urinal of size 385x325x635mm as per IS-2556

(Part-2) with C.I. hangers and pipe to wall with C.P.

flange with AUTO CLOSING CONCEALED Type

Urinal flush valve, complete including cutting and

54 making good the walls wherever required etc. 5.00 Each 14069.45

complete as per directed by the Engineer's

Representative.

Urinal :Jaquar, Model No. :URS-WHT-13253N

Urinal Flush valve ,Jaquar, Model No. :

Providing and fixing in position best Indian make toilet

recessed type paper holder complete in all respects

including cutting and making good the walls etc.

55 complete as per directed by the Engineer's 8.00 Each 1585.84

Representative.

Toilet Paper Holder : Jaquar, Model No.

Providing and fixing in position best Indian make C.P.

brass twin way QUOTE and hat hooks fixed into wall

with C.P. Brass screws and rawlplugs etc. complete

including cutting and making good the walls etc.

complete as per directed by the Engineer's

Representative.

Twin Way coat Hook: Jaquar, Model No.

Providing and fixing electrical hand dryer, fully

automatic type etc. complete as per directed by the

Engineer's Representative.

Hand Dryer : Jaquar, Model No. :HDR-SSF-AK2803D

Providing and fixing C.P. brass liquid soap container

of best quality etc. complete as per directed by the

58 Engineer's Representative. 6.00 Each 1433.76

Liquid Soap Container : Jaquar, Model No. :

SDR-WHT-DJ0010F

Providing and fixing of 2 way Single Lever Diverter

Mixer including of Concealed Fitting with Built in Non

return Valve , concealed stop cock for hot and cold

water supply controlling with Diverter Handle with

Spout and overhead shower etc. complete as per

directed by the Engineer's Representative.

Diverter, Make : Jaquar, Model :

59 KUP-CHR-35065NKPM 2.00 Each 15317.99

Concealed body for Diverter : Jaquar, Model :

Shower head, Make : Jaquar, Model :

Shower arm, Make : Jaquar, Model :

SHA-CHR-455L400

Spout, Make : Jaquar, Model : SPJ-CHR-35429PM

Providing & fixing stainless steel recessed type soap

dish of approved make. Including providing & fixing

screws, washers, cutting & making good the walls etc.

complete as per directed by the Engineer's

Representative.

Soap Dish : Jaquar, Model No. : ACN-CHR-1131N

Providing and fixing towel rail of approved make

including, providing and fixing C.P. brass screws,

61 making holes in walls and making good etc. complete 2.00 Each 1560.49

as per directed by the Engineer's Representative.

Towel Rail : Jaquar, Model No. : ACN-1111BNM

Providing and fixing of Handicap toilet cruse set

complete set including EWC, Flushing cistern, soft

close seat cover, twin flush fitting, Washbasin, single

lever basin mixture, wall mounted grab bar, wall

mounted hinged handrail, bottle trap including jointing

62 the trap with soil pipe in cement mortar 1:1 (1 cement 1.00 Each 50335.37

: 1 fine sand) including providing and fixing plastic

seat cover for wash down W.C. with C.P. brass hinges

and rubber buffers white plastic seat and jet spray

including cutting holes in walls and making good etc.

complete as directed by Engineer In Charge.

Providing and fixing 600mm x 450mm bevelled edge

mirrror of superior glass mounted on 6mm thick A.C.

sheet or plywood sheet and fixing to wooden pluge

with C.P. brass screws and washers.

Providing and fixing brass screw down stop tap.(A)

Providing and fixing brass screw down stop tap.(B)

Providing and fixing brass screw down stop tap.(C)

Providing and fixing Gun metal check or non-return

fullway wheel valve.(A) 15mm dia.

Providing and fixing Gun metal check or non-return

fullway wheel valve.(B) 20mm dia.

Providing and fixing Gun metal check or non-return

fullway wheel valve.(C) 25mm dia.

Providing and fixing Gun metal check or non-return

fullway wheel valve.(D) 32mm dia.

Providing and fixing Gun metal check or non-return

fullway wheel valve.(E) 40mm dia.

Providing and fixing C.I. Manhole cover 0.60 M. x

0.45M. size having weight not less than 35Kg.

Providing and fixing cast iron steps of size 500mm x

73 150mm x 22.5mm and painting with two coats of 0.00 Each 155.11

Anti-corrosive paint etc. complete.

Providing and fixing concealed center point to wall

ceiling & floor CPVC (SDR 13.5) PIPE having

National Sanitation Foundation (NSF) seal for potable

water of following dia. nominal bore tube fittings and

clamps including making good the wall, ceiling and

floor etc. complete.[A] 15 mm.

Providing and fixing concealed center point to wall

ceiling & floor CPVC (SDR 13.5) PIPE having

National Sanitation Foundation (NSF) seal for potable

water of following dia. nominal bore tube fittings and

clamps including making good the wall, ceiling and

floor etc. complete. [B] 20 mm.

Providing and fixing concealed center point to wall

ceiling & floor CPVC (SDR 13.5) PIPE having

National Sanitation Foundation (NSF) seal for potable

water of following dia. nominal bore tube fittings and

clamps including making good the wall, ceiling and

floor etc. complete. [C] 25 mm.

