T.No.-EDC(USN)24/2024-25

Amount

Annexure-A (LABOUR CHARGES)

Laying of Barbed Wire as per instruction of Engineer in charge

Earthing of distribution transformer including digging of pit of size 2.5 Mtr depth and make hole of size 150 mm. Placing of earthing electrode, connecting the same with G.I. Strip (to be supplied by contractor) of size 35x6 mm for a minimum lenght 6 m. treatment of soil with highly condctive substance as per IS 30343 complete in all respect, result of earthing resistance to be recroded in M.B. before and after installation of earthing. The earth resistance after earthing should be less than 1 Ohm.

Fabrication of MS Channel angle iron etc in required sizes with drilling of holes upto good finish for top channel, bracing and special type bracket etc. as per RESPO schedule and local approced drawing.

Excavation of earth for stay pit of size 0.6x0.6x1.2 mtr in all types of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and disposal of surplus excavated soil as directed complete work.

Fixing, tightening and nozzling of stay with pole and stay rod on required tension as per drawing/manual in 11 KV Line.

Excavation of earth for pole pit of size 0.9x0.6x1/6 of full length of pole for erection of pole in all types of soil including proper dressing of sides and ramming of bottom including etting out the excavated soil and disposal of surplus excavated soil as directed complete work.

Erection of SP-55 single support pole in proper level and alignment along with fixing of all accessories like top channel & clamps a s per RESPO manual.

Erection of Sp-55 double support pole in proper level and alignment along with fixing of all accessories like top channel,X bracings & clamps as per RESPO manual.

Muffing of poles size 0.45x0.60 cm radius with 1:3:6(1 cement:3 coarse sand :graded stone 10 mm nominal size) block size 45 cm height from ground level including cost of cement, stone and sand etc.

Dismantling of existing HT line including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(ACSR Dog).

Painting of SP-55 pole with angle and channel and all steel part by one coat of Red Oxide Primer and two coats of aluminium Paint and two strip of fluorescent altemate Red and White paint 30 Cm wide upto 1.5 Mtrs. From ground level.

Route cleareance by cutting of tree branches / proning, loping and chopping of trees for L.T., 11 & 33 KV line.

T-off Connection Complete 11 KV line

Cartage of ST pole SP-55 Poles from store centre to construction site with loading, unloading at both points and proper stacking.(Distance 21-50 Km)

Cartage of other material (other than poles) by vehicle from Store Center to nearest construction site Store including loading and unloading at both ends(distance 21-50 Km)

Headload cartage of SP-55 Pole from road to site(distance 0-1 Km)

Headload cartage of small material(distance 0-1 Km)

Straightning of Tilted STP Poles

Laying G.S. Earth wire 7/16 SWG for providing Earth Wire on 11 KV Line.

Back Carriage of Petty material, 0-20 Km

Fixing of IPC with AL. Bail for Earthing.

Removing Heavy Tree Branches from line.

Fixing of 11 KV 90KN Tension Clamp B&IPC

Fixing of 11 KV Suspension Ties.

Fixing of 11 KV IPC for CC to CC Conductor.

Fixing of 11 KV IPC for CC to Bare Conductor.

Fixing of 11 KV Mid Span Jointing Kit.

Opening of 11 KV Jumper and Making again of section pole

Fixing, tightening and nozzeling of stay with pole and stay set on required tension

Grouting of Stay in size 0.6x0.6x0.3 in CC ratio 1:4:8 (1 cement : 4 graded stone 20mm nominal size : 8 coarse sand) block including cost of Cement, sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, leveling as per RESSPO Manual.

Laying Spreading, Stringing AAAC Conductor.

Annexure-B (SUPPLY ITEMS)

Supply of MS NUT & BOLT Off size

Supply of Holding Clamp for SP-55 with N/B

Supply of F-Clamp

Supply of Earth wire Clamp for SP-55 with N&B

Supply of Stay Clamp for SP-55 with Nut & Bolt

Supply of 11 KV Cable Ties for Pin Insulator

Supply of 11 KV IPC for Covered to Covered Conductor.

Supply of 11 KV IPC for Covered to Bare Conductor.

Supply of 11 KV mid span Jointing Kit

Supply of IPC with Al. BAIL for Earthing 11 KV

Supply of 11 KV AAAC Covered Conductor AL-59, 99 Sq.mm.

Supply of Al.Lug 120 Sq.mm

Supply of Barbed Wire

Supply of ACE Chemrod DIA60MM Length 3000MM

Supply of Fluid Compound for Chemical Earthing Rod.

Supply of 11 KV Tension Clamp with BAIL & IPC

PERFECT ELECTRICALS AND ENGINEERS (BID ID -337392)

M/S AGARWAL CONSTRUCTIONS (BID ID -338636)