Renovation and Beautification of Park near HKB Barrage to make it as Tourism Hub CM Announcement Code 9917 dated 06.04.2015.

Amount

Earth work in excavation in foundations, trenches, etc.in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directe within all lead and lift.

Rehandling LEAD UPTO 15 METER.

Gravel (in loose form in non-cohesive binding material) work in excavationwith occasional use of picks, exclusive of compensation of earth, undressed with a combined lead upto 495 metres, with percentage of gravel or kankar

First class brickwork laid in cement sand mortar 1:4 in foundation and plinth.

First class brickwork laid in cement sand mortar 1:4 in first storey up to 4 meters above plinth level.

Pebble dash exterior plaster on walls with a mixture of washed pebble or crushed stone graded from 6 mm to 12 mmm nominal size dashed over and including fresh cement plaster in 2 coats, first coat 10 mm thick cement plaster 1:4, (1 cement, 4 sand) and finishing coat 10 mm cement plaster 1:3, mixed with 10% finely ground hydrated lime by volume of cement including arises, chamfers and/or rounded angles not exceeding 80 mm in grith.

Centring and shuttering with steel shuttering for slab culverts excluding 3 metre but.

Shuttering for faces of concrete with steel shuttering for faces of concrete foundations and foundation beams (vertical or battering) etc.

Shuttering for reinforced cement concrete conical type roofing complete in all respects.

Centring and shuttering with steel shuttering for faces of walls, partitions, retaining walls,well steining and the like (vertical or battering)including attached pilasters etc.

Shuttering for sides and soffits hunchings, girder bressumers and lintels.

Centring and shuttering with steel Shuttering for for sides and soffits hunchings, girder bressumers and lintels. Above 4 meter Upto 6 meter roof beam B1.

Centring and shuttering with steel Shuttering for for sides and soffits hunchings, girder bressumers and lintels. Above 8 meter Upto 10 meter roof beam B101.

Centring and shuttering with steel Shuttering for for sides and soffits hunchings, girder bressumers and lintels. Above 10 meter Upto 12 meter roof beam B201.

Centring and shuttering For columns square or rectangular.

Centring and shuttering for circular column

Centring and shuttering for circular column upto 4 Meter

Centring and shuttering for circular column above 4 meter Upto 6 Meter

Centring and shuttering for circular column above 6 meter Upto 8 Meter

Centring and shuttering for circular column above 8 meter Upto 10 Meter

Centring and shuttering for circular column above 10 meter Upto 12 Meter

Centring and shuttering with steel shuttering for slab culverts excluding 3 metre but.

Cement concrete 1:4:8 with stone aggregate 40 mm nominal size in foundation and plinth.

Cement Concrete 1: 1 ½: 3 with stone aggregate 20mm nominal size in foundation and plinth.

Design mix cement concrete of grade M-10 with minimum cement contents 220 Kg./cum in foundation and plinth.

Design mix cement concrete of grade M-25 with minimum cement contents 330 Kg./cum in foundation and plinth.

Design mix cement concrete of grade M-35 with minimum cement contents 350 Kg./cum in foundation and plinth.

Design mix cement concrete of grade M-25 with minimum cement contents 330 Kg./cum in first storey upto 4 meters above plinth level.

Design mix cement concrete of grade M-25 with minimum cement contents 330 Kg./cum Above 4 meter upto 6 meter above plinth level.

Design mix cement concrete of grade M-25 with minimum cement contents 330 Kg./cum Above 6 meter upto 8 meter above plinth level.

Design mix cement concrete of grade M-25 with minimum cement contents 330 Kg./cum Above 8 meter upto 10 meter above plinth level.

Design mix cement concrete of grade M-25 with minimum cement contents 330 Kg./cum Above 10 meter upto 12 meter above plinth level.

Design mix cement concrete of grade M-25 with minimum cement contents 330 Kg./cum Above 12 meter upto 14 meter above plinth level.

Precast cement concrete 1:2:4 with stone aggregate 20 mm nominal size in Kerbs and the like items, finished smooth with 6 mm thick cement plaster 1:3 on exposed surface including from work, placing and fixing in position, complete at the ground level or in first storey.

Squared rubble masonry coursed (coursed rubble) in foundation and plinth in cement mortar 1:4, Cooping on top cement concrete 1:2:4 with stone aggregate 20 mm nominal size in first storey upto 4 meter above plinth level

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coasts of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc.

Steel ReinforcementTMT bars Fe 500 EQR IFC 500D grade or more for RCC works, where not including in the complete rate of R.C.C. including bending , bindding and place in poition complete.

12 mm thick cement plaster 1:4

preparation of plastered surfaces for distempring including sand papering the surface, applying filling with approved quality filler,consisting of plaster of paris and chalk mitti including the surface to the required finish complete.

Preparation of plastred for oil bound distemper the surface appliying one coat of linseed oil & filling with approved quailty fillup consisting of white lead linseed varnish and chalk mitti i/c finishing the surface to the requried finish compleate.

Distempring with wasable oil bound distemper.

Precast chequered tiles of 20 mm thickness in ordinary grey cement without chips laid on 20 mm thick bed of cement coarse sand mortar 1:3 with neat cement slurry between joints and over the base in floors, treads of steps and landings.(colour chequered tiles in flooring are used).

Providing & fixing of Dholpur stone tiles 25 mm thick in wall facing (lining) laid in any pattern as specified on 12 mm thick cement coarse sand mortar 1:3 and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and labour for fixing cramps, pins and dowles etc.

Extra for nosing in treads of steps of Kotah stone slab

Providing and fixing of Kotah stone 20 mm thick in skirting risers of steps, dados and wall facing (lining) and pillars laid on 12 mm thick cement coarse sand plaster 1:3 laid and jointed with neat cement slurry, mixed with pigment to match the shade of stone including rubbing and polishing including labour for fixing cramps, dowels and pins etc.

Providing and fixing vitrified tiles of Size 600*600 mm of approved make in flooring laid in any pattern as specfied over base of 20 mm thick cemnet coarse sand mortar 1:3 and jointed with white slurry mixed ewith pigment to match the shade to tiles.

Pvdg & fixing Cermic tiles/anti skid tiles of size 400 mm × 400 mm or above size of approved make in flooring, laid in any pattern a specfied over base of 20 mm thick cement coarser sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles Note;- Tiles shall be of premium qulaity (first quality ) of reupted manufacture like NITCO KAJA-RIA, SOMANI, ORIENT & JOHNSONS and RAK.

Provding & fixing ist quality ceramic glazed wall tiles confirming to IS 15622 (thickness to be specified by manufacture) of approved make in all colours, shades expect