Providing and fixing concealed center point to wall

ceiling & floor CPVC (SDR 13.5) PIPE having

National Sanitation Foundation (NSF) seal for potable

water of following dia. nominal bore tube fittings and

clamps including making good the wall, ceiling and

floor etc. complete. [D] 32mm.

Providing and fixing concealed center point to wall

ceiling & floor CPVC (SDR 13.5) PIPE having

National Sanitation Foundation (NSF) seal for potable

water of following dia. nominal bore tube fittings and

clamps including making good the wall, ceiling and

floor etc. complete. [E] 40mm.

Providing and fixing concealed center point to wall

ceiling & floor CPVC (SDR 13.5) PIPE having

National Sanitation Foundation (NSF) seal for potable

water of following dia. nominal bore tube fittings and

clamps including making good the wall, ceiling and

floor etc. complete. [F] 50mm.

Providing and fixing Gun metal check or non-return

fullway wheel valve.(C) 25mm dia.

Providing and fixing Gun metal check or non-return

fullway wheel valve.(E) 40mm dia.

Providing, laying and jointing in true line and level

diametre U.P.V.C (Type B) conforming to IS

13592-1992 with one end plain and other end

socketed with rubber ring, & fittings conforming to ISI

14735-1999 of approved make for drainage system

pipe line, pipe shall be jointed with each other with

rubber lubricant, pipe shall be fixed on wall using of

PVC clamp of the size 160 mm diametre x 210 mm

length x 196 mm heigh at every 2000 mm center to

center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc.

including testing of pipes and joints and jointed with

adhesive solvent cement including cost of all

Providing, laying and jointing in true line and level

diametre U.P.V.C (Type B) conforming to IS

13592-1992 with one end plain and other end

socketed with rubber ring, & fittings conforming to ISI

14735-1999 of approved make for drainage system

pipe line, pipe shall be jointed with each other with

rubber lubricant, pipe shall be fixed on wall using of

PVC clamp of the size 110 mm diametre x 149 mm

length x 145 mm heigh at every 2000 mm center to

center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc.

including testing of pipes and joints and jointed with

adhesive solvent cement including cost of all

Providing and fixing PVC SWR Nahni trap IS

for drain - 100 mm diameter with jali of the following

84 nominal diameter of self cleansing design with C.I 15.00 Each 600.24

scread down or hinged grating including the cost of

cutting and making good the walls.

Providing erecting and fixing double coated ISI water

85 tank of required capacity each with all necessary 35000.00 Ltr 3.95

fitting and connection etc. complete on terrace

Providing and fixing ball cock of approved. quality as

directed.(A) Copper Metal (i) 25mm dia.

Providing and fixing ball cock of approved. quality as

directed.(A) Copper Metal (ii) 50mm dia.

Providing and fixing S.W. gully trap with C.I. grating

brick masonry chamber and water tight C.I. cover with

88 frame of 300mm x 300mm size (inside) with standard 12.00 Each 1292.20

weight.(i) Square mouth traps. (A) 100mm x 100mm

Providing laying (to level or slopes) and jointing

reinforced concrete Light duty non-pressure pipes I.S.

89 class NP2 of the following internal diameter with 35.00 Rmt 444.62

collars and butt ends prepared for collar joints

including testing of joints complete. (D) 300mm

Providing laying (to level or slopes) and jointing

reinforced concrete Light duty non-pressure pipes I.S.

90 class NP2 of the following internal diameter with 25.00 Rmt 805.45

collars and butt ends prepared for collar joints

including testing of joints complete. (E) 450mm

Constructing Manhole with R.C.C. top slab in 1:2:4

mix (1-cement :2-coarse sand : 4-graded stone

aggregate 20mm nominal size) foundation concrete

1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats

+ 50mm size) inside plastering 15mm thick with

Cement Mortar 1:3 (1-Cement : 3-coarse sand)

finished with a floating coat of neat cement and

making channels in cement concrete 1:2:4 mix

(1-Cement :2-Coarse sand :4-stone aggregate 20mm

91 nominal size) finished smooth complete including 4.00 Each 11029.97

curing and festing (i) Inside size 900mm x 1200mm

and 1.5M. deep including C.I. cover with frame size

560mm diameter total weight of cover and frame to be

not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of

frame 64 Kg.)(A) With 230mm thick walls of brick

msonry using brick having crushing strength not less

than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1-

Cement: 5-Coarse sand) (1) A type depth 0.90 Metre

for 150mm diameter sewer.

Constructing Manhole with R.C.C. top slab in 1:2:4

mix (1-cement :2-coarse sand : 4-graded stone

aggregate 20mm nominal size) foundation concrete

1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats

+ 50mm size) inside plastering 15mm thick with

Cement Mortar 1:3 (1-Cement : 3-coarse sand)

finished with a floating coat of neat cement and

making channels in cement concrete 1:2:4 mix

(1-Cement :2-Coarse sand :4-stone aggregate 20mm

92 nominal size) finished smooth complete including 5.00 Each 19349.64

curing and festing (i) Inside size 900mm x 1200mm

and 1.5M. deep including C.I. cover with frame size

560mm diameter total weight of cover and frame to be

not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of

frame 64 Kg.)(A) With 230mm thick walls of brick

msonry using brick having crushing strength not less

than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1-

Cement: 5-Coarse sand) (2) B type depth 1.50 Metre

for 150mm diameter sewer.

