Contract KBC 08- Architectural and finishing works including Block work, Plumbing and other interior works of Five elevated metro stations (Civil Station Junction, Cochin S.E.Z., Chittethukara, Kinfra Park and Infopark) for Phase-II of Kochi Metro

Amount

CONCRETE WORK

Foam Concrete - Providing and Laying of Foam Concrete under Raised Floor as/ of density 1200kg/cum

Filled floor - Providing and laying AAC blocks for filled flooring: Laying AAC blocks of approved size and quality over prepared sub-base using cement mortar or adhesive ensuring proper compaction and alignment. Blocks shall be properly aligned, joints filled, and surface leveled for flooring. Includes all materials, labor, curing, and necessary finishing as directed by the Architect-in-Charge.

Rebarring - Drilling & fixing 12mm bar, 120 mm depth with two-component, pour-grade polysulphide-based joint sealant for movement joints in concrete, resistant to weather, UV, and chemicals. Includes surface preparation, primer, backing rod, and application as per manufacturer’s specifications. Complete in all respects. Brand: Hilti or equivalent

MASONARY WORK

SOLID BLOCK WORKS

Solid Blockwork (200mm thick)- Providing and fixing precast cement concrete solid block (SIZE 300X200X200) with cement concrete 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required centering, shuttering etc. complete up to any height including making Openings for duct of any size & shape& Finishing the same. up to 6 m. Minimum M10 grade shall be ensured.

(i)Extra for lifting charges from 6m to 12m (Concourse level)

(ii)Extra for lifting charges above 12m (Platform level and above)

Solid Blockwork (150mm thick)- Providing and fixing precast cement concrete solid block (SIZE 300X200X150) with cement concrete 1:2:4 (1 Cement : 2 coarse sand : 4graded stone aggregate 20mm nominal size) including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required centering, shuttering etc. complete up to any height including making Openings for duct of any size & shape& Finishing the same. up to 6 m. Minimum M10 grade shall be ensured.

(i)Extra for lifting charges from 6m to 12m (Concourse level)

(ii)Extra for lifting charges above 12m (Platform level and above)

Solid Blockwork (100mm thick)- Providing and fixing precast cement concrete solid block (SIZE 300X200X100) with cement concrete 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required centering, shuttering etc. complete up to any height including making Openings for duct of any size & shape & Finishing the same upto 6m. Minimum M10 grade shall be ensured.

(i)Extra for lifting charges from 6m to 12m (Concourse level)

(ii)Extra for lifting charges above 12m (Platform level and above)

Plaster grooves on external surfaces- Making Grooves 20*6mm on internal/external wall plaster complete as per architectural drawing at any height rounded of internally within the groove to prevent sedimentation of dust and other particles keeping the alighnment straight

GRANITE WORK

Platform Edge -Providing and fixing flamed finish Sadarahalli grey /Cheema Pink granite stone (bull nosed) of size 1200x600x60 mm at platform edge level using 5mm thick approved thick bed adhesive as per specification over prepared base on 20mm (average) thick base of cement mortar in 1:4 (1 cement : 4 total aggregate- sand and 10mm single sized aggregate) using 43 grade cement, water reducing admixture as per ISO 9103:1999 and jointing with white cement with matching colour pigment all complete in levelling course laid to proper slopes over screed base including, base preparation including movement joint in screed as per specification with 10mm thick compressible filler to edge of screed with two parts polysulphide sealant to top edge as per approved drawing and directions of Architect-in-charge.All Light color Granites to be fixed on White Cement.As per Approved Adhesive..Minimum Compressive strength shall be as per IS 1121(part 1) .Water absorption Test shall be carried out as per IS 1124.The flooring shall be covered with POP / Gypsum powder of 12mm thick /Plywood to ensure that the flooring is not damaged till the construction work is completed and handed over.

Granite for Corridor & Rooms -Providing and laying 30mm thick prepolished Sadarhalli Grey/ Cheema Pink/ Jhalore Beige granite slab of sizes up to and including 1200X600mm on floor using 5mm thick approved thick bed adhesive as per specification over prepared base on 20mm (average) thick base of cement mortar 1:4 (1 Cement : 4 total aggregates - coarse sand and 10mm single sized aggregates) using 43 grade cement, water reducing admixture as per ISO 9103:1999 and jointing with white cement with matching colour pigment all complete (Colour of granite as approved by Engineer) in levelling course laid to proper slopes over screed base including base preparation, movement joint in screed as per specification with 10mm thick compressible filler to edge of screed/ block work junction with two parts polysulphide sealant to top edge, drainage gullies as per approved section, curing, testing etc. all complete as per specifications and approved drawings. Screed shall be measured and paid extra as per DSR 2018 item no 4.1.3.

Extra for Red/Raw silk/Jet Black/Tan Brown/Kashmir Yellow/ Ikon Brown/ Multi Red granite

Extra for Detailed / Intricate design floor pattern

Staircase Treads & Landing -Providing and laying 30mm thick FLAMED Sadarhalli Grey / Cheema Pink Granite Stone flooring in treads and landings (including bull nosing, rounding the nose and making groove) of steps of approved colour, size and pattern, (sample of granite stone shall be approved by Engineer-in- charge) over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4 core sand) laid and jointed with neat cement slurry mixed with pigment to match the shade of granite stone complete as per specifications and architectural drawings. Allow for cutting & finishing for handrails fixing as per design.All Light color Granites to be fixed on White Cement.As per Approved Adhesive..Minimum Compressive strength shall be as per IS 1121(part 1) .Water absorption Test shall be carried out as per IS 1124.The flooring shall be covered with POP / Gypsum powder of 12mm thick /Plywood to ensure that the flooring is not damaged till the construction work is completed and handed over.

Extra for Red/ Raw Silk/ Tan Brown/ Jet Black granite

Staircase Risers - Providing and laying 20mm thick mirror polished Granite Stone in Risers of steps of approved colour, size and pattern, (sample of granite stone shall be approved by Engineer-in- charge) over 12 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of granite stone complete as per specifications and relevant drawings.All Light color Granites to be fixed on White Cement.As per Approved Adhesive. Minimum Compressive strength shall be as per IS 1121 (part 1) .Water absorption Test shall be carried out as per IS 1124.The flooring shall be covered with POP / Gypsum powder of 12mm thick /Plywood to ensure that the flooring is not damaged till the construction work is completed and handed over.

Extra for Red/ Raw Silk/ Tan Brown/ Jet Black granite

TOM, EFO, SCR Counter and security room -Providing and installing counters of MS (with primer and 2 coats of enamel paint) carcass in TOM, EFO, SCR etc. with 30mm thick polished & moulded Jet Black Granite top (large slabs) with all cutouts/ openings including providing and fixing over RCC slab of minimum 100mm thick with granite lipping all complete of approved quality as per specifications and relevant drawings (Plan area shall be considered for measurement).

Platform parapet Coping -Providing & Fixing Polished Granite Coping over parapet / Kerb walls and sills of openings, bull-nosed on both edges over 20 mm thick cement mortar 1:4 (1 cement: 4coarse sand) with joint treated with white cement mixed with matching pigment including Rubbing, Curing , Moulding & polishing to edge to give high gloss finish etc. complete.

30 mm thick Jet Black granite

Granite wall Cladding- Providing and laying 30mm thick mirror polished Sadarhalli Grey/Cheema pink/Jhalore Beige granite stone work of up to and including sizes of 1200mm*600mm of approved colour/pattern with 4mm groove all around at all levels for wall linings/columns/skirting(veneer work) by mechanical arrangement with SS cramps/brackets (SS Grade 316), anchor bolts,5mm vertical SS pins (SS Grade 316) of approved make and inserts as per drawings and specifications. The cost of making necessary grooves all around stone pieces, chamfering of corner edges and polishing are included. Allow for cutting of holes and box outs for services etc. All Light color Granites to be fixed on White Cement.As per Approved Adhesive..Minimum Compressive strength shall be as per IS 1121(part 1) .Water absorption Test shall be carried out as per IS 1124.The flooring shall be covered with POP / Gypsum powder of 12mm thick /Plywood to ensure that the flooring is not damaged till the construction work is completed and handed over. Granite coping of projection 50mm and 30mm thickness (or as per drawing) shall be provided with chamfered or rounded edges, appropriate overhang, and drip grooves, fixed using mechanical anchoring or approved adhesive as per design and site conditions.

