Construction Work of Sub Division-II Office at Dhampur Under Eastern Ganga Canal Construction Division-6, Najibabad District Bijnor

Amount

Earth work in Foundation in dry soil (Loam clay or sand) including lift up to 1.5 M and lead up to 30 m and including back filling, watering and ramming of excavated earth into the plinth with removal and disposal of surplus earth as directed by the Engineer-in-charge up to distance of 30 M from the foundation trenches.

Cement Concrete with 4 Cm guage approved stone ballast coarse sand and cement in propotion of 1:2:4 including supply of all materials, labour and T&P etc. required for proper completion of work

M-150 brick work in 1:4 (one cement and four coarse sand of 1.75~2.20 F.M. mortar) in foundation and plinth including supply of all materials, labour and T&P etc. required for proper completion of work

RCC Work with Cement approved coarse sand and 2cm, gauge approved stone grit in proportion of 1:1.50:3 in Plinth Beam in Foundation excluding supply of reinforcement and its bending but including its fixing and binding the same with BWGGI Binding wire and including necessary centering ans shuttering etc. and supply of all materials, labour and T&P etc. complete required for proper completion of work. Binding wire of supplied by the contractor free of cost.

40 mm thick damp proof coarse of cement concrete consisting of 1 part cement and 2 parts of approved course sand and 4 parts approved 13mm approved graded stone grit and including water proofing material as ordered by the Engineer-in-charge in the proportion as specified by the manufacturer including supply of all materials, labour and T&P etc. required for proper completion of the work and including proper curing and shuttering as necessary.

Painting on D.P.C. with two coats of air blown bitumin 80/50 or 85/25 @ about 1.7 kg per sq. meter including cost of fuel if any.

M-150 brick work in 1:4 (one cement and four coarse sand of 1.75~2.20 F.M. mortar) in superstructure and plinth including supply of all materials, labour and T&P etc. required for proper completion of work

M-150 brick work in 1:4 (one cement and four coarse sand of 1.75~2.20 F.M. mortar) in superstructure in 1/2 brick thick wall including supply of all materials, labour and T&P etc. required for proper completion of work

Sand filling in plinth including supply of necessary quantity of sand from a distance not exceeding 8 Km. From the site of work and including watering, dressing etc. Rate to include cost of all materials labour T&P etc. required for proper completion of work.

Cement Concrete under vitrefied tiles with 4 Cm guage approved stone ballast coarse sand and cement in propotion of 1:4:8 including supply of all materials, labour and T&P etc. required for proper completion of work

RCC Work with Cement approved coarse sand and 2cm, gauge approved stone grit in proportion of 1:1.50:3 in lintels of doors, windows and sunshades excluding supply of reinforcement and its bending but including its fixing and binding the same with BWGGI Binding wire and including necessary centering ans shuttering etc. and supply of all materials, labour and T&P etc. required for proper completion of work. Binding wire of supplied by the contractor free of cost.

RCC Work with Cement approved coarse sand and 2cm, gauge approved stone grit in proportion of 1:1.50:3 in T-beam, Slab, Roof and RCC Column excluding supply of reinforcement and its bending but including its fixing and binding the same with BWGGI Binding wire and including necessary centering ans shuttering etc. and supply of all materials, labour and T&P etc. required for proper completion of work. Binding wire of supplied by the contractor free of cost.

Mild Steel or Iron in plain work such as reinforced concrete or reinforced brick work (When not included in an over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of all steel

20 mm thick rough cast exterior cement plaster on walls consisting 10 mm thick backing cast of 1:3 cement mortar (1 cement 3 course sand) and 10 mm thick finishing coat of 1:3 cement mortar (1 cement 3 coarse agreegate of size 6mm to 12 mm) including arises, chamfers and/or rounded angles not exceeding 80 mm

12 mm thick plaster with one part of cement and two parts of approved coarse sand including cost of all material, Labour, T&P etc Complete.

Supply and laying of vitrified floor tiles (Bell/Kajaria/Somani or Other Standard Make) in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS:15622 of approved make in all colors and shades, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse Sand) including grouting the joints with white cement and matching pigments etc, complete (Size of Tile 60 X 60 CM)

Supplying and fixing 6 mm thick china glazed tiles of first quality in skirting or dado laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry jointing and polishing complete including supply of all materials, labour and T&P etc. required for proper completion of the work.

Providing Wall Putty on New Surface with approved quality material of berger/JK/Birla or Similar Make 2 Coates i/c all cost of materials labour and T&P etc complete.

Finishing Walls with acrylic smooth exterior paint of required shade (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Distempring 2 coat with oil bound distemper of approved brand and manufacture and required shade on undecorated wall surface to with an even shade over and including a primer coat with cement primer of approved brand and manufacture such as British, Shalimar, Asian paint after throughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand prepared smooth including cost of all materials.