Constructing brick masonry chamber for underground

C.I. Inspection chamber and bends with bricks having

crushing strength not less than 35Kg/Cm2 in C.M. 1:5

C.I. cover with frame (Light duty) 455mm x 610mm

intenal dimensions total weight of cover with frame to

be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt.

of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix

(1-cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed

concrete etc. complete.(ii) Inside dimensions 500mm

x 700 mm and 450mm deep for pipe line with one or

Providing and laying (to level or slopes) and jointing

with stiff mixture of

94 Cement Mortar in proportion 1:1 Salt glazed 15.00 Rmt 211.58

stoneware pipes including

testing of pipes and joints complete.(A) 100mm dia.

Providing and laying (to level or slopes) and jointing

with stiff mixture of

95 Cement Mortar in proportion 1:1 Salt glazed 30.00 Rmt 305.14

stoneware pipes including

testing of pipes and joints complete.(B) 150mm dia.

Providing and laying Cement concrete 1:5:10

(1-Cement : 5-Fine sand :10- Graded stone aggregate

40mm nominal size) bedding for stoneware pipes of

following internal diameters with necessary formwork

and curing complete.(A) 100 mm dia. (112 mm

Ave.bed thickness)

Providing and laying Cement concrete 1:5:10

(1-Cement : 5-Fine sand :10- Graded stone aggregate

40mm nominal size) bedding for stoneware pipes of

following internal diameters with necessary formwork

and curing complete.(B) 150mm dia. (166mm Ave.

Supply, Installation, Testing and Commissioning of

Electric driven fire pump suitable for

automatic/manual operation and consisting of

following: complete in all respect as required.

(a) Monoblock pump to ensure a minimum pressure

of 3.5 kg / sq.cm. at highest and farthest outlet at

specified flow of 900 lpm at 65 m. head conforming to

Supplying, Installation, Testing and Commissioning of

Control Panel suitable for automatic/manual operation

of fire fighting pumps consisting

(a) Necessary cabling, wiring, earthing frompanel to

individual equipment shall be included in the quoted

(b) Facility for more selections i.e auto or manual.

(c) Protection failure and control cabling.

(d) interlocking of pressure switch with pumps

(e) soft starter

Supply, Installation, Testing and Commissioning of

150 mm dia Pressure Gauge of range 0-16 Kg/cm²

conforming to IS-3624 having bourdon tube of

stainless steel 310 in cast aluminium, stove

enameled, black, weather proof case with outer,

screwed aluminium bezel and complete with

necessary U-type stainless steel siphon tube and

cock including providing suitably painted angle iron

support to the tube etc. as per specification complete

Supply, Installation, Testing and Commissioning of the

following sizes of flange jointed / screwed / welded,

M.S Pipes of Class C (Hevy class) ISI marked

including accessories such as MS bracket, U clamps

with Anchor fasteners, tees / elbows / reducers /

101 couplings / unions / bends / flanges etc., and laying 45.00 Rmt 1674.89

on the surface including painting with one coats of

anticorrosive primer and one coats of approved red

enamel paint after laying and testing after Installation

etc. as per specifications complete as required.

(a) 100 mm dia.

Supply, Installation, Testing and Commissioning of the

following sizes of flange jointed / screwed / welded,

M.S Pipes of Class C (Hevy class) ISI marked

including accessories such as MS bracket, U clamps

with Anchor fasteners, tees / elbows / reducers /

102 couplings / unions / bends / flanges etc., and laying 6.00 Rmt 1152.21

on the surface including painting with one coats of

anticorrosive primer and one coats of approved red

enamel paint after laying and testing after Installation

etc. as per specifications complete as required.

Supply, Installation, Testing and Commissioning of the

following sizes of flange jointed / screwed / welded,

M.S Pipes of Class C (Hevy class) ISI marked

including accessories such as MS bracket, U clamps

with Anchor fasteners, tees / elbows / reducers /

103 couplings / unions / bends / flanges etc., and laying 2.00 Rmt 365.88

on the surface including painting with one coats of

anticorrosive primer and one coats of approved red

enamel paint after laying and testing after Installation

etc. as per specifications complete as required.

Supply, installation, testing and commissioningof C.I.

Butterfly valve (PN1.6) with flanges, nut bolts, gaskets

complete as required.

(a) 100 mm dia.

Supply, Installation, Testing and Commissioning of

105 NON RETURN VALVE. 1.00 Nos 6074.65

(a) 100 mm dia.

Supply, installation, testing and commissioning Single

Headed Fire Hydrant Valve with 80 mm N.B. flanged

inlet, 63 mm dia female instantaneous outlet type.

S.S.coupling, blankcap, chain, twist release type lug &

all accessories Conforming to IS:5290. Including

fixing with supports, flanged tapping from wet riser,

orifice plate complete as required by the Local Fire

Supply, Installation, Testing and Commissioning of

Weather proof Standard MS Fire Hose Cabinet wall

mounting type (450 mm x 600 mm x 250 mm deep)

having single opening with necessary locking

arrangement by allan key suitable for housing 1 no.

hosepipe, 1no. Branch pipe & nozzle spanner.

