CERTAIN B/R REPAIRS TO MD ACCN IN SOUTHERN SECTOR UNDER AGE B/R-II AT MIL STN KOTA

Amount

Taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Dismantling floor, hearth or wall tiling/ terrazzo including cement mortar bedding (but not backing), removing tiles and rubbish off the premises, complete all as specified and directed.

Taking down chowkhat or frames not exc 1.50 Sqm each with shutters (with out taking off shutters from the frame), complete all as specified and directed.

Taking down chowkhat or frames exc 1.50 Sqm and not exc 4.00 Sqm each with shutters (with out taking off shutters from the frame), complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm & n. exc 2 Sqm each and refixing in same after easing and resecuring/adjusting of shutter including renewal of screws etc complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm & n. exc 2 Sqm each including renewal of screws etc complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors etc, laid, bedded and pointed in any mortar, complete all as specified and directed.

Taking down existing treatment of any description such as PCC, lime concrete, mud phuska etc. and any numbers of layers upto any thickness from roof including scraping and roughening old by picking, sweeping clean and washing down and removing debris outside MD land complete all as specified and as directed.

M&L for cleaning of walls and floor of sunken portions including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to IS: 3384 @ 0.40 Kg/Sqm, torching overlaps with a propane or a butane gas torch with an overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold applied bituminous primer all as per manufacturer’s instructions, complete all as directed. Note: (i) The waterproofing treatment shall be got carried out through the manufacturer or their authorized applicators only.

Providing & applying evenly a coat of industrial bitumen 85/25 @ 1.2 kg per sqm including cleaning over primed surfaced (interval between 1st & 2nd coat shall be as directed by Engineer-in-Charge) complete all as specified and as directed.

Supply only approved liquid water proofing compound, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F in renewal of stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) not exc 0.5 sq.m from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

M&L for 3mm thick figured glass, pin head type and glazing with oil putty in square not exc. 0.5 sq.m in each pane complete all as specified and directed.

S&F 3mm thick glass, ordinary quality and glazing with oil putty and glazing pins in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

M&L for 30mm thick FACTORY MADE MOULDED DOOR SHUTTER-WOOD FREE consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 25mm x 25mm for stiles, top and bottom rails. M. S. frame shall have a coat of steel primers. The inner panel shall consist of 25mm thick EPS of Density 23 Kg /Cbm. bonded with 2mm thick termite proof, water proof and fire resistant moulded PVC Sheet Manufactured by an ISO-9001-2015 certified company, with 2, 4, 6 raised panel design in different plain and / or prelam colours after routing the Moulded design on one side & 2mm plain and /or prelam PVC sheet on other side of the EPS. The edge of panel to be sealed with lipping of 15mm wide PVC sheet baton ( made by sticking 2mm rigid foam PVC sheets of 5mm (±0.25) thickness using PVC solvent cement ) and stile sides 25mm (5mm x 5nos.) thick and 30mm width PVC Sheet fitted along M.S. tube for hardware provision & for lock 25mm thick ( 5mmx5nos. ) PVC sheet of size 150mm x 200mm fixed with inner side of EPS Panel etc. complete all as per specifications and drawings as applicable to item 08103 given in SSR Part–II. MAKE :- Rajshri/Sintex/Accucel/Duraplast.

~Ditto~ all as per srl item No 17.00 (here-in-before) but wire gauged ie panel will be of wire gauze in lieu of wood grain printed PVC sheet panel. The wire gauze warped on additional square 8 mm M.S solid tube and this tube shall be welded to MS tube. The wire gauze shall be stretched to tighten firmlycomplete all as specified and directed. NOTE:- Wire mesh will be measured and paid separately.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. Make:-Rajshri/Sintex/Accucel/Duraplast.

S&f FOR Factory Made 30mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Flush Door Shutter of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade), Calcium Carbonate and natural fibers (Wood Powders/ rice husk/ wheat husk) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm manufactured by "RAJSHRI" an ISO 9001 - 2015 Certified Company, having good screw holding capacity (Screw Withdrawal strength of 2000 N (Face ) & 1100 N (Edge), Minimum Compissive of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer In-Charge, (Material test certificate and authentication should be compulsory provided by the manufacturing company) complete all as per specifications and drawings as applicable to item 08103 given in SSR Part–II. MAKE :- Rajshri/Sintex/Accucel/Duraplast.

