Repair of 2nd, 3rd and 4th Floor of Science Block, currently in the possession of District Ayurvedic Hospital at Nahan, Sirmaur (HP)

Amount

Demolishing cement concrete manually/ by mechanical means including disposal of materials within all leads, lifts & as per direction of Engineer-in-Charge nominal concrete 1 : 3 : 6 ( One cement : three sand : six graded stone aggregate ) or richer mix ( including equivalent design mix ), including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable materials & disposal of unserviceable materials within all leads,lifts & as per direction of Engineer-in-Charge, in cement mortar, including all leads, lifts , carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Dismantling doors, windows & clerestory windows ( steel or wood ) shutters including Chowkhats, architrave, holdfasts etc. complete & stacking within all leads, of area 3.00 Smt ( Three point zero zero square metres ) & below including all leads,lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Dismantling doors, windows & clerestory windows ( steel or wood ) shutters including Chowkhats, architrave, holdfasts etc. complete & stacking within all leads, of area beyond 3.00 Smt ( Three point zero zero square metres ), including all leads,lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains in all heights and depths in all kinds of soil, including saturated soil comprising of pick work,jumper work and blasting work both in soft and hard rock with chiesling and wedging out of rock (where blasting is prohabited) and their intermediate classification of soil including dewatering whereever required,settling out to required lines,levels as shown on the drawing and directed by the Engineer in charge at site according to the HP.PWD specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (to be arranged by the contractor) including payment of prescribed dumping charges of M.C. if levilled any to the satisfaction of the Engineer in charge through all modes of transporation including head load animal load or mechanical means alongwith its levelling, fine dressing and with all kinds of labour, mechineries, tools, equipment and safety measures and incidental necessary to complete the work by mechanical means and labour (if required). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transporation and used/removed as per the satisfaction of the Engineer in charge. any loss to the public and private properity during the course of execution and disposal of servicable and unservicable materials shall be the absolute responsiblity of the contractor and shall have to be duly compensated by him in all respects including all incidential charges and as directed by the Engineer in Charge:- All kinds of soil.

Filling in plinth with sand under floors including watering ramming consolidating and dressing complete as per HP.PWD., specification 1990 volume-I ( one ) including carriage of all labour equipments and materials to various location through all leads, lifts and other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing and laying in position cement concrete of specified grade mechanically mixed and curing complete excluding the cost of centering and shuttering - All work up to plinth level and all floor level in 1:4:8 (one Cement : four coarse sand : eight graded stone aggregate 40mm (forty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Making plinth protection 50 mm ( fifty milimetre ) thick of cement concrete 1 : 3 : 6 ( One cement : three coarse sand : six graded stone aggregate 20 mm ( twenty milimetre ) nominal size ) over 75 mm ( seventy five milimetre ) thick bed of dry brick ballast 40 mm ( forty milimetre ) nominal size, well rammed & consolidated & grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying in position cement concrete of specified grade mechanically mixed , vibrated & curing complete excluding the cost of centering, shuttering, finishing & reinforcement - All work up to plinth level and all floor level in 1:1.5 : 3 (One Cement : One & half coarse sand : five graded stone aggregate 20mm (twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying reinforced cement concrete work in walls (any thickness), mechanically mixed, vibrated and curing complete including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor all level , excluding cost of centering, shuttering, finishing and reinforcement in 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20mm ( twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor all level mechanically mixed, vibrated and curing complete, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20mm ( twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing form work with steel plates 3.15mm ( three point fifteen millimeter ) thick welded with angle iron in frame 30X 30X5mm ( thirty X thirty X five millimeter ) so as to give a fair finish including centering ,shuttering, strutting and propping etc. with wooden battens and ballies , height of propping and centering below supporting floor to ceiling not exceeding 4.00 meters ( four meters ) and removal of the same for insitu- reinfoced concrete and plain concrete work including all leads and lifts of materials or as per the directions of Engineer in Charge.

Foundations, footings, bases of columns, etc. for mass concrete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Walls (any thickness) including attached pilasters, buttresses, plinth & string courses etc.including all leads, lifts & carraiage of materials & to the entire satisfaction of the Engineer-in-Charge .