Supply, installation, testing and commissioning

non-percolating rubber reinforced lined fire Hose pipe

(as per IS:636) of 63 mm dia and 15 mtrs long. The

108 hose shall be rated for burst pressure of 35.7 1.00 Nos 5137.32

Kg/sqcm. Hose shall be complete with ISI marked SS

male & female coupling (IS:903) bound & riveted to

hose pipe with SS rivets & 1.5 mm SS wire.

Supply, Installation, Testing and commissioning of

mm dia instantaneous pattern Alluminium short

109 branch pipe, 20 mm dia nozzle conforming to IS:903, 1.00 Nos 1945.52

suitable for inter connection to hose pipe coupling

complete as required by the Local Fire Authority.

Supply, installation, testing and commissioning of First

Aid Hose Reel equipment conforming to IS:884

comprising of hose reel drum, 8 mm shut off nozzle,

110 Rubber hose reel tubing as per IS: 444 of 25 mm dia 1.00 Nos 7201.30

x 30 mtr. long, painting, Manual fix type with fixing

bracket, anchor fastener, bolts & nuts etc. complete

as required by Local Fire Authority

Supply, installation, testing and commissioning of SS

111 Ball Valve. 2.00 Nos 1800.33

Supply, installation, testing and commissioning of

Cast lron Two Way Fire Brigade Inlet as per IS:904

112 having 63 mm dia inlet with blank cap and chain with 1.00 Nos 7950.47

necessary fittings, flanges, nut bolts etc. complete as

Supply, Installation, Testing and Commissioning of

113 Gun Metal Air Release Valve with necessary fittings. 1.00 Nos 1562.22

Size: 25 mm (For Riser)

Supply, installation, testing and commissioning of

114 Pump on / off Remote switches to each internal 2.00 Nos 754.98

hydrant valve with required accessories.

Supply, installation, testing and commissioning of

XLPE insulated copper Cable from each Pump on/off

switches to Panel with all necessary accessories.

Size: 2 core 1.5 mm

Providing and fixing of Manual Fire Alarm system as

per requirement and specification consisting of

following items.

(a) Manual call point (FR-Polymer)

Providing and fixing of Manual Fire Alarm system as

per requirement and specification consisting of

following items.

(b) Hooters (FR-Polymer)

Providing and fixing of Manual Fire Alarm system as

per requirement and specification consisting of

118 following items. 55.00 Rmt 127.77

(c) Cable & other accessories: 3 C XLPE insulated

Providing and fixing of Manual Fire Alarm system as

per requirement and specification consisting of

following items.

(d) Manual Fire Alarm Panel

Supply, installation, testing and commissioning of

Carbon Dioxide (Co2) type Fire Extinguisher of 4.5 kg

120 confirm to IS:15683, with ISI marked / TAC approved 2.00 Nos 1986.17

fitted with required accessories including wall

suspension brackets.

Supply, installation, testing and commissioning of

ABC type 6 kg confirm to IS:15683, with ISI marked /

TAC approved fitted with required accessories

including wall suspension brackets.

122 Power Cablel (ALUMINIUM ARMOR) 42.00 Rmt 220.69

123 Consulting charges with documents work NOC fee 1.00 Nos 25250.00

1) All materials shall be ISI marked/ conforming to

relevant IS/ IEC standards and of approved make.

PVC pipes & accessories: Precision, BLP, Vraj or

equivalent approved.

Wires/ Cables (FRLS type): RR Kabel, KEI,

Cables (power/ control): HMT, Cable Corp,

Cablecel or equivalent.

Switchgears: Schneider, Siemens.

DB/ MCB/ RCCB: Schneider, Legrand, Hager.

Switches & accessories: Schneider, Legrand.

Light panels: Crompton, Philips.

Ceiling fans: Crompton, Usha, Havells.

Exhaust fans: Crompton, Usha, Havells.

Post-top lamps: Philips, K-Lite, Crompton.

LED flood lights: Crompton, Nissan.

Water cooler: Usha, Blue Star.

Pressure pump: Grundfos.

Cable lugs: Dowells, 3D.

2) All conduits shall be laid in proper alignment,

concealed/ surface as per Instructions, with

necessary saddles, junction boxes, bends, tees,

and inspection boxes.

3) Wiring shall be done with proper ferrules/

numbering and lugs. No loose joints/ taped

connections shall be permitted.

4) Switches, sockets, and accessories shall be

installed in flush metal boxes/ PVC boxes with

proper earthing.

5) Distribution boards shall be properly mounted,

dressed, and labelled.

6) Fans, lights, and fixtures shall be installed with

necessary supports and tested.

7) All wiring circuits shall be tested for continuity,

insulation resistance, and polarity before

8) Earthing shall be provided as per IS 3043 with

earth electrodes/ pits tested for resistance ≤

9) All equipment, DBs, panels, and circuits shall

be checked for phase sequence, load balancing,

and proper functioning.

10) Contractor shall provide test reports and

completion certificate before handing over.

11) Work shall be coordinated with other services

to avoid clashes.

12) All rates shall be inclusive of supply,

installation, testing, commissioning, scaffolding,

cutting/ chasing, and making good.

13) Entire work shall be executed as per relevant

IS standards, IE rules, and direction of

Engineer-in-Charge.

