Rejuvenation and Restoration of Sera Pond based on Natural Treatment System with in Tehsil Nadaun and Distt. Hamirpur HP

Clearing weeds including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth p to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared., within all lead and lifts as per direction of Engineer - in - charge.

Bailing out or pumping out sludge/ water during removal aquatic vegitation and weeds, within all lead and lifts as per direction of Engineer - in - charge.

Excavation in foundations and trenches (for pipes and pits for other civil structures) upto all depths in all kinds of soil such as pick work, jumper work and saturated soil and paved surfaces including bailing or pumping out of water, chiseling or wedging out of same where blasting is prohibited in all leads and lifts including trimming and dressing of sides, leveling of beds to correct grade including shoring, strutting, planking timbering and dewatering wherever required, stacking usable and unusable material/soil separately and after laying jointing and testing of pipes, returning the usable soil in 15 cm layer by ramming and watering and then disposing of all surplus excavated soil/unusable material as directed within all leads and lifts including cost of diversion of traffic, night signal boards, fixing caution boards, crossing over trenches for access to houses, fencing etc. complete in all respects as per the direction of Engineer-in-charge.

Providing form work with steel plated 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring,shuttering,strutting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor to ceiling not exceeding 4 meters and removal of the same for insitu-reinforced concrete and plain.

Foundation footing bases of column and mas concrete

Vertical surfaces such as wall (any thick.) partitions & the like i/c attached pillasters,buttresses,plinth & string courses & the like.

(a)Flat surfaces such as soffits of suspended floors, roofs, landings and the like floors upto 200mm kin thickness.

Providing and laying cement concrete 1:2:4(1cement:2sand:4 graded stone aggregate 20mm nominal size and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts.

Providing, Laying mild or tor steel reinforcement for RCC. Work including bending binding and placing in position complete upto floor two level Tor steel in all leads and lifts.

Supplying and spreading of good earth and consolidation with light power road-roller etc. complete at site including royalty within all lead and lifts as per direction of Engineer in charge

Supplying and spreading Geo-Liner/ Mamberane one mm thick within all lead and lifts as per direction of Engineer-in-charge.

Supplying and spreading of Ventonite slurry and consolidation with light power road-roller etc. at site complete in all respect within all lead and lifts as per direction of Engineer -in-charge.

Providing, fixing and Installation Fountain for Aeration System at site including carriage within all leads and lifts.

Providing plinth protection 50mm thick in cement concrete 1:3:6(1cement:3sand:6graded stone aggregate 20mm nominal size) including finishing of the top surface of concrete smooth as directed by the Engineer-in-charge in all leads and lifts.

Providing and fixing 3 layer 100mm nominal bore PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801 UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP-R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge.

Providing and fixing of submersible pumping set of Kirloskar/Lubi/KSB make Model with 2.00 HP motor comprising to latest relevant BIS Code. The pump should be fitted with Bronze impeller of suitable alloys as per IS 8034-1976 latest suitable for clear water having greased packed bearings and shaft with wound stator on motor side and with soft protection sleeve on pump side ensuring better life for shaft coupled to a submersible squirrel cage electric induction motor (water proof type) of 3.00 HP, RPM 2900 of KSB/Kirlosker/NGF/Crompton/Marathon make conforming to BIS 9238-1979 latest with upto date amendments, totally dust and water proof for submersible duty isolated from the pump by intermediate casing with double mechanical seal in oil chamber and grease packed lubricated bearings and provided with stainless steel thrust bearing plate to with stand non vertical loads with minimum wear and tear. It should also be fitted with a device to take up expansion of water with the heating of motor. The pump set should include water level guards, erection clamps , cable clips and depth gauge etc. and suitable for operation on data given below:-

Wire crate made of GI wire with boulder with square cut faces against the wire (boulders& nsquare cut faces against the wire (boulder filling to be measured and paid for separately).15cmX15cm mesh (GI wire 5mm thick corresponding to SWG 6)as per the entire satisfaction of the Engineer-in-charge

Wire crate made of GI wire with boulders & square cut faces against the wire (wire crate to be measured and paid for separately).

Providing bio-media of size 50–75 mm, consisting of 25–40 mm free-form dirt-free and dust-free material, duly washed, complete including all leads and lifts.

Supplying of potted plants at site including carriage within all leads and lifts.

Hibiscus (big)

Rubina Palm

Providing water fouls including all leads anf lifts.

Samll

Stone/Boulder filling retaining wall including all leads and lifts complete in all respect.

Steel work welded in built up section ,trusses & frames work including cutting,histing,fixing in position & applying a priming coat of red lead paint :- in Grating, framedGaurd,bars ,ladders, railing, bars, bracket & Similar work complete in all respect with in all leads and lifts.