Suspended floors, roofs, landings, balconies and access platform including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Lintels, beams, plinth beams, girders, bressumers and cantilevers including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Edges of slabs and breaks in floors and walls Under 20cm ( twenty centimeter ) wide including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and placing steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding wire all complete upto floor all level. Thermo-Mechanically Treated bars of grade Fe-500 D or more including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation & plinth in all shapes and sizes in Cement mortar 1 : 6 ( One cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes in Cement mortar 1 : 6 (one cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes : Cement mortar 1 : 4 ( One cement : four coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing 18 mm ( eighteen milimetre ) thick gang saw cut, mirror polished, premoulded & prepolished, machine cut for kitchen plateforms,vanity counters, window sills, facias & similar locations of required size, approved shade, colour & texture laid over 20 mm ( twenty milimetre ) thick base cement mortar 1 : 4 ( One cement : four coarse sand ), joints treated withwhite cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, coulding & polishing to edges to give high glass finish etc. complete at all level Granite of any colour, shade & all area of slab including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Marble work gang saw cut ( Polished & machine cut ) of thickness 18 mm ( Eighteen milimetre ) for wall lining ( Veneer work ), backing filled with a grout of average 12 mm ( twelve milimetre ) thick in cement mortar 1 : 3 ( One cement : three coarse sand ), including pointing with white cement mortar 1 : 2 ( One white cement : two marble dust ) with an admixure of pigment to match the marble shade ( To be secured to the backing by means of cramps, which shall be paid for separately ) Granite of any colour & shade & area of slab over 0.50 ( Zero point five zero ) Square metres, including all leads, lifts & carriage of materls & to the entire satisfaction of Engineer-in-Charge.

