Special repair to bldg No. P 35,P 37,P 38,P 39,P 40,P 41 and floor tiles,wall tiles and Sanitary fittings of bldg No P 1 and P 2 and Provision of cover slab for open drains under GE ND,Visakhapatnam

Amount

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment along external walls below concrete or masonry apron using chemical emulsion @ 2.25 litres per RM by drilling 12 mm dia holes up to 300 mm deep and 300 mm centre to centre including plugging holes complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment of soil under existing floors using chemical emulsion @ 1 litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified and as directed

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment at points of contact of wood work by chemical emulsion [in oil or kerosene based solution] @ 0.5 litre per hole by drilling 6 mm dia holes at a downward angle of 45 degrees at 150 mm centre to centre and sealing the same complete all as specified and as directed.

Demolition of Unreinforced Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] and removing rubbish to a distance exceeding 1.50 KM but not exceeding 5.00 KM complete all as specified and as directed.

Demolition of Reinforced Cement Concrete as in Roof, Floors , beams, staircase, landing, Chajjas and similar suspended work including reinforcement cut as required to facilitate demolition and removing rubbish to a distance exceeding 1.50 KM and not exceeding 5.00 KM complete all as specified and as directed.

M & L for RCC 1:1½:3, Type A-1, using 20mm graded stone aggregate as in Slabs supported on walls, beams, columns, landings, shelves, Chajjas and the like complete all as specified and as directed.

M & L for 100 mm thick (average) PCC 1:2:4, Type B-1 [using 20 mm graded granite stone aggregate] as in forming of surface channels and drains including finishing the surface even and smooth using extra cement including forms, moulds, mitred / stooped ends complete all as specified and as directed.

M & L for Forming Contraction Joint [Dummy], 30mm deep X 10mm wide, filled with sealing compound and sealed with Sealing Compound Grade "A" for 100mm thick flooring complete all as specified and directed.

M & L for 75mm thick PCC 1:3:6, Type C-1, using 20mm graded aggregate as in Plinth protection etc surface finished even and smooth with out using extra cement and providing 12mm thick joints for full depth of PCC at every 3.00 m and every change of direction duly filled with mastic filling comprising of 01 Part of heated bitumen blown grade of any penetration and 3 parts of sand [all by weight] complete all as specified and as directed.

M & L for 100 mm thick, PCC 1:2:4, Type B-2, using 40mm graded stone aggregate as in Floors/ Hard standing etc, surface finished even and smooth with out using extra cement and spike rolling to surfaces or making impressions of expanded metal, while the concrete is green complete all as specified and as directed.

M & L for PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for providing Precast RCC 1:1½:3, Type A-1 using 20mm graded stone aggregate as in landings, cover slabs [for manholes etc], chullah hoods, chajjas, water troughs, mangers, Shelves and similar articles with plain faces set in cement mortar 1:4 complete all as specified and as directed.

Use and removal of steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including rough finished surfaces complete all as specified and directed.

M & L for Cutting / Chipping the spalling concrete surfaces of Slabs, Beams, Columns, Fins, Facias, Parapets & Chajjas etc. and trimming, cleaning the surfaces of any thickness to receive Guniting / Plastering, preparing surfaces and applying a coat of Nito Bond AR of M/s. Fosroc Chemicals or equivalent approved bonding agent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. as per manufacturer's instructions and providing pressure Guniting averaging 25mm thick at a pressure of not less than 6 KG / Sq.cm in Cement Mortar 1:3 with and including suitable bonding agent of M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. @ 5% of weight of cement for sides and soffits of Slabs, Beams, Columns, Fins, Parapets Facias & Chajjas etc., finishing surface rough conforming to proper geometrics including providing double scaffolding and safety measures as required and removal of the same on completion and disposal and depositing the demolished material to a distance exceeding 1.5 KM but not exceeding 5 KM complete all as specified and as directed.