Painting two coats(excluding priming coat)on new steel and other metal surfaces under coat with aluminium paint brushing to give and even shade including cleaning of all dirt dust and other foreign matter and sand papering and stopping with ready mixed paint other than white in all leads and lifts.

Dressing the ground including cutting and filling up to 15 cm, as per the direction of the Engineer-in-Charge, including carriage in all leads and lifts.

Providing and laying 80 mm thick cement concrete paver blocks of M-30 grade, of approved colour, design and pattern, factory-made with chamfered edges. The paver blocks shall be used in footpaths, parks, lawns, driveways or light traffic parking areas, of required strength, thickness and size/shape The blocks shall be manufactured by table vibratory method using PU moulds and laid in the required colour and pattern over a 50 mm thick compacted sand bed. Proper embedding and laying of interlocking paver blocks into the sand bedding layer shall be done through vibratory compaction using a plate vibrator. This includes filling joints with sand, cutting of paver blocks as per required size and pattern, finishing, sweeping of excess sand, and completion of the work as per the direction of the Engineer-in-Charge.

Providing and laying at or near ground level factory-made kerb stones of M-25 grade cement concrete, positioned to the required line, level, and curvature. The kerb stones shall be jointed with cement mortar in the proportion 1:3 (1 cement : 3 coarse sand). Making joints with or without grooves (joint thickness not exceeding 5 mm), Joints at sharp curves shall be without grooves, Providing drainage openings wherever required, Completing all work as per the directions of the Engineer-in-Charge.The length of finished kerb edging shall be measured for payment. Precast cement concrete kerb stones shall be approved by the Engineer-in-Charge.

Applying priming coat over new steel and other metal surface after and including cleaning the surface by thoroughly brooming oil, dust dirt grease and other foreign matter land papering and knotting ready mixed paint finishing hard primer pink)

Providing and laying cement concrete 1:1.5:3(1cement:1.5 sand:3 graded stone aggregate 20mm nominal size)and curing complete excluding the cost of form work in:-

In foundation , footing basis of columns and the like and mass concete in all leads and lifts.

Walls (any thickness) but not less than 0.10cm thickness including attached pilasters, buttresses, plinth and string courses from top of foundation upto all floor level as per direction and to the entire satisfaction of the Engineer-in-charge.

Suspended floors roofs,landing and shelves and there supports beams.etc

Supplying and erection of 4-metre-high decorative poles made of galvanised mild steel pipes, fitted with cast aluminium/iron embellishments, duly polyurethane paint coated. Specifications: Base plate: 300 × 300 × 10 mm Bottom diameter: 139.7 mm (1 m) Top diameter: 76.1 mm (3 m) Foundation nuts & bolts: MFHD-203 2.5-inch pipe fitted on top portion of the pole Work includes fixing only (without wiring )

Providing and laying of one No. copper conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade direct in ground; to be laid 1 meter below the ground level including excavation sand cushioning, protective covering and refilling the trench etc. of the required size: - Armoured cable 10 sq. mm (twin core).

Supplying and errection of LED Post Top Lights BGCTNP 40W WW on Pole of apprved brand and manufecture including all accessories at site including carriage within all leads and lifts.

supplying and errection of fency. Light. CLaddi Type 6.00ints. Length around the pole form bottm to top approved brand and manufecture i/c accessores at site il camiage within all lads and lifts.

Rough dressing of trenched ground including breaking clods

Fine dressing of the trenched ground

Supplying and stacking of good earth at site including royalty and carriage up to 100 metres by head load and 1 km by mechanical transport (earth measured in stacks shall be reduced by 20% for payment)

Supplying and stacking manure at site including royalty and carriage up to 100 metres by head load and 1 km by mechanical transport (sludge measured in stacks shall be reduced by 8% for payment)

Spreading sludge dump manure and/or good earth in required thickness (cost of sludge/dump manure and/or good earth to be paid separately)

Grassing with Doob grass in rows 5 cm apart in either direction including watering and maintenance of lawn for 30 days or more till grass forms a thick lawn free from weeds and fit for mowing, including supplying good earth if needed (cost of Doob grass to be paid separately)

Supplying and planting of potted plants at site including carriage within all leads and lifts

(a)Golden Unifresh

Gycus Palm

Rubenia Palm

Hibiscus (Big)

Supplying and erection of Fency LED lights mounted on MS/GI pole of approved brand and manufacture, including all accessories at site, including carriage within all leads and lifts.

Supplying and fixing of signage boards with flex printing on tubular section frame of required size and shape, including writing of water conservation slogans, complete with all accessories at site, including carriage within all leads and lifts.

Providing and laying Spartic ceramic tiles, 5.5 mm thick, in flooring of 600 × 600 mm size treads of steps, laid on a bed of 12 mm thick cement mortar 1:3 (1 cement : 3 sand).

