PROVN OF GUARD ROOM ALONGWITH TOILET AND BATHROOM NEAR PT ELECTRICAL ITEMS AT FVT BARODA

Amount

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation, etc or for the shafts, well, cesspits, manholes, pier holes, etc n exc 10 Sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil complete.

All as per item No-1 above but depth exe. 1.5 m & n. exc 3.0m

Surface excavation not exceeding 30 Cm deep and averaging 15 cm deep and getting out in soft / loose soil complete.

Returning, filling in, including spreading, leveling, watering & well ramming in layer s not exc 25 cm in hard /dense soil complete.

Removing excavation material exe. 50m but n exc. 500m & deposited where directed at a level n exc. 1.5m above the starting point complete

M&L Cement concrete in foundations, filling and mass-concrete type D2 1:4:8 (40 mm graded aggregate) complete

M&L for Used and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams; and similar work; rough finished surfaces of concrete flat etc. complete.

M&L for used and waste formwork to sides of pillars, posts, struts, piers, coumns and stanchions etc. Squires, rectangular etc. rough finished surfaces of concrete complete

M&L for used and waste formwork to sides of Roof Beam or lintel beam . Squires, rectangular etc. rough finished surfaces of concrete complete.

M&L for used and waste formwork to fin or facia or sides of concrete flat rough finished surfaces of concrete complete.

M&L for used and waste formwork to soffits of suspended slab such as roof slab floor slab, landing and similar work rough finished surfaces of concrete complete

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to Fe -500D complete.

All as per item No 12 above but 5 mm dia and over upto and including 10mm dia in stirups, spaces and binders

M&L for reinforced cement concrete work (design mix) M-25 with using 20mm graded stone aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. complete

M&L for reinforced cement concrete work (design mix) M-25 with using 20mm graded stone aggregates as in beams,(Roof Beam or Plinth Beam) cantilievers, bressumers over 1.5 mtr, lintel Beam including chajja complete

M&L for reinforced cement concrete work (design mix) M-25 with using 20mm graded stone aggregates as in columns, pillars, piers, posts and struts complete.

M&L for reinforced cement concrete work (design mix) M-25 with using 20mm graded stone aggregates as in Roof Slab complete

M&L for reinforced cement concrete work (design mix) M-25 with using 20mm graded stone aggregates as in Fin/Facia complete

M&L for brick work with sub class "B" bricks old size brick straight or curved on plan exc 6m mean radius, built in CM 1 : 6 complete

M&L for brick work with sub class 'B' bricks built in CM (1:4) straight or curved on plan to any radius in half brick thick walls with old size bricks complete.

M&L for plain Cement concrete type B1 1:2:4 using 12.5 mm graded aggr as in DPC complete

M&L for rendering 10mm thick on fair faces of Internal bricks surface or concrete surfaces with CM 1:4 complete

M&L for rendering 10mm thick on fair faces of concrete surfaces on ceiling with CM 1:4 complete

M&L for rendering 15mm thick on other than fair faces of External bricks or concrete surfaces with CM 1:4 complete

Supply only integral water proofing compound @ 3% of weight of cement complete.

M&L 75 mm thick plain cement concrete (PCC) type C2 1:3:6 (40mm grade aggregate) as in plinth protection complete

M&l for hardcore of guage n. exc 63mm, deposited, spread & leveled in layers n exc. 15cm thick,watered & rammed to a true surface complete

M&L 75 mm thick plain Cement concrete (PCC) type D2, 1:4:8 (40mm grade aggregate) as in sub base complete

M&L for plain cement concrete (PCC) 100mm thick type B-2 1:2:4 (40mm graded aggrete) as in approach path laid in alternate pannels used waste of form work/screed and to dividing the area in panel, finished even and smooth complete.

M&L for prepararion of new plsatered surface of wall and applying two coats of cement base paint over a coat of cement base primer complete

M&L for pre-pararion of new plsatered surface of wall and two coats of distemper over one coat of alkali resistant primer complete.

M&L applying 1-1.5 mm thick wall care putty on new surface of wall complete.

M&L preparing new plastered surfaces of ceiling and applying three coats of white wash complete

M&L for preparing new steel surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrom primer complete .

M&L surface preparation of new wooden surfaces of any description, not otherwise described, over 10cm width or grith and apply two coats of synthetic enamel paint over a coat of pink primer complete

M&L for 165x60 mm pressed steel door frames for doors with one or more rebates including necessary fixing lugs, hinges, locks strike plates etc. Complete

M&L for 105x60 mm pressed steel door frames for doors with one or more rebates including necessary fixing lugs, hinges, locks strike plates etc. Complete

S&F factory made 35mm thick 2nd class HW plain, framed, panelled shutters (two panels), with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), cleaned seasoned and chemically pressure treated complete .

S&F factory made 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, cham-fered or rounded, mitred and rebated sash bars, any numbers and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. cla-use 8.20 (a); supplied and fitted to chowkats complete.

