CA NO GE(N)AMB-52/2025-26 ADDITION/ALTERATION IN BLDG NO P-28 CW LINE UNDER NCC HQ UNDER AGE B/R-I UNDER GE (NORTH) AMBALA CANTT

Schedule 'A' Part-I (B/R itmes) Surface excavation not exceeding 30cm deep and averaging 15 cm deep, getting out in soft/loose soil complete all as specified and as directed.

Excavation in trenches, not exc 1.5 m wide and not exc 1.5 m in depth for foundation, for laying of cables, pipe etc. or for shafts, wells, manholes etc. not exc 10 sqm on plan and not exc 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed.

Returning filling in including spreading, levelling, watering and wall ramming in layer n exc not exc 25 cm, any kind of soil , complete all as specified and directed.

Removing surplus excavated material to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point , complete all as specified and directed.

Material and labour for providing PCC (1:4:8) Type D2 using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete, complete all as specified and as directed.

Material and labour reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete , complete all as specified and directed.

Material and labour reinforced cement concrete M-25 (Design Mix) using 20mm graded crushed stone aggregate as in columns, pillars, posts,struts, piers, columns and stanchions, complete all as specified and directed.

Material and labour reinforced cement concrete M-25 (design Mix) using 20mm graded crushed stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span , complete all as specified and directed.

Material & Labour for Reinforced cement concrete design mix M-25 using 20mm graded stone aggregate, as in Slabs supported on walls, beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the likedack slab , complete all as specified and directed.

Material & Labour reinforced cement concrete design mix M-25 using 20mm graded stone aggregate, graded stone aggregate as in chajjas,Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels,balustrade, and the like , complete all as specified and directed.

Material and labour formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat rough finished surfaces of concrete , complete all as specified and directed.

Material and labour for form work to sides of pillars, posts, struts, piers, columns and stanchions, work in rough finished square, rectangular or polygonal surfaces of concrete , complete all as specified and directed.

Material and labour form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports overhangs etc., also splays between floors and beams, etc., work in rough finished flat surfaces of concrete , complete all as specified and directed.

Material & Labour form work to soffits of suspended slabs such roof slab, floor slabs, landings and similar work not exceeding 20 centimetre thick (horizontal or sloping) flat for rough finished surfaces of concrete , complete all as specified and directed.

Material & Labour form work to chajjas, fins, louvres, facias including edges for rough finished surfaces of concrete flats , complete all as specified and directed.

Material & Labour TMT steel bars 10mm dia and over cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia , complete all as specified and directed.

Material and labour TMT steel bars 5mm dia and over up to and including 10mm dia in stirrups, spacers etc, cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia, complete all as specified and directed.

Material and labour for brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6, complete all as specified and directed.

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key scrubbing down with water, etc., complete all as specified and directed.

Material and labour for rendering 10 mm thick on any faces of brick work or concrete ceiling surfaces in cement mortar (1:3) and finishing the surface even and smooth without using extra cement , complete all as specified and directed.

Material and labour for preparation of new plastered surface of ceilling applying three coat white wash complete, all as specified and as directed.

Material and labour for rendering 15 mm thick on fair faces of brick work or concrete wall surfaces, etc. in cement mortar (1:6) and finished even and smooth without using extra cement , complete all as specified and directed.

Material and labour for preparation of new plastered /concrete surface of wall applying of two coats of acrylic distemper over a coat of primer complete, all as specified and as directed.

Material and labour rendering 15 mm thick on brick work or concrete wall surfaces in cement mortar (1:4) including mixing water proofing compound @ 2% by weight of cement or as per manufacturer's instruction and finished fair and even without using extra cement complete all as specified and as directed by the Engineer-in-Charge. ( Note- The cost of providing WPC shall be included in quoted rate under this item )

Material and labour preparation of new decorated brick/concrete, plastered / unplastered surfaces of walls applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior grade paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre per 10 Sqm up to height of triple storey bldg, including necessary scaffolding etc , complete all as specified and directed.

Material and labour for preparation of new plaster surface on walls and applying two coats of cement based paint over a coat of alkali resistant primer , complete all as specified and directed.

Material and labour for preparation of old plastered/unplastered surfaces and applying two coats of white lime wash on surfaces of ceiling, chajjas, roof projection etc., complete all as specified and directed.

Material and labour for preparation of old plastered/ unplastered surfaces of walls and applying two coats of acrylic distemper with painting roller over and including 1 to 2 mm thick wall care putty white cement based in one or two coats to achieve smooth surfaces, complete all as specified and directed.

Material and labour for preparation of old plastered/unplastered surfaces of walls, chajjas, roof projection, etc. and applying two coats of cement base paint , complete all as specified and directed.