S&F factory made steel windows conforming to IS-1038 with side hung shutters & including projecting type hinges, with 2 Nos steel handles, 2 Nos tower bolts & steel pag stay complete (with glazing bars), dovetailed or welded & including fixing of lugs in PCC 1:2:4, type B-1, using 20mm graded stone aggregate & making good walls & cills to match the existing and including one coat of red oxide/ zinc chrome primer complete all as specified and directed. Note :- Glass shall be measured and paid for sepparately under respective items.

S&F factory made steel windows conforming to IS-1038 with side hung shutters & including projecting type hinges, with 2 Nos steel handles, 2 Nos tower bolts & steel pag stay complete (without glazing bars), dovetailed or welded including fixing of lugs in PCC 1:2:4, type B-1, using 20mm graded stone aggregate & making good walls & cills to match the existing and including one coat of red oxide/ zinc chrome primer complete all as specified and directed. Note :- SS or MS cloth wire shall be measured and paid for sepparately under respective items.

S&F brass skeleton tower bolts with cast brass plate and staples and rolled or drawn brass bolt 375mm long and fixed, ISI marked complete all as specified and directed.

S&F 150mm size extruded brass handles, fabricated type polished and fixed, ISI marked complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed, ISI marked complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised 100 mm size, ISI marked complete all as specified and directed.

S&F 100 mm size mild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws, complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, with hard drawn steel spring, fixed in floor, overall length of cover plate 150 mm, complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F in renewal of 18 mm thick HDWPC (High density wooden plastic composite) kitchen cupboard/ door shutter board one side colour/white laminated and other side decorative as in modular kitchen/cabinets fixed with minifix hardware where ever required including edge band 22 mm wide .80 m thick of matching colour on exposed surface of board fixed with polymaster adhesive including trimming edges of edge band to true line of thickness of board by manual trimmer fixed to wall etc complite all as specified and directed. Make:- Pearl wood or equivalent in Rajshri plastiwood/ Greenply/ Century PLywood.

S&F in renewal of 18 mm thick HDWPC (High density wooden plastic composite) board one side colour/white laminated and other side decorative as in shelf and partition of cabinet complete all as specified and directed. Make:- Pearl wood or equivalent in Rajshri plastiwood/ Greenply/ Century PLywood.

S&F in renewal of factory made pressed steel cupboard shutters alongwith frame, frame made of 1.25 mm thick PBI sheet and shutter made of 1.00 mm thick PBI sheet with 6 Nos 3.15 mm thick and 100 mm long steel hinges per shutter, godrej pattern locking arrangement with 12 mm dia vertical rod and lock with duplicate key & chrome finish handle, duly spray painted in factory with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, complete with fastener, hold fast etc as required at site, complete all as specified and directed. (Total width including frame shall be measured for payment purpose).

S&F 125 mm Hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed.

S & F in renewal continuous (piano) hinges, stainless steel, matt or brush finish, width of flaps (when open) in 40mm complete all as specified and directed.

S&F in renewal ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggreate), 50 mm thick as in plinth protection/Path/PCC paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where dirtected and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight), complete all as specified & directed.

S&F mild steel framed work as in grills, grating etc. with end of bars shouldered and/or riveted, or forged into spikes: framed guard bars: barred iron doors: ladders: frame balusters: walk ways: railing: frame work of water tanks and similar works conforming to Fe-290 Grade-E-165, complete all as specified and directed.

S & F for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing & confirming to Fe.410W.Gde-E-250, quality-B complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed. Make :- Somany/AGL/ Kajaria/ Johnsons or techno commercially equivalent make as specified in PS.

M&L for joint free non skid matte finish ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed. Make :- Abrasio series of AGL/ Somany/ Kajaria/ Johnsons or techno commercially equivalent make as specified in PS.

M&L for joint free non skid matte finish ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm fixed on vertical surfaces, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 10 mm thick rendering in CM 1:4 backing, complete all as specified and directed. Make :- Abrasio series of AGL/ Somany/ Kajaria/ Johnsons or techno commercially equivalent make as specified in PS.