Providing and laying Ceramic glazed wall tiles of size 300mm x 450 mm ( three hundred millimeter X four hundred fifty millimeter ) (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except burgundy, bottle green, black of any size as approved by the Engineer-in-Charge in Skirting, risers of steps & dado over 12 mm ( twenty millimeter ) thick bed of cement mortar 1:3 (one Cement : three Coarse sand) and jointed with grey cement slurry @ 3.3kg/ sq.m (three point three zero kilograme per square meter ) including pointing in white cement mixed with pigment of matching shade complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium sliding door bolts, ISI marked anodised ( Anodic coating not less than grade AC 10 as per IS:1868 ), transparent or dyed colour to required colour or shade, with nuts & screws etc. complete 300 x 16 mm ( three hundred into sixteen milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium sliding door bolts, ISI marked anodised ( Anodic coating not less than grade AC 10 as per IS:1868 ), transparent or dyed colour to required colour or shade, with nuts & screws etc. complete 250 x 16 mm ( two hundred fifty into sixteen milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 200 x 10 mm ( two hundred into ten milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 100 x 10 mm ( One hundred into ten milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium handles ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 125 mm ( one hundred twentyfive milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium handles ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 100 mm ( one hundred milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium hanging floor stopper ISI marked anodic coating not less than grade AC 10 as per IS: 1868 ) transparent or dyed to required colour & shade, with necessary screws etc. complete Single rubber stopper including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium hanging floor stopper ISI marked anodic coating not less than grade AC 10 as per IS: 1868 ) transparent or dyed to required colour & shade, with necessary screws etc. complete Twin rubber stopper including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand ) logo with ISI, IS:3564, embossed on the body, door weight upto 35Kg ( Thirty five kilogram ) door with upto 700mm ( seven hundred milimetre ) with necessary accessories & screws etc. complete, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing Cub board shutters 19 mm ( nineteen milimetre ) thick with pre-laminated flat pressed three layers particle board or graded wood particle board IS: 12823 marked exterior grade ( Grade I type II ) , having one side decorative lamination & other side balancing lamination, including second class teak wood lipping of 25 mm wide 12 mm thick ( twenty five milimetre wide twelve milimetre ) thick ) with necessary screws & bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing decorative high pressure laminated sheet of plain/ wood grain in gloss /matt/ Suede finish with high density protective surface layer & reverse side of adhesive bonding quality conforming to IS: 2046 Type-S, including cost of adhesive of approved quality 1.00 mm ( One point zero zero milimetre ) thick sheet including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing 19 mm ( Nineteen milimetre ) thick water proof commercial board in shelves/box for Cub board with butt joints & fixing with nails & screws etc. complete, including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing ply wood 4 mm ( four milimetre ) thick, one side decorative veneer conforming to IS: 1328 (Type-1 ), for plain lining/ cladding with necessary screws, including priming coat on unexposed surface with decorative veneer facing of approved manufacture including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing special quality bright finished brass cub board or ward robe locks with four levers of approved quality including necessary screws etc. complete 50 mm ( fifty milimetre ) size, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing 50mm ( fifty milimetre ) bright finished brass cub board or ward robe knob of approved quality with necessary screws, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing magetic catcher of approved quality in Cub board/ ward robe shutters, including fixing with necessary screws etc. complete double trip ( horizontal type ), including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing expandable fasterners of specified size with necessary plastic sleeves & galvanised mild steel screws including drilling holes in masonry work/ cement concrete/ reinforced cement concrete & making good etc. complete 40 mm long, including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Structural steel work riveted, bolted or welded in built up sections, trusses & framed work,including cutting, hoisting, fixing in position & applying a priming coat of approved steel primer all complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing mild steel round holding down bolts with nuts & washers plates complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing 3 mm thick & 26 centimetre wide Aluminium sheet in expension joints in vertical & horizontial of R.C.C. columns & flooring complete in all respect, including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Mirror polished Kotah stone slab flooring over 20 mm ( twenty milimetre ) ( average ) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing & polishing complete with base of cement mortar 1 : 4 ( one cement : four coarse sand ) 19 mm ( ninteen milimetre ) thick, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Mirror polished Kotah stone slab 20 mm ( twenty milimetre ) thick in risers of steps, skirting, dado & pillars laid on 12 mm ( twelve milimetre ) ( average ) thick cement mortar 1 : 3 ( One cement : three coarse sand ) & jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing & polishing complete, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & laying vitrified double charge floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08 % & conforming to IS 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1 : 4 ( One cement : four coarse sand ), jointing with grey cement slurry @ 3.3 Kilogram per square metres including grouting the joint with white cement & matching pigments etc. complete size of tile 600 x 600 mm, including all leads, lifts, & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & laying vitrified double charge tiles in different sizes ( thickness to be specified by manufacturer ) , with water absorption less than 0.08 % & conforming to IS 15622, of approved make, in all colours and shade, in skirting, riser of steps, over 12 mm ( Twelve milimetre ) thick bed of cement mortar 1 : 3 ( One cement : three coarse sand ), jointing with grey cement slurry @ 3.3 Kilogram per square metres including grouting the joints with white cement & matching pigments etc. complete size of tile 600 x 600 mm ( Six hundred into six hundred milimetre ) ,including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Cement concrete flooring 1 : 2 : 4 ( One cement : two coarse sand : four graded stone aggregate ) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm ( forty milimetre ) thick with 20mm ( twenty milimetre ) nominal size ) stone aggregate including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Cement plaster skirting upto 30 cm ( thirty centimetre ) height, with cement mortar 1 : 3 (One cement : three sand) finished with a floating coat of neat cement 18 mm ( eighteen milimetre ) thick, including all leads, lifts, carriage of materials to the entire satisfaction of the Engineer-in-Charge