Mild steel or iron work of small size and sections such as holdding down bolts, hold fast, tie roads,gratings etc.(when not included in an over all rates)wrought to required from ,including of supply of steel, boalts nuts and wastage etc. and there fix

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement:3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing Brick Coba 12 mm thick laid with M-150 Class Brick bat coba 7.50 cm thick with gap of 15 mm to each other, over 20 mm thick base of cement mortar 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with aerelic cement concrete water proofing compound fitted gaps of coba & top of coba mortar mixed with water proofing compound in 1:4 cement and coarse sand mortar finished smooth & top mashed false square 30 cm x cm and side wall parapet shall be monotythic plaster wall upto 30 cm higher and juction and corner shall be rounded by brick ballast cement and coarse sand masonary coba with top finished palster mixed with acetic water proofing compound @ 2% by weight & including S/o all material labour , T&P etc complete for proper completion of work

Providing wood work in frame of door, window, clerestory windows and other frames wrought framed and fixed in position (Teak Wood)

Supply and fixing of flush doors commercial quality conforming to IS 2202 Part-I (1983) including fixing of Wooden Cleats and Stopped and including fixing and adjustment of hinges bolts locks handles springs filling with necessary screws to be supplied (35 mm thick)

Providing and fixing 25 mm thick shutters for glazed shutters in windows by teak wood inlcuding ISI marked anodised aluminium butt hinges with necessary screws

Providing and fixing 30 mm thick wire gauze shutters using galvanised M.S. Wire Gauze of average width of aperture 1.4 mm with wire of dia 0.63 mm for doors, windows and clerestory windows including ISI marked bright finished or/and black enamelled M.S.B

Fixing panes of glass with equal or equivalent I.S.I. marked quality putty, brads and springs and including supply of all materials and labour etc complete

Applying primer coat over new wood work including cost of all and supply of materials labour and T&P etc. required for proper completion of the work.

Applying primer coat over new steel and other metal surface before paint including preparing the surface by throughly cleaning oil hrease dirt and other foreign matter and scoured with wire brushes fine steel/wood scrappers sand paparing and knotting including coat of all and supply of all materials labour and T&P etc required for proper completion of the work.

Painting first coat over priming coat (but excluding cost of priming coat) on wood or steel and other metal surface with superior synthetic enamel paint of standard make brushing to give an even shade and finished and including cleaning the surface all dirt dust and other foreign matter sand paparing and stripping including cost matter and scoured with wire brushes fine steel/wood scrappers sand paparing and knotting including coat of all and supply of all materials, labour and T&P etc. required for proper completion of work

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI: 12701 marked with cover and suitable locking arrangement and making necessary holes for inlets, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing water closet squatting pan (Indian type W.C. Pan with 100 mm sand cast iron P or Strap, 10 litre low level white PVC Flusing Cistern with manually controlled device (Handle Level) Conforming to IS 7231 with all fittings and fix. (White Vitreous China Orissa Pattern WC Pan of Size 580x440 mm with integral type foot rests) i/c all material, labour T&P etc complete.

Providing and fixing white vitreous china European type Water closet (European Type) with seal and lid, 10 lt low level white vitreous china flusing cistern & CP flush bend with fittings & CI brackets, 40 mm flush bend, overflow arrangement with SP (WC Pan with ISI marked white soild plastic seat and lid) i/c all material, labour T&P etc complete.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x2260x350 mm and 350x410x265 mm sizes respectively with 5 litre white PVC automatic flusing cistern with standard flush pipe and CP brass spreaders with brass unions i/c all material, labour T&P etc complete.

Providing and fixing white vitreous china wash basin of size 630x450 mm with a pair of 15mm CP brass Pillar taps including making all connections but excluding the cost of fittings

Providing and fixing PVC Waste pipe for sink or wash basin including PVC Waste Fittings Complete (32 mm dia Flexible pipe)

Providing and fixing 600X450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washer complete

Providing and fixing toilet paper holder CP brass with cost of all material labour T&P ctc.

Providing and fixing Stainless steel kitchen sink - with drain board bowl depth 250 mm drain board size 610x510mm bowl depth 200mm with C.I. brackets and stainless steel plug 40mm i/c painting of fitting and brackets cutting and making good the wall.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing and fixing G.I. pipe complete with G.I fitting and clamps i/c cutting chase and making good the wall etc i/c all materials labour T&P etc complete. 15mm nominal bore bath room inner side

20mm nominal bore bath room outer side

Providing laying and jointing glazed stoneware pipes grade-A with stiff mixture of cement mortar in the of 1:1 (1 Cement: 1 Fine Sand) including testing of joint etc complete

Providing and fixing 15mm dia C.P.Brass stop cock of standard design and approved make i/c all materials labour T&P etc complete.

Providing and fixing 15mm dia long nose C.P. brass bib cock of approved quality including all material, labour T&P etc.

Providing and fixing 15mm dia C.P. brass angle valve for basin mixer geyser point of approved quality including all material, labour T&P etc.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing soil, waste and vent pipes :100 mm dia Sand Cast Iron S&S Pipe as per IS:1729

Providing and fixing plain bend of required degree for 100 mm dia pipe

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete for 100x100x100 mm

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter 100 mm

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 10 mm outlet

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 100 mm dia

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 50 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing uplasticised PVC connection pipe with brass unions :30 cm lenght and 15 mm nominal bore

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Group C)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required 3 x 1.5 sq. mm

3 x 2.5 sq. mm

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

2 way 5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Bell push

Stepped type Modular Fan regulator (2 module)

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single Pole

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 A, 16 KA, TPMCCB

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Supplying and fixing following electric items including cost of all materials. Labour T&P etc. all work completes.

Wiring for circuit/submain wiring alongwith earth wire with 2x16 sqmm + 1x6 sq. Mm earth wire of FRLS PVC insulated copper conducter, single core cable in surface/recessed steel conduit as required.

Supplying chemical emulsion in sealed containers including delivery as specified:Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:

Treatment of existing masonry using chemical emulsion @one litre per hole at 300 mm interval including drilling holes at45 degree and plugging them with cement mortar 1:2 (1 cement: 2 coarse sand) to the full depth of the hole

Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same.

M/S VIPIN KUMAR CONTRACTOR

M/s KS Construction

NARENDRA KUMAR