Constructing brick masonry chamber for underground

Inspection chamber and bends with bricks having

strength not less than 35Kg/Cm2 in C.M. 1:5 C.I.

frame (Light duty) 455mm x 610mm intenal

dimensions total

weight of cover with frame to be not less than 38Kg.

cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top

slabe with 1:2:4 mix (1-cement :2- coarse sand

:4-graded stone aggregate 20mm size) foundation

concrete 1:5:10 inside plaster 15mm thick with

cement mortar 1:3 finished smooth with a floating coat

of neat cement on walls and bed concrete etc.

complete.(i) Inside dimensions 455mmx 610mm and

450mm deep for single pipe line.

Providing and laying in trenches galvanised mild steel

tubes (Medium grade) of the following nominal bore,

tube fitting (Earthwork in trenches to be measured

for separately)(E) 65mm

Providing and laying in trenches galvanised mild steel

tubes (Medium grade) of the following nominal bore,

tube fitting (Earthwork in trenches to be measured

for separately)(D) 40mm

Providing and laying in trenches galvanised mild steel

tubes (Medium grade) of the following nominal bore,

tube fitting (Earthwork in trenches to be measured

for separately) (C) 25mm

Point wiring for Light / Bell with 2-1.5 sq.mm &

earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length , in below

type of pipe erected with 6A Modular type switch /

bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden

box, single mounting base frame covered with

128 textured/metallic/white front plate modules erected on 108.00 Pt. 493.89

/ in wall / ceiling as per pipe erected, with necessary

Lamp holder/ceiling rose / H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and

accessories erected flushed on wall/ceiling complete

Point wiring for FAN with 2-1.5 sq.mm & earth wire of

1.5 sq.mm (Green) both are of .ISI marked 1.1 KV

Grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected

with 6A Modular type switch and hum free EME step

type electronic fan regulator mounted and

accessories with earth continuity of following type

erected on PVC / Metallic/Wooden box, single

mounting base frame covered with

textured/metallic/white front plate modules erected on

/ in wall / ceiling as per pipe erected. with necessary

ceiling rose / H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and

accessories erected flushed on wall/ceiling complete

Point wiring for on board Looped Plug with 6A

Modular type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate

modules erected on / in wall / ceiling with following

type accessories

Point wiring for Individual Plug with & earth wire of

1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug

erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall /

ceiling as per pipe erected with following type of

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu.

Wire from nearby switchboard/mcb db board

(a) with medium class Rigid PVC pipe and

accessories erected flushed on wall/ceiling complete

Point wiring for Individual Plug with & earth wire of

1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug

erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall /

ceiling as per pipe erected with following type of

[III] For 16A Plug and 16 amp switch with 2-4 sq.mm

Cu. Wire with 2.5 sq.mm ( green) earthing wire from

(a) with medium class Rigid PVC pipe and

accessories erected flushed on wall/ceiling complete

Providing and erecting Mains with 1.1 KV grade FRLS

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected concealed

in /flushed on wall/ceiling, with 1.5 sq. mm copper

133 conductor FRLS PVC insulated stranded wire of 375.00 Mtr. 90.90

green colour for earth continuity of following size

(A) With medium class Rigid PVC pipe and

(b) 2 wire 2.5 sq. mm

providing and erecting Mains with 1.1 KV grade FRLS

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall

/ ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size

(A) with medium class Rigid PVC pipe and

(a) 2 wire 4 sq. mm

providing and erecting Mains with ISI marked, 1.5KV

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms

to IS 694, IEC - 227 erected in existing pipe of

135 following size (Specifically for control panel, relays, 50.00 Mtr. 40.40

power switchgears, motor starters & control wiring)

with required size of copper lugs, nuts and bolts if

(d) One wire 4.00 sq. mm

Providing and erecting Sheet Steel powder coated

MCB distribution board - flush / surface mounted fitted

with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used)

(B) three phase incoming and single phase horizontal

type outgoing Per phase isolation type (PPI)

(b) sheet steel double door

Providing and erecting Sheet Steel powder coated

MCB distribution board - flush / surface mounted fitted

with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used)

(B) three phase incoming and single phase horizontal

type outgoing Per phase isolation type (PPI)

(b) sheet steel double door

Providing and erecting Sheet Steel powder coated

MCB distribution board - flush / surface mounted fitted

with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used)

(A) single phase incoming and horizontal single phase

(b) sheet steel double door (IP-43)

Providing and erecting Sheet Steel powder coated

MCB distribution board - flush / surface mounted fitted

with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used)

(A) single phase incoming and horizontal single phase

(b) sheet steel double door (IP-43)

Supplying KITKAT pattern porcelain cut-out fuse with

base of following current capacity erected on existing

140 block board. 3.00 Ea. 494.90

Providing and erecting busbar chamber confirming to

IS-375 fabricated from 16 G.M.S. sheet, dust &

vermin proof having hinged door with rubber gasket

and necessary busbar supports with COPPER busbar

having current density not more than 1.6 Amp. /

sq.mm (Rated current / cross section area) duly

141 wrapped with colour insulation tape for phase 1.00 Mtr. 6761.95

sequence, three phase & neutral each suitable for

following current capacity with necessary painting

mounted on wall or pedestal frame of required size

with necessary connections.

