SPECIAL REPAIRS OF PERIMETER WALL AT COD DEHU ROAD AND SPL REPAIR AT LINE BLDG NO T-66 AND T-67 (NISSAN HUTS) OF 147 LT AD REGT (COMP) UNDER AGE B/R (WEST) GE DEHU ROAD

Amount

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings all as specified and directed.

Dismantling of wrought iron or mild steel work any description and fixed in any position complete all as specified and directed.

M&L rolled sections as in main and cross beams, hip rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410 W (gde E 250 ) quality A including a shop coat of zink chromate primer complete all as specified and as directed.

S & F 0.5 mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screw all as per manufactures instructions fixed on roof with all fittings and accessories complete all as specified and as directed.

Ditto as per item No- 04 above but as in ridge, valley gutters etc complete all as specified and directed.

M & L for MS work as in wind tie for roof or any other work including securing bolts, all necessary drilling, bolting or riveting etc complete all as specified and directed.

Dismantling wall & ceilling boards(fibre pulp insulation etc) or insulation boards/ slabs/blankets, any thickness including cover fillets complete all as specified and as directed.

S & F 12mm thick Gypsum board for ceiling, insulation and accoustic purpose 60x60cm in size fixed with screws with staples incl anodised aluminium snap grid frame work 605x605 mm in flat/sloping ceiling with aluminium anodised grid work 35.60x23.60x1.60mm main Tee 23.60x23.60x1.60mm cross section and 26x26x1.60mm angle including 3mm dia GI wire suspender of suitable length aluminium cleats etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the permises complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick (square/rectangular) polished area of each tile exceeding 0.36 sqm but n exc 0.42 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles over 15 mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes complete all as specified and directed.

Ditto as per item No 10 above but in skirting over 10 mm thick screed bed or bedding layer in CM 1:4 for laying floor finishes complete all as specified and directed.

Demolition of brick work or stone boulders masonary built in cement mortar including all quoins, arches, pillars,etc for ashlar facings, dressed stonework, precast concrete articles and precast concrete block walling complete all as speicified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc. 6m mean radius built in CM 1:6 complete all as specified and directed by Engr-in Charge.

Taking down cement plaster of any description of brick or stone wall etc incl racking out joints and hacking for key, scrubbing down with water etc complete

M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick walls finished even and smooth w/o using extra cement and all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick work or conrete surfaces finishing the suface sand faced complete all as specified and directed.

M&L for preparation of new plastered surfaces & applying two coats of oil bound distemper complete over a coat of primer on wall surface complete all as specified and directed.

M&L for preparing new plastered surfaces & applying two coats of cement base paint over a coat of primer on wall surface complete all as specified and directed.

Taking down chowkhats or frame with shutter (w/o taking off shutter from the frame) of area n.exc 1.5 sqm each (incl old windows)

S&F for pressed steel frames for doors with one or more rebates incl necessary fixing lugs, hinges, lock strike plates of size 125 X 60mm complete and all as specified and directed.

M&L for cement concrete (1:2:4) type B0 (using 12.5 mm graded stone agg) as in back filling door frames complete and all as specified and directed.

S&F 30 mm thick flush shutter solid core construction with block board core & plywood face pannels commercial type on both sides complete and all as specified and directed.

S & F 35mm thick factory made glazed & skeleton shutter of 2nd class hard wood open rebated and prepared to receive gauge (divided into squares with sash bars) edges of framing plain chamfered or rounded, fitted without & fitted beads for securing glass etc, sizes of members of shutters as specified in SSR Pt-I Sec-8 clause 8.23 (a) and fitted to chowkhats complete all as specified.

M & L for preparation of new wooden surfaces exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F aluminium powder coated window sliding type (3 track) with frame size100x35x1.2mm and shutter 39.40x17.70x1.2mm with two glass shutter & one mesh shutter incl necessary jointing cleats glazing clips, rubber packing,and locking arrangement powder coated aluminium snap beading screws including 4mm plain float glass & 0.36 mm dia and 1.4 mm width of aperture stainless steel wire mesh, fittings etc complete all as specified.

S&F aluminium powder coated DECOGRILLE 7.5mm width and 6mm thick of design DG-102 having wt 3.131 kg/sqm fixed to and including powder coated aluminium U type frame with CP brass/Stainless steel screws @ 200c/c, including cutting the grill to proper opening size for fixing & operation of handles and fixing powder coated aluminium section around the opening all as per requirement and direction of Engr-in-charge.

