PROVN OF SWT FOR HELIPAD AND PROVN OF TRADESMEN SHOP FOR TRADES OF MES AT ICGS VADINAR UNDER GE (I) CG PORBANDAR

Amount

SCHEDULE 'A'

M&L Moorum/ red bajari filling for area development laid in layers not exceeding 25 cm thick, spread levelled and consolidated by rolling using roller as specified, including watering, complete all as specified and as directed by Engr-in-Charge. Note: Only rolled thickness shall be measured and paid

Surface excavation n.exc 30 cm deep averaging 15 cm deep and getting out in soft/disintegrated rocks complete all as specified and as directed by engineer-in-charge. .

Excavating over areas n.exc.1.5m deep and getting out in soft/disintegrated rocks complete all as specified and as directed by engineer-in-charge. .

-Ditto- but exc.1.5m deep and n.exc.3m deep

-Ditto- but exc.3.0m deep and n.exc.4.5m deep

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in soft/disintigrated rocks complete all as specified and as directed by engineer-in-charge.

M & L Hardcore of gauge not exceeding 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed by engineer-in-charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils complete all as specified and as directed by engineer-in-charge.

Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and as directed by engineer-in-charge.

M & L PCC type D2 (1:4:8, using 40mm graded stone aggregate) in fdn filling and mass concrete complete all as specified and as directed by engineer-in-charge.

M&L RCC Design Mix, M-30 as in foundations, including rafts, footings, foundation beams; plinth beams; base for columns, etc.; basement slabs, unde-reamed piles and mass concrete complete all as specified and as directed by engineer-in-charge.

M&L RCC Design Mix, M-30 as in walls, retaining walls, basement walls, ballast wall and the like, any thickness, above top of footings incl attached pilasters & buttresses complete all as specified and as directed by engineer-in-charge.

M&L RCC Design Mix, M-30 as in dome slab and the like complete all as specified and as directed by engineer-in-charge.

M&L RCC Design Mix, M-30 as in coloums, pillars, piers, posts and struts complete all as specified and as directed by engineer-in-charge.

M&L RCC Design Mix, M-30 as in beams, lintel band and gable beams complete all as specified and as directed by engineer-in-charge. .

M&L RCC Design Mix, M-30 as in chajjas complete all as specified and as directed by engineer-in-charge. .

M&L RCC Design Mix, M-30 as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies ,canopies, deck slabs and in shelve and like complete all as specified and as directed by engineer-in-charge.

M&L PCC 1:3:6 type B1 with using 20mm graded stone aggregate such as coping, bed plates, kerbs, water troughs and the like incl weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed by engineer-in-charge.

Supply only integral waterproofing compound only complete all as specified and as directed by engineer-in-charge. .

M&L Pre-cast cement concrete block masonary in PCC 1:3:6 type C1 using 20mm graded stone aggregate with solid block, exceeding 10 cm in width and setting in CM 1:6 complete all as specified and as directed by engineer-in-charge.

M&L Water proofing treatement by applying one coat of oil based bituminous primer @ 0.3 kg/sqm with brush /roller, laying of 3mm thick APP based polymer modified membrane (mineral finish) reinforced non-woven polyster, weight not less than 3.50 kg/sqm and sealing all the over laps 100mm in length side and 100mm in width side of membranes laid with torch application complete all as specified and as directed by engineer-in-charge.

M&L 40 mm thick Damp proof course in cement concrete 1:2:4 type B-0, including necessary form work with WPC as per manufacturer instruction by weight of cement. complete all as specified and as directed by engineer-in-charge.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work incl attached pillaster, buttresses, etc., vertical or to batter rough finished flat surfaces of concrete.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) on curved surfaces complete all as specified and as directed by engineer-in-charge.

Formwork to sides of column footing/plinth beam etc, rough finished surfaces of concrete flat complete all as specified and as directed by engineer-in-charge.

Formwork to sides of columns, fair finished surfaces of concrete square or rectangular complete all as specified and as directed by engineer-in-charge.

Formwork to sides of beam/lintel bend and similar structure for flat fair finished surfaces complete all as specified and as directed by engineer-in-charge.

Formwork to chajjas including edges for flat fair finished surfaces complete all as specified and as directed by engineer-in-charge. .

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; fair finished not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed by engineer-in-charge.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping, etc fair finished complete all as specified and as directed by engineer-in-charge.

S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed by engineer-in-charge.

S&F Solid PVC door frame of size 50 mm x 47mm made out of 5 mm thick plain coloured PVC sheet reinforced with MS square tube complete all as specified and as directed by engineer-in-charge.