(B) Suitable for 200 Amp. capacity

Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking

capacity ICU of 35 KA. at 415 V. having normal

current rating 125A. with Fixed thermal & magnetic

142 release suitable to work on A.C.supply 50 c/s. with all 1.00 Ea. 9504.10

internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking

capacity ICU of 25 KA. at 415 V,having normal current

rating up to 25 A to 100A. with Fixed thermal &

magnetic release suitable to work on A.C. supply

143 c/s. with all internal connections, spreader tinned 1.00 Ea. 7282.10

copper & complete erected in existing 16 G.M.S.

ICS=100% of ICU only Cat III

Providing and erecting Approved make RCCBs

conforming to IS: 12640 and having sensitivity of

mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on 3 phase and neutral

415V,50Hz. having characteristic of quick action &

144 tripping with all advance feature & do not incorporate 3.00 Ea. 3585.50

any electronic component for following Max. rating

erected as directed.

(iii) 63 Amps. FP

Providing & erecting 415V MCB Four Pole Switch for

Lighting Load (B curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box having

145 following capacity 3.00 Ea. 681.75

(a) 6 to 32 Amp.

Providing & erecting 415V MCB Four Pole Switch for

Lighting Load (B curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box having

146 following capacity 2.00 Ea. 681.75

(a) 6 to 32 Amp.

Providing & erecting 240 V MCB double pole switch

for lighting Load (B Curve) having 10 KA breaking

capacity & confirms to IS : 8828 in existing box having

147 following capacity 1.00 Ea. 328.25

(A) 6 to 32 Amp.

providing and erecting Miniature circuit breaker single

pole 6A to 25A suitable to operate on 240 V A.C.

system and having breaking capacity 10 KA to be

148 erected in existing box. confirming to IS 8828/1996 100.00 Ea. 131.30

"Supplying and erecting LED indoor fittings with LEDs

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder

coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with

company mark/name

160V to 270V,Power Factor more than 0.95, THD <

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges

(A) Square/ Circular shaped Surface/Recessed Mount

Downlight with provision for spring loaded mounting

clips complete.IP20

(v) 24 watts, 12" x 12" , Surge-2 KV

"Supplying and erecting LED indoor fittings with LEDs

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder

coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with

company mark/name

160V to 270V,Power Factor more than 0.95, THD <

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

150 LED driver efficiency > 85 % 48.00 Ea. 503.99

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges

(A) Square/ Circular shaped Surface/Recessed Mount

Downlight with provision for spring loaded mounting

clips complete.IP20

(ii) 11-15 watts, Surge-2 KV

Providing & erecting Approved make Ceiling Fan with

double ball bearing ISI mark with Condenser 230 volt

A.C.50 Hz 1200 mm sweep complete having

151 blades aluminium body and blade sets having 20.00 Ea. 2727.00

ornamental design shanks , canopy erected with

earthing. [ Make shall be approved by Engineer in

Providing & erecting fresh air fan 250 mm dia with

square frame make of ABS body with louvers

"Supplying and erecting LED indoor fittings with LEDs

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and

high U.V. & corrosion resistance with diffuser with

company mark/name 160V to 270V, Power Factor

more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

153 LED driver efficiency > 85 % 2.00 Ea. 439.35

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges

(A) Tube Light with integral driver

(iv) 22-24 Watts, Surge - 2KV,IP-20, conventional

Providing and erecting approved make split

air-conditioning unit consisting of copper condensing

unit with fan motor, hermetically sealed rotary

compressor with accessories etc. duly connected

separately erected evaporating unit and blower motor

with its accessories by means of extra supplied

154 proper insulated copper tubing,drain PVC pipes 12.00 Ea. 49540.50

suitable for ( cost includes powder coated Stand, Eco

Friendly green gas charging, 15A plug top & Remote

Control) with necessary core cutting.

(c) for 2 ton capacity

For 3 Star Rating of current year

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand Aluminium conductor for

1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables

(C) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core)

Providing and erecting XLPE (IS:7098)(I)-88 ISI

armoured cable multistrand Aluminium conductor for

1.1 KV. to be laid on wall with necessary clamps or in

156 existing trench / pipe of following size of cables 10.00 Mtr. 176.75

(A) 4 core 16 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand Copper conductor for

1.1 KV. to be laid on wall with necessary clamps or in

157 existing trench / pipe at road crossing or floor of 20.00 Mtr. 793.86

following size of cables.

(A) 4 core 10 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand / Solid Copper conductor

for 1.1 KV. to be laid on wall with necessary clamps

158 or in existing trench / pipe at road crossing or floor 50.00 Mtr. 597.92

of following size of cables.

(C) 4 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand / Solid Copper conductor

for 1.1 KV. to be laid on wall with necessary clamps

159 or in existing trench / pipe at road crossing or floor 175.00 Mtr. 426.22

of following size of cables.

(B) 4 core 4 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand / Solid Copper conductor

for 1.1 KV. to be laid on wall with necessary clamps

160 or in existing trench / pipe at road crossing or floor 375.00 Mtr. 317.14

of following size of cables.

