Construction of Sewer network under TP Schemes Nos. 412A, 412B, 243, 109, 413 & 411 and construction of 3 Nos.Pumping Stations (MPS 01- 11.98 MLD, MPS-2 12.24 MLD, MPS-3 20.55 MLD & SPS-12.5 MLD) and Sewerage Treatment Plant of 30 MLD Capacity within AUDA TP Scheme areas. (Job-40/2025-26)

Bill of Quantities

Depth of excavation for inlet units

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Excavation for well including removing and spreading

the excavated stuffs directed with all lead.

1.A) In all sorts of soils & Soft Murrum

(100% in all sorts of soils & Soft Murrum)

(100% in all sorts of soils & Soft Murrum)

(100% in all sorts of soils & Soft Murrum)

(100% in all sorts of soils & Soft Murrum)

(100% in all sorts of soils & Soft Murrum)

(100% in all sorts of soils & Soft Murrum)

1.B) In Hard Murrum

(100% in Hard Murrum)

(100% in Hard Murrum)

Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and disposing

off the excavated stuff upto 50 Meter lead.(A) Loose or

b) Dense or Hard soil 245.58 149.67 cmt

(C) Hard Murrum 18.58 256.12 cmt

(D) Soft rock not requiring Blasting 11.15 263.08 cmt

E) Hard Rock 7.43 597.60 cmt

Excavation for foundation 1.5 m to 3.0m depth including

sorting out and stacking of useful materials and disposing

off the excavated stuff upto 50 Meter lead.(A) Loose or

Filling available excavated earth (excluding rock) in

trenches. plinth, sides of foundations etc. in layers not

exceeding 20 cm. in depth consolidating each disposited

layer by ramming and watering.

Dewatering by pumping set of required capacity including

temporary platform carting pumping at site and fixing the

same in position including all accessories, and fuel and

labour etc . complete.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Providing and laying rubble for appron (each stone

6 weighting not less than 40Kg.) including and packing and

filing in the interestices with quarry-spalls.

230 mm rubble soling below footing 174.00 1041.05 CU.M.

Providing and casting in situ C.C. in grade M-15 (approx.

corresp. to prop. 1:2:4) (proportions as per mix design or

as per Table 9 of IS456 2000 in masses by weigh batching

) using granite, quartzite trap metal of size 6 mm to 20 mm

for RCC work, including scaffolding centering, form

work, needle vibrated consolidation, curing comp. up to

meter depth or height (excluding cost of reinforcement

and neat finishing) with centering and

shuttering/deshuttering etc. comp. for structure for other

than water retaining.

Footing (without form work)

Providing and cast in situ C.C. in grade M-30 proportions

of ingredients as per mix design by weigh batching using

granite, quartzite trap metal of size 12 mm to 20 mm and

or 6 mm to 12 mm including scaffolding centering

8 formwork, needle vibrated consolidation, curing and

hydraulic testing etc. complete (excluding cost of

reinforcement) with centering and shuttering/deshuttering

etc. camp. up to 6 meter height /depth Av. G.L.for all

water retaining structures

Flat bottom slab with shuttering 293.71 9444.95 CU.M.

Vertical Wall (Above 25 cm) 715.00 9295.45 CU.M.

Columns 16.00 10714.55 CU.M.

Floor slab/slab with shuttering 232.00 9444.95 CU.M.

Beams/ ring beams/girders 59.00 9758.90 CU.M.

Lintel/W.Shed/Chhajja 4.00 9444.95 CU.M.

Providing formwork of ordinary timber planking so as to

give a rough finish including centering shuttering strutting

and propping etc. Height of propping and centering below

9 supporting floor to ceiling not exceeding 4 M. and 82.56 173.40 sqm

removal of the same for in situ reinforced concrete and

plain concrete work in. Foundations Footings Bases of

Columns etc. and Mass concrete.

Providing and cast in situ C.C. in grade M-25 proportions

of ingredients as per mix design by weigh batching using

granite, quartzite trap metal of size 12 mm to 20 mm and

or 6 mm to 12 mm including scaffolding centering

formwork, needle vibrated consolidation, curing and

hydrulic testing etc. complete (excluding cost of

reinforcement) with centering & shuttering/ deshuttering

etc. for all water retaining structures.

a) R.C.C. footings & Raft 145.00 9288.55 cmt

b) R.C.C. Columns 32.00 10574.25 cmt

c) R.C.C. beams, lintels and bracket for gantry or chain

pully blocks, plinth beams, tie beams, weather shed etc.

d) R.C.C. slabs and platform 115.00 9288.55 cmt

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Supplying cutting, bending, binding and placing in

position steel as per plan and design and as per ISS

including cost of steel and binding wire for

11 reservoirs/structures only including lift up to 6 meter 216.54 89129.60 M.Ton

height or depth below G.L. for all diameters Do -

deformed (TMT) bars confirming to relevant IS Fe -

grade for all diameters.

Supplying, cleaning, cutting, bending, welding,

fabricating, erecting, structural steel in position

irrespictive of location and levels as per drawings

including handling and transport, etc. complete including

applying two (2) coats of primer red oxide and two (2)

coats of approved quality paints

Brick work using common burnt clay building bricks

having crushing strength not less than 35kg./Sq.Cm. in

foundation and plinth in Cement Mortar 1 : 6 ( 1-Cement :

6-fine sand ) (B) Conventional (upto 10 ton)

Brick masonry in cement mortar (1:5) using common

burnt clay building bricks having crushing strength not

less than 35kg/csmt including scaffolding,curing, etc.

complete for walls, parapets, etc. in Foundation and Plinth

Brick masonry in cement mortar (1:5) using common

burnt clay building bricks having crushing strength not

less than 35kg/csmt including scaffolding,curing, etc.

complete for walls, parapets, etc. at all levels.

Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg./Sq.Cm. in

foundation and plinth in Lime Mortar 1:1.5 (1- Lime putty

:1.5 -fine sand)(B) Conventional

Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg./Sq.Cm. in

foundation and plinth in Lime Mortar 1: 2 (1- Lime putty :

2 -fine sand)(B) Conventional

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for

18 interior plastering upto floor two level and finished even 14772.60 224.79 Smt

and smooth in (i) Cement mortar 1:3 (1-cement:3-sand) &

Finishing with a floating coat of neat cement slurry.

Providing 10mm thick cement plaster in single coat on

brick/concrete walls for interior plastering upto floor two

level and finished even and smooth in (i)Cement mortar

1:3 (1-cement:3-sand)

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

20 mm thick sand faced cement plaster on walls up to

height 10 metres above ground level consisting of 12 mm

20 thick backing coat of C.M. 1 : 3 ( 1-cement : 3-sand ) and 4746.72 300.66 SQ.M.

8 mm thick finishing coat of C.M. 1 : 1 ( 1-cement : 1-

sand ) etc. complete.

Providing and fixing window having extruded

aluminum Colour anodized section frame main

outer size 127mm x 38.10mm x 1.35mm @wt.

1.384kg/m, horizontal Four track member size

vertical member of size 122.20mm x 31.75mm x

1.50mm @1.398 kg/mt with sliding shutters of

horizontal member size 40mm x 18mm x 1.29mm@

0.456kg/mt ,vertical member of size 40mm x 18mm

x 1.29mm @ 0.456 kg/mt with 5 mm thick

transparent bronze colour tinted float glass with

powder coated aluminum fittings and fixtures and

transparent silicon sealant glass fixing to frame as

per details etc complete for window.

Providing and fixing M.S. grills of required pattern

to wooden frames of windows etc. with M.S. flats

22 at required spacings and frame alround, square or 432.00 145.08 Kg

round bars with round headed bolts and nuts or by

screws. (B) ORNAMENTAL GRILL

Providing and fixing rolling shutter of approved make

made of 80 mm. wide M.S. plates inter locked together

entire length and jointed together at the end by locks

mounted on specially designed pipe shafts with bracket

plates. Guide channels and arrangements for inside and

outside locking with push pull operation complete

including the cost of hood cover and spring complete. (B)

Shutters having width 3.5 M. and above

Providing & Refilling in sides of structure with sand

24 incuding watering, ramming, consolidation and dressing 3162.00 460.19 CU.M.

complete in layers not exceeding 20 CM. in depth.

Distempering two coats with oil bound washable

distemper of approved brand & manufacture & of required

shade on wall surface to give an even shade over and &

incl. a priming coat of alkali resistance primer of approved

brand after throughly brushing the surface to give an even

shade after throughly brushing the surface free from

mortar droppings and other foreign matter and also

including preparing the surface even and smooth.

Extra for ditempering with oil bound washable distemper

on ceiling and sloping roofs.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Applying two coats of putty & two coats of primer of

approved brand and manufacture on new wall surface to

26 give an even shade including thoroughly brushing the 1200.00 40.59 Smt

surface free from mortar dropping and other foreign matter

and sand papered smooth.

Finishing wall with weather proof exterior emulsion paint

on wall surface (two coats) to give an required shape even

27 shade after thouroughly brushing the surface to remove all 1996.72 114.53 SQ.M.

dirt, and remains of loose powdered materials. Etc

Providing and laying broken China Mosaic flooring for

terrace using 12 mm to 20 mm broken pieces of glazed

tiles to be laid over Cement mortar 1:3 to plain or slope

28 and to be tempered to bring mortar crème out upto surface 335.01 747.29 Smt

using white cement including rounding of junctions and

extending them upto 15 cm. along the wall, clearing with

water and oxalic acid etc. as directed.

Providing and laying polished Kota stone slab flooring

over 20 mm (average) thick base of cement mortar 1:6 (1

29 cement : 6 coarse sand) laid over and jointed with grey 320.00 1096.33 smt

cement slurry including rubbing and polishing etc.

complete . Avg - 30 mm thick

Providing and laying polished kota stone slab 25mm thick

in risers of steps,skirting Dedo and pillars laid on 10mm

thick cement mortar 1:3 (1-Cement : 3 coarse sand) and

jointed with gray cement slury mixed with pigment to

match the shade of slab including rubbing and polishing

Granite in Jams and Sills of the window and ventilation

31 and Door with one molding as directed by Engineer-in- 33.00 3282.50 smt

Filling in plinth with sand under floors incuding watering,

ramming, consolidation and dressing complete

Providing throating or plaster drip and moulding as

instructed by Engineer in charge.

Conveying, carting and removing of the surplus

excavated stuff from the site to any place within the

34 Municipal limit as directed by the Engineer-in-charge

including loading, unloading, carting, dumping and/or

spreading as directed etc. Comp

Carting from 50mt to 5 Km 468.00 103.26 Cmt

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Providing and Fixing 25 mm X 5.2 mm MS Railling with

three horizontal rows and posts of angle iron of Size

35 mm X 65 mm X 8 mm RCC 150 mm and 1.15 meter 4284.00 88.55 R.M.

height and placed at 1.85 mt/ C/C including painting two

coats and anchorage in CC etc. Complete.

Providing and laying cement concrete for IPS 1:2:4 (1-

cement : 2-coarse sand : 4-graded stone aggregate 20mm

nominal size) laid in one layer and finished with a floating

coat of neat cement. (B) 50mm thick.

Providing , laying and jointing in true line and level

diameter UPVC (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber ring

& fittings conforming to ISI 14735-1999 of approved

make for drainage system pipeline, pipe shall be jointed

with each other with rubber lubricant, pipe shall be fixed

37 on wall using of PVC clamp of the size 110 mm diameter 40.00 835.15 R.M.

x 149 mm lengthn x 145 mm height at every 2000 mm

centre to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc.

imcluding testing of pipes and joints and joined with

adhesive solvent cement including costof all materials.

Providing and laying marble stone slab flooring over

20mm (average) base of cement mortar 1:6 (1-

cement:6coarsesand) or L.M. 1:1.5 (1-lime putty :1.5-

coarse sand )laid and jointed with gray cement slurry

including rubbing and polishing complete. (A) Marble slab

25mm thick (up to 10 ton)

Providing and fixing copper lightning arrestor incl. copper

39 strip and earthling plate etc. complete (incl. cost of 200.00 1009.70 Kg

excavation for earthling plate etc. rate per kgs of copper).

Providing and fixing 50 cm wide M.S. Ladder fabricated

from M.S. Flats 10 mm x 75 mm with 20 mm dia steel bar

40 steps in double rows, @ 30 cm C/C. The include stays of

10 mm x 50 mm flats fixed at 3 meter C/C with welding

anchoring and 3 coats anticorrsive paint.

M.S. Ladder(Without safety cage) 190.74 3392.50 Kg

Providing and fixing PVC pipe of 6Kg./csmt of 140 mm

dia for rain water with shoe.

Providing and fixing depth gauge painted on TW plank

mm / MS plate 4 mm thick float, level indicator sliding

42 wire on standard pullies incl. necessary arrangement to 4.00 6348.00 Nos.

prevent the swinging etc. complete with calibration up to

43 Exhaust Fan 8.00 1949.65 Nos.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Steel work, welded in built up sections framed work

including cutting, hoisting, fixing in position and applying

a priming coat of red lead paint. (A)In beams and joists,

channels angles Tees, flats, with connecting plates or

angle cleats as in main and cross beams. Hip and jack

rafters, purlins conneted to common rafters and the like

8 mm thick Chequred plate

8 mm thick Chequred plate

Painting two coats (excluding priming coat) over new steel

and other metal surfaces with enamel paint, brushing,

interior to give an even shade including cleaning the

surface of all dirt, dust and other foreign matter.

Providing and constructing cofferdam in river basin

including excavation ,filling, middle portion with B.C.soil

(in empty Cement/Gunny bags) to the entire satisfaction of

EIC till completion of the work including dismantling

coffer dam after completion of the work as directed by

Painting Letters for "Capacity of Pumping Station" the

size of letters will be 45 cm height and 50 mm width.

Providing and laying cement concrete 1:3:6 ( 1: Cement :

3- Coarse Sand : 6- CRUSHED stone aggregates 40mm

nominal size) and curing complete excluding cost of

formwork in (A) Foundation & Plinth (more than 10 ton)

Providing and laying controlled cement concrete M.200

and curing complete including the cost of formwork (Only

fresh ply shall be use) but excluding cost of reinforcement

for reinforced concrete work in RCC SLAB

Providing Thermo Mechanically Treated bars (TMT bars)

Fe-415 reinforcement for R.C.C. work including bending,

50 binding amd placing in position complete up to floor two 626.48 67.26 kg

level (more than 10 ton)

Providing and fixing 35 mm thick shutters for

doors,windows and clear story windows including Indian

teak wood frames 12 cm x 7 cm size including anodized

alluminium fixtures and fastenings including primer coat

of approved quality and two coats of oil painting etc

complete. (ii) Fully Panelled

Providing and laying 24" x24" Vitrified 8mm thick tiles

flooring over 20mm base of cement mortar 1:6 on new

surface or fixing on existing flooring by adhesive

52 materials including dismantling existing flooring and 51.84 1397.83 Sq.m

jointed with coloured cement slury including finished with

flush pointing & cleaning the surface etc. complete for

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Providing erecting fixing double coated Syntex of

Equivalent PVC (ISI) Mark Water Tank of Required

Capacity eack with all necessary fittings & connection etc.

complete on Terrace.

Providing and fixing to wall, ceiling and floor CPVC

plumbing systms for hot and cold water( IS 15718, NSF

54 approved ) of the following nominal bore, tube fitting and

clamps including making good the wall ceiling and floor. -

Providing and fixing wsh down water closet (European

type, W.C. Pan) with integral P or S trap including jointing

55 the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1- 4.00 1303.71 Nos.

fine sand) (Seal and cover to be measured and paid for

separately)(A) vitreous China Pattern :(i) in white colour

Providing and fixing chromium plated brass half trun flush

56 cock of approved quality including fixing in pipe line etc. 4.00 314.97 Nos.

complete.(i) 20mm dia.

