Renovation of Swarnim Sanskrutik Kendra at Raysan for Gandhinagar Municipal Corporation (Re-invite)

Name of work : Renovation of Swarnim Sanskrutik Kendra at Raysan in Gandhinagar Municipal Corporation.

No. Item Description Unit Total Qty Rate in Words Total Amount

No. Item Description Unit Total Qty Rate in Words Total Amount

Excavation for foundation upto 1.5 m depth including Rupees One

sorting out and stacking of useful materials and disposing Hundred

1 off the excavated stuff upto 50 Meter lead.(A) Loose or soft Cu.Mt. 42.00 123.13 Twenty Three

Excavation for foundation for depth from 1.5 m to 3.0 m

including sorting out and stacking of useful materials and

2 disposing off the excavated stuff upto 50 Meter lead.(A) Cu.Mt. 34.00 136.30

Loose or soft soil

Providing and laying cement concrete 1:2:4 (1- Cement : 2-

Coarse sand : 4- graded stone aggregates 20 mm nominal

size) and curing complete excluding cost of formwork in (A)

Foundation and Plinth

3 Cu.Mt. 7.00 3758.19 Hundred Fifty

Eight and Paise

Providing and laying controlled cement concrete work M250

and curing complete including the cost of form work but

excluding reinforcement of reinforced concrete work in : (A)

4 Cu.Mt. 2.00 4402.59 Hundred Two

foundation, footing, base of columns and mass concrete

and Paise Fifty

Providing and laying controlled cement concrete work M250

and curing complete including the cost of form work but Rupees Four

excluding reinforcement of reinforced concrete work in : (A) Thousand Seven

5 foundation, footing, base of columns and mass concrete Cu.Mt. 6.00 4711.00 Hundred Eleven

Providing and laying controlled cement concrete M250 and

curing complete including the cost of form work but

excluding reinforcement of reinforced concrete work in (C)

6 Cu.Mt. 1.00 5989.30 Hundred Eighty

Beams, Girders and Cantilever upto floor two level.

Providing and laying controlled cement concrete work M250

and curing complete including the cost of form work but Rupees Six

excluding reinforcement of reinforced concrete work in : Thousand Seven

Wall (Pardi) up to floor two level Hundred

and Paise Sixty

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine

8 Cu.Mt. 2.00 4214.09 Hundred

sand)(B) Conventional

Paise Nine Only

Filling available excavated earth (excluding rock in trenches Rupees One

plinth, sides of foundations etc. in layers not exceeding 20 Hundred Thirty

9 cm. in depth consolidating each deposited layer by ramming Cu.Mt. 13.00 136.92 Six and Paise

and watering) Ninety Two

Filling in foundation and plinth with murrum or selected soil

in layers of 20cm. thickness including watering, ramming Rupees Two

and consolidating etc. complete. Hundred

10 Cu.Mt. 1.00 277.14 Seventy Seven

Carring out plinth treatment to post construction / existing

structure by spraying chemical solution for termite control

treatment including labour and material consistment with

I.S.I specification. Using Chlordene and Chiorpurfiles 20 EC. Rupees One

As Per 6131_paret-II Consentration Weight one percent is Hundred Eleven

11 recommended i.e one litre 20 EC chemical emulsion with 19 Sq.Mt. 5.00 111.25 and Paise

liter give 1 % concrentration inclusive of one litre chemical Twenty Five

emulsion appication at the rate of 5 Litre chemical / Sqm of Only

surface is recommended as per I.S

Providing and laying controlled cement concrete work M250 Rupees Three

and curing complete including the cost of form work but Thousand Nine

excluding reinforcement of reinforced concrete work in: (A) Hundred

Grade slab Seventy and

Paise Fifty Nine

Providing and laying controlled cement concrete work M250

and curing complete including the cost of form work but

excluding reinforcement of reinforced concrete work UP TO

13 FLOOR TWO LEVEL : A1)COLUMN At Ground Floor Level Cu.Mt. 2.00 7892.72

Providing and laying controlled cement concrete M250 and

curing complete including the cost of form work but

excluding reinforcement of reinforced concrete work in:

14 Cu.Mt. 1.00 6742.06 Hundred Forty

Beam At Ground Floor Slab

Providing and laying controlled cement concrete M250 and

curing complete including the cost of form work but

excluding reinforcement of reinforced concrete work in :

15 Cu.Mt. 1.00 6412.10 Hundred Twelve

Slab At Ground Floor Slab

Providing and laying controlled cement concrete M250 and

curing complete including the cost of form work but Rupees Seven

excluding reinforcement of reinforced concrete work in :D) Thousand Seven

16 Lintel at Ground floor Cu.Mt. 1.00 7760.84 Hundred Sixty

and Paise Eighty

Providing and laying controlled cement concrete M250 and

curing complete including the cost of form work but

excluding reinforcement of reinforced concrete work in :E)

17 IN Chhajja at Ground floor Cu.Mt. 1.00 6623.58

and Paise Fifty

Providing IS mark TMT Bar FE 500/500D reinforcement for

R.C.C. work including bending, binding and placing in

Seven and Paise

18 position complete upto floor two level. Kg. 4865.00 77.29

Masonary work using Aerated light weight concrete block

having crushing strength not less than 35 kg/sqcm for super Rupees Five

structure above plinth level upto floor two level using Thousand Three

Polymer modified adhesive mortar complete as per Hundred

Technical Specification & direction of Engineer in charge. Seventeen and

(Ground floor) Paise Sixty Five

Masonary work using Aerated light weight concrete block

having crushing strength not less than 35 kg/sqcm for super

structure above plinth level using Polymer modified

20 Cu.Mt. 1.00 5360.07 Hundred Sixty

adhesive mortar complete as per Technical Specification &

and Paise Seven

direction of Engineer in charge (First floor)

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for interior

21 plastering upto floor two level and finished even and Sq.Mt. 23.00 165.02

smooth in (ii) Cement mortar 1:4 (1-cement :4-sand) At

Providing and applying 10mm. thick cement plaster in single

coat on ceiling for interior plastering upto floor two level

22 and finished even and smooth in (i) cement mortar 1:3 (1 Sq.Mt. 8.00 148.00

Eight and Paise

cement : 3 sand ) at Ground Floor

20mm thick sand faced cement plaster on walls above

ground level consisting of 12mm thick backing coat of C.M.

Hundred Fifteen

23 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of C.M. Sq.Mt. 61.00 315.69

and Paise Sixty

1:1 (1-cement : 1-sand) etc. complete.For All Floors.

Providing and fixing 150 mm wide, approved quality chicken

wire mesh at junction of brick work and RCC work or two

dissimilar surfaces, at all heights fixed by nails, rowal plugs

24 Sq.Mt. 54.00 58.58 Eight and Paise

or tag by cement mortar 1:3 before applying the plaster,

Fifty Eight Only

including curing, scaffolding all complete as directed.

Providing 20 mm deep finished groove in plaster in line and

level etc. Comp. For all Floor

Seven and Paise

Providing throating or plaster drip and moulding to RCC Rupees Forty

Chhajja Three and Paise

Providing cement vata ( 10 cm x 10 cm size ) quarter round

in cement mortar 1:1 including neat cement finishing,

27 watering etc. complete Rmt. 11.55 24.28

Applying two coats of putty & two coats of primer of

approved brand and manufacture on new wall surface to Rupees Forty

28 give an even shade including thoroughly brushing the Sq.Mt. 92.00 40.59 and Paise Fifty

surface free from mortar dropping and other foreign matter Nine Only

and sand papered smooth.

Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall

surface to give an even shade including throughly brushing

29 Sq.Mt. 23.00 83.18 Three and Paise

the surface free from mortar droppings and other foreign

matter and sand papered smooth.For All Floors.

Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on ceiling and slopping Rupees Eighty

roofs to give an even shade including throughly brushing the Eight and Paise

surface free from mortar droppings and other foreign Eighty Seven

matter and sand papered smooth.For All Floors. Only

Finising wall with weatherproof exterior emulsion paint on

wall surface (two coats) to give and required shape even

shade after thoroughly brushing the surface to remove all

31 Sq.Mt. 795.00 120.26 Twenty and

dirts , and remains of ioose powdered materials etc.

complete. two Coats of primer has to be applied.

Providing & applying single coat of textured at external

surface at all floor levels with three coats of weather proof

cement exterior paint of approved standard brands make

(Asian/Dulux/Narolac) at outer side of the building on RCC

or Masonary walls. Rate to include for all labour, materials,

staging, scaffolding, cleaing, curing etc. application of Rupees Six

texture after throughly brushing th`e surface to give an Hundred

32 even shade free from mortar dropping/other foreign matter Sq.Mt. 142.00 624.89 Twenty Four

etc. complete. application of textures & paints must be as and Paise Eighty

per company's standard instructions. Texture and colour Nine Only

selection as per approved by engineer in charge.(It is

recommended to use low voc paints rated by IGBC)

Providing & laying 24"x24" Vitrified tiles 8 MM thick in

flooring over 20 mm (Av.) base of C.M. 1:6 (1 Cement : 6 Rupees One

Coarse sand ) on new surface or fixing on existing flooring Thousand Three

by adhesive materials incldg. Dismanteling of existing Hundred Thirty

flooring & joined with colour cement slurry including One and Paise

finished with flush pointing & cleaning the surface etc. Twenty Two

completed Light Shade. Only

Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x

24'' in skrting risers of steps and dedo on 10mm thick

cement plaster 1:3 (1-cement : 3-coarse sand) and jointed

34 Sq.Mt. 1.00 1114.09 Hundred

with white cement slurry

Paise Nine Only

Providing & laying 600mm x 600mm Matt Vitrified tiles of

to 10mm thick in skirting,riser of steps & dedo laid on bed

of 10 mm (Average) base of cement mortar 1:3 (1 Cement :

35 3 Coarse sand) thick & jointed with white cement slurry etc. Sq.Mt. 1143.00 1404.91

complete as per approvel & selection by architect/engineer

Providing and laying polished granite stone slab 18 mm thick Rupees Two

in skirting,sill and jambs,risers of steps, dedo and pllars laid Thousand Nine

on 10 mm thick cement mortar 1:3 (1 cement : 3 coarse Hundred Fifty

sand) and jointed with gray cement slurry including rubbing Eight and Paise

& polishing etc. Complete Twenty Nine

Providing and laying polished kota stone slab 25mm thick in Rupees One

risers of steps,skirting Dedo and pillars laid on 10mm thick Thousand Two

cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed Hundred

with gray cement slury mixed with pigment to match the Twenty Six and

shade of slab including rubbing and polishing etc. complete. Paise Forty Six

Providing and laying polished Kota stone slab flooring over

20mm (Average) thick base of cement mortar 1:6 (1-cement Rupees One

: 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse Thousand

38 sand) laid over and jointed with grey cement slurry mixed Sq.Mt. 2030.00 1019.39 Nineteen and

with pigment to match the shade of slab including rubbing Paise Thirty

and polishing etc. complete.(A) 25mm thick At All floors Nine Only

Supply & Fixing of Broken Glazed (China Mosaic) tiles size 5-

6 mm thick of different size and shade (approved crazy

patern) in Cement:Mortar 1:2 and joint filling with White

39 Sq.Mt. 4.00 779.70 Seventy Nine

Cement / Coloured Cement with water proofing component

including Ramping, Watering, Curing etc. complete (FOR ALL

Providing and laying integral cement based water proofing treatment

including preparation of surface as required for treatment of roofs,

balconies, terraces etc. consisting of following operations.(a) Applying and

grouting a slurry coat of neat cement using 2.75 kg/ sqm of cement

admixed with proprietary water proofing compound conforming to IS :

2645 over the R.C.C. slab including cleaing the surface before

treatment.(b) Laying cement conctrete using broken bricks\brick bats

mm to 100 mm size with 50 % of cement motar 1:5 ( 1 Cement : 5 Coarse

sand ) admixed with proprietory water proofing compound confiroming to

IS : 2645 over 20 mm thick layer of cemnt mortar of mix 1: 5 (1 cement :

Coarse sand ) admixed with proprietary water proofing compound

confirming to IS : 2645 to required slope adn treating similarly the

adjoining walls upto 300 m height inclusing rouding of juction of walls and Rupees Six

slabs.(C)After tow days of proper curing appling a second coat of cement Hundred Ninety

40 slurry admixed with proprietary water proofing compound I.S.2645 (d) Sq.Mt. 4.00 696.90

Finishing the surface with 20 mm thick jointless cement mortor of mix 1:4

admixed with proprietary water proofing compound I.S.2645 and finishing Ninety Only

the surface with trowel with neat cement slurry & making of (300 x

300)mm square (e)The whole terrace so finish shall be flooded with

water for a min. period of two weeks for curing and for final test. All

above operation to be down in order and as directed and specified by the

engi.-in-charge. With average thickness of 120 mm and minmum thickness

at khurra as 65mmCementconsumption 0.642 Bags / S.M.)

Providing and fixing 35 mm thick solid core flush door

shutter of approved make both side lamination using

1mm thick approved laminate sheets with 6mm thk

Lipping/border patti around flush hutter including fixing SS

hinges, with 5 mm float glass of 300 x 300 mm for viewing

AS PER REQUIREMENT, wedges, keys, nails, catch screw,

lever latches , handle(10 cm), aldrop(20 cms), stoppers(20

41 cms), etc and cutting/ drilling of necessary holes in Sq.Mt. 4.00 2578.53

masonry/ concrete and all as per drawing, specification

and Paise Fifty

and direction of the Engineer, all materials, tools,plant and

labour complete c. (All fixtures & fittings shall be

stainless steel of approved quality).approved by

architect/Engineer Incharge.At all Floors

Providing and fixing window having extruded Aluminium

colour anodized Section Frame main Outer Size 63.5mm x

38.1mm x 1.95mm( of Jindal Section No. 4605 @ Wt. of

1.094 Kg./Mt.) Horozontal Two track member size 61.85mm

x 31.75mm x 1.20mm(of Jindal Section No. 8687, @ Wt.

0.695Kg./Mt.) Vertical Member of size 61.85mm x 31.75mm

x 1.30mm (of Jindal Section No. 8758, @ Wt. 0.659 Kg./Mt.)

with sliding shutters of Horizontal member size 40mm x

42 18mm x 1.29mm(of Jindal Section No. 8947 @ Wt. of 0.456 Sq.Mt. 4.00 1713.70

Kg./Mt.) Vertical Member of size 40mm x 15mm x 1.29mm

(of Jindal Section No. 8948 @ Wt. of 0.457 Kg./Mt.) with

5mm thick transparent bronze colour tinted float glass with

powder coated Aluminium fittings & fixtures & trasparent

silicon sealant glass fixing to frame as per detail etc.

Providing and fixing fully fixed stainless grill using 50mm x

8mm (SS 304) stainless steel flats vertical 50mm X 8 mm Rupees Four

stainless steel lats horizontal,16 mm diameter rounnd Thousand Three

43 stainess steel bar at 120 mm center to center fixedto Sq.Mt. 4.00 4347.04 Hundred Forty

S.S.flats necessary S.S screws and other S.S fittings Seven and Paise

etc.complete. Four Only

Providing and fixing G.I. Rain water spout of 50mm dia. and Rupees One

30cm. length. Hundred One

44 No. 2.00 101.91 and Paise

Removing and scraping of old deteriorated plaster of any

thickness fromm wall/R.C.C member including stacking of Rupees Twenty

45 service able material and disposal of unserviceable from site SQ.MT 1440.00 20.55 and Paise Fifty

of work with all lead and lift. Five Only

Dismentaling tiled of stone floors laid in mortar including

stacking of serviceable materilas and disposal of Rupees Fifty

46 unserviceable materials with all lead and lift. SQ.MT 4287.00 50.11 and Paise

Providing and fixing Stainless Steel railing having 50 mm

x16G ASIS 304 Grade dia hollow stainless steel pipe as hand

rail and 32x32 mmx16G ASIS 304 Grade sq. hollow stainless

steel pipe with combination of 10 cm long 16 mmx16G ASIS

304 Grade dia pipe as vertical supports 16 mm x16G ASIS Rupees Five

304 Grade dia hollow stainless steel pipes as intermediate Thousand Three

47 members running through stainless steel 30 mm dia solid SQ.MT 75.00 5394.41 Hundred Ninety

runners having threaded screw to fix the runner with Four and Paise

vertical suppoet including cutting bending w=elding & Forty One Only

fabrication the structure as per drawing including finishing

Supply and Fabrication,Erection of M.S. Box section with

one coat of primer as per Approved Structural Drawings /

working Drawings given by Your Structural Engineer.

