SPECIAL REPAIRS TO BLDG NO P-191/ 1 TO 8 OF 811 ENGR REGT ONGC TA AT LANCER LINE UNDER GE (A) VADODARA.

Amount

Taking down cement or cement lime plaster, on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc

M&L for Rendering in two layer on fair faces of brick work or concrete sur-faces of wall 5 mm thick in CM 1:4 mixed with WPC @ 3% by wt of cement finished even and smooth without using extra cement over 10 mm thick rendering in cement mortar 1:6 (WPC will be measured and paid separately).

Supply only integral water proofing compound

M & L for preparation of new plastered surface of walls,and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M & L for complete removal of existing treatement of walls by dust proof wall sanding machine/building walls grinding cleaning machine and applying two coat of cement base paint over a coat of alkali resistant primer including preparation complete .

M&L for rendering 10mm thick on other than fair faces of brick work or concrete surfaces with CM 1:6 finished even and smooth withot using extra cement.

M&L for Preparing new plastered surface of wall and applying a layer 2 mm thick wall care puty and two coat of oil emulsion distemper over a coat of alkali resistant primer complete all as specified.

M & L for complete removal of existing treatement of walls by dust proof wall sanding machine/building walls grinding cleaning machine and applying a layer of 2 mm wall care putty and two coat of oil emulsion distemper over a coat of alkali resistant primer complete .

M&L rendering 5mm thick on concrete surfaces of ceiling with CM 1:3 finished even and smooth withot using extra cement.

M&L for Preparing new plastered surface of ceiling and apply three coats of white wash complete all as specified.

M & L for complete removal of existing treatement of ceiling by dust proof ceiling sanding machine/building ceiling grinding cleaning machine and applying two coat of white wash complete all as specified and directed.

Taking down chowkhats or frames exc 1.5 sqm but n exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

S&F pressed steel frames 125 x 60mm for doors with one or more rebates including necessaey fixing lugs, hinges, lock strike plate, etc., complete, as specified and dircted.

S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all a s spcified and dircted.

S&F 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. Fitted with cut and mitred breads for securing glass, etc: sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24 (a); supplied and fitted to chowkats.

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised staples or wooden beading complete all as specified and directed.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern springs including roller plate complete all as specified and directed.

M&L for preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed

Taking down chowkhats or frames n exc 1.5 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

S & F powder coated aluminium frame (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

M & L for 5.5mm thick sheet glass, ordinary quality and glazing with rubber beading or with glazing clips, all as specified and directed.

S&F 300mm aluminum anodised sliding door bolts, with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast alluminium alloy complete all as specified and directed.

S&F 150 mm aluminium anodised barrel tower bolts, of extruded section all as specified and directed

S&F mild steel butt hinges of 100 mm size medium weight cold rolled by welding to frame complete all as specified and directed

S&F 150 mm extruded aluminum alloy handles, fabricated type anodized complete all as specified and directed

S&F in repair 20 mm dia D type aluminium anodised towel rail 600 mm long between flanges complete all as specified and directed.

S&F in repairs 20 mm dia anodised aluminium tubular curtains rod complete all as specified and directed.

S&F in repair aluminium anodised brackets for curtain rod complete all as specified and directed .

S&F in repair floor door stopper of aluminium alloy body and tongue, overall length of cover plate 140 mm anodised with hard drawn steel spring, fixed in floors complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L for joint free non skid ceramic coloured tiles 7 to 8mm thick, area of each tiles exceeding 0.11sqm and n. exc 0.18 sqm in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15mm thick in cement mortor (1:6) complete.

M & L for glazed ceramic coloured wall tiles in vertical surface 350x250x 7mm/ 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over including 10mm thick rending in CM : 1:4 complete all as specified and directed.

M&L for Hot Bitumen 1.2kg/sqm for waterproof and damp-proof treatments any grade all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store of 15mm bore size complete all as specified and directed.

ditto as per item no 33 above but 25mm bore complete all as specified and directed.

Supplying and laying of UPVC SCH-40 pipes of 15mm bore with fittings complete all as specified.

M&L for GI tube medium grade with fittings and fixed complete to walls or laid in floors,bore of pipe 25 mm all as specified

Demolition of Brickwork or stone/boulder masonary built in cement or cement lime mortar including all quoins, arches,pillars etc. complete all as specified and directed.