Extra for Red/ Raw Silk/ Tan Brown/ Jet Black granite

Granite Saucer Drain - Providing and laying 40mm thick polished granite slabs of approved shade (Cheema Pink / Red / Raw Silk / Jet Black / Tan Brown / Blue Pearl / Sadarahalli) over the drain trench as a cover. The slabs shall have 25mm diameter circular holes at 75mm centre-to-centre spacing for effective drainage. Granite shall conform to IS 1121 (Part 1) for minimum compressive strength and IS 1124 for water absorption. The installation shall include 1 inch x ½ inch L-shaped stainless steel (SS) sections fixed along the edges of the drain cutout as well as all edges of each granite slab, to provide structural reinforcement and a clean, finished appearance. The granite slabs shall be securely fixed to the SS supports using appropriate long-lasting, weather-resistant adhesives to ensure maximum stability and durability. All SS sections shall be precisely aligned and anchored, with necessary cut-outs provided wherever required.

FLOORING WORK

Vacuum Dewatered Flooring - Providing and laying Vacuum Dewatered Flooring including surface preparation, machine screeding, vacuum dewatering to remove excess water, mechanical trowelling for smooth finish, curing, and application of surface hardener (if specified), complete as per standard practices for durable, abrasion-resistant industrial flooring. The item is exclusive of concrete.

Grooves on floor surface - Cutting of grooves on concrete floor surface within 4 days after completion of laying of concrete as above using a power driven cutting machine and filling the grooves with polysulphide sealant as approved all complete and as directed. The width & depth of the groove shall be 5mm and 30mm respectively.

Tactile floor tiles - Providing and laying 12mm (minimum)thick with 3mm(minimum) thick projection on surface yellow coloured directional vitrified porcelain tactile tile of pelican or equivalent(as per specification)laid on floor with laterite 111 crete filler powder mixed with laterite 73 latex admix and applied to a minimum thickness of 4.5mm(The mixing ratio shall be as follows:20kg bag (laterite 111):5.5 liter (Laterite 73).Spacer of 3mm shall be used between the tiles and joints filled using Laterite Latapoxy SP-100 epoxy grout in Inca Gold colour. The joint depth shall be 6mm.Laticrete product shall be as manufactured by Laterite India Pvt.ltd/Laterite International Inc.)over 20mm thick bed of cement mortar 1:4(1 cement:4 coarse sand) in levelling course laid to proper slopes over screed base including base preparation including movement joint in screed as per specification with 10mm thick compressible filler to edge of screed with two parts polysulphide sealant to top edge as per approved drawings and directions of Architect-in-charge.

300*300 hazard warning and directional tactile tiles as per approved drawings

Platform Yellow strip- Providing and laying yellow visibility vitrified tile as per control sample of size 200*100*8 mm thick at platform level over 20mm thk bed of cement mortar 1:4(1 cement : 4 coarse sand) in levelling coarse laid to proper slopes over screed base including base preparation including movement joint in screed as per specification with 10mm thick compressible filler to edge of screed with two parts polysulphide sealant to top edge as per approved drawing and directions of engineer- in-charge.The tiles shall be free from objectionable surface blemishes such as projections, depressions, flakes, hairline cracks and bubbles. The tiles shall be level and regular in size with properly formed corners and shall not be warped or deformed in any manner laid at right angles as per design and pattern if required.The flooring/Tiles shall be covered with POP / Gypsum powder of 12mm thick /Plywood to ensure that the flooring is not damaged till the construction work is completed and handed over.

Vitrified tile skirting- Providing and fixing 1st quality 10mm thick Vitrified wall tiles of minimum 60cmx60cm size or higher and of approved make, conforming to IS :13755, The tiles shall be free from objectionable surface blemishes such as projections, depressions, flakes, hairline cracks and bubbles. The tiles shall be level and regular in size with properly formed corners and shall not be warped or deformed in any manner laid at right angles as per design and pattern if required,shade, colour and finish in all colours, shades, size in skirting, wall cladding, border tiles and dados over 20/12 mm thick bed of cement Mortar 1:4 (1 cement : 3 coarse sand)/ adhesive and jointing with approved adhesive and grouting material with pointing in epoxy grout of approved color & make. Joint width: 3 mm or as specified. The flooring/Tiles shall be covered with POP/ Gypsum powder of 12mm thick/ Plywood to ensure that the flooring is not damaged till the construction work is completed and handed over.

Anti dust Epoxy coating for Flooring- Providing and applying anti dust sealer (epoxy coating) 1000μ thick epoxy floor coating along with necessary floor preparation by approved manufacturer with use of two component, high solid, epoxy resin based floor primer @50 μ & then topcoat. Self levelling coatings with excellent flow & levelling characteristics, conforms to the Global Migration Standards laid down in US-FDA: 21CFR 175-300 and also having mechanical properties such as compressive strength 51 mpa (ASTM C 579), Flexural strength 12 mpa (ASTM C 580) & Tensile Strength 8 mpa (ASTM C 307) on floor as per approved colour and shade over Vacuum dewatered floor. The moisture content of the concrete flooring should be less than 5%.

Anti static membrane - Supply, installation, testing and commissioning double layer membrane each layer comprising heavy duty Serum based bituminous sheet and PVC sheet of thickness 1.20 and 0.40mm respectively (Two layers, each 1.60mm thick per layer) at platform edge, as per approved specification and drawing attached. Rate to be quoted by contractor shall be inclusive of materials like membranes and bituminous priming coat over concrete surface, labour, tools and tackles etc. complete by contractor. ( Including surface preparation and providing 9mm fire borad between vertical joint).

Acid and / or alkali resistant Vitrified floor tiles - Providing and fixing 10 mm thick acid and / or alkali resistant vitrified tiles of approved make and colour using acid and /or alkali resisting mortar bedding and joints filled with acid and / or alkali resisting cement as per IS:4457 complete as per the direction of Engineer-in- charge. On a flooring on a bed up to 30mm thick mortar of 1:4 proportion.The tiles shall be free from objectionable surface blemishes such as projections, depressions, flakes, hairline cracks and bubbles. The tiles shall be level and regular in size with properly formed corners and shall not be warped or deformed in any manner laid at right angles as per design and pattern if required.The flooring/Tiles shall be covered with POP / Gypsum powder of 12mm thick /Plywood to ensure that the flooring is not damaged till the construction work is completed and handed over.

Acid and or / alkali resistent Vitrified wall tiles - Providing and fixing 1st quality 10mm thick acid and or / alkali resistent Vitrified wall tiles of approved make,conforming to IS :4457, The tiles shall be free from objectionable surface blemishes such as projections, depressions, flakes, hairline cracks and bubbles. The tiles shall be level and regular in size with properly formed corners and shall not be warped or deformed in any manner laid at right angles as per design and pattern if required,shade, colour and finish in all colours, shades, size in skirting, wall cladding, border tiles and dados over 20/12 mm thick bed of cement Mortar 1:4 (1 cement : 4 coarse sand) and jointing with approved grouting material with pointing in white cement mixed with pigment of matching shade complete. The flooring/Tiles shall be covered with POP / Gypsum powder of 12mm thick /Plywood to ensure that the flooring is not damaged till the construction work is completed and handed over.

PAINTING WORK

Texture Paint - Providing and applying two coats of Texture paint by approved manufacturer after applying corresponding roller coat as primer on pre-plastered surface as per approved sample in approved shade. The composition of the texture paint should consist of ACRYLIC copolymer resigns combined with quartz ,silica, mineral, aggregates, synthetic inorganic pigments, bactericide, fungicides and various other additives, giving the product water repellant properties. The first coat to be applied by brush or wool roller as a base coat, diluted with sufficient water and the final coat (Undiluted) to be applied by trowel and finished with acrylic trowel to maintain with or without groves, as per details in drawings. The thickness of both coats should be 1.0 to 1.5mm. the water repellency of the product shall be >= 86gm/m2 as per test method IS:5410-1969, complete as per manufacture’s specifications and instructions by Engineer in Charge at site. The rate shall include necessary scaffolding, labour and material complete

External emulsion paint - Providing and applying two coats of exterior-grade acrylic emulsion base coat followed by two coats of premium weather-resistant exterior emulsion top coat with anti-fungal, water-repellent, and UV-resistant properties. Application shall include surface preparation, primer and finish coats. Complete in all respects. Minimum warranty for performance, anti-algal, anti-fungal and waterproofing of 10 years of approved brands.

Anti dust paint in shafts - Providing and Applying the Anti dust paint on RCC Surface (two or more coats) below the false floor with at all operational rooms/ locations after cleaning & preparing the surface i.e dust free and applying the said paint as per manufacturers specifiations including appropriate priming coat etc. complete in all respect and as per direction of Architect in charge.