Providing and fixing 100mm size P or S trap for water

closet squatting pan including jointing the trap with the

pan and soil pipe in cement Mortar 1:1 (1-Cement : 1-Fine

sand)(A) Vitreous China.

Providing and fixing G.I. inlet connection for flush pipe

Providing and fixing plastic seat and cover for wash down

59 water closer with C.P. brass hinges and rubber buffers. (B) 4.00 291.33 Nos.

Black plastic seal and cover.

60 Bib cock 15 mm Heavy duty with cap 4.00 400.58 Nos.

Providing and fixing washbasin with single hole for pillar

tap with C.I. or M.S. brackets painted white including

61 sutting holes and making good the same but excluding 4.00 1414.18 Nos.

fittings.(A) Vitreous China:(ii) Flat Back washbasin

mm x v 400mm size. (i) In white colour.

Providing and fixing chromium plated, bottle trap with

necessary couplings of approved quality for wash basin.

Providing and fixing C.P. brass waste for washbasin or

sink. (B) 40mm dia.

64 Concealed cock 15 mm Heavy duty with cap 4.00 491.30 Nos.

65 C.P. Angle stop cock 15 mm Heavy duty with cap 4.00 407.42 Nos.

66 C.P. Pillar cock 15 mm Heavy duty swan neck 4.00 647.95 Nos.

Providing and fixing S.W. gully trap with C.I. grating

brick masonary chamber and water tight C.I. Cover with

frame of 300mm x 300mm size ( inside ) with standard

weight. Square mouth traps

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Providing and laying (to level or slope) and jointing with

stiff mixture of cement mortar in proportion 1:1 salt glazed

stoneware pipes incl. testing of pipes and joints complete.

Constructing brick masonary chamber for underground

C.I. Inspection chamber and bends with bricks having

crushing strength not less than 35 Kg./Sq.Cm. In C.M. 1:5

C.I.cover with frame ( Light duty ) 455 mm x 610 mm

internal dimensions. Total weight of cover with frame to

be not less than 38 Kg. ( Wt. Of cover 23 Kg. ) and wt. Of

69 frame 15 Kg. ) ( R.C.C. top slab with 1:2:4 mix ( 1-cement 8.00 7180.44 Nos.

: 2-coarse sand : 4-graded stone aggregate 20 mm size )

foundation concrete 1:5:10 inside plaster 15 mm thick

with cement mortar 1:3 finished smooth with a floating

coat of neat cement on walls and bed conc.etc. comp.( iii )

inside dimension 600mm x 850 mm x 450mm deep for

pipe line with three or more inlets.

70 PVC SWR pipes IS 13592 for Drain - 110 mmdia 20.00 265.34 Rmt

71 PVC SWR pipes IS 13592 for Drain - 75 mmdia 20.00 144.65 Rmt

72 PVC SWR Single T" -110 mm dia With Door" 8.00 109.55 Nos.

73 PVC SWR Single T" -75 mm dia With Door" 8.00 59.05 Nos.

PVC SWR Piipe Bend 87.5 degree with door for 75 mm

PVC SWR Piipe Bend 87.5 degree with door for 110 mm

76 PVC SWR Piipe clamp 75 mm 16.00 8.55 Nos.

77 PVC SWR Piipe clamp 110 mm 16.00 12.84 Nos.

PVC SWR Piipe Bend 87.5 degree with door for 75 mm

PVC SWR Piipe Bend 87.5 degree with door for 110 mm

80 PVC SWR WC Connector 110 mm 8.00 128.39 Nos.

81 PVC SWR Vent Cowl 75 mm dia 4.00 9.41 Nos.

82 PVC SWR Vent Cowl 110 mm dia 4.00 19.68 Nos.

83 PVC SWR Piipe Bend 45 degree 75 mm dia 16.00 31.67 Nos.

84 PVC SWR Piipe Bend 45 degree 110 mm dia 16.00 59.05 Nos.

85 PVC SWR Double Y" - 75 mm dia With Door" 16.00 106.99 Nos.

86 PVC SWR Double Y" -110 mm dia With Door" 16.00 174.61 Nos.

Ball Valve ,Gun Metal Wheel Valve 40mm dia. (A)

Copper Metal ,(i) 40 mm dia.

Non Return Valve , Providing and fixing Gun metal check

88 or non-return fullway wheel valve.(E) 40mm dia.(E) 40 4.00 663.43 Nos.

Earthwork in cutting in all sorts of soil and soft murrum

including conveying and spreading the stuff, embankment

89 as and where directed within the estate from the end of the 1359.00 127.74 Cum

cutting with all required lead and lift as directed by

engineer in charge within the estate.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Providing and laying cement concrete 1:2:4 (1Cement : 2-

Coarse sand : 4- graded stone aggregates 20 mm nominal

size) and curing complete excluding cost of formwork in

(A) Foundation and Plinth

Providing and fixing pre-cast concrete kerb stone of gray

cement based concrete block 30cm length,30cm height and

15cm thick of M250 grade concret OF Vyara, Kuber and

91 Asian or equvilaent make as per approved design and 500.00 361.64 Rmt

including excavation for fixing in proper line and

level,filling the joint with C:M 1:3 (1cement:3fine sand)

Graded Granular sub base (GSB)

Providing & laying of compacted thickness of 250 mm

Closed Graded Granular sub base (GSB) in Two equal

layers (each layer should be less than 200 mm)of graded

granular material consisting of river sand, graval, pabbles

and crushed stone aggregate, shingle as per grading - V

given in table 400-1 of the specification MORT&H and

compactor to the required density with 8 - 10 tonne

vibratory roller with plain drum or heavy pneumatic tyred

roller of minimum 200 to 300 KN weight in all seasons as

per MORT&H , maintaining the required slope & grade

during the operation as approved by the engineer in charge

& watering to the proper moisture content and sprinkled

with the help of truck mounted water tank fitted with

suitable arrangement. (fully saturated having CBR value

Wet Mix Macadam (WMM)

Providing, laying, spreading and compacting graded stone

aggregate to wet mix macadam 250 mm thick spacification

including trimix the materials with water at OMC in

mechanical mix plant carriage of mixed materials by tipper

to site laying in uniform layers (Layer should not be more

93 than 200 mm)with paver in sub base/base course on well 755.00 2146.84 Cum

prepared surface and camber with Sensor paver

consolidation by vibratory road roller to achieve the

desired density by using machine crushed chips as per

required gradation mixing with required optimum quantity

of water incl material, labour, plant and machinary and

equipment etc. complete.

Providing and fixing pre-cast Rubber Dye / steel Dye inter

locking concrete block 60mm thick with grade of concrete

M300 pnumatic compressed / vibrated mechanically and

as per approved design

Confirming to IS 15658 : 2006 including 35 mm Sand

layer for levelling and filling the joint with sand in proper

line and level as per guidlines of IRC: SP 63-2018 etc.

Providing cement vata (10cm. x 10 cm. size) quarter round

95 in cement mortar 1:1 including neat cement finishing, 520.00 23.68 Rmt

watering etc. complete.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Filling in Foundation and plinth with murrum or selected

96 soil in layers of 20cm . Thickness including watering , 6040.00 289.06 Cum

ramming and consolidating etc. complete

Providing and laying controlled cement concrete M.200

and curing complete including the cost of formwork '(Only

fresh ply shall be use) but excluding cost of reinforcement

for reinforced concrete work in a) RCC Footing

b)RCC column 48.00 8611.53 Cum

c)RCC Beam 45.00 6445.68 Cum

d)RCC coping 33.00 6057.54 Cum

Providing in line level plumb, fabricating and fixing three

row horizontal barbed wire fencing and punched tape

concertina coil of 9 turns per meter of 610 mm diameter

fixied with clips on top of the angle iron posts. The

punched tape concertina coil having sharp barbs at every

25 mm spacing shall be 0.5 mm thick and 19 mm width

98 and weighting 13 Kg./100 mtr. (Average) as per 550.00 468.00 Rmt.

manufacture's specification. The rate shall also include

providing and fixed 1.20 mt. total long MS angle 40 x

x 6 mm @ 3.00 mt. c/c spacing embedded in RCC column,

angle posts shall be painted with one coats of red oxide

and two coats of enamel paint of approved quality at top

of compound wall.

Labour charges for writing of capital letter "AUDA" in

green plaster of 30 cm height, 25 mm thick and 12 mm

embossed as per given detail in outside of compound wall

as instructed by Engineer in charge.

Fabricating and fixing in position MS structural section

such as flat, pipes, plates, hold fast, anchoring bolts / bars

of required size including fixing, welding and two coats of

100 approved anti corrosive paint over prime coat of red-oxide 650.00 90.00 Kg

including RCC gate column as per drawing etc. complete

as directed by Engineer-in-charge. a)2.2 m height and 6 m

wide main and wicket gate

Box cutting the road surface to proper slope and camber

for making a base in all sorts of soil strata for road work

including removing the excavated stuff and depositing as

directed by engineer in charge within the estate. The item

is including dismanteling of flexible road/ RCC structure

if any as per instruction of Engineer In charge.

Scarifying gravelled macadam or bitumen macadam

surface 6 cm to 10 cm.depth including stacking useful

materials on road side and disposing off remaining stuff.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Earth work for subgrade of 500mm thick having CBR not

less then 8 using yellow earth brought from outside having

PI value less than 15 including breaking clods dressing

with all lead and lift and including watering rolling and

103 consolidation of sub-grade in layers not exceeding 200 27956.50 164.10 Sqm.

mm thickness at O.M.C to required dry density

including filling the depressions which occur during the

process using Vibratory roller 8 to 10 tonne capacity (D)

From Borrow area within 2.0KM. lead

Construction of granular sub-base by providing & laying

of compacted thickness of 300 mm Grading 5th Granular

sub base (GSB) in two layers of graded granular material

consisting of machine cut black trap stone aggregate as

per grading - V given in table 400-1 of the specification

MORT&H and compactor to the required density with

104 vibratory roller in all seasons as per MORT&H , 24609.68 2162.65 CUM

maintaining the required slope & grade during the

operation as approved by the engineer in charge &

watering to the proper moisture content and sprinkled with

the help of truck mounted water tank fitted with suitable

arrangement. (fully saturated having CBR value minimum

Providing, laying, spreading and compacting graded stone

aggregate to wet mix macadam spacification including

premixing the materials with water at OMC in mechanical

mix plant carriage of mixed materials by tipper to site,

laying in uniform layers (Layer should not be more than

200 mm)with paver in sub base/base course on well

prepared surface and camber with Sensor paver

105 consolidation by vibratory road roller to achieve the 14553.00 2464.37 CUM

desired density by using machine crushed chips as per

required gradation mixing with required optimum quantity

of water incl material, labour, plant and machinary and

equipment etc. complete by plant mix method. ( Using

mechanical paver ). The rate is including

excavation/cutting and levelling the surface before laying

WMM as directed by engineer in charge.

Providing and applying primer coat with bitumen emulsion

SS1 on prepared surface of granular Base including

clearing of road surface and spraying primer at the rate of

0.70 kg/sqm using mechanical means.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Providing & laying compacted 50 mm thick dense graded

bituminous macadam (DBM) Grade-II in Single layer using 100-

120 TPH batch type HMP with tack coat at the rate of 2.5 kg /

10 m2 (VG10) in each using crushed aggregates of specified

grading premixed with bituminous binder @ 4.5% ( VG - 40)

bitumen by weight of total mix and filler , transporting the hot

mix to work site laying with a hydrostatic paver finisher with

sensor control with full road carpet width (Single screed) or as

directed by Engineer in charge to the required grade, level and

alignment, rolling with smooth wheeled roller, intermediate

rolling 8-10 tonnes dead weight or vibratory roller & pneumatic

tire roller of 12 to 15 tonnes weight having sufficient width and

pressure & the finishing rolling shall be done with 6 to 8 tonnes

smooth wheeled tendem rollers to acheive the desired

compaction as per MORT&H specification etc complete in all

respects. The agency shall have to get the mix design done from

approved laboratory and submit to the Engineer in charge for

approval.(Va = 3.5% & Vbe= 11.50% must be considered in

mix design ) If the asphalt (bituminous) content is more than

above, the agency shall have to bear the cost of additional

asphalt. The payment shall be done on the permissible field

density achieved on the site instead of density derieved in the

mix design. ( The density obtained by mix design above

MT/M3 shall be boarn by agency )

Providing and laying compacted 40 mm thick Bituminous

Concrete ( BC ) Grade -II in single layer using 100-120 TPH

batch type hot mix plant and using asphalt as a tack coat @

kg / 10 sq.m (VG 10) in each using crushed stone aggregateof

specified gradation and filler, Premix with VG-40 grade

bitumenous binder at 5.40 % by total weight of mix & filler

incl. transporting the hot mix to work site and laying with

hydrostatic paver finisher having sensor control with Full road

carpet width ( Single screed) or as directed by Engineer in

charge to the required grade, level and alignment, rolling with

smooth wheeled roller, intermediate rolling 8-10 tonnes dead

weight or vibratory roller & pneumatic tire roller of 12 to

tonnes weight having sufficient width and pressure & the

108 finishing rolling shall be done with 6 to 8 tonnes smooth 5054.00 4830.52 MT

wheeled tendem rollers to acheive the desired compaction as

per MORT&H specification etc complete in all respects. The

agency shall have to get the mix design done from approved

laboratory and submit to the Engineer in charge for approval

(Va = 3.5% & Vbe= 11.50% must be considered in mix design

). If the asphalt (bituminous) content is more than above, the

agency shall have to bear the cost of additional asphalt. The

payment shall be done on the permissible field density achieved

on the site instead of density derieved in the mix design. ( The

density obtained by mix design above 2.36 MT/M3 shall be

boarn by agency )

Providing and applying asphalt painting with bitumen of

VG 40 grade on bitumenous surface including clearing of

road surface and spraying Bitumen at the rate of 0.60 kg /

sqm using mechanical means.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Road Marking with Hot Applied Thermoplastic

Compound with Reflectorizing Glass Beads on

Bituminous Surface by Providing and laying of hot

applied thermoplastic compound 2.50 mm thick including

110 reflectorizing glass beads @ 250 gms per sqm area, 12377.00 367.72 Sqm

thickness of 2.5 mm is exclusive of surface applied glass

beads as per IRC:35 .The finished surface to be level,

uniform and free from streaks and holes etc. complete as

Construction of dry lean cement concrete Sub- base over a

prepared sub-grade with coarse and fine aggregate

conforming to IS: 383, the size of coarse aggregate not

exceeding 25 mm, aggregate cement ratio not to exceed

15:1, aggregate gradation after blending to be as per table

111 600-1, cement content not to be less than 150 kg/ cum, 393.80 2991.75 Cum

optimum moisture content to be determined during trial

length construction, concrete strength not to be less than

10 Mpa at 7 days, mixed in a batching plant, transported to

site, laid with a paver with electronic sensor, compacting

with 8-10 tonnes vibratory roller, finishing and curing.

Construction of un-reinforced, dowel jointed, plain cement

concrete pavement over a prepared sub base with approve

grade cement @ 400 kg per cum, coarse and fine

aggregate conforming to IS 383, maximum size of coarse

aggregate not exceeding 25 mm, mixed in a batching and

mixing plant as per approved mix design, transported to

site, laid with a fixed form or slip form paver, spread,

compacted and finished in a continuous operation

including provision of contraction, expansion,

construction and longitudinal joints, joint filler, separation

membrane, sealant primer, joint sealant, debonding strip,

dowel bar, tie rod, admixtures as approved, curing

compound, finishing to lines and grades as per

drawing.For M-350

Providing and laying cement concrete 1:5:10 (1- Cement :

5-Coarse sand : 10- hand broken stone aggregates 40 mm

nominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth

RCC precast M.H. Frame & Cover Manufacture, supply &

Delivery at store or at site of work precast RCC M.200

Frame & cover suitable to drainage M.H. and as per type

design & Drawing including cost of reinforcement

M.S.Angles or Flat, curing mold work etc.