M & L for Cutting / Chipping the spalling concrete surfaces of Slabs, Beams, Columns, Fins, Facias, Parapets & Chajjas etc. and trimming, cleaning the surfaces of any thickness to receive Guniting / Plastering, preparing surfaces and applying a coat of Nito Bond AR of M/s. Fosroc Chemicals or equivalent approved bonding agent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. as per manufacturer's instructions and providing pressure Guniting averaging 40mm thick at a pressure of not less than 6 KG / Sq.cm in Cement Mortar 1:3 with and including suitable bonding agent of M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. @ 5% of weight of cement for sides and soffits of Slabs, Beams, Columns, Fins, Parapets Facias & Chajjas etc., finishing surface rough conforming to proper geometrics including providing double scaffolding and safety measures as required and removal of the same on completion and disposal and depositing the demolished material to a distance exceeding 1.5 KM but not exceeding 5 KM complete all as specified and as directed.

Demolition of Brick / Stone Masonry built in Cement Mortar including all quoins arches pillars etc and removing rubbish to a distance exceeding 1.50 KM and not exceeding 5.0 KM complete all as specified and as directed.

M & L for brick work with Fly Ash bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

M & L for brick work in half brick thick walls using Fly Ash bricks straight or curved on plan to any radius built in Cement Mortar 1:4 including 2 Nos of 8mm dia bars at every fourth course of brick work complete all as specified and as directed.

Cutting chases, pinning in Brick Walls, making good to facings where required and pointing in Cement Mortar 1:3 to ends or edges of landings, steps, Cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10 cm girth complete all as specified and as directed.

M & L for cutting holes into or through cement concrete slabs reinforced or otherwise for superficial area exceeding 100 Sq.cm and not exceeding 150 Sq.cm complete all as specified and as directed.

Taking down Chowkats or frame with shutters [without taking off shutter from the frame] not exceeding 1.5 Sq.m each complete all as specified and as directed.

Taking down Chowkats or frame with shutters exceeding 1.5 Sq.m but not exceeding 4.00 Sq.m each complete all as specified and as directed.

Taking wooden down shutters of any description exceeding 2 Sq.M each.complete all as specified and as directed.

S & F in repairs Steel rolling shutters, thickness of laths of 1.25 mm, with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, Gear Operated type with bevel gear box and crank handle complete all as specified and as directed. Note: Safety lever lock and ball bearing shall be measured and paid separately at supply only rates.

M & L for Powder coated aluminium sections [Minimum 50 Micron thick] of approved colour for Doors, Windows, Ventilators, Partitions with frame and shutters fully or partly glazed, sliding / openable including necessary jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts, stainless steel friction hinges, locking arrangements etc. including taking down existing doors/windows/Ventilators/Partitions and making good to disturbed surfaces complete all as specified and as directed. Notes: [a] The size of aluminium sections shall be all as specified in relevant IS code and MES Schedule Part - I. [b] Panel inserts such as Glass / Particle board / Gauze shall be measured and paid separately at supply only rates. [c] Weight of aluminium sections shall only be accounted for payment purpose. Weight of aluminium Handles, Butt Hinges & Tower Bolts shall not be accounted for payment purpose. [d] The unit rate quoted shall be deemed to include for cost of jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts, stainless steel friction hinges, locking arrangements etc., and fixing only of panel inserts of glass / particle board / gauge etc.

Supply only 5.5mm thick Sheet Glass ordinary quality in squares exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

S & F 5.5mm thick Sheet Glass ordinary quality in squares exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

Supply only 12mm thick, Prelaminated Particle Board with Decorative Choice Laminated on both sides , Exterior Grade complete all as specified and as directed.

Supply only Stainless steel wire cloth / mesh with average aperture not exceeding 1.40 mm and dia of wire 0.36 mm complete all as specified and as directed.

S&F aluminium powder coated grill of make "Deco grill" of DG - 104 model with apperture of size 105 x99 mm with suitable outer channel 'U', ''F'' or ''E'' section fixed to window/ventilator frame for securing Deco grill and interlock and secruing the frame to masonry wall with brass screws complete all as specified and directed.

S & F Solid PVC door frame of size 50mmX47mm made out of 5mm WPC sheet reinforced with MS square tube in opening of Sintex ot its equivalent make as approved by GE complete all as specified and as directed.

S & F Second class hard wood small fittings such as brackets of any type, shaped door and window stops and the like including all necessary Labour, articles not exceeding 200 Cu.cm each complete all as specified and as directed.