S & F of 200 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S & F of 150 mm long extruded anodised aluminium alloy handle, fabricated type complete all as specified and directed.

S&F 100 mm Stainless steel Butt hinges,medium weight cold rooled fixed with screw or welding complete all as specified and directed.

S & F of 250 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F 20 mm dia stainless steel medium grade curtian rod fixing in any opening including stainless steel brackets 02 Nos bracket in each door/windows with side knob as specified and directed complete .

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m depth for foundation , etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out Hard / dense soil all as specified and as directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M&L cement concrete in surface channels and drains in cement concrete 1:3:6 C-2 using 40 mm graded stone aggregate complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms moulds mitred/stopped ends etc complete all as specified and directed.

M&L for cement concrete 1:3:6 type C1 (using 20 mm graded stone aggregate) as in copings, kneelers, apex, stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating complete all as specified and as directed by Engineer-in-Charge

Demolition of reinforced cement concrete in ground floor n.exc 15cm thick complete all as specified and directed.

M&L reinforced cement concrete type B1 1:2:4 (20mm graded stone aggregate) as in slab supported on walls,beams and columns in floors,roof landings,balconies, canopies deck slab and in shelves and the like complete all as specified and directed.

M&L formwork for rough finished surface to soffits of suspended slabs such as roof slabs,floor slabs,landings and similar works not exceeding 200mm thick of slab complete all as specified and directed.

M&L for mild steel TMT bars 6 to 8 mm dia cut to length, bent to shape required incl cranking, bending, hooking ends & binding with & incl mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed by Engineer-in-Charge.

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required incl cranking, bending, hooking ends & binding with & incl mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete ( unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M & L for 75 mm thick PCC type D-2 1:4:8 (40 mm graded aggregate) as in sub base for tiling complete all as specified and as directed

M & L for precast concrete interlocking paver block rubber moulded any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement and pigment including 25 mm thick sand cushion complete all as specified and as directed.

M & L for cement concrete Type C2 1:3:6 (using 40mm graded aggregates) as in plinth protection 75 mm thick finished top surface even and smooth without using extra cement complete all as specified and as directed.

Boring 300 mm dia holes 4 m deep in soil for under-reamed piles and getting out and disposal of spoil to a distance of n exc. 50 m

M & L for PCC 1:4:8 type D2 (using 40mm graded aggregates) as in Foundation filling and mass concrete all as specified and directed and as shown on drawing.

M & L RCC M 25 Design Mix (Using 20 mm Graded Stone aggregate) in Foundations, including rafts, footings, foundation beams; plinth beam, bases for columns,bands etc. under-reamed piles etc all as specified and directed and as shown on drawing.

M & L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams,bands and similar work; vertical or to batter for rough finished of surface of concrete flat all as specified and directed.

M & L RCC M 25 Design Mix (Using 20 mm Graded Stone aggregate) in Columns, pillars, piers, posts and struts all as specified and directed and as shown on drawing.

M & L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished of surface of concrete flat all as specified and directed.

M & L for PCC type B1(1:2:4, using 20mm graded stone aggregate) as in bed blocks/coping/ edging including use & waste of formwork for fair finished surfaces complete all as specified and directed.

Material and labour for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width Type C1 1:3:6 (20 mm graded aggregate ) and setting in mortar CM 1:6, complete.

S & F angle 75x75x6 mm independently with web and flange cut to shape drilled and countersunk for screws including bending and welding angles without connecting plate as bracket in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified and directed.

Restraining & Reseucring including making good staples of Galvanised. 4 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc all as specified and as directed by Engr-in-Charge. (each line wire to be measured).

S & F in Galvanised. 4 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc all as specified and as directed by Engr-in-Charge. (each line wire to be measured).

Returning filling in including spreading, levelling , watering and well ramming n exc. 25 cm in layers (Soil)

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m depth for foundation , etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose soil all as specified and as directed.

