PROVN OF RESTAURANT CUM BAKERY SHOP WITH STONE MASONRY WALL FALSE CEILING AND GALVANIZED SHEET ROOF ON TOP OF BUILDING P95 ENHANCEMENT OF AESTHETIC FRONT OF ADMIN BUILDING AND PARAPET WALL ON TOP OF OFFICERS MESS AT CGDHQ 1 PBR

Amount

SCHEDULE 'A'

M&L Cement concrete type B-1, (1:2:4 using 20mm graded stone aggregate) as in cement concrete in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not proivded for in Item 159, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, all as specified and directed by Engineer-in-Charge.

M&L RCC Type A1 (1:1.5:3 using 20mm graded stone aggregate) for slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like etc complete all as specified and directed by Engr-in-charge.

M&L RCC Type A1 (1:1.5:3 using 20mm graded stone aggregate) for chajjas, etc complete all as specified and directed by Engr-in-charge.

M&L RCC Type A1 (1:.1.5:3 20 mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels and the like etc complete all as specified and directed by Engr-in-charge.

Supply only water proofing compound (integral) etc complete all as specified and directed by Engr-in-charge.

Cutting Stone, concrete block or slab walls chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick for fair finished surface (Horizontal or sloping) etc complete all as specified and directed by Engr-in-charge.

Formwork to chullah hoods, chajjas, troughs and similar items including edges as in rough finished surfaces of concrete etc complete all as specified and directed by Engr-in-charge.

Formwork to sides and soffits of beams, bands and the like for fair finished surfaces of concrete etc complete all as specified and directed by Engr-in-charge.

S&F Plain, solid, straight chowkats and frames, of II class hardwood wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints etc complete all as specified and directed by Engr-in-charge.

S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, with particle board core, etc complete all as specified and directed by Engr-in-charge.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

S&F Factory made solid panel PVC cup board shutter 20mm thick (style) shutter reinforced with excellent polymeric reinforcement complete all as specified and as directed.

S&F Factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC Sheet rainforced with MS square tube etc complete all as specified and directed by Engr-in-charge.

S&F solid PVC door frame of size 48mmx40mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying add fixing in opening complete all as specified and as directed.

S&F Aluminium, anodised, barrel tower bolts 200 mm long of extruded section and fixed complete all as specified

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed etc complete all as specified and directed by Engr-in-charge.

S&F Stainless Steel Butt hinges, 100 mm medium weight, etc complete all as specified and directed by Engr-in-charge.

S&F Stainless Steel Butt hinges, 75 mm medium weight, etc complete all as specified and directed by Engr-in-charge.

S&F Extruded aluminium alloy handles, 125 mm , fabricated type, anodised etc complete all as specified and directed by Engr-in-charge.

S&F Extruded aluminium alloy handles, 150 mm, fabricated type, anodised etc complete all as specified and directed by Engr-in-charge.

S&F Tubular towel rail, 60cm long between flanges, Make : Jaquar (Cat Pat No-ACN-CHR-1111NM) or equivalent as approved by GE

S&F Aluminium decorative type powder coated brackets suitable for 20mm dia curtain rod or similar articles complete all as specified and as directed by Engineer in Charge

S&F Door closer aluminium extruded section hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed etc complete all as specified and directed by Engr-in-charge.

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples etc complete all as specified and directed by Engr-in-charge.

S&F 12mm dia Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n. exc 5cm long.

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips. etc complete all as specified and directed by Engr-in-charge.

All as per above item No 27.00 but 6mm dia to 8mm dia. complete all as specified and directed by Engr-in-charge.

All as per above item No 27.00 but 5mm dia and over upto 10mm dia as in stirrups, spacers and binders etc complete all as specified and directed by Engr-in-charge.

M&L Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates (cut to ordinary length) Fe-410, Gde-E-250 etc completed all as specified and directed by Engineer-in-charge.

S&F Powder coated Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified.

M&L 0.9mm thick decorative laminate type 1 of surface finish, colour and patters as approved, fixed with approved adhesive as per manufacturer's insturctions, etc complete all as specified and directed by Engr-in-charge.

M&L Mirror polished Kota Stone slab flooring 20-25 mm thick over cement screed bed 15mm thick 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge.