S & F Second Class Hard Wood, plain, solid, straight Chowkats and Frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick [Style] consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC "C" Channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement fixing in frame at site as per specification complete all as specified and as directed.

S & F 35mm thick Factory made, Second Class Hard Wood, Glazed and Skeleton Shutters, open rebated and prepared to receive glass, gauze, etc., divided into squares, with plain, chamfered or rounded, mitred and rebated Sash Bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part – I, Section 8, Clause 8.24 [b] and fitted to Chowkats complete all as specified and as directed.

S & F Factory made 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S & F 18mm thick marine Plywood, Grade BWR, Type BB, including providing .9 mm thick decorative laminates on both side with approved adhesive fixed with screws to Wooden Frames complete all as specified and as directed.

S & F in repairs Stainless steel kitchen sink with drainage board, made of stainless steel sheet of 1 mm thick, with plugs, washers, Waste Fittings, 32 mm dia, Brass, Chromium plated, and 32mm dia PVC flexible Waste Pipe, 750 mm long, including bedding in Cement Mortar to dwarf wall or including fixing cantilever CI Brackets and connecting union to waste pipe, over all size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed.

S & F in repairs Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples or with existing or new wooden beading including necessary painting to beading to match with existing surfaces complete all as specified and as directed.

S & F in repairs Decorative type Stainless Steel Curtain Rod of 25 mm dia including PVC rings @ 100 mm centre to centre and Decorative type brass Globe type Brackets of size suitable to 25mm dia curtain rod complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt of size 200 mm size of extruded section complete all as specified and as directed.

S & F 150mm Aluminium Alloy barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and as directed.

S & F 100 mm size, Butt hinges, Extruded Aluminium alloy with galvanised mild steel hinge pin, anodised, Type C-21, including fixtures complete all as specified and as directed.

S & F Aluminium alloy anodised Sliding Door Bolt with hasp and staple [Bolt Type] of size 250 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F 300mm size mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S & F in repairs Stainless Steel Kitchen Plate Rack of size 750x600x250mm, made of 1.50mm thick stainless steel sheet including taking down of existing unserviceable stainless steel plate rack of any size and description complete all as directed. [Make: Prayag / Nirali / Jayna / Blue star]

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

Dismantling of Mild Steel or Wrought Iron Work of any description not otherwise provided for complete all as specified and as directed.

S & F Mild Steel work confirming to Fe - 290, Grade E-165, as in framed work such as Grills, Gratings, Ladders etc with ends of bars shouldered and/or riveted, or forged into spikes, framed Guard Bars, Barred Iron Doors, Ladders, framed Balusters, Walk Ways, Railings, framework of Water Tanks and similar work complete all as specified and as directed.

S & F Mild Steel work conforming to Fe - 290, Grade E-165 as in Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes, including Bolts, if required, Hooks [Stay], heavy, for Large Gates, Hook and Pintle Hinges, large Hasps and Staples, Chains, hand made Sliding Bolts, Clamps, Hold Fasts, Wall Ties, Hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

Dismantling of Wall & Ceiling Boards [Fibre / Pulp / Insulation etc] of any description or Insulation Boards / Slabs / Blankets including cover fillets complete all as specified and as directed.

S & F Calcium Silicate False Ceiling at all heights in true horizontal level made out of Calcium Silicate Tiles of size 595 X 595 mm, having Integral densified reinforced edges of 15mm thickness all around with a collar of width 24mm and 10mm thickness at the centre of siliceous and calcareous material reinforced with cellulose fibre of approved texture, design and patterns, suspended on the Exposed Metal Frame Ceiling Grid of 600mm x 600mm size and applying two coat of plastic emulsion paint and including suspended Exposed Inter-locking Metal Frame Work using GI Main "T" Runner of size 24x38mm, 0.33mm thick, spaced 1200mm centre to centre, Cross "T" of size 24X32mm, 0.33mm thick, 1200 mm long spaced between Main "T" at 600 mm centre to centre to form a grid of 1200X600 mm and secondary Cross "T" of 600mm long and of size 24X32mm, 0.33mm thick of the 1200x600mm panel to form grid of size 600x600mm, resting on periphery walls / partitions on GI Perimeter Wall Angle of size 24X24X3000 mm, 0.40 mm thick with the help of rawl plugs at 230mm centre to centre with 40mm long dry wall SS Screws including cutting/making opening for services like diffusers, grills, light fittings, smoke detectors etc., wherever required. Main "T" Runners shall be suspended from ceiling using galvanised mild steel [Galvanizing @ 80 Grams per Sq.m] 50 mm long, 8 mm outer diameter M-6 Dash Fasteners, 6 mm dia fully threaded hanger rod up to 1000 mm length and L-Shape level adjuster of size 85x25x25x2 mm, spaced at 1200mm centre to centre along Main "T". Bottom exposed width of 25 mm of all sections shall be pre-painted with polyester baked paint at all heights complete all as specified and as directed.