Supply and fixing 12 mm thick costomized and moulded toughened glass as in partition, door, fixed with patch fittings of stainless steel grade 304 or any suitable fittings of stainless steel grade 304 as required (fixing of glass should be top to bottom and any cutting required shall be done with diamond blade) including drilling holes for patch fittings and spider fittings as required and locking arrangement , complete all as specified and directed.

Supply and fixing 25 to 30mm size stainless steel channel of grade 304 in floor including cutting in any floor finish and embedding the channel for receving the glass including silicon filling etc, complete all as specified and directed.

Supply and fixing 05mm thick frosted sheet glass ordinary type and glazing with aluminium beading, rubber packing , complete all as specified and directed.

Material & Labour sheet glass 3.00mm thick tinted ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane, complete all as specified and directed by Engr-in- charge.

Supply and fixing for galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples , complete all as specified and directed.

Supply and fixing factory made uPVC white colourThree track three panels sliding window with fly proofS.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weatherproof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing of 150 mm long aluminium handle, cast type, anodised , complete all as specified and directed.

Supply and fixing of 150 mm long, aluminium anodised, barrel tower bolts of extruded section , complete all as specified and directed.

Supply and fixing of butt hinges 100mm long of mild steel, medium weight,, complete all as specified and directed.

Supply and fixing powder coated aluminium section (minimum thickness of powder coating 50 micron) for doors,windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/panelling, C.P. brass/ stainless steel screws complete all as specified and as directed by the Engineer-in-Charge. Note : (a). Glazing shall be measured and paid separately; (b). Weight of aluminium sections shall be as per IS or actual weight which ever less shall be measured. (c). The rates quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screws, etc as required and the same shall not be measured for arriving the weight; (d). The rates shall be inclusive of locking arrangement including complete packing with silicon gel all around contacting surface of aluminium framework and including matching the existing surface area complete all as specified and directed.

Supply and fixing of double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty as in repair , complete all as specified and directed.

Supply and fixing 12 mm thick prelaminated particale board,interior grade, prelaminated both side with decorative choice lamination and fixed to aluminium door with glazing clips, rubber gasket etc , complete all as specified and directed.

Supply and fixing 100mm long mortice latch with two levers (vertical type),mild steel body , complete all as specified and directed.

Material and labour 100 mm thick PCC 1:4:8 Type D–2 using 40mm graded crushed stone aggregate as in sub base of floor/ hard standing etc and finished even and fair without using extra cement , complete all as specified and directed.

Material and labour for vibratory rubber moulded coloured precast concrete interlocking paver block, any shape and size conforming to IS 15658-2006, ISI marked of 60 mm thickness, grade M-35 with grey cement and pigments over and including a layer of sand cushioning, 25 mm thick , complete all as specified and directed.

Material and labour for 25 mm thick PCC 1:2:4, type B0 as in sub base of floor (using 12.50mm graded crushed stone aggregate), finished even & fair without using extra cement , complete all as specified and directed.

Material and labour for glazed ceramic coloured tiles joint free premium/1st quality in vertical surfaces/skirtings/dados of size 300x 600x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on faces of brick / concrete surfaces in cement mortar 1:4 , complete all as specified and directed.

Material and labour for black granite (of any type) tiles 16–18mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types over and including 15mm thick screed bed in CM (1:4) and including rounding to edges of stone slabs one edge, such as in steps, cooking platform, pillars, windows cills and other similar situations and including making holes for gas pipes or WHB outlet /inlet , complete all as specified and directed.

Material and labour providing 50 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (not exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight including form work , complete all as specified and directed.

Supply and fixing 110mm dia PVC (SWR), soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, , complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 110 mm bore PVC (SWR) plain bend any radius including jointing with solvent cement, , complete all as specified and directed.

Supply and fixing 150mm dia PVC (SWR), soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in trenches, complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Material and labour for providing precast cement concrete (1:2:4) type B1, using 20mm graded crushed stone aggregate as in landings, precast cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weathering, throating, etc. and setting in cement mortar (1:4), complete with joints to match, complete all as specified and as directe.

Supply and fixing Stack clamp out of 50mm x5mm flat iron stays including bolt and nuts and securing ends of stays to walls or roof for 75mm bore pipe., complete all as specified and as directed.

Material and labour for concrete bed in PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate to drain pipes including packing under and haunching against the sides of pipes, after they are laid and tested for 150 mm dia (internal) pipes complete all as specified and as directed. (Pipes shall be measured & paid separately).

Cutting into existing manholes for connecting new drains, and making good to pipe and rendering, cutting out existing benching for and forming branch channel( 1/2 round or 3/4 section ) in cement concrete 1:2:4 type B-1 (using 20mm size crushed stone aggregate) smooth finished and reforming benching as required of pipe 110 mm dia, complete all as specified and as directed by the Engineer-in-Charge.

