SPECIAL REPAIRS TO BLDG NO. T 83 STORAGE BUILDING AND PROVN OF SANITARY BLOCK AND TOILET AT VAIROUS LOCATIONS AND PROVN OF ARRANGEMENT FOR DRYING CLOTHES AT MIL STN DHRANGADHRA

Amount

Surface excavation not exceeding 30cm and averaging 15 cm deep and getting out in hard and dense soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in soft/disintegrated rock complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in hard/dense soil complete all as specified and directed.

Excavating in trenches not exceeding 1.5m wide and exceeding 1.5 m but notin depth for foundation of pole, laying of cables etc in hard/dense soil and getting out.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified and directed.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in soft/disintegrated complete all as specified and directed.

M&L for providing dry river sand as in sand cushioning to UG cable including punning gently all as directed. Note: Depth after punning shall be measured and paid.

Removing excavated material (soil), not exceeding 50m and depositing where directed at level not exc 1.5m above the starting point complete all as specified and directed.

Removing of excavated material exc 500m but n.exc 1.0km and depositing where directed.

M&L for hard core of gauge not exc. 63mm deposited spread and levelled in layers not exc. 15 cm thick, spread, levelled and rammed to a true surface including watering complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for plain cement concrete (1:4:8) type D2 using 40 mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed.

M&L for cement concrete (1:2:4) type B2, using 40 mm graded stone aggregate as in surface channels and drains, benching, haunching etc. complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate in coping and the like including necessary form work, all as specified and directed.

M&L for providing cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate in cpings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, finishing even and smooth without using extra cement, all as specified and directed.

M&L for Pre-cast cement concrete (1:2:4), type B1, using 20mm graded stone aggregate, solid block in kerb stone of size 300mm x 300mm x 75mm, with plain fair faces, including chamfers, weathering, throating etc and set in cement mortar (1:6) complete all as specified and directed.

M&L pre-cast reinforced cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate as in kitchen platform, shelves , cover and simillar articles including placing the cover in position and set in cement mortar (1:4) complete all as specified and directed. Note: Reinforcement shall be measured and paid seperately.

M&L for reinforced cement concrete, (nominal mix), type B1, 1:2:4 using 20mm graded stone aggregate as in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. basement slabs and mass cocrete complete all as specified and directed.

M&L for reinforced cement concrete, (nominal mix), type B1, 1:2:4 using 20mm graded stone aggregate as in chajjas complete all as specified and directed.

M&L for reinforced cement concrete, (nominal mix), type B1, 1:2:4 using 20mm graded stone aggregate as in beams, cantilevers, bressumers, lintels over 1.5m span complete all as specified and directed.

M&L for reinforced cement concrete, M-25 (design mix) using 20mm graded stone aggregate as in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. basement slabs and mass cocrete complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20 mm graded stone aggregate as in chajja etc complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20 mm graded stone aggregate as in beam, cantilevers, bressumers, lintels over 1.5m span complete all as specified and directed.

Supply only, integral water proofing compound.

M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L for cutting holes into or through stone walls built in cement mortar or cement lime mortar and walls of cement concrete having superficial area exc 150 Sqcm but n.exc 400 Sqcm complete all as specified and directed.

Supply and laying sub class old 'B' burnt bricks, size of brick 230x115x75mm, laid as cable protection cover complete all as specified and directed.

M&L for walling of random rubble stone masonry, uncoarsed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto course with maximum depression on face from straight edge held against the dressed surface not.exc. 20mm for sand stone complete all as specified and directed.

M&L for Form work to sides of concrete foundations, footings, base of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams etc for rough finished flat surfaces complete all as specified and directed.

M&L for form work to chullah hoods, chajjas , troughs and simollar items including edges and rough finished surfaces of concrete all as specified and directed.

M&L for form work to sides and soffit of floor or roof beams, beams haunchingss, girders, brussummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc and rough finished surfaces of concrete all as specified and directed.

S&F 35 mm thick, 2nd class hard wood factory made, plain, framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specifications complete all as specified and directed.

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed

S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300 mm and fixed complete all as specified and directed.

S&F, butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified and directed.