House Connection Chamber light duty A) Frame

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Providing and laying cement concrete work 1:2:4 (1-

Cement : 2- Coarse sand : 4- graded stone aggregates

mm nominal size) and curing complete excluding cost of

formwork and reinforcement for reinforced concrete work

in (B) Slabs, landing, shelves, Balconis , Lintels, Beams,

Girders and Cantilever upto floor two level.

Providing formwork of ordinary timber planking so as to

give a rough finish including centering shuttering strutting

and propping etc. height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and

removal of the same for in situ reinforced concrete and

plain concrete work in. (H) (1) Sides and soffits of Beams

Beam Haunchings cantilevers Girders Bressumers and

Lintels not exceeding 1 M. in Depth.

Providing and laying cement concrete work 1:2:4 (1-

Cement : 2- Coarse sand : 4- graded stone aggregates

mm nominal size) and curing complete excluding cost of

formwork and reinforcement for reinforced concrete work

in (A) Foundations, footings, Base or columns and Mass

concrete For Benching

Providing and casting in situ C.C. in grade M-20

(proportions as per mix design or as per table9 of IS456

2000 in masses by weigh batching ) using granite,

quartzite trap metal of size 6 mm to 20 mm for RCC work,

118 including scaffolding centering, formwork, needle vibrated 121.00 6085.80 Cum

consolidation, curing complete up to 6 meter depth or

height (excluding cost of reinforcement and neat finishing)

with centering and shuttering/deshuttering etc. complete

for structure other than water retaining (Below G.L)

Excavation for pipe line trenches for water supply,

sewerage line, manhole etc. all with shoring and struting if

required as per required gradient and line including safety

119 provisions using site rails and stacking excavated stuff

including up to all required lead cleaning the site etc.

complete for all lifts and strata as specified.

In all sorts of soil and soft murrum

(A) Upto 1.5 Mt. dpt.from G.L. 168658.16 102.35 Cu.M.

(C) 3.0 Mt TO 4.50 Mt depth 24920.00 118.45 Cu.M.

(D) 4.5 Mt. TO 6.00 Mt. Depth 6030.00 125.35 Cu.M.

(E) 6.0 Mt TO 7.50 Mt depth 640.00 129.95 Cu.M.

Providing and supplying D. I. pipes for following nominal

bore diameter with internal cement mortar lining

including all taxes, insurance, transportation, freight

charges, octroi, inspection charges, loading, unloading,

120 conveyance to departmental stores, stacking etc. complete.

(IS 8329-2000). For sewerage project cement mortor

lining shall be with sulphate resistance cement.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

500 mm Dia (DI PIPE K-9) 3733.00 7909.00 Rmt

600 mm Dia (DI PIPE K-9) 2641.00 10309.00 Rmt

250 mm Dia (DI PIPE K-9) 1869.00 2998.00 Rmt

(All type of fittings) Providing and supplying at store or

site of work incl. freight, loading, unloading, stacking,

121 insaurance & all taxes etc. complete

Rate for Specials Upto 300mm dia 2271.59 148.00 Kg

Rate for Specials Above 300mm dia 22549.81 151.00 Kg

Lowering, laying and jointing C. I. S & S Spun pipes

suitable for Tyton joints / Mortar lined D. I. Pipes of

various classes with CI / MS specials of following

122 diameters in proper position, grade and alignment as

directed by Engineer-in-charge including hydraulic testing

etc. comp. (tyton Joint)

500 mm Dia (DI PIPE K-9) 3695.00 358.80 Rmt

600 mm Dia (DI PIPE K-9) 2590.00 464.60 Rmt

250 mm Dia (DI PIPE K-9) 1850.00 146.05 Rmt

Providing and supplying ISI mark CI D/F Sluice Valves as

per IS:14846 (Latest Edition) of following class and

diameter including all taxes, insurance, transportation,

123 freight charges, octroi, inspection charges, loading,

unloading, conveyance to departmental stores, stacking

500 mm Dia PN-1 With gear operated (PD type short

body) Sluice valve

600 mm Dia PN-1 With gear operated (PD type short

body) Sluice valve

250 mm Dia PN-1 With gear operated (PD type short

body) Sluice valve

providing and supplying C. l. Air valves of approved

make & quality of following class and diameter including

all taxes, insurance, transportation, freight charges, octroi,

inspection charges, loading, unloading, conveyance to

departmental stores, stacking etc. complete.

100 mm Dia Air valves double acting (DS2) 6.00 5267.00 No

150 mm Dia Air valves double acting (DS2) 4.00 12384.00 No

80 mm Dia Air valves double acting (DS2) 3.00 3660.00 No

Lowering, laying and jointing in position following C. I. /

D/F Reflux valves, Butterfly valves, Sluice valves and Air

125 valves including cost of all labour, jointing material,

including nut bolts and giving satisfactory hydraulic

testing, etc. complete.

500 mm Dia PN-1 With gear operated (PD type short

body) Sluice valve

600 mm Dia PN-1 With gear operated (PD type short

body) Sluice valve

250 mm Dia PN-1 With gear operated (PD type short

body) Sluice valve

100 mm Dia Air valves double acting (DS2) 6.00 604.90 No

150 mm Dia Air valves double acting (DS2) 4.00 695.75 No

80 mm Dia Air valves double acting (DS2) 3.00 472.65 No

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Constriuction of Valves Chamber in Brick or bela stone

masonary,locally available in CM 1:6 foundation concrete

150mm thick in C.C 1:4:8 of trap metal size 25mm to

40mm thickk cement plaster in C.M. 1:3 and cement

pointing outside in CM 1:3 and top cover of precast RCC

slab 100 mm thick(with key hole in two parts with handels

or MS bar etc. comp. as given size) up to 1 meter depth

126 from Gl to pipe invert level including comp. civil work but

excluding cost of excavation & refilling with cast in situ

RCC slab in one single piece with fixing of CI -MH

frame & cover (excluding. cost of CI MH-frame & cover)

with 23 mm thick brick wall in C.M 1:6

Size of chamber 0.90 m x 0.90 m and 1.0 mt. deep With

precast slab in two parts 15 mm

Providing and supplying ISI Standard R.C.C. pipes(of

Sulphate Resisting Cement) in standard lengths of

following class and diameter suitable for either collar

127 joints or rubber ring joints including all taxes, insurance,

transportation, freight charges, octroi, inspection charges,

loading, unloading, conveyance to departmental stores,

Note : One collar should be supplied with each full length

plain ended RCC pipe, cost included in rates below. One

rubber ring should be supplied with each full length

socketed pipe, cost included in rates below.

(D1) 300 mm dia (NP3 Class) 51570.00 755.00 Rmt.

(D2) 300 mm dia (NP4 Class) 10292.00 1087.00 Rmt.

(E1) 350 mm dia (NP3 Class) 787.00 879.00 Rmt.

(E2) 350 mm dia (NP4 Class) 1741.00 1379.00 Rmt.

(F1) 400 mm dia (NP3 Class) 759.00 1150.00 Rmt.

(F2) 400 mm dia (NP4 Class) 837.00 1873.00 Rmt.

(G1) 450 mm dia (NP3 Class) 380.00 1361.00 Rmt.

(G2) 450 mm dia (NP4 Class) 626.00 2179.00 Rmt.

(H1) 500 mm dia (NP3 Class) 354.00 1485.00 Rmt.

(H2) 500 mm dia (NP4 Class) 24.00 2337.00 Rmt.

(I1) 600 mm dia (NP3 Class) 1174.00 1946.00 Rmt.

(I2) 600 mm dia (NP4 Class) 1171.00 2994.00 Rmt.

(J1) 700 mm dia (NP3 Class) 551.00 2879.00 Rmt.

(J2) 700 mm dia (NP4 Class) 908.00 3900.00 Rmt.

(K1) 800 mm dia (NP3 Class) 25.00 3175.00 Rmt.

(K2) 800 mm dia (NP4 Class) 139.00 5575.00 Rmt.

(M1) 1000 mm dia (NP3 Class) 9.00 4821.00 Rmt.

(O1) 1200 mm dia (NP3 Class) 30.00 5899.00 Rmt.

(P1) 1400 mm dia (NP3 Class) 946.00 7587.00 Rmt.

(Q1) 1600 mm dia (NP3 Class) 387.00 11167.00 Rmt.

(R1) 1800 mm dia (NP3 Class) 1059.00 13608.00 Rmt.

Lowering, laying and jointing R. C. C. pipes in C. M. 1:1

1/2 of following diameters in proper position, grade and

alignment at all level as directed by Engineer-in-charge

128 including conveyance from stores to site of work, labour,

giving hydraulic testing as per ISI code.

(D1) 300 mm dia (NP3 Class) 51570.00 136.85 Rmt.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

(D2) 300 mm dia (NP4 Class) 10292.00 136.85 Rmt.

(E1) 350 mm dia (NP3 Class) 787.00 152.95 Rmt.

(E2) 350 mm dia (NP4 Class) 1741.00 152.95 Rmt.

(F1) 400 mm dia (NP3 Class) 759.00 174.80 Rmt.

(F2) 400 mm dia (NP4 Class) 837.00 174.80 Rmt.

(G1) 450 mm dia (NP3 Class) 380.00 196.65 Rmt.

(G2) 450 mm dia (NP4 Class) 626.00 196.65 Rmt.

(H1) 500 mm dia (NP3 Class) 354.00 217.35 Rmt.

(H2) 500 mm dia (NP4 Class) 24.00 217.35 Rmt.

(I1) 600 mm dia (NP3 Class) 1174.00 262.20 Rmt.

(I2) 600 mm dia (NP4 Class) 1171.00 262.20 Rmt.

(J1) 700 mm dia (NP3 Class) 551.00 308.20 Rmt.

(J2) 700 mm dia (NP4 Class) 908.00 308.20 Rmt.

(K2) 800 mm dia (NP4 Class) 164.00 347.30 Rmt.

(M1) 1000 mm dia (NP3 Class) 9.00 431.25 Rmt.

(O1) 1200 mm dia (NP3 Class) 30.00 506.00 Rmt.

(P1) 1400 mm dia (NP3 Class) 946.00 586.50 Rmt.

(Q1) 1600 mm dia (NP3 Class) 387.00 663.55 Rmt.

(R1) 1800 mm dia (NP3 Class) 1059.00 747.50 Rmt.

Providing & Constructing Precast RCC Manhole in RCC

M-40 grade Controlled concrete as per drawing, in OPC

including excavation, 80 mm thick P.C.C. in M-15,

129 Reinforcement in TMT-500, PVC Foot steps, Providing &

fixing FRC Manhole frame & cover including inside

epoxy paint complete etc.

For 250 mm to 600 mm Dia. Pipe ( Upto 4.0m Depth)

For 250 mm to 600 mm Dia. Pipe ( Above 4.0m Depth)

1.5 m Dia.- 4.01 m to 4.99 m Depth 59.10 9779.00 Rmt.

1.5 m Dia.- 5.01 m to 5.99 m Depth 30.40 11341 Rmt.

1.5 m Dia.- 6.01 m to 6.99 m Depth 12.40 11400 Rmt.

1.5 m Dia.- 7.01 m to 9.99 m Depth 0.50 15296 Rmt.

1.8 m Dia.- 5.01 m to 5.99 m Depth 3.70 14744.00 Rmt.

Providing and erecting C. I. and MS ventilating columns

15 cms. dia. with C.I. ornamental cap and Min 6.00 Mtr.

Height (Height may be varying as per site) base fixed

firmly with necessary foundation with one coat of red lead

oxide paint and one coat of any approved colour with

130 cms, dia.10 Mt.in length with 0.35mt*0.35mt* M100

Encasing, M.S pipe connection with M.H. including

excavation and jointing as required etc. complete. as per

drawing and Fixing inposition

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

For 6 Mtr. Height ( 6 Mt MS pipe) 225.00 38911.40 No.

Dewatering by pumping set of required capacity including

temporary platform carting pumping at site and fixing the

131 same in position including all accessories, and fuel and 9600.00 21.07 HP/Hr

labour etc. complete.

Shoring or timbering for trench with 50 mm thick planks

and suitable size struts etc. complete.

Refilling the pipeline trenches incl. ramming, watering,

consolidating desposal of surplus stuff as directed within a

radius of 3 km.do- with selected soil brought from outside

including all lead

do- with selected soil brought from outside including all

Drilling of 900mm dia Horizontal borehole for watermain

pipeline under the railway tracks incl all strata with

requried length incl fixing of 800mm dia M.S.casing pipe

of minimum 12mm thick Or IRS Casing Pipe with welding

pushing etc complete Providing & fixing various size of

pipe for 406.4 mm/457mm/508mm dia watermain of

G.I/M.S pipe of minimum 6.3mm thick for railway

permises as per instruction & regulations of Railway

authority & under supervision of Railway authority incl

Provinding & suppllying fixing of spacer at specified

interval if required between Casing pipe and water main,

ISI make sluice valve of required size at both side of

railway boundry with construction of brickedge pavement

incl C:C encasing 1:3:6 in 10mtr length of pipe at both

side. Incl Provinding & fixing of M.S/Iron Manhole frame

with cover for valve chamber with loacking arregment etc.

complete with all material labour fabrication,hydralic

testing of pipe & valve etc complete for 45 mt

Length.which includes horizontal pushing and with open

Without Water main & with MS Casing Pipe 100.00 29026.87 Rmt

Drilling of 900mm dia Horizontal borehole for watermain

pipeline crossing under the road incl in all strata with

135 requried length incl fixing of 800mm dia M.S/RCC casing

pipe with pushing etc complete various size of pipe for

406.4 to 508mm dia watermain

Without Water main & with MS Casing Pipe-800 thick:12 30.00 25712.67 Rmt

Drilling of 1300mm dia Horizontal borehole for

watermain pipeline crossing under the road incl in all

strata with requried length incl fixing of 1200mm dia

M.S/RCC casing pipe with pushing etc complete various

size of pipe for 559 to 711mm dia watermain. (for 45 Mtr.

Without Water main & with MS Casing Pipe-1200

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Drilling of 600mm dia Horizontal borehole for pipeline

crossing under the road incl in all strata with requried

length incl fixing of 400mm dia M.S/RCC casing pipe

137 with pushing etc complete various size of pipe for 273.1 to

355.6 mm dia (For 45 mt Length)

Without Water main & with MS Casing Pipe 1294.00 13344.78 Rmt

Drilling of Horizontal bore hole for water main pipeline

under the Railway / Road tracks in all strata with required

length including fixing of M.S.(or as specified by Railway

/ Road authority) casing pipe of suitable size and

Thickness. Rate includes the cost of Drilling of bore hole

Casing pipe & welding pushing etc complete but

excluding the cost of water main, valves and other items.

Entire work should be as per Approved Drawing and as

per instruction of Railway / Road authority for Following

diameter of Bore hole. for MS pipe

Horizontal Drilling-600:& MS Casing Pipe-500 thick:8 24.00 10540.90 Rmt

Drilling of Horizontal bore hole for water main pipeline

under the Railway / Road tracks in all strata with required

length including fixing of M.S.(or as specified by Railway

/ Road authority) casing pipe of suitable size and

Thickness. Rate includes the cost of Drilling of bore hole

Casing pipe & welding pushing etc complete but

excluding the cost of water main, valves and other items.