Material & Labour for providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt and consisting of a coat bituminous primer @ 0.40 litre /Sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25 degree centegrate temperature and viscosity 70–160 cps over the primer coat with overlap of 100mm at the side and 150mm at the end, the layer membrane shall be laid using butane gas torch and sealing all joints etc. after preparing the surface complete as per standred practice as per manufacture's instructions. The vital physical and chemical parameters of the membrane shell be under :– (i) Joint strength in longitudinal and transverse direction at 23 degree centegrate at 650/ 450 N /5 cms (ii) Tear strength in longitudinal and transverse direction at 300/250N/5 cms. Softing point of membrane not less then 150 degree centegrate when tested in accordance with ASTM (d–5147) (iii) The laying of membrane shell be got down through the authorised applicator of manufactures of membrane only , complete, all as specified and as directed. (iv) The work shall be carriout at a height upto 12 metre.

Material and labour for providing cement concrete 1:2:4 Type B1 using 20mm graded crushed stone aggregate as in roof kerbs or mud stops, padding, rounded or chamfered on edges including from work where ever required , complete, all as specified and as directed.

Material and labour for PCC 1:2:4 type B1 using 20mm graded aggregate as in coping & the like including weathering slightly rounded or chamfered angles & throating etc including necessary form work complete all as specified and drected.

Material and labour for brick work with sub class B bricks old size bricks, straight or curved on plan any radius in cement mortar 1:4 in half brick thick wall , complete all as specified and directed.

Supply and fixing providing cement concrete (1:2:4) Type B1 using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating , complete all as specified and directed.

Supply only integral water proofing compound, complete all as specified and directed.

Material and labour for cutting out concrete blocks, slabs, brickwork or stone masonry (in alternate course), forming toothings and bonding new work in CM 1:4 into old work, including new materials entering old wall PCC 1:2:4 type B1 using 20mm graded stone aggregate , complete all as specified and directed.

Dismantling of brick work or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillar, etc. but excluding ashlar facing, dressed stone work and precast concrete articles , complete all as specified and directed.

Demolition of cement concrete (un–reinforced) in ground floors and pavings not exe 15 cm thickness (below or above ground level) , complete all as specified and directed.

Demolition of reinforced cement concrete for roofs, floor, beams, staircases, landing ,chajjas and similar susended work, complete all as specified and as directed. (Reinforcement cut to facilitate demolition)

Taking down chowkats or frames with shutter area not exceeding 1.50 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish, complete all as specified and directed.

Taking down chowkats or frames with shutter area exceeding 1.50 Square meter and not exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises , complete all as specified and directed.

Material and labour for vitrified ceramic tiles, double charged light shade,1st quality,(square/ rectangular), 9 to 10mm thick, area of each tile exceeding 0.42 sqm and not exc 1.00 sqm as in floor, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed or bedding layer 15 mm thick in cement mortar (1:4) for laying floor finishes , complete all as specified and directed.

Material and labour for vitrified ceramic double charged light shade tiles, 1st quality, of same description as of floor tiles in serial item No. 70 above but 100mm to 150mm height as in skirting, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including rendering 10 mm thick in cement mortar 1:4 , complete all as specified and directed.

Material and labour for 16 mm thick heavy duty full body vitrified coloured paver tiles of size 600mm x 600mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar (1:4) , complete all as specified and directed. Make: Endura of Johnson or Durastone of Somany or equivalent make given in App ‘B’

Material and labour PCC Tiles (300 mm x 300 mm x 20 mm) iaid over sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of cement & sand in ratio of 1:1, including providing skirting upto 150 mm height along the parapet walls all as specified and as directed.

Supply and fixing hollow PVC wall lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site specifications and drawing, complete all as specified and as directed.

Schedule 'A' Part-II (E/M itmes) Material and labour for point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling surfaces and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade, ISI marked with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes modular type of size/modules as required at site with earth dolly (boxes shall be galvanised or painted with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally) including provision of new covered plate over sunken box for housing the modular switches , modular socket outlets,modular fan regulators etc. for one light/fan/exhaust fan/bell point controlled by one way switch, complete all as specified and as directed by Engineer-in-Charge. Note :- a) All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid for separately .

Description all as per serial item No.75 here-in-before but for One 3 pin, 6 Amps, socket outlet controlled by one switch on independent board, complete all as specified and as directed by Engineer-in-Charge.

Description all as per serial item No.75 here-in-before but for One 3 pin 6 Amps socket outlet controlled by one switch on same board, complete all as specified and as directed by Engineer-in-Charge.

