SPECIAL REPAIR TO OUTER BOUNDARY WALL FROM NFS NODE TO SARAGARI GATE AND SECURITY RELATED INFRASTRUCTURE ALONGWITH INNER MALA ROAD AT MILITARY STATION KOTA

Amount

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles complete all as specified and directed.

Taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Dismantling precast RCC jallies with care and stacking aside safely, complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep for foundation etc or for shafts, column footings or for laying cables etc not exc 10 Sqm on plan and getting out in soft/loose soil, complete all as specified and directed.

Returning filling in soil including spreading, leveling, watering and well ramming in layers not exc 25 Cm, complete all as specified and directed.

Removing excavated materials (soil) not exc 50 m distance and depositing where directed at a level not exc 1.5 m above starting point, complete all as specified and directed.

M&L Moorum or red bajri filling in floor or paving, laid in layers not exceeding 15 Cm thick, spread, leveled and rammed including watering, complete all as specified and directed.

M&L PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in foundation, filling, mass concreting etc, complete all as specified and directed.

M&L mild steel TMT bars, 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for column, hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

~Ditto~ but 5 to 10 mm dia mild steel TMT bars as in stirrups, spacers and binders etc, complete all as specified and directed.

Formwork (rough finished surfaces) to sides of concrete foundations, column footings, bases of columns, raft and raft beams, sides and soffits of plinth beams or other similar works, vertical or to batter for rough finished surfaces, complete all as specified and directed.

Formwork (rough finished surfaces) to sides of columns, pillars, piers, posts, struts and stanchions etc complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc, under-reamed piles and mass concrete, complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded crushed stone aggregate), as in columns, pillars, piers, posts and struts etc, complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded stone aggregate) as in beams, cantilevers, bressumers, lintels etc, complete all as specified and directed.

Formwork (for fair finished surfaces) to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., complete all as specified and directed.

M&L brick work with pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

M&L walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:4, complete all as specified and directed.

M&L walling of random rubble (Except stone), uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:4, complete all as specified and directed. (Note: Serviceable stone retrieved from demolition shall be reused under this item.)

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses, with maximum depression on face from straight edge held against the dressed surface not exceeding 40 mm; to block in course masonry (Lime or sand stone), complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick work/concrete surfaces in CM 1:6, finishing the surfaces fair and even, complete all as specified and directed.

M&L for 15 mm thick rendering on other than fair faces of brick work or stone masonry surfaces in CM 1:6, finishing the surfaces fair and even, complete all as specified and directed.

M&L for 5 mm thick rendering on surfaces of RCC in CM 1:3, finishing the surfaces fair and even, complete all as specified and directed.

M&L for flush pointing to random rubble stone masonry, uncoursed in CM 1:4, complete all as specified and directed.

M&L preparing newly plastered surfaces of walls and applying two coats of cement based paint over a coat of primer, complete all as specified and directed.

M&L mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

M&L for galvanised, 2 strand steel barbed wire 2.24 mm dia, barbed with 2.00 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rail, straining bolts, incl securing or tying at crossing with and provision of galvanised MS wire, staples or steel pins etc, complete all as specified and directed. (each line wire to be measured).

M & L for preparation of new or previously untreated steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, complete all as specified and directed.

M&L providing precast concrete (1:2:4 type B-0, using 12.5 mm graded stone aggregate) louvers or jallies, 35 mm thick (measured solid), including all mouldings but excluding frame, set in Cement Mortar 1:4, complete all as specified and directed.

M&L for fixing only RCC jalli of any thickness, set in CM 1:4, complete all as specified and direcetd. (Note: Serviceable RCC jallies obtained from dismantling shall be reused under this item.)

S&F PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and fixed to walls/floors, complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work new or old, like ends of posts, backs of chowkhats etc area exc 0.10 Sqm and n.exc. 0.50 Sqm and treating with tar or coal tar black paint, complete all as specified and directed.

M&L for preparing new previously untreated plastered surfaces of walls and applying two coats of modified exterior acrylic emulsion paint over a coat of primer, complete all as specified and directed.

SINGH ENTERPRISES

Ganesh Contruction

M/s Prem Associates

ANNAPURNA ENTERPRISES