Entire work should be as per Approved Drawing and as

per instruction of Railway / Road authority for Following

diameter of Bore hole. for MS pipe

Horizontal Drilling-2100:& MS Casing Pipe-2000 thick: 36.00 81551.95 Rmt

Construction of cast in situ RCC manhole of 1500 mm

internal diameter and 3 m depth (upto invert of manhole)

140 in M 30 CC grade with opening of 1.2 m for MH cover. 1.00 258876.5 Rmt

Without MH cover

HDPE DWC Pipe : Providing and supplying of Class SN8

Structured Wall polyethelene Piping systems (Pipe with

online/offline coupler and elastomeric sealing ring) with

non-smooth External Annular Corrugated and Smooth

Internal Surfaces (Double Wall) for non-pressure

141 underground Sewerage & Drainage application as per

EN:13476-3 including all local and central taxes,

transportation, freight charges, octroi, inspection charges,

loading, unloading, conveyance to the departmental stores

etc. complete.(ID Dia)

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Lowering, laying and jointing of class SN 8 structured

wall ( External Annular Corrugated & Smooth Internal

surface) Polyethylene Piping and fittings with the help of

coupler ( on line / off line ) attached with one end of pipes,

sliding over the elastomeric sealing rubber ring placed on

the specified valley of the corrugation at the spigot end,

lowering the same into the trench at all level, laying on the

lower bedding (constructed at bottom of trenches) at

142 prescribed gradient,depth & alignment ,testing the water

tightness of the joints, ensuring the continuity tests of

specified pipe segments etc. complete as per

drawing,specifications & detailed engineering, including

carriage of pipes & fittings from site stacks to the place of

laying etc. as per direction of Engineer-in-charge.

Sequential Batch Reactor Technology (SBR

TECHNOLOGY) - 30 MLD

Designing, providing, constructing, hydraulic testing,

commissioning and giving satisfactorily trials of STP

consisting of Inlet Chamber, Screen

Chamber, Detritus Tanks, Distribution Chamber and SBR

Basins, Sludge Sump, Chlorine Contact Tank, Chlorinator

Room / Shed, Sludge

Dewatering Equipment, necessary piping work with

required valves, gates, drains, pathways, Administration

Block cum Laboratory,

Laboratory Equipments, Internal Roads, Pathways,

143 compound wall, Tools and Plants, complete as turnkey job

with all involved civil, electrical,

instrumentation and mechanical works inclusive of

following items, units as per detailed specifications for

civil, electrical and mechanical

components with all duties and taxes etc. complete to

achieve BOD < 10ppm, TSS < 10ppm,Biological TN <

10ppm & PO4 < 2ppm to get

recyclable quality of water for industrial / agricultural

purposes. The Coagulant Dosing System shall be provided

as an optional/ back up. All units shall be interconnected

with administration building by Suitable or RCC overhead

UNITS INCLUDED:

* PRIMARY TREATMENT

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Inlet Chamber :

Designing, providing, and constructing RCC (M:30) inlet

chamber for the peak flow as per CPHEEO Manual

including necessary excavation in

all types of strata including walkway all around the

periphery. Inlet chamber having minimum HRT of

seconds, each compartment will have

steel gates with extension rod, head stock operating

wheels. GI pipe railing etc. The work includes providing

and making necessary

arrangements to connect the flow to screen chamber by

approach channel as directed and as per specifications.

Screen Chamber :

Designing , providing, constructing, testing and

commissioning of Two approach channels (min 4.5 m

long), mechanically cleaned bar rack

screen (6 mm clear opening 10 mm the. flats), Escalator

screens, with 100% standby manual fine screen (10 mm

clear opening) MOC: SS316,

CI sluice gates (one before screen & one after screen)

designed fast per CPHEEO Manual in RCC (M -30),

including inlet pipe/ channel

from inlet chamber, outlet pipe / channel to detritus tank,

free board of 0.5 m minimum, RCC walkway 1.2 m wide

with GI pipe railing. RCC

stair case of 1.2 m width from GL to screen chamber. with

operating platform and belt conveyor system incl. panel &

push bottom switch at

local level as well as MCC room for two way control.

Designing, providing and constructing grit Chamber-

Detritus or vortex type or aerated type (100% standby),

mechanically operated in RCC (

M 30) capable of removing 100% of 0.2 mm size particle

and above, having specific gravity 2.40, HRT of 1 minute

at average flow (Detritus

Tank), horizontal velocity not exceeding 0.30 m/sec

(Detritus Tank) at peak flow with suitable arrangement of

separation of grit from

putrescible solids. Inlet and outlet channels of required

sizes as may be required to connect the flow to connecting

unit etc. Complete including

hydraulic testing for water tightness of structure having

minimum FB of 0.3 m, wash out arrangement to Grit

chamber and platform 1.2 m wide

RCC walkway with GI pipe handling shall be provided. A

pit for collecting grit conveyed by conveyor shall be

provided. It should be suitable to

handle the grit for carting. All arrangements shall be as

detailed specifications and as directed.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Parshall flume having head loss limited to 0.15 m with

necessary flow measuring devices/meter consisting of

digital indicator in LPS & MLD

SECONDARY TREATMENT

Designing, providing and constructing in RCC (M 300),

CASP basins for biological removal of BOD along with

built-in nitrification-denitrification,

Bio-P removal in compartments to handle combine flow of

1 DWF incoming flow and recirculation flow including

construction of

selector compartments and providing 1.2 m wide clear

approach walkways, expansion joints wherever necessary,

including foundations etc as

per specifications. Peak factor shall be 2, F/M ratio shall

be 0.15, complete with air blowers, fine diffused aeration

grid with Retrievable type

installation equipment and FB 0.5 m and SWD as

required. DO level in basin to be minimum 2 mg/l

complete with "Oxygen Uptake Rate"

control system and all related instruments, Stainless steel

decanters and automation works. MLSS concentrations

shall be 3000 - 5000 mg/l or

more, MLVSS to MLSS ratio to be 0.6-0.7. HRT shall be

min. 13.5 hrs and SRT suitable for fully digested sludge.

SBR process shall have

independent steps like Fill & aeration,

Settling(Sedimentation/clarification), Decanting without

overlapping each other. Since it is complete

batch process, filling will not be acceptable during settling

or Decanting. Minimum decanting depth shall not be less

than 2.20 m. The system

should work on a gravity influent condition. No

influent/effluent equalization tanks or flash filling is

accepted. It should have all other related

SRT shall be suitably provided to achieve N, P removal.

Since these are the technology driven plants, bidders has

to adopt well established,

well tested and proven, IIT/ NEERI evaluated/approved

SBR process /specifications and at least 50 % of the

tendered capacity has been in

successfully operating condition as per the outlet criteria

mentioned in above in Government organizations of India

since last two years

including one year of standard defect liability period.

Bidder has to tie-up with the well qualified technology

provider who having experience in

India at least 50 % of the tendered capacity with 1 year O

& M experience in government organizations of India.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Process Air Blowers or aeration Device

The Plant should be based on Dissolved Oxygen/Oxygen

Uptake Rate Control with VFD driven Aeration Device.

The Aeration System shall be

designed for 110 % Capacity of the design Air

requirement. The aeration Blower/Aeration Device shall

be having 100% installed standby unit.

Air diffuser shall be of disk/ tubular type, retrievable. The

wetted part of the aeration system of non-corrosive

materials such as UPVC.

Blowers shall be housed in process air blower building.

The minimum area of the building is 20 sq.m. and height

of 5m (min). Blowers shall be housed in process air

blower building. The minimum area of the building is

sq.m. and height of 5m (min).

Raw sludge pump house:

Raw Sludge Sump minimum HRT of 30 minutes & depth

of sludge limited to 2 m, 4.5 m minimum diameter,

separate panel room outside the

Chlorine Contact Tank:

Designing providing and constructing chlorine contact

chamber of adequate capacity to deal with 1 DWF average

flow. The chlorine contact

tank should be of 30 min capacity, during average flow to

achieve 99.99 % coliform reduction. Chlorine dose shall

be maintained as per

standard provisions, including designing, providing and

constructing water supply provision for chlorination,

including providing dewatering

and by pass arrangement jointing to final effluent mains

and outlet weir etc complete. The effluent quality should

match with the standards laid

down by Gujarat pollution control board and as per

obligatory provision and as detailed specification and as

directed by engineer in - charge.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Chlorinator and Chlorinator Room/Tonner Room:

Designing, providing and constructing chlorinators

vacuum type 2 Nos, (1 working+ 1 stand by) with auto

switchover facility and having

capacity for dosage of adequate chlorine to ensure

% coliform reduction as per obligatory provisions and

detailed specifications with

necessary provision of having chlorinator room of

adequate size. The chlorinator equipment shall include

cost of chlorine cylinders/tonner,

piping, valves, measuring and controlling equipment,

safety devices , lifting equipment, etc. complete as per IS -

10553 ( part II) 1982. The

tonner room should have minimum 3 MT capacity Hoist

for loading and unloading facility. Tonner storage should

be distinctly isolated and

should be for minimum storage space as directed in the

design specification and as per gas laws 1981 and factory

act shall be provided. All

other matching amenities shall be provided, Minimum

MT gantry rail shall be provided for full length of tonner

room at 6 m height from level

of tonner room, with outlet chamber and treated effluent

outlet channel etc complete as per detailed specification.

Sludge treatment

Sludge Thickner with equipments:

Solids loading rate of 25-35 kg/m2/day, Designing,

providing & constructing watertight of sludge thickener-

gravity type (picket fence) in RCC

(M-30) with inlet & outlet pipes, central feed well, sludge

it & sludge removal arrangement, grouting wherever

necessary with walkway all

around of 1.20m with GI pipe railing interconnecting CI

pipes all complete as per specifications, having bottom

slope 1:6 & min. 4.5m SWD

with necessary fixed bridge scraper arrangement as per

detailed specifications & necessary inlet & outlet

arrangement. All other arrangement

as per detailed specifications. (One unit upto 10 MLD and

two units for more than 10 MLD). Min sludge

concentration in thickened sludge shall

Sludge Holding Sump :

Designing, providing and constructing of sludge sump and

pump house of appropriate size with pumps, ceiling height

minimum 6 m over sump

for discharging sludge to centrifuge using CI pipe

complete as per detailed specification.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Sludge Dewatering Equipment Room with Centrifuge

or belt press or screw press or Filter Press or Combi-

machine or Bag Type:

Designing, providing constructing and installing including

foundation etc. Centrifuge or belt press or screw press or

Filter Press or Combimachine

or bag Type to handle the sludge flow as per

specifications, with appropriate inlet and outlet provision,

sludge dewatering unit drain

etc. Complete as per specifications.

Sludge/ filtrate Pumps

a) Capacity to pump sludge in 1 hour with 100% standby

(20-25% efficiency, "C" value to be adopted 50% than that

of water to calculate

b) Filtrate from thickening and dewatering to be conveyed

only by PVC 10 kg/sq.cm.

Inlet, outlet ,wash water inlet – only CI D/F and minimum

size of 200 mm as per approved make/brand.

All types gauges and meters required for O & M as per

design of specified make/brand.

Necessary Instrumentation and control as per

Designing, providing and constructing appropriate outfall

sewer of RCC NP2 pipe, to discharge treated effluent from

outlet chamber after

chlorination tank to the disposal point at outlet battery

limit of STP including necessary chambers for inspection

and cleaning including

necessary excavation, dewatering, refilling, concrete

encasing/bedding concrete steps to reach the disposal/

nallah bed level. pitching and

energy dissipation chamber in nallah portion etc. complete

up to 500 m length RCC NP2 pipe line and including all

By pass arrangements

RCC pipes with manholes and C.I. sluice gates (MH to be

raised above TWL of adjacent unit)

Piping work in CI-LA Class including Sluice valves,

Reflux Valves, MS Gates:

Providing laying and jointing pipes other than those

already included in the above items for interconnection by -

pass drains etc. of all units

including adequate numbers of manhole chambers. The

item includes excavations, refilling and hydraulic testing

of pipes, valves, gates,

accessories and cost of jointing materials. The items

includes required channels with gates for interconnection

of units by pass drains etc for

all units as directed etc complete as per detailed

specifications.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Administrative Building cum Laboratory (G+1):

Designing, providing and constructing administrative

building, office cum Laboratory including stores. This

shall be a building having

appropriate carpet area and ground floor and at first floor

complete as per specifications including necessary

excavation, foundation in RCC M

200 framed structure B. B masonry (11- class in C.M. 1:6)

20 mm cement plaster in C.M 1:3 inside and outside

painting. Aluminium door and

window with glass panels, mosaic tile flooring and skirting

and all other allied items, fixtures fastening electrification

arrangement water supply

arrangement etc complete.

a) Ground floor to accommodate administrative office &

b) First floor to accommodate Office of the Plant In

Charge, air monitoring equipments to

measure wind direction & speed, hydrogen sulphide

concentration etc.

Laboratory equipments

Laboratory equipment (as per specifications),

beautification, telephone and intercom arrangement

and wireless system.

Furniture and Office Equipments, Office furniture

(Make: Godrej/ or similar approved quality) as

per specifications

Ventilation and Safety equipments as per

Sanitary blocks

Carpet area – 15 square meter minimum up to 25 MLD

and 25 square meter above 25 MLD (or as

Maintenance Workshop of size as per specification

Air blower Building with Air Blowers:

Capable of delivering adequate free air for aeration device

with suitable pressure (100% standby).

MCC Room of minimum 9 m x 6 m clear inside with

safety measures, approval of various

statutory/ central/ foreign authority as applicable

Electric installation

Both internal and external including entire plant area (as

Electric installation - Sub Station Room as per

specifications.

DG room with DG sets, as per electric load and

specifications (50 % energy requirement).

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

General Infrastructure Development:

Scope also includes, Designing, providing and

constructing general infrastructure development such as

internal roads of minimum 6 mtr wide,

compound wall for STP site, internal street and building

lightings, pathways of minimum 1 m wide to access all

STP units and Entrance Gate in

MS fabrication, etc. all complete as per specifications and

directed by engineering in charge.

Asphalt road (Minimum 4.5 m) to connect all units from

main gate of plot.

Compound Wall as per the plant layout, long the boundary

of STP site (considering plant layout

for intermediate and ultimate build out capacity and 33%

landscaping area).

Green Belt (33% landscaping area) as per specification

Capacity of Plant (MLD)

Cost of 30 MLD treatment plant 1.00 252589450.00 No

1. Fine screens (SS 316) are of mechanically cleaned type for

working unit and manual bar screen type (SS 316) for standby

2. Upto 5 MLD Capacity STP chlorination may be done by

using sodium hypochlorite solution. Above 5 MLD capacity gas

chlorinator to be

3. Gravity sludge thickener is not provided upto 3 MLD

capacity STP. Sludge will be collected into sludge sump &

pumped directly to sludge

dewatering system.

4. Filter press or Bag Type dewatering can be provided for

STP's upto 5MLD capacity.

5. Chlorinator room not provided for STP upto 3 MLD.

6. Boundary wall, gate, Internal plant roads, storm water drains,

site clearance, landscaping is considered in scope. Plant road

7. All water retaining structures are in M-30 grade of concrete.

8. Lead for excavation is considered as 500m.

9. Grade of steel used is Fe

10. Peak factor considered for design for plants 2 to 5 MLD is

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

11. The rates mentioned above STP are considering sites

falling in Seismic Zone III.

12. Structural design criteria approved by technical

committee shall be applicable for design.

13. Hydraulic design of the plant shall be considered with

free fall discharge of treated sewage to local water body

(above HFL). Hydraulic loss

shall be worked out for peak flow condition and shall not

exceed 4.5m in any circumstances unless otherwise site

specific condition and

approved by technical committee.