(A) 4 core 2.5 Sq. mm

Supplying and erecting Flexible PVC insulated multi

strand multi core 1.1 kv grade ISI marked copper

wires of following size to be erected as directed.

(e) 1.50 Sq.mm 3 core round PVC sheathed

Solder less crimping type Aluminium lugs conforming

to IS suitable for cable of following size evenly

crimped with high pressure tool & connected to

162 switchgear terminals with brass/cadmium plated nut 12.00 Ea. 23.23

bolts in an approved manner.

Solder less crimping type Aluminium lugs conforming

to IS suitable for cable of following size evenly

crimped with high pressure tool & connected to

163 switchgear terminals with brass/cadmium plated nut 4.00 Ea. 17.17

bolts in an approved manner.

Solder less crimping type Aluminium lugs conforming

to IS suitable for cable of following size evenly

crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

Solder less crimping type Aluminium lugs conforming

to IS suitable for cable of following size evenly

crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

Solder less crimping type Copper lugs conforming to

IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

166 terminals with brass/cadmium plated nut bolts in an 8.00 Ea. 11.11

approved manner.

Solder less crimping type Copper lugs conforming to

IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an

approved manner.

Solder less crimping type Copper lugs conforming to

IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an

approved manner.

Supplying & erecting in earthpit of minimum bore dia.

225mm size approved make Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS

3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 80 mm having

80-200 Micron galvanising, Inner pipe dia of 40 mm

having 200-250 Micron galvanising, connection

terminal dia of 14 mm with constant ohmic value

surrounded by highly conductive compound with high

charge dissipation suitable for following type of

applications with chamber and heavy duty cover

(A)(approved make OEM has to submit test

certificate including value of earth resistance of

installation duly stamped and signed by agency and

169 officer Incharge has to ensure the value of earthing 3.00 Ea. 8370.88

resistane mentioned in test Certificate) & having back

filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as

per IEC 62561-2017, Voltage drop:- < 1 volt at no load

& dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable

to retain moisture for long time Necessary test report

must be submitted by Agency.

"[B] For Electrical installation up to 11 KV located

in other than normal soil i.e. Soft Rock, Marshy

-Length of Pipe : 2 mtr

-Back filling Compound :1 no. Bag of 25 Kg. "

Providing and erecting Annealed bare Copper wire

Providing & erecting water cooler having storage

capacity 150 Ltr. & cooling capacity 150 Ltr.per hour

@ an ambient temp of 45˚ C. The outlet temp. of the

water should drop by 15˚C within a hour, The water

cooler should be comprising of hermetically sealed

compressor, fan motor, condensing unit, water tank

surrounded by evaporating, coil, thermostats, relay

etc.complete with necessary inlet & outlet connection.

The body of water cooler will be made from Stainless

Supplying and erecting Fully Automatic hydro

pneumatic booster system with cast iron housing

Enclosure class IP44 minimum, with built in PTO

motor protection and stainless steel impeller pump,

pump model GRUNDFOS CMB 5-46 series or

equivalent with 24 Liter hydro pneumatic pressurized

tank capacity : 3.1 m3/hr,Rated head :25 mtr motor

172 rating : 1 H.P. includes pressure switches, Non Return 1.00 Ea. 35552.00

Valve, Pressure Gauge, 5 way Brass connector, with

necessary Plumbing work of 25mm dia suction and

delivery pipe which includes all required size of pipes

which includes all required size of pipes, Joints

valves, Bypass valve, labor all accessories required

for installation of pressure pump ( Foundation work

and base stand cost included)

S.I.T.C. of single phase submersible pump set

suitable for 100 mm size or more dia bore well having

motor capacity and discharge as under with

necessary panel box. Lifting and Lowering taken

(c) Motor rating 2 HP (17 stage) pump having

capacity of 106 LPM at 40 mtr head suitable for

mm dia. delivery pipe

Supplying and erecting Direct - On - Line Starter with

18 A. rating contactor and with 3.5 Amp. 18A range

directly operated in totally insulated elegant enclosure

for single phase operation up to 3 HP as per IS

174 complete erected on P.W. Block with necessary 1.00 Ea. 2477.53

Providing and, fixing heavy duty flange type brass

double compression type cable gland with rubber

ring for PVC insulated armoured cable complete with

out going tails, insulating tape etc for following size of

(A) 3 & 1/2 / 4 core 25 Sq. mm

Providing and, fixing heavy duty flange type brass

cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails,

176 insulating tape etc for following size of cables. 2.00 Ea. 54.54

(D) 2 to 4 core 16 Sq. mm

Providing and, fixing heavy duty flange type brass

cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails,

177 insulating tape etc for following size of cables. 4.00 Ea. 43.43

(B) 2 to 4 core 6 Sq. mm

Providing and, fixing heavy duty flange type brass

cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails,

178 insulating tape etc for following size of cables. 110.00 Ea. 37.37

(A) 2 to 4 core 2.5 / 4 Sq. mm

15A. 10 way bakelite connector duly erected on

existing board.

Providing & laying approved make Double walled

corrugated pipes (DWC) of polyethylene(conforming

to IS 14930 II )with necessary connecting

accessories of same material at required depth in

existing trench for laying of cable. below ground /

road surface for enclosing cable

(A)50 mm outer dia

Making trench in soft soil of suitable width of 90 cm

deep for laying cable or locating the fault all over the

run and back filling the same and making the surface

as normal ground.