Dismantling of Plain or Corrugated Steel sheeting of any gauge, thickness of roof in roof coverings, complete all as specified and as directed.

S & F pre-painted Galvalume steel sheets of Trapezoidal profile having pitch 190mm, depth 29mm or Tiled Profile and thickness 0.50mm [Galvalume base-PPGL trapezoidal profile sheets], having tensile strength of 550 Mpa, fixed with aluminium self tapping screws, neoprene and EPDM washers of suitable size in roof covering complete all as specified and as directed. Note: Overlap shall be provided as specified by the manufacturer.

S & F pre-painted Galvalume steel Plain Sheets and thickness 0.50mm [Galvalume base-PPGL Sheets], having tensile strength of 550 Mpa, in ridges, hips, valley gutters, drip and straight flashing cut to length & bent to shape, girth sheets fixed with aluminium self tapping screws and neoprene and EPDM washers of suitable size in roof covering / cladding / eves trim / rake trim and closure trim / valley rain water gutter/ down spouts and top rafters etc. complete all as specified.

Dismantling of Floor, Hearth or Wall Tiling of any description including Cement Mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris to a distance exceeding 1.50 KM but not exceeding 5.0 KM complete all as specified and as directed.

Dismantling of sand stone slabs and tiles in flooring, apron etc of any description or thickness laid dry and pointed in any mortar complete all as specified and directed.

M & L for PCC 1:3:6, Type C-1, using 20 mm graded stone aggregate as in Coping, Bed plate,Plinth course,hold fast cill and the like including weathering, slightly rounded or chamfered angles and throating including formwork [straight or curved] complete all as specified and directed.

M & L for Plain Cement Concrete Tiles of size 250 X 250 mm / 300 X 300 mm, 22mm thick, Hydraulically pressed as in Floors, set jointed and pointed in neat cement slurry to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 of cement complete all as specified and as directed.

M & L for designer pre-polished coloured chequered cement concrete Tiles of size 250 X 250 mm / 300 X 300 mm, 25mm thick, Hydraulically pressed as in Floors, set jointed and pointed in neat cement slurry to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed.

M & L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M & L for Inter Locking Paving Blocks of 60mm thick, made with M-35 Grade cement concrete using 20 mm graded stone aggregate, Hydraulically pressed of approved colour and pattern conforming to IS - 15658 set in floors complete all as specified and as directed.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.06 Sq.m and not exceeding 0.11 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.18 Sq.m and not exceeding 0.38 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Joint Free Glazed Ceramic Tiles, Edge Cut, Concept Type, Coloured, Premium Quality, of size 300 mm X 450 mm, 7 to 8 mm thick as in Vertical Surfaces such as Skirting, Dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. The colour / shade / design of tiles shall be as approved by GE.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, of size exceeding 0.18 Sq.m and not exceeding 0.38 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in vertical Surfaces such as Skirting, Dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed.

M & L for applying 2mm thick Cement based Wall Care Putty on walls surface and finishing the surface even and smooth complete all as specified and as directed.

M & L for Marble Stone Slabs of 18 to 20 mm thick of Green Colour as in Flooring, Treads, Landings of Staircase, Window Cills, Cooking Platform etc. with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, slabs shall be of design / pattern as directed, including inlays, borders, margins, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious joint filler to match the shade of the Slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 and grinding & polishing after laying of slabs to mirror polish [Tin Oxide Polish] complete all as specified and as directed. Note: Single stone slab shall be used for entire width of Cills & Landing etc. and joints shall match with the flooring. The edges of Window Cills, Treads shall be bull nosed / half rounded. The edges of the treads and landings shall also be provided with three Nos of grooves.