With Supply and Installation of 10mm thick 4 Layer Rupees Eight

Multiwall polycarbonate standing seam roofing sheet with Thousand Six

required accessories. Hundred

Sheet length : 15 Mtr as required. Twenty Four

Make. COXWELL/DPI and Paise Thirty

Colour: ICE Nine Only

GYPSUM CEILING Supplying and Fixing of Suspended ceiling

system components which includes Single Layer Boarding

with 12.5mm thick USG Boral Standard Plasterboard This

includes of USG Boral Thundersteel Perimeter Channel

(0.50mm thick having one flange of 20mm and another

flange of 30mm and a web of 28mm) screw fixed to brick

wall/partition with the help of approved screws at 600mm

centers. Then suspending of USG Boral Thundersteel

Intermediate channel (45mm x 0.90mm thick with two

flanges of 15mm each) from the soffit at 1220mm centers

with of USG Boral Thundersteel Ceiling Angle

(25x10mmx0.50mm thick) fixed to RCC Slab with of USG

Boral Soffit Cleat (37x27x25x1.6mm thick) and 8mm dia

40mm long Anchor Fastener @ 600mm Centers,

respectively. USG Boral Thundersteel Ceiling Section (having

web of 51 mm and two flanges of 27mm each) are then

fixed to the of USG Boral Thundersteel Intermediate

channel with the help of connecting clip (2.6mm Dia) and in

perpendicular direction to the USG Boral Thundersteel

intermediate channel at 457mm centers. USG Boral Rupees Eight

49 Thundersteel profiles are rolled with AZ Steel (150 GSM & SqM 954.0521 862.34406

310 MPa Yield Strength) having base metal conforming to IS Two and Paise

513:2016 as per IS 15961:2017/ AS 1397:2001).12.5mm Thirty Four Only

thick USG Boral Standard Plasterboards (confirming to IS

2095 Part 1) is screw fixed with 25mm long Drywall screws

at 230 mm centers. The screw fixing of gypsum boards to

the metal framing at the periphery, openings and cut edges

should be at 150mm centers.All the Gypsum boards must be

staggered. All joints to be taped & finished with USGBORAL

Paper tape & All-Purpose Joint Compound confirming to

ASTM C475. Material certificate to be provided by company.

and approved surface design in suspended grid with all

material, making of coves for indirect lighting

,grooves,cutting and labour,scaffolding, and as per

instruction of engineer and as per detailed drawing & image

as directed by the Architect and as approved by the

the metal framing at the periphery, openings and cut edges

should be at 150mm centers.All the Gypsum boards must be

staggered. All joints to be taped & finished with USGBORAL

Paper tape & All-Purpose Joint Compound confirming to

ASTM C475. Material certificate to be provided by company.

and approved surface design in suspended grid with all

material, making of coves for indirect lighting

,grooves,cutting and labour,scaffolding, and as per

instruction of engineer and as per detailed drawing & image

as directed by the Architect and as approved by the

Engineer in Charge.

SLETO WOODEN ACOUSTIC PANEL FOR CEILING-Providing

and fixing ceiling acoustical paneling Fixing with Sound Strut

screw fixed horizontal/vertical to wall at every 600mm c/c.

Metal cleat can be fixed on top edges of Sound Strut Ceiling

Section 55 fixed directly by stamping to the CS55 and

Intermediate Channel-91 which is screw fixed directly to the

wall where ever required and using Rock wool between

framing and panel with technical specification of 50 Kg

Density and 50MM thick glass wool and above CS55

fixing aluminum / GI channel with clip and fixing ecotone

Sleto Acoustic Panel make Sleto EPD2 10-10 or as per

selection as per architect of size 1200mmx2400mmx16mm

thick up to 2400mm high as per the following specification :-

Sleto EPD2 10-10 - 10mm hole with 10mm gap and center Rupees Four

to center distance of 110MM in equal stagger manner, 1200 Thousand Six

50 x 2400 x 16mm high grade MDF wood base Medium Density SqM 1.00 4691.45 Hundred Ninety

Fiber acoustic boards with Tongue & Groove Edge,2mm slot One and Paise

perforation @ 16mm centre, slates perforations, The Forty Five Only

acoustic shouldbe furnished with a Black absorbent felt

backing with an airflow resistance of 330-460 Ns/m³ (DIN

53887),wood practical core,NRC :should be Up to

0.75,should meet the safety requirements of EN14190. The

colour of panel as approved by Architect and as specified

and complete with all material, making of coves and cutouts

for ac grills ,labour & scaffolding with all lead, lift and

transport. and finished and complete the work satisfactorily

as per instruction of architect or Engineer-in charge.,

material & labour complete as directed by Architect /

Engineer – in – charge. BRAND

(AMAZON,ARMSTRONG,ECOTONE) BASIC RATE 375 SQFT

INCLUDING ALL MATERIAL

WOODEN CEILING-Providing and fixing of wooden ceiling

using 12 mm ply of brand greenply ecotech mr,century

sainik mr,archiply etc, , aluminium channel & pipe(50 x

mm) for framing and suspension, screws etc. including all

vertical support and all vertical surfaces from

51 ceiling,necessary hardwares,75mm anchor fastners and SqM 81.79 2477.61

complete with all material, making of coves and cutouts for

and Paise Sixty

ac grills ,labour & scaffolding with all lead, lift and transport.

and finished and complete the work satisfactorily as per

instruction of architect or Engineer-in charge.

CEMENT SHEET CEILING-Providing and fixing of cement

ceiling using 10 mm cement sheet of brand T.P.I,SHERA

(single sides), etc. using aluminium framing of 25mm x

50mm x 1 mm in 600 x 600 mm grid,and same pipe for

vertical framing, including all hardware item, aluminium L

clits, 25 mm powder coated self drilling screws,groove (if

52 shown) with all material, 75 mm anchor fastners,making of SqM 42.58 2626.34

coves for indirect lighting, grooves,cutting

,labour,SCAFFOLDING, lead and wastage etc. complete. And

Finished with satin finish wall color and complete the work

satisfactorily as per instruction of architect or Engineer-in

G.I SOLID BAFFLE CEILING -Providing and fixing of SOLID Rupees Four

53 G.I metal baffles on ceiling or wall of Galvanized Iron Baffle SqM 143.67 4040.00 Thousand Forty

Panel OF 50 mm x 100 mm with center to center distance and Paise Zero

GLASS PARTITION WITH FILMWORK-Providing and fixing of

full height glass partitions (AS PER DRAWINGS) using patch

fitting / 25 or 50 mm U-channels with powder coating

12mm clear toughned glass,film work as per drawing

54 including all hardware items,silicon,etc with all material, SqM 114.00 4127.00

labour,cutouts,edge polish , lead and wastage etc. and

complete the work satisfactorily as per instruction of

architect or Engineer-in charge.

ABOVE CEILING PARTITION-Providing and fixing of above

ceiling partitions (AS PER DRAWINGS) using 75 mm x 50 mm

x 1 mm aluminium pipe for framing,with ghana wood infill

etc. including all hardware item, with all material, labour,

55 SqM 21.00 2457.37 Hundred Fifty

lead,scaffolding and wastage etc. and complete the work

Seven and Paise

satisfactorily as per instruction of architect or Engineer-in

Thirty Six Only

WOODEN PARTITION-Providing and fixing of full height

solid sandwitch partitions (AS PER DRAWINGS) using 50 x

mm aluminium pipe for framing (minimum grid size of

mmx 600mm ), 12mm ply (both sides)of brand greenply

ecotech mr,century sainik mr,archiply etc, teak wood

beading patti etc. making of rebates and including all

hardware items, groove (if shown)50 MM TK , 24 kg density

56 SqM 74.00 4707.16 Hundred Seven

insulation if required,with all materials,hardwares,ss or

powdercoated screws, labour, lead and wastage,scaffolding

etc. complete. And Finished with different materials,and

complete the work satisfactorily as per instruction of

architect or Engineer-in charge.

SINGLE GLASS DOOR SIZE(APRROX SIZE OF 0.90 X 2.45)-

Providing and fixing of 12 mm tk toughned GLASS DOORS

using Dorma Xl-C 4001 Glass Door PKG EN 3 (Top Patch-1,

Bottom patch-1, Floor Spring-1, Corner Lock-1); Dorma Xl-C

4003 A Patch fitting for overpanel and sidelight; Dorma Xl-C

4004 A Connector for overpanel and Sidelight; Dorma Xl-C

57 4008 Side Connector; Dorma Xl-C 3000 H Type Handle NO 2.00 37584.66

Eighty Four and

400x22 CTC 300 AND AS PER DRAWING including all

Paise Sixty Six

acceessories,locks, material, silicone,labour,installation,

Hole & slote charges etc. and complete the work

satisfactorily as per instruction of architect or Engineer-in

SINGLE DOOR SIZE(APRROX SIZE OF 1.20X2.45) WITH

FIXED GLASS TOP (APRROX SIZE OF 1.20 X 0.75 to 1.05)-

Providing and fixing 12 mm tk of toughned GLASS DOORS

using Dorma Xl-C 4001 Glass Door PKG EN 3(Top Patch-1,

Bottom patch-1, Floor Spring-1, Corner Lock-1); Dorma Xl-C

4003 A Patch fitting for overpanel and sidelight; Dorma Xl-C

4004 A Connector for overpanel and Sidelight; Dorma Xl-C

4006 Central Connector; Dorma Xl-C 4008 Side Connector; NO 4.00 45668.64

Sixty Eight and

Dorma Xl-C 3000 H Type Handle 400x22 CTC 300 , AND AS

Paise Sixty Four

PER DRAWING including all acceessories, locks,material,

silicone,labour,installation, Hole & slote charges etc. and

complete the work satisfactorily as per instruction of

architect or Engineer-in charge.

REFURBISHING THE EXISTING DOOR-Providing and fitting of

6mm ply & 1mm laminate on both the side (as per drawing

& selection) brand greenply ecotech mr,century sainik

mr,archiply etc on existing flush door and 25 mm to 50 mm

tk teakwood beading patti for liping,framing and

ACOUSTICAL PANNEL as per selection, and finishing it with

laminate with 3mm x 3mm grooves if shown ,including all

material, labour and hardware,125 mm s.s 304 grade

hinges,fissure screws with plugs , heavy duty conceal door

58 SqM 8.82 5800.72 Hundred and

closer AND FLOOR SPRING , mortise door lock with entire

set including cylinder as selected,tower bolt,stopper,colour

REMOVING OF OLD LAMINATE IF APPLIED and polish work

as per instructions etc waste of materials, and complete the

work satisfactorily as per instruction of architect or Engineer-

in charge.[Basic Rate of Laminate : 2400rs./sheet (8' x 4')]

TRAP DOOR FOR SERVICES-Providing and fixing of

TRAPDOOR for ac using TWO SHUTTERS OF 25mm flush

door( Made from pine framing AND AS PER DETAIL) for

shutter & 18 mm ply for framing and vertical support (AS

PER DRAWINGS)of brand door house or equivalent Rupees Four

etc,ghana wood beading patti etc. including all hardware Thousand Nine

59 items like 4 nos alllenkey lock ,stopper, hinges, groove (if SqM 4.50 4981.68 Hundred Eighty

shown) with all materials, labour, lead and wastage etc. One and Paise

complete. And Finished with different materials,and Sixty Seven Only

complete the work satisfactorily as per instruction of

architect or Engineer-in charge.(BASIC AREA OF TRAP DOOR

IS 2.40X 2.00 MT (As per Dwg.) = 4.80 sq.m.

ACOUSTIC DOOR FOR AUDITORIUM-Providing & fixing of

teakwood door frame of section 150x65mm along with fire

and smoke in tumescent seal strip of size 12mmx4mm for

120 minutes fire rated and rw 35db acoustic door with

minimum thickness of 93mm having infill of 50mm thick

Knauf make glass wool of 48kg/m3 density sandwiched by

two 12mm thick magnesium board (edge to edge on

internal hardwood frame) and cladded with 6mm thick

commercial ply facing and 3mm sheet rubber interlayer And

finished with 1mm thick laminate as per designer and 25mm

thick teakwood frame around the door panel as shown in Rupees Ten

the drawing. The board shall be resistant to vermin, mold Thousand One

growth, minor impact, abrasion and short term water attack Hundred and

shall have acoustic seal in door rebates and drop dead seal

at the bottom of the door, the sound reducing doors also

include door closer, door coordinator, panic bar with

outside key and handle etcwith all materials, labour, lead

and wastage etc. complete. And Finished with different

materials,and complete the work satisfactorily as per

instruction of architect or Engineer-in charge.

WOODEN PANELLING-Providing and making of ply panelling

on Wall & columns using 12mm ply brand greenply ecotech

mr,century sainik mr,archiply etc , aluminium pipe for (2" x

1") framing(minimum grid size of 600 mmx 600mm ), Ghana

bidding patti (11/2" x 3/4") with depth upto 450 to 500 mm

if required including all material, labour and hardware

61 complete,including scaffolding with 50 mm thick glass SqM 655.67 3013.11

wool with 6 to 8 mm perforation in equal distance as per

instruction of architect. And Finished with different

materials,polish work as per instructions,and complete the

work satisfactorily as per instruction of architect or Engineer-

MDF FINISH WITH LAMINATE FINISH-Providing and fitting

MM MDF of 1 mm laminate (as per drawing & selection) of

brand greenlam,merinolam,century etc on ply partition

with 25 mm x 20 mm teakwood beading patti design on top

as per drawing,and 3mm x 3mm bar code pattern grooves if

shown, all material, adhesives,polish work in groove ,labour

62 SqM 409.35 2153.60 Hundred Fifty

and hardware, waste of materials,polish work as per

Three and Paise

instructions, complete as per instruction of architect.[Basic

Fifty Nine Only

Rate of Laminate : 2400rs./sheet (8' x 4')] and complete the

work satisfactorily as per instruction of architect or Engineer-

ACOUSTICAL PANEL FINISH-Providing and fitting of acoustic

panels with Standard size & thickness of

1220*2420*9mm.of brand Artois,KANUF

ARMSTRONG,ecotone,trnaquil ,only.IN GRADIENT

PATTERN,including synth pf of 24kg density,Panels should

have Sound Absorption coefficient (NRC) 0.84.

Formaldehyde emission standards of GB18580-2001 class

E1, it should be a green material with asbestos-free, non-

toxic and tasteless gas under extreme temperature,

protecting the ozone layer, non-irritant and recyclable. Rupees Three

acoustic panels have to be Fire-resistant as per China Thousand Sixty

63 standard class B1. Good insulation properties, to prevent SqM 387.30 3061.95 One and Paise

transmitting the heat from outdoor to indoor directly as Ninety Four

partition or and ceiling, saving 35% of energy, extending the Only

life of air conditioning.including all acceessories,synth pf,

material,cutting work of approved finishing,adhesives,

behind pannel black out paint work on ply , labour etc. and

complete the work satisfactorily as per instruction of

architect or Engineer-in charge.(Basic rate of PANNEL-135

CARPET FLOORING(CUT PILE)-Providing and fixing of

approved quality Carpet tile of brand Toli Yutaka,including

all acceessories, material, labour etc. complete. (Basic rate

of Carpet- 150 rs/sq.ft.)Surface should be BCF Nylon

with Stain Release. Base fabric should be nonwoven

polyester with glass fibre and pvc backing. Size of tile should

be 500mm x 500 mm x 6mm with a pile height of 3 mm.

Area of use shall be heavy commercial. CRI Green Label Plus

Certification is GLP9978. Performance specifications include

smoke density of less than 450 (ASTM E662), Electrostatic

64 SqM 4.65 2099.62 Ninety Nine and

Propensity of 1.1kv (AATCC 134), Surface Flammability

Paise Sixty Two

passes CPSC FF 1-70 (ASTM D2859), Dimensional Stability as

per ASTM D 7570 and delamination strength exceeds

backing strength.(Basic rate of CARPET-160

rs/sq.ft.)installation , adhesives,primer work,etc, as per

instruction of Architect or Engineer-in charge.

BRAND ( TOLI,VITOFLOOR,UNITEX,MILLIKEN)

LAMINATED WOODEN FLOORING INC. ALL-Providing and

fixing of approved ac4 - ac5 quality 12 mm laminated

wooden floor(WITH V-GROOVE) including all accessories,

skirting profiles , reducer profiles, corner profiles ,vapour

barrier/ hitlon ,material, labour,installation etc. guranteed

for 20 years and class 23 heavy usage oin domestic area.and

65 SqM 1.68 2155.86 Hundred Fifty

complete the work satisfactorily as per instruction of

architect or Engineer-in charge.(Basic rate of wooden floor-

Eighty Six Only

150 rs/sq.ft.)BRANDS: PARADOR , QUICK STEP , KRONO

ORIGNAL GERMANY.

BEADING PATTI PANNELING-Providing and fixing of 38 MM

X 38 MM VALSADI TEAKWOOD , as per drawing at VARIOUS

distance as per design including pu and 3 SIDE polish work

on all sides of patti as per selection including all material,

66 RMT 108.00 1396.61 Hundred Ninety

labour,and hardwares, waste of materials,etc and complete

the work satisfactorily as per instruction of architect or

Engineer-in charge.