ALUMINIUM WORK

ALUMINIUM LOUVER

Aluminium Louver - Providing, fabricating, testing (incl. performance analysis) and fixing sun louver system of max height 1500mm (fixing at all heights) and as manufactured by approved manufacturer. The system shall consist of Z-shaped panels fixed on aluminium extruded brackets. The panels shall be of dimension 98.5mm X 132mm with back rolled round edges and manufactured from 0.6mm thick aluminium alloy AA3005/3105/3003,coil coated with scratch resistant exterior grade paint finish. The anodised clamps belonging to the system shall be fixed to the approved substructure by others in 136.5mm c/c. All properties and specifications shall comply with ECCA directives and more specifically EN 1396:1996. Clamps shall be fixed to suitable substructure provided by others at 150 mm from panel edges and maximum centre-to-centre spacing of 1000mm. The panels shall be fixed to the clamps as per fixing procedures. The front side of the panel shall be of approved colours in exterior finish with 24-30microns thick and the backside shall have standard white polyester coating.

FIXED CUM OPENABLE WINDOWS

Aluminium windows for rooms, common areas and entry/exit - Providing, fabricating, testing (incl. structural analysis) and installing in position, pure polyester powder coated aluminium windows of max size 2400mm x 2400mm, of approved colour with an outer frame (Global Aluminium Section Code - 1609H, 1610H, 1832H, and 1832H or equivalent) and shutter (Global Aluminium Section Code - 1820, 1822, 1824 or equivalent ), glazing clip (Global Aluminium Clip Code - 1723 or equivalent) outer frames, architraves, beading, wool pile 8mm thick toughened glass, gaskets, complete including all fittings. The minimum sizes, thickness and weights per unit length of the aluminium sections to be given by tenderer, however, nothing extra shall be payable to the Contractor for using larger/heavier sections than those given, if found inadequate during structural analysis. For different sizes other than those mentioned, the unit rate will be calculated based on pro rata basis. Uniformity of thickeness of aluminium sections shall be ensured across different sizes of windows. The Aluminium frame shall have the strength and stability to withstand the load of the whole unit without any MS frame supports. No extra cost will be paid for MS frame supports. Solar reflectance index (SRI) of glass shall be greater than or equal to 75% or as per IGBC platinum rating.

Aluminium frames and windows for Platforms- Providing, fabricating, testing (incl. structural analysis) and installing in position, pure polyester powder coated aluminium windows of max height 2500mm and of approved colour with an outer frame (Global Aluminium Section Code - 1609H, 1610H, 1832H, and 1832H or equivalent) and shutter (Global Aluminium Section Code - 1820, 1822, 1824 or equivalent ), glazing clip (Global Aluminium Clip Code - 1723 or equivalent) outer frames, architraves, beading, wool pile 8mm thick toughened glass, gaskets, complete including all fittings. The minimum sizes, thickness and weights per unit length of the aluminium sections to be given by tenderer, however, nothing extra shall be payable to the Contractor for using larger/heavier sections than those given, if found inadequate during structural analysis. For different sizes other than those mentioned, the unit rate will be calculated based on pro rata basis. Uniformity of thickeness of aluminium sections shall be ensured across different sizes of windows. The Aluminium frame shall have the strength and stability to withstand the load of the whole unit without any MS frame supports. No extra cost will be paid for MS frame supports. Solar reflectance index (SRI) of glass shall be greater than or equal to 75% or as per IGBC platinum rating.

Aluminium windows for link bridge- Providing, fabricating, testing (incl. structural analysis) and installing in position, pure polyester powder coated aluminium windows of max height 2500mm and of approved colour with an outer frame (Global Aluminium Section Code - 1609H, 1610H, 1832H, and 1832H or equivalent) and shutter (Global Aluminium Section Code - 1820, 1822, 1824 or equivalent ), glazing clip (Global Aluminium Clip Code - 1723 or equivalent) outer frames, architraves, beading, wool pile, toughened laminated glass of 6mm + 1.52mm + 6mm, gaskets, complete including all fittings. The minimum sizes, thickness and weights per unit length of the aluminium sections to be given by tenderer, however, nothing extra shall be payable to the Contractor for using larger/heavier sections than those given, if found inadequate during structural analysis. For different sizes other than those mentioned, the unit rate will be calculated based on pro rata basis. Uniformity of thickeness of aluminium sections shall be ensured across different sizes of windows. The Aluminium frame shall have the strength and stability to withstand the load of the whole unit without any MS frame supports. No extra cost will be paid for MS frame supports. Necessary sliding windows as per drawing shall be provided at no extra cost. Solar reflectance index (SRI) of glass shall be greater than or equal to 75% or as per IGBC platinum rating.

ALUMINIUM DOORS

Note: If a new door size is required, the rate per sq.ft of the next higher standard size will be applied and this item will not be treated as an extra item.

Aluminium Door (1000mm X 2100mm)

Providing and fixing Aluminium Door with frame of approved make with door frame / chowkhat of section (Global Aluminium Section - 101.20 x 44.45mm S/G (1621) – Outerframe, 85 x 44.50mm Door vertical (1717), 47.50 x 44.50mm Door top (1706), 100 x 44.50mm Door bottom (1706), 18.4 x 17.10mm (1723) – Glazing Clips or equivalent) with bottom panel made of 12 mm thick prelaminated Novo pan or equivalent flat pressed three layered prelaminated particle board exterior grade ISI stamped IS: 12823 grade, type-II, one side decorative and other balancing white and edges sealed with water resistant paint. Top panel with 8 mm thick toughened laminated glass. Both board and glass will be fixed with glazing clips and beadings / gaskets and necessary fittings all as per manufacturer's specifications and directions. EPDM rubber gasket and frame fixed in position with steel screws and rawl plugs. All visible steel screws shall be rust resistant and coloured as approved.All aluminum sections shall be as per drawing and conforming to grade 63400 WP alloy as per IS:733 and IS: 1285 and colour 65 microns powder coated finish complete as approved and directed by the Engineered finish complete as approved and directed by the Engineer. The door to be complete with all necessary accessories such as aluminum handles, tower bolts, locks, pivot / hinges etc. complete.

Aluminium Double swing Door (2000mm X 2400mm)

Providing and fixing Aluminium Double swing Door with frame of approved make with door frame/ chowkhat of section (Global Aluminium Section - 101.20 x 44.45mm S/G (1621) – Outerframe, 85 x 44.50mm Door vertical (1717), 47.50 x 44.50mm Door top (1706), 100 x 44.50mm Door bottom (1706), 18.4 x 17.10mm (1723) – Glazing Clips or equivalent) with bottom panel made of 12 mm thick prelaminated Novo pan or equivalent flat pressed three layered prelaminated particle board exterior grade ISI stamped IS: 12823 grade, type-II, one side decorative and other balancing white and edges sealed with water resistant paint. Top panel with 8 mm thick toughened laminated glass. Both board and glass will be fixed with glazing clips and beadings / gaskets and necessary fittings all as per manufacturer's specifications and directions. EPDM rubber gasket and frame fixed in position with steel screws and rawl plugs. All visible steel screws shall be rust resistant and coloured as approved.

Cement Board panelling- Providing and fixing 8mm thick cement board panelling on a suitable aluminium framework using necessary screws, brackets, and accessories. Aluminium framework shall consist of vertical and horizontal members (minimum 1.2 mm thick, 25x25 mm or as specified), fixed to wall/partition at required spacing with stainless steel fasteners. Cement boards shall be fixed with countersunk screws at specified intervals ensuring a flush, level surface. Joints to be filled with suitable jointing compound and tape for a seamless finish. The entire system shall be installed plumb, true to line and level, as per manufacturer’s recommendations and site instructions.