M&L Glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm/450X300X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in CM 1:4, complete all as specified and directed. Make :-SOMANY(GRANDE VEGAS FP, DURAGRES SERIES) / JOHNSON / KAJARIA (POLISH SERIES) / RAK or techno commercially equivalent make as specified in PS.

M&L black granite (of any type) slab 18-20 mm thick, table rubbed and mirror polished by applying wax polish as in cooking platform, jambs, cills, pillars, tread, risers, platform for WHB etc including bull nosing to exposed outer edges, set in CM 1:4 bedding and pointing with white cement mixed with pigment and provn of hole for gas pipe, laid over and including 20 mm thick screed bed in CM 1:6, complete all as specified and directed. Note :- Granite stone slab shall be laid in single piece with rounding of edges and a grove shall be provided beneath the projection portions of slab.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of ceiling in cement mortar 1:3 including finishing the surface even and smooth, complete all as specified and directed.

Material and labour for plastering 15 mm thick (in two layers i.e. 10 mm thick 1st layer and 2nd layer 5 mm thick) on fair faces of brick work or concrete surfaces (on vertical surfaces) mixed with water proofing compound as per manufacturer instructions in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and as directed. Note :- Liquid WPC shall be measured and paid separately.

M&L for preparing new previously untreated plastered surfaces of walls and applying two coats of distemper oil emulsion over & including a coat of chalk whiting, complete all as specified and directed.

M&L for applying three coats of white wash on ceiling including preparation of new or previously untreated surfaces, complete all as specified and directed.

M&L for applying one coat of white wash after preparation of old previously treated plastered surfaces of ceiling, complete all as specified and directed.

M&L complete removal of existing treatment from previously treated surfaces of walls and over it applying two coats of distemper oil emulsion, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of exterior emulsion paint over a coat of primer complete all as specified and directed. Note :- (i) All coats including primer to be applied with fully automatic airless spray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI / Manual application Allow 6-8 hrs to dry the surface in subsequent coats of paint. (ii) Make should be dulux weather shield max/Nerolac Excel Everlast 12/Asian paint ultima protek / Berger weather coat long life 15 or Techno commercially equivalent makes specified in PS.

Material and labour for complete removal of existing treatment for preparation of old surface of wall and applying two coats of exterior emulsion paint over a coat of primer complete all as specified and directed. Note :- (i) cracks of wall plaster should be filling upto 5 bars of positive hydrostatic pressure on vertical walls without any dilution with forced coverage not more than 3.5 sqm / ltr as per manufacturer's instructions. (ii) All coats including primer to be applied with fully automatic airless spray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI / Manual application Allow 6-8 hrs to dry the surface in subsequent coats of paint (iii) Make should be dulux weather shield max/Nerolac Excel Everlast 12/Asian paint ultima protek / Berger weather coat long life 15 or Techno commercially equivalent makes specified in PS. (iv) decorated treatment on wall / ceiling / chajja by scrapping with trucare wall sander : L-01/H-01 (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and filling cracks, holes etc .

M & L for preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of 1st grade quality over and including one coat of red oxide zinc chrome primer complete all as specified and directed.

S&F in renewal of 25mm dia, powder coated, fancy type, aluminium decorative tubular curtain rod with decorative ball type side brackets, complete all as specified and directed.

S&F in renewal PVC connection 450 mm long suitable for 15 mm GI pipe with two PTMT nuts and rubber washers complete all as specified and directed.

S & F in renewal of Bib taps 15mm dia, chromium plated, long body, with CP flange all as per fixed in repairs complete all as specified and as directed. Make :- CERA cat part No G 1017152 /Jaquar cat pat no VGP-81037/ Hindware cat part No F 740011 or techno commercially equivalent makes specified in PS.

S & F in renewal of 15mm bore two way angle valve chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed with necessary fitting complete all as specified and directed. Make :- CERA cat part No G1017211 / Hindware cat part no F 740006 / Johnson cat part no JT 1643A or techno commercially equivalent Make specified in PS.