M&L 18 mm to 20 mm thick Granite of premium quality machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types as in floors (any position) and Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and laid over 15 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and directed by Engr-in-charge.

All as item above but over screed bed or bedding layer 10mm thick 1:4 on vertical surfaces/skirting etc complete all as specified and directed by Engr-in-charge.

M&L Glazed coloured ceramic tiles in verticle surfaces 300x 450x 6-7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match over backing bedding layer 10mm thick 1:4 and pointed in white or coloured cement to match etc complete all as specified and directed by Engr-in-charge.

M&L Non - skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry laid over 15 mm thick bedding layer in Cement Mortar 1:6 etc complete all as specified and directed by Engr-in-charge.

M&L Non skid coloured ceramic tiles mat finish 400 X 400 X 7mm thick set, laid in skirting, over & including a backing coat of 10mm thick in CM 1:3, complete including levelling the wall, all as specified and as directed for :- (Note : Skirting shall be flush with the walls.)

M&L Double charged Vitrified tiles 9 to 10 mm thick dark shade (square/ rectangular) polished, area of each tile exceeding 0.36 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and white or coloured cement to match over screed bed of 15 mm thick 1:6 and pointed in white or coloured cement to match as in floor etc , all as specified and directed by Engr-in-charge.

M&L Double charged Vitrified tiles of size 600 x 600 mm, 9 to 10mm thick, laid in skirting, over & including a backing coat of 10mm thick in CM 1:3, complete including levelling the wall, all as specified and as directed for :- ( Note : Skirting shall be flush with the walls.)

M&L Rendering 10 mm thick on fair face of brick work or concrete surfaces in CM 1:6 finished even and smooth wiithout using extra cement. etc complete all as specified and directed by Engr-in-charge.

M&L Rendering 5mm thick cement plaster in cement mortar 1:3 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement on ceiling in any heightetc etc complete all as specified and directed by Engr-in-charge.

M&L Rendering 15mm thick, cement plaster, in cement mortar (1:4) mixed with integral water proofing compound as per manufactures instruction, on fair faces of brick walls or concrete surfaces finished even and smooth without using extra cement in any height, complete all as specified and directed. Note:- Water proofing compound shall be measured and paid separately) etc complete all as specified and directed by Engr-in-charge.

M&L 3mm thick wall care putty on wall etc complete all as specified and directed by Engr-in-charge.

Preparation of Old treated surface by brushing and washing, rubbing down and applying one coat of primer (acrylic) completed all as specified and directed by Engineer-in-charge.

M&L Preparation of surfaces and applying two coats of cement based paint over a coat of primer complete all as specified and as directed

M&L Preparation of surfaces and applying two coats of white wash on new plastered surfaces of wall complete all as specified and as directed.

M&L Preparation of new plastered surfaces and applying two coat of Oil emulsion Distemper over a coat of alkali resistant priming paint over two coat of wall care putty on new surfaces of wall complete all as specified.

S&F 5mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq.m in each pane all as specified and directed by Engr-in-charge.

S&F Solar control film 50 micron thick reflective type sticked to glass panes as per instructions of manufacturers complete all as specified.

M & L Preparation of new wooden surfaces of any description, not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer of approved shade all as specified and directed.

M & L Two coat of epoxy paint over a coat of red oxide incl preparation of new steel surfaces of any description over 10 cm in width or girth complete all as specified.

S&F 50mm bore High density polyethylene (LDPE) pipes of pressure rating 6kgf/sq.cm laid in trenches or in any position complete all as specified

Disconnecting existing PVC tanks, Exc 500 & n exc 1000 lit capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hositing if required reconnecting and re-fixing in position at hight up to 4mt (Cleaning repairing etc. measured separately).

Cleaning and removing all scale and dirt, etc. from PVC tanks in positions and form mouths of circulating pipes, etc.including disconnecting and reconnencting of the cleaning Exc 500 & n exc 1000 lit capacity.

S&F 1000 litre capacity rotational moulded polythylene water storage tanks (cylindrical, vertical with closed top ) hoisted and fixed in positionall specified in SSR Part-I including provision of 200mm long 50mm bore GI nipples for inlet, outlet, overflow, drain out pipe including provision of check nuts.

S&F Pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed 15 mm dia all as specified and directed by Engineer in Charge. Make Jaquar ( Cat Pat No. CON - CHR - 011KN)

S&F Gun-metal, globe or gate valves 20 mm bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified.

