PROVN OF GUARD ROOM WITH TOILET AND BATHROOM FOR GUARDS, CAR PARKING, HARDSTANDING AND ALLIED WORK NEAR NCC GATE UNDER GE (ARMY) TRIVANDRUM

Amount

Excavating in trenches in hard/ dense soil, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sq m on plan and not exceeding 1.5 mtr in depth and getting out complete all as specified and directed.

Removing excavated materials, soil to a distance not exceeding 50 m depositing where directed at a level 1.5 m above starting point complete all as specified and directed.

Returning and filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with soil obtained from excavation complete all as specified and directed.

M&L for PCC 1:4:8, Type D2 (using 40mm graded stone aggregate) as in foundation, filling mass concrete complete all as specified and directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, exceeding 10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:6) complete all as specified and directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for hardcore (Broken stone Broken or boulders) of gauge exceeding 63 mm but not exceeding 100 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rolled/ rammed to a true surface complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8, type D2 using 40mm graded stone aggregate as in sub-base or similar work complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6, Type C2 (using 40mm graded stone aggregate) as in plinth protection finished surface even and smooth without using extra cement complete all as specified and directed.

S&F TMT bars 10mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

S&F TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

S&F TMT bars 6mm to 8mm dia as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

M&L for PCC 1:2:4, type B1 using 20mm graded stone aggregate for DPC, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, mixed with water proofing compound, including necessary form works complete all as specified and directed. Note: Water proofing compound will be measured and paid separately.

M&L for RCC 1:2:4, type B1 using 20mm graded stone aggregate for shelves, chajjas and similar work complete all as specified and directed.

M&L for RCC 1:2:4, type B1 using 20mm graded stone aggregate for foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC 1:2:4, type B1 using 20mm graded stone aggregate for columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC 1:2:4, type B1 using 20mm graded stone aggregate for beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Use & waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for flat fair finished surfaces of concrete complete all as specified and directed.

Use & waste formwork to sides of pillars, posts, struts, piers, columns and stanchions, as square, rectangular or polygonal, for rough finished surfaces of concrete complete all as specified and directed.

Use & waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for flat fair finished surfaces of concrete complete all as specified and directed.

M&L for finishing walls with acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

M&L for preparing new plastered surfaces applying priming with alkali resistant priming paint and applying two coats of distemper oil emulsion complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying three coats of white wash on ceiling surfaces complete all as specified and directed.

M&L for rendering in two layers 10mm thick with cement mortar 1:6 as under coat and 5 mm thick with cement mortar 1:4 as finishing coat, finishing coat mixed with water proofing compound @ 3% by the weight of cement on fair faces of brick work or concrete surfaces on external surfaces of wall, finishing the surface even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound will be measured and paid separately.

M&L for rendering 10 mm thick cement plaster in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick cement plaster in cement mortar 1:3 on ceiling of concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for PCC 1:3:6, type C1 using 20mm graded stone aggregate for cills and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4, Type B0 (using 12.5mm graded stone aggregate) as in flooring and finishing surface even complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for 10 mm thick screed bed in cement mortar 1:3 on stone/ brick masonry surfaces complete all as specified and directed.

M&L for vitrified ceramic dark shade tiles 10 mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 Sqm, in floors etc, set and jointed neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed.

M&L for vitrified ceramic dark shade tiles 10 mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 Sqm, on vertical surface such as skirtings, dado, and risers to steps etc., set and jointed neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

Use & waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for falt, rough finished surfaces of concrete complete all as specified and directed.

Use & waste formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

M&L for RCC 1:1.5:3, Type A1 (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for rendering 10 mm thick cement plaster in cement mortar 1:3 on fair faces of brick work/ PCC solid block masonry/ concrete surfaces, finished even and smooth without using extra cement, mixed with water proofing compound @ 3% by the weight of cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

Supply only integral water proofing compound complete all as specified and directed.

M&L for water proofing treatment to RCC roof with APP modified prefabricated five layer membrane of 4 mm thick and weight not less than 4.50 Kg per Sqm reinforced with non woven polyster matt reinforcement weighing not less than 150 Gm/Sqm, having softening point not less than 140 degree celsius, longitudinal tensile strength not less than 300 N/ Sqcm, tearing strength of 100 Nm by torch application including minimum 10 cm side lap and 15 cm end lap, over a solvent based bitumen primer @ 0.40 Ltrs per Sqm of same manufacturers conforming to IS 3384-1986 and painting over APP membrane sheet with aluminium bituminous paint @ 0.10 Kg/Sqm complete all as specified and directed.