M & L for machine cut Kota stone slab flooring using 20 to 25mm thick slabs, laid and jointed with grey cement slurry mixed with a admixture of pigment to match shade of slab including rubbing and polishing to smooth mirror finish all to required sizes, the size and design / pattern of slabs shall be as directed, including diagonals, inlays, borders, margins in two or more shades of slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed.

M & L for machine cut Kota stone slab as in riser of steps, skirting, dado etc. using 20 to 25mm thick slabs laid and jointed with grey cement slurry mixed with a admixture of pigment to match shade of slab including rubbing and polishing to smooth mirror finish all to required sizes, the size and design / pattern of slabs shall be as directed, including borders, margins in two or more shades of slabs over backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed.

Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces, ceiling surfaces etc including raking out joints, hacking for key scrubbing down with water etc and removing rubbish to a distance exceeding 1.50 KM but not exceeding 5.0 KM complete all as specified and as directed.

M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 10 mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4, including mixing water proofing compound as per manufacturers instructions and finishing the top surface even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Supply only Liquid water proofing compound [ISI marked] of approved make.

M & L for preparing newly plastered wall surfaces by using vaccume based sanding machine and applying two coats of Acrylic washable Distemper by using auto roller/airless sprayer, over a coat of alkali resistant primer over two or more coats of Cement based Wall Care Putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface complete all as specified and as directed. Note:- The contractor shall carryout Distempering & allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering & allied works through their authorised applicators before commencement of the work to GE for approval.

M & L for Complete removal of existing treatment of any description on wall surfaces by using vaccume based sanding machine, removal of nails and applying upto 1mm thick Cement based Wall Care Putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Acrylic Washable Distemper by using auto roller/ airless sprayer over one of alkali resistant primer on wall surfaces complete all as specified and as directed. Note:- The contractor shall carryout Distempering & allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering & allied works through their authorised applicators before commencement of the work to GE for approval.

M & L for washing, rubbing down and stopping of distempered and painted surfaces of walls / ceiling and applying one coat of Acrylic Washable Distemper by using auto roller/ airless sprayer complete all as specified and as directed. Note:- The contractor shall carryout Distempering works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering & allied works through their authorised applicators before commencement of the work to GE for approval.

M & L for Complete removal of existing treatment of any description on walls/ ceiling, pillasters, bands, borders, soffits of chajjas and projections by using vaccume based sanding machine, removal of nails including rubbing with sand paper to obtain a smooth surfaces and applying Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] by using auto roller/ airless sprayer over a Coat of Exterior Primer over 3 mm thick Cement based Wall Care Putty [primer and putty shall be of same manufacturer as that of exterior emulsion paint] by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty complete all as specified and as directed. Note:- The contractor shall carryout Weather proof Exterior Emulsion Painting under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Weather proof Exterior Emulsion Painting through their authorised applicators before commencement of the work to GE for approval.

M & L for One coat of Weather Proof Exterior Emulsion Paint [100% Acrylic] by using auto roller/ airless sprayer on old painted Walls/ ceilings, pillasters, bands, borders, soffits of chajjas and projections including necessary preparation of surfaces by using vaccume based sanding machine complete all as specified and as directed. Notes:- (a) The contractor shall carryout Weather proof Exterior Emulsion Painting under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Weather proof Exterior Emulsion Painting through their authorised applicators before commencement of the work to GE for approval.

M & L for Complete removal of existing treatment of any description on wall/Ceiling surfaces including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of cement based paint over one of alkali resistant primer on Wall surfaces complete all as specified and as directed. Note:- The contractor shall carryout Cement based Painting under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Cement based Painting through their authorised applicators before commencement of the work to GE for approval.

M & L for Two coats of Cement Based paint over a coat of Alkali Resistant Primer by using auto roller/ airless sprayer on newly plastered Walls/ ceilings, pillasters, bands, borders, soffits of chajjas and projections including necessary preparation of surfaces by using vaccume based sanding machine complete all as specified and as directed. Note:- The contractor shall carryout Cement Babsed Painting under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Cement Based Painting through their authorised applicators before commencement of the work to GE for approval.