Providing and fixing concertina coil fencing with punched tape concertina coil 610 mm dia having 50 turns and stretches to cover 5-7m length and approx weight 8.75kg + 5% and fixed in existing angle iron Y shape including necessary clips or wires tied to GI barbed wire all complete as per direction Engineer in charge

S and F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M & L for Removing building materials from MoD land etc. (other than spoil payable under items 03028 to 03031 in Section-3—Earthwork) to a distance of exc 1km but n.exc 5km, beyond the lead included in the rates, including loading, unloading and stacking at the destination all as specified and as directed by Engr-in-charge

Taking down old point wiring and M&L for point wiring with 1.5Sqmm multistranded copper conductor cable of PVC insulated and unsheathed type alongwith 1.5 Sqmm PVC insulated unsheathed single stranded copper conductor cable for continuous earting in and incl casing/caping or PVC pipes and accessories having ISI marked surface type to be fixed with proper screws/(MS Steel strips if required) including hard PVC boards of suitable sizes and making arrangement for fixing switches, sockets, switch socket combination, fan regulatore etc for Note : Screws used for fixing PVC boards, casing and caping ceiling rose square blocks etc should be nickel cadmium screws:-

One light point controlled by one switch

One fan point controlled by one switch and regulators

One socket 5 pin 5 Amps flush type on independent board

One socket 5 pin 5 Amps flush type on same board

M&L for submain wiring with 2 single core PVC insulated multistranded flexible copper conductor 1100Volts grade (FRLS) cables 4.sqmm and 1 run 2.5 Sq mm PVC insulated multistrand copper conductor cable (FRLS) of green colour for continious earthing drawn through PVC surface/concealed PVC conduit of suitable size and with all accessories all as directed and specified by Engr-In-charge.( Note: Two runs of 4 sqmm, one run of 2.5 sqmm copper conductor and one run of surface/concealed PVC conduit of suitable size and with all necessary fixing accessories and making good disturbed surface area shall be measured as one length.)

S & F Switch piano flush type single pole one way 230V 6Amps

S & F Socket outlet 2 in 1 , 3 pin 5 Amps flush type 230V S.P. multipurpose type

S& lamp holder PVC/Polycarbonate type with back plate suitable for battern fittings

S & F ceiling rose surface PVC 50 mm dia three terminals including PVC mounting block, white/lvoury /Urea finish.

M&L in repair for stepped type electronic fan regulator flush type on the existin phenolic laminated sheet etc as required for ceiling fan 230 volt AC supply, 50HZ 1200/1400 mm sweep

M & L MCB DB SPN sheet metal double door enclosure mounted on teak wood board of suitable size for mounting MCB 230 Volts with 200 Amps rated bus bar 8 way

S & F MCB SP 5-32 amps, 240Volts 10KA

S & F MCB SPN 5-40 amps, 240Volts 10KA

Supply & fix LED tube light along with fixture, 20 W

Supply & fix LED lamp fittings along with fixture, 9 W

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete

Supply and fix ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor.

M & L for earthing complete with galvanised steel earth plate electrode 60cm ×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel,earth wire protected by GI pipe 15 mm dia 'light grade' including charcoal dust, common salt, excavation & earth work, PCC Pit with 1:3:6 type C-1, 40 mm thick RCC cover in 1:2:4 type B-1 reinforced with 8 mm dia TMT bars @ 75 mm c/c both ways with MS handles 12 mm dia, PGI funnel & GI watering pipe 'light grade' 20 mm bore all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion

Supply and lay pipe galvanised medium class including fitting complete 40 mm dia

Supply and lay pipe galvanised medium class including fitting complete 25 mm dia

Supply and lay pipe galvanised medium class including fitting complete 20 mm dia

Supply and lay pipe galvanised medium class including fitting complete 80 mm dia

M & L for High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 size of 40mm dia

M & L for road cutting and mading good with PCC 1: 3:6 type C-2 (using 40 mm graded stone aggregate) complete all as directed by Engr-in-Charge

Supply, laying, jointing, testing and commisioning XLPE cable 1100 Volts grade PVC insulated armoured and PVC sheathed with stranded aluminium conductor heavy duty ISI marked incl cable glands lugs bolts nuts washers etc to suit the cable size to be laid in trenches fixed along pole, LT panel floor bore or through GI pipe laid under floors, fixed, concealed in wall encased in GI pipe etc complete of 16 sqmm x 2 core incl taking down old unserviceable over head conductors and insulators channels carefully as directed by Engr-in-Charge:-

KARPE AND SONS CONSTRUCTION

S.R.M.K Enterprises

S Y Itkar Construction and Company