Providing & fixing glass strips in joints of terrazo/ cement concrete floors 40 mm wide & 4 mm ( forty milimetre wide & four milimetre ) thick, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing 0.60 mm ( sixty milimetre ) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP ) organic coating of 20 ( twenty ) microns over 5 ( five ) microns primer coting to back coat of polyster of 5 ( five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6 mm ( six milimetre ) dia metre with prepainted limpet & rubber washers complete with all accessories as required as per the direction of Engineer-in-Charge, including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing ridge or hips 0.60 cm ( sixty centimetre ) over all with thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyster organic coating of 20 ( twenty ) microns over 5 ( five ) microns primer coting plus back coat of polyster of 5 ( five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6 mm ( six milimetre ) dia and prepainted G.I. limpet & rubber washers complete with all accessories as required as per the direction of Engineer-in-Charge, including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing valley 60cm overall 0.60 mm ( sixty milimetre ) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 ( five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6 mm dia with prepainted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing polycarbinated transparent sheet 1.20 mm ( One point two zero milimetre ) thick in roofing with galvanised J or L hooks bolts & nuts with G.I. Limpet & bitumen rubber washers complete with all accessories as required as per the direction of Engineer-in-Charge, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing 30 cm ( thirty centimetre ) wide 120 cm ( one hundred twenty centimetre ) overall Box type prepainted Zinc coated sheet gutter with iron bracket 40 x 3 mm ( forty into three milimetre ) size, bolts & nuts and washers etc. including making necessary connections with rain water pipes complete as per design. 0.45 mm ( forty five milimetre ) thick, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing flat iron bracket 50 x 3 mm ( Fifty into three milimetre ) size with necessary bolts, nuts & washers etc. for fixing galvanised steel sheets gutters with purlins including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing mild steel B.P. sheet 1.66 mm to 2 mm ( One point six six milimetre to two milimetre ) thick in eaves board/ facia/ soffits/ ceiling including cutting, fixing & welding to steel roof members & applying a coat of red lead primer complete as per the instruction of Engineer-in-Charge ( Base member of steel work shall be measured & paid for separately ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing false ceiling at all height including providing & fixing of frame work made of special sections, power pressed from mild steel sheets & galvanised with zinc coating of 120 ( one hundred twenty ) gramme per square metre ( both side inclusive ) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6mm ( twenty five milimeter into one point six milimetre ) thick with flanges of 27 mm and 37 mm, at 1200 mm ( twenty seven milimetre, thirty seven milimetre , at 0ne thousnd two hundred milimetre ) centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm ( Twelve point five milimetre dia into fifty milimetre ) long with 6 mm ( six milimetre ) dia bolts, other flange of cleat fixed to the angle hangers of 25 x 10 x 0.50 mm( twenty five into ten into zero point five zero milimetre ) of required length with nuts & bolts of required size & other end of angle hanger fixed with intermediate galvanised iron channels 45x15x0.90mm ( forty five into fifteen into zero point nine zero milimetre ) running at the spacing of 1200mm ( One thousand two hundred milimetre ) centre to centre, to which the ceiling section 0.5 mm ( zero point five milimere ) thick bottom wedge of 80 mm ( eighty milimetre ) with tapered flanges of 26 mm ( twenty six milimetre ) each having lips of 10.5 mm, at 450mm ( ten point five milimetre, at four hundred fifty milimetre ) centre to centre, shall be fixed in a direction perpendicular to galvanised iron intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm ( two point six four milimetre dia into two hundred thirty milimetre ) long galvanised iron wire at every junction, including fixing perimeter channel 0.5mm ( zero point five milimetre ) thick 27mm ( twenty seven milimetre ) high having flanges of 20 mm and 30 mm ( twenty milimetre & thirty milimetre ) long,the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm ( twenty five milimetre ) long dry wall screws @ 230 mm ( at the two hundred thirty milimetre ) interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm ( three point five into twenty five milimetre at two hundred thirty milimetre ) centre to centre, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes finishing with jointing compound in three layers covering upto 150 mm ( one hundred fifty milimetre ) on both sides of joint & two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawing, specification & direction of the Engineer-in-Charge but excluding the cost of painting with ACP Sheets of approved shade 60 x 60 cm ( Sixty into sixty centimetre ) , including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

15mm ( fifteen millimeter ) cement plaster on the rough side of single or half brick wall of mix : 1:6 (one cement: six fine sand) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