S&F, 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars, shouldered and/or riveted, or forged into spikes, framed guard bars etc and similar work conforming to Fe-290 (Gde-E-165) including applying one shop coat of red oxide primer complete all as specified and directed

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars, 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bend to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for MS rolled sections (Fe 410-W (Gde-E-250) quality-A) as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates

M&L for rolled mild steel angle iron work as in door frames complete, drilled for fixing of hinges etc. also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and directed.

S&F, factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded including applying one shop coat of red oxide primer complete all as specified and directed.

S&F, factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded including applying one shop coat of red oxide primer complete all as specified and directed.

S&F, factory made steel ventilators with top hung shutter including hinges, steel peg stay, glazing bars including applying one shop coat of red oxide primer all as specified and directed

S&F, pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, pre-painted galvalume aluminium zinc coating GI based plain steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, in repair, false ceiling, at any height, 600 x 600mm grid with Armstrong 'Prelude XL 32' grid system and 16mm thick mineral fibre acoustic tile 'RH - 99 Classic lite' with suspension system complete all as specified and per manufacturer's instruction. Make : Armstrong or equivalent as approved by GE.

M&L for 50mm thick cement concrete (1:3:6) type C1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L for 75 mm thick cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in sub base of flooring/hard standing, path and finishing the surface even and fair without using extra cement complete all as specified and directed.

M&L for Coloured glazed ceramic tiles of size 300 x 200 x 7mm thick, on vertical wall surface, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350 x 250 x 7mm/ 450mm x 350mm x 7mm on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including cement plaster 10mm thick in cement mortar (1:4) , complete all as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L, for machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658- 2006 of 60mm thickness, M-35 grade including 25mm thick sand cushion below paver blocks complete all as specified and directed.

M&L for preparing of new plastered or un-plastered wall surfaces and applying two coats of oil bound distemper over and including chalk whiting on plastered surfaces, preparatory to distempering complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on stone masonry surface or surface other than fair face of brick work finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) on walls/ floors surfaces mixed with using water proofing compound @ 3% by weight of cement or as per manufacturer instructions, finished even and smooth without using extra cement to receive WPT complete all as specified and directed. Note:- Supply only water proofing compound shall be measured and paid separately.

M&L for rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick cement plaster 1:4 on stone masonry surface or surface other than fair face of brickwork surface finished even and smooth without using extra cement.

M&L for rendering 20mm thick cement plaster 1:4 on stone masonry surface or surface other than fair face of brickwork surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered or un-plastered walls surfaces and applying three coats white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coat of cement base paint over a coat of white cmement putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement as primer complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of old plastered or un-plastered surfaces and applying two coats of oil bound distemper over and including one coats of wall care putty complete all as specified and directed.

M&L for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc. 0.5sq.m in each pane complete all as specified and directed.

M&L for 3mm thick figured glass, ordinary quality and glazing with oil putty in square not exc.0.5 sq.m in each pane complete all as specified and directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of new steel surface of any description not exc. 10cm width or girth and applying one coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 25mm bore of pipe complete all as specified and directed.

S&F, chromium plated over head shower 100mm dia round shape single flow (ABS body chrome plated with Gray face plate) with rubit cleaning system complete all as specified and directed as per Cat No. EOS-542N of ESSCO or equivalent make approved by GE from the make specified in Appx 'C'.

S&F, 32mm bore, low density polyethelene pipe (HDPE) of pressure rating 6kgf/sq.cm fixed to walls, ceilings or in floors etc. complete all as specified and directed.

S&F, 40mm bore high density polythene pipes (HDPE) of pressure rating 6 Kg/Sqcm fixed complete to walls, ceiling or in floors etc.

Supply, hoisting, fixing in position and connecting,500 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top), ISI marked, including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size and 20mm dia PTMT ball valve all as specified in SSR Part-I complete all as specified and directed.

Supplying, hoisting, fixing in position and connecting, 1000 litres capacity rotational moulded polyethylene water storage tank (cylindrical, vertical with closed top) including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed.

S&F, in repair, bib taps, cast copper alloy, fancy type, chromium plated, screwed down, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed.