Providing and fixing 0.60 mm thick pre-painted steel sheet in roofing, with hot-dipped metallic zinc-coated sheet having:Top coat of regular modified polyester (RNP) organic coating of 20 microns primer coating of 5 microns Back coat of polyester of 5 microns over 5 microns primer coatingIncluding fixing with pre-painted iron J or L hooks, bolts and nuts, 6 mm diameter, metre washers, complete with all accessories as required, as per the direction of the Engineer-in-Charge.

Providing and fixing ridges or hips, 60 cm overall width, with 0.60 mm thick pre-painted steel sheets in roofing, with hot-dipped metallic zinc-coated sheets having: Top coat of regular modified polyester organic coating of 20 microns Primer coating of 5 micronsBack coat of polyester of 5 microns over 5 microns primer coatingIncluding fixing with pre-painted iron J or L hooks, bolts and nuts (6 mm dia), pre-painted G.I. limpet and bitumen washers, complete with all accessories as required, as per the direction of the Engineer-in-Charge.

Brick work using common burnt clay building bricks in foundation and plinth level upto floor two level in cement mortar 1:4(1cement:4sand) 2nd class brick

Half Brick work using common burnt clay building bricks in super structures in cement mortar 1:4(1 Cement:4 sand) including carriage of materials and curing complete in all leads and lifts.(2nd class)

20mm Cement plaster in single coat on rough side of brick/stone masonry forinterior plastering upto floor two level includingarrises,internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth.(1:4)

Providing and laying granite stone in flooring 20mm (average) thickness base ofcementmortar 1:3 (1cement:3 sand) laid over and jointedwithgrey cement slurry mixed withpigment to match the shade ofgranite stone i/c rubbing andpolishing complete. 20mm.thick

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and placing in horizontal layers filtering media duly graded, screened, washed and cleaned as specified by the Engineer-in-Charge.

laying in trenches, galvanized mild steel tubes (Medium grade), tube fittings (earth work in trenches to be measured & paid for separately).100mm dia

Providing and fixing of 3.15mm MS Sheet Manhole cover 600X600mm fixed on all sides with ISA 40x25x5mm top angle iron frame hinged on ISA 35x35x5mm bottom angle iron frame as per drawing. Pieces of MS Flat 20x4mm, 0.15m long be fixed on all sides as hold fast. The operation of manufacturing shall including cutting of MS Sheet, Angle Section & welding of MS Sheets, Angle Section, Hinges, Handles 150mm long, 20x4mm flats, locking arrangement and applying a priming coat of steel primer after pretreatment of surface to the entire satisfaction of the Engineer-in-Charge.

Supply of submersible pumping set of Kirloskar/Lubi/KSB make Model with 3.00 HP motor comprising to latest relevant BIS Code. The pump should be fitted with Bronze impeller of suitable alloys as per IS 8034-1976 latest suitable for clear water having greased packed bearings and shaft with wound stator on motor side and with soft protection sleeve on pump side ensuring better life for shaft coupled to a submersible squirrel cage electric induction motor (water proof type) of 3.00 HP, RPM 2900 of KSB/Kirlosker/NGF/Crompton/Marathon make conforming to BIS 9238-1979 latest with upto date amendments, totally dust and water proof for submersible duty isolated from the pump by intermediate casing with double mechanical seal in oil chamber and grease packed lubricated bearings and provided with stainless steel thrust bearing plate to with stand non vertical loads with minimum wear and tear. It should also be fitted with a device to take up expansion of water with the heating of motor. The pump set should include water level guards, erection clamps , cable clips and depth gauge etc. and suitable for operation on data given below:- (Fountain)

For fountain

Providing and fixing a cluster jet fountain made of SS 304 grade, 450 mm diameter, capable of achieving a water effect height up to 30 meters, of Make: Raj or equivalent, as per the entire instructions, directions, and satisfaction of the Engineer-in-Charge.

Providing and fixing a float with one part, anchored from two sides, made of SS 304 grade body metal sheet, with foam filling. Color to be as per the Engineer’s instructions.Bending / threading / fixing / welding to be completed All fixing work shall be carried out as per directions, instructions, and to the entire satisfaction of the Engineer-in-Charge.

Providing, installation, testing, and commissioning of a submersible pump set with shaft sleeves and thrust bearing, having all rotating parts dynamically balanced for smooth operation Suitable for three-phase, 50 Hz AC supply, as per directions and instructions of the Engineer-in-Charge. Motor Body: SS Pump Body: SS Make: Lyra Solar Pump Capacity: 3 HP, Three Phase Suction & Delivery: 100 mm

Cable

Solar Panel: PV Power 335 Watt

Accessories

Installation Charges

Provision for structural and drawings @2%