15mm ( fifteen millimeter ) cement plaster on the rough side of single or half brick wall of mix : 1:4 (one cement: four fine sand) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & applying plaster of paris putty of 2 mm ( two milimetre ) thickness over plastered surface to prepare the surface even & smooth complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Distempering with oil bound washable distemper of approved brand & manufacture to give an even shade new work ( two or more coats ) over and including water thinnable priming coat with cement primer including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing walls with Acrylic smooth exterior paint with of required shade new work ( two or more coat ) applied @ 1.67 litre/10 Sqmt ( one point six seven litre per ten square metres ) over & including priming coat of exterior primer applied @ 2.20 Kg /10 Sqmt ( at the rate two point two zero kilograme per ten square metre ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications,two or more coats applied on walls @ 1.25 ltr/ 10sqm( One point two five litre per ten square meter ) over an under coat including one coat of special primer applied @ 0.75 ltr/ 10sqm( zero point seven five litre per ten square meter ) of approved brand and manufacture complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10sqm( zero point nine zero litre per ten square meter ) over an under coat of primer applied @ 0.80 ltr/ 10sqm( zero point eight zero litre per ten square meter ) of approved brand and manufacture complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium work for doors, windows, ventilators & partitions with extruded built up standard tubular sections/ appropriate Z sections & other sections of approved make conforming to IS : 733 & IS : 1285, fixing with dash fasteners of required dia & size, including necessary filling up the gaps at junctions, i.e. at top, bottom & sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth,rust free, stright, mitred & jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per Architectural drawings & the direction of Engineer-in-Charge ( Glazing, panelling & dash fasteners to be paid for separately ) For fixed portion, Powder coatd aluminium ( minimum thickness of powder coating 50 micron ),including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing aluminium work for doors, windows, ventilators & partitions with extruded built up standard tubular sections/ appropriate Z sections & other sections of approved make conforming to IS : 733 & IS : 1285, fixing with dash fasteners of required dia & size, including necessary filling up the gaps at junctions, i.e. at top, bottom & sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth,rust free, stright, mitred & jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per Architectural drawings & the direction of Engineer-in-Charge ( Glazing, panelling & dash fasteners to be paid for separately ) For For shutters of doors, windows & ventilators including providing & fixing hinges/Pivots & making provision for fixing of fittings whereever required ,including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing glazing in aluminium doors, windows, ventilators shutters & partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the Atchitectural drawing & the direction of the Engineer-in-Charge ( Cost of aluminium snap beading shall be paid in basis item ) with float glass panes of 5mm ( five milimetre ) thickness ( weight not less than 12.50 Kg/Sqmt ), ( Tweelve point five zero kilogram per square metre ) including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing 12 mm ( Twelve milimetre ) thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Ty[pe II, in panelling fixed in aluminum doors, windowss shutters & partition frames with C.P. brass/ stainless steel screws etc. complete as per Architectural drawing & direction of Engineer-in-Charge, pre-laminated particle board with decorative lamination on both side, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/ pattern, with approved standard section & fixed to the existing window frame with C.P. brass/stainless steel screws @ 200 mm ( two hundred milimetre ) centre to centre, including cutting the grill to proper opening size for fixing and operation of handles & fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. (Only weight of grill to be measured for payment), including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing panelling or panelling and glazing in panelled or panelled & glazed shutters for doors, windows and clerestory windows ( Area of opening for panel inserts excluding portion inside grooves or rebates to be measured).Panelling for panelled or panelled & glazed shutters 25 mm to 40 mm ( twenty five milimetre to forty milimetre ) thick , Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching beading, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm ( one hundred millimeter ) sand cast Iron P or S trap, 10 litre ( ten litre ) low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge: White Vitreous china Orissa pattern W.C. pan of size 580mm x 440mm ( five hundred eighty millimetre X four hundred forty millimeter ) with integral type foot rests.

Providing & fixing white Vitreous China pedestal type water closet ( European type W.C. pan ) with seat & lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device ( handle lever ) Universal Pan No. 2061 size 570 x 460 mm , ( Five hundred seventy into four hundred sixty milimetre ) with all fittings & fixures complete including cutting & making good the walls & floors wherever required W.C. Pan with ISI marked white soild plastic seat & lid, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing white Vitreous China flat back half stall urinal of size 630 x 420 x 390 mm ( six hundred thirty into four hundrded twenty into three hundred ninety milimetre ) with white PVC auotmatic flusing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with union & clamps ( all in C.P. brass ) with waste fitting as per IS : 2556, C.I. trap with out let grating & other couplings in C.P. brass, including painting of fittings & cutting & making good the walls & floors wherever required Range of two half stall Urinals with 5 litre P.V.C. automatic flushing cistern, including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15mm ( fifteen millimeter ) C.P. brass pillar taps, 32mm ( thirty two millimeter ) C.P.brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- White Vitreous China wash basin size 550mm x 400mm ( Five hundred fifty millimeter into four hundred millimeter ) with single 15mm ( fifteen millimeter ) C.P. Brass pillar tap .