Gypsum board partition - Supply and installation of 100mm thk FR single gypsum partition comprising of 12.5 mm FR gypsum board on both side with 72 mm GI tracks on top and bottom, 70 mm steel stud @ 600 mm c/c up to soffit height with 30 kg/m3 mineral wool insulation, complete with jointing, taping and ready to receive final paint. Height - 6m (soffit)

SUSPENDED CEILING WORKS

Perforated metal panel ceiling

Providing and installing suspended ceiling system at all levels with interlocking grid of size 1200x600mm / 600x600mm ceiling module consisting of demountable infill units (size 1200x600x0.5mm) having 50mm gap at every 1200mm, gap covered with 82mm wide channel having flanges to hold ceiling panels. The panels and channels shall be made from 0.5mm thick GI sheet, punched and bent to shape. The panels shall have perforated area 30-40%. The ceiling shall be powder coated (PPC, 80micron) on exposed and unexposed surface with approved colour. The grid system shall include hangers and runners of size 50x50x3mm thick hot dip galvanised steel, fixed on soffit of slab with the help of stainless steel expansion fasteners of size 10x75mm (Tam Anchor), The ceiling system to include panels, hanging system including the cost of providing opening and electrical fittings/fixtures, secondary supporting system for opening and below cable tray and duct, access to maintenance, all complete as per requirement of Engineer-in Charge.

Calcium silicate board ceiling

Providing and installing suspended ceiling systems/ vertical fascia as per controlled sample for concourse, 12mm thick Calcium Silicate Board panels with paint as per specification including supply of suspension system of galvanized steel as per manufacturer's recommendation, top fixing of SS expanding anchor bolts, rigid hangers, accessories inclusive of providing opening for electrical fixtures / fittings, fixed framing to support fixtures / fittings and providing secondary supporting system for cable tray and duct and all complete as per relevant drawings and the direction of Engineer- in- charge.

Baffle ceiling

Providing and fixing Baffle Aluminium panel ceiling manufactured by approved manufacturer of approved colour consisting of panel size 150 mm deep X 50 mm width using 0.7mm thick, Module of 150mm,panel length upto 5 mtr, Coil Coated on a Continuous Paint Line, Double baked and roll formed from enamelled corrosion resistance Aluminium alloy AA 3105 (Al. Mg) for higher strength and good roll forming characteristics. Panels shall be clipped to a baked enamelled Aluminium carrier of 30 mm wide x 47 mm high x 0.95 mm thick, Black Colour coated, one leg of the carriers with cut outs to hold the panels in a module of 300 mm. Panel carrier shall be suspended by means of M6 threaded rod at a pitch distance specified by the manufacturer standard. Aluminium panels shall be chromatised for maximum bond between metal and paint enamelled twice under high temperature, both sides with a full primer and finish coat on a Continuous Paint Line.

Polymer ceiling

Supply and fixing of Polymer ceiling system with appropriate panel sizes as given below. These panels can have hidden perforations/ Visible perforation/ Panel without perforation, ensuring a sleek appearance. Panel Specifications: Panel Sizes: 300mm x 3850mm, 300mm x 3050mm & 300mm x 2700mm Material: Polymer based material with thermal printing Characteristics: Durable, moisture-resistant, water-resistant, and resistant to borer-fungus-termite attacks. Installation Requirements: Panels to be installed using GI sections (0.55mm / 0.8mm thick) Gauge and size of sections : 1. Perimeter channel for Fixing J trim 1.5” parameter 2. Furring Channel for Fixing Soffit. Fixed perpendicular to soffit panels every 450mm 3. Main Channel for Beam support. Fixed every 1000mm 4. Wall angle / channel for frame weight bearing Fixed ceiling to frame every 1000mm 5. Self Tapping screw - Philip pan head screw – 1” for GI channels Accessories: Profile with dimensions 40x19x22x12x3050 (all in mm) for edge profiles Profile with dimensions 67x3050 mm with T head of 42mm for Connecting profiles Maintenance and Durability: Panels must be maintenance-free and rust-proof. 100% water-proof properties to be ensured. Minimum 10 years warranty for colour & finish of the panels and the profiles.

METAL WORK

SS Railing for Main Staircase- Supplying, fabricating, MATTE FINISH, errection of 1100mm high SS hand railing as per design comprising of 50mm dia, 2mm thick, Stainless steel Grade 304 with balustrades as per drawing, SS base plate, pipe adjuster M16X200mm SS fasteners for fixing railing in floor by cutting hole of required dia in floors/ landing/staircase complete in all respect and making good the floors as per Specifications and Architectural Drawings.Weight of finished product shall be measured. Rate is inclusive of all wastages. Adjustment for opening or cuttings is not allowed. This includes 4mm thick SS metal plate with CNC cutting as per approved design in all landings. (Calculated as 20Kg/Rm)

Grab Bar on walls- Supplying, fabricating, MATTE FINISH, errection of SS Grab Bar as per design comprising of 19mm dia, 3.15mm thick, Stainless steel Grade 304 with balustrades as per drawing, SS base plate, pipe adjuster M16X200mm SS fasteners for fixing grab railing in Wall by cutting hole of required dia in toilet complete in all respect and making good the Wall as per Specifications and Architectural Drawings. Weight of finished product shall be measured. Rate is inclusive of all wastages. Adjustment for opening or cuttings is not allowed. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.) (Calculated as 10Kg/Rm)

Platform edge SS railing- (Supplying, fabricating, MATTE FINISH, errection of required height 1500 mm high SS hand railing system, System comprising of 50mm Dia & 1.6mm thick Top-Rail Stainless steel Grade 304 connected to 50 mm Dia 3.15mm thick Baluster through Stainless Steel Saddle Plate connector. And a Grab Rail of 50mm Dia connected to Baluster through a Stainless Steel Stem Key. Baluster fixed to slab with GI Baseplate & M16x200 mm Fastener. A SS cover plate would be provided above GI Base Plate. Provision for advertisement with openable Aluminium kitchen shutter/ openable profile framework, 4mm aluminium sheet welded onto profile, 2mm foam board over metal sheet for vinyl pasting, 3mm clear polycarbonate sheet over foam board to protect vinyl graphics, SS studs of appropriate size L hexa key type are also included in the item. (for payment purpose, only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.) (Calculated as 18.5Kg/Rm)

Metal frame supports- Providing and fixing M.S. tube of approved size by welding etc. for substructure for panels, screens etc. including applying a priming coat of approved steel primer fixed with dash fastener complete.

Aluminium frame supports- Providing and fixing aluminium mill finish sub frame work with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS: 1285 fixed with rawl plugs and stainless steel screws etc.

Entrance Grill Gate -Providing and Fixing Foldable M.S.Grill Gate as per architectural detail drawings.The rate is inclusing of epoxy three coat Painting over primer with approved shades and all other hardware fixtures including hinges, Rollers etc for installation complete as per technical specification and Engineers direction. This includes 2mm thick SS metal plate with CNC cutting (approximately covering 25% of the total unit area) as per approved design.

MS Railing -Providing and fixing M.S. steel hand railing as per the design and drawings and specifications to staircase approximately 1200 mm high comprising of 32 mm dia 10 Gauge MS hollow tube vertically fixed to every fourth step welded to 50 mm dia 10 gauge MS pipe on top for handrail and 20 mm dia MS pipe vertically in between welded to 2 Nos of 20 mm dia M.S. Pipe all as per the drawings, the vertical balusters are fixed in position with molten lead poured into 40 mm dia GI sleeve with 80 x 80 x 3mm GI Plate and embedded in RCC including necessary steel cover and completed as shown in the drawings or any other method of fixing as approved by the Architect in charge like epoxy grout fixing etc., complete. All M.S. members will be painted with three coats of synthetic epoxy of approved make and colour over one coat of primer all as per manufacturer's instructions and with the engineer's approval. (Calculated as 20Kg/Rm)

MS Canopy, fencing etc- Providing and fixing MS fencing,Trellis and MS Conopies, all as per details as per specifications inclusive of all fabrication,painting ( 1 coat of primer and 2 coats of epoxy paint ) as required as per the direction of Architect-in-charge.

Chicken wire mesh -Providing approved galvanized chicken wire mesh (24 gauge 12mm size) to junctions of concrete and masonry work and other locations where called for including cutting to required sizes side laps of minimum 75mm and fixing in position with galvanized wire nails as approved.

Steel Framework - Providing and fixing structural steel frame work for paneling works, other framing works, reinforcing external facade at all heights using M.S. square/ rectangular tube including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of M.S. brackets/ flats etc. which shall be welded to the frame and anchored in wall. The steel work will be given a priming coat of Zinc primer.

PVD Coating - Providing 0.06 Micron PVD coating on SS material as per requirement. Minimum 8 years warranty for PVD coating defects.

DOORS & ROLLING SHUTTER WORKS

Note: If a new door size is required, the rate per sq.ft of the next higher standard size will be applied and this item will not be treated as an extra item.