S&F 25 mm dia drapery rod with a pair of PVC coated MS clamps to hold drapery rod and decorative attachment at one or both ends of drapery rod, fixed to opening of door/ windows (Each opening not exceeding 1.50 mtr, contained with a pair of clamps and a pair of side ornamental attachments) complete all as specified and directed.

S&F pressed steel frames of size 125x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., and applying one shop coat of primer and taring back side of frame complete all as specified and directed.

M&L for second class hardwood plain, framed, panelled shutters 35 mm thickness (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

M&L for second class hardwood glazed and skeleton shutters, 35 mm thick open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate, stove enameled black colour complete all as specified and as directed.

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

M&L for PCC 1:2:4, type B0 using 12.5mm graded stone aggregate for filling in steel chowkats or frames complete all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

M&L for preparation of new or old untreated steel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

S&F 3mm thick sheet plain glass, ordinary quality and glazing with oil putty or fixed with beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, fixing in opening as per specification & drawing complete all as specified and directed.

S&F 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F aluminium anodised tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F corner glass of size 200 mm x 200 mm, fancy type with stainless steel frame and fixed to walls with screws complete all as specified and directed.

S&F brass, chromium plated toilet paper holder fancy type screwed down for fixing to walls with screws complete all as specified and directed.

S&F brass, chromium plated, fancy type, hand shower including flexible PVC pipe with steel lining of 1.50 mtr long, chromium plated, with push button suitable for 15mm pipe complete all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern), white including fixing bolt, seat cover (excluding flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage etc complete all as specified and directed.

S&F PVC connections 15mm size with 02 Nos brass check nuts with washer of length 450mm complete all as specified and directed.

S&F PVC valveless, syphonic action type, flushing cistern 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets for support, low or high density PVC flush pipe complete all as specified and directed.

S&F bib tap of size 15mm bore dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F soap dish, vitreous China white, approximate size 160x 160x90mm fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F vitreous China wash basin, white, flat back, size 550 x 400 mm, including brass chromium plated 32 mm dia with long screwed shanks and fly-nuts waste fitting, PVC medium grade 32 mm dia waste pipe, PVC connection 15mm size with 02 Nos brass check nuts with washer of length 450mm, CI brackets, etc. complete all as specified and directed.

S&F pillar taps of size 15mm bore dia, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts screwed for iron pipe complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks, double wall layer, capacity 500 ltrs (cylindrical vertical with closed top) hoisted and fixed in position, including 20 mm bore dia ball brass valves, high pressure, with polythene float and flynut all as specified in SSR Part I complete all as specified and directed.

S&F 15 mm bore unplasticised PVC pipes of pressure rating 10 kgf/cm2 with all pipe fittings fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed.

S&F 20 mm bore unplasticised PVC pipes of pressure rating 10 kgf/cm2 with all pipe fittings fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed.

S&F 25 mm bore unplasticised PVC pipes of pressure rating 10 kgf/cm2 with all pipe fittings fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed.

S&F 20 mm bore dia. stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 25 mm bore dia. stop valves/ gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes, double socketed, in any length with rubber ring joints or jointing with solvent cement, laid in trenches or in floors complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints or jointing with solvent cement, fixed to walls including brackets complete all as specified and directed.

S&F PVC (SWR) bends any radius with access door for 110mm bore dia pipe complete all as specified and directed.

S&F PVC (SWR) bends any radius with access door for 75mm bore dia pipe complete all as specified and directed.

S&F PVC (SWR) bends any radius for 110mm bore dia pipe complete all as specified and directed.

S&F PVC (SWR) bends any radius for 75mm bore dia pipe complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

M&L for PVC (SWR) floor trap, plain with 75 mm dia of outlet grating including jointing with solvent cement complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, (overall length of cover plate 150mm) fixed in floor complete all as specified and directed.

S&F health faucet (ABS body) chromium plated with push button suitable for 15 mm dia pipe with 1.00 metre long flexible tube with steel lining and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Excavating in post holes (or similar holes) in hard/ dense soil each not exceeding 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 m and making good surface complete in all respect as specified.

M&L for PCC 1:3:6, Type C2 (using 40mm graded stone aggregate) as in foundation, filling mass concrete complete all as specified and directed.

