Cleaning of Septic Tank, MH, SWT, Sewage Line, Repairs Replacement to Sewage Line, Manholes, Area Drainage, Cover Slab and Repairs to Hardstanding and Culvert and Repairs to Stone Pitching, Retaining Wall, Compound Wall, Chain Link, Concertina Coil,

Amount

M & L for cleaning of Septic Tanks / Soak Wells / Man Holes etc. not exceeding 1.50m depth by pumping out the sewage water completely removing the Sludge, Silt, Debris etc. and other materials by suitable means, preferable mechanical means and Cleaning the internal surfaces with fresh water and applying Bleaching Powder @200 Grams per Sq.m and removing all the materials obtained to outside MD Land exceeding 5.00 KM distance and cleaning the complete area including making good any damages to the Septic Tanks / Soak Wells / Man Holes etc. complete all as required and as directed. Note: Quantity shall be measured from top of Sludge / Sewage Water Level to Bottom of Tank / Pit. The Foul / Waste Material and Sludge shall be disposed to out side MD land exceeding 5.00 KM distance. Nothing shall be paid extra for dewatering and cleaning with fresh water and applying Bleaching Powder and rate quoted shall be deemed to be inclusive of the same. The cleaning shall be carried out in a Phased Manner Periodically as required and as directed by the Engineer-in-Charge. Bleaching Powder shall be measured and paid separately.

All as per Serial Item No. 1 above but Depth of Septic Tanks / Soak Wells / Man Holes etc. exceeding 1.50m and not exceeding 4.50m complete all as specified and directed.

Supply only Bleaching Powder [ISI Marked] complete all as specified and as directed.

M & L for Clearing the blockage in the Sewage Lines of 100mm dia completely by rodding with Split Bamboo / Cleaning Rods preferably by Mechanical means so as to clean the Blockage and to enable the Sewage / Effluent to flow freely to the next Manhole, removal of sludge and other materials obtained from the Sewage Line to outside MD Land exceeding 5.00 KM distance, flushing the Sewage Line with Water including pumping of Sewage Water and cleaning the complete area including making good any damages to the sewage line or manholes complete all as required and as directed.

M & L for Clearing the blockage in the Sewage Lines of 150mm dia completely by rodding with Split Bamboo / Cleaning Rods preferably by Mechanical means so as to clean the Blockage and to enable the Sewage / Effluent to flow freely to the next Manhole, removal of sludge and other materials obtained from the Sewage Line to outside MD Land exceeding 5.00 KM distance, flushing the Sewage Line with Water including pumping of Sewage Water and cleaning the complete area including making good any damages to the sewage line or manholes complete all as required and as directed.

M & L for Clearing the blockage in the Sewage Lines of 200mm dia completely by rodding with Split Bamboo / Cleaning Rods preferably by Mechanical means so as to clean the Blockage and to enable the Sewage / Effluent to flow freely to the next Manhole, removal of sludge and other materials obtained from the Sewage Line to outside MD Land exceeding 5.00 KM distance, flushing the Sewage Line with Water including pumping of Sewage Water and cleaning the complete area including making good any damages to the sewage line or manholes complete all as required and as directed.

M & L for Removing blockages from Water Closets [Blocked / Choked] completely including connecting Traps, Spouts and Sewer Lines of any bore up to First Manhole preferably by manually means and by carefully Roding soil pipe with Split Bamboos or Flexible GI Wire etc to enable the flush water to flow freely to the Manholes to the entire satisfaction of user concerned and complete all as required and as directed.

M & L for cleaning the blockage in Gully Trap / Floor Trap / Nahani Trap completely to enable the sewage to flow freely to the next manhole, removing the sludge and other materials from the Traps by suitable means and removing all the materials obtained from the Traps to outside MD Land exceeding 5.00 KM distance and cleaning the complete area including making good any damages to the Traps to the entire satisfaction of user concerned complete all as required and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plan area and depth not exceeding 1.5m and getting out in Soft / Loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plan area and depth exceeding 1.5m deep and not exceeding 3.0m deep and getting out in Soft / Loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.

Removal of excavated material [Soil] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Demolition and Breaking up Drain Pipes, Salt Glazed / AC / PVC etc. of 100mm bore, Set in Cement Mortar including Concrete Bed and Haunching complete all as specified and directed.

Demolition and Breaking up Drain Pipes, Salt Glazed / AC / PVC etc. of 150mm bore, Set in Cement Mortar including Concrete Bed and Haunching complete all as specified and directed.