Supply only, pillar tap, cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered 'hot' or 'cold' with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

Supply only, pillar taps cast copper alloy with capstan head, chromium plated, fancy type, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

S&F, stop valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed.

S&F, 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight -210 Gms)

S&F, waste coupling of PTMT (half or full threaded) minimum weight 45gms of 32mm bore of discharge pipe suitable for urinals complete all as specified and directed.

S&F, in repairs, towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all asa specified and directed.

S&F, PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F, 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor complete all as specified and directed.

S&F, 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor/walls complete all as specified and directed.

S&F, 75mm bore PVC (SWR) bend, any radius, with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) bend, any radius, with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) branch piece, single(Single Y) equal or unequal complete all as specified and directed.

S&F, 75mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR), vent cowl complete all as specified and directed.

S&F, PVC (SWR) floor trap, with chromium plated grating including jointing with solvent cement, dia of outlet 75mm complete all as specified and directed.

S&F, PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 150mm bore of pipe complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 200mm bore of pipe complete all as specified and directed.

M&L for salt glazed stone ware drain pipes, 150mm internal diameter, grade 'A' laid in trenches and jointed complete all as specified and directed.

M&L for salt glazed stoneware drain pipes, 200mm internal diameter, grade 'A' laid in trenches and jointed complete all as specified and directed.

Cutting into existing manholes for connecting new drain pipes, making good to pipes and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cment concrete (1:2:4) type B1, using 20mm graded stone aggregate, smooth finished and reforming benching as required for 150mm bore of pipe complete all as specified and directed.

S&F, vitreous china squatting pan, 'Orissa pattern, white of size 580mm x 440mm with integral foot rest, P or S trap (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F, 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed.

S&F, vitreous china wash basin, white, flat back of size 550mm x 400mm including brackets grouted in cement mortar 1:2 in wall complete all as specified and directed. Note :- Supply only pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately.

S&F in repair, vitreous china bowl urinal flat back, of size 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing flush pipe grating and union for discharge pipe and spreader with pipe (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F, in repair, vitreous china wash down water closet pan (Pedestal pattern), white with 'p' or 's' trap (excluding flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc. with seat and cover complete all as specified and directed.

S&F, in repairs, brass chromium plated shower rose with or without swivel joint, 125mm size complete all as specified and directed.

S&F, in repair, Soap dish, vitreous China white, approximate size 160x 160x90mm any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F, 32mm dia High density poythelyne (HDPE) pipes of pressure rating 6kgf/sqm as in waste pipe for urinal, sink, etc

Dismantling wall and ceiling boads (fibre, pulp, insulation etc.) or insulation boards/ slab/ blankets, any thickness including aluminium snap grid complete all as specified and directed.

M&L for wiring with and including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in and including medium grade PVC casing and capping double lock type 32mm in size, fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. complete all as specified and directed for the following :-

(a) One light/fan point controlled by one switch

(b) One 3 pin, 5 Amps, socket outlet on the same board controlled by another switch.

(c) One multi pin 5 Amps, socket outlet on Independent board.

M&L for wiring with and including multistranded copper conductor 4 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number in and including medium grade PVC casing and capping double lock type 32mm in size, fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. for one 3 pin, 15 Amps socket outlet point on independent board complete all as specified and directed.

S&F, in repair/replacement, LED light fitting, batten type, 1 x 18 watt including lamp and connecting up complete with white PVC insulated and PVC sheathed round flexible twin core copper conductor cable of suitable size and testing on completion all as specified and directed. Make : Bajaj or equivalent make in Havells.

S&F, lamp holder, PVC/Polycarbonate, with back plate suitable for batten fittings complete all as specified and directed

S&F, switch piano, flush button, single pole, one way, 5 Amps complete all as specified and directed

S&F, switch piano, flush button, single pole, one way 15 Amps complete all as specified and directed

S&F, socket outlet, 2 in 1, 3 pin, 15 Amps and 5 Amps flush type complete all as specified and directed

S&F, socket outlet, 2 in 1, 3 pin, 5 Amps, flush type complete all as specified and directed

S&F, LED lamp 9 watt suitable for batten fitting complete all as specified and directed.