M & L for One coat of Cement Based paint by using auto roller/ airless sprayer on old painted Walls/ ceilings, pillasters, bands, borders, soffits of chajjas and projections including necessary preparation of surfaces by washing,rubbing down and stopping complete all as specified and as directed. Note:- The contractor shall carryout Cement Babsed Painting under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Cement Based Painting through their authorised applicators before commencement of the work to GE for approval.

Cleaning of existing Covered Drains / Open Drains of any cross section in any condition [including foul condition] by removing Silt, Grit, Mud, Debris, Sludge deposits, Pebbles, Large Stones of any shape including bailing out of water by mechanical pump if required and deposited to a distance exceeding 1.5 KM but not exceeding 5.00KM for smooth flow of water complete all as specified and directed.

M & L for preparing newly plastered wall surfaces and applying three coats of white washing complete all as specified and as directed.

M & L for preparing newly plastered ceiling surfaces and applying three coats of white washing complete all as specified and as directed.

M & L for One coat of white wash on old decorated surfaces of wall including necessary preparation by brooming down or steel wire brushing complete all as specified and as directed.

M & L for One coat of white wash on old decorated surfaces of ceiling including necessary preparation by brooming down or steel wire brushing complete all as specified and as directed.

M & L for two coats of white wash on old decorated surfaces of wall etc including necessary preparation by brooming down or steel wire brushing complete all as specified and as directed.

M & L for two coats of white wash on old decorated surfaces of ceiling etc including necessary preparation by brooming down or steel wire brushing complete all as specified and as directed.

M & L for two coats of synthetic enamel paint over one coat of pink primer to newly untreated wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for One coat of synthetic enamel paint on old painted wooden surfaces of any description not other wise described over 10 cm width or girth incuding necessary preparation of surfaces complete all as specified and directed.

M & L for Two coats of synthetic enamel paint on old painted wooden surfaces of any description not other wise described over 10 cm width or girth incuding necessary preparation of surfaces complete all as specified and directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

S & F in repairs 16mm outer dia of pipe, 3–layer PP–R Polypropylene random copolymer] concealed pipes of SDR 7.4 [PN–16] UV stabilised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings complete to walls, ceilings or in floors etc. including testing complete all as specified and as directed.

S & F in repairs 20mm outer dia of pipe, 3–layer PP–R Polypropylene random copolymer] concealed pipes of SDR 7.4 [PN–16] UV stabilised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings complete to walls, ceilings or in floors etc. including testing complete all as specified and as directed.

S & F PP-R Gate Valves [Brass Insert] suitable for 20mm outer dia complete all as specified and as directed.

M & L for Making connection of PP-R distribution branch with PP-R main of size 20 / 25mm by providing and fixing tee including cutting and making fusion joint etc. complete all as specified and as directed.

S & F PVC Connection of 15mm Bore and 450mm long with PTMT check nut and union etc. complete all as specified and as directed.

S & F in repairs PVC Connection of 15mm Bore and 600mm long with PTMT check nut and union etc. complete all as specified and as directed.

Taking down Eaves Gutters /SWR Pipes [any size or pattern], including all fittings, heads, shoes, bends, swan-necks, etc. from any height complete all as specified and as directed.

S & F 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints,laid in trenches or in floors including necessary brackets, clamps as in rain water down pipes including taking up / down unserviceable / cracked rain water pipes including taking out joints of any type complete all as specified and as directed.

S & F 50mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints,laid in trenches or in floors including necessary brackets, clamps as in rain water down pipes including taking up / down unserviceable / cracked rain water pipes including taking out joints of any type complete all as specified and as directed.

S & F 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps as in rain water down pipes including taking up / down unserviceable / cracked cast iron pipes 75mm dia including taking out joints of any type complete all as specified and as directed.

S & F 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints,laid in trenches or in floors including necessary brackets, clamps as in rain water down pipes including taking up / down unserviceable / cracked rain water pipes including taking out joints of any type complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal with access door including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal with access door including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Bends of any radius with Access Door including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Bends of any radius with Access Door including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed.

S & F 100mm bore PVC [SWR] Multi Floor Trap with grating including jointing with solvent cement complete all as specified and as directed.