Supplying & erecting Steel tubular pole (Swaged)

confirming to IS - 2713 (Part-II) 1980. Manufacturing

process of steel tubular pole should be as per IS

specification. Basic steel tube should be ISI Marked.

Pole should be painted by one coat of Zinc comet

Primer and two coat of Aluminium /approved paint to

be erected on / in existing Foundation. The length of

poles are as below.

(C) 9.0 mtr. Long Swaged Steel tubular pole

(i) Pole as per IS code 410-SP-25 with 300 X 300 X

mm base plate with necessary G.I. J Bolts

(Approximate weight 78 Kg) For burial erection

(ii) Add Extra for M.S. Base plate 300 X 300 X 16 mm

for pole, mounting on surface of foundation on GI

foundation bolt. with required stiffeners.

(iii) Add Extra for PU base primer and PU Paint on

Providing and erecting street light pole bracket

comprising main B Class MS pipe of 4.2 cm/require

outside dia. complete with suitable B Class M.S.

sleeve tubing of approx. 45cms.length and suitable for

76.5 mm / 80mm. / require size pole top having

sufficient fasteners for fixing the brackets and having

spread of 1 mtr. length with suitable rise as per site

condition & suitable welded stiffener reducer and

nipple with check nut complete painted with one coat

of Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of

[C] Three Arm Bracket 1 Mtr

Supplying & erecting Galvanized M.S pipe post “B”

class 88.9 mm O.D 4 mtr. Long duly painted with two

coats of aluminium paint complete with metallic base

plate of 300 mm x 300 mm x 4mm thick for using as a

compound light pole with approx. weight 32 Kg.

Supplying & erecting approved make SMC press

moulded composite FRP. loop-in, loop-out approx.

2mm thick box complete with Bakelite connector strip

5way(3P+N+E),DIN rail for mounting mob & hinged

doors as per requirement having locking

arrangements with mounting clamp with nuts, bolts &

washers suitable for erection on pole with cable

clamps& earth bolt of following size of box.

(E) 200mm x 140mm x 125mm [deep]

Providing and erecting Pipe type earthing having

cms.long and 2.5 cms. dia. galvanised iron pipe with

coupling and buch buried in specially prepared earth

pit complete with necessary 8 SWG earth wire.

"Providing 1:2:4 cement concrete foundation & 70 %

PCC from bottom including excavation for the pole of

size 60 x 60 x 150 cm. Deep in below ground level

187 with plinth of 45 cm x 45 cm(or 45 cm dia x 45 cm) 50.00 Ea. 1949.30

high upper ground level with necessary curing and

finishing in approved manner.

( for 9 & 10 mtr pole)"

For using salt and charcoal / coke as required for pipe

Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency

more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95,

THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio

>0.45, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-79 &

LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity

between the ranges shown.)

(C) Post Top Lantern LED fitting comprises of finish

cast aluminum spigot and spun aluminum canopy

fixed with opal polycarbonate, pipe arrangement for

vertical mounting driver and accessories wired upto

terminal block.IP

Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency

more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95,

THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio

>0.45, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-79 &

LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity

between the ranges shown.)

(B) Flood Light (IP-65), Surge protection -4KV

integral and ,Light must have 440VAC line supply with

over-voltage protection.

(v) above 120 to 160 watts

Supply, Installation, testing and commissioning

including vaccumiazation and Nitrogen testing of

following nominal sizes of soft/hard drawn copper

refrigerant piping for VRV system, complete with

fittings, with suitable adjustable ring type hanger

supports, jointing/brazing including accessories,

insulated with XPLE Class-0 tubular insulation/with

191 Class-0 closed cell elastometric nitrile rubber tubular 120.00 Mtr. 515.10

sleeves sections of specified thickness as given

below for Suction and Liquid lines, all accessories as

per specifications etc with necessary refrigerant joint

(C.) 12.7 mm dia (OD) (Soft drawn) with tube

thickness 1.2 mm with 19 mm thick insulation

Supplying and erecting approved make water filter

having outer body of tough polycarbonate with fitter

cartridge having filter to trap micro elements with

coupling suitable for erection on pipe line.

Providing & laying approved make ISI marked Rigid

PVC pipe having 6Kg / cm2 (Class-3) to be erected at

road crossing on or floor as directed for laying of

193 cable. The pipes as following size of dia & weight per 50.00 Mtr. 146.45

(D) 75 mm inner Dia. (5.5 Kg/6RMT)

Supplying & erecting approved make LAN cable of

following size in existing pipe as per direction

Providing and erecting ISI mark Medium class RIGID

PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC

fittings & Junction boxes fixed with adhesive solution

& Clamps with following dia of pipes, in approved

manner as directed

196 provideing & fixing 16 CH N.V.R 1.00 Ea. 16160.00

197 provideing & fixing 2 Mp camera 12.00 Ea. 3232.00

198 provideing & fixing Pob switch 2.00 Ea. 4545.00

PGVCL lisening work for getting 3 phase power

199 connection including payment of fq and all other 1.00 Ea. 40400.00

charges on behalf of commissioner BMC.

Total Amount Without GST

Total Amount Without GST