S&F 20mm dia ball valves high pressure of PTMT epoxy coated aluminium rod & high density plastic ball screwed for iron pipes and fixed complete all as specified & directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls of bore 110mm (rates includes for making good disturbed surfaces) etc complete all as specified and directed by Engr-in-charge.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls of bore 75mm (rates includes for making good disturbed surfaces) etc complete all as specified and directed by Engr-in-charge.

S&F PVC (SWR) bends any radius of 75mm bore.

S&F PVC (SWR) bends any radius of 110mm bore.

S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F sinks without drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S & F Vitreous China wash downwater closet pan (pedestalpattern), white (including fixing bolts & flush pipe etc.) complete all as specified and directed by Engineer-in-Charge. Make : Jaquar (Cat pat No CNS-WHT-551PNPP or equivalent as approved by the GE as per the list of makes.

S&F Vitreous China Urinal, Half stall type, white (including flushing cistern and flush pipe and waste pipe) etc complete all as specified and as directed. Make : Jaquar (Cat pat No URS-WHT-13261 or equivalent as approved by the GE as per the list of makes.

S&F PVC low level flushing cistern with dual flushing system including brackets 5/10 litre capacity COMMANDER/SLIM LINE (ISI marks), with 32mm bore polythene flush pipe of sufficient lenght including internal fitting (valve less syphonic) etc complete all as specified and directed by Engr-in-charge.

Supply and lay of CPVC pipes, of 16mm dia SDR -11 including plain CPVC SDR fittings for Hot/cold water for sizes (outer dia ) mentioned below including all fittings and solvents and special fittings like brass elbow, brass tee, male threaded brass adaptor, female threaded brass adaptor etc, Unions, Flange and tank adapter all asper manufacturers recommendations and etc complete all as specified and directed by Engr-in-charge.

Supply and lay of CPVC pipes, of 20mm dia SDR -11 including plain CPVC SDR fittings for Hot/cold water for sizes (outer dia ) mentioned below including all fittings and solvents and special fittings like brass elbow, brass tee, male threaded brass adaptor, female threaded brass adaptor etc, Unions, Flange and tank adapter all asper manufacturers recommendations and etc complete all as specified and directed by Engr-in-charge.

Demolotion of cement concrete reinforced (reinforcement cut as required to facilitate demolition) Roofs, floors (other than ground floors), beams staircases, landing, chajjas, parapet wall, column and similar suspended work

S&F 20mm dia aluminium decorative type powder coated curtain rod or similar articles complete all as specified and as directed by Engineer in Charge

M&L 12mm thick Gypsum Board seamless Ceiling as in curved, sunken or raised surface of any design as approved and finishing the surface fair by filling the joint with POP and applying two coat of Oil Bound Distemper over a coat of primer inlcuding GI frame work for curved, sunken or raised for any design as approved as in ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre fixed with hanger of GI channel made out of GI channel used in ceiling as above upto 1200 mm length in roof slabs by means of ceiling cleats complete all as specified and directed by Engr-in-charge Note :- Flat area will be measured.

M&L 12mm thick Gypsum Board seamless Ceiling as in flat surface, finishing the surface fair by filling the joint with POP and applying two coat of Oil Bound Distemper over a coat of primer inlcuding GI frame work as flat surface approved as in ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre fixed with hanger of GI channel made out of GI channel used in ceiling as above upto 1200 mm length in roof slabs by means of ceiling cleats complete all as specified and directed by Engr-in-charge

S&F Powder coated aluminium anodised Three track sliding window shutter and frame including jointing clit for fixing frame/chowkhat of window as per JINDAL section code (frame 20831), shutter (20846) including glazing with 5mm thick tinted glass necessary fittings, rubber packing, suitable handles, rollers for shutters etc complete all as specified and as directed.

S & F Aluminium powder coated Grill (DECO grill, DG 103 of7.5 mm thick of M/s ELESAR, M/S Royal Grill, M/S National Grill Associated Profiles & Aluminium Ltd.) fixed with suitable 'F' section(No. 8584)15.30 x 23.40 x 1.40mm(minimum), fabricated and riveted to aluminium windows/ventilator complete all as specified and directed by Engineer in Charge.