S & F in repairs 125mm size Stainless Steel grating for Floor Traps complete all as specified and as directed.

S & F Rotational Moulded Polythene [HDPE] Water Tanks, Double Layered, ISI Marked, Cylindrical & Vertical Type 1000 Litres Capacity hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes including dismantling and taking out existing unserviceable PVC tanks of any description and capacity complete all as specified and as directed.

S & F in repairs Ball Valves, 20 mm Bore, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe etc complete all as specified and as directed.

S & F in repairs Bib Taps, 15 mm dia, Brass Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as specified and as directed.

S & F in repairs Bib Taps, 15 mm dia, Long Body, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as specified and as directed.

S & F in repairs Two way Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as per Jaquar Catalogue No. KUP-35041PM or its equivalent in Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F in repairs, Brass Chromium Plated Shower Rose of size 125mm with or with out swivel joints fixing to steel pipes complete all as specified and as directed.

S & F in repairs Angle Cock, 15 mm dia, cast copper alloy with capstan head, Chromium Plated, screwed down high pressure with crutch or butterfly handle for iron pipe etc. complete all as per Jaquar Catalogue No. CON-053 or its equivalent in Kohler / Cera / Parryware / Grohe / Crabtree complete all as specified

S & F in repars Stop Valves, 15 mm dia, cast copper alloy with capstan head, Chromium Plated, Fancy Type, screwed down high pressure with crutch or butterfly handle with long shank and cup [concealed type] for iron pipe etc complete all as specified and as directed.

S & F in repairs Stop Valves, 15 mm bore dia of pipe, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions etc complete all as specified and as directed.

S & F in repairs Pillar Taps, cast copper alloy, Chromium Plated, Fancy Type, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.

S & F in repairs Health Faucet with 1 m long flexible tube, wall hook, non return valve complete as per Jaquar Catalogue No. ALD-563 or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F in repairs Stainless Steel, Soap Dish, Fancy Type complete all as per Jaquar Catalogue No. AQN-7731 or its equivalent in Kohler / Cera / Parryware / Grohe / Crabtree complete all as specified.

S & F in repairs Brass CP Towel ring complete all as specified and as directed.

S & F in repairs Stainless Steel Toilet Paper Holder, Chromium plated, Fancy type complete all as per Jaquar Catalogue No. ACN-1153N or its equivalent in Kohler / Cera / Parryware / Grohe / Crabtree complete all as specified.

S & F in repairs PVC Body Cabinet Box Mirror of size 350mm X 450mm X 100mm in PTMT alloy of approved design and pattern complete all as specified and directed of Make: Supreme / National / Alphina / Prayag

S & F in repairs Corner Glass Shelf with Bracket complete as per Jaquar Catalogue No. ACN-1173 or its equivalent in Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F in repairs Vitreous China Wash Down Water Closet [Pedestal pattern], White, of size 560 x 440 X 395 mm including flush pipe of polyethylene of low or high density of PVC, 32mm dia, PVC Connection of 15mm Bore and 600mm long with PTMT check nut and union etc. including brackets and connections to pipe and flush pipe including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap including taking down of existing unserviceable water closet complete all as specified and as directed.

S & F in repairs Vitreous China Squatting Pan "Orissa Pattern", White of size 580 mm X 440 mm with integral foot rests and 'P' or 'S' Trap including provision of lime concrete bedding , flush pipe of polyethylene of low or high density of PVC, 32mm dia, PVC Connection of 40mm Bore and 750mm long with PTMT check nut and union etc. including brackets and connections to pipe complete all as specified and as directed.

S & in repairs F Vitreous China Ware Wash Hand Basin, White, Flat Back of size 550 mm X 400 mm including brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe, PVC Connection of PTMT complete all as specified and as directed.

S & F in repairs 10 Litres capacity, PVC Valve less, Syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle including brackets and connections to pipe and flush pipe complete all as specified and as directed.

Taking down carefully copper / aluminium point wiring [light, fan, socket or power] complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and making good the disturbed surfaces all as per existing complete all as specified and as directed.

Taking down carefully submain wiring of any description and size complete including wooden battens / conduits / casing capping and making good the disturbed surfaces all as per existing complete all as specified and as directed.