S&F 30mm thick Factory made solid pannel PVC door shutter (Style) consisting of frame made out of MS tube for top/bottom rails, MS tube frame shall be covered with heat moulded plain coloured PVC 'C' channel having PVC sheet strip of 20mm width complete all as specified and as directed by engineer-in-charge.

S & F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed by engineer-in-charge.

S&F 100 mm long Butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and as directed by engineer-in-charge.

S&F 150 mm long Aluminium anodised barrel tower bolt complete all as specified and as directed by engineer-in-charge.

S&F 150 mm long aluminium alloy handle anodised fabricated type complete all as specified and as directed by engineer-in-charge.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed by engineer-in-charge.

M&L TMT CRS steel bars 10 mm dia and above, as in reinforcement for concrete, cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm complete all as specified and as directed by engineer-in-charge. .

All as per item No 39.00 above but above 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders.

S&F Aluminium Deco Grill (powder coated) of type DG 104, with necessary channels and clips.

S&F Fabricated Aluminium anodised (powder coated) doors, windows, partitions and ventilators using aluminium sections of size and type approved by Engr-in-Charge, including jointing cleats, snap beading & handles etc. complete all as specified and as directed.

S&F Rubber gasket of size 50mm X 6mm aluminium door, window and partition wall for fixing glass panes or prelaminated particle board etc. complete all as specified and as directed by Engr-in-Charge.

S&F Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and as directed by Engr-in-Charge

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples, complete all as specified and as directed by Engr-in-Charge

S&F UPVC, double flat / groove type,chrome finish roller for sliding windows all as directed by Engineer-in-charge.

S&F 100mm long powder coated Aluminium starlock for sliding window shutters conforming to the samples held in the office of Engineer-in-charge.

M&L Framed work such as such as door or gate of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other coverings, doors, etc., to be prepared for hanging or sliding complete all as specified and as directed

S&F Fabricate MS hold fast and similar small articles conforming to Fe-290 Gde E-165 complete all as specified and as directed by engineer-in-charge. .

M&L 75 mm thick, Cement concrete type D 2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring complete all as specified and as directed by engineer-in-charge.

M&L 25 mm thick, PCC 1:2:4 type B0 (using 12.50mm graded stone aggregate) as in sub base to receive tiles complete all as specified and as directed by engineer-in-charge. .

M&L Non-skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc set and pointed in neat cement slurry and pointed in white or coloured cement to match the surface over 15 mm thick screed bed in CM 1:6 complete all as specified and as directed by engineer-in-charge. .

M&L Glazed ceramic coloured tiles in vertical surface of size 450 x 300 x 7 mm set and jointed in neat cement slurry and pointed in coloured cement to match the surface over 10 mm thick rendering in CM 1:3 complete all as specified and as directed by engineer-in-charge.

M&L 75mm thick, PCC types C1 (1:3:6 , using 20mm graded stone aggregate) as in plinth protection, finishing cement concrete surface fair and even without using extra cement complete all as specified and as directed by engineer-in-charge.

M&L 40mm thick, PCC type B1 1:2:4, (using 20 mm graded stone aggregate) as in floor finish, cement concrete surfaces finished even and smooth complete all as specified and as directed by engineer-in-charge.

M&L Plain Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) as in benching of man holes including forming centre channels half round or 1/4 section complete all as specified and as directed by engineer-in-charge.

Extra for forming fair finished channel or drain 30cm girth (inner girth) in cement concrete using extra cement incl forms, moulds, mitred stopped ends.

M&L 5 mm thick, Rendering on ceiling on fair faces of concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and as directed by engineer-in-charge.

M&L 15mm thick, Rendering on other than fair face of Brick work/Concrete surfaces/Stone Masonry in CM 1:4 finished even and smooth without using extra cement including mixing water proofing compound @ 2% by weight of cement complete all as specified and as directed by engineer-in-charge. Note ;- WPC will be measured and paid seperatly.

M&L 15 mm thick, Rendering on fair faces of brick work/pcc block masonry or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and as directed by engineer-in-charge.

M&L Two coats of OBD on new plastered surface of wall over a coat of primer incl necessary preperation, complete all as specified and as directed by engineer-in-charge.

M&L Preparation of newly plasterd surfaces of walls over a coat of primer and applying two coats of cement based paint complete all as specified and as directed by Engr-in-Charge.

M & L Two coats of Acrylic emulsion paint over a coat of primer including preparation of new plastered surfaces of wall/ceiling complete all as specified and as directed by engineer-in-charge.

M&L Three coats of white wash on new plastered surfaces of ceiling including necessary preparation of surfaces complete complete all as specified and as directed by engineer-in-charge.

M&L Two coat synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description, over 10cm in width or girth, not otherwise described complete all as specified and as directed by engineer-in-charge.