Description all as per serial item No.75 here-in-before but for one socket outlet 16 Amp with 2.50 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 2.50 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade, ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly, complete all as specified and as directed by the Engineer-in-Charge. Note : (i) Point wiring shall be done in a manner that not more than 02 socket point executed in one circuit. (ii) Each socket point will be measured and paid as per point.

Description all as per srl item No 127 here-in-before but for one socket outlet 16 Amp with 4.00 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 4.00 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly, complete all as specified and as directed by the Engineer-in-Charge. Note : (i) Point wiring shall be done in a manner that not more than 01 socket point executed in one circuit. (ii) Each socket point will be measured and paid as per point.

Supply and fixing of modular switch 1 module, single pole, one way 6 Amps flush type, 230 volts, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular switch 1 module, single pole, one way 16 Amps flush type, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular socket outlet multipin combined, 6 Amp, one way, two module, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular socket outlet multipin combined, (6pin), 16 Amps, one way, two module, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing ceiling rose surface type 2/3 terminal polycarbonate, isolated body complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair, LED surface mounted bulk head luminaries, 8-10 watts, with min 800 lumen, industrial model, IP 65, aluminium housing, surge protection including driver and LED lamp, etc. complete with all accessories, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge. Cat part No. HEXAFT10WLED857SSYMBOPC of make Havells or equivalent in make given in Appx 'B'.

Supply and fixing in repair LED batten fitting 20 watt, 4 feet, polycarbonate housing with electronic driver cool/warm type, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LBLN-20-C-SQ of make Orient or equivalent in make given in Appx 'B'.

Supply and fixing in repair, LED Bldg Security Light Fittings of capacity 40-45 watt made up of die cast aluminium housing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including electronic driver and making electrical connection, complete all as specified and as directed by the Engineer-in-Charge. Cat part No.LSFS-45-CF-PC of make Orient or HLSLD-14-40-CWDL-R01 of make Halonix or equivalent in make given in Appx 'B'.

Supply and fixing in repair, 9/12 watt thermoplastic wall mounting fixture (sketch type) with B-22 LED lamp and including connecting with copper conductor flexible cable from ceiling rose to connector of the light complete and removing unserviceable light fittings complete all as specified and as directed by the Engineer-in-Charge. Cat part No.DECO WALL LIGHT FROSTED of make Orient orLHFOGBE1TZ1W035 of make Havells or equivalent in make given in Appx 'B'.

Supply and fix sheet metal MCB DB SPN 8 way with 200 Amps rated bus bar single pole and neutral with double door IP-43 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811807 of make Indo Asian or equivalent in make given in Appx 'B'.

Supply and fixing MCB SP, 6-32 Amps, 240 volt,10 KA , 'B' curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed by the Engineer-in-Charge. Cat part No 811008 to 811015 of make Indoasian or equivalent make given in Appx 'B'.

Supply and fixing MCB SPN 32 Amps, 240 volt,10 KA , 'B' curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed by the Engineer-in-Charge.Cat part No 811035 of make Indoasian or equivalent make given in Appx 'B'.

Supply and fixing BLDC ceiling fans 1200mm sweep complete with blades, down rods, and all accessories, 230 V, 50Hz, value BEE 5 star rating, copper winding opal white colour including making electric connection with 3 core PVC flexible cable 1.5 sqmm complete all as specified and directed by Engr-in-Charge.

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCBs 20 Amps, 10 KA 'B' curve including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811955 of make Indo Asian or equivalent in make given in Appx 'B'.

S & laying as in repair sub main wiring with two run of 6 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 6 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium grade ISI marked of adequate size for housing the wires complete all as specified and as directed by the Engineer-in-Charge.Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length.

S & laying as sub main wiring with four run of 10 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 10 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium grade ISI marked of adequate size for housing the wires complete all as specified and as directed by the Engineer-in-Charge.Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Five runs of cable and one run of PVC conduit shall be measured and paid as one unit length.

Supply and fix sheet metal enclosure Vertical triple pole & neutral(VTPN) IP-43 suitable and including MCCB 125 Amp, 16 KA, 415 volts, 4 way with 200 Amp rated bus bar flush /surface mounting double door duly grouted in solid block wall or on wooden board in and including lugs/thimbles duly crimped for connection including making smooth the disturbed surface including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811888 of make Indo Asian or equivalent in make given in Appx 'B'.

Material and labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15mm bore(medium grade) and connected to earthing test point as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm c/c both ways with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing as in repair complete all as directed by Engineer-in-Charge and earth testing on completion.

Note:- Amount of credit of Rs.2,650.00 for retrieved materials is mentioned in Schedule of Credit Page No 123..of tender documents in pdf form which will be deducted offline while acceptance of tender.