S&F of Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. Complete

S&F of Powder coated aluminium window / ventilator shutters, side hung / sliding type aluminium sections including necessary joining cleats, sash bars, glazing clips rubber neoprene packing, anodised aluminium snap beading, screws and aluminium grill etc as per manufactures instruction & trade practice complete.

S&F mild steel bars conforming to Fe 290 Gde E-165 as in guard bars or similar works including welding etc complete.

S&F 4.00mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete

S&F 4.00mm thick figured glass, pin head type and glazing with oil putty in square n exc 0.5 sqm in each pane complete

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete

S&F Mild Steel bands, straps, supports or holdfasts etc and similar small articles conforming to Fe 310-O or Fe 410-O complete

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent cement, supply & fixing in the frame at site as per SSR specifications & diagram/product drawing shown on sl page NO 146 of SSR Part II with the size of door shutter as required complete.

S&F factory made solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as per specifications and as per drawing shown on sl page No 150 of SSR part II (for item-884) complete

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete

S&F 200mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete

S&F Butt hinges, Medium weight, cold rolled mild steel, and fixed 100mm size complete

S&F 200mm size aluminium anodised, barel tower bolt of extruded section complete.

S&F 150mm size aluminium anodised, barel tower bolt of extruded section complete.

S&F 150mm aluminium alloy handles, fabricated type anodised complete

M&L for Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor over all lenth of cover plate 150mm complete.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete incl screed bed or bedding layer of cm 15mm thick for laying floor finishes with CM 1:6 complete

M&L for machine cut kota stone slab 20 - 25mm thick in skirting, riser etc over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including screed bed or bedding layer of mortar 10mm thick for laying floor finishes with CM 1:4 complete

M&L for Non Skid ceramic coloured tiles 7mm to 8mm thick, (square or rectangular) area of each tile exc 0.06Sqm but n. exc 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed in CM(1:6) complete

M&L for Non Skid ceramic coloured tiles 7mm to 8mm thick, (square or rectangular) area of each tile exc 0.06Sqm but n. exc 0.11 sqm in verticle surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in skirting including 10mm thick backing coat of tiles in CM(1:4) complete.

M&L for Glazed ceramic tiles coloured 300 x 200mm x 7mm thick, in vertical surfaces such as skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick backing coat of tiles in CM (1:4) complete

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including lime concrete bedding complete.

S&F PTMT square grating 150mm size for trap complete

M&L for Vitreous china wash hand basin white flat back 550 x 400 mm with pedestal of standard size including chromium plated brass waste coupling, waste pipe, vulcanite plug with ring, pillar taps, PVC connection of suitable length, brackets and cutting for & pinning in ends of brackets etc complete.

M&L for Vitreous china urinals, half stall type white complete incl providing and fixing plugs, bedding urinal against wall in CM (1:2), securing urinal to plug with & including 60 mm long brass screw, fixing flush pipe, brass CP grating and union for discharge pipe, PVC telescopic waste pipe of suitable length etc complete

M&L for 15 mm bore Steel water tubing, medium grade, galvanised with all tube fitting & including concealed in walls and ceiling or laid in floors including testing complete

M&L for 20 mm bore Steel water tubing, medium grade, galvanised with all tube fitting & including concealed in walls and ceiling or laid in floors including testing complete

S&F Bib tap cast copper alloy with crutch or butterfly handle screwed down, fancy type chromium plated screwed for 15 MM bore iron pipe or brass, ferrule & fixed complete.

S&F Stop valve, cast copper alloy, chromium plated fancy type handle, screwed down, high pressure with push type handle screwed for 15mm bore iron pipe and fixed complete.

M&L for Rotational moulded polyethylene (HDPE) water storage tanks, double layer (cylindrical vertical with closed top) capacity 1000 litres hoisted and placed in posiition on PCC platform complete

S&F for Towel rail 600 mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats complete.

M&L for soap dish, vitreous china white, fixed to plugs with chromium plated brass screws complete

S&F 125mm dia chromium plated shower rose with swivel joints including fixing to GI union complete

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with back fill to be measured) complete

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per squaremetre of surface

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete

M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete

S&F PVC valveless 10lts capacity syphonic action type flushing cistern low level, white with inlet, ball valve float and handle including brackets and 32 mm dia polyethylene waste pipe complete

S&F PVC connection 600mm long of dia 15mm complete.

S&F 75 mm PVC (SWR) pipes double socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F 110mm PVC (SWR) pipes double socketed, in any length with rubber ring joints, laid in trenches or in floors complete

S&F PVC (SWR) bends 75mm bore complete

S&F PVC (SWR) bends 110mm bore complete

S&F PVC (SWR) branch piece, single (single Y) equal or unequal, dia 75mm complete.

S&F PVC (SWR) branch piece, single (single Y) equal or unequal, dia 110mm complete.