M&L 20mm bore Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by engineer-in-charge.

M&L 15mm bore Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by engineer-in-charge.

S&F 500 Ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) triple layered hoisted and fixed in position all as specified in SSR Part I including provision of 100 mm long 50mm dia Nipples wiith check nut, for inlet, outlet, overflow and wash pipes complete all as specified and as directed by engineer-in-charge. Make:- Sintex or equivalent

S&F 20mm bore Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed in position complete all as specified and as directed by engineer-in-charge.

S&F 20mm dia ball valves high pressure of PTMT epoxy coated aluminium rod & high density plastic ball complete all as specified and as directed by engineer-in-charge.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls of bore 160mm (rates includes for making good disturbed surfaces) complete all as specified and as directed by engineer-in-charge.

S&F EWC double syphonic water closet pan of ivory colour (Cansino) with integrated flushing cistern complete including all fittings such as seat cover, flushing pipe, with flushing cistern (Make :- Cera Cat Pat No-S1012110-S-TRAP-110-W or equivalent) complete all as specified and directed by Engineer-in-charge.

S&F WHB of 500X420MM size and any colour of including cutting for and pinning in ends of brackets Make: CERA Cat Pat No-S2030121W or Equivalent complete all as specified and directed by Engr-in-Charge.

S&F 10 litre PVC valveless (ivory colour), syphonic action type flushing cystern low level with inlet valve, float and handle and PVC outlet suitable for IWC/EWC complete all as specified and as directed by engineer-in-charge. . Make:- Cera / Supermo or equivalent

M&L 15 mm dia bore Pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe. Make: CERA Cat Pat No-F1005101 or Equivalent complete all as specified and directed by Engr-in-Charge. Make:- Cera / Supermo or equivalent

S&F 15mm dia bore Fancy type bib taps, chromium plated cast copper alloy Make:- CERA Cat Pat No-F1005151 or Equivalent complete all as specified and directed by Engr-in-Charge.

S&F 15mm dia bore Fancy type angle cock, chromium plated cast copper alloy,screwed down,high pressure, screwed both ends for iron pipe or for unions and fixed Make:- CERA Cat Pat No-F1014201 or Equivalent complete all as specified and directed by Engr-in-Charge.

S&F PVC connection 15mm dia and 300mm long with synthetic metal nut complete all as specified and as directed by engineer-in-charge.

S&F Fancy type Soap dish, CP Brass Make: CERA Cat Pat No-F5003106 or Equivalent complete all as specified and directed by Engr-in-Charge.

S&F 100mm dia grating doom of PTMT (Minimum weight 25 gms) complete all as specified and as directed by engineer-in-charge.

S&F 100 mm dia bore CI soil, waste and vent pipe in any length in cement joint complete all as specified and as directed by engineer-in-charge.

S&F 75 mm dia bore CI soil, waste and vent pipe in any length in cement joint complete all as specified and as directed by engineer-in-charge.

S&F 75 mm dia bore CI cowl complete all as specified and as directed by engineer-in-charge.

S & F 100 mm outer dia cast iron floor trap out let including jointing to waste pipe fixed in cement concrete 1:2:4 complete all as specified and as directed by engineer-in-charge.

S&F 100 mm dia bore CI 'P' or 'S' trap complete all as specified and as directed by engineer-in-charge.

S&F 100 mm dia bore CI bend (any radius) diminishing pieces etc complete all as specified and as directed by engineer-in-charge.

S&F Fancy type Toilet paper holder,CP Brass Make: CERA Cat Pat No-F5002110 or Equivalent complete all as specified and directed by Engr-in-Charge.

S&F Fancy type Tubular towel rail, 20mm dia, brass CP, 60cm long between flanges Make:- Make:- CERA Cat Pat No-F5003102 or Equivalent complete all as specified and directed by Engr-in-Charge.

M&L for 150mm dia bore Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and directed by Engr-in-Charge.

M&L PCC 1:3:6 type C2 as in bed to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested.

M&L Soling (or sub base) with broken boulders or quarried stone, inter stices filled, spread thickness 150 mm, surface formed and rolled and consolidated to required gradient and camber complete all as specified and as directed by engineer-in-charge.

M&L Rolling and consolidating formation surfaces in cutting with power roller exc. 8 tonne and n.exc. 12 tonne complete all as specified and as directed by engineer-in-charge. .

M&L Applying evenly a tack coat with paving bitumen @10 Kg per 10 Sqm preparatory to bitumenous macadam complete all as specified and as directed by engineer-in-charge.

M&L 15cm thick (compacted thickness) WBM using granite traper basalt aggregate in two layers, with coarse aggregate of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size), spread, rolled and consolidated to gradient and camber required complete all as specified and as directed by engineer-in-charge. .