WALL COLOR - SATIN-Providing and applying satin paint of

approved quality, company and shade upto finishing (min

coats) including lappi and primer work and all material,

67 labour including scaffolding etc. and complete the work SqM 1.00 343.40

Three and Paise

satisfactorily as per instruction of architect or Engineer-in

charge. (Basic rate of SATIN paint- 28 rs/sq.ft.)

PLASTIC PAINT-Providing and applying plastic paint of

approved quality, company and shade upto finishing (min

coats) including all material, labour including scaffolding etc.

68 and complete the work satisfactorily as per instruction of SqM 996.64 224.22

architect or Engineer-in charge. (Basic rate of plastic paint-

POP PUNNING-Providing and fixing of POP Punning and

finished by company approved gypsum, taping, lapi,

including scaffolding etc. and including grooves as shown in

drawing And including satin paint complete with all

69 material, labour with all lead, lift and transport.and SqM 150.00 275.73

complete the work satisfactorily as per instruction of

architect or Engineer-in charge.(Basic rate of POP PUNNING

WITH TACHA WORK - 22 rs/sq.ft.)

PODIUM TABLE-Providing and fixing of MAIN TABLE FOR

AUDITORIUM including AND SPEAKER DICE,AND REQUIRED

LOGO WORKS ON IT as per drawings and instructions

provided, using ply of brand greenply ecotech mr, century

sainik mr, srg etc., aluminium pipe for framing and finishing

it with 6 MM CORIAN of brand granium,Tranquil,dupont

,and 1mm unicore laminate and 1mm laminate of brand Rupees Twenty

greenlam or selected by the architect (basic rate of unicore Eight Thousand

70 laminate is 3000 per sheet and other 1mm laminate is 2000 No. 1.00 28280.00 Two Hundred

per sheet, of size 8'0 x 4'0) including all material,m.s Eighty and

nylon leveler foot rubber, waste of materials ,polish work as

per instructions etc. and complete the work satisfactorily as

per instruction of Architect or Engineer-in charge. (APPROX

RUNNING LENGTH OF TABLE IS 1.20 MT.)

FLODING TABLE (1.20 X 0.75)-Providing and fixing FLODING

TABLE ON STAGE of brand as per architects selection,and

71 complete the work satisfactorily as per instruction of No. 0.00 7070.00

architect or Engineer-in charge.(basic rate per piece is 5000/-

STORAGE UNIT WITH LAMINATE FINISH-Providing and

Making of Storages (AS PER DRAWINGS) using ply of brand

of brand greenply ecotech mr,century sainik mr,srg

etc,(thickness as specified)/ sag wood and finished by 1 mm

Laminate outside as per selection of brand

greenlam,merinolam,formica or 6mm HDF as per drawing,

1mm tk laminate (inside),water pu polish (as shown), Rupees Twelve

drawers, shelves,with profile shutter with glass etc. with all Thousand Four

72 hardware, nylon leveler foot rubber, handles,hinges, locks , SqM 33.00 12410.43 Hundred Ten

magnet and other acessories with all material, and Paise Forty

installation,labour, lead and wastage,polish work as per Two Only

instructions etc. and complete the work satisfactorily as per

instruction of architect or Engineer-in charge.(Basic rate of

Inside Laminate : 18 rs./sq.ft. & Outside Laminate :

SOFA - 3-SEATER(AUDI)-Providing and fixing 3-seater

sofa,as per drawings or selection using base WHITE ASH

WOOD for framing with molded foam,and high density fom

warwick brand rexine(as per architects selection) in sofa

upholstery and ss204 grade corner legs with 5 years

73 No. 4.00 25755.00 Seven Hundred

warranty and instructions provided, and ,and complete the

work satisfactorily as per instruction of architect or Engineer-

in charge..(appox lenght of sofa is 7'6'') BASIC RATE

3400/RN FT.BRANDS : COHUMAN,DVARK,STEARLING

CORNER TABLE & CENTER TABLE (approx 0.60 X 0.60)-

Providing and fixing center or corner table of brand as per

architects selection,with ms base with powder coating and

top will be glass or stone as per selection and complete the

74 No. 8.00 6565.00 Hundred Sixty

work satisfactorily as per instruction of architect or Engineer-

in charge.(basic rate per piece is 6000/-

)COHUMAN,DVARK,STEARLING

PLASTIC CHAIR WITH CUSIONING FOR ALL VISITOR -

Providing and sulppying plastic chair with cusining of High-

grade 100 percent virgin polymers which ensure its

longevity,Ergonomically designed plastic chair for home Rupees Two

with a lacquered finish, heavy-duty armrest, back and seat Thousand Five

75 cushion made up of velvet upholstery and PU material for No. 0.00 2525.00 Hundred

maximum comfort as per selection and complete the work Twenty Five and

charge.Basic rate of chair is 2200/- per chair BRANDS

:Supreme Ornate

DINING TABLE WITH 6 CHAIR-Providing and fixing of

DINING TABLE with 6 chair of size 1.80 MT DIA using

mm nano white stone (basic rate 650 sqft) at top with dhar Rupees Thirty

polish and fabricated base of ms frame with powder Eight Thousand

76 coating AS PER SELECTION WITH 6 plastic CHAIRS with No. 0.00 38380.00 Three Hundred

cushioning (BASIC RATE 1500) as per drawing or selection Eighty and

architect or Engineer-in charge

ROLLER CURTAIN-Providing and fixing of approved quality

roller blinds using MARVEL ,phifer fabric of premium grade,

with roller tube, bottom bar leveller made of extruded

aluminium alloy an Idler, Insert Type- Brackets, PVC chain

etc. all complete at all floor and heights as per approved

specification. Roller Tube Control, Clutch, Idler Side by side

or single Roller Tube of extruded Aluminium 38mm inner

dia - 41mm outer dia minimum wall thickness of 1.6mm.

Roller blind - roller blind fabric should be made up of 35%

FibreGlass, 65% PVC, it should have specific low emissivity

treatment and lead free with Greenguard gold certification. Rupees One

It should have 3% to 5% openness, fabric thickness should Thousand Four

77 be 0.43 mm, mesh weight approx 400 gms/ sqmtr. It should SqM 15.50 1483.43 Hundred Eighty

cut UV rays, with antimicrobial properties preferably with Three and Paise

Microban. The fabirc should be Flame retardant and Lead Forty Two Only

Free. It should be GreenGuard certified with Gold Standard

for low chemical emissions for indoor use. (Basic rate of

Roller blinds- 110rs/sq.ft.)including all accessories, material,

labour,installation etc..and complete the work satisfactorily

as per instruction of architect or Engineer-in charge..

BACKLIT LOGO-(GMC LOGO) : Providing and fixing of

BACKLIT LOGO& FULL Name Text (GMC) in LETTERS size of

300 to 450 mm as per design using 10 mm clear Acrylic cut

work and fixing 3mm acrylic on top of brand Ptglass,astari

etc, 4mm Acp of 0.5 mm tk for profiling,as per detail,3M

vinyl with 5 years warranty on fading with all laser and cnc

work,including all material,osral led modules including

78 SqM 4.25 15150.00 Hundred Fifty

drivers as required with 5 years warranty , labour,all

required m.s fabrication,100 mm ss studs for mounting and

other hardwares, waste of materials,scaffolding,

labour,lead, transport, and installation, etc and complete

the work satisfactorily as per instruction of architect or

Engineer-in charge.

S.S NAME PLATE SMALL-Providing and fixing of 2MM TK S.S

316 GRADE matt finish NAME PLATE with cut work and

fixing 3mm acrylic on top or behind of brand Ptglass,astari

etc,with all laser and cnc work,and wooden finish back

board ,including all material,SCAFFOLDING labour,15 mm ss

79 No. 20.00 1515.00 Hundred Fifteen

studs for mounting and other hardwares, waste of materials

etc and complete the work satisfactorily as per instruction

of architect or Engineer-in charge.( BASIC SIZE OF NAME

PLATE 150 MM X 900 MM)

HANGING LIGHT DECORATIVE-Providing & fixing of

DECORATIVE HANGING LIGHT with box type aluminium

housing ,frosted acrylic at bottom OR CHROME AND METAL

WITH BULBS , end caps,hanging strings etc as per selection Rupees Fifty

with 48 watt Tranquil led strips & driver suggested & as Thousand Five

directed by EIC/Consultant.and complete the work Hundred and

charge.( BRAND wipro,philipes,jaguar OR EQUIVALENT)

BASIC RATE 42500 PER NO

LED COB LIGHT 16-20W (LED Spotlight, 30 Degree Spread)-

Supplying and erecting LED indoor fittings with LEDs of

wattage of 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of

thick sheet Steel conforming to IS : 513 / CRCA polyester

powder coated and high U.V & corrosion resistance with

diffuser and/ or Polycarbonate optics with company mark /

name engraved or embossed. 120 to 300V, Power Factor Rupees Two

more than 0.9, THD < 10%, CCT 3000K to 6500K, Uniformity Thousand Seven

ratio > 0.7, Luminaire efficacy > 85 lumens/watt. LED driver Hundred

efficiency > 85%. CREE / OSRAM / PHILIPS LUMILEDS / Seventy Seven

NICHIA / SEOUL / BRIDGELUX (U.S.A) make LED used for and Paise Fifty

luminaire with Lumen output of 600 to 1200 lm. (Each Only

fitting required LM-79 & LM-80 certificates) (C) Square

/Circular, Surface / Recessed Mounted Downlight with High

Power COB LED as light source provision for spring loaded

mounting clips complete. Final Decison is Taken By

EIC/Consultant.

PAINTING - 24"X24"-Providing and fixing of 24" x 24"

painting with fibre frame with good quality digital laser Rupees Four

printing paper should be 200 gsm and pasting on hard board Thousand Sixty

82 backing hand painting on canvas as per selection and No. 10.00 4065.25 Five and Paise

complete the work satisfactorily as per instruction of Twenty Five

architect or Engineer-in charge.Basic rate of painting is Only

3500/- per painting

PAINTING - 36"X36"-Providing and fixing of 36" x 36"

painting with fibre frame with good quality digital laser Rupees Seven

printing paper should be 200 gsm and pasting on hard board Thousand Five

backing or hand painting on canvas as per selection and Hundred Forty

complete the work satisfactorily as per instruction of Nine and Paise

architect or Engineer-in charge.Basic rate of painting is Seventy Five

6500/- per painting Only

PLANTER WITH REAL PLANTS-Providing and fixing 13 inch

dia planter/pots of frp or plastic including drain tray with

real indoor plants as per selection,including 3 feet ht plants Rupees Three

of brand seasonal dekor or as per selection and complete Thousand Thirty

the work satisfactorily as per instruction of architect or and Paise Zero

Engineer-in charge.(BASIC RATE OF POT IS RS 1880/-) Only

PLANTER WITH ARTIFICIAL PLANTS-Providing and fixing of

22 inch dia planter/pots of roto moulded plastic with

artificial indoor plants as per selection and including

artificial plants of 4 feet ht of brand seasonal dekor or as per

85 No. 1.00 6211.50 Hundred Eleven

selection,complete the work satisfactorily as per instruction

and Paise Fifty

of architect or Engineer-in charge.(BASIC RATE OF

ARTIFICIAL PLANTER IS RS 2900/- AND POT IS RS 1980/-)

WALL CLOCK-Providing and fixing of 12 to 16 inch dia

wallclocks of brand quartz or as per selection and complete

the work satisfactorily as per instruction of architect or

86 No. 3.00 1212.00 Hundred Twelve

Engineer-in charge.(basic rate of wall clock is rs 1020/-per

INDOOR FLOOR MAT-Providing and fixing indoor floor matt

of brand my floor or as per selection and complete the

work satisfactorily as per instruction of architect or Engineer-

87 No. 3.00 1111.00 Hundred Eleven

in charge.(basic size of matt is 1.20 x 0.60 mt)

PVC DUSTBIN-Providing & Supplying of 8 to 10 in dia and

to 15 inc ht P.V.C. Dustbin of brand cello,pigeon etc. Rupees Eight

complete as per selection & directed by the Architect and Hundred Fifty

approved by the Engineer in Charge.(BASIC RATE OF Eight and Paise

DUSTBIN IS RS 722/- ) Fifty Only

MIRROR FINISH(5mm thick Looking Mirror)-Providing and

fitting of mirror/glass (as per drawing & approved shade)of Rupees One

brand ais,modiguard,etc on ply panelling / on tile cladding Thousand Nine

89 including all material, labour and hardware, cutouts, edge SqM 22.75 1937.15 Hundred Thirty

polishes,waste of materials and complete the work Seven and Paise

satisfactorily as per instruction of architect or Engineer-in Fourteen Only

FLOOR PROTECTOR-Providing and fixing of 5 MM FLOOR

PROTECTOR as per selection ,taping,removing and cleaning Rupees Sixty

90 the surface,and complete the work satisfactorily as per SqM 750.00 65.65 Five and Paise

instruction of architect or Engineer-in charge. Sixty Five Only

SCAFFOLDING -Providing and fixing of bamboo scaffolding,

for entire project as per requiremnt of the agency with Rupees Ten

fixing and removing the entire scaffolding after the work Thousand One

completion and complete the work satisfactorily as per Hundred and

DEEP CLEANNING WORK-Providing and cleanning for the

enitre AUDITORIUM HALL and other area as well from Rupees Forty

starting to the end of the project with deep cleaning Five Thousand

92 satisfactorily as per instruction of architect or Engineer-in Job 2.00 45450.00 Four Hundred

charge. Fifty and Paise

TERMITE TREATMENT IN FLOORING AND WALL-Providing

and Spraying imidaclopid30.5%sc(primise from bayer)on all

conference walls and slab surface before tiling, after that

Making 10 mm Holes at the interval of 1’-0’’ft at the

Junction of floor & Wall & Sides of all wooden frames,

pressurizing imidaclopid30%sc(primise from bayer) ( Rupees Eighty

93 approved Chemical for Termite Control by central SqM 1500.00 80.80 and Paise Eighty

Insecticide Board, Gov. Of India and recommended by Only

bureau of Indian Standards ) [ IS 6313 : 1981 Part II – III ] in

to it & fill it with cement. and complete the work

satisfactorily as per instruction of architect or Engineer-in

Automatic Air Freshener Dispenser With Refill-Providing & Rupees Two

Supplying of automatic air freshener dispenser with bottle Thousand Nine

of aroma with batteries . complete as per selection & Hundred Three

directed by the Architect and approved by the Engineer in and Paise

Charge.(BASIC RATE OF AIR FRESHENER IS RS 2500/- ) Seventy Five

EPOXY-Providing & applying Roff Rainbow Tile Mate Epoxy

Grout is a three-component epoxy-based tile joint filler.It

consists of a resin, a hardener, and a filler.Water-Resistant:

This epoxy grout is waterproof, Stain-Free: It resists stains

and won’t absorb liquids.Crack-Free: The grout ensures

minimal water seepage due to its crack-free Rupees One

properties.Chemical-Resistant: It withstands exposure to Hundred One

various chemicals.Hard-Wearing: Designed for durability and Paise Zero

and longevity.Impervious: Provides a high degree of Only

resistance to abrasion, impact, and shocks. color as per

selection & directed by the Architect and approved by the

Engineer in Charge.

Providing and erecting approved make split air-conditioning

unit consisting of copper condensing unit with fan motor,

hermetically sealed rotary compressor with accessories etc.

duly connected separately erected evaporating unit and

blower motor with its accessories by means of extra

96 supplied proper insulated copper tubing,drain PVC pipes Ea. 4.00 38820.36

suitable for ( cost includes powder coated Stand, Eco

Paise Thirty Six

Friendly green gas charging, 15A plug top & Remote

Control) with necessary core cutting. (c) for 2 ton capacity

Supplying & installing MS standard type stand mounting for

outdoor unit of Split A.C. upto 4 TR capacity erected with

necessary hardware materials as directed.