120 Mins. Fire rated hollow metal doors - Painted Providing and fixing of Hollow metal fire rated doors as per IS 3614 part-1 & part-2 for stability and integrity. Pressed Galvanized steel confirming to IS 277 with the following specification. Recommended fire door shall have doors tested at CBRI or ARAI for maximum rating of 2hrs with vision panel. Test certificates should be available for vision lites /panels as part of the fire door assembly. Independent glass test certificates will not be accepted. Manufacturer test certificate shall cover doors both single and double leaf and all doors supplied should be within the tested specimen, deviation in specification and sheet thickness other than what is mentioned in the test certificates are not allowed. Proper label confirming the type of door and the hourly rating is mandatory. Approved manufacturer Shakti Hormann or approved equivalent.Door frame shall be Single rebate frame profile of size 125 x 60mm made out of 1.60mm (16gauge) minimum thick galvanized steel sheet.

1500x2400 - 120Mins Fire Rated Door Double leaf with vision panel (150mm x250mm)/ circular (dia 300mm) with hardware set, iron mongeries ( dorma,geze or equivalent) and locks.

1200x2100 - 120Mins Fire Rated Door Double leaf with vision panel (150mm x250mm)/ circular (dia 300mm) with hardware set, iron mongeries ( dorma,geze or equivalent) and locks.

750x2100 - 120Mins Fire Rated Door Single leaf with hardware set, iron mongeries (dorma,geze or equivalent) and locks.

1800x2400 - 120Mins Fire Rated Door Double leaf with vision panel (150mm x250mm)/ circular (dia 300mm) with hardware set, iron mongeries ( dorma,geze or equivalent) and locks.

750x2000 - 120Mins Fire Rated Door Single leaf with hardware set, iron mongeries (dorma,geze or equivalent) and locks.

Metal Door - Providing and fixing door with shutter fabricated from 18 gauge thick galvanised steel sheets press formed to provide a 46mm thick fully flushed double skin door with lock seam joints at stile edge and infill insulation Kraft core. Door frames 57x120 mm approx. to be single rebated made of 16 gauge galvanised steel. Door shutter and frame to be primed in stoving grade epoxy zinc phosphate primer and finished in aliphatic grade u.v. resistance polyurethane paint. Door shutter and frames to have all hardware preparations including the installation of ironmongeries and locking system, prepunctured at the factory. all complete with and including filling of door frames with P.C.C. 1:5:10 (1 cement: 5 aggregate : 10 coarse sand).

1050x2100 - Single leaf door shutter with air transfer grill with hardware set, iron mongeries ( dorma, geze or equivalent) and locks.

750x2000 - Single leaf door shutter with hardware set, iron mongeries ( dorma,geze or equivalent) and locks.

900x2100 - Single leaf door shutter with hardware set, iron mongeries ( dorma,geze or equivalent) and locks.

1050x2100 - Single leaf door shutter with hardware set, iron mongeries ( dorma,geze or equivalent) and locks

1000x2100 - Single leaf door shutter with Vision panel (150mm x250mm)/ circular (dia 300mm) with hardware set, iron mongeries ( dorma,geze or equivalent) and locks

1000x2100 - Single leaf door shutter with air transfer grill with hardware set, iron mongeries ( dorma, geze or equivalent) and locks

2000x2100 - Double leaf door shutter

Rolling Shutters -Supplying and fixing automatic galvanized industrial motorized rolling shutters made of required size MS lathe interlocked together (heavy duty) of approved make made of required sizes and shape with G.l guides control box drive unit and with all other accessories complete as per manufacturer's specifications.

3400x4000 - Shutter with hardware set, iron mongeries etc.

3000x3000 - Shutter with hardware set, iron mongeries etc.

3000x3000 - Shutter with hardware set, iron mongeries etc. with perforation

1800x3000 - Shutter with hardware set, iron mongeries etc. with perforation

GLASS WORK

Glazing for EFO, SCR, TOM and security room - Providing and installing fixed glazed security wall assembly of stainless steel to ticket offices, Station Control Room, etc. with specified fixings and finish using 2 sheets of 6mm thick toughened glass with nominal gap silicone sealant joints. Glass shall be clear, toughened and laminated with 1.52mm thick polyvinyl butyral layer- all complete as per relevant architectural drawings and specification with cut out & holes.

Laminated Glass Door - Providing and fixing of toughened laminated glass door (dorma,geze or equivalent 6mm + 1.52mm + 6mm) including stainless steel door handles, deadlock and Floor spring complete, necessary cutting in granite flooring for housing of floor spring as per drawing

Toilet Mirror -Providing and fixing toilet mirror in 6 mm thick clear float glass with beveled and polished at edge, fixed on wall with 6mm thick hard board backing fixed to wooden cleats with 8mm dia 38mm long stainless steel stud complete (Circular with dia 600mm)

Glass Partition wall for PD - Supply and Installation of Full Height Toughened glass partition with 45mm x 25mm with minimum 1.5mm thickness Polished Aluminium partition systems using snap on option for installing 10mm Toughened glass from FFL to max 2600 mm.

Framed Glass Partition b/w Paid & Unpaid area in the concourse - Providing and fixing in position framed glass partition walls of maximum height 1.8m and made out of 12mm thick toughened laminated clear float glass held in position by wall connecting profile as per architecture drawing by Stainless steel frames (SS-304) of suitable size to make it free standing including all fixtures.

Glass canopy - Providing and fixing canopy over entrance using 2 sheets of 6mm thick toughened glass with nominal gap silicon sealant joint. Glass shall be clear, toughened and laminated with 1.52mm thick polyvinyl butyral layer, with spider fitting as per specification and inclusive of providing and fixing frame of SS grade 304 dia pipe pulled up with tension and fixed to the wall. Including gutter as per architecture drawing.

Curtain wall Glazing - Providing and fixing at site curtain wall Glazing for all heights and all levels, using powder coated Aluminium section of approved make - 55 mm x 104mm x 2 mm section, Weight 1.819 kg/m with Fixing Pressure Plate of approved make, 53.45 mm x 9.5 mm section, Weight 0.515 kg/m also with Fixing Cap, 55 mm x 15mm x 1.5 mm section, Weight 0.342 kg/m with L angle 25x75x3mm, Which conform to wind load and static load, form into grids depending on the site measurements and securely fixing the frame work in to the existing structural steel work using 50X75X 6mm thick galvanized steel angle welded to the structure. adequate and properly designed frame work finished to line and level. 8mm clear toughened Glass shall be fixed to the frame work and supported with pressure plates and cover caps. The Aluminium section shall be properly powder coated to 50-60 microns as per approved color. Cost shall include cost of all materials, testing, transportation & labour charges and necessary scaffolding as per the details below; a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including , sleeves and splice plates etc. screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard. b) Fabricating and supplying serrated M.S. hot dip galvanised brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing curatin wall glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using GI anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of GI , of the required capacity and in required numbers. Note: a) For the purpose of payment, only the actual area of structural glazing (including width of frames) on the external face shall be measured in sqm. up to two decimal places.

Toughening of glass - Extra for ( float glass panes of 8 mm thickness (weight not less than 20 kg/ sqm) toughening

WATERPROOFING WORK

Terrace Waterproofing

Waterproofing System: Hybrid Poly Urea Water proofing - Providing & Applying approved two components, solvent free, spray applied hybrid Poly urea Waterproofing membrane on the clean and sound concrete base for the application including surface preparation by mechanical grinding, treatment of cracks, bore packing, coving etc as per manufacturer specification. Followed by laying of geotextile membrane.

EXTERNAL ARCHITECTURAL FINISHING WORKS

Canopy for DG Room/ Pump room entrance

Polycarbonate Sheet Supply and Installation of translucentpolycarbonate roof with multicell polycarbonate panel system. The system with complete assembly of co extruded UV protected multicell panels incorporated into a complete system. Co-extruded UV protected polycarbonate panel system of min 16 mm thick of 900mm-1200mm width with angular daylighting concept. Panel shall be fixed over MS structural steel/MS purlin (paid separately) conforming to the detail technical specifications as per approved architectural drawings. Trained and factory authorized labour with supervision to complete the entire panel installation as per drawing & direction of the engineering in charge.