Preparing unsurfaced WBM by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc. complete all as specified and as directed by engineer-in-charge.

M&L laying and consolidating 50mm thick premixed bituminous macadam, with 4% binder content by weight of total mix, rolled and compacted to required camber and gradient (consolidated thickness 75mm or less) with 8 to 10 tonne power roller etc. using paving bitumen complete all as specified and as directed by engineer-in-charge.

M & L Preparing black top surfaces of road by brushing with wire brushes to remove caked mud etc. sweeping with brooms & finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc. and applying evenly a priming/tack coat with bituminous primer of paving bitumen at the rate of 5 Kg per 10 Sqm and laying bituminous premixed carpet 40mm consolidated thickness with 0.54 cubic metre stone chipping mixed with 29.2 KG of binder, rolled and compacted to required camber and gradient using 8 to 10 tonne power roller and applying premixed sand seal coat using 0.06 cum sand mixed with 6.80 KG of bitumen and rolling to a uniform smooth surface with 8 to 10 tonne power roller, complete all as specified and as directed by Engr-in-Charge.

Cutting into existing manholes for connecting new drains ,making good to pipe and rendering, cutting out existing benching for and forming branch channel(1/2 round or3/4 section)in cement concrete 1:2:4 type B-1 smooth finished ,and reforming benching as required, internal dia of pipe 150 MM complete all specified and directed.

M&L Point wiring complete with 1.5 sqmm single core PVC insulated but unsheathed copper conductor FRLS 1100 Volts grade cable, drawn through and including PVC concealed conduit heavy duty grade ISI marked 25 mm dia (external), ISI Marked, including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling etc including 1.5 sqmm PVC insulated but unsheathed copper conductor FRLS cable as earth continuity wire complete all as specified and directed by Engr-in-Charge for following:- Note: Cost of cutting / chasing on wall and making good after repair shall be measured and paid seperately. Make of cable: Havells/ Finolex/ RR Kable/ KEI

One light point /fan point controlled by one switch with cable 1.5 Sqmm

One 3 pin socket outlet 5 Amps on the same board with other switches with cable of size 1.5 Sqmm nominal area

One 3 pin socket outlet 5 Amps independent board with cable 1.5 Sqmm nominal area

One 3 pin socket outlet 15 Amps independent Board with cable of size 2.5 sqmm nominal area.

M&L Ceiling rose, surface type, 3 way terminal/PVC/Polycarbonate isolated body complete all as specified and directed by Engr-in-Charge.

S&F Switch piano, flush button,240V, 5 Amps, Single pole one way (ISI Marked) complete all as spd and directed by Engineer-in-Charge.

S&F Socket outlet, 3 pin 5 Amps, flush type (ISI Marked) complete all as spd and directed by Engineer-in-Charge.

S&F Switch Socket outlet multipurpose 6A, 6 pin, 240V type controlled by one piano switch complete all as specified and directed by Engr-in-Charge.

M&L Sub-main wiring alongwith earth wire with the sizes of 2 x4 Sqmm ,1x4 Sqmm earth wire of FR PVC insulated copper conductor, single core cable in PVC heavy duty concealed conduit of 25mm dia complete all as specified and directed.

S&F High efficiency aluminium linear LED Batten light 20 Watt with 6500 K with driver complete all as specified and directed. Make : Wipro Cat No. LL20-281-XXX-65AL1 or its equivalent in Philips/Crompton

S&F 5 star rated ceiling fan 1200mm sweep and connecting up to and including provision of 23/0.0076 (or equivalent size in mm) flexible three core PVC insulated copper conductor cable from ceiling rose to fan, hanging rod of suitable size, and electronic regulator etc complete.Make: Orient(Crown), CG(HS Plus), Havells (ES-50)/USHA (VETRA)

S&F Sheet metal enclosure for Single pole neutral DBs when MCBs to be used 8,way 230 V double door with 200 Amps bus bar.Make:Legrand/Standard

S&F MCB single pole 6 A to 32 Amps, 10 KA Rupturing capacity C Curve 240 Volts complete all as specified.

M&L MCB single pole and Neutral 32 A 20 KA Rupturing Capacity 'C' curve 240 Volts complete all as specified.

M&L Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with earthing lead of 4mm dia galvanised iron or steel wire all as shown in Plate No. 2 to the earthing test point upto 7.5 mtr all as specified and indicated including testing, complete all as specified and directed by Engr-in-Charge. Note:- 1. Excavation and Earthwork and earthpit as specified shall be deemed to be included in the rate quoted.

ruturajconstruction

JAMNAGAR ELECTRIC AND MACHINERY CO