97 Ea. 4.00 643.37 Three and Paise

Supplying and erecting insulated pair of soft copper tubing

open or concealed including power and control

cable,necessary PVC drain pipes for Split AC machine up to

98 Rmt. 80.00 822.14 Twenty Two

Supply, Installation, testing and commissioning including

vaccumiazation and Nitrogen testing of following nominal

sizes of soft/hard drawn copper refrigerant piping for VRV

system, complete with fittings, with suitable adjustable ring

type hanger supports, jointing/brazing including accessories,

insulated with XPLE Class-0 tubular insulation/with Class-0 Rupees Five

closed cell elastometric nitrile rubber tubular sleeves Hundred Sixty

sections of specified thickness as given below for Suction Six and Paise

and Liquid lines, all accessories as per specifications etc with Sixty One Only

necessary refrigerant joint as required :(D) 15.86 mm dia

(OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm

thick insulation

(E) 19 mm dia (OD) (Hard drawn) with tube thickness

mm with 19 mm thick insulation

Eight and Paise

(F) 22.2 mm dia (OD) (Hard drawn) with tube thickness

mm with 19 mm thick insulation

101 Mtr. 100.00 822.14 Twenty Two

(G) 25.4 mm dia (OD) (Hard drawn) with tube thickness

mm with 19 mm thick insulation

Eight and Paise

Fifty Nine Only

(H) 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 Rupees One

mm with 19 mm thick insulation Thousand

103 Mtr. 120.00 1028.18 Twenty Eight

(I) 31.8 mm dia (OD) (Hard drawn) with tube thickness

mm with 19 mm thick insulation

104 Mtr. 80.00 1079.69 Seventy Nine

and Paise Sixty

(J) 34.9 mm dia (OD) (Hard drawn) with tube thickness

mm with 19 mm thick insulation

(A) Cord type remote control with thermostat, LED Display Rupees One

and internal wiring for Cassette, FCU & CSU Thousand Five

and Paise Sixty

Providing installing, commissioning, testing approved

make air cooled package units of following capacity

complete with hermetically sealed scroll compressor Of

following TR @ 400 CFM(minimum) per TR capacity with

maximum noise level 60 dB from 1 mtr from indoor unit and

remote located condensing unit and evaporating unit with

inter connecting copper refrigerant piping up to 10 RMT.

comprising of following

(A) The condensing unit complete with condenser fan

motor, & the condenser which effectively achieves heat

107 rejection by utilizing cooling medium as air, in fan and Ea 4.00 229103.35

cooling type condenser

Three and Paise

(B) The evaporating unit complete with Scroll compressor

Thirty Five Only

DX coil evaporator, centrifugal blower, blower motor,

starter, complete with first charge of Eco Friendly Green

gas and oil with refrigerant piping, inter connecting indoor

and outdoor unit and drain canvass connection & condenser

M.S. structure with red oxide and/or RCC Pedestal and

approved paints [D] For 11 TR

Supply Installation Testing Commissioning of 18000 CFM

AHU with static pressure with Supply, Return, Exhaust &

108 Fresh Air , Coil 4 Row 40 TR & Air Filters (02 Nos Blower) No 1.00 606000.00

Nitrogen Testing & vacuuming for All Circuit

Supplying colourless non inflammable refrigerant Gas R-410 Rupees Seven

110 KG 60.00 770.63 Seventy and

MS Fabrication for condensing unit

Thirty Five Only

Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm

thick.nitrile rubber insulation.(B) 40 mm dia.

Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm

thick.nitrile rubber insulation.(C.) 32mm dia.

Seven and Paise

Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm

thick.nitrile rubber insulation.(D) 25 mm dia.

Seven and Paise

Supply, installation, balancing and commissioning of

factory fabricated GSS sheet metal rectangular/round

ducting complete with neoprene rubber gaskets, elbows,

115 splitter dampers, vanes, hangers, supports etc. as per Sq.Mtr. 550.00 1122.11

approved drawings and specifications of following sheet

thickness complete as required.A) Thickness 0.63 mm sheet

Supply, installation, balancing and commissioning of

factory fabricated GSS sheet metal rectangular/round Rupees One

ducting complete with neoprene rubber gaskets, elbows, Thousand Three

116 splitter dampers, vanes, hangers, supports etc. as per Sq.Mtr. 50.00 1301.89 Hundred One

approved drawings and specifications of following sheet and Paise Eighty

thickness complete as required(B) Thickness 0.80 mm sheet Nine Only

Supply, installation, balancing and commissioning of

factory fabricated GSS sheet metal rectangular/round

ducting complete with neoprene rubber gaskets, elbows,

117 splitter dampers, vanes, hangers, supports etc. as per Sq.Mtr. 20.00 1438.24

Eight and Paise

approved drawings and specifications of following sheet

thickness complete as required (C.) Thickness 1.00 mm

sheet (20Gauge)

Supply, installation, testing and commissioning of GI

volume control duct damper complete with neoprene

rubber gaskets, nuts, bolts, screws linkages, flanges etc, as

118 Sq.Mtr. 30.00 7156.86 Hundred Fifty

per specifications.

Eighty Six Only

Supplying, fixing testing commissioning of supply air diffuser

of powder coated aluminium with aluminium volume

control dampers with anti smudge ring & removable core

and size & shape as per site requirement and approved

119 Sq.Mtr. 6.00 11548.34 Hundred Forty

Eight and Paise

Thirty Four Only

Supplying, fixing testing commissioning of Return air diffuser

of powder coated aluminium without volume control

dampers with anti smudge ring & removable core and size &

120 shape as per site requirement and approved design.. Sq.Mtr. 9.00 7969.91

Supply and fixing of acoustic lining of supply air duct and

plenum with 25 mm thick resin bonded glass wool having

density of 32 kg/m³, with 25 mm X 25 mm GI section of

mm thick, at 600 mm centre to centre covered with

121 Reinforced Plastic tissue paper and 0.5 mm thick Sq.Mtr. 3.00 702.96

perforated aluminum sheet fixed to inside surface of ducts

Ninety Six Only

with cadmium plated nuts, bolts, stick pins, CPRX compound

etc. complete as required and as per specifications.

Supplying and fixing of following thickness duly

laminated aluminum foil of mat finish closed cell Nitrile

rubber (Class "O") insulation on existing duct after Rupees Seven

applying suitable adhesive for Nitrile rubber. The joints Hundred Forty

122 shall be sealed with 50 mm wide and 3 mm thick self Sq.Mtr. 550.00 745.38 Five and Paise

adhesive nitrile rubber tape insulation complete as per Thirty Eight

specifications and as required.(A) 19mm Only

Supplying and fixing of following thickness duly

laminated aluminum foil of mat finish closed cell Nitrile

rubber (Class "O") insulation on existing duct after

applying suitable adhesive for Nitrile rubber. The joints

123 Sq.Mtr. 200.00 933.24 Three and Paise

shall be sealed with 50 mm wide and 3 mm thick self

adhesive nitrile rubber tape insulation complete as per

specifications and as required (B) 25mm

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire

of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multi strand copper wires up to 10 mtr

length , in below type of pipe erected with 6A Modular type

switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden box, Rupees Four

single mounting base frame covered with Hundred Forty

textured/metallic/white front plate modules erected on / in Nine and Paise

wall / ceiling as per pipe erected, with necessary Lamp Forty Five Only

holder/ceiling rose / H.D.Connector as directed.(f) with

medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete Cat. III

Point wiring for secondary light point with 2-1.5 sq.mm &

earth wire of 1.5 sq.mm (green) both are of ISI marked

KV grade FRLS PVC insulated multi strand copper wires, in

below type of pipe to be erected complete with earth

continuity and necessary connection with primary light with

accessories erected on Metal / PVC / wooden box covered

with 3 mm thick PC(Polycarbonate) / Acrylic sheet for open

125 / concealed wiring. with necessary Lamp holder / ceiling Point 339.00 135.82

rose / H.D.Connector as directed.Note:- Maximum up to

Eighty Two Only

mtrs length, excess will be considered as Mains for

Secondary Point. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete

Point wiring for Two Way Controlled Light Point with 2-1.5

sq.mm & earth wire of 1.5 sq.mm (green) both are of .ISI

marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires erected in below type of pipe with 6A Modular

type switches and following type of accessories erected on Rupees Five

PVC / Metallic/Wooden box, single mounting base frame Hundred Thirty

126 covered with textured / metallic/white front plate modules Pt 6.00 530.25 and Paise

erected on / in wall / ceiling as per pipe erected. with Twenty Five

necessary batten/angle holder or ceiling rose or Only

H.D.Connector as directed. (a) with medium class Rigid PVC

pipe and accessories erected flushed on wall/ceiling

complete Cat. III

Point wiring for FAN with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS

PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected with 6A Modular type

switch and hum free EME four or more step type electronic

fan regulator with separately mounted and accessories with

earth continuity of following type erected on PVC /

127 Metallic/Wooden box, single mounting base frame covered Point 8.00 629.23

with textured/metallic/white front plate modules erected

on / in wall / ceiling as per pipe erected. with necessary

ceiling rose / H.D.Connector as directed. (f) with medium

class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete

Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front

plate , modules erected with necessary connections as per

128 site situation directed by Engineer In charge.(23) USB Ea 30.00 650.44

and Paise Forty

Charger with output of 5 V DC,2.1 A with inbuilt surge

Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC / Rupees Four

Metallic/Wooden box covered with appropriate front plate Hundred

129 modules erected on / in wall / ceiling as per pipe erected Point 37.00 473.69 Seventy Three

with following type of accessories.[I] For 6A Plug and 6 a and Paise Sixty

switch with 2-1.5 sq.mm Cu. Wire from nearby Nine Only

switchboard/mcb db board (f) with medium class Rigid PVC

pipe and accessories erected concealed in wall/ceiling

complete CAT III

Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate

130 modules erected on / in wall / ceiling as per pipe erected Point 45.00 669.63

with following type of accessories.(III) [II] For 16A Plug and

Sixty Three Only

16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db

board.(a) with medium class Rigid PVC pipe and accessories

erected flushed on wall/ceiling complete CAT III

Point wiring for on board Looped Plug with 6A Modular type

switch & 5 pin socket erected on PVC / Metallic/Wooden Rupees Two

box, single mounting base frame covered with textured / Hundred Forty

metallic/white front plate modules erected on / in wall / One and Paise

ceiling with following type accessories Cat. III Thirty Nine Only

Providing & erecting Switch board for Computer or electric

apparatus consisting of following modular type accessories

mounted with PVC / Metallic concealed/open box with

single mounting base frame covered with textured/metallic Rupees One

/white front plate,modules erected with necessary Thousand

132 connections as directed Each 10.00 1081.71 Eighty One and

1 no. 6A/16A universal plug-switch combined. Paise Seventy

3 nos. 6A Switch One Only

3 nos. 6A 5 pin Plug For Modular Type Accessories Cat. III

Providing following type of Modular Type Accessories

mounted with pvc / metallic box, single mounting base Rupees One

frame covered with textured / metallic front plate , modules Hundred Fifty

erected with necessary connection. As desired by Engineer Three and Paise

In charge (8) Computer RJ-45 socket Cat III Fifty Two Only

(7) Blank Plate Single Cat.III

(19) Modular Indicating Call Bell Cat.III Rupees Three

135 Each 3.00 314.11 Fourteen and

Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected concealed in /flushed

on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC

136 Mtr. 1250.00 59.59 Nine and Paise

insulated stranded wire of green colour for earth continuity

Fifty Nine Only

of following size (A) with medium class Rigid PVC pipe and

accessories (a) 2 wire 1.5 sq. mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected concealed in /flushed Rupees Seventy

on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC Eight and Paise

insulated stranded wire of green colour for earth continuity Seventy Eight

of following size (A) with medium class Rigid PVC pipe and Only

accessories (b) 2 wire 2.5 sq. mm

providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected in / on wall / ceiling Rupees One

with 2.5 sq. mm copper conductor FRLS PVC insulated Hundred Seven

stranded wire of green colour for earth continuity of and Paise Six

following size (A) with medium class Rigid PVC pipe and Only

accessories (a) 2 wire 4 sq. mm (POWER PLUG AC)

providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected in / on wall / ceiling

139 with 2.5 sq. mm copper conductor FRLS PVC insulated Mtr 100.00 140.39

and Paise Thirty

stranded wire of green colour for earth continuity of

following size A (b) 2 wire 6 sq. mm

Providing and erecting Annealed bare Copper wire 8 to

140 Kg 15.00 794.87 Four and Paise

Supply, Installation, Testing and Commissioning of suitable

sweep, BEE 5 Star rated, Ceiling fan with Brush Less Direct

Current (BLDC) permanent ferrite magnet Motor, class of

insulation: B, Rust free 3 nos.Aluminium blades, 2 nos.

canopies, shackle kit with earthing provision, copper

winding, Power factor not < 0.9, Service Value (CMM/W)

minimum 6.85, Air delivery minimum 215 CMM, 350 Rupees Two

RPM,230v (tolerance as per IS : 374-2019), THD < 10%, with Thousand Eight

141 remote unit for Speed Control and all remaining accessories Ea 8.00 2885.57 Hundred Eighty

including safety pin, nut bolts, washers, temperature rise = Five and Paise

75 degree C (Max.), suitable for 140 to 285 Voltage and Fifty Seven Only

rectifier circuit with surge, over current and overload

protection , 50 Hz, Single phase AC Supply, earthing etc.

Complete as required.[ Make shall be approved by Engineer

in Charge] (B) 1200 mm Sweep (48")

Supplying and erecting 19 / 20 mm. nominal bore Medium Rupees One

Class M.S. Pipe down rod erected duly painted for fan Hundred Eight

complete with proper insulation without leakage and and Paise Seven

Supplying & erecting fan hook box of 10 mm M.S. round

bar bounded to the RCC bars up to 50mm length each side

143 and pierced through a 16 Gauge M.S. box / Heavy Duty PVC Ea 8.00 108.07

and Paise Seven

box complete erected concealed in Ceiling with necessary

Supplying & erecting approved make low noise decorative

exhaust fan having square frame ABS body with inbuilt Rupees One

lowers & square frame. 200mm with 1350RPM Cat.II Thousand Seven

144 Ea 5.00 1703.87 Hundred Three

and Paise Eighty

Supplying & erecting single phase approved make industrial

exhaust fan suitable for medium duty ring mounted low Rupees Three

noise operation suitable for medium duty having following Thousand Three

145 dia size and maximum speed in RPM [D] 450 mm dia 900 Ea 5.00 3339.06 Hundred Thirty

RPM Cat.II Nine and Paise

Supplying & erecting Electronic Type Cordless Call Bell

erected on PVC/Metal board having portable bell push Rupees Two

working on D.C. & bell on 230V A.C. supply with cells / Hundred Thirty

battery Eight and Paise

Thirty Six Only

Supplying & erecting Approved make call bell indicator with

buzzing sound and Red light indicating lamp with Red light

147 button to attend the call suitable for 240 v 50 c/s supply to Ea 2.00 142.41

Providing and erecting ISI mark Medium class RIGID PVC

PIPES of following size complete to be erected on/in wall or

ceiling erected with necessary PVC fittings & Junction boxes

148 Mtr. 410.00 32.32 Two and Paise

fixed with adhesive solution & Clamps with following dia of

Thirty Two Only

pipes, in approved manner as directed (b) 25 mm

Providing & erecting PVC Corrugated Flexible Conduit with

required nos. of coupling, PVC bushes, Check-nuts etc.