14. The cost of sewage pumping station and rising main is

15. Makes of equipment shall be approved by

16. The rates includes excavation, refilling and throwing

away extra stuff as directed by the Engineer in Charge.

17. All other details shall be as per design criteria and

detail specifications.

Filling in Foundation and plinth with murrum or selected

soil in layers of 20cm . Thickness including watering

ramming and consolidating etc. complete as per instrcuted

by Engineer In Charege

SUBMERSIBLE SEWAGE NON-CLOG VERTICAL

Supply, Installation, Testing and Commissioning (SITC)

of Non-clog submersible pump of following duty

parameters along with LV AC submersible induction

motor air filled dry type pump-motor set shall be of

materials of construction and must have all required

accessories viz. automatic coupling device, double guide

pipes, chain with shackles, Submersible Power & control

cable (copper flexible & stranded type conductor of reqd.

cores & size for each pump motor set) & length of 20 m

long each run with necessary electrical termination

connection at junction box / starter panels, RCC

foundation with duck foot bend for auto coupling &

delivery bend and PMU etc. as per equipment data sheet

and detailed technical specifications and also including in

scope any other parts / accessories / fittings required to

complete the work in all respects & satisfactory operation

Capacity: 410 m3/hr,

Induction Motor rating mini. 75 kW or as per

For MPS-1 TO STP

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

SUBMERSIBLE SEWAGE NON-CLOG VERTICAL

Supply, Installation, Testing and Commissioning (SITC)

of Non-clog submersible pump of following duty

parameters along with LV AC submersible induction

motor air filled dry type pump-motor set shall be of

materials of construction and must have all required

accessories viz. automatic coupling device, double guide

pipes, chain with shackles, Submersible Power & control

cable (copper flexible & stranded type conductor of reqd.

cores & size for each pump motor set) & length of 20 m

long each run with necessary electrical termination

connection at junction box / starter panels, RCC

foundation with duck foot bend for auto coupling &

delivery bend and PMU etc. as per equipment data sheet

and detailed technical specifications and also including in

scope any other parts / accessories / fittings required to

complete the work in all respects & satisfactory operation

Capacity: 419 m3/hr,

Induction Motor rating mini. 55 kW or as per

SUBMERSIBLE SEWAGE NON-CLOG VERTICAL

Supply, Installation, Testing and Commissioning (SITC)

of Non-clog submersible pump of following duty

parameters along with LV AC submersible induction

motor air filled dry type pump-motor set shall be of

materials of construction and must have all required

accessories viz. automatic coupling device, double guide

pipes, chain with shackles, Submersible Power & control

cable (copper flexible & stranded type conductor of reqd.

cores & size for each pump motor set) & length of 20 m

long each run with necessary electrical termination

connection at junction box / starter panels, RCC

foundation with duck foot bend for auto coupling &

delivery bend and PMU etc. as per equipment data sheet

and detailed technical specifications and also including in

scope any other parts / accessories / fittings required to

complete the work in all respects & satisfactory operation

Capacity: 469 m3/hr,

Induction Motor rating mini. 75 kW or as per

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

SUBMERSIBLE SEWAGE NON-CLOG VERTICAL

Supply, Installation, Testing and Commissioning (SITC)

of Non-clog submersible pump of following duty

parameters along with LV AC submersible induction

motor air filled dry type pump-motor set shall be of

materials of construction and must have all required

accessories viz. automatic coupling device, double guide

pipes, chain with shackles, Submersible Power & control

cable (copper flexible & stranded type conductor of reqd.

cores & size for each pump motor set) & length of 20 m

long each run with necessary electrical termination

connection at junction box / starter panels, RCC

foundation with duck foot bend for auto coupling &

delivery bend and PMU etc. as per equipment data sheet

and detailed technical specifications and also including in

scope any other parts / accessories / fittings required to

complete the work in all respects & satisfactory operation

Capacity: 159 m3/hr,

Induction Motor rating mini. 30 kW or as per

MPS TO KARAI NETWORK

Supply, Installation, Testing and Commissioning of ISI

mark CI D/F Sluice Valve as per IS 14846 PN 1.0 with

Manually / Electrically Gear operated of following sizes

with SS 304 seat rings, SS rising spindle with all hot

dipped galvanised hardwares, bolts, nuts & washers,

gaskets including all taxes, insurance, transportation,

148 freight charges, Inspection Charges, loading unloading, 6.00 170535.00 No.

conveyence to pump house, stacking, security etc.

complete as per IS and Specification.

Size: 250 mm NB (Electrically Gear Operated - On

Delivery of each Pump)

Supply, Installation, Testing and Commissioning of ISI

mark CI D/F Sluice Valve as per IS 14846 PN 1.0 with

Manually / Electrically Gear operated of following sizes

with SS 304 seat rings, SS rising spindle with all hot

dipped galvanised hardwares, bolts, nuts & washers,

gaskets including all taxes, insurance, transportation,

freight charges, Inspection Charges, loading unloading,

conveyence to pump house, stacking, security etc.

complete as per IS and Specification.

Size: 300 mm NB (Electrically Gear Operated - On

Delivery of each Pump)

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Supply, Installation, Testing and Commissioning of ISI

mark CI D/F Sluice Valve as per IS 14846 PN 1.0 with

Manually / Electrically Gear operated of following sizes

with SS 304 seat rings, SS rising spindle with all hot

dipped galvanised hardwares, bolts, nuts & washers,

150 gaskets including all taxes, insurance, transportation, 2.00 137790.00 No.

freight charges, Inspection Charges, loading unloading,

conveyence to pump house, stacking, security etc.

complete as per IS and Specification.

Size: 150 mm NB (Electrically Gear Operated - On

Delivery of each Pump)

MPS TO KARAI NETWORK

Size: 100 mm NB (Manually Operated - On header for

MPS TO KARAI NETWORK

Supply, installation, testing and commissioning of double

flanged CI Dual Plate Check Valve conforming to API

594 Class 300 with CS dual door, hinge pin & stop pin of

SS 410 , springs of AISI 304 and seat of SS 304 , along

with all required accessories, gaskets and hardwares,etc.

and as per specification.

Size : 250 mm NB (On delivery of each Pump)

Supply, installation, testing and commissioning of double

flanged CI Dual Plate Check Valve conforming to API

594 Class 300 with CS dual door, hinge pin & stop pin of

SS 410 , springs of AISI 304 and seat of SS 304 , along

152 with all required accessories, gaskets and hardwares,etc. 5.00 36186.00 No.

and as per specification.

Size : 300 mm NB (On delivery of each Pump)

Supply, installation, testing and commissioning of double

flanged CI Dual Plate Check Valve conforming to API

594 Class 300 with CS dual door, hinge pin & stop pin of

SS 410 , springs of AISI 304 and seat of SS 304 , along

with all required accessories, gaskets and hardwares,etc.

and as per specification.

Size : 150 mm NB (On delivery of each Pump)

MPS TO KARAI NETWORK

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

SITC of Manually / Electrically Gear operated ISI mark

CI D/F Butterfly Valve as per IS 13095, PN 1.0 with

sleeve of EPDM & disc, shaft & internal parts of SS

410 along with gaskets and all other necessary

hardware etc. of following diameter including all taxes,

insurance, transportation, freight charges, Inspection

Charges loading unloading, conveyence to pump house

stacking, security etc. complete as per IS and

Size: 350 mm NB (Electrically Gear operated On pump

Header line after FM)

1 Nos at Header

SITC of Manually / Electrically Gear operated ISI mark

CI D/F Butterfly Valve as per IS 13095, PN 1.0 with

sleeve of EPDM & disc, shaft & internal parts of SS

410 along with gaskets and all other necessary

hardware etc. of following diameter including all taxes,

insurance, transportation, freight charges, Inspection

Charges loading unloading, conveyence to pump house

stacking, security etc. complete as per IS and

Size: 350 mm NB (Electrically Gear operated On pump

Header line after FM)

1 Nos at Header

SITC of Manually / Electrically Gear operated ISI mark

CI D/F Butterfly Valve as per IS 13095, PN 1.0 with

sleeve of EPDM & disc, shaft & internal parts of SS

410 along with gaskets and all other necessary

hardware etc. of following diameter including all taxes,

insurance, transportation, freight charges, Inspection

Charges loading unloading, conveyence to pump house

stacking, security etc. complete as per IS and

Size: 450 mm NB (Electrically Gear operated On pump

Header line after FM)

1 Nos at Header

SITC of Manually / Electrically Gear operated ISI mark

CI D/F Butterfly Valve as per IS 13095, PN 1.0 with

sleeve of EPDM & disc, shaft & internal parts of SS

410 along with gaskets and all other necessary

hardware etc. of following diameter including all taxes,

insurance, transportation, freight charges, Inspection

157 Charges loading unloading, conveyence to pump house 1.00 134674.00 No.

stacking, security etc. complete as per IS and

Size: 150 mm NB (Electrically Gear operated On pump

Header line after FM)

1 Nos at Header

MPS TO KARAI NETWORK

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

SITC of CI Temper Proof Air Valve with Isolation

Sluice Valve as per IS 14845 PN-1.0 & IS-14846 PN-1.0

respectively with SS304 float, gun metal nozzle, complete

hardware's, bolts, nuts & washers, gaskets etc. including

all taxes, Insurance, Transportation, freight charges,

Inspection charges, loading, unloading, conveyance to

departmental stores, stacking, security etc. as per IS and

Size: 100 mm NB - Pn 1.0 (On Header pipe O/S. the pump

house before interconnecting junction)

SITC of CI Temper Proof Air Valve with Isolation

Sluice Valve as per IS 14845 PN-1.0 & IS-14846 PN-1.0

respectively with SS304 float, gun metal nozzle, complete

hardware's, bolts, nuts & washers, gaskets etc. including

all taxes, Insurance, Transportation, freight charges,

159 Inspection charges, loading, unloading, conveyance to 1.00 11599.00 No.

departmental stores, stacking, security etc. as per IS and

Size: 50 mm NB - Pn 1.0 (On Header pipe O/S. the pump

house before interconnecting junction)

MPS TO KARAI NETWORK

Supply, installation, testing and commissioning of double

flanged Expansion Bellows confirming to EJMA/IS

standard with PN 1.0 rating & all necessary St.St.

160 Size : 250 mm x 300 mm ( L ) (On Delivery of Each 6.00 7745.00 No

Size : 350 mm x 300 mm ( L ) (On header Line near

MPS-1 TO STP 2.00 12840.00 No

Supply, installation, testing and commissioning of double

flanged Expansion Bellows confirming to EJMA/IS

standard with PN 1.0 rating & all necessary St.St.

161 hardware''s. 5.00 10200.00 No

Size : 300 mm x 300 mm ( L ) (On Delivery of Each

Size : 450 mm x 300 mm ( L ) (On header Line near

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Supply, installation, testing and commissioning of double

flanged Expansion Bellows confirming to EJMA/IS

standard with PN 1.0 rating & all necessary St.St.

162 hardware''s. 2.00 4656.00 No

Size : 150 mm x 300 mm ( L ) (On Delivery of Each

MPS TO KARAI NETWORK

Size : 150 mm x 300 mm ( L ) (On header Line near

FlowMeter) 1.00 4656.00 No

MPS TO KARAI NETWORK

G.I. PIPES & FITTINGS:

Supply, installation, connection with equipments as

required, testing and commissioning of GI pipe

conforming to IS-1239 , Medium Duty with coupling, tee,

bend, union, elbow, flanges , etc as all required fittings for

connection complete with gaskets, hardware, and required

163 accessories as per IS & Specifications 80.00 898.00 RMT

Size: 100 mm NB (Header drain Pipe & for Air Valve

MPS TO KARAI NETWORK

Size: 50 mm NB (Air Valve Pipe)

MPS TO KARAI NETWORK

DI PIPES & SPECIALS

Providing and supplying D. I. D/F K-9 grade pipes for

following nominal bore diameter with internal cement

mortar lining including all taxes, insurance, transportation,

freight charges, octroi, inspection charges, loading,

unloading, conveyance to departmental stores, stacking

etc. complete. (IS 8329-2000).

DI Pipe K-9 D/F

Size: 250 mm (For Delivery of Each Pump)

Size: 350 mm (Header pipe) Length is tentative and to be

considered as per actual site condition. 25.00 10071.00 RMT

Size: 350 mm (Header pipe) Length is tentative and to be

considered as per actual site condition.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

DI PIPES & SPECIALS

Providing and supplying D. I. D/F K-9 grade pipes for

following nominal bore diameter with internal cement

mortar lining including all taxes, insurance, transportation,

freight charges, octroi, inspection charges, loading,

165 unloading, conveyance to departmental stores, stacking 75.00 7769.00 RMT

etc. complete. (IS 8329-2000).

DI Pipe K-9 D/F

Size: 300 mm (For Delivery of Each Pump)

Size: 450 mm (Header pipe) Length is tentative and to be

considered as per actual site condition.

DI PIPES & SPECIALS

Providing and supplying D. I. D/F K-9 grade pipes for

following nominal bore diameter with internal cement

mortar lining including all taxes, insurance, transportation,

freight charges, octroi, inspection charges, loading,

unloading, conveyance to departmental stores, stacking

etc. complete. (IS 8329-2000).

DI Pipe K-9 D/F

Size: 150 mm (For Delivery of Each Pump)

MPS TO KARAI NETWORK

Size: 150 mm (Header pipe) Length is tentative and to be

considered as per actual site condition. 20.00 3597.00 RMT

MPS TO KARAI NETWORK

Manufacture, Supply & Delivery of Ductile Iron Flange

bends, tees, reducers or any other specials as per BS-EN-

545/1995 Class - A Series K12 Suitable for use with DI

pipes manufactured as per IS:8329 / 1994 delivery of

specials is to be made to site of works anywhere in gujarat

including all taxes, loading, unloading, carting, stacking,

insurance, inspection charges, octroi etc. complete. -

80 to 300 mm dia

MPS TO KARAI NETWORK

MPS-2 TO STP 1665.00 155.00 kg

MPS TO KARAI NETWORK

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

SITC of Electric Actuator Gear operated C.I. Sluice Gate

conforming to AWWA C 501 or IS : 13349 - 1992 Class -

1 with rising spindle, single faced, wall thimble mounted,

handwheel, flange back frame, head stock, Spindle with

supports brackets having length as specified or to suit site

168 condition, suitable for seating as well as unseating water 5.00 480250.00 Nos

head, complete in all respect.

Gate Size : 900 mm X 900 mm - approx. 12 m spindle

length (at inlet line) Conventional Bottom Closing or

suitable Closing

SITC of Electric Actuator Gear operated C.I. Sluice Gate

conforming to AWWA C 501 or IS : 13349 - 1992 Class -

1 with rising spindle, single faced, wall thimble mounted,

handwheel, flange back frame, head stock, Spindle with

supports brackets having length as specified or to suit site

condition, suitable for seating as well as unseating water

head, complete in all respect.

Gate Size : 1000 mm X 1000 mm - approx. 12 m spindle

length (at inlet line) Conventional Bottom Closing or

suitable Closing

SITC of Electric Actuator Gear operated C.I. Sluice Gate

conforming to AWWA C 501 or IS : 13349 - 1992 Class -

1 with rising spindle, single faced, wall thimble mounted,

handwheel, flange back frame, head stock, Spindle with

supports brackets having length as specified or to suit site

condition, suitable for seating as well as unseating water

head, complete in all respect.