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing stainless steel Kitchen sink No. KCG 1012 ( Size 810 x 450 mm ) ( Size eight hundred ten into four hundred fifty milimetre ) with C.I. brackets & stainless steel plug 40 mm ( forty milimetre ) including painting of fittings & brackets, cutting & making good the walls wherever required kitchen sink with bowl depth 200 mm, including all leads,lifts,carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing stainless steel A ISI 304 ( 18/8 ) kitchen sink as per IS: 13983 with C.I. brackets & and stainless steel plug 40 mm ( forty milimetre ) including painting of fittings & brackets, cutting & making good the walls wherever required kitchen sink with drain board 460 x 385mm ( four hundred sixty into three hundred eighty five milimetre ) bowl depth 200 mm ( two hundred milimetre ) , including all leads, lifts, & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing and fixing 600mm x 450mm ( Six hundred millimeter into four hundred fifty millimeter ) beveled edge mirror of superior glass (of approved quality) complete with 6mm ( six milimetre ) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing 600mm x 120mm x 5mm ( Six hundred millimeter into one hundred twenty millimeter into five millimeter ) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm ( forty millimeter ) long screws, rawl plugs etc., complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing C.P. brass toilet paper holder complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing PTMT liquid soap container 109mm ( one hundred nine millimeter ) wide, 125mm( one hundred twenty five millimeter ) high and 112mm( one hundred twelve millimeter ) distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 125gms ( one hundred twenty five grams ) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providuing & fixing PTMT towel rail complete with brackets fixed to wooden cleats with C.P. brass screws with concealed fittings arrangement of approved quality & colour, 450 mm ( Four hundred fifty milimetre ) long towel rail with total length of 495 mm, 78 mm ( Four hundred ninety five milimeter, seventy eight milimetre ) wide & effective height of 88 mm ( eighty eight milimetre ) , weighting not less than 170 ( One hundred seventy ) grams including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre ( one metre ) spacing. This includes testing of joints complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- 1216 (16 mm ( sixteen millimeter ) OD) pipe.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre ( one metre ) spacing. This includes testing of joints complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:-1620 (20mm ( twenty millimeter ) OD) pipe.

Providing and fixing G.I. pipes complete with G.I. fittings & Clamps including making good the walls etc. concealed pipe including painting with anti corrosive bitumastic paint, cutting & making good the walls including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. internal work:-15mm ( fifteen millimeter ) dia nominal bore.

Providing and fixing G.I. pipes complete with G.I. fittings including making good the walls etc. concealed pipe including painting with anti corrosive bitumastic paint, cutting & making good the walls including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. internal work :- 20mm ( twenty millimetre ) dia.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.External work:-15mm ( fifteen millimeter ) dia nominal bore.

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- 25 mm to 40mm ( twenty five millimeter to forty millimeter ) nominal bore.

Fixing water meter & stop cock in G.I. pipe line including cutting & threading the pipe & making long screws etc. complete ( Cost of water meter & stop cock to be paid separately ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS : 8931, complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. 15mm( fifteen millimeter ) nominal bore .

Providing and fixing C.P. brass stop cock ( Concealed ) of standard design & of approved make conforming to IS : 8931, complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. 15mm( fifteen millimeter ) nominal bore .

Providing and fixing C.P. brass angle valve for basin mixer & geyser point of approved quality conforming to IS : 8931, complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. 15mm( fifteen millimeter ) nominal bore .