S&F 75 mm PVC (SWR) 'P’ trap complete

S&F 110 mm PVC (SWR) 'P’ trap complete

S&F PVC (SWR) vent cowl 100mm dia complete

S&F 20 mm thick granite Stone for partion wall including necessary cutting work to vertical surfaces complete.

S&F 20 mm thick green granite Stone for window cill including necessary screed bed and match to pigment including rubbing and polishing and half round the edge complete.

M&L for 10 mm thick cement plaster (1:3) in CM with using water proofing compound @ 3% by weight of cement as per manufacturer's instructions complete . (WPC will be measured separately).

M&L for applying evenly a priming/tack coat with bituminous primer at 10 kg per 10 sq metre (Paving bitumin) complete.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete.

M&L for sand cushoning to cable with river sand and punning to provide required cover for UG cables complete

M&L brick protection cover to electric cable with sub class 'B' bricks laid dry and flat abutting each other with gap between adjascent not exceeding 10mm complete.

Supply and laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 25 sq. mm 4 Core nominal cross section in service connections complete .

M&L for galvanized steel tube light Grade of 40 mm dia protection of cable fixed to pole/walls with all necessary fittings and fixed with clamps, bolts, nuts and washers etc complete.

M&L for galvanized steel tube light Grade of 40 mm dia protection of cable laid in floors, road crossing ducts with all necessary fittings etc complete.

Supply and laying in trenches of GI steel tubing medium grade including all fittings such as Tees, elbow, bends etc for 20 mm bore of pipe complete.

S&F 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete.

S&F Cock, bib, brass chromium plated, screwed down For size 15 mm (1/2”) dia pipe complete

M&L for cutting existing steel tubing for alterations or additions (Each cut measured) and inserting new Tee, bend, elbow etc up to 20 mm dia complete

S&F CI bends (any type radius & angle), tappers any type (straight bend increasing or decreasing or double socket etc) tee pieces single branch ‘Y’ junction double branch cross (all sockets or socket & spigot) collars caps plug etc up to 150 mm bore for spigot & socket and socket pipes complete.

M&L brick masonary valve pit of size 750mm X 750mm X 750mm (internal dimension) with MS angle iron frame work size 40mm X 40mm X 6mm & 3mm MS sheet top cover openable through hinges including necessary locking arrangement, 50mm thk PCC type B1 1:2:4 with necessary formwork coping, 10mm thk rendering in CM 1:4 and painting with two coat of black bituminous paint over a one coat red oxide primer complete

Supply, installing, testing and commissioning factory made and tested LT feeder pillar box (KIOSK) outdoor type CPRI approved platform mounted, suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system having copper bus bar installed on DMC / Epoxy insulators. The panel shall be dust and vermin proof, IP-65 class protection and made of 3.15mm CRCA MS sheet with front opening type of 4'x3' size with double door shutter and locking arrangement, duly painted with powder coated finish over a coat of red oxide inside & outside surface. The TPN copper bus bar of rating not less than the 1.5 times (600 Amps capacity) the rated capacity of the incomer MCCB with following accessories :-

(i) Incoming MCCB 4P 160 Amp, 35 KA -01 No

(ii) MCB 4P 32 Amp, 35 KA -02 Nos

(iii) Outgoing MCCB 4P 100 Amp, 25 KA -02 Nos

(iv) Digital voltmeter & Ammeter with necessary CTs

(v) Internal wiring with PVC insulated, multi stranded copper conductor cable, 1100 V grade, IS 694 marked of approriate size but not less than 2.5 sqmm

(vi) Phase indicating LED lamps (R-Y-B) -01 set

(v) Over load relay Qty - 03 No

(vi) Diigital Frequency meter AC upto 60 HZ - 01 No

(viii) Fuse terminal Box - 01 No

(ix) Earthing Aluminiym Strip

Supply, installing, testing and commissioning factory made and tested LT feeder pillar box (KIOSK) outdoor type CPRI approved platform mounted, suitable for 415 volts 3 phase 4 wire , 50 Hz AC supply system having copper bus bar installed on DMC/Epoxy insulators. The panel shall be dust and vermin proof, IP-65 class protection and made of 3.15mm CRCA MS sheet with front opening type of 1'x1' with double door shutter and locking arrangement, duly painted with powder coated finish over a coat of red oxide inside & outside surface. The TPN copper bus bar of rating not less than the 1.5 times(400 Amps capacity) the rated capacity of the incomer MCCB with following accessories :-

(i) Outgoing MCCB 4P 63 Amp, 25 KA -03 Nos

(ii) Digital voltmeter & Ammeter with necessary CTs

(iii) Internal wiring with PVC insulated, multi stranded copper conductor cable, 1100 V grade, IS 694 marked of approriate size but not less than 2.5 sqmm

(iv) Phase indicating LED lamps (R-Y-B) -01 set

OCEAN CONSTRUCTION