S&F, box type fitting 1x16 Watt, blue coloured end caps, prewired for LED tube including LED tube 16 watts, including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Make of fitting as per Cat Part No. DMLN1LT8-16 of Crompton Greaves and for tube light LTT8-16 of Crompton Greaves or equivalent make approved by GE from the make specified in Appx 'C'.

S&F, in repairs, sheet metal distribution board, factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200 A tinned copper bus bar of capacity 200 Amps of SPN, 4 way 240 Volt complete all as specified and directed

S&F, ceiling rose, 3 terminal , any shade, of PVC/Polycarbonate, isolated body complete all as specified and directed

Supply and laying or passing through pipe, insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 6 sqmm 2 core complete as all specified and directed.

Supplying and laying, GI pipe, 40mm dia, light grade, laid under road, fixing to poles / walls with necessary clamp and taking out existing unserviceable pipe complete all as specified and directed.

Supplying & laying, in repairs, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire heavy duty underground cable with aluminium multi stranded conductor, 1100 volt grade, laid in trenches/duct, passing through pipe/duct or fixed on pole and connecting and testing complete including taking down old unserviceable cable all as specified and directed of 10 Sqmm, 2 core sizes of cable.

S&F in repair angle holder, insulated body with back plate for batten fitting complete all as specified and directed.

S&F, Exhaust Fan, 300mm Sweep, single phase, 230/240 volts, 50 Hz, including making opening for exhaust fan including grouting nut , bolts and washer for fixing of fan and making good the disturbed surfaces all as per existing and mounting fan including connected with three core copper conductor cable 0.75mm complete all as specified and directed .

S&F, miniature circuit breakers, type curve ‘B’ , 10 KA, SP, 6 to 32 Amps complete all as specified and directed.

S&F, isolator, Single pole, 5-40 Amps 230 Volts. complete all as specified and directed.

S&F, in repair of miniature circuit breakers, single pole and neutral type ‘C’ 10KA, 32/40 Amps 240 Volts. complete all as specified and directed.

S&F, Bulk head light fitting, 1 x 10 watt with polycarbonate housing Aluminium gear tray duly prewired inbuilt LED module IP-64 Protection complete with all accessories internally prewired and including connecting up with twin core flexible copper conductor of size 1.5 sqmm complete as all specified and directed. Make : Havells/Phillips/CG/C&S

S&F, box type fitting 1 x 16 watt blue coloured end caps prewired for LED tube including LED tube rod 16 watt including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Make Crompton Greaves fitting Cat part No. DMLN1T816 and for LED Tube LTT8-16 OR equivalent make in Havells/Philips

S&F, LED building security light fitting 1 x 12 watt watt with polycarbonate housing, aluminium gear tray duly prewired inbuild LED module IP-65 protection complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of size 1.5 sqmm including GI tubing 40mm dia light grade 105m long band to shape for mounting of security light with 2 no MS, FI clamp including plinth with nut bolts etc complete all as specified and directed. Make CG Cat Part No. LSTN-12 CDL OR EQUIVALENT make of Havells/Phillips.

S&F, in repairs, sub-main wiring with 2 single core, 4 Sqmm PVC insulated, unsheathed, 1100 Volts grade, FRLS, copper multi stranded conductor drawn in and including PVC concealed conduit and conduit acessories including drawing one run of PVC insulated, unsheathed, 1100 Volts grade, FRLS, copper conductor multi stranded, 2.5 Sqmm size as continuous earth wire drawn through and connected to main switch/DB and testing on completion complete all as specified and directed. Note: (i) 2 runs of main conductor, one run of earth conductor and one run of PVC conduit and acessories shall be measured as one unit length.(ii) Rate quoted shall deemed to includes cuttings chases for consealing PVC conduit and making good the disturbed surfaces in CM 1:3 complete.

M&L,earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth wire of 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I all as specified and testing on completion including provision of earth lead protected by 15 mm dia light grade GI pipe & watering pipe shall be 20 mm bore medium grade GI pipe including all excavation and earth work in any type of soil, PCC pit with RCC cover, char coal, salt, funnel etc complete. Note : Rate quoted by tenderers shall be deemed to include for following provisions;-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 M.[ii]. PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing lead from earth electrode to test point upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 15 mm bore light grade 7.5m.

Shree Builders