Demolition and Breaking up Drain Pipes, Salt Glazed / AC / PVC etc. of 200mm bore, Set in Cement Mortar including Concrete Bed and Haunching complete all as specified and directed.

M & L for concrete bed to drain pipes of size 100 mm bore packing under and haunching against the sides of pipes after they are laid and fitted in cement concrete, Type C2, 1:3:6, using 40mm graded stone aggregate complete all as specified and as directed.

M & L for concrete bed to drain pipes of size 150 mm bore packing under and haunching against the sides of pipes after they are laid and fitted in cement concrete, Type C2, 1:3:6, using 40mm graded stone aggregate complete all as specified and as directed.

M & L for concrete bed to drain pipes of size 200 mm bore packing under and haunching against the sides of pipes after they are laid and fitted in cement concrete, Type C2, 1:3:6, using 40mm graded stone aggregate complete all as specified and as directed.

S & F 110mm bore HDPE DWC Pipes, Class SN8, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F 150mm bore HDPE DWC Pipes, Class SN8, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F 150mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F 200mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

Demolition of Cement Concrete of any description and in any position not otherwise specifically provided for and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

Demolition of Reinforced Cement Concrete [reinforcement cut as required to facilitate demolition] of any description and in any position not otherwise specifically provided for and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

Demolition of Brickwork or Stone / Boulder Masonry, built in Cement Mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces etc including raking out joints, hacking for key scrubbing down with water etc and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

Desilting of Drains [Covered or Open] in any condition [including foul condition] with necessary dewatering and temporary diversion of drain water as required including disposal of spoil to a distance exceeding 250m but not exceeding 500m including removing and replacing cover slabs complete all as directed.

M & L for PCC 1:3:6, Type C-2 [using 40 mm graded granite stone aggregate] in surface channels and drains including forming fair finished drain or channel of any inner girth using extra cement including forms, moulds, mitred / stooped ends complete all as specified and as directed.

M & L for Plain / Reinforced cement concrete Type B1 [Nominal Mix] 1:2:4 using 20mm graded stone aggregate Cast in Situ in Lintels up to 1.5m Span, Cills, Steps, Seismic and Other Similar Bands, Plinth Courses, String Courses, Lacing Courses, Parapets and Railings up to 60 cm in Height, Copings, Kneelers, Apex Stones, Bed Plates including Weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work, complete all as specified and as directed.

M & L for providing Precast RCC 1:2:4, Type B-1, using 20mm graded stone aggregate as in Landings, Cover Slabs [for Manholes etc], Chullah Hoods, Chajjas, Water Troughs, Mangers, Shelves and similar articles with plain faces set in Cement Mortar 1:6 complete all as specified and as directed.

M & L for brick work with Fly Ash bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

M & L for Providing Precast Cement Concrete Solid Block Masonry with Solid Blocks exceeding 100mm width of PCC 1:3:6, Type – C1 using 20mm graded stone aggregate set in Cement Mortar 1:6 complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4, surfaces finished even and smooth without using extra cement including mixing of water proofing compound of approved make as per manufacturers instructions complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

S & F Mild Steel work confirming to Fe - 290, Grade E-165, as in framed work such as Grills, Gratings, Ladders etc with ends of bars shouldered and/or riveted, or forged into spikes, framed Guard Bars, Barred Iron Doors, Ladders, framed Balusters, Walk Ways, Railings, framework of Water Tanks and similar work complete all as specified and as directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

S & F 75mm bore PVC [SWR] pipes single socketed, in any length as in Spouts or Weep Holes in Masonry / Concrete Walls complete all as specified and as directed.

Dismantling Stone Pitching in Portions built in Cement Mortar including levelling the dismantled area to get the even surface by removing the vegetation etc. complete all as specified and as directed.

M & L for Boulder Pitching, hand packed tightly, grouted with Cement Mortar 1:6 complete all as specified and directed.

All as per Serial Item No. 41 above but except Boulders complete all as specified and directed.

M & L for 100 mm thick, PCC 1:4:8, Type D-2, using 40mm graded aggregate as in Sub base for flooring complete all as specified and as directed.

M & L for 100 mm thick, PCC 1:2:4, Type B-1 using 20mm graded aggregate as in Floors / Hard standing etc, surface finished even and smooth with out using extra cement and spike rolling to surfaces or making impressions of expanded metal, while the concrete is green complete all as specified and as directed.

M & L for 50 mm thick, PCC 1:2:4, Type B-1 using 20mm graded aggregate as in Floors / Hard standing etc, surface finished even and smooth with out using extra cement and spike rolling to surfaces or making impressions of expanded metal, while the concrete is green complete all as specified and as directed.