S&F mild steel works for framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. not exceeding 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exceeding 5cm long and 11 to 15 mm diameter of neck complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws or fixed with 'L' or 'J' type or cranked hooks bolts in lieu of screws complete all as specified and directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, exceeding 10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:4) complete all as specified and directed.

M&L for rendering 15 mm thick cement plaster in cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 27cm deep and getting out in hard/ dense soil complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6, Type C2 (using 40mm graded stone aggregate) as in sub base, finishing surface even complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil complete all as specified and directed.

M&L for 100mm thick PCC 1:3:6, Type C2 (using 40mm graded stone aggregate) as in sub base, finishing surface even complete all as specified and directed.

M&L for chequered cement concrete tiles of size 400x400x25mm thick, set, jointed and pointed in neat cement slurry in floors with grey pigment cement and pigments complete all as specified and as directed.

S&F 150/ 160 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints or jointing with solvent cement, laid in trenches or in floors complete all as specified and directed.

M&L for concrete bed to drain pipes 150/ 160 mm bore dia including forming cradles by using PCC (1:3:6), type C2 using 40 mm graded aggregate including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L for rendering 10 mm thick cement plaster in cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, mixed with water proofing compound @ 3% by the weight of cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for precast reinforced cement concrete 1:2:4 type B1, using 20mm graded stone aggregate as in manhole / Gully trap cover slab set in CM 1:6 including use and waste of necessary formwork complete all as specified and directed. (Reinforcement shall be measured separately).

S&F LLDPE septic tank for 25 users, designed to carry sewage and sullage water, including excavation in any type of soil , PCC 1:4:8 as foundation, vent shaft, necessary connections etc complete all as specified and directed by Engineer-in-charge.

M&L for providing soakage well of size 1.80 mtr dia. x 3.00 mtr effective depth, consisting; excavation in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M 25 concrete including intercepting chamber and screen chamber made of brick masonry in CM, RCC cover slab in M 25/SFRC cover, inter connecting pipes of RCC/DWC complete filled with brick bats complete all as specified and directed by Engineer-in-charge.

M&L for point wiring complete for one light point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multistranded copper conductor drawing in and including 20 mm size non-metallic rigid PVC conduit medium grade inclusive of conduit fittings such as bends, tees, reducers, etc and galvanised iron sheet steel terminal boxes of size 16 gauge thickness totally concealed in walls, ceiling, roof, etc for housing light switches, sockets with 3 mm thick bakelite laminated sheet fixed with brass screws and cup washers including one continuous run of 1.50 Sqmm nominal area single core PVC insulated unsheathed FRLS cable 1100 volts grade with multistranded, copper conductor green colour for earth continuity connected to earth dolly complete all as specified and directed.

All as per SI item No. 109.00 here-in-before, but for One exhaust fan point controlled by one way switch complete all as specified and directed.

All as per SI item No. 109.00 here-in-before, but for One fan point controlled by one way switch complete all as specified and directed.

All as per SI item No. 109.00 here-in-before, but for One 5 pin socket outlet 6 Amps, independent, with cables 1.5 sq. mm size complete all as specified and directed.

All as per SI item No. 109.00 here-in-before, but for One 5 pin socket outlet, 6 Amps on the same board with other switches, with cables 1.5 sq. mm size complete all as specified and directed.

All as per SI item No. 109.00 here-in-before, but for one switch socket outlet, 5 pin 16 Amp on independent board with 4.00 Sqmm FRLS cable and 4.00 sqmm cable earth continuity wire complete all as specified and directed.

S&F switch piano, flush type single pole, one way 6 Amp, 240 volts, white or ivory ISI marked complete all as specified and directed.

S&F switch socket combination 2 in 1, 5 pin, 6 Amp flush type, 240 volts, white or ivory ISI marked complete all as specified and directed.

S&F switch socket combination 5 in 1, 3 pin 6A/ 16Amp, flush type, universal, 240 volts, white or ivory ISI marked complete all as specified and directed.

S&F socket outlet 2 in 1, 5 pin, 6Amp, multipurpose, modular type complete all as specified and directed.

S&F ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body 65x50 mm size complete all as specified and directed.

S&F surface and wall mounted LED batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver for and including 1x20 watts ultra bright LED polycarbonate tube light 1200 mm, 6500K, including prewired with 3 core flexible cables of size 24/0.2mm with copper conductor from connector to light fittings & connecting up complete all as specified and directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and directed.