S & F of pillar taps, 15mm dia, long body/swan neck, fancy type suitable for fixing to wash basin screwed for iron pipe and fixed with necessary fittings and including PVC connection complete all as specified and as directed. Make :- CERA Cat Part No F1003103 / Jaquar cat Part No COP -021PM/ Hindware Cat Part No F 740002 or techno commercially equivalent makes specified in PS.

S&F in renewal vitreous china wash hand basin, white, with flat back of size 550x400 mm, excluding chain and plug, taps and porcelain stopper but incl CP brass waste coupling of 32 mm bore, PVC waste pipe of 32 mm bore & one pair of 600 mm long cast iron brackets, complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 15 mm bore pipes complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 20 mm bore pipes complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) for 15 mm dia pipes with and including all new fittings complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) for 20 mm dia pipes with and including all new fittings complete all as specified and directed.

Supply, fixing, laying & testing 15 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

Supply, fixing, laying & testing 20 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

S&F in renewal of vitreous china squatting pan, 'Orissa' pattern size 580mm x 440 mm, white, with front or back inlet, integral foot rest, including 'P' or 'S' trap, incl providing lime concrete bedding and connecting to flusing cistern, complete all as specified and directed.

S & F in renewal of shower rose 125/150 mm size brass chromium plated with swivel joints including fixing steel pipe or unions with all necessary fittings complete all as specified and as directed. Make :- CERA cat part No F7020111AB/ Hindware cat part No F 160142/ Johnson cat part No JF 803899 or techno commercially equivalent Makes as specified in PS.

Supply and fix in renewal of PVC valveless, syphonic action type, flushing cistern, 10ltr capacity, low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes and fixing of chain and pull, or lever, complete all as specified and as directed. Make :- Cera Cat No. B1010102L/Johnson cat part No J 85821C or techno commercially equivalent makes specified in PS.

S&F in renewal of 75 mm bore PVC (SWR) floor trap, with stainless steel grating including jointing to waste pipe and fixed in cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) complete all as specified and directed.

S&F in renewal of sink with draining board made of stainless steel 1mm thick with plugs, washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets of suitable angle iron, 32 mm dia superior quality PVC waste pipe and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in renewal of stainless steel kitchen plate rack of size 1200x900x180 mm, made of 1.00 mm thick stainless steel sheet with partition for small /large plates and fixed in position, design and pattern as approved by the GE, complete all as specified and directed.

S&F in position rotational moulded polyethylene water storage tanks 500 ltrs capacity (cylinderical vertical with closed top) hoisted and fixed in position, ISI marked, including dismantling existing water storage tank of any description, complete all as specified in SSR Part I and as directed.

S&F of 20mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed (Minimum weight 20mm-210 gms) complete all as specified and directed.

S & F in renewal of towel rail 600mm long of CP fixed with screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and as directed. Make :- CERA Cat No.F5013104CH/Jaquar cat part No ACN-1111 SM/ Hindware cat part No F 450024 or techno commercially equivalent makes specified in PS.

Supply and fixing in renewal of 50mm bore, low density polyethylene pipes (LDPE) of pressure rating 6 kgf/Sqcm fixed to walls, ceilings or in floors etc complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints laid in trenches or in floor and including all fittings & including dismantling of old u/s existing pipes alongwith fittings and accessories complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and pavings n.exc 15 cm thickness (below or above GL) and removing rubbish from premises, complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in sub base of floors etc, finished fair and even to receive floor finishes complete all as specified and directed.

Providing and laying 60 mm thick factory made cement concrete interlocking paver block glossy finish of M35 grade conforming to IS 15658: 2021 made by block making machine with strong vibratory compaction, of approved size, design & shape, cast in rubber mould, glossy finish of approved colour, laid in required colour and pattern over and including 25 mm thick sand cushioning, compacted bed of coarse sand, filling the joints with fine sand etc. complete all as specified and as directed.

TARKESHWAR DASS CONSTRUCTION COMPANY (BID ID -3084678)

M/s Prem Associates (BID ID -3086053)

Aditya Enterprises (BID ID -3090032)

ANNAPURNA ENTERPRISES (BID ID -3088247)

Ganesh Contruction (BID ID -3090816)

SINGH ENTERPRISES (BID ID -3088638)