M & L for Inter Locking Paver Blocks of 60mm thick, made with M35 Grade Pre-Cast Cement Concrete using 20 mm graded stone aggregate, PVC Mould reflective type, Hydraulically Pressed of approved shape, size, pattern and colour conforming to IS - 15658 including 50mm thick Sand Cushion / Bed to Inter Locking Paving Blocks including filling interstices complete all as specified and as directed.

M & L for Glazed Polish finished coloured Designer Chequered Cement Concrete Tiles of thickness 23 to 25mm, made with M-25 Grade Precast Cement Concrete, Hydraulically pressed of size not less than 300 X 300 mm, of approved Shape, Colour, Design and Pattern, set, jointed and pointed in neat cement slurry to match including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed.

M & L for brushing neat Cement Slurry with 3.0 KG of cement per Sq.m area complete all as specified and as directed.

M & L for Forming Fair Finished Drain or Channel 30cm Inner Girth in Cement Concrete, using extra cement, including Forms, Moulds, Mitred / Stopped ends etc. complete all as specified and as directed.

Supply only Integral Water Proofing Compound [ISI marked] of approved make complete all as specified and as directed.

Cutting chases, pinning in Brick Walls, making good to facings where required and pointing in Cement Mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting exceeding 20 cm girth brick walls complete all as specified and as directed.

M & L for 100 mm thick, PCC 1:2:4, Type B-1 using 20mm graded aggregate as in Floors / Hard standing etc, surface finished even and smooth with out using extra cement complete all as specified and as directed.

S & F in repairs PVC Nahani Trap 100mm dia with Grating including jointing to waste pipe fixed in Cement Concrete, Type B1, 1:2:4 complete all as specified and as directed.

S & F in repairs 100mm Diameter Stainless Steel Anti Cockroach Floor Trap with SS Grating including jointing to Nahani Trap, fixed in PCC 1:2:4, Type B0 using 10mm graded stone aggregate complete all as specified and as directed.

M & L for Loose Filling with broken Bricks of gauge 80 to 150mm in soakage pits etc. complete all as specified and directed.

Use and removal of Steel Formwork to Soffits of Suspended Slabs such as Roof Slabs, Floor Slabs, Landings and similar work not exceeding 200mm thick [Horizontal or Sloping] for Fair Finished surfaces complete all as specified and directed.

S & F in repairs 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F in repairs 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F in repairs 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps as in rain water down pipes complete all as specified and as directed.

S & F in repairs 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps as in rain water down pipes complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Bends of any radius with Access Door including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Bends of any radius with Access Door including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal without access door including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal without access door including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Junction Double [Double "T"] equal or unequal without access door including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Junction Double [Double "T"] equal or unequal without access door including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed.

S & F PVC [SWR] Gully Trap 125/110 mm, with grating including setting and jointing with solvent cement complete all as specified and as directed.

M & L for Cutting Bituminous Road / Hardstanding etc. as required for Jointing / Laying Cables and Pipeline of width not exceeding 1000mm and depth not exceeding 500mm and refilling after laying and making good with PCC 1:2:4, Type B1 using 20mm graded stone aggregate, 100mm thick over 100mm-300mm thick Hardcore of Guage 40mm-63mm size boulders over 100mm thick Sand filling complete all as specified and as directed.

Dismantling of Floor, Hearth or Wall Tiling of any description including Cement Mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris to a distance not exceeding 1.50 KM complete all as specified and as directed.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.06 Sq.m and not exceeding 0.11 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Joint Free Glazed Ceramic Tiles, Edge Cut, Concept Type, Coloured, Premium Quality, of size 450 mm X 300 mm, 7 to 8 mm thick as in Vertical Surfaces such as Skirting, Dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. The colour / shade / design of tiles shall be as approved by GE.

S & F in repairs Vitreous China Squatting Pan "Orissa Pattern" of size 580 mm X 440 mm, White with integral foot rests and 'P' or 'S' trap including provision of lime concrete bedding complete all as specified and as directed.

S & F in repairs Vitreous China Wash Down Water Closet [Pedestal pattern], White including Plastic Water Closet Seat back closed pattern with Flat Bottom and Cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' Trap complete all as specified and as directed.

S & F in repairs 10 Litres capacity, PVC Valve less, Syphonic action type, Low Level Flushing Cistern, White, with Inlet Ball Valve, Float, Handle, including Brackets and Connections to Pipe and Flush Pipe complete all as specified and as directed.