149 Mtr 500.00 16.16 and Paise

complete of following sizes.(1) 20 mm

Providing & erecting PVC Corrugated Flexible Conduit with

required nos. of coupling, PVC bushes, Check-nuts etc. Rupees Twenty

150 complete of following sizes(3) 32 mm Mtr 50.00 26.26 Six and Paise

Twenty Six Only

Providing & erecting 16 gauge HGS conduit pipe (as per IS)

painted black surface/concealed of following size complete

to be erected on/in wall or ceiling with erected with

151 necessary saddles, screws, bends, junction boxes etc. with Mtr 250.00 104.03

and Paise Three

following (Nominal Bore) dia of pipes, in approved manner

as directed (2) 25 mm

Supplying and laying UPVC cable trunking system

comprising unplasticised polyvinyl, chloride rigid material

with ignition free and flame proof confirming BS with

152 necessary end caps Internal and external bend, flat bends, Mtr 100.00 409.05

coupler, tee etc..All necessary accessories and measuring of

following sizes (2) 100 mm x 50 mm trunking

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to house

153 appropriate nos. of MCBs.(The DBs should be used of same Ea 8.00 355.52

company of MCB to be used) suitable for (A) single phase

incoming and horizontal single phase outgoing (a) single

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS Rupees One

8623-1 & 3, IEC 61439-1 & 3 without MCB to house Thousand One

154 appropriate nos. of MCBs.(The DBs should be used of same Ea 4.00 1152.41 Hundred Fifty

company of MCB to be used) suitable for (A) single phase Two and Paise

incoming and horizontal single phase outgoing. (b) sheet Forty One Only

steel double door (IP-43). (iii)8 way

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to house

155 appropriate nos. of MCBs.(The DBs should be used of same Ea 4.00 1492.78

company of MCB to be used) suitable for (A) single phase

incoming and horizontal single phase outgoing. (b) sheet

steel double door (IP-43). (iv)12 way

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS Rupees Two

8623-1 & 3, IEC 61439-1 & 3 without MCB to house Thousand Nine

appropriate nos. of MCBs.(The DBs should be used of same Hundred

company of MCB to be used) suitable for (B) three phase Thirteen and

incoming and single phase horizontal type outgoing Per Paise Eighty

phase isolation type (PPI). (b) sheet steel double door. (ii)6 Five Only

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS Rupees Two

8623-1 & 3, IEC 61439-1 & 3 without MCB to house Thousand Nine

appropriate nos. of MCBs.(The DBs should be used of same Hundred

company of MCB to be used) suitable for (B) three phase Thirteen and

incoming and single phase horizontal type outgoing Per Paise Eighty

phase isolation type (PPI). (b) sheet steel double door. (iii)8 Five Only

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS Rupees Two

8623-1 & 3, IEC 61439-1 & 3 without MCB to house Thousand Nine

appropriate nos. of MCBs.(The DBs should be used of same Hundred

company of MCB to be used) suitable for (B) three phase Thirteen and

incoming and single phase horizontal type outgoing Per Paise Eighty

phase isolation type (PPI). (b) sheet steel double door. (iv)12 Five Only

providing and erecting Miniature circuit breaker single pole

6A to 25A suitable to operate on 240 V A.C. system and

159 having breaking capacity 10 KA to be erected in existing Ea 325.00 112.11

box. confirming to IS 8828/1996 with ISI Mark Cat.III

Providing & erecting 240 V MCB double pole switch for

lighting Load (B Curve) having 10 KA breaking capacity &

confirms to IS : 8828 in existing box having following

160 Ea 2.00 295.93 Five and Paise

capacity (B) 40 Amp. Cat.III

Providing & erecting 240 V MCB double pole switch for

motor & inductive load (C Curve) having 10 KA breaking

capacity & confirms to IS : 8828 in existing box having

161 Ea 2.00 299.97 Nine and Paise

following capacity (A) 6 to 32 Amp.cat III

Providing & erecting 240 V MCB double pole switch for Rupees Three

motor & inductive load (C Curve) having 10 KA breaking Hundred Thirty

162 capacity & confirms to IS : 8828 in existing box having Ea 2.00 330.27 and Paise

following capacity (B) 40 Amp. Twenty Seven

Providing & erecting 415 V MCB Four Pole for Motor & Rupees Three

Inductive Load (C Curve) having 10KA breaking capacity & Hundred Thirty

163 confirms to IS :8828 in existing box having following capacity Ea 3.00 330.27 and Paise

(a) 6 to 32 Amp. Cat.III Twenty Seven

Providing & erecting 415 V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking capacity &

164 confirms to IS :8828 in existing box having following capacity Ea 4.00 668.62

Eight and Paise

(b)40 Amp. Cat.III

Providing & erecting 415V MCB Four Pole Switch for

Lighting Load (B curve) having 10KA breaking capacity & Rupees Six

confirms to IS :8828 in existing box having following capacity Hundred Thirty

(b)40 Amp. Cat.III Eight and Paise

Thirty Two Only

Providing & erecting 415 V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking capacity &

166 confirms to IS :8828 in existing box having following capacity Ea 10.00 737.30

Seven and Paise

C) 63 Amp. CAT-III

Approved make ELCBs / RCCBs conforming to IS: 12640 and

having sensitivity of 30 mA and Short Circuit withstand

capacity of 6 KA and suitable for operation on single phase

240 V. having characteristic of quick action & tripping with

167 Ea 39.00 1969.50 Hundred Sixty

all advance feature & do not incorporate any electronic

component. for following Max. rating erected as directed

(i) 25 Amps.DP Cat. III

Approved make ELCBs / RCCBs conforming to IS: 12640 and

having sensitivity of 30 mA and Short Circuit withstand

capacity of 6 KA and suitable for operation on single phase

240 V. having characteristic of quick action & tripping with

168 Ea 30.00 1969.50 Hundred Sixty

all advance feature & do not incorporate any electronic

component. for following Max. rating erected as directed

(i) 40 Amps.DP Cat. III

Approved make ELCBs / RCCBs conforming to IS: 12640 and

having sensitivity of 30 mA and Short Circuit withstand Rupees Two

capacity of 6 KA and suitable for operation on single phase Thousand Six

240 V. having characteristic of quick action & tripping with Hundred Fifty

all advance feature & do not incorporate any electronic Four and Paise

component. for following Max. rating erected as directed Twenty Eight

(i) 63 Amps.DP Cat. III Only

JAJALUYA LED Par Lights 36 LED or approved equivalent Rupees

make Stage Lights 9 Modes RGB DJ Lights with Sound Nineteen

Activated Remote and DMX Control DJ Uplighting for Thousand Forty

Birthday Party Events Wedding Christmas Stage Lighting (4 Six and Paise

Packs) (Make should be approved by GMC) Ninety Four

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with

diffuser with company mark/name 160V to 270V, Power

Factor more than 0.9, THD < 15%, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED LED driver

171 Each 201.00 373.70 Seventy Three

efficiency > 85 % ( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown. (A)

Tube Light with integral driver (iv) 22-24 Watts, Surge -

2KV,IP-20, conventional 4 feet Cat III

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/aluminium pressure

die cast powder coated and high U.V. & corrosion

resistance with diffuser housed in aluminium casted body

with company mark/name 160V to 270V,Power Factor more Rupees Four

than 0.9, THD < 15 %,CCT 3000 K to 6500K, Luminaire Hundred

efficacy> 85 lumens/watt ,LED driver efficiency > 85 %( Twenty Seven

fitting required LM-79 & LM-80 Certificates)(NOTE: Below and Paise

description have shown ranges of Wattage capacity of LED Twenty Three

fittings.The Engineer incharge may select any wattage Only

capacity between the ranges shown.)(A) Square/ Circular

shaped Surface/Recessed Mount Downlight with provision

for spring loaded mounting clips complete.IP20 (ii) 11-15

watts, Surge-2 KV Cat-lll

(iv) 22-24 watts, Surge-2 KV Cat-lll

Eight and Paise

(I) Adjustable spot light with COB led having aluminium

reflector of following wattage (iv) 30 Watts

174 Each 180.00 2161.40 Hundred Sixty

Providing & fixing 35mm Surface Led profile Housing with

powder coating made from aluminium housing with Milky

acrylic cover with matt finished, Linear profile with 48 WATT

Tranquil LED STRIPS and driver suggested & as directed by

175 EIC/Consultant.and complete the work satisfactorily as per Mtr. 100.00 1937.99

Seven and Paise

instruction of architect or Engineer-in charge.(MODEL NO :

SL A015, BRAND SMART LUMINOUS OR EQUIVALENT

"Supply Installation Testing Commisioning of Indoor Office

Lighting 7-9w Recess Mounted Tiltable Spotlight

downlighter with below features

1.Pressure die cast Aluminum alloy housing for better

thermal conductivity.

2. With COb with Lens of 36-40 degree

3. Efficacy of Fixture more then or equal to 85 Lumens /watt

Available with 6500K,5700K, 4000K OR 3000K CCT.

4. CRI>80, High efficiency driver with inbuild surge

protection, over voltage protection, short circuit protection

176 Ea 30.00 833.25 Three and Paise

and operating at >0.9 PF. <5% THD

5. LED life of more then 35000 Hrs @ L70.

6. The product should be Manufactured in India (all the

Components should be manufactured in India except the

Led source which can be imported .(Approved Led source

Nichia , Cree, Lumileds , Osram Only)

Approved Make.: WIPRO/TISVA/HAVELLS/LIGHTING

TECHNOLOGIES/PHILIPS"

"Supply Installation Testing Commisioning of Indoor cove

1.) Strip should be mounted in Heavy 18X18mm corner

45degree customized Extruded Aluminium alloy CORNER

TYPE PROFILE with milky diffuser

2) Efficacy of Strip >=100 Lumens/Watt

3) Wattage of strip should be 12-15w/m. Should have a

dotless continuos effect. Available with 6500K,5700K, 4000K

OR 3000K CCT. Rupees Eight

4 ) Should be operated using remote driver of 24V Dc only, Hundred Fifty

kept at suitable locations for future maintainance. Three and Paise

5) Quantity are in running metres Forty Five Only

6) The product should be Manufactured in India (all the

Components should be manufactured in India except the

Led source which can be imported .(Approved Led source

Nichia , Cree, Lumileds , Osram Only)

Approved Make.: WIPRO/TISVA/HAVELLS/LIGHTING

TECHNOLOGIES/PHILIPS"

"Supply Installation Testing Commisioning of (bAFFLE

lIGHT) Indoor 30-34w Recessed Mounted 60mm Linear

office lighting of 1200mm length with below features

1) Cut out required 60mm.

2)The product should be Manufactured in India (all the

Components should be manufactured in India except the

Led source which can be imported) .

3) Available only in PCB option. Should be 4 feet length and

can be connected with polycarbonate diffuser profile for Rupees Three

continous decorative illumination Thousand Thirty

4) LED life of 50000 Hrs @ L70. IP20 Protection, Available Five and Paise

with 6500K,5700K, 4000K OR 3000K CCT. Five Only

5) should come with Anodised aluminium end caps firmly

fixed on the aluminium extrusion

6) should come with High end driver for better life and

Approved Make.: WIPRO/TISVA/HAVELLS/LIGHTING

TECHNOLOGIES/PHILIPS"

"Supply Installation Testing Commisioning of Outdoor

Architectural Post Top luminaire with Available system

Wattage 40W (± 5%) with System Efficacy not less than

75Lm/W, Diffused Optics with 360° Roto-Symmetric

Distribution, 100% DLOR ensuring No upwards light spilage,

Available in 3000K CCT, CRI>70, SDCM<5 , THD<5%, PF>0.9,

LED life 50,000 BHRS@L70, PDC Aluminium Alloy housing

for optmium thermal management, Clear UV Stabilized

Injection molded PC diffuser for wide distribution and non-

yellowing over the time, PCB Used for Making Light Engine

should be Metal Core PCB made of high grade Al 5052 with

minimum 70 micron copper thickness & 2 W/mk thermal

conductivity for better thermal maintanance for light

179 Engines. Corrosion resistant Nano technology power coating Ea 12.00 14847.00

of Silver Grey/Black Color/Terracota Red (As per selection

Seven and Paise

by Dept. or Architect) . Luminaire has a Ingress protection

of IP66 and Impact Resistance of IK08. Integral encapsulated

high efficiency electronic driver having a with rated voltage

of 140-270V, Inbuilt surge protection of 6 KV and upgraded

with integrated IP67 protected SPD of 20KV/10KA surge

protection with all necessary safety protection like mis-

wiring, Over voltage, Short circuit, Reverse Polarity

protection. Fixture is compatible for Pole with 76mm Dia.

IES, LM 79, LM 80, & TTC certificates will be provided from

NABL accredited lab.

Luminaire performance & Safety :IEC 60598, IS 10322-5, IS

Certification: CE Certified, Design Patented/Registered,

Supplying and erecting approved make Pole (Standard )

Made from HR sheet steel. The pole should be made as per

IS. and shall be coated with hot dip galvanizing as per IS

2629/2633/4759 with required base plate and integral

Junction box consist of terminal plate of min 6mm Hylam

sheet, standard profile 35mmX7.5mm Din-Rail for MCB

Mounting, stud type terminal and arrangement for cable

terminationas erected on suitable foundation (included)

180 Ea 20.00 15857.00 Hundred Fifty

with necessary nut-bolts/J-Bolts. as per details given by

Seven and Paise

manufacturer considering site requirement.Color finish of

the pole to be approved from the architect.

The length of poles are as below

(D) 4 Mtr. Long 65mm Top X155 mm bottom dia, 3mm

Providing & erecting Approved make Power Saving 50 Watt

Ceiling Fan with double ball bearing ISI mark with

Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete

181 having 3blades with aluminium blades with , canopy & 30 Each 8.00 1948.29

Eight and Paise

cm. down rod erected with earthing.(Make shall be

approved by Engineer in charge))

Supplying & erecting fan hook box of 10 mm M.S. round

bar bounded to the RCC bars up to 50mm length each side

182 and pierced through a 16 Gauge M.S. box / Heavy Duty PVC Each 8.00 108.07

and Paise Seven

box complete erected concealed in Ceiling with necessary

Supplying & erecting single phase approved make industrial

exhaust fan suitable for medium duty ring mounted low Rupees Three

noise operation suitable for medium duty having following Thousand Three

183 dia size and maximum speed in RPM [D] 450 mm dia 900 Each 6.00 3339.06 Hundred Thirty

RPM Cat.II Nine and Paise

Supplying and erecting approved make oscillating type

bracket fan A.C. 23OV. 50cy/s 400/450 mm sweep wall

mounted with height adjustment and rotary tilting device

184 Ea. 2.00 2534.09 Hundred Thirty

complete with guard, flexible Core plug top complete

erected with lead wires as directed. Cat.II

Providing & erecting weather proof, dust & vermin proof,

floor mounted front operated indoor type cubical panel

board necessary IP-42 and above protection as per

approval from engineer incharge made from 14 SWG thick

CRC M.S. sheet for outer body & doors, 16 SWG thick CRC

M.S.sheet for internal partitions with necessary accesories

supporting angles/ flats channel including cutting, bending,

drilling, welding, riveting with internal partitions & cable

alley as per requirements & instruction of engineer-in-

charge with erection of supplied switch gears, BUSBARS,

suitable size of inter connecting PVC copper wire / copper-

aluminium strips, rubber grommets, rib, bakelite control

fuses/MCB for measuring instruments, earth bus & earth

185 bolts, foundation flange - bolts-base Plates, sufficient nos. of Sq.Mtr 8.00 40999.94

hinged doors, handles with locking arrangement and rubber

gasket,heavy duty end terminal connection,danger notice

board,necessary ventilation,earthing strip complete. The

Panel shall be painted with epoxy powder coating.(The rates

excludes the cost of switchgears, bus bars, inter connecting

mains & Copper Aluminium strips, meters, Fuses etc. The

dimension shall be measured excluding base beams) The

panel shall be supplied with following approved

manufacturers with following size.

(B) The standard companies switch gear shall be used and

only manufacturers at CPRI approved factory

(iv) with 1000 mm. depth

Providing & erecting weather proof, dust & vermin proof,

floor mounted front operated indoor type cubical panel

board necessary IP-42 and above protection as per

approval from engineer incharge made from 14 SWG thick

CRC M.S. sheet for outer body & doors, 16 SWG thick CRC

M.S.sheet for internal partitions with necessary accesories

supporting angles/ flats channel including cutting, bending,

drilling, welding, riveting with internal partitions & cable

alley as per requirements & instruction of engineer-in-

charge with erection of supplied switch gears, BUSBARS,

suitable size of inter connecting PVC copper wire / copper-

aluminium strips, rubber grommets, rib, bakelite control

fuses/MCB for measuring instruments, earth bus & earth

186 bolts, foundation flange - bolts-base Plates, sufficient nos. of Sq.Mtr 8.00 19387.96

hinged doors, handles with locking arrangement and rubber

Seven and Paise

gasket,heavy duty end terminal connection,danger notice

Ninety Six Only

board,necessary ventilation,earthing strip complete. The

Panel shall be painted with epoxy powder coating.(The rates

excludes the cost of switchgears, bus bars, inter connecting

mains & Copper Aluminium strips, meters, Fuses etc. The

dimension shall be measured excluding base beams) The

panel shall be supplied with following approved

manufacturers with following size.

(B) The standard companies switch gear shall be used and

only manufacturers at CPRI approved factory

(ii) with 550 mm. Depth

Providing & erecting weather proof, dust & vermin proof,

floor mounted front operated indoor type cubical panel

board necessary IP-42 and above protection as per

approval from engineer incharge made from 14 SWG thick

CRC M.S. sheet for outer body & doors, 16 SWG thick CRC

M.S.sheet for internal partitions with necessary accesories

supporting angles/ flats channel including cutting, bending,

drilling, welding, riveting with internal partitions & cable

alley as per requirements & instruction of engineer-in-

charge with erection of supplied switch gears, BUSBARS,

suitable size of inter connecting PVC copper wire / copper-

aluminium strips, rubber grommets, rib, bakelite control

fuses/MCB for measuring instruments, earth bus & earth

187 bolts, foundation flange - bolts-base Plates, sufficient nos. of Sq.Mtr 10.00 14902.55

hinged doors, handles with locking arrangement and rubber

and Paise Fifty

gasket,heavy duty end terminal connection,danger notice

board,necessary ventilation,earthing strip complete. The

Panel shall be painted with epoxy powder coating.(The rates

excludes the cost of switchgears, bus bars, inter connecting

mains & Copper Aluminium strips, meters, Fuses etc. The

dimension shall be measured excluding base beams) The

panel shall be supplied with following approved

manufacturers with following size.