M & L for Brickwork with subclass 'B' old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for Hardcore of gauge n exc.63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to true surfaces , in plinth protection complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40mm graded aggregate) and finishing cement concrete surface even and smooth without using extra cement as in plinth protection complete all as specified and directed.

M&L for 50 mm avg thick PCC padding in cement concrete type B0 (1:2:4) using 12.5 mm graded stone aggr mixed with WPC @ 2% by wt of cement , laid on roof all as specified and directed. (WPC will be measured and paid separately).

M&L for Rendering 10mm thick on flat concrete roof surfaces in CM 1:4 mixed with WPC @ 3% by wt of cement, finished even and smooth without using extra cement complete all as specified and directed. (Note:-WPC will be measured and paid separately).

M & L for brushing with neat cement slurry @ 3Kg/Sqm

M&L for water Proofing treatment to roof slabs by applying one coat of bituminious/polymerized primer confirming to IS-3384 @ 0.30 Ltrs/Sqm, and laying actetic polypropylene (APP) modified membrane pre fabricated , reinforced with non woven polyester, of minium 3.5 Kg/Sqm 3 mm thick (minium) with minium 75 mm side overlaps and minium 100 mm end overlaps and applying one coat of aluminium paint @ 0.11 Kg/Sqm over APP membrane complete all as specified and directed by Engr-In-Charge

M&L for complete removal of loose/ cracked concrete including reinforcement if required from RCC roof projection, chajja, fins, facia etc and making good with PCC (1:1.5:3) type A0 using 12.5 mm graded aggregate) in any slab and in any position finsihed the surface even and smooth with out using extra cement including necesary formwork and welding / binding of reinforcement ( including new reinforcement) if required complete making good to match with existing surfaces complete.

Disconnecting existing tanks, setting aside for lowering if required carrying out petty repairs, cleaning etc hoisting and refixing in position of capacity exc 250 ltr but n exc 500 ltr complete all as specified and directed.

Supply hoisting and fix 500 ltrs rotational moulded polythene water storage water tanks twin layered construction ISI Marked, ( cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I incl 20mm GI light grade over flow pipe approx length 1.5m long, 20mm GI medium grade pipe for wash out approx length 2.00 m duly plugged at one end including dismantling existing tank complete all as specified.

S&F in repair 25 mm bore ball valves, high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210gms) complete all as specified and directed.

S&F in repair glass shelf with chromium plated guard bar complete all as specified and directed.

S&F in repair vitreous china Wash hand basin, white , flat back size 450x300 mm except taps but incl brackets and 32 mm dia CP waste coupling all as specified.

S&F in repair CP Grating of size 150x150 mm complete all as specified and directed.

S&F in repair 15 mm dia 450 mm long PVC connection pipe with two PVC PTMT nuts at each ends with rubber washer complete all as specified and directed.

S&F in repair PVC connection pipe 15mm dia and 600 mm long with two PTMT nuts at each ends with rubber washer etc complete

S&F in repair15mm dia stop cock, fancy type cromimum plated complete all as specifed and directed.

S&F in repair 125mm dia Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union

Dismantling of 100mm cast iron or reinforced concrete drain pipes laid in trenches or fixed to wall or ceiling complete all as specified and directed.

Dismantling of 75mm cast iron or reinforced concrete drain pipes laid in trenches or fixed to wall or ceiling complete all as specified and directed.

S&F110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls as in waste/soil pipes complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls as in waste/soil pipe complete all as specified and directed.

S&F in repairs 110mm radius PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repairs 75mm radius PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repairs 75mm radius PVC (SWR) bends complete all as specified and directed.

S&F in repairs 110mm PVC (SWR) branch piece, single (Single Y) equal or unequal with access door complete all as specified and directed.

S&F in repairs 75mm PVC (SWR) branch piece, single (Single Y) equal or unequal with access door complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orissa pattern of size 580x440mm white, with integral foot rests (excluding flushing cistern and flush pipe) but including lime concrete bedding complete all as specified and directed.

S & F in repair vitreous china wash down water closet pan (pedestal pattern) white, including connection to drain or outgoing pipe and to flushing pipe, anti syphonage pipe etc complete with plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified .

S&F in repairs 110mm PVC (SWR) 'P' trap complete all as specified and directed.

S&F in repairs 110mm PVC (SWR) 'S' trap complete all as specified and directed.

S&F in repairs 75mm PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repairs 125/110mm PVC (SWR) gully trap setting and jointing with solvent cement complete all as specified and directed.

S&F in repairs 10 Litres, PVC valveless syphonic action type, flushing Cistern, low level, white inlet, ball valve, float, and brackets inclluding 32mm PVC flush pipe suitable for flushing cistern complete.

S&F in repair CP soap dish fixed to wall with brass chromium plated screws complete all as specified and directed.

S&F in repair Chromium plated long body fancy type bib taps with wall flange, cast copper alloy with round operating knob screwed down high pressure, screwed for 15mm bore iron pipe complete all as specified and directed.

S&F in repair 15mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs brass CP wall mixer for mixing hot & cold water screwed down for iron pipe 15mm bore and fixed complete.

S&F stainless steel kitchen plate rack made of 0.63 mm thick stainless steel sheet of size 750 mm x 750 mm x 250 mm fixed to wall with screws complete all as specified and directed.

M&L for 18-20mm thick green marble in one piece machine cut as in kitchen platform and like, set in cement mortor (1:4) and jointed in grey cement slurry and pointed in coloured cement (1:2) using marble dust with admixture of pigment to make door frame with marble shade, laid over and including 10mm thick back coat in cement mortor 1:4 complete all as specified.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheets, reinforced with MS square tube, supplying and fixing in opening as per specification and drawiing. The door frame shall be fixed to the wall using 75/100mm long MS screws complete.

Factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat rounded plain colour PVC :C: channel having a PVC sheet strip & 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert to top rail & bottom rail. Paneling of plain colour sheet to be fitted in the MS frame welded/sealed to athe satiles & rails with suitbale PVC sheet beadding and jointed together with solvent cement, supplying and fixing in the frame at site as per specification and drawings.

Providing and fixing factory made 18(+0.7mm) thick PVC sheet one sided pre laminated sheet cabinet shutter. 18 mm(+0.7mm) thk sheet shutter of density 600 kg/m3 bent at 90 degrees and finished all edges at all level for making edges, Lipping/bending or 0.5 mm thk PVC sheet lipping at all four edges using bonding tape etc complete all as per directions of engineer in Charge & Manufacturers's speciifcations.

Taking down carefully copper / Aluminium point wiring including (light, fan, socket or power and complete fittings, such as switches, ceiling roses, pendant holders, Batten holders, shades conical fan regulators, light or power sockets etc) removing materials from site and making good disturbed surfaces of walls roofs etc all as directed.

Taking down carefully UNSV main switch and DB's including MCBs of any size make, type and capacity and depositing at site as directed.

M&L for concealed point wiring complete with 1.5 Sqmm single core multistranded copper conductor PVC insulated and unsheathed FRLS cable 1100 volts grade, conforming IS 694 & color code in conduit system of wiring, drawn in including medium grade PCV conduit not less than 20 mm dia concealed, including cutting chases, finising of slote by means of cement mortor making good to the existing surface of the wall & touching with the existing colour of wall with three coats and making good disturbed surface complete, sunk in pressed steel terminal boxes of required size not less than 3.0mm thick factory made and factory painted with top cover 3.0 mm thick plastic laminated sheet6 fixed with brass screw and washer with all accessories including single core solid conductor copper 1.5 sqmm size solid PVC insulated unsheathed cable as earth wire to common earth and connected to earth dolly drawn in same conduit complete all as specified.

One light/fan/bell point controlled by one switch 6 Amp one way

One 3 pin switch socket combination 6 amp on the independent board.

One 3 pin socket outlet on same board with other switches.

One light point controlled by two way switches

All as described as per item No 87 above but point wiring with 2.5 sqmm single core multi stranded copper conductor PVC insulated & unsheathed FRLS cable 1100 volt grade and 2.5 sqmm PVC insulated and unsheathed FRLS cable 1100 volt grade with multi stranded copper conductor for earth wire for 15/16 amp multi purpose socket combination point on independent board.