S & F in repairs Vitreous China Ware Wash Hand Basin, White, Flat Back of size 550 mm X 400 mm including Brass Chromium plated Waste Fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe, PVC Connection of 15mm Bore and 600mm long with PTMT check nut and union etc. complete all as specified.

S & F in repairs Waste Fittings, 40 mm dia, Brass, Chromium plated for stainless steel sink with drain board or without drain board, glazed ware sinks, Wash Basins etc. with long screwed shanks and fly-nuts, flange end bedded in red led cement and other end fixed complete all as specified and as directed.

S & F in repairs Angle Cock, 15 mm dia, cast copper alloy with capstan head, Chromium Plated, with Wall Flange screwed down high pressure with crutch or butterfly handle for iron pipe etc. complete all as per Jaquar Catalogue No. CON-059KN or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F in repairs Two way Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as per Jaquar Catalogue No. CON-041KN or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F in repairs 32mm dia PVC Flexible Waste Pipe, 750 mm long fixed to Wash Hand Basin or Sink in repairs complete all as specified and directed.

S & F in repairs 40mm dia PVC flexible Waste Pipe, 750 mm long fixed to Wash Hand Basin or Sink in repairs complete all as specified and directed.

S & F in repairs PVC Connection of 15mm Bore and 450mm long with PTMT check nut and union etc complete all as specified and as directed.

S & F 20mm outer dia of pipe, 3–layer PP–R Polypropylene random copolymer] concealed pipes of SDR 7.4 [PN–16] UV stabilised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings complete to walls, ceilings or in floors etc. including testing including taking down or up steel tubing and connections of any description complete all as specified and as directed.

S & F Mild Steel Bars, 10 mm dia and over cut to length, bent to shape required as in Rungs of Manholes embedded in Concrete and fixed with support complete all as specified and as directed.

M & L for Uprooting and Removal of Wild Trees / Grass / Bushes etc. from the Manholes / Soil Pipes / Septic Tanks / Soak Wells and their surroundings including its penetrated roots and making good the damaged plaster with Cement Mortar [1:3] and finished the surfaces to match with existing surfaces complete all as specified and as directed.

M & L for Making good Masonry Walls / RCC Walls damaged during replacement of Pipe lines etc. on vertical wall surfaces at any height with Cement Mortar [1:3] or PCC 1:2:4, Type B-0 using 10mm graded stone aggregate and finished the surfaces to match with existing surfaces including painting as per existing treatment complete all as specified and as directed.

M & L for walling of random rubble masonry, uncoursed, well bonded, bedded and solidly hearted, built in Cement Mortar 1:6 complete all as specified and directed.

All as per Serial Item No. 88 above but except Stone complete all as specified and directed.

M & L for Forming Base Surface suitable for providing Stone Pitching using approved earth / Moorum obtained from outside MD Land for filling undulations and bringing up to slopes / surface including raising [or lowering] earth, spreading in layers not exceeding 15cm thick, watering, ramming / consolidation complete all as specified and as directed.

M & L for removing Vegetation / Small Plants / Shrubs from the external surfaces of the Stone Pitching including uprooting complete and taking down damaged / broken / cracked / loose Cement Mortar Grouting from existing Stone Pitching, cleaning the interstices and making good the disturbed surfaces by grouting with Cement Mortar 1:4 complete all as specified and directed.

Raking out Joints / Pointing to Random Rubble or Polygonal Rubble uncoursed or brought up to courses or Stone / Boulder Pitching etc. grouted /pointed in Cement Mortar complete all as specified and directed.

M & L for Flush Pointing in Cement Mortar 1:4 to Random Rubble uncoursed or brought up to coursed Masonry / Stone / Boulder Pitching complete all as specified and directed.

M & L for PCC 1:4:8, Type D–2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4, surfaces finished fair and even complete all as specified and as directed.

M & L for preparation of newly plastered Wall Surfaces and applying Two Coats of Cement Based Paint over One Coat of Alkali Resistant Primer complete all as specified and as directed.

M & L for RCC 1:1½:3, Type A-1, using 20mm graded stone aggregate as in Foundations including Rafts, Footings, Foundation Beams, Plinth Beams, Bases for Columns etc complete all as specified and as directed.

M & L for RCC 1:1½:3, Type A-1, using 20mm graded stone aggregate as in Columns, Pillars, Piers, Posts and Struts etc. complete all as specified and as directed.

Use and removal of Steel Formwork to Sides of concrete Foundations, Pile Caps, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits [if any] of Foundation and Plinth Beams and similar work, Vertical or to Batter for Rough Finished surfaces complete all as specified and as directed.