Providing & fixing C.P. brass extension nipple ( size 15 mm x 50 mm ( fifteen milimetre into fifty milimetre ) of approved make & quality as per direction of Engineer-in-Charge including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20mm ( twenty millimeter ) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40mm ( forty millimeter ) nominal size), inside plastering 12mm ( twelve millimeter ) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20mm ( twenty millimeter ) nominal size) finished with a floating coat of neat cement complete as per standard design complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. : Inside size 90cm x 80cm and 45cm ( Ninety centimeter into eighty centimeter and forty five centimeter ) deep including C.I. cover with frame (medium duty) 455 x 610 mm ( Four hundred fifty five into Six hundred ten millimeter ) internal dimensions, total weight of cover and frame to be not less than 38 kg ( thirty eight kilogram ) (weight of cover 23 kg ( twenty three kilogram ) and weight of frame 15 kg( fifteen kilogram ) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.50.

Providing & fixing high pressure PVC spigot & socket, waste & ventilating pipes ISI marked including fixing with approved adhesive etc. complete 150mm dia ( One hundred fifty milimetre ) including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing high pressure PVC spigot & socket, waste & ventilating pipes ISI marked including fixing with approved adhesive etc. complete 100 mm ( One hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing high pressure PVC spigot & socket, waste & ventilating pipes ISI marked including fixing with approved adhesive etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC door bend with oval access door, insertion rubber washer 3 mm ( three milimetre ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete 150 mm ( one hundred fifty milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC door bend with oval access door, insertion rubber washer 3 mm ( three milimetre ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete 100 mm ( one hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC door bend with oval access door, insertion rubber washer 3 mm ( three milimetre ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC collars ISI marked including fixing with approved adhesive etc. complete 150 mm ( One hundred fifty milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC collars ISI marked including fixing with approved adhesive etc. complete 100 mm ( One hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC collars ISI marked including fixing with approved adhesive etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete 150 mm ( One hundred fifty milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete 100 mm ( One hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC double equal branch with oval access door, insertion rubber washer 3mm ( Three milimetre ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete 150 mm ( One hundred fifty milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC double equal branch with oval access door, insertion rubber washer 3mm ( Three milimetre ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete 100 mm ( One hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC double equal branch with oval access door, insertion rubber washer 3mm ( Three milimetre ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC clamps ISI marked of approved design with steel screws & rawal plugs etc. complete 150 mm ( One hundred fifty milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC clamps ISI marked of approved design with steel screws & rawal plugs etc. complete 100 mm ( One hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC clamps ISI marked of approved design with steel screws & rawal plugs etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC reducer ISI marked including jointing with approved adhesive etc. complete 150 mm x 110 mm ( One hundred fifty milimetre into one hundred ten milimetre ) dia, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC reducer ISI marked including jointing with approved adhesive etc. complete 110 mm x 75 mm ( One hundred ten milimetre into seventy five milimetre ) dia, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive cost of cutting & making good the wall & floors etc. complete 110 mm x 90 mm ( One hundred ten milimetre into ninety milimetre ), including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive cost of cutting & making good the wall & floors etc. complete 110 mm x 75 mm ( One hundred ten milimetre into seventy five milimetre ), including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing 15 mm ( fifteen milimetre ) mixer for kitchen sink with top/ bottom swining spouts, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Cutting holes to 30 x 30 cm in walls including making good the same with common burnt clay F.P.S. ( Non modular ) bricks, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing 8 mm ( eight milimetre ) dia C.P./S.S. Jet with flexible tube upto 1.00 ( One ) metre long with S.S.triangular plate to Eureopean type W.C. of quality & make as approved by Engineer-in-Charge, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing in position precast reinforcement coment concrete manhole cover & frame of required shape & approved quality LD- 2.5 ( Two point five ) square shape 450 mm ( four hundred fifty milimetre ) internal dimensions including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing in position precast reinforcement coment concrete manhole cover & frame of required shape & approved quality LD- 2.5 ( Two point five ) rectangular shape 600 x 450 mm ( six hundred into four hundred fifty milimetre ) internal dimensions including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Supplying & filling brick bats in dispension trenches ( Brick aggregate ( Single size ) 50 mm ( Fifty milimetre ) nominal size ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing and fixing on wall face PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion, Single socketed pipes complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- 75 mm ( Seventy five millimeter ) diameter metre.

Lal Singh Chauhan Contractor

Mohan Singh