Gate Size : 400 mm X 400 mm - approx. 9 m spindle

length (at inlet line) Conventional Bottom Closing or

suitable Closing

MPS TO KARAI NETWORK

BAR SCREEN - MANUAL

Supply, Installation, Testing and Commissioning of

Manuall Bar Screen having bar size of 10 mm x 50 mm

and clear spacing between bars of 25 mm, MOC SS-304

and lifting hook etc with all required accessories and

171 hardware. 3.00 186450.00 Nos

Size : 2000 mm (L) X 2000 mm (W)

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

BAR SCREEN - MANUAL

Supply, Installation, Testing and Commissioning of

Manuall Bar Screen having bar size of 10 mm x 50 mm

and clear spacing between bars of 25 mm, MOC SS-304

and lifting hook etc with all required accessories and

Size : 1000 mm (L) X 1000 mm (W)

MPS TO KARAI NETWORK

BAR SCREEN - MECHANICAL

Supplying, installing, testing, and commissioning of

Mechanical Fine Screen suitable for sewage pumping

station inlet channel, designed to automatically remove

fine solids and floating debris from incoming raw sewage.

The screen shall be of robust construction in stainless steel

SS304/SS316, consisting of screen frame, fine bars,

automatic raking system, drive motor with gearbox,

control panel, and necessary supports and guide structures.

The system shall ensure uninterrupted screening with

automatic removal of screenings to a designated disposal

area, thereby protecting pumps and downstream

Size : 2000 mm (L) (or as per actual requirement) X

E.O.T. CRANE WITH HOIST

Supply, installation, testing & commissioning single girder

type fully electrically operated EOT crane with electrically

operated hoist, class II duty, geared travelling trolley with

seven meter lift complete with long travel rail track (40

mm sq. bar), moving or cross girder, all three motions

electrically operated by suitable rating motor IP 54, control

panel & down pendant control block, brake, safety device,

cables form motor to starter panel & other required

accessories & tested as per IS Specifications.

Note: Minimum as specified capacity or higher as per

requirement such that EOT crane capacity is min.1.25

times of the pump, motor OR single heaviest component to

be lifted within pump house.

Capacity : 5 Ton. (for Pump Room)

'Lift : 6-12 m (or as per actual site condition)

Span: 6-9 m (or as per actual site condition)

Bay length: 20 m (or as per actual site condition)

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

E.O.T. CRANE WITH HOIST

Supply, installation, testing & commissioning single girder

type fully electrically operated EOT crane with electrically

operated hoist, class II duty, geared travelling trolley with

seven meter lift complete with long travel rail track (40

mm sq. bar), moving or cross girder, all three motions

electrically operated by suitable rating motor IP 54, control

panel & down pendant control block, brake, safety device,

cables form motor to starter panel & other required

175 accessories & tested as per IS Specifications. 1.00 416250.00 Nos

Note: Minimum as specified capacity or higher as per

requirement such that EOT crane capacity is min.1.25

times of the pump, motor OR single heaviest component to

be lifted within pump house.

Capacity : 2 Ton. (for Pump Room)

'Lift : 6-12 m (or as per actual site condition)

Span: 0-6 m (or as per actual site condition)

Bay length: 6 m (or as per actual site condition)

MPS TO KARAI NETWORK

SITC of Electrically Operated Chain Hoist & Electrically

operated Trolley, suitable to operate on Mono Rail Girder

having motorised motion in vertical lifting & cross travel,

manufactured as per IS:6547-1972-Class-II & IS-3177-

Class-II, complete with electrically operated chain hoist &

Electically operated geared trolley, brake, chain-gear,

motors, safety device, pendant push button, starter panel,

cables from motor to starter panel and all other required

accessories like limit switches, panel, power supply system

(Fastoon cable type), fasteners, epoxy painting, etc. tested

for over load as per IS complete as per specifications and

complete in all respect.

Capacity : 1 Ton. Min. (for Manual Screen-lifting)

'Lift : 12 m as mini. or as per site req.

(w/o MONORAIL GIRDER & MS supporting structure)

Note: (1) Minimum as specified capacity or higher as per

requirement such that ECH capacity is min.1.25 times of

the pump/motor OR single heaviest component to be lifted

within pump house.

Chain Pulley Block

Providing chain pulley block with triple gear arrangement,

lifting hook, laod chain & hand chain & locking device

Capacity : 1 Ton. Min. (for Manual Screen-lifting)

'Lift : 10 m as mini. or as per site req.

MPS TO KARAI NETWORK

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Providing, Supplying at site of work with freight, loading,

unloading carting, etc. including all taxes and duties

complete such as joints, channels, angles, plates, iron rails,

etc. below 10 mm thickness as per relevant IS and as per

178 specification 8000.00 64.84 KG

MPS TO KARAI NETWORK

Labour Charges for lowering, laying, Fixing with

fabrication various size section of MS such as joints

channel, angles, plates, etc Complete as per relevant IS

and as per specification.

MPS TO KARAI NETWORK

INSTRUMENTATION WORK PRESSURE

MEASURMENT SYSTEM

Supply, installation, testing & commissioning of Bourden

type Pressure Guage glycerene filled having 150 mm dial

with necessary fittings / accessories (Manifold valve,

nipples, etc. shall be in SS 316 only) as per specifications

& complete in all respects.Pressure gauge shall be

provided only Pump delivery and on header line.

(On delivery of each pump & on Header line).

Range : 0 - 6 kg / sq.cm.

MPS TO KARAI NETWORK

Supply, installation, testing and commissioning of

Digital Pressure Transmitter along with, manifold valve,

required fittings, tubing (all valves, fittings, tubings, etc.

shall be in SS 316 only) all accessories, hardware, etc.

complete in all respects as per specifications and having

following measurement ranges:

Range : 0 - 6 Kg/cm2 (On Delivery of each pump and

MPS TO KARAI NETWORK

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

LEVEL MEASURING SYSTEM

Ultrasonic Type Level Transmitter with Remote Display :

Design, Supply, Installation, Testing and Commissioning

of NOn Contact Ultrasonic Type Level Transmitter with

Remote Display.

The sensor should be non contact type, field mounting

type, housing shall have minimum IP65 protection, PP/

PVC Sensor MOC, with sensor to transmitter cable.

Remote Indicator cum Transmitter:

Microprocessor based indicator with LED / LCD digital

display,panel/ wall mounting type, power supply shall be

Accesories: Mounting bracket, nut, bolts etc as per system

requirement and Hook up diagram of the Instruments.

Meas. Range: upto 15 m at Wet well

MPS TO KARAI NETWORK

ELECTRO MAGNETIC FLOWMETER

Supply, installation, testing and commissioning of remote

type Full Bore Electromagnetic flow meter comprising of

IP-68 Sensor, IP-65/66 remote transmitter with 10m cable

between sensor and transmitter,Panel mounted flow

indicator cum Totalizer along with all mounting

accessories, hardware, etc. complete in all respect and as

per specs and shall have following size and measurement

range. The scope also includes necessary connection with

Meter Size : 350 mm (At Header)

Pipe size: 350 mm

Pipe Material : DI

ELECTRO MAGNETIC FLOWMETER

Supply, installation, testing and commissioning of remote

type Full Bore Electromagnetic flow meter comprising of

IP-68 Sensor, IP-65/66 remote transmitter with 10m cable

between sensor and transmitter,Panel mounted flow

indicator cum Totalizer along with all mounting

accessories, hardware, etc. complete in all respect and as

184 per specs and shall have following size and measurement 1.00 226181.00 Nos.

range. The scope also includes necessary connection with

Meter Size : 450 mm (At Header)

Pipe size: 450 mm

Pipe Material : DI

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

ELECTRO MAGNETIC FLOWMETER

Supply, installation, testing and commissioning of remote

type Full Bore Electromagnetic flow meter comprising of

IP-68 Sensor, IP-65/66 remote transmitter with 10m cable

between sensor and transmitter,Panel mounted flow

indicator cum Totalizer along with all mounting

accessories, hardware, etc. complete in all respect and as

per specs and shall have following size and measurement

range. The scope also includes necessary connection with

Meter Size : 150 mm (At Header)

Pipe size: 150 mm

Pipe Material : DI

MPS TO KARAI NETWORK

PLC BASED CONTROL PANEL FOR SPS

Supply, Installation, Testing & Commissioning of PLC

Based Instrument control Panel with panel mounted 10 "

colour touch screen HMI, 4G or Latest GPRS modem with

ethernet port / Such suitable port for Remote data

transmission to Existing Central as well as Zonal SCADA,

SIM card for remote data tranmission facility,

Communication port for MFM . Instrument Control Panel

'(PLC Enclosure / Panel ) with necessary PLC based logic

and wiring , Min. 1 kVA online UPS (with 30 min backup

alongwith filter for harmonic, suitable rating SMF inbuilt

batteries alongwith battery charger and all other

accessories as per standard), etc. complete in all respects

and as per specs with PLC having minimum I/O count of

64DI / 64DO / 16AI /12AO. These are the minimum IO

requirement if any other IO,s required to complete the

work contractor shall be provide the same without any

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

PLC BASED CONTROL PANEL FOR SPS

Supply, Installation, Testing & Commissioning of PLC

Based Instrument control Panel with panel mounted 10 "

colour touch screen HMI, 4G or Latest GPRS modem with

ethernet port / Such suitable port for Remote data

transmission to Existing Central as well as Zonal SCADA,

SIM card for remote data tranmission facility,

Communication port for MFM . Instrument Control Panel

'(PLC Enclosure / Panel ) with necessary PLC based logic

187 and wiring , Min. 1 kVA online UPS (with 30 min backup 1.00 1243000.00 No.

alongwith filter for harmonic, suitable rating SMF inbuilt

batteries alongwith battery charger and all other

accessories as per standard), etc. complete in all respects

and as per specs with PLC having minimum I/O count of

32DI / 32DO / 16AI /12AO. These are the minimum IO

requirement if any other IO,s required to complete the

work contractor shall be provide the same without any

MPS TO KARAI NETWORK

SITC of Licensed SCADA Software (Latest Version) for

Central Monitoring & Control System of Sewage Pumping

Stations (SPS) and Sewage Treatment Plant (STP),

including supply, installation, testing and commissioning

of SCADA software capable of real-time centralized

monitoring and control of all SPS and STP units from a

central control room, as well as local monitoring and

control from individual SPS and STP locations. The

software shall support seamless integration with

PLCs/RTUs over standard protocols (Modbus TCP/IP,

188 IEC 60870, etc.) and provide functionalities including 1.00 1200000.00 NOS.

graphical HMI, data logging, alarm management,

historical trends, and automated reporting. The license

shall support the required number of tags/nodes and

include configuration for both central and local HMIs.

Complete in all respects and with all required accessories

and hardware to run the software and system including one-

year warranty, operator training, OEM support, and

1) I5 PC with 8 GB RAM 1TB Hard Disk & 32” Monitor

2) 1 KVA UPS for 1 Hr. Backup

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

INSTRUMENT CABLE & ACCESSORIES

'Supply, Laying, Installation, Connection, Termination,

& Commissioning of Instrument Cables, along with

cable glands, lugs, cable trays, required junction boxes,

fittings and accessores as per specs.

The unit rate shall include

a. Supply, loading & unloading of the cable at site from

store. B. Shifitng of cable from site store to place of

c. Fixing of cable clamps, brackets, supports, route

markers etc. where ever required to fix the cables safely.

d. Excavation, back filling and levelling of ground

alongwith laying of fine sand, protection bricks and other

necessary civil material for laying cables outside the

e. Testing and submission of sketches & reports of all the

MPS TO KARAI NETWORK

MPS TO KARAI NETWORK

MPS TO KARAI NETWORK

INSTRUMENT CABLE TRAY

Supply & laying GI perforated type cable trays with

returned edge / flange, fabricated from 2.0 mm thk sheet

steel in the standard length of 2.5 mtrs, duly hot dipped

galvanized after fabrication as per IS 2629-1989 / IS 4759-

1984 including accessories such as coupler plates/ fish

plates, bends, tees, reducers, elbows, covers and electro-

galvanized hardware etc, erected on existing support as per

specification and instruction of Engineer-in-charge.

100 x 35 mm - Perforated type

MPS TO KARAI NETWORK

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

CABLE END TERMINATION AND CONNECTION :

'Supply, fixing, connection, testing and commissioning

of double compression brass cable glands and crimping

type Bimetalic lugs / sockets with necessary tools and

equipments as specified in specifications and IS complete

in all respects. The glands and lugs / sockets shall be

suitable for cable size and type mentioned above. The job

also includes earthing the glands and armour of the cable

with common earth bar or flexible copper mesh as

MPS TO KARAI NETWORK

MPS TO KARAI NETWORK

MPS TO KARAI NETWORK

11 kV Two Pole Structure Assembly:

SITC of 11 kV double pole 9 meter high structure made of

6" X 3" 'I" section girder, 4" X 2" channels, clamps, nuts,

bolts, stay wires including earthing system with following

accessories duly connected with ACSR conductors as per

approved drawing & in compliance with requirement of

(a) 11 kV, 200 A drop out fuses with Synthetic Resin

Bonded Paper (SRBP) tubes: 1 Set (01 piece per phase).

192 (b) 11 kV, 400 A G.O.D. switch complete with earth 3.00 120663.00 Each

switch, insulators, operating handle with galvanised pipe,

square bar: 1 Set.

(c) 11 kV lightning arrestor with clamps: 3 Nos.

(d) 11 kV Disc Insulators (70KN): 3 Nos.

(e) 11 kV Pin Insulators (5KN): 3 Nos.

(f) 20 mm dia. GI Stay Sets Complete: 2 Set.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

HT SWITCHGEAR PANEL

Supply, installation, testing & commissioning both side

extensible, Indoor type HV Switchgear panel confirming

to IS-3427, IS-2516 (Part- I & II.sec.1 ) & IEC-60056 &

IEC-62271-100/200 for use on 3phase, 50 Hz, unearthed

AC supply system and having breaking/ ruptuing capacity

of 500 MVA (26.3 kA for 3sec) complete with spring

charged mechanism, ON-OFF mechanical push button,

operation counters, Breaker TNC switch, Breaker L/R

switch, necessary auxiliary switches, closing coil, shunt

trip, protection relays & Indicators etc., complete. The

panel shall comprise of air insulated busbars provided with

heat shrinkable PVC sleeves. The VCB trolley shall

comprise of three vacuum interrupters with epoxy support

insulators and self aligning finger type isolating contacts

and necessary mechanical interlocks, safety shutters,

isolating plugs. Enclosure shall be openable from front as

well as rear end. The breaker shall be Manual cum

motorised mechanism with following accessories.

a) 96 x 96 mm square flush mounting type Ammeter &

Volt meter with selector switches b) Multi function meter

c) Double core, cast resin type current transofrmer having

ratio as per requirement, one core for metering & one core

for protection having required class of accuracy. d)

Instantaneous under voltage relay & Temperature rise

tripping Relay, e) Triple pole IDMTL two over current

and one earth fault relay with current setting range 50-

200% and 10-40% f) Electrical closing. coil & shunt trip

coil operating on 110 V DC. g) Auxiliary relay for anti

pumping device. h) Three limb, drawout type, feeder

connected, cast resin insulated, three phase Potential

transformer having ratio & burden as per reqirement &

Class 0.5 accuracy. i) Annunciator Windows, Common

Hooter / Alarm bell operating on 230 AC/ 110 V DC. j)

Cable boxes suitable to terminate 3 core XLPE cable of

required size (As per design). k) 230V AC to 110 V DC

power pack for closing & tripping circuit common. l)

Breaker ON-OFF, Auto trip and spring charged indicators.

m) Phase indicating & panel illumination lamps with plug

socket. n) Space Heater with Thermostat.