S & F Glass Mosaic back mounted on link of size tiles 2.5cm x 2.5cm x 4mm thick, on existing columns of any height, of pattern opal series, of make M/s Palladio or equivalent make, surface prepared with a rendering coat of 10 mm thick in CM 1:4, fixed with a backing coat of cementious screed on tiles of make Laticreat or equivalent of approximate thickness 01mm and joints grouted with cementious grout with pigment to match with colour of tiles all as specified by manufacturer's instructions and complete all as specified and as directed by Engr-in-Charge. Note: The colour combination of tiles shall be as approved by the Garrison Engineer.

M & L Granular textured homogeneous wall finishing system consisting of two component system of Dry Granules (25 Kgs per pack) made of 92% Silica Particles coated with fade resisteant pigments, 100% acrylic polymer bonding agent (5 Kgs per pack) with the applied thickness of the coating being between 0.8mm -1.2mm to be applied on a cured , smooth level plaster and previously primed surfaces without keying, as per the shades/combinations approved, as per the manufacturer directions, for usages, to be applied by and approved applicator of the manufacturer, as per the directions/supervision of the Engineer-in-Charge, all complete . The above textured coationg should confirm to surface spread of flame class one of BS 476 : Part 7 : 1971 and pull off strength of the coating top meet JISA 6909 on smooth plastered surface complete all as specified and as per manufacturers specificataions /instructions. complete all as specified and as directed by Engr-in-Charge

S & F 12 mm thick Toughned glass as in Window with Patch fittings with cover plate of SS316 Grade, necessary accessories etc. Including cutting holes in any size in floor and wall etc complete all as specified and directed by Engr-in-charge.

S&F WHB of vitreous china counter sunk any size of including cutting for and pinning in ends of brackets or erecting stand in repairs complete all as specified and as directed by Engr-in-Charge. Make : Jaquar (Cat pat No CNS-WHT-813 or equivalent as approved by the GE as per the list of makes.

S&F Angular stop cock quarter turn with wall flange, Make : Jaquar (Cat pat No CQT-23059 or equivalent, complete all as specified and as directed by Engr-in-Charge

S&F 15mm bore Bib Cock with wall flange quarter turn, Make : Jaquar (Cat Pat No ORP-CHR-10037PM or equivalent, complete all as specified and as directed by Engr-in-Charge

M & L Walling of Porbandar stone masonry , built in CM 1:6 etc completed all as specified and directed by Engineer-in-charge.

M & L Sculpture work (Heritage stone art work) as in parapet wall, in units , as per the length and details shown for each unit, in the drawing, using sand stone of best quality (approved by GE), constructed over existing roof slab of the building, including polishing stone surfaces to natural colour, all as specified and directed by the Engineer-in-charge.

M & L Sculpture work (Heritage stone art work) as in parapet in triangular shape along with stone posts etc in one unit of length 7010mm, as per the details shown on drawing, using sand stone of best quality (approved by GE) constructed on existing roof slab of a building including polishing stone surfaces to natural colour including provn of Ashoka symbol with Indian Coast Guard Logo all as shown on drawing on 1mm thick Stainless Steel Sheet of Size 60 cm X 75 cm fixed to stone masonry with SS fasteners/ brackets , all as specified and directed by the Engineer-in-charge.

S&F 6mm thick plain, multicavity poly carbonate sheet (colored) in roof covering, fixed with and including aluminium fillets at joint and aluminium angle at the ends, fixed with screws and standard fittings, fixturs and accessories complete all as specified and as per manufactures instruction etc completed all as specified and directed by Engineer-in-charge.

S & F Plain fillets, 2nd Class hard wood Sectional area Exc 3 & n. exc 6 sq. cm square, rectangular or traingular in section, wrought, secured with nails or brads, bullnosed, splayed, chamfered or rounded on one edge or face etc completed all as specified and directed by Engineer-in-charge.

S & F Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors,balusters,nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or FE 310-0

M&L Point wiring complete with 1.5 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable 650/1100 Volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit (minimum 20 mm dia external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR part- I ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/ recessed in wall or ceiling etc including 1.5 sqmm PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire including modular type metal flush box with cover plate and frame of required module for mounting of modular switches, sockets, switch sockets, fan regulators with required modules all as specified etc for the following:-

One light /fan point / controlled by one, one way switch

One 3 pin 6 Amps socket outlet on same board

One 3 pin 6 Amps socket outlet on independent board .