Aluminium composite Panel - Providing and fixing Aluminum Composite panels in all colours of approved brand for wall cladding at all heights and elevations including necessary aluminum composite panel consist of 3mm thermoplastic core of anti oxidant LDPE sandwiched between two skin of 0.5 mm thick alloy sheet making a total sheet thickness of 4 mm. The surface shall be finished with PVDF base coating on the top side and service coating on the reverse side shall be with a polymer paint. Coating shall confirm to ECCA of AAMA. The system shall design to withstand wind pressure of 200 Kg/Sqm and shall be fixed to the masonry/RCC walls with necessary clamps, bracket and anchor fasteners. All Clamps and brackets shall be hot dip galvanized minimum 80 micron thick and confirmed to IS : 4759 - 1996. The extruded aluminum sections shall be anodized in approved colour with anodic coating minimum 20 microns. Extruded section shall be of 6063 T5 or T6 alloy confirming to ASTM B 221. (items include cost of aluminum frame, ACP Panels, Cramps 110mm size, weather sealant, gasket, foam, fixtures, scaffolding, all machineries and any other fastening strips, nuts, bolts, rivets, washers, etc. complete).Item shall include to provide EPDM gaskets ( by approved manufacturer), open cell polyethylene backer rods, weather sealant etc. The weather sealant shall be Dow Corning 991 or equivalent and the width of the gap filled with sealant shall be as specified. The rate inclusive cost for profiling and designing as per detail design drawing. This includes any doors in the ACP cladding for accessing the service ducts with its accessories and locking system.

Truss less Arch roofing - Supply, erection and installation of truss less arch roofing with rainwater gutters of size 30cm x 30cm as per the technical specification and colour as approved by Architec-in-charge.

Standing seam roofing system - Providing, fixing Aluminium standing seam roofing system, bending to required curved profile and fixing single skin Klip lock concealed system Profiled Sheeting 500-770 mm cover width, 43 mm crests @ 186-333 mm c/c manufactured out 0.50mm BMT (base metal thickness) Hi-tensile color coated Zincalume/Galvalume steel. The sheets shall have wide pans with stiffening ribs for effective water shedding & strength. Special male/female ends with full return legs on side laps for Purlin supports and anti-capillary flute in side lap. The sheets shall have hot-dipped metallic Zinc-Aluminium alloy coating (150 gms / sqm, Zinc 45%, Aluminium 55%). Coating mass total on both sides AZ-150 or equivalent as per AS 1397-1993 Minimum 550 Mpa yield strength with Super durable Polyester XRW/ SMP quality paint coat of approved colour. Coating shall be as per AS/NZS-2728-1997, Category 3-4 Total coating thickness of 35 microns, comprising of 20 microns exterior coat of Super Durable Polyester XRW/SMP on top surface and 5 micron polyester reverse on back surface over 5 micron primer coats on both surfaces including side and end laps. The Sheets shall be fixed using approved continious clip KL-70 or equivalent manufactured from Hi-tensile Zincalume / Galvalume steel base and galvanised hooks as approved by Engineer - In- Charge, The clip shall be fastened by polymer coated hot dip galvanized hex head self drilling fasteners as per AS 3566 class 3 with EPDM washers on each crest of sheets for connection with Purlins and polymer coated hot dipped stitching fasteners @ regular Interval on all sides and end laps.

Providing and installation of aluminium roofing sheet/ plane aluminium flashing sheet (16 inches width) of 0.5 mm thickness for canopy works.

MISCELLENEOUS FINISHING WORKS

Expansion joint treatment

Providing & Fixing expansion joint treatment with silicon sealent and baker rod for a joint width of 50mm flat expansion joint and provide 2 layers of flexbile sheet or expansion joint complete as directed by Architect-in-charge.

Providing & Fixing Joint/gap treatment with polysulphide sealent and baker rod for a joint width upto 25mm flat expansion joint complete as directed by Architect-in-charge

Toilet Cubicle- Providing & fixing Toilet Cubicle (of following standard dimension which includes 600mm door size width) made of heat, bacteria, water,chemical,scratch and impact resistant 12mm thick solid compact laminate panels tested in approved laboratory. Finish of the compact laminate should be Suede, Raw silk model includes doors, pilasters & intermediate panels finished with approved texture/shade as per the approved detail drawings & as per IS 2046 (Indian standard) and as per fire retardant BS-476/97 standard. This also includes providing and fixing in position necessary hardware made out of stainless steel (Grade 304) as per manufacturers specifications & Architects instructions like (1)Door knob(2)Gravity hinges(3)Thumb turn lockset with occupancy indicators(4)Coat hooks with Door stopper(5)U- channels(6)Adjustable foot/pedestal(7)Top rail with corner connector(8) Rubber noise deafening tape(9)Screws & wall plugs. All screws will of 304 Grade in stainless steel with satin finish. All pilasters are supported by stainless steel bottom cladding. The base of the stainless steel bottom cladding will be anchored to the floor with a clearance height up to 100mm. the top fitting should consist of SS round top rail which will get fixed with pilasters, with SS panel tube holder, SS corner bend (connected with top rail) will be used on the corner of cubicle in absence of brick wall, SS wall fixing is used only on the wall which will hold the SS top rail.

Toilet Cubicle with standard dimension of 1980mm Height x 1250mm Width x 1520mm Depth, which includes 600mm door size width.

SS sheet cladding on sides of Escalator for closure of gaps - The outer decking extensions for escalators shall be done using 1.5mm thick stainless-steel sheets of SS304 grade Panels shall be with reinforcement and sprayed – on fire resistant vibration / sound attenuating backing material and decking extensions shall have tight butt joint and be fastened to the truss with concealed stainless-steel bolts, nuts and washers. The joint line shall be perpendicular to the escalator step nose line without any longitudinal joints. All joint lines of decking extension shall be aligned and staggered in arrangement in line with the joint line of interior panel. Additional supports for decking extension are to be provided with Gi angles and chequered plates appropriately. The architectural contractor shall interface with escalator contractor for installation as a part of his interface responsibilities. This includes supporting MS frames if needed.

Interlocking Paver Block 60mm - Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with fine sand etc. all complete as per the direction of Architect-in-charge.

Interlocking Paver Block 100mm - Providing and laying 100mm thick factory made cement concrete interlocking paver block of M -40 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with fine sand etc. all complete as per the direction of Architect-in-charge.

FRP Manhole cover -Providing and fixing in position FRP manhole cover & Frame 25MT capacity including fixing of manhole frame to the drain cover slab as directed by the Engineer in charge

FRP manhole cover of size 450x450mm internal

FRP manhole cover of size 600x600mm internal

Epoxy flooring - Supply and application of 3mm thick Epoxy Flooring on areas applied as per manufacturer's recommendation with one priming coat of 150 microns followed by a screed coat of 2mm thick and finishing off with a top coat of 1mm thick Location: ASS, TSS

Wooden Architrave at Lift entrance - Providing, fabrication and fixing wooden architrave at Lift entrance door as with 1 mm thick Mernino make laminate panels lined on top of 12mm thick BWP ply with necessary hardwares, ply shall be fixed to a frame work consisting of 25mm x 50mm x 1.5 mm aluminium tube section at 600 c/c or as required. The cost to be includes all materials, labour,wastages, lead, lifts, necessary staging/scaffolding. cutting, necessary hardware, protections, tools and machinery, all other related works, all complete as per drawings, specifications and to the approval of the Architect in charge.

Polymer Wall cladding: Supply and fixing of Polymer Facade system with panel sizes of 250mmx 2950mm. Panel Specifications: Panel Sizes: 250mm x 2950mm Material: Polymer based material with thermal printing Characteristics: Durable, moisture-resistant, water-resistant, and resistant to borer-fungus-termite attacks. Installation Requirements: Panels to be installed using Aluminium sections (1mm thick) 1. 50 x 25 x 1mm – vertical framing 2. 38 x 38 x 1mm – horizontal framing 3. Self drill screw for L clamp and AL channels 4. Anchor fasteners to fix aluminium channel on wall 6-8 thick 5. Truss flat head screw – panels and trims 8mm dia, 25mm length Accessories: Profile with dimensions 40x19x22x12x3050 (all in mm) for edge profiles Profile with dimensions 76x3050 mm with T head of 42mm for Connecting profiles Profile with dimensions 46x3050mm starter trim Profile with dimensions 40x44x3050mm ventilation trim Profile wih dimensions 76x76x3050mm exterior trim Profile with dimensions 31x3050mm interior trim Maintenance and Durability: Panels must be maintenance-free and rust-proof. 100% water-proof Minimum 10 years warranty for colour & finish of the panels and the profiles.

Description of Work / Item(s)

Amount

CONCRETE WORK

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge

All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) (for screeding)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:

1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/recoverable separately).

All works above plinth level upto floor V level Note:- Excess/less cement over the specified cement content used is payable /recoverable separately.

Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable /recoverable separately.

Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum)

Centering and shuttering including strutting, propping etc. and removal of form for

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more

GRANITE WORK

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red

Area of slab over 0.50 sqm

Extra for fixing marble / granite stone over and above coresponding basic item, in facia and drops of width upto 150 mm with expoxy resin based (Araldite or equivalent) adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

FLOORING WORK

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.

18 mm thick

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar matching pigments etc., complete on floor and skirting

Size of Tile 600x600 mm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc.complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

STEEL WORK

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required

In stringers, treads, landings etc. of stair cases including use of chequered plate wherever required, all complete.

In gratings, frames, guard bar, ladder, railings, brackets, gates, cable tray supports below u girder and similar works

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.

M.S. tube.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.

Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade

FINISHING WORK

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

1:6 (1 cement: 6 fine sand)

15mm cement plaster on the rough side of single or half brick wall of mix

1:4 (1 cement : 4 fine sand)

1:6 (1 cement : 6 fine sand)

20 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

20 mm cement plaster of mix :

1:4 (1 cement: 4 coarse sand)

6 mm cement plaster of mix :

1:3 (1 cement : 3 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :

New work (two or more coats) over and including water thinnable priming coat with cement primer

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Finishing walls with water proofing cement paint of required shade :

New work (Two or more coats applied @ 3.84 kg/10 sqm).

Applying priming coat:

With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

On concrete work (on wall)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

WOOD & PVC WORK

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.Should be water proof in case of Toilets and dining area

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

ALUMINIUM WORK

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately).

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

EXTERNAL DEVELOPMENT WORK

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Precasting and placing in position 125 mm dia Bollards 600 mm high of required shape including providing M.S. Pipe Sleeve 50 mm dia 300 mm long in the Bollard and M.S. Pipes 40 mm dia and 450mm long with 150x150x6mm M.S. plate welded at bottom and embedded 150mm in cement concrete 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size), including necessary excavation of size 250x250x450mm deep for the same in bitumen/ concrete pavement at specified spacing.

Description of Work / Item(s)

Amount

SANITARY FIXTURES

Health faucet - Providing & fixing Health faucet with 1.2 metre long Flexible Tube connected with two way bib cocck and CP wall hook with PVC & SS Screws including cutting and making good the wall wherever required complete as directed by the Engineer-in-charge (IGBC Compliant 1.5 LPM at design water pressure 3 bar). Make: Jaquar/Kohler/Hindware or equivalent

Grab bar - Providing and installation of grab bar set including hinged rail 750x100mm ,Corner grab bar 500x600mm M,Wall mounted grab bar 350mm ,Wall mounted Grab bar 600x40mm

Providing and fixing SS Waste Coupling 32mm model no. FT/HT, Make CHILLY complete in all respects and as per direction of Engineer-in charge

Wash hand basin- Supply and fixing of best Indian make white vitreous chinaware wash hand basin mounted on cantilever supports fixed to wall including making all connections, necessary fitting, screws and cutting and making good to wall and floor wherever required all complete as per direction of engineer - in -charge, comprising of counter top oval wash basin size 550 mm x 430 mm x 195 mm

CP Brass Auto Closing Pillar/Mixer tap

Supply and fixing of CP Brass Auto Closing Pillar/Mixer tap for best Indian make white vitreous chinaware wash hand basin as per direction of Engineer - in - Charge.

Urinal - Providing and Fixing glazed vitreous china wall hung lipped type half stall urinal size 245x300 mm with pressmatic, C.I. hangers, 15mm dia inlet to built in spreaders with inbuilt waste with 32mm diameter CP domical waste with dome grating C.P flange, complete including cutting and making good the walls and floors wherever required complete in all respects as per direction of the engineer-in-charge.

Water cooler - Providing in position storage type Water Cooler of the following capacity, ISI marked, stainless steel front panel, CP brass push cock, inlet float valve, with all plumbing and electrical accessories, inlet, outlet,overflow and drain out connection to floor drain complete as required.

Cooling capacity 40 litres/hr. and storage capacity 80 ltrs.

Providing, Fabricating and fixing of Flat type filter 10-20 micron, G4 media in middle and seperated with HDPE Mesh Flatly stitced on both side using aluminum frame work including neccessary Supports for fixing filter as complete as directed by engineer

Mop sink - Providing and fixing of mop sink with its fittings, including painting of fittings and brackets of four side covering Size 60X60X45 cms (Sink Size:- 45X40X25 cms)

Providing and Fixing concealed stop cock with wall flange (20mm)of approved quality

20 mm nominal bore

Wash basin - Supply and Installation of half pedestal wash basin for DA toilet

Food waste crusher - Providing & fixing of Food Waste Crusher fitting with Sink inclusive all accessories & fittings

Mirror - Supply and Installation of Mirror with aluinium beading all around and shall be approved make of size of 600 x650 x 5.5mm thick and fixed to the wall on wooden blocks with CP brass screws and CP washers.All complete

SOIL, WASTE & VENT PIPES AND FITTINGS

Providing, fixing, testing and commissioning of UV stabilized UPVC SWR pipe type 'B' conforms to IS : 13592 including all fittings such as bends, tees, elbow, 'Y', offset, cleaning pipe door, clamps, cowl etc. conforming to IS: 14735 and steel structural supports etc. including cutting the floors, walls and making good the same in cement concrete 1:2:4 & cement mortar 1:4. The wall thickness of pipe and technical characteristic conforms to IS : 13592-1992 type 'B'. The fitting dimension conforming to IS : 14735-1999. The jointing to be completed with rubber ring joint/ solvent weld joint as required/ applicable. (For Soil and Waste)

110mm dia.

Providing, fixing, testing and commissioning of UV stabilized UPVC SWR pipe type 'A' conforms to IS : 13592-1992 with all fittings such as bends, tees, elbow, 'Y', offset, cleaning pipe door, clamps, cowl etc. conforming to IS: 14735 and steel structural supports etc. including cutting the floors, walls and making good the same in cement concrete 1:2:4 & cement mortar 1:4. The wall thickness of pipe and technical characteristic conforms to IS : 13592 type 'B'. The fitting dimension conforming to IS : 14735-1999. The jointing to be completed with rubber ring joint/ solvent weld joint as required/ applicable. (For Rain Water)

110 mm dia.

160 mm dia.

200 mm dia.

Providing, fixing, testing and commissioning of UPVC waste Pipe conforming to IS: 4985-2000 class III (6 Kg/Sq.cm) including all moulding fittings conforming to IS: 7834-1987 such as tees, bends, reducers, coupling, adopters etc. solvent welded joint as per manufacturer recommendation including cutting and making good the walls, floors, R.C.C. work etc. (For fixtures waste).

40 mm dia.

50 mm dia.

63 mm dia.

Providing, fixing, testing and commissioning of UPVC 'P' trap/floor trap/urinal trap of self cleansing design having 50 mm water seal with or without horn conforming to IS: 14735-1999 including setting with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 hard stone ballast 20 mm nominal size) including cost of cutting and making good the walls & floors wherever required.

110 mm inlet and 110 mm outlet

Providing and fixing Heavy Class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waste and FT.

Size 100 mm X 100 mm

Providing and fixing UPVC floor drain including all fitting and accessories fixed in cement mortar complete in all respect.

110 mm OD x 63 mm OD

Providing, fixing, testing and commissioning of UPVC cleanout plug conforming to IS : 14735-1999 complete with all fitting; accessories and civil work.

110 mm outer dia.

Providing, fixing, testing and commissioning of UPVC waste Pipe conforming to IS: 4985-2000 class III (6 Kg/Sq.cm) including all moulding fittings conforming to IS: 7834-1987 such as tees, bends, reducers, coupling, adopters etc. solvent welded joint as per manufacturer recommendation including cutting and making good the walls, floors, R.C.C. work etc. (DRAIN PIPES).

50 mm dia.

75 mm dia

Supply and Fixing of Floor Clean Out with suitable accessories & fittings for opening in SS cap as required complete in all respects. All complete

110 mm dia

WATER SUPPLY

Providing and fixing G.I. pipes complete with G.I. fittings and clamps including cutting and making good the walls etc.(For OHT Riser)

65 mm dia nominal bore

80 mm dia nominal bore

Providing and fixing of 100 mm GI elbow

Providing and fixing of 100 mm GI Flange

Providing and fixing 100mm GI Nipple

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge

65 mm dia nominal bore

Supply, Installation, Testing and Commissioning of Butterfly Valves flanged end of the following sizes (conforming to IS: 13095), suitable for pressure rating of 10 Kg / Sq. cm, with Cast iron body, cast iron gear unit, flag, and Wafer type conforming to IS: 210, all materials of valve shall comply with the specification, including painting complete as required.