11 kV HV Switchgear Panel- Comprising of 630 A

Vacuum circuit breaker for 1 no. Incomer, 2no. O / G

feeders for 11/0.433 kV distribution transformers

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

11 kV (Earthed / Unearthed) Grade Cable- Aluminium

Supply, laying, testing & commissioning of 6.35 / 11 kV

(E) grade, XLPE insulated, stranded Aluminium

conductor, galvanised steel flat strip / round wire

armoured, extruded PVC type ST2 sheathed, heavy duty

cable (to be laid on wall surface with necessary clamps / in

existing cable trench / cable trays / conduit / pipe sleeves

at road crossing or floor as per site requirement)

conforming to IS: 7098 (Part2)

& IEC: 60502 (Part-2) of following sizes:

3 Core x 240 Sqmm

From 2 Pole Structure to HT Panel & HT Panel to

Cable Terminations / Jointing Kits for 6.6 kV (UE) /

kV (E) grade XLPE Cable

Providing & fitting heat shrink cable termination / jointing

kits for 6.6 kV (UE) / 11 kV (E) grade XLPE insulated

cable including necessary earth connectivity connection,

material & consummables making the termination/ joint

complete ensuring the joint resistance is within

the permissble limit as per IS, of following types & sizes:

Outdoor Terminations Kit suitable for - 3 Core x

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

DISTRIBUTION TRANSFORMER

Providing, erecting, testing & commissioning approved

make oil immersed ONAN cooled, double wound, core

type indoor / outdoor copper wound 11KV/ 433V step

down transformer of following capacities operating on

phase, 50 Hz 4 wire & neutral earthed system

continuously rated for a full temperature rise in oil not

exceeding 45 Deg.C.at maximum ambient temp. of

Deg. C. complete with necessary radiator first filling of

new transformer oil & standard fitting as below

complying with IS 1180( Part 1 ):2014 standards with

energy efficiency level

Off load tap changing range steps +2.5% to -5% on H.V

for variation should be provided. The H.V. shall be

connected Delta & Secondary with star connection. The

transformer should have cable-end boxes on H.T. side

suitable for up to 3 core 150 sq.mm. XLPE cable & on

L.T. side suitable for bus duct or cables as per requirement

complete with test certificates from manufacturers

1. Oil conservator with filling Hole & Cap - One No.

Thermometer pocket with 6" dial type thermometer switch

alarm & trip contacts- Two nos. 3. Silica-gel breather

with charge- One No. 4. Plain oil level gauge - One

No. 5. Drain / Sampling / Filter valve- One No. 6. Top

196 Filter Valve - One No. 2.00 671787.02 Nos.

7. Explosion vent with Diaphragm - One No. 8. Rating

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

7. Explosion vent with Diaphragm - One No. 8. Rating

& Diagram plate - One No. 9. Additional neutral

bushing for earthing - One No. 10. Bi directional

Roller - Four Nos. 11. Earthing terminals - Two Nos.

Lifting lugs - Two Nos. 13. Air release plug. - One No.

Double float buchholz relay with Alarm and trip

contacts. 15. Control cable as required from Transformer

to VCB Panel is to be provided with necessary connection

to VCB relays for protection. as per IS 1180 level-1

(A) 250 KVA - Cat.III

Max. allowable loses at 50 % of rated load is 2.79 KW

and at full load is 7.77 KW

Note: Transformer shall be suitable for parallel operation.

Minimum requirement shall be as below:

Both transformer shall have " Identical X/R ratio, phase

angle shift, polarity, phase sequence, frequency, position

of tap changer. Turns ratio & voltage ratio"

DISTRIBUTION TRANSFORMER

Providing, erecting, testing & commissioning approved

make oil immersed ONAN cooled, double wound, core

type indoor / outdoor copper wound 11KV/ 433V step

down transformer of following capacities operating on

phase, 50 Hz 4 wire & neutral earthed system

continuously rated for a full temperature rise in oil not

exceeding 45 Deg.C.at maximum ambient temp. of

Deg. C. complete with necessary radiator first filling of

new transformer oil & standard fitting as below

complying with IS 1180( Part 1 ):2014 standards with

energy efficiency level

Off load tap changing range steps +2.5% to -5% on H.V

for variation should be provided. The H.V. shall be

connected Delta & Secondary with star connection. The

transformer should have cable-end boxes on H.T. side

suitable for up to 3 core 150 sq.mm. XLPE cable & on

L.T. side suitable for bus duct or cables as per requirement

complete with test certificates from manufacturers

1. Oil conservator with filling Hole & Cap - One No.

Thermometer pocket with 6" dial type thermometer switch

alarm & trip contacts- Two nos. 3. Silica-gel breather

with charge- One No. 4. Plain oil level gauge - One

197 No. 5. Drain / Sampling / Filter valve- One No. 6. Top 2.00 1606000.00 Nos.

Filter Valve - One No.

7. Explosion vent with Diaphragm - One No.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

7. Explosion vent with Diaphragm - One No.

Rating & Diagram plate - One No. 9. Additional

neutral bushing for earthing - One No. 10. Bi

directional Roller - Four Nos. 11. Earthing terminals -

Two Nos. 12. Lifting lugs - Two Nos. 13. Air release plug.

- One No. 14. Double float buchholz relay with Alarm

and trip contacts. 15. Control cable as required from

Transformer to VCB Panel is to be provided with

necessary connection to VCB relays for protection. as per

IS 1180 level-1

Note: Transformer shall be suitable for parallel operation.

Minimum requirement shall be as below:

Both transformer shall have " Identical X/R ratio, phase

angle shift, polarity, phase sequence, frequency, position

of tap changer. Turns ratio & voltage ratio"

DISTRIBUTION TRANSFORMER

SITC of outdoor type, three phase, oil immersed

distribution transformer of required KVA and voltage

ratio, copper double wound, vector group Dyn11, HV

delta connected and LV star connected with neutral

brought out to provide separate earthing terminals,

complete with bushing/cable box on HV side and cable

box on LV side suitable for cables or bus duct as per

requirement with standard fittings, conforming to IS:1180

(Part-1)/2014 with its latest amendments, including first

fill of transformer oil and accessories such as oil

conservator with filling holes, cap and prismatic oil level

gauge; silica gel dehydrating breather charged with silica

gel; oil drain cum sampling valve with plug; oil filter

valve; lifting eyes/hooks/lugs; two earthing terminals;

diagram and rating plate; air release plug; explosion vent

with diaphragm; thermometer pocket; four bi-directional

plain rollers with base channel with hauling holes;

fixed/separate type radiator banks; off-circuit externally

operated tapping switch (for rating <1000 kVA); 100 mm

stem type oil temperature indicator (for rating <500 kVA);

Buchholz relay with shut-off valve (for rating ≥500 kVA);

150 mm dial type oil temperature indicator with alarm/trip

contact (for rating ≥500 kVA); 150 mm dial type winding

temperature indicator with alarm/trip contact

(for rating ≥1000 kVA); marshalling box (for rating ≥500

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

(for rating ≥1000 kVA); marshalling box (for rating ≥500

kVA); 150 mm dia. magnetic type oil gauge (for rating

≥1600 kVA); inspection cover and jacking lugs (for rating

≥1600 kVA). For transformers having oil storage capacity

of 2000 liters and above, nitrogen injection fire protection

system (NIFPS) shall be provided.

(C) 400 KVA - Cat.III

Max. allowable loses at 50 % of rated load is 2.79 KW

and at full load is 7.77 KW

Note: Transformer shall be suitable for parallel operation.

Minimum requirement shall be as below:

Both transformer shall have " Identical X/R ratio, phase

angle shift, polarity, phase sequence, frequency, position

of tap changer. Turns ratio & voltage ratio"

Casting of transformer plinth / foundation including oil

soak pit (where required) in situ reinforced cement

concrete in M 20 using granite, quartzite trap metal of size

6 mm to 20 mm for RCC work including providing of

grade cement & Fe 415 grade TMT bars, scaffolding,

centering, form work, curing etc. complete.

Size:- 1250x1250x

Casting of transformer plinth / foundation including oil

soak pit (where required) in situ reinforced cement

concrete in M 20 using granite, quartzite trap metal of size

6 mm to 20 mm for RCC work including providing of

200 grade cement & Fe 415 grade TMT bars, scaffolding, 2.00 35000.00 Set

centering, form work, curing etc. complete.

Size:- 1500x1500x

Supply and levelling of Switch yard & transformer yard

using gravel, fine sand and other required filing material,

enmarked for the Switchyard & Transformer yard

including removing of trees or boulders etc. if any. The

general level of the yard shall be at a convenient level for

201 movement of man and material and it should match with 225.00 350.00 Sq.m.

FGL and as per Specification and Drg.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

Supply and Installation of GI Chain link fencing frames

with L angle/Channel post around Transformer yard etc. as

per Specification and Drg.

202 MPS-1 TO STP 180.00 1080.00 RMt.

SITC of 3.0 mtr wide gate with GI chain link as per

Specification and Drg.

MEDIUM VOLTAGE PANEL BOARD (PMCC)

SITC of PMCC Panel (50kA) complete in all respects as

per SLD / Specification / IS and including following as

(1) Two nos. FP 400A Microprocessor EDO ACB for I/C

with Digital Voltmeter with Voltmeter Selector Switch,

Digital Power Factor Meter, Digital Ammeter with

Ammeter selector switch, MFM with RS-485, R, Y, B, on,

off, trip Indicating lamps & ON, E-STOP, Reset

Pushbutton, etc.

(2) One no. FP 400A Thermal Magnetic EDO ACB for

(3) 400A TPN Main busbars. (Main & Auxilary bus-bars

size with current density 0.8A/Sq.mm)

(4) Three Nos. (2W + 1S) Soft Starter for min. 75 kW

Motor or higher as per pump Manufacturer reco. with

suitable derating and with 160A TPN Motor Duty MCCB,

160A AC3 duty line & external bypass contactor, Ten

channel temperature scanner with potential free contacts,

fast acting fuse, MFM with RS-485, door display key pad

& digital MPR+SPP with CBCT, on, off, trip Indicating

lamps & ON, E-STOP, Local/Remote, Auto/ Manual

selector switch & LCS for Pump- MOV Actuator with

Indication & push button etc.

204 (5) Tr. losses comp. fixed capacitor bank with Two 1.00 1881000.00 Set

nos. 5 kVAR capacitors bank each with capacitor duty

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

nos. 5 kVAR capacitors bank each with capacitor duty

contactor, timer & 'D' curve MCB, etc. for each

(6) Two nos. 160A FP Microprocessor MCCB feeder for

(7) Three nos. 63ATPN MCCB feeders (for 2 nos PDB -

Auxiliary accessories load, Spare)

(8) 2 no. 32A TPN MCCB spare.

(9) One no. Outdoor lighting LDB feeder with 32ATPN

'C' curve MCB with 32A contactor & Time switch.

(10) 4 nos. 32A 'C' curve MCB feeders (for Indoor LDB,

3nos. spare feeders)

(11) 4nos. 16A DP MCB feeders (for single phase supply

for 2nos. X'mer marshaling box, HT Panel & Spare.)

(12) 6nos. 400A/1A, Cl.-0.5 metering CT

(13) 2nos. 400A/1A, Cl.-1. APFC CT

(14) 2nos. Multiplication relay for dry run protection of

MEDIUM VOLTAGE PANEL BOARD (PMCC)

SITC of PMCC Panel (50kA) complete in all respects as

per SLD / Specification / IS and including following as

(1) Two nos. FP 400A Microprocessor EDO ACB for I/C

with Digital Voltmeter with Voltmeter Selector Switch,

Digital Power Factor Meter, Digital Ammeter with

Ammeter selector switch, MFM with RS-485, R, Y, B, on,

off, trip Indicating lamps & ON, E-STOP, Reset

Pushbutton, etc.

(2) One no. FP 400A Thermal Magnetic EDO ACB for

(3) 400A TPN Main busbars. (Main & Auxilary bus-bars

size with current density 0.8A/Sq.mm)

(4) Three Nos. (2W + 1S) Soft Starter for min. 55 kW

Motor or higher as per pump Manufacturer reco. with

suitable derating and with 160A TPN Motor Duty MCCB,

160A AC3 duty line & external bypass contactor, Ten

channel temperature scanner with potential free contacts,

fast acting fuse, MFM with RS-485, door display key pad

& digital MPR+SPP with CBCT, on, off, trip Indicating

lamps & ON, E-STOP, Local/Remote, Auto/ Manual

selector switch & LCS for Pump- MOV Actuator with

Indication & push button etc.

(5) Tr. losses comp. fixed capacitor bank with One nos.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

(5) Tr. losses comp. fixed capacitor bank with One nos.

kVAR Two nos. 5 kVAR capacitors bank each with

capacitor duty contactor, timer & 'D' curve MCB, etc. for

each transformer.

(6) Two nos. 160A FP Microprocessor MCCB feeder for

(7) Three nos. 63ATPN MCCB feeders (for 2 nos PDB -

Auxiliary accessories load, Spare)

(8) 2 no. 32A TPN MCCB spare.

(9) One no. Outdoor lighting LDB feeder with 32ATPN

'C' curve MCB with 32A contactor & Time switch.

(10) 4 nos. 32A 'C' curve MCB feeders (for Indoor LDB,

3nos. spare feeders)

(11) 4nos. 16A DP MCB feeders (for single phase supply

for 2nos. X'mer marshaling box, HT Panel & Spare.)

(12) 6nos. 400A/1A, Cl.-0.5 metering CT

(13) 2nos. 400A/1A, Cl.-1. APFC CT

(14) 2nos. Multiplication relay for dry run protection of

MEDIUM VOLTAGE PANEL BOARD (PMCC)

SITC of PMCC Panel (50kA) complete in all respects as

per SLD / Specification / IS and including following as

(1) Two nos. FP 800A Microprocessor EDO ACB for I/C

with Digital Voltmeter with Voltmeter Selector Switch,

Digital Power Factor Meter, Digital Ammeter with

Ammeter selector switch, MFM with RS-485, R, Y, B, on,

off, trip Indicating lamps & ON, E-STOP, Reset

Pushbutton, etc.

(2) One no. FP 400A Thermal Magnetic EDO ACB for

(3) 800A TPN Main busbars. (Main & Auxilary bus-bars

size with current density 0.8A/Sq.mm)

(4) Five Nos. (3W + 2S) Soft Starter for min. 75 kW

Motor or higher as per pump Manufacturer reco. with

suitable derating and with 160A TPN Motor Duty MCCB,

160A AC3 duty line & external bypass contactor, Ten

channel temperature scanner with potential free contacts,

fast acting fuse, MFM with RS-485, door display key pad

& digital MPR+SPP with CBCT, on, off, trip Indicating

lamps & ON, E-STOP, Local/Remote, Auto/ Manual

selector switch & LCS for Pump- MOV Actuator with

Indication & push button etc.

(5) Tr. losses comp. fixed capacitor bank with One

nos 20 kVAR, Two nos. 10 kVAR & Two nos. 5 kVAR

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

nos 20 kVAR, Two nos. 10 kVAR & Two nos. 5 kVAR

capacitors bank each with capacitor duty contactor, timer

& 'D' curve MCB, etc. for each transformer.

(6) Two nos. 200A FP Microprocessor MCCB feeder for

(7) Three nos. 63ATPN MCCB feeders (for 2 nos PDB -

Auxiliary accessories load, Spare)

(8) 2 no. 32A TPN MCCB spare.

(9) One no. Outdoor lighting LDB feeder with 32ATPN

'C' curve MCB with 32A contactor & Time switch.

(10) 4 nos. 32A 'C' curve MCB feeders (for Indoor LDB,

3nos. spare feeders)

(11) 4nos. 16A DP MCB feeders (for single phase supply

for 2nos. X'mer marshaling box, HT Panel & Spare.)