M&L Point wiring complete with 2.5 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable 650/1100 Volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit (minimum 20 mm dia external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR part- I ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/ recessed in wall or ceiling etc including 1.5 sqmm PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire including modular type metal flush box with cover plate and frame for modular switches, sockets, switch sockets for one 3 pin 15 or 16 Amps on independent board with required modules all as specified. i Note :- Cost of cutting / chasing on wall and making good after repair deemed to be included in unit Rate

S&F Modular switch 1 way, 6 Amps, 1 modular (ISI marked).complete all as specified and as directed. Make: Hager (Berker)/ Legrand (Arteor)/ Schneider (Zencelo)

S&F Modular switch 1 way, 16 Amps, 1 modular (ISI marked).complete all as specified and as directed. Make: Hager (Berker)/ Legrand (Arteor)/ Schneider (Zencelo)

S&F Modular socket, 6 Amps, 2/3 pin combind 2 module (ISI marked).complete all as specified and as directed. Make: Hager (Berker)/ Legrand (Arteor)/ Schneider (Zencelo)

S&F Modular socket, 6/16 Amps, 2/3 pin combind 2 module (ISI marked).complete all as specified and as directed. Make: Hager (Berker)/ Legrand (Arteor)/ Schneider (Zencelo)

S&F Modular fan regulator, 120 watt, 2 moduler (ISI marked).complete all as specified and as directed. Make: Hager (Berker)/ Legrand (Arteor)/ Schneider (Zencelo)

S&F Ceiling rose, surface bakelite, 65 x 17 mm three terminals (ISI Marked) complete all as specified and as directed. Make: Hager (Berker)/ Legrand (Arteor)/ Schneider (Zencelo)

S&F LED luminaire, aluminium extruded housing, 20 W, lumen output not less than 2000 lm, 220-240 V, 50 Hz, PF> 0.9, CCT 4000K, including connecting cable 2 core 0.5 sqmm from ceiling rose to terminal block complete all as specified and directed. Make: Philips/ Wipro/ GE/ Osram

S&F Distribution Board single phase and neutral 8 way with standard bus bar , Din bar , etc Double door all as spd. Make: Make: Legrand/ Schneider/ ABB/ Seimens Note:- Cost of cutting and modification in false ceiling deemed to be included in unit rate

S&F Isolator SPN 63 Amp 240 volt all as spd. Make: Legrand/ Schneider/ ABB/ Seimens

S&F Isolator SP 40 Amp 240 volt all as spd. Make: Legrand/ Schneider/ ABB/ Seimens

M&L Sub main wiring with two runs of 4.0 Sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 Volts grade cable,fire retardant low smoke drawn through and including PVC concealed conduit heavy duty grade ISI marked 25 mm dia (external) but shall be increased as per actual site requirement in accordance,with wall thickness not less than 1.8 mm complete with all necessary fitting and including with conduit accessories and one run of 2.5Sqmm single core PVC insulated but unsheathed multistranded copper conductor 1100 volts grade cable fire retardant low smoke as earth wire conductor, fixed on wall/ceiling including taking down old unserviceable sub main wiring complete all as specified and as directed Note :- Cost of cutting / chasing on wall and making good after repair deemed to be included in unit Rate

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB

S&F BEE Five Star Rated high speed ceiling Fan, conforming to IS 374, having 1200 mm blade sweep, speed not less than 370 RPM, air flow not less than 210 CMM, operating voltage 220-240 V, and frequency 50 Hz, including a down rod of suitable size and electrical connection with 3 core flexible Cu conductor cable appropriate size from ceiling rose to fan complete with electronic type regulator. Make: Crompton - Empower 50/ Usha (Energia-32)/ Havells/ ES-50 Premium

S&F Exhaust fan 300 mm sweep, 240 V, AC Metal Bosy fixed as per manufacturer's instruction, connecting with and including 2 Core, 0.5 Sqmm Copper Conductor, PVC insulated and PVC Sheathed, 3 core cable, complete all as specified and as directed. Make: CG (Ventulus)/ Havells (Ventil Air)/ Bajaj (Bahar)

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth strip 32 x 6 mm size by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point and provn of earth pit all as specified and indicated including testing on completion.

K K Construction Co

shivshakticonstruction