Taking down MCCB DBs, MCB DBs, SPN / TPN Enclosures including MCCBs, MCBs etc of any description and any capacity and making good the disturbed surfaces all as per existing complete all as specified and as directed.

M & L for Point Wiring complete with 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, Two runs, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, conforming to IS - 694 drawn through and including heavy duty PVC Conduit, 20 mm dia including all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type and Metal GI Flush Box of suitable size and thickness including Modular type Base / Grid Frame & Cover Frame for housing Modular Type Switches, Sockets and Regulators etc. concealed in walls, including 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable as earth continuity conductor with colour coding and connecting to Earth Dolly for One Light / Fan Point / Bell Point complete all as specified and as directed.

All as per Serial Item No. 141 above but one 3 Pin Socket Outlet 6 Amps on independent board, complete all as specified.

All as per Serial Item No. 141 above but One 3 Pin Socket Outlet 6 Amps on same Board complete all as specified.

All as per Serial Item No. 141 above but one 3 Pin Socket Outlet 16 Amps power point on independent board, with 1100 Volts, FRLS grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable confirming to IS - 694 and including 1100 Volts, FRLS grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable as Earth Continuity Conductor.

S & F Switch, Modular Type, One Module, Single Pole, One Way, 6 Amps, 230 Volts complete all as specified and as directed.

S & F Switch Modular type, one module, Single pole, one way, 16 Amps, 230 Volts complete all as specified and as directed.

S & F Socket Outlet, 3 pin, 16 Amps cum 3 pin 6 Amps, Modular Type, Two Modules, Multipurpose, 230 Volts complete all as specified and as directed.

S & F Socket Outlet, 3 Pin, 6 Amps, Modular Type, Two Modules, 230 Volts, complete all as specified and as directed.

S & F Ceiling Rose, PVC Body, Three Terminals, 230 Volts complete all as specified and as directed.

M & L for Sub main wiring with 2 runs of single core 2.5 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 20 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor complete all as per existing complete all as specified and as directed. Note: 3 runs of 2.5 Sq.mm & one run of 20 mm dia PVC Conduit will be measured as one unit.

S & F MCB DB, SPN, 12 Way, 240 Volts, with DIN Channel, Double Door with 100 Amps rated bus bar suitable for mounting MCBs flush mounted with wall complete all as specified and as directed.

S & F MCB DB, SPN, 8 Way, 240 Volts, with DIN Channel, Double Door with 100 Amps rated bus bar suitable for mounting MCBs flush mounted with wall complete all as specified and as directed.

S & F MCB, SPN, 40 to 63 Amps, 10 KA, C Curve, AC, 230 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, SP, 6 to 32 Amps, 10 KA, C Curve, AC, 240 Volts, 50 Hz complete all as specified and as directed.

S & F in repairs Surface & wall mounted Energy efficient LED Tube Light Fitting, of not less than 1000 Lumens output, 5700 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F in repairs Surface & wall mounted Energy efficient LED Tube Light Fitting, of not less than 2000 Lumens output, 5700 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Square recessed mounted Flat Panel 36 Watt 2' x 2' LED Ceiling Light suitable for fixing in False Ceiling, not less than 3600 Lumens output,, 6500 K, with high transmitive diffuser for soft-light and glare free symmetrical illumination with all accessories internally prewired and including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm including taking down existing light fittings of any description and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

Supplying, laying and testing XLPE insulated and PVC sheathed, FRLS, armoured heavy duty underground cable, ISI marked with stranded aluminium conductor 1100 Volt grade of size 4 Core, 25 Sq.mm cross section suitable for earthed system, laid in floor / duct or fixed to poles / walls or drawn through pipes / sleeving through pipe in duct, including suitable size Double compression copper stainless steel cable gland, crimping type cable lugs, sockets etc. complete all as specified and as directed.

Supplying and laying GI pipe, 40mm dia, Light grade for cable protection at road crossing etc. or fixing on wall / poles of any type, secured with clamps complete all as specified and as directed.

CHAMUNDESWARI ENTERPRISES

M/S SRI VENKATA BHAVANI CONSTRUCTIONS

P SRINIVASA RAO

G Srinivas Rao

CIVILEC ENGINEERING WORKS