Use and removal of Steel Formwork to Sides of Pillars, Posts, Struts, Piers, Columns and Stanchions of any Shape / Cross Section for Fair Finished surfaces of concrete complete all as specified and as directed.

Dismantling Fencing Wire Mesh including Concertina Coil & Barbed Wire of any type including Running Bars, Straining Wires etc. complete all as specified and as directed.

Dismantling of Wrought or Mild Steel Work of any description not otherwise specifically provided for complete all as specified and as directed.

Excavation in Post holes or similar holes each not exceeding 0.5 Cu.m, getting out in Soft / Loose soil, including returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm thick, watering and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and as directed.

S & F Mild Steel work confirming to Fe - 290, Grade E-165 as in Hand Rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for Balusters Running Bars, for Doors, Balusters, Nosing to Steps including embeding in concrete and screwing etc, Wind Ties for roof including securing bolts, Posts and Struts in Fencing including cutting tops to shape as directed, bending to shape, notching for wire, drilling holes or as in flat iron fillets [for securing wire mesh and barbed wire etc] including all necessary drilling, bolting or riveting, etc and similar work complete all as specified and directed.

S & F MS Machine made Screw Bolts [Galvanised] with hexagonal or square head one end and screwed other or screwed both ends, fitted with washers and one hexagonal or square nut exceeding 5 cm and nor exceeding 10 cm long, dia of neck exceeding 16 mm but not exceeding 20 mm complete all as specified and as directed.

S & F MS Round bars 10mm dia and over, cut to length, bent to shape and binding with MS wire as in Running Bars for Chain Link / Barber Wire Fencing complete all as specified and as directed.

S & F Concertina Coil Fencing with Punched Tape Concertina Coil made from High Tensile Spring Steel, High Carbon Wire conforming to IS – 4454 [Part – 1], of Grade – SM duly Hot Dipped Galvanised as per IS – 4826 with 230GSM, 600mm dia, 10 Metre openable length, with Galvanised coating and Punched Tape material as per IS – 513, having 50 Nos Rounds per 6 Metre length [before stretching], having medium barbs [Barb Length 24±1mm, Barb Width 19±1mm, Pitch between Two Barbs 35±1mm], Spring Core Wire [2.6 mm thick] of high tensile strength of 165 Kg / Sq.mm with tape [0.52mm thick] and weight 43.478 Grams / Metre and fixing to “Y” or Trapezoidal shaped angle iron brackets placed at 2.00m to 3.00m apart and with 6/9 horizontal RBT [Reinforced Barbed Tape] Wire, Stud tied with GI Staples and GI Clips to retain horizontal, including necessary bolts and coating with Px Compound [Anti Rust] complete all as specified and as directed. Note: Horizontal barbed wire & angle iron supports shall be measured and paid separately under relevant items of Schedule "A". Measurement shall be made for stretched length.

S & F Galvanised, 2 Strand, Steel Barbed Wire 2.24mm dia, Barbed with 2mm dia bars at 75mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc complete all as specified and directed. Note: Each line of wire will be measured for payment.

S & F PVC Coated Chain Link MS Galvanised Fencing Mesh of size 50 mm X 50mm, 4mm dia wire with Zinc coating of 275mm GSM and with minimum 1.5 mm thick PVC Coating [Total thickness of final PVC Coated wire is 5.50mm dia] and of weight not less than 4.0 KG / Sq.m including line wires, any mesh, size and type to any type of standards, rails, straining bolts, MS Flat Iron etc. including provision of binding wire complete all as specified and as directed. Note: MS Bar, MS Flat & MS Bolts are measured and paid separately under respective items of this BoQ.

M & L for preparation of old painted steel surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for washing, rubbing down and stopping of painted surfaces including removing Nails etc., filling Holes and Cracks with Plaster of Paris or Cement based Wall Care Putty, rubbing smooth and applying One Coat of Cement based Paint on Walls complete all as specified and as directed.

M & L for Running Welding in repairs including preparation of surfaces to be welded and thickness of metal welded exceeding 6mm and not exceeding 9mm complete all as specified and as directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces of any description, not exceeding 10 cm width or girth including preparation of surfaces complete all as specified and as directed.

SSV CONSTRUCTIONS (BID ID -3399678)

SRI RAJA RAJESWARI ENTERPRISES (BID ID -3400599)

SRI VENKATA SAI MANIKANTA CONSTRUCTIONS (BID ID -3400419)

Bidder Name

SRI VENKATA SAI MANIKANTA CONSTRUCTIONS

SWATHI CONSTRUCTIONS

SSV CONSTRUCTIONS

SRI RAJA RAJESWARI ENTERPRISES