(12) 6nos. 800A/1A, Cl.-0.5 metering CT

(13) 2nos. 800A/1A, Cl.-1. APFC CT

(14) 2nos. Multiplication relay for dry run protection of

LV POWER CONTROL CENTER (PCC)

Supply, installation, testing and commissioning of LV

Distribution Board (LVDB), totally enclosed, dust- and

vermin-proof, indoor type, fabricated from CRCA sheet

steel with minimum thickness of 3.0 mm for base frame,

channels and gland plates, 2.0 mm for load-bearing

members and doors, and 1.6 mm for internal partitions,

with a minimum degree of protection of IP-52 as per IS:

2147. The LVDB shall be suitable for operation on 3-

phase, 4-wire, 415 V, 50 Hz system with effectively

grounded neutral. The panel shall be provided with

instrumentation compartments accommodating meters,

auxiliary and protective relays, LED type indicating lamps

and control MCBs conforming to IS: 13947. Current

transformers and voltage transformers shall conform to IS:

2705. The panel shall be provided with air-insulated

electrolytic grade aluminium / copper bus bars for three-

phase and neutral system, along with GI earth bus

extending throughout the entire length of the panel. Power

and control wiring shall be carried out using 1100 V

grade, FRLS insulated copper conductor wires conforming

to IS: 694 and IS: 8130, complete with all necessary

equipment fittings. The LVDB shall have a horizontally

running busbar compartment with a minimum height of

300 mm. Incoming and outgoing cable connections

shall be suitable for 1100 V grade aluminium / copper

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

shall be suitable for 1100 V grade aluminium / copper

conductor, XLPE / PVC insulated and PVC sheathed

armoured cables. The LVDB shall be provided with the

required incoming, bus coupler and outgoing modules of

the specified type and ratings.

Above 80 A, upto & including 250 A, 3 & 4 Pole, Air

Break Fixed MCCB conforms to IS / IEC 60947-2 with

trip free mechanism, current limiting type with Thermal-

Magnetic / Microprocessor release (O / C, S / C & E / F)

with adjustable settings & having minimum 2NO+2NC

potential free auxiliary contacts with all necessary Electro-

Mechanical protections & interlocks etc. MCCB module,

when used as Incommer / Bus Coupler, shall have

enclosure dimensions- 1800(H) x 600(W) x 600 (D) &

following technical features:

4 Pole, 160A MCCB with Breaking Capacity of Icu=50

KA at 415V (Ics =100% of Icu), Microprocessor release

MPS TO KARAI NETWORK

MEDIUM VOLTAGE PANEL BOARD (PMCC)

SITC of PMCC Panel (50kA) complete in all respects as

per SLD / Specification / IS and including following as

(1) One nos. FP 160A Microprocessor EDO MCB for I/C

with Digital Voltmeter with Voltmeter Selector Switch,

Digital Power Factor Meter, Digital Ammeter with

Ammeter selector switch, MFM with RS-485, R, Y, B, on,

off, trip Indicating lamps & ON, E-STOP, Reset

Pushbutton, etc.

(2) 200A TPN Main busbars. (Main & Auxilary bus-bars

size with current density 0.8A/Sq.mm)

(3) Two Nos. (1W + 1S) Soft Starter for min. 30 kW

Motor or higher as per pump Manufacturer reco. with

suitable derating and with 80A TPN Motor Duty MCCB,

80A AC3 duty line & external bypass contactor, Ten

channel temperature scanner with potential free contacts,

fast acting fuse, MFM with RS-485, door display key pad

& digital MPR+SPP with CBCT, on, off, trip Indicating

208 lamps & ON, E-STOP, Local/Remote, Auto/ Manual 1.00 1122000.00 Set

selector switch & LCS for Pump- MOV Actuator with

Indication & push button etc.

(4) Two nos. 40A FP Microprocessor MCCB feeder for

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

(5) Two nos. 63ATPN MCCB feeders (for 1 nos PDB -

Auxiliary accessories load, Spare)

(6) 2 no. 32A TPN MCCB spare.

(7) One no. Outdoor lighting LDB feeder with 32ATPN

'C' curve MCB with 32A contactor & Time switch.

(8) 3 nos. 32A 'C' curve MCB feeders (for Indoor LDB,

2nos. spare feeders)

(9) 4nos. 16A DP MCB feeders (for Spare.)

(10) 3nos. 200A/1A, Cl.-0.5 metering CT

(11) 3nos. 200A/1A, Cl.-1. APFC CT

(12) 2nos. Multiplication relay for dry run protection of

MPS TO KARAI NETWORK

Design, supplying, installing, and testing of a factory-

fabricated, ready-made Three Phase APFC Panel. The

cubical panel fabrication shall be type-tested as per IEC

61921 and IEC 61439:1 & 2. Capacitor duty contactors

shall be provided for switching as per the required steps.

The incomer switch shall be of MCCB type with Icu = Ics

= 50 kA at 400/440 volts and shall include overcurrent

(OC), short-circuit (SC), and internal earth fault

protection. The panel shall include copper tinned insulated

busbars and shall be an indoor type cubical panel with

IP43 and IK10 protection. It shall be equipped with

metalized polypropylene film-type 3-phase 550-volt

capacitors and a detuning reactor for each capacitor. The

panel shall have short-circuit and overload protection, and

each capacitor step shall include a suitable MCB with SC,

OL, and internal earth fault relay. Each stage shall be

provided with a stage contactor (capacitor load rating).

The power factor (PF) regulator master controller shall

have suitable steps with an LCD display and an RS-485

communication port. Indication LED lamps shall be

provided for the main incomer and for ON/OFF status of

each capacitor bank. The panel shall include an MS

channel for floor mounting, cable entry as per site

conditions, and cooling fans for proper ventilation.

95 KVAR capacity: APFC panel consisting following

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

(1) 160 A FP Microprocessor MCCB I/C.

(2) 5 Steps Microprocessor APFC Relay with sensitivity

(3) 1 no. 30 kVAR capacitor bank with 63A 'D' curve

MCB & 30 kVAR Capacitor duty contactor with timer.

(4) 1 no. 20 kVAR capacitor bank with 40A 'D' curve

MCB & 20 kVAR Capacitor duty contactor with timer.

(5) 3 nos. 10 kVAR capacitor bank with 20A 'D' curve

MCB & 10 kVAR Capacitor duty contactor with timer.

(6) 3 nos. 5 kVAR capacitor bank with 16A 'D' curve

MCB & 5 kVAR Capacitor duty contactor with timer.

(7) All capacitors shall be Gas Filled type with dielectric

losses ≤ 0.2w/kVAR.

(Suitable for 0.95 or better Correction).

Design, supplying, installing, and testing of a factory-

fabricated, ready-made Three Phase APFC Panel. The

cubical panel fabrication shall be type-tested as per IEC

61921 and IEC 61439:1 & 2. Capacitor duty contactors

shall be provided for switching as per the required steps.

The incomer switch shall be of MCCB type with Icu = Ics

= 50 kA at 400/440 volts and shall include overcurrent

(OC), short-circuit (SC), and internal earth fault

protection. The panel shall include copper tinned insulated

busbars and shall be an indoor type cubical panel with

IP43 and IK10 protection. It shall be equipped with

metalized polypropylene film-type 3-phase 550-volt

capacitors and a detuning reactor for each capacitor. The

panel shall have short-circuit and overload protection, and

each capacitor step shall include a suitable MCB with SC,

OL, and internal earth fault relay. Each stage shall be

provided with a stage contactor (capacitor load rating).

The power factor (PF) regulator master controller shall

have suitable steps with an LCD display and an RS-485

communication port. Indication LED lamps shall be

provided for the main incomer and for ON/OFF status of

each capacitor bank. The panel shall include an MS

channel for floor mounting, cable entry as per site

conditions, and cooling fans for proper ventilation.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

75 KVAR capacity: APFC panel consisting following

(1) 160 A FP Microprocessor MCCB I/C.

(2) 8 Steps Microprocessor APFC Relay with sensitivity

(3) 1 no. 30 kVAR capacitor bank with 63A 'D' curve

MCB & 30 kVAR Capacitor duty contactor with timer.

(4) 1 no. 20 kVAR capacitor bank with 40A 'D' curve

MCB & 20 kVAR Capacitor duty contactor with timer.

(5) 1 nos. 10 kVAR capacitor bank with 20A 'D' curve

MCB & 10 kVAR Capacitor duty contactor with timer.

(6) 3 nos. 5 kVAR capacitor bank with 16A 'D' curve

MCB & 5 kVAR Capacitor duty contactor with timer.

(7) All capacitors shall be Gas Filled type with dielectric

losses ≤ 0.2w/kVAR.

(Suitable for 0.95 or better Correction).

Design, supplying, installing, and testing of a factory-

fabricated, ready-made Three Phase APFC Panel. The

cubical panel fabrication shall be type-tested as per IEC

61921 and IEC 61439:1 & 2. Capacitor duty contactors

shall be provided for switching as per the required steps.

The incomer switch shall be of MCCB type with Icu = Ics

= 50 kA at 400/440 volts and shall include overcurrent

(OC), short-circuit (SC), and internal earth fault

protection. The panel shall include copper tinned insulated

busbars and shall be an indoor type cubical panel with

IP43 and IK10 protection. It shall be equipped with

metalized polypropylene film-type 3-phase 550-volt

capacitors and a detuning reactor for each capacitor. The

panel shall have short-circuit and overload protection, and

each capacitor step shall include a suitable MCB with SC,

OL, and internal earth fault relay. Each stage shall be

provided with a stage contactor (capacitor load rating).

The power factor (PF) regulator master controller shall

have suitable steps with an LCD display and an RS-485

communication port. Indication LED lamps shall be

provided for the main incomer and for ON/OFF status of

each capacitor bank. The panel shall include an MS

channel for floor mounting, cable entry as per site

conditions, and cooling fans for proper ventilation.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

135 KVAR capacity: APFC panel consisting following

(1) 160 A FP Microprocessor MCCB I/C.

(2) 5 Steps Microprocessor APFC Relay with sensitivity

(3) 2 no. 30 kVAR capacitor bank with 63A 'D' curve

MCB & 30 kVAR Capacitor duty contactor with timer.

(4) 2 no. 20 kVAR capacitor bank with 40A 'D' curve

MCB & 20 kVAR Capacitor duty contactor with timer.

(5) 2 nos. 10 kVAR capacitor bank with 20A 'D' curve

MCB & 10 kVAR Capacitor duty contactor with timer.

(6) 3 nos. 5 kVAR capacitor bank with 16A 'D' curve

MCB & 5 kVAR Capacitor duty contactor with timer.

(7) All capacitors shall be Gas Filled type with dielectric

losses ≤ 0.2w/kVAR.

(Suitable for 0.95 or better Correction).

Design, supplying, installing, and testing of a factory-

fabricated, ready-made Three Phase APFC Panel. The

cubical panel fabrication shall be type-tested as per IEC

61921 and IEC 61439:1 & 2. Capacitor duty contactors

shall be provided for switching as per the required steps.

The incomer switch shall be of MCCB type with Icu = Ics

= 50 kA at 400/440 volts and shall include overcurrent

(OC), short-circuit (SC), and internal earth fault

protection. The panel shall include copper tinned insulated

busbars and shall be an indoor type cubical panel with

IP43 and IK10 protection. It shall be equipped with

metalized polypropylene film-type 3-phase 550-volt

capacitors and a detuning reactor for each capacitor. The

panel shall have short-circuit and overload protection, and

each capacitor step shall include a suitable MCB with SC,

OL, and internal earth fault relay. Each stage shall be

provided with a stage contactor (capacitor load rating).

The power factor (PF) regulator master controller shall

have suitable steps with an LCD display and an RS-485

212 communication port. Indication LED lamps shall be 2.00 141586.33 Set

provided for the main incomer and for ON/OFF status of

each capacitor bank. The panel shall include an MS

channel for floor mounting, cable entry as per site

conditions, and cooling fans for proper ventilation.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

25 KVAR capacity: APFC panel consisting following

(1) 40 A FP Microprocessor MCCB I/C.

(2) 5 Steps Microprocessor APFC Relay with sensitivity

(3) 5 nos. 5 kVAR capacitor bank with 16A 'D' curve

MCB & 5 kVAR Capacitor duty contactor with timer.

(4) All capacitors shall be Gas Filled type with dielectric

losses ≤ 0.2w/kVAR.

(Suitable for 0.95 or better Correction).

MPS TO KARAI NETWORK

SITC of Power Distribution Board (PDB) for MOV as

3 Phase 4 Wire TPN, 8 way Prewired LDB cum PDB for

Actuators and EOT and Aux. load.

Incoming: 63A TPN, MCB 'C' Curve

Outgoing: 6 nos. 6-32A TP MCB 'C' Curve

MPS TO KARAI NETWORK

SITC of Light Distribution Board (LDB) as under: (For

Indoor Lighting & Outdoor Lighting)

3 Phase 4 Wire TPN, 8 way Prewired LDB for Lighting

Incoming: 63A TPN, MCB 'C' Curve

Outgoing: 6 nos. 6-32A TP MCB 'B' Curve

MPS TO KARAI NETWORK

MEDIUM VOLTAGE CABLES

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium / Copper conductor for

KV. to be laid on wall with necessary clamps or in existing

trench / pipe of following size of cables

3.5C x 185 sq. mm. A2XFY Cable (2Run for Transformer-

1 & 2 to LT Panel)

3.5C x 70 sq. mm. A2XFY Cable (1Run for APFC)

3C x 95 sq. mm. A2XFY Cable (1Run each for each

Motor) 180.00 420.28 Mtr.

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

MEDIUM VOLTAGE CABLES

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium / Copper conductor for

KV. to be laid on wall with necessary clamps or in existing

trench / pipe of following size of cables

3.5C x 120 sq. mm. A2XFY Cable (2Run for Transformer-

1 & 2 to LT Panel)

3.5C x 70 sq. mm. A2XFY Cable (1Run for APFC)

3C x 95 sq. mm. A2XFY Cable (1Run each for each

Motor) 180.00 420.28 Mtr.

MEDIUM VOLTAGE CABLES

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium / Copper conductor for

KV. to be laid on wall with necessary clamps or in existing

trench / pipe of following size of cables

3.5C x 300 sq. mm. A2XFY Cable (3Run for Transformer-

1 & 2 to LT Panel)

3.5C x 185 sq. mm. A2XFY Cable (1Run for APFC

3C x 95 sq. mm. A2XFY Cable (1Run each for each

Motor) 300.00 420.28 Mtr.

MEDIUM VOLTAGE CABLES

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium / Copper conductor for

KV. to be laid on wall with necessary clamps or in existing

trench / pipe of following size of cables

3.5C x 95 sq. mm. A2XFY Cable (1 Run Incomer Panel to

MPS TO KARAI NETWORK

4C x 16 sq. mm. A2XFY Cable (1Run for APFC)

MPS TO KARAI NETWORK

3C x 35 sq. mm. A2XFY Cable (1Run each for each

Motor) 60.00 189.14 Mtr.

MPS TO KARAI NETWORK

4C x 6 sq. mm. A2XFY Cable (For Outdoor LDB, Indoor

MPS TO KARAI NETWORK

4C x 2.5 sq. mm. 2XWY/2XFY Cu Cable (For Motor

Operated Valves)

MPS TO KARAI NETWORK

Sr. No. Description Qty. Rate (Rs.) Unit Amount (Rs.)

3C x 2.5 sq. mm. 2XWY/2XFY Cable (For Outdoor light /

MPS TO KARAI NETWORK

2C x 2.5 sq. mm. 2XWY/2XFY Cu Cable (For 5 Nos.

Motor space heater (as required)), HT Panel, for 2nos.

APFC CT & X'mer marshaling box Single Phase Supply,

for level switch)

MPS TO KARAI NETWORK

10C x 1.5 sq.mm. 2XWY/2XFY Cable (2Run Tr. to HT

Panel control cable)