S & F switch piano flush type single pole, one way 6amp,

S & F switch piano flush type single pole, TWO way 6amp,

S & F switch socket combination 5 pin 6 amp,

S & F Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal.

S & F fan regulator electronic type 100Watt 20V-50Hz as directed by Engr-incharge,

S & F in repair ceiling rose surface bakelite 65 x 50 mm three terminal 230 volts ISI marked.

S&F Buzzer Ding Dong AC 230 V

S & F in repair 7W LED Bulb suitable for B22 holder . System Efficacy should be > 85 lm/ W. PF > 0.9, The Lamp Should have Cool Daylight Color temp of 6500K, lumen output >600 lm.

Taking down U/S FTL and Supply and fixing of 4' 18W LED Tube With Batten with system lumen output of 1800 lumens. System Efficacy should be > 115lm/ W. The Luminaire Should have Cool Daylight Color temp of 6500K & CRI>80.Life 40K burning hrs with 70% lumen maintenace. PF>0.95 Surge Protecton of 3KV.All the Photometrical & Electrical parametrs must be supported by LM79-08 test report from NABL Accridiated LAB OR UL, R9 Value > 0. Lamp starting time is not more than 1 Sec. The LED tube light conforms to applicable IS.Make of LED From Philips/Crompton/ Wipro. Housing of Batten should be made from Single piece powder coated CRCA sheet steel.Similar to Crompton LDSL 18-CDL with Master TLED 18W 1800 Lumens.

S & F in repair MCB DB factory made IP 42 protection class metal double door with 200 Amp rating bus bar 240/430V for fixing of MCBs/Isolators/RCCBs etc completed as under:-

SPN 12 way

SPN 8 way

S & F MCB SPN 32 Amps 10 KA rupturing capacity.

S&F MCB SP 5 to 30 Amp 240 Volts

M & L for sub main wiring concealed conduit using two single core 6 Sqmm fire retardant PVC insulated and unsheathed cable with copper conductor 1100 volts grade ISI marked drawn in and including rigid non metallic PVC conduit of suitable size and accessories like bends, tee, etc and cutting chasesas required ,fix on wall and ceiling and connecting to earth dolly and including 6 Sqmm earth wire, PVC insulated & unsheathed all as directed. NOTE : Two runs of single core 6.0 sqmm and one run of 6.0 sqmm copper FRLS cable as earth continuity conductor and suitable size conduit with accessories shall be measured as one length.

S & F wall security light LED type complete including GI bend 1.2 mtr and fixing on wall/pole with clamp, nut & bolt complete all as directed and specified by Engr-In-Charge. CAT Part No.LSTO-25-CDL 25watt of Make CG or its equivalent in Phillips/Wipro.

M&L for KAPITRODE Earthing with Cast Iron pipe electrode, 75mm bore, 3.15mm wall thickness , 2.9 metres length,with GI pipe & funnel, buried directly and preferably vertically in ground with top edge not less than 2.9 metres below ground level connected with earthing lead of 25x5mm dia galvanised iron strip including the following, : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1 of size 450x450x450mm with Cast iron cover with suitable handle. (c) 40 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead. (d) Requisite quantity of BFC Compound (bentonide powder) and black cotton soil. (e) Testing of earthing. NOTE :- On testing after completion of earthing, if the desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk and cost..

S&F of Exhaust fan 250 mm sweep 1250 RPM with minimum airflow/air delivery 720 Cmh, 06blades, light weight, rust proof body & blades, self opening louvers for protection from birds & rain water, IP-55, 230 Volt AC supply, rated power input not more that 45watt, connecting up including provison of cable from ceiling rose to fan.

S & F ceiling fan complete with blades, down rod from existing roof / truss or false ceiling, electronic regulator and accessories, 230V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor including ceiling fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and taking down existing UNSV ceiling fan complete all as specified and directed. Note : Old ceiling fans shall be deposited to AGE E/M store yard

Supply and fix electric water heater, vertical type, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe etc. complete all as specified and directed. Note : 1) Old electric water heater shall be deposited to AGE E/M store yard

P K SHETH

Aditya Construction

shree nathji trading corporation

Dagli Engineers

M/s. RAMESH NARHARI VALEKAR