S&F LED light fitting 1x9W/ 1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F distribution board made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, SPN 4 way, 240 volts grade with 200 Amps insulated rated bus bar with nickel plated brass, isolated neutral bar and door earthing, earth bar IP-43 protection with poly urithene (PU) gasketing, IK-08 mechanical impact resistance, flush to wall, including testing suitable for fixing MCB SPN, SP etc, complete all as specified and directed.

S&F distribution board made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, SPN 8 way, 240 volts grade with 200 Amps insulated rated bus bar with nickel plated brass, isolated neutral bar and door earthing, earth bar IP-43 protection with poly urithene (PU) gasketing, IK-08 mechanical impact resistance, flush to wall, including testing suitable for fixing MCB SPN, SP etc, complete all as specified and directed.

S&F sheet metal enclosure powder coated MCCB DB TPN, 415 volts, 4 way, double door, vertical type with 125 Amps rated bus bar din rail neutral link with suitable for MCCB as incomer and providing bottle type copper lugs of different sizes for connection complete all as specified and directed.

S&F MCCB triple pole and neutral (four pole) 125 Amp, 415 volts, 50 Hz, having thermal setting range 70% to 100% and adjustable magnetic setting and breaking capacity 16 KA including making incmoing and outgoing connections complete all as specified and directed.

S&F MCB single pole 5 to 32 Amps current carrying capacity, 240 volts rating, 10 KA, C curve with IP-20 protected terminals including contact indication window, IP-20 protection, energy limitation Class-3, airflow channels on both sides, bi-connect terminals etc., complete all as specified and directed.

All as per SI item No. 128.00 here-in-before, but MCB SPN 32 Amps complete all as specified and directed.

All as per SI item No. 128.00 here-in-before, but MCB TP 63 Amps complete all as specified and directed.

S&F sub-main wiring with 2 runs of 6 sqmm single core PVC insulated, FRLS, unsheathed cable with stranded copper conductor, 1100 Volts grade drawn through and including non metallic PVC conduit with all fitting such as Tees, Bends, Elbows, etc., fixed surface on wall/ ceiling including 6 Sqmm multistranded PVC insulated, FRLS, copper conductor cable as earth continuity conductor and connecting to common earth dolly complete all as specified and directed. NOTE: Two runs of 6.0 sqmm copper cables and one run of 6.0 sq mm copper cable along with white colour PVC non metallic PVC conduit with accessories will be measured as one unit length.

S&F exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed.

S&F ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd. complete all as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.3mm thick buried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below normal ground level, connected to galvanised earth lead of GI wire of size 4mm dia by means of GI Bolts, Nuts, check nuts and washers of the earth and thimbles and other end of the earth GI wire connected to earthing test point and protected by galvanised iron pipe light grade 15mm bore from earth plate to Panel/DBs and water pipe 20mm bore GI medium grade raised up to a level of 50cm above ground level with plug at top, earthing pit in PCC (1:3:6) type C-1, RCC pre-cast (1:2:4 type B-1) cover slab of 50 mm thick using 8.00mm dia CTD bars reinforcement both ways at 140 mm centre to centre with handle, 20 mm dia GI pipe medium grade for watering pipe, wire mesh, funnel and providing charcoal or coke and salt in alternative layers of 15 cm including necessary earth work in soft/ loose soil, returning, refilling and removing of surplus soil to a distance not exceeding 50 mtr testing complete all as shown in electrical plate No-3 of MES Schedule Part-I of SSR-2009 complete all as specified and directed. (Note: If the desired resistance is not find, earthing shall be done by the contractor at no extra cost to Govt.)

S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc. complete all as specified and directed.

S&F 3-layer PP-R (Polypropylene random copolymer) 20 mm outer dia. concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

S&F stop valves 20 mm bore dia., cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F bib tap of size 15mm bore dia, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F LT UG cable XLPE insulated and screened, PVC bedded, galvanised steel strip or wire armoured electric power cable (heavy duty) with stranded aluminium conductor, 1100 Volts grade of cross-sectional area 50 Sq.mm, 3.5 core as per IS 7098 (Part 1) 1988 complete all as specified and directed.

S&F high density polyethylene pipes (HDPE) 40 mm bore of pressure rating 6 kgf/cm2 laid in trenches complete all as specified and directed.

Excavating in trenches in soft/ loose soil, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sq m on plan and not exceeding 1.5 mtr in depth and getting out complete all as specified and directed.

SCION ENTERPRISES (BID ID -3179057)

PINKATRON SECURITIES PRIVATE LIMITED (BID ID -3178424)

mahadeva traders cotractor and suppliers (BID ID -3178483)