(B) The standard companies switch gear shall be used and

only manufacturers at CPRI approved factory

(i) with 350mm depth

Providing and erecting Approved make Four pole moulded

case circuit breaker having breaking capacity ICU of 50 KA Rupees Twenty

and above at 415 V having Normal current rating 400A. Five Thousand

with variable Thermal & magnetic release suitable to work Two Hundred

188 on A.C.supply 50 c/s. With all internal connections, spreader Ea. 1.00 25228.79 Twenty Eight

tinned copper & complete erected in existing 16 G.M.S. and Paise

housing. ICS=100% of ICU only Cat III ( DG & GEB Seventy Nine

INCOMING IN PANEL) Only

Providing and erecting Approved make Four pole moulded

case circuit breaker having breaking capacity ICU of 35 KA.

at 415 V. having Normal current rating 200A.with variable

Thermal & magnetic release suitable to work on A.C.supply

189 50 c/s. with all internal connections, spreader tinned copper Ea. 6.00 16221.61

& complete erected in existing 16 G.M.S.housing ICS=100%

Paise Sixty One

of ICU only Cat III ( 2 AHU PANEL & 4 CONDENSER PANEL)

providing and erecting Approved make Four pole moulded

case circuit breaker having breaking capacity ICU of 25 KA.

at 415 V,having normal current rating up to 25 A to 100A.

with Fixed thermal & magnetic release suitable to work on

190 A.C. supply 50 c/s. with all internal connections, spreader Ea. 16.00 6173.12

tinned copper & complete erected in existing 16 G.M.S.

housing. ICS=100% of ICU only Cat III (100A) (3

INCOMING IN TPN DB + PUMP + 2 SPARE )

Supplying & erecting approved make Four Pole 415V change

over switch interior for panel mounting with operating

mechanism A.C.23 duty confirming to IS for

Paise Thirty Five

Supplying & erecting approved make Four Pole 415V change

over switch interior for panel mounting with operating Rupees Twenty

mechanism A.C.23 duty confirming to IS for Six Thousand

(H) 800 A Cat. III One Hundred

Supplying and erecting triple pole & neutral 440V/ 500V

panel mounting Aluminium Busbars with four equal Nos. of

bus having current density not more than 0.8 Amp. / sq.mm

(Rated current / cross section area) duly wrapped with

colour insulating tape for phase sequence of following

193 current carrying capacity, erected with necessary bus bar Rn.Mtr 3.00 3061.31

supports /insulators, main cable socket to each

Thirty One Only

busbar,erected in existing cubical panel with necessary

connections.(E) Suitable for 630 Amp. capacity

Supplying and erecting triple pole & neutral 440V/ 500V

panel mounting Aluminium Busbars with four equal Nos. of

bus having current density not more than 0.8 Amp. / sq.mm

(Rated current / cross section area) duly wrapped with Rupees Two

colour insulating tape for phase sequence of following Thousand Two

194 current carrying capacity, erected with necessary bus bar Rn.Mtr 3.00 2204.83 Hundred Four

supports /insulators, main cable socket to each and Paise Eighty

busbar,erected in existing cubical panel with necessary Three Only

connections. (D) Suitable for 400 Amp. Capacity

Providing & erecting L.T. Current Transformer with bar Rupees Two

primary 50/5 to 1000/5 ratio 15 VA burden erected in Hundred

existing CRCA box duly secured with insulating materials Seventy Four

connected to the meter (make: havells , L & T , Simens , and Paise

legrand , ABB,Hager) ( FOR METERING) Seventy Two

Supplying and erecting approved make suitable panel Rupees Forty

indicator LED type lamp, lens cover, complete erected wAith Three and Paise

necessary connections. Forty Three

providing and erecting Approved make Earth fault Relay

suitable to mount with inter connection suitable to

following size of moulded case circuit breaker having CT Rupees Five

ratio & MCCB rating as following along with shunt trip 220V Thousand Four

197 AC. with all internal connections & complete erected in Ea. 1.00 5415.62 Hundred Fifteen

existing M.S.housing.. (3) 250 A -400 A , CT Ratio 1/400 and Paise Sixty

(make: havells , L & T , Simens , legrand , ABB,Hager) (FOR Two Only

FAULT PROTECTION IN PANEL)

Supplying and erecting approved make panel mounting type

Digital Voltmeter having 3 digits LED display, 0 to 750 AC

Volts range erected on existing panel board with all

198 connection, wiring etc .with manufacturers calibration Ea. 6.00 1275.63

certificate.(make: havells , L & T , Simens , legrand

and Paise Sixty

ABB,Hager) (1 for ac panel, 1 for main panel)

Supplying and erecting approved make panel mounting type

Digital Ammeter having 3 digits LED display, external CT Rupees One

operated, calibrated for 0 to 1000 Amps suitable to operate Thousand Five

on 500 Volt AC , erected on existing panel board with all Hundred Fifty

connection, wiring etc .with manufacturers calibration Eight and Paise

certificate.(make: havells , L & T , Simens , legrand , Forty Three

ABB,Hager) (1 for ac panel, 1 for main panel) Only

Providing and erecting Approved make RCCBs conforming to

IS: 12640 and having sensitivity of 300 mA and Short Circuit

withstand capacity of 10 KA and suitable for operation on 3 Rupees One

phase and neutral 415V,50Hz. having characteristic of quick Thousand Nine

200 action & tripping with all advance feature & do not Each 6.00 1969.50 Hundred Sixty

incorporate any electronic component for following Max. Nine and Paise

rating erected as directed. (i) 25 Amps.DP Cat. III Fifty Only

Supplying and erecting triple pole & neutral 440V/ 500V

panel mounting Aluminium Busbars with four equal Nos. of

bus having current density not more than 0.8 Amp. / sq.mm

(Rated current / cross section area) duly wrapped with

colour insulating tape for phase sequence of following

201 current carrying capacity, erected with necessary bus bar Rn.Mtr 2.00 660.54

and Paise Fifty

supports /insulators, main cable socket to each

busbar,erected in existing cubical panel with necessary

connections.(A) Suitable for 100 Amp. Capacity ( IN PANEL )

Providing & erecting 415 V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking capacity &

202 confirms to IS :8828 in existing box having following capacity Each 10.00 737.30

Seven and Paise

(c)63 Amp. Cat.III ( 3 DB INCOMING )

Providing & erecting 415V MCB Four Pole Switch for Rupees Five

Lighting Load (B curve) having 10KA breaking capacity & Hundred

confirms to IS :8828 in existing box having following capacity Seventy Eight

(a) 6 to 32 Amp. Cat.III (For Metal halide) and Paise

Providing and erecting Sheet Steel powder coated Vertical

MCB distribution board (VTPN) - flush / surface mounted

double door (IP54) fitted with copper insulated busbar,

isolated neutral bar, earth bar and DIN rail, Conforms to IS

204 8623-1 & 3, IEC 61439-1 & 3, suitable for 250 AMP TPN Ea 3.00 9921.23

MCCB + RCCB as incomer and three phase outgoing as per

following .(The DBs should be used of same company of

MCB to be used) (B)6 way outgoing

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS Rupees Three

8623-1 & 3, IEC 61439-1 & 3 without MCB to house Thousand Four

appropriate nos. of MCBs.(The DBs should be used of same Hundred Twelve

company of MCB to be used) suitable for (B) three phase and Paise

incoming and single phase horizontal type outgoing Per Seventy Nine

phase isolation type (PPI)(b) sheet steel double door(iii)8 Only

way ( LIGHT POWER ) (TPN DB)

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS Rupees One

8623-1 & 3, IEC 61439-1 & 3 without MCB to house Thousand Four

appropriate nos. of MCBs.(The DBs should be used of same Hundred Ninety

company of MCB to be used) suitable for (A) single phase Two and Paise

incoming and horizontal single phase outgoing (b) sheet Seventy Eight

steel double door (IP-43) (iv)12 way ( LIGHT POWER ) (SPN Only

providing and erecting Miniature circuit breaker single pole

6A to 25A suitable to operate on 240 V A.C. system and Rupees One

having breaking capacity 10 KA to be erected in existing Hundred Twelve

box. confirming to IS 8828/1996 with ISI Mark Cat.III (10 and Paise

STREET LIGHT, 30 TPN DB, 32 SPDB) Eleven Only

Providing & erecting 240 V MCB double pole switch for

lighting Load (B Curve) having 10 KA breaking capacity &

confirms to IS : 8828 in existing box having following

208 Each 8.00 278.76 Seventy Eight

capacity (A) 6 to 32 Amp. Cat.III ( 4 IN SPN DB, 9 IN TPN DB

Seventy Six Only

providing and erecting Approved make RCCBs conforming to

IS: 12640 and having sensitivity of 30 mA and Short Circuit

withstand capacity of 10 KA and suitable for operation on Rupees Two

single phase 240 V,50Hz. having characteristic of quick Thousand Six

209 action & tripping with all advance feature & do not Each 6.00 2637.11 Hundred Thirty

incorporate any electronic component. for following Max. Seven and Paise

rating erected as directed (ii) 40Amps. DP Cat. III ( 3 IN Eleven Only

TPN DB, 4 IN SPN DB )

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand / Solid Copper conductor for 1.1 KV. to Rupees Five

be laid on wall with necessary clamps or in existing trench Hundred Eight

/ pipe at road crossing or floor of following size of cables. and Paise Three

(C) 4 core 6 Sq. mm (For street light) Only

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Copper conductor for 1.1 KV. to be laid

on wall with necessary clamps or in existing trench / pipe

211 Mtr. 40.00 673.67 Seventy Three

at road crossing or floor of following size of cables. (A)

and Paise Sixty

core 10 Sq. (FOR 12 WAY SPN DB)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

212 Mtr. 150.00 217.15 Seventeen and

pipe of following size of cables (B) 3 1/2 core 35 Sq. mm (

25 Sq.1/2 mm core) ( 12 WAY TPN DB)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

213 Mtr 180.00 281.79 One and Paise

pipe of following size of cables (C) 3 1/2 core 50 Sq. mm (

25 Sq.1/2 mm core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

214 Mtr 500.00 899.91 Nine and Paise

pipe of following size of cables (H) 3 1/2 core 185 Sq. mm (

95 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

215 Mtr 700.00 1161.50 Hundred Sixty

pipe of following size of cables (I) 3 1/2 core 240 Sq. mm(

120 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

216 Mtr 300.00 1400.87 Hundred and

pipe of following size of cables (J) 3 1/2 core 300 Sq.mm (

150 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured Rupees Two

cable multistrand Copper conductor for 1.1 KV. to be laid Hundred

217 on wall with necessary clamps or in existing trench / pipe Mtr 1200.00 213.11 Thirteen and

at road crossing or floor of following size of cable. (A) 3 core Paise Eleven

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Copper conductor for 1.1 KV. to be laid

on wall with necessary clamps or in existing trench / pipe

218 Mtr 950.00 285.83 Five and Paise

at road crossing or floor of following size of cable.(B) 3 core

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be

219 laid on wall with necessary clamps or in existing trench / Mtr 2500.00 151.50

pipe of following size of cables (A) 4 core 16 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

220 Mtr 450.00 188.87 Eight and Paise

pipe of following size of cables (B) 4 core 25 Sq. mm

Providing and, fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured cable

Three and Paise

221 complete with out going tails, insulating tape etc for Ea 50.00 33.33

following size of cables. (A) 2 to 4 core 2.5 / 4 Sq. mm

Providing and, fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured cable

Seven and Paise

222 complete with out going tails, insulating tape etc for Ea 50.00 47.47

following size of cables. (D) 2 to 4 core 16 Sq. mm

Providing and, fixing heavy duty flange type brass double

compression type cable gland with rubber ring for PVC Rupees Sixty Six

223 insulated armoured cable complete with out going tails, Ea 20.00 66.66 and Paise Sixty

insulating tape etc for following size of cables. (A) 3 & 1/2 / Six Only

4 core 25 Sq. mm

Providing and, fixing heavy duty flange type brass double

compression type cable gland with rubber ring for PVC

224 insulated armoured cable complete with out going tails, Ea 10.00 75.75

insulating tape etc for following size of cables.(B) 3 & 1/2

core 35/50 Sq. mm

Providing and, fixing heavy duty flange type brass double

compression type cable gland with rubber ring for PVC Rupees Two

insulated armoured cable complete with out going tails, Hundred Thirty

insulating tape etc for following size of cables.(G) 3 & 1/2 Eight and Paise

core 185 Sq. mm Thirty Six Only

Providing and, fixing heavy duty flange type brass double

compression type cable gland with rubber ring for PVC Rupees Two

insulated armoured cable complete with out going tails, Hundred Forty

insulating tape etc for following size of cables .(H) 3 & 1/2 Seven and Paise

core 240 Sq. mm Forty Five Only

Providing and, fixing heavy duty flange type brass double Rupees Two

compression type cable gland with rubber ring for PVC Hundred Eighty

227 insulated armoured cable complete with out going tails, Ea 18.00 280.78 and Paise

insulating tape etc for following size of cables.(I) 3 & 1/2 Seventy Eight

core 300 Sq. mm Only

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with Rupees Six and

brass/cadmium plated nut bolts in an approved manner. (A) Paise Six Only

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high Rupees Fifteen

229 pressure tool & connected to switchgear terminals with Ea 290.00 15.15 and Paise

brass/cadmium plated nut bolts in an approved manner. Fifteen Only

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high Rupees Twenty

230 pressure tool & connected to switchgear terminals with Ea 24.00 20.20 and Paise

brass/cadmium plated nut bolts in an approved manner. Twenty Only

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high Rupees Eighty

231 pressure tool & connected to switchgear terminals with Ea 56.00 80.80 and Paise Eighty

brass/cadmium plated nut bolts in an approved manner. Only

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high Rupees Eighty

232 pressure tool & connected to switchgear terminals with Ea 32.00 85.85 Five and Paise

brass/cadmium plated nut bolts in an approved manner.(J) Eighty Five Only

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high Rupees Eighty

233 pressure tool & connected to switchgear terminals with Ea 72.00 85.85 Five and Paise

brass/cadmium plated nut bolts in an approved manner. Eighty Five Only

Providing and fixing approved make Ladder type cable tray.

Made from M.S sheet. The cable tray should be bended as

per IS 2062/1079 shall be fabricated of double bended

channel section longitudinal members with single bended

Channel section. Rungs of members welded to the base of Rupees Two

the longitudinal members at 250 mm c/c spacing . as per IS Hundred

234 and shall be coated with hot dip galvanizing as per IS Mtr 250.00 278.76 Seventy Eight

2629/4759. with coupler plate / Fish plate and GI hardware and Paise

like nut - bolt and washers etc. erected on existing support Seventy Six Only

as per Specification and as per instruction of engineer in

charge.(1) 150 X 50 X 1.6 mm Thick.

Providing and fixing approved make Ladder type cable tray.

Made from M.S sheet. The cable tray should be bended as

per IS 2062/1079 shall be fabricated of double bended

channel section longitudinal members with single bended

Channel section. Rungs of members welded to the base of

the longitudinal members at 250 mm c/c spacing . as per IS

235 and shall be coated with hot dip galvanizing as per IS Mtr 80.00 287.85

Seven and Paise

2629/4759. with coupler plate / Fish plate and GI hardware

Eighty Five Only

like nut - bolt and washers etc. erected on existing support

as per Specification and as per instruction of engineer in

charge..(2) 200 X 50 X 1.6 mm Thick

Providing and fixing approved make Perforated C type cable

tray. Made from sheet steel. The cable tray should be

single or double bended as per required and as per IS

2062/1079 and shall be coated with hot dip galvanizing as Rupees Three

per IS 2629/4759. with max 17.5% perforation with coupler Hundred Nine

plate / Fish plate and GI hardware like nut - bolt and and Paise Six

washers etc. erection with necessary support( included) as Only

per Specification and as per instruction of engineer in

charge.. (3)300 X 50 X 1.6 mm Thick

Providing and fixing approved make Ladder type cable tray.

Made from M.S sheet. The cable tray should be bended as

per IS 2062/1079 shall be fabricated of double bended

channel section longitudinal members with single bended

Channel section. Rungs of members welded to the base of Rupees Six

the longitudinal members at 250 mm c/c spacing . as per IS Hundred Ninety

237 and shall be coated with hot dip galvanizing as per IS Mtr 60.00 694.88 Four and Paise

2629/4759. with coupler plate / Fish plate and GI hardware Eighty Eight

like nut - bolt and washers etc. erected on existing support Only

as per Specification and as per instruction of engineer in

charge..(6) 600 X 50 X 2.0 mm Thick

Providing and fixing approved make Ladder type cable tray.