80mm dia.

100mm dia.

Providing and fixing forged brass ball valve (Screwed) of brass body conforming to IS 292 LCB 1 with hard chrome plated steel ball inside PTFE (Teflon) seat & ring with chrome plated centre handle with female BSP threads complete in all respects.

40mm dia

50 mm dia.

65 mm dia

80 mm dia

Providing and fixing in position Float Valve with Stainless Steel Ball Float and Stainless Steel Rod of required length conforming to IS 6603, suitable for pressure of 10 kg / Sq.cm. as per specification.

80mm dia nominal bore

Providing and fixing Pressure Gauge (suitable for working pressure of 0 - 16 kg / cm2) of stainless steel with 150mm phenolic dial (white dial with black numerals), SS 316 bourdon tube, nylon movements and micrometer type adjustable aluminium pointer with accuracy of ± 0.1% of span including accessories like suitable size of gauge cock, snubbers for pump discharge applications and name plate, etc. It shall be weather proof with an IP 65 enclosure, as per specification.

Providing all materials and labour for supplying and fixing multi-level indicator cum controller, operating in electronic sensing probe and having the controller equipped with level monitoring system and phase monitoring system for automatic operations of various pumps and indicating water levels for various tanks and having multi-level 4 nos. Visual indications on panel with alarm system and timer including necessary cable and acknowledge facilities as per requirement and all complete as approved.

Providing and fixing Level switches for OHT (high level and low level), Probing sensor as per Tank height

Providing and fixing Level switches for Under Ground water tank (high level and low level), Probing sensor as per Tank height

Providing and fixing Cast Iron (Conforming to IS 210) Y strainer (Flanged) PN 16 as per specification

65 mm dia

80 mm dia

Providing, fixing, testing & commissioning of 100 mm dia. tanker inlet connection complete with GI heavy duty inlet piping, hose inlet connection, MS cabinet enclosure (epoxy painted after fabrication).

PUMPS

Water Trasfer Pump ( 1 Working +1 Stand By)

Supply and installation of Vertical Inline multistage centrifugal type water supply transfer pumps (1 duty + 1 standby) including foot valves, strainers, non return valves, gate valves, pipe headers, brackets, suction piping, test line, float switches control panel, plinths, with all the safety devices such as MCCBs, ELCBS, dry run protection, automatic pump change over operation, phase failure relays, overload protection etc. related wiring and all the other accessories required to complete the job.

Domestic Water transfer pump (Station), Capacity- 150 Litre/Minute, Head- 40 Meter

Domestic Water transfer pump (Station), Capacity- 130 Litre/Minute, Head- 40 Meter

Domestic Water transfer pump (Station), Capacity- 135 Litre/Minute, Head- 40 Meter

Domestic Water transfer pump (PD), Capacity- 50 Litre/Minute, Head- 40 Meter

Booster Pump ( 1 Working +1 Stand By)

Supplying and installation of Vertical Inline multistage centrifugal booster pump set (One no's Duty & one no's standby) including VSD for each for transferring water from water sump to the Fixtures as shown, including pressure vessel as appropriate, pump mounted on steel base frame, foot valves with strainers on suction lines, all valves as specified on both delivery & suction line. Pump controls shall be for automatic operation with auto change over and manual override for sequential operation between the two pumps and on/off switches with electrodes or "pear" type float controls in sump as per specification. Rate shall also include for all fittings, specials, supports, brackets, anchors etc. and pressure gauges. Pump control panel shall have all the protective devices such as MCCBS, ELCBS phase failure relay, overload relay, dry run protection etc. & accessories, all as specified & shown on drawing

Capacity-35 Litre/Minute, Head- 35 Meter

Submersible drainage pump - Providing, fixing and commissioning non clog type mono block submersible drainage pumps suitable for handling solids of 40 mm size with totally water and dust proof motor as specified complete with motor control panel and float switch, chain and guide rail inclusive of all terminations and earthing required all complete as per specifications.

Capacity 120 lpm & Head 15 m (1W+1S) (Location : Pump room )

TUBE WELL

Boring in all soils except ordinary hard rock which requires blasting , with 110 mm diameter perforated casing pipe in for all hand pump / tube well etc including all testings as per Engineer

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC 100mm dia( 6kg/cm2) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer –in-charge

Supply and installation of 1HP submersible pump including all accessories etc complete

BIO-DIGESTORS SEPTIC TANK

Manufacturing,Supply & Installation Testing and Commisioning of special filter media, bio-culture media, Bio additives with necessary Equipements for proper functioning of the System including Lab Test Report for Treated Water including pipe line fittings in bio digestor.(Civil Work Excluded). Rate to include oil and grease seperator.

Capacity of 10 cu.m

Capacity of 16 cu.m

Capacity of 17 cu.m

Capacity of 27 cu.m

Description of Work / Item(s)

Amount

SANITARY INSTALLATIONS

Liquid Soap Container (Soap Dispenser)

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Bib Cock

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 inclusive all fittings & accessories

15 mm nominal bore

20 mm nominal bore

Kitchen sink - Providing and fixing stainless steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required.

Kitchen sink with drain board 510 x1040 mm bowl depth 200 mm.

Water Closet (European Type)

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings andbrackets, cutting and making good the walls and floors(approved brands Jaguar,Hindware or equivalent)

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing C.P brass angle valve for basin mixer and geyser points of approved quality confirming to IS:8931

15 mm nominal bore

Providing & fixing unplasticised PVC connection pipe with brass unions, 30cm Length

15 mm nominal bore

Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

15 mm dia nominal bore

20 mm dia nominal bore

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

Concealed work, including cutting chases and making good the walls etc.

15 mm dia nominal bore

20 mm dia nominal bore

25 mm dia nominal bore

32 mm dia nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

32 mm nominal bore

Providing & fixing unplasticised PVC connection pipe with brass unions

45 cm length

15 mm nominal bore

Constructing masonry Chamber 60x45x50 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. Double flap surface box 400 x 200 x 200 mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:9 (1 cement : 5 fine sand : 9 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Water Tank: Providing and placing on terrace (at all floor levels) polyethylene water storage tank (white color), IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes, but without fittings and the base support for tank.

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) :

80 mm dia nominal bore

Providing and fixing C.I. dirt box strainer for bulk type water meter with nuts, bolts, rubber insertions etc. complete conforming to IS : 2373 :

80 mm dia nominal bore

Providing and fixing gun metal (conforming to IS 318 LTB 2) Non- Return Valve of approved quality (screwed end) and material specification as per specification.

50 mm nominal bore Horizontal

65 mm dia nominal bore Horizontal

80 mm dia nominal bore Horizontal

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality

65 mm dia nominal bore

80 mm dia nominal bore

SEWERAGE AND DRAINAGE

Gully Trap Providing and fixing square-mouth upvc. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design (100x100 mm size P type)

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

350 mm dia. R.C.C. pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1cement :1.5 coarse sand (zone-III):3 graded stone aggregate 20 mm nominal Size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement :2coarse sand:4 graded stone aggregate 20 mm nominal size) fininshed with a floating coat of neat cement complete as per standard design:

Inside size 90x80 cm and 45 cm deep including cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90cm and 90cm deep including . cover with frame (heavy duthy) 560mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg)

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes:

Size 90 x 80 cm

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Size 120x90 cm

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and fixing in position pre-cast RCC manhole covers and frame of required shape and approved quality.

Circular shape 560 mm internal diameter

Constructing brick masonry Road gully chamber 50x45x60 cm with bricks of class designation 75 in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design:

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Description of Work / Item(s)

Amount

Consultancy for obtaining IGBC Certification

Upcoming stations of Phase II

Civil station Junction

Cochin SEZ

Chittethukara

Kinfra Park

Infopark

Description of Work / Item(s)

Amount

Schedule F- Miscellaneous Works Under DSR 2018

Miscellaneous Works Under DSR 2018

Crescent Contractors Pvt. Ltd. (BID ID -2346687)

Crescent Contractors Pvt. Ltd. (BID ID -2346687)

Godrej and Boyce Manufacturing Company Limited (BID ID -2338970)

Godrej and Boyce Manufacturing Company Limited (BID ID -2338970)

Godrej and Boyce Manufacturing Company Limited (BID ID -2338970)

Crescent Contractors Pvt. Ltd. (BID ID -2346687)