Made from M.S sheet. The cable tray should be bended as

per IS 2062/1079 shall be fabricated of double bended

channel section longitudinal members with single bended

Channel section. Rungs of members welded to the base of Rupees Eight

the longitudinal members at 250 mm c/c spacing . as per IS Hundred

238 and shall be coated with hot dip galvanizing as per IS Mtr 130.00 874.66 Seventy Four

2629/4759. with coupler plate / Fish plate and GI hardware and Paise Sixty

like nut - bolt and washers etc. erected on existing support Six Only

as per Specification and as per instruction of engineer in

charge..(16) 900 X 100 X 2.0 mm Thick

Providing and fixing approved make Perforated C type cable

tray. Made from pre- galvanized sheet steel. The cable tray

should be bended as per IS 2062/1079 . with max 17.5%

perforation with coupler plate / Fish plate and GI hardware

239 Mtr 300.00 322.19 Twenty Two

like nut - bolt and washers etc. erected on existing support

as per Specification and as per instruction of engineer in

charge..(3) 150 X 50 X 1.5 mm Thick

Providing and fixing approved make Perforated C type cable

tray. Made from pre- galvanized sheet steel. The cable tray

should be bended as per IS 2062/1079 . with max 17.5% Rupees Four

perforation with coupler plate / Fish plate and GI hardware Hundred

240 like nut - bolt and washers etc. erected on existing support Mtr 300.00 471.67 Seventy One

as per Specification and as per instruction of engineer in and Paise Sixty

charge..(3) 150 X 50 X 1.5 mm Thick (5) 300 X 50 X 1.5 mm Seven Only

Supplying under floor pregalvanised corrosion proof

rectangular sheet steel cable trunking of 1.6 mm thick

having with stand point load up to 1.33 Ton & free from

seepage of concrete of screed water with all Rupees Seven

accessories,Junction Box,Joints as required and demanded Hundred Thirty

241 by engineer-incharge and laying/erecting as per OEM Mtr 200.00 731.24 One and Paise

guidelines and as per instruction of engineer incharge Twenty Four

having following size of dimensions and No of Only

compartments (W x D x T) Cat-III [10] 150mm x 38mm x

1.6mm with Three Compartments

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand / Solid Copper conductor for 1.1 KV. to Rupees Two

be laid on wall with necessary clamps or in existing trench Hundred Sixty

/ pipe at road crossing or floor of following size of cables. Nine and Paise

(A) 4 core 2.5 Sq. mm (for metal helide) Sixty Seven Only

Providing and, fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured cable

Eight and Paise

243 complete with out going tails, insulating tape etc for Ea. 15.00 38.38

following size of cables. (B) 2 to 4 core 6 Sq. mm

Providing and, fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured cable

Eight and Paise

244 complete with out going tails, insulating tape etc for Ea. 21.00 38.38

following size of cables. (C) 2 to 4 core 10 Sq. mm

Providing and, fixing heavy duty flange type brass double

compression type cable gland with rubber ring for PVC

245 insulated armoured cable complete with out going tails, Ea. 9.00 75.75

insulating tape etc for following size of cables. (B) 3 & 1/2

core 35/50 Sq. mm

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high Rupees Thirteen

246 pressure tool & connected to switchgear terminals with Ea. 80.00 13.13 and Paise

brass/cadmium plated nut bolts in an approved manner. (B) Thirteen Only

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high Rupees Twenty

247 pressure tool & connected to switchgear terminals with Ea. 21.00 20.20 and Paise

brass/cadmium plated nut bolts in an approved manner. (D) Twenty Only

Supply, Installation, Testing and Comissioning of 4MP Fixed

Lens Dome Type Camera,

H.265 4MP IR Vandal Proof Dome N/W Camera,

2.8mm/3.6mm, 30M IR, Micro SD, DC12V/PoE, IP67/IK10,

Basic IVA, 1 / 2.7" CMOS, 2560 × 1440, 0.01 Lux, F1.2, AGC

248 ON; Defog, True day/night, Digital WDR, 3D DNR, HLC & Each 25.00 8170.90

BLC, Triple streams, Smart codec by ROI, Cyber Security,

Basic intelligent video analytics, NDAA Compliance, UL, CE,

FCC Certified (Including Five year free maintenance with

Supply, Installation, Testing & Commissioning of outdoor

MP IP Bullet Camera of 1/2.8" Progressive CMOS Sensor

with resolution 30 fps @ FHD & Manual Vari Focal f = 3-

mm Field of View 40° ~ 80° (H), 30° ~ 60° (V) IR range upto

30 Mtr Smart IR Min. Illumination 0.1 Lux @ F1.4 (Color),

249 0.01 Lux @ F1.4 (B/W) Noise Reduction ; Compression Each 10.00 5474.20

Technology H.265, H.264, MJPEG with 3 simultaneous

streams ;P-iris Lens & Digital Image Stabilization ; ONVIF

IP43, CE, FCC Class A, UL listed with all required

Supplying & erecting Galvanized M.S pipe post “B” class Rupees Four

88.9 mm O.D 6 mtr. Long duly painted with two coats of Thousand Four

aluminium paint complete with metallic base- plate of 300 Hundred Forty

mm x 300 mm x 4mm thick for using as a compound light and Paise

pole with approx. weight 47 Kg. Ninety Seven

Supply, Installation, Testing and Comissioning of 32 Channel

Network Video Recorder (NVR), Support 8CH@2MP, H.264

Rupees Fifty Six

Video Compression, HDMI, VGA output, up to 4 SATA

interface each with max 6 TB support, bandwidth 200 mbps,

251 Each 1.00 56411.19 Hundred Eleven

CE FCC, BIS, Operating Temp -10 deg to 50 deg C, USB and

serial Interface (Including Five year free maintenance with

Supply, Installation, Testing and Comissioning of 6TB

Survaillance grade HDD having 30 days of recording storage Rupees Thirteen

capacity Thousand Two

252 Each 3.00 13251.20 Hundred Fifty

Supply, Installation, Testing and Comissioning of 65" Smart

4K Non-Touch display | In-built Android 8.0, RAM 3 GB,

GB ROM| 20W x 2 Speakers | 6 no. of Beam Forming

Microphones with Echo Cancellation | 50000 Hours of Life |

253 500 nits Brightness| Multiple Inputs for connectivity | Each 1.00 192274.91

Inbuilt Screen Sharing Software | Slimmer Frame |OPS Slot

for On-Board Computer Connectivity (Including Five year

free maintenance with guarantee)

Supply, Installation, Testing and Commissioning of a Wall

Mounting Bracket for Panel

254 Each 1.00 3865.21 Hundred Sixty

Supply, Installation, Testing and Commissioning of CCTV

management work station i7-11700 (8 core)/ 2x8GB

Memory/1xIntel 512 Gb NVME SSD/1x1TB 7.2 SATA

255 HDD/Win 10 Pro(OEM)/24" Monitor/DVDRW/3 Yrs Each 1.00 140241.59

Fifty Nine Only

Supply,Installation,Testing and Commissioning of 12 ft HDMI

Interface Cable Should be 12ft Male to Male High-speed Rupees Seven

Category 2 HDMI cable; Should be 24k gold-plated 19-pin Thousand One

Type A connector; Should have High-flex CL3-rated jacket; Hundred

Should Support 4K60 4:4:4 video; Should support 18 Gbps Twenty Two

bandwidth; Should be RoHS compliant (Including Five year and Paise Fifty

free maintenance with guarantee) Two Only

Supplying & erecting approved make LAN cable of following

size in existing pipe as per direction [E] CAT - 6 shielded

257 Mtr 900.00 90.90 and Paise

Back Box with IO at camera side

Fifty Five Only

Providing & erecting PVC Corrugated Flexible Conduit with

required nos. of coupling, PVC bushes, Check-nuts etc.

259 Mtr 80.00 20.20 and Paise

complete of following sizes. (2) 25 mm

Supply, Installation, Testing and Commissioning of Rack 12U

260 Nos 2.00 11594.80 Hundred Ninety

Supply, Installation, Testing and Commissioning of CAT6 UTP

23AWG Solid: Per Meter (Including Five year free

261 Mtrs. 3000.00 60.46 and Paise Forty

maintenance with guarantee)

Supply, Installation, Testing and Commissioning of Patch

Panel Cat 6 UTP Keystone Type- 24 Port-Fully Loaded

(Including Five year free maintenance with guarantee)

262 Nos 4.00 6450.02 Hundred Fifty

Supply, Installation, Testing and Commissioning of Jack Cat

Keystone UTP (Including Five year free maintenance with

263 Nos 65.00 234.38 Four and Paise

Supply, Installation, Testing and Commissioning of CAT6 UTP

24AWG PATCH CORD:1M,Plug 30U' Snag less (Including

Five year free maintenance with guarantee)

264 Nos 65.00 228.58 Twenty Eight

and Paise Fifty

Supply, Installation, Testing and Commissioning of CAT6 UTP

24AWG PATCH CORD:2M,Plug 30U' Snag less (Including

265 Five year free maintenance with guarantee) Nos 65.00 293.18

Three and Paise

Supply, Installation, Testing and Comissioning of Face Plate -

Single (Keystone Jack,square) (Including Five year free Rupees One

maintenance with guarantee) Hundred Thirty

Sixty Eight Only

Supply, Installation, Testing and Commissioning of 25MM

267 Mtr. 1300.00 47.21 Seven and Paise

Supply, Installation, Testing and Commissioning of 32MM Rupees Thirty

Flexible Pipe Nine and Paise

Supply, Installation, Testing and Commissioning of trunkinng Rupees Three

Casing Caping 100X50 Hundred Eighty

269 Mtr. 10.00 380.97 and Paise

Supply, Installation, Testing and Commissioning of

Wheather Proof Back Box for CCTV(120X120X75)

270 Nos 20.00 192.97 Two and Paise

Supply, Installation, Testing and Commissioning of 24 x

10/100/1000 PoE+ ports with 384W power budget, 4 x

Gigabit SFP, Rack-mountable

Supply, Installation, Testing and Commissioning of Insight

Managed WiFi 6 4X4 Dual Band High Performance WiFi 6 Rupees Twenty

Access Points Nine Thousand

272 Nos 5.00 29440.03 Four Hundred

Forty and Paise

Supply, Installation, Testing and Commissioning of Cloud

Based Controller Insight Pro - subscription license (3 years) -

1 managed device

(A) GENERAL DESCRIPTION OF LIFTS.

[1] GEAR LESS LIFT DRIVE (MRL) comprising of High Starting

torque Lift 3 phase 440 V A. C. Permanent Magnet

Synchronous motor of proper rating with high efficiency

shall be used.[2] Micro processor based / PLC, ACVVVF,

vector control drive with encoder feedback closed loop

system shall be used for lift car and door operation which

shall be full collective selective operation hall call demand

response, UP/DOWN hall stops, Main, Up/ Down Contactor

with overload and phase reversal relay and safety controls.

[3] Car with M S platform with bracings of adequate size and

to sustain the impact load cabin + passenger with safety

factor of fire for steel and side panels of Stainless steel of

sheet of grade 304 duty. Car ceiling will be S.S. finishes with

aesthetic appearance with LED ceiling lights. Car flooring

shall be of anti skid PVC with choice of colour of engineer in

charge. Car doors shall be of stainless steel grade

hairline finish with centre opening / telescopic automatic

doors. Car panel will also be S.S. 304 finished with

emergency stop device, mechanical door safety device,

facility of auto/ attended mode. All car panel buttons and all

floor switches must be with brail language as per lift act.

[4] All landing doors must be fire rated for 2 hour shall be

fully automatic centre opening/ telescopic opening made of

hairline finish steel grade of 304 with key holes and infrared

curtains with Unlocking facility from outside

[5] Appropriate battery operated emergency light in the car

along with alarm switch shall be provided. Also, Emergency

Light & Fan should start immediately without any Time

Delay as soon as power fails.

[6] Digital scrolling indicator system for up-down arrow

along with floor position indicator shall be provided inside

the car and at all floors.

[7] Full height infra red curtain with multiple cross / crossing

light beams shall be provided.[8] Automatic Rescue Device

(ARD) shall be provided accordingly of passenger capacity

with Manual Rescue Operation ( Manual Cranking Facility).

[9] Audio visual indication in the lift car showing over

loading shall be provided such that doors kept open till

excess load is removed.

[10] Spring buffers/PU Buffers shall be provided.

[11] Car fan as per passenger capacity with automatic sleep

timer shall be provided.

[12] Voice annunciator with suitable music shall be provided Rupees Ten

in lift car. Lakhs Thirty

[13] Self diagnostics system for operational and safety Nine Thousand

274 parameters shall be provided in control panel. Ea 1.00 1039957.61 Nine Hundred

[14] Mechanical over speed governor with governor Fifty Seven and

calibration as per actual site parameters and submission of Paise Sixty One

calibration certificate submission, door key holes in the floor Only

doors, fireman switch shall be provided.

[15] Lift machine hoisting arrangement in the lift machine

room and monkey ladder for lift pit should be provided by

the lift agency, along with the other steel structure works,

foundations for the machine etc…

[16] In the hoist way fascia plate shall be provided without

any extra cost, where ever required as / if directed by

engineer in charge.

[17] Permanent wiring with necessary safety devices like

RCCB in all circuit, Over Voltage Under Voltage protection

and THD eliminator in circuit for lift machine room and lift

well with proper numbers of light points, with fixtures,

exhaust fan and plug points shall be provided by the agency.

Only 3 phase Power Supply shall be made available by

department in lift machine room. Necessary Earthing as per

Lift Act/Rules shall be arranged by Lift Agency.

[18] Any civil/ electrical works for additional and alteration

in lift shaft and machine room related to erection of lift shall

be made by lift agency without any extra cost.

(granite/marble fixing around all landing door openings are

not in lift agency’s scope.)

[19] Agency has to provide all working drawings and

documents and liaison services for obtaining all necessary

permission from lift inspector and other authorities.

[20] acrylic transparent licence/display A4 size holder in lift

[20A] As per statutory requirement of Govt. Of Gujarat lift &

escalator act 2000, lift agency has to provide

1. Car top safety barricade

2. Push & talk communication system.

3. Fireman's switch operation at Ground Floor.

4.carrying out third party lift inspection during/after lift

erection and provide report by third party authorized by

concern licensing authority 5.agency has to provide third

party insurance upto completion of free maintenance

period and submit the document for the same.

[21] Car Panel Operating Buttons with floor position

indicator/buttons must be of Auto Glow type clearly visible

when view from inside cabin.

[22] For Physically Handicapped person Full Length

Handrails of hairline finish steel grade of 304 should be

provided at appropriate height on the Rear & Side Wall

Panels in Lift Car.

Supplying and erecting, commissioning and testing of Diesel

Generating set confirming to IS: 4722:1968 & BS:5514

having continuous rating, 3 phase, 415 volts, 50 cycles A.C.

supply comprising of a totally enclosed air/water cooled

diesel engine with multi-cylinders developing suitable BHP

not less than following capacity at 1500 RPM with 10%

overload for one hour in 24 hours with standard accessories

like fly wheel, lubricating oil cooler, "A" class governor,

heavy duty fuel wheel and lubricating oil filter, oil bath air

filler, lubricating oil pressure gauge, end exhaust manifold,

standard set of tools with adjustable spanners, screw

drivers, cylinder head to cover, joint cylinder head to

exhaust, element lube oil filter, 12 / 24 volts electric starting

equipment complete with standard heavy duty battery,

dynamo, cut-outs, ammeter, necessary wiring, pressure

gauge, starter etc and heavy duty Residential type exhaust

silencer and vertical hot air duct both

Two Lakhs Forty

Thirty Two Only

logged with asbestos rope, save oil trays, exhaust piping of

required length, standard wall/floor mounted fuel with level

indicator and piping and drip proof alternator, self excited,

self regulated, screen protected, with excitation system,

capable of delivering the rated system output at 415 volts,

phase, 0.8 PF, 50 Hz, 4 wire, running at 1500 RPM, Rupees Thirty

conforming to IS-4722- 1968 with voltage regulation +/- Two Lakhs Forty

5% of rated voltage from no load to full load. Both the Nine Thousand

engine and alternator fitted on a common fabricated steel Five Hundred

base plate with antivibration mounting engine and Five and Paise

alternator both connected to each other by flexible flange Thirty Two Only

coupling and with floor/wall mounted control panel box

comprising of voltmeter ammeter, selector switches, ACB

/ MCCB / MCB of adequate capacity,

indicator lamps duly wired with HRC fuses. The alternator &

control panel shall be connected with provided suitable

capacity armoured cable and complete with Acoustic

enclosure (canopy) made out of 16 SWG CRCA Sheet, sound

absorbing material Rockwool of 64 density & 100 mm thick

conforming to IS:8183 / PU Foam of 40 Density - at least

mm. The resin bonded rockwool covered from inside the

canopy by perforated sheet with 3/4 mm holes, sound level

not more than 75 dB at a distance of 1 mtr, as per PVCT

norms. Erection, commissioning and satisfactory testing as

per requirement with first filling of fuel, oil, etc. with

guarantee / Warrantee of complete system for Two years. &

with obtaining all necessary certificate from Electrical

Inspector. The Capacity and Ratings of DG sets are as below

with latest CPCB norms

(V) Continuous rating of 500 KVA ,BHP not less than

Providing & erecting approved make AMF control panel

suitable for following size of 3 phase, 415 V., 50 cycles, A.C.

diesel generating set complete of scope as detailed below:

1) Power module: A pair of electromechanically interlocked

contactors (for mains & generator) Overload relay for

generator contactor Neutral contactor for mains and

generator Power socket for connections.

2) Control and metering module: Line voltage monitor.

Generator voltage monitor Ammeter 3 items attempt start

facility. Air circuit breakers/MCB/MCCB of suitable rating for Rupees Four

auto/manual operation. Auto/manual switch. Emergency Lakhs Forty

stop push buttons. Manual start push button. frequency Three Thousand

276 meter. Engine hour meter. Two earthing studs. 3) Protection Each 1.00 443320.31 Three Hundred

module: The engine shutdown in the unlikely event of Low Twenty and

lube oil pressure High cylinder head temperature. V belt Paise Thirty One

4) Indicators with alarm Load on generator.

5) Indicators Load on mains Engine fails to start . Emergency

stop battery charger.

The AMF Panel of following capacity (G) AMF Control Panel

for 500 KVA 3 phase DG Set

Providing, erecting, testing commissioning & getting Plan

Approval as well as NOC from Electrical Inspector for

extensible H.T panel comprising of one 400A. H.T. VCB

incoming & Two outgoing 400 A Drawout type VCB

confirming as per I.S. for use on 11 KV, 3 phase, 50 c/s.

unearthed A.C. supply system having breaking rupturing

capacity of 350 MVA complete with spring operated

mechanism, mechanically & automatic ON-OFF and spring

mechanism charged, discharged indicators, ON-OFF

mechanical push button, operation counter necessary

auxiliary switches, closing shunt trip, air insulated busbar

chamber having heat shrinkable PVC sleeves, mechanical

interlocks safety shutters, isolating plugs and a VCB trolley

with three vacuum interrupters with epoxy support

insulators and self aligning finger type isolating contacts.

The breaker shall be Manual cum motorised mechanism &

auto spring charge with TNC switch closing with following

1. flush mounting type digital multifunctional meter with

communication facility - Three sets.

2. Power Factor Meter One No

3. Double core current transformer cast resin type having

ratio 200 to 50/1 core for metering & second core for

protection having required class of accuracy. - Three Sets

Instantaneous under voltage relay& Temperature rise

5. Electrical closing coil & short trip coil operating on 110V.

D.C.- Three Sets

6. Auxiliary relay for anti pumping device

7. Three phase Three limb Drawout type feeder connected

& output of 200 VA cast resin insulated potential

transformer having ratio 12000V./110V. and 200 VA Burdon

with 0.5 accuracy. - One No. Rupees Thirteen

8. Common Alarm bell operating on 110V A.C.- One No. 9. Lakhs Twenty

Digital KWH Meter - One No. Eight Thousand

277 10. Cable boxes suitable up to 11 KV 3core 150 sq.mm XLPE Ea 1.00 1328836.80 Eight Hundred

cable. - Three Nos. 11. 230V. A.C. to 110V. D.C. power pack Thirty Six and

for closing & tripping circuit common. 12.Breaker ON-OFF, Paise Eighty

Auto trip and spring charged indicators. - Three Sets. Only

13.Phase indicating & panel illumination lamps with plug

socket - Three Sets. 14.Numerical Communicable type non

directional O/C & E/F Relay with a setting of 5-250% both in

O/C & E/F. -Three Set complete with necessary

interconnection with air insulated high grade copper busbar

{Breaker Testing scope include Closing Time, Opening Time,

VCB Hi-Pot test at Site}{ Relay Testing Scope Include testing

of all protection by three phase testing kit at site }(VCB

Trolley is to be provided)

Providing and erecting sandwitched type bus duct having

following specification : Sandwich type busbar for use as

Feeder Busbar for interconnection between separate

electrical equipment/ load centers, and for use as Plug in

busbar risers.The busbar shall be suitable for operation in a

690V / 1000 V system with frequency of 50 Hz .System can

be either earthed or unearthed. Impulse voltage should be

12 KV. Standards: The busbar shall be designed and

manufactured in accordance with the following

international standards for busbar trunking.

-IS 8623/ 1993 Part I & II : Particular requirements of busbar

trunking System

-IEC 61439 Part I & VI : Particular requirements of busbar

trunking System

-IEC- 60529 : Degree of protection TESTING

The busbars shall be type tested at a reputable national /

International test laboratory (ASTA or CPRI) for short circuit

withstand. The test shall be for a minimum duration of one

Providing, erecting, testing & commissioning approved

make oil immersed ONAN cooled, double wound, core type

indoor / outdoor copper wound 11KV/ 433V step down

transformer of following capacities operating on 3 phase,

Hz 4 wire & neutral earthed system continuously rated for a

full temperature rise in oil not exceeding 45 Deg.C.at

maximum ambient temp. of 50 Deg. C. complete with

necessary radiator first filling of new transformer oil &

standard fitting as below complying with IS 1180( Part

):2014 standards with energy efficiency level 2 Off load tap

changing range manufacturers steps +2.5% to -5% on H.V

for variation should be provided. The H.V. shall be

connected Delta & Secondary with star connection. The

transformer should have cable-end boxes on H.T. side

suitable for up to 3 core 150 sq.mm. XLPE cable & on L.T.

side suitable for bus duct or cables as per requirement

complete with test certificates from

1. Oil conservator with filling Hole & Cap - One No.

2. Thermometer pocket with 6" dial type thermometer

switch alarm & trip contacts- Two nos.

3. Silica-gel breather with charge- One No.

4. Plain oil level gauge - One No. 5. Drain / Sampling /

Filter valve- One No.

5. Drain / Sampling / Filter valve- One No.

6. Top Filter Valve - One No.

7. Explosion vent with Diaphragm - One No.

8. Rating & Diagram plate - One No.

9. Additional neutral bushing for earthing - One No.

Lakhs Fifty Six

Providing and erecting sandwitched type bus duct having

following specification : Sandwich type busbar for use as

Feeder Busbar for interconnection between separate

electrical equipment/ load centers, and for use as Plug in

The busbar shall be suitable for operation in a 690V /

V system with frequency of 50 Hz .System can be either

earthed or unearthed. Impulse voltage should be 12 KV.

Standards: The busbar shall be designed and manufactured

in accordance with the following international standards for

busbar trunking.

-IS 8623/ 1993 Part I & II : Particular requirements of busbar

trunking System

-IEC 61439 Part I & VI : Particular requirements of busbar

trunking System

-IEC- 60529 : Degree of protection TESTING

The busbars shall be type tested at a reputable national / Rupees Nine

International test laboratory (ASTA or CPRI) for short circuit Lakhs Fifty Six

withstand. The test shall be for a minimum duration of one Thousand Five

second. Hundred Sixty

• Degree of ingress protection (IP rating) shall also be tested and Paise

at any reputed independent laboratory. This test shall be for Ninety Only

IP 55 for Indoor and IP 65 for Outdoor application.

• Short circuit and Degree of protection type test reports

will be submitted for vThe bsubars shall be of high

conductivity Copper of 99.9% pure ETP grade and high

conductivity Aluminium of 99.59% pure 19501 grade. Where

as earth conductor is required, it shall be separate external

It should be possible to provide a 200% Neutral where

Phase cross over box should have busbars crossing over

each other not cables.The busbars shall be individually

insulated with 2 layers of insulating film. Layers of

POLYSTER material class ‘F’, 155ºC.

The housing shall be made of 1.6 mm electrogalvanised

sheet steel, with an epoxy powder coated paint finish of RAL

7032 grade. Alternatively Aluminum casing of 2.5mm may

also be provided. The housings shall be profiled, to provide

higher strength and efficient heat dissipation. The width of

the housings shall be same for all ratings of busbars, in

order to provide interchangeability of tap off boxes.

The joints between sections shall be made so as to provide

flexibility during installation and expansion / contraction of

busbar during operation. The joints shall be of the single

bolt type. The joint construction must have the following

a) Thermal expansion of Busbars at joint of at least 4 mm

b) The joint insulation must be of one piece moulded design

and not have any cut edges which can absorb moisture.

c) Joint assembly shall be removable as separate sub-

assembly so that it can be inserted or removed without

disturbing the adjacent sections.

d) The joint system must be designed in a way that the

installer cannot insert the busduct length too far and

damage the bolt insulator.

e) The busbars ends shall not have any holes or slots at the

joints – the electrical continuity shall be through pressure

plates, achieving a high area of joint cross section and

expansion capability.

a) Plug in boxes will be draw out type, contacts shall be

silver plated and spring loaded.

b) The front operating handle will be interlocked with the

plug-in boxes cover so that MCCB can be operated only with

suitable cover in close position.

c) The door shall be provided with the door knobs.

d) When the MCCB is in ‘ON’’ position, even with the door

knobs unlocked, the operator should not be able to remove

the box or open the tap off location cover.

e) During insertion, the earth conductor shall make contact

first before the phase conductors. This should follow the Rupees Thirteen

sequence of first in last out concept. Thousand Nine

279 f) When the box is open the live conductors shall be safe Mtr 10.00 13995.57 Hundred Ninety

guarded by a transparent insulator plate which allows for Five and Paise

visible inspection but does not allow touching of the live Fifty Seven Only

conductors. g) The tap off unit arrangement must achieve IP

54 without requiring any additional sealing at site.

h) The tap off boxes will be suitable for accommodating

MCCBs or other accessories, as required. The tap off units

should allow the flexibility of accommodating different,

reputed MCCB makes, to be mutually agreed depending on

the tender requirements. (e)1250 Amp. capacity

Providing and erecting ISI Marked 3core 120 Sq.mm XLPE Rupees One

insulated 11 KV armoured cable Aluminium conductor IS- Thousand Five

7098 to be laid on wall with clamps or in provided cable Hundred Forty

trench / pipe approved manner as directed. Two and Paise

Providing and erecting cable end termination kit, heat

shrinkable Push on type Densons/ Raychem/ Elastimold

make suitable for 11 KV XLPE cable 3core 95 & 120 Sq.mm

281 (A) Outdoor type Ea 2.00 14611.67

and Paise Sixty

Providing and erecting cable end termination kit, heat Rupees Eight

shrinkable Push on type Densons/ Raychem/ Elastimold Thousand Four

282 make suitable for 11 KV XLPE cable 3core 95 & 120 Sq.mm Ea 5.00 8004.25 and Paise

(B) Indoor type Twenty Five

Design, Supplying, installing, testing of factory fabricated

ready made Three phase APFC Panel Cubical Panel

fabrication should be type tested as per IEC

61439:1&2 Capacitor Duty Contactor for switching as per

following Steps Incomer Switch of MCCB type Icu=Ics=50KA

at 400/440 Volts, with OC, SC, internal earth fault

protection Incomer Switch of MCCB type Icu=Ics=50KA at

400/440 Volts, with OC, SC, internal earth fault Rupees Five

protection,Copper tinned insulated Busbar,Cubical panel Lakhs Eighty

should be indoor type with IP 43 and IK 10,Metalized Thousand Three

polypropylene film tye3-phase 550Volt Capacitor,De tuning Hundred

Reactor for each capacitor,Panel having Short Circuit and Twenty Three

Overload protection,Each step Capacitor having suitable and Paise

MCB with Sc, OL, internal earth fault relay,Each stage having Seventy Eight

Stage Contactor (Capacitor load rating),PF regulator master Only

controller having suitable steps with LCD display, Rs

Communication port, Indication LED Lamps for main

incomer and ON-OFF for each capacitor bank,MS Chanel for

Floor mounting, Cable entry as per site situation,Cooling

fans for panel (f)200KVAR

Providing, and erecting 11 KV D.P. 9 mtr. high Structure

made of 6" x 3" ‘I’-Section Girder, 4" x 2"channels, clamps,

nuts, bolts etc. Suitable for erection of the followings duly

connected with necessary ACSR conductors. as per drawing

approved by the Engineer- in charge complete with

following. Height as per IS 7 Mtr above ground ) (A) 11 KV

200 Amps Drop out fuses with S.R.B.P. tubes carries.-Three

nos (B) 11 KV G.O.D. switch complete with insulators,

284 operating handle with galvanised pipe, Sq.bar etc. 400 Ea 1.00 98433.59

Amp.- One Set (C) 11 KV lightening arrestor with clamp-

and Paise Fifty

Three Nos. (D) 11 KV shackle insulators- Six Nos. (E) The

above D.P. structure should be earthed with 25 mm.X 3 mm

thick double copper earth strips run separately and

connected with separate copper plate earth electrode.

Providing and erecting required size Copper strip for

earthing of H.T. OCB / ACB/ Transformer, LT panel board,

Motors etc. using copper clamp.

285 Kg 100.00 794.87 Four and Paise

Providing and erecting HOT deep Galvanised iron strip wire

Seven and Paise

Providing and erecting required size HOT deep Galvanised

iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT

Seven and Paise

287 panel board, Motors etc. using proper clamp. Kg 80.00 77.77

Supplying & erecting earth pit of minimum bore dia.150mm

size approved make Earthing Electrode consisting Pipe-in-

Pipe Technology as per IS 3043-1987 made of corrosion free

hot dipped G.I.Pipes having Outer pipe dia of 50mm having

80-200 Micron galvanising, Inner pipe dia of 25 mm having

200-250 Micron galvanising, connection terminal dia of

12mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable

for following type of applications with chamber and heavy

duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of installation

duly stamped and signed by agency and officer Incharge has

to ensure the value of earthing resistane mentioned in test

288 Nos. 20.00 5760.03 Hundred Sixty

Certificate) & having back filling compound of (B) Inner

and Paise Three

chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter

testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no

load & dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable to

retain moisture for long time Necessary test report must be

submitted by Agency. (b)For Electrical installation up to

KV in normal soil.

Length of Pipe : 2.00 mtrs

Back filling Compound :1 no. Bag of 25 Kg.

(c) For Electrical Installation covering Transformer Neutrals,

Lightning arrester Earthing, A.C.Plant & Sensitive Computer

System(like Automation, SCADA) i.e independent Earthing in

289 Ea 6.00 8636.51 Hundred Thirty

Length of Pipe : 3.00 mtrs

Back filling Compound :2 nos Bags of 25 Kg.

Supplying & erecting D.C.P. type fire extinguisher for

following capacity cartridge type with gun metal cap 150 Rupees One

gram CO2 gas cartridge, powder and brackets confirming to Thousand Seven

290 IS 2171 1985 and complete erected with necessary clamps Ea 10.00 1712.96 Hundred Twelve

made from 50 x 6 mm M S Flat with nuts and bolts grouted and Paise

in wall complete.[A] For 5 Kg Capacity Ninety Six Only

Supplying & erecting D.C.P. type fire extinguisher for

following capacity cartridge type with gun metal cap 150 Rupees Two

gram CO2 gas cartridge, powder and brackets confirming to Thousand Two

291 IS 2171 1985 and complete erected with necessary clamps Ea 10.00 2226.04 Hundred

made from 50 x 6 mm M S Flat with nuts and bolts grouted Twenty Six and

in wall complete.[B] For 10 Kg Capacity Paise Four Only

Providing and fixing printed instruction chart both in English Rupees One

and Gujarati and duly framed with front glasses, for Hundred Thirty

292 treatment of person suffering from Electric shock with Ea 2.00 130.29 and Paise

minimum 50" diagonally size. Twenty Nine

Providing pair of rubber hand gloves suitable for working on Rupees Two

11 KV/22 KV supply. Hundred

293 Ea 2.00 214.12 Fourteen and

Supplying rubber matting of following thickness as per

IS:15652/IEC 61111 (b)4mm

294 Sq. Mtr 12.00 1027.17 Twenty Seven

Supplying rubber matting of following thickness as per

IS:15652/IEC 61111 (c)12mm

295 Sq. Mtr 6.00 3081.51 Eighty One and

Paise Fifty One

Supplying stand first AID box with antiseptic cream,

medicine for use on wounds due burn, crepe bandage,

gauge bandage, medicated ready to use bandage (Band-aid)

296 Ea 2.00 299.97 Nine and Paise

adhesive tape for medicinal user, Scissors, anti-septic

solution (Savlon or similar) etc. (All above contents shall be

of standard makes)

Supplying FIRE bucket round bottom of 9 litres capacity

made out of 24 gauge G.I. sheet with extra handle at

bottom duly painted white inside and Red out side with

297 Ea 6.00 214.12 Fourteen and

FIRE mark, filled with dry-sand and kept on existing stand

provided or hung on wall hook.

Supplying and erecting floor mounting stand for keeping

four nos. of FIRE buckets comprising 1500 mm in length, 900 Rupees Nine

mm height frame made out of 30mm X30 mm X 4 mm Hundred Forty

298 angle iron with cross supports for legs, welded with 4 hooks Ea 6.00 942.33 Two and Paise

and duly painted with one coat of red lead and two coats of Thirty Three

approved enamelled silver paint. Only

Wall hook 22 to 25 cms. projection for keeping fire buckets Rupees Sixty

299 made out of 15 mm dia. M.S rod grouted in wall to a depth Ea 6.00 60.60 and Paise Sixty

of minimum 15 cms. Only

Transformer oil having good resistance to high electrical

stress, high di-electric strength (50KV) low viscosity, low Rupees Ninety

300 pour point, high flash point and excellent thermal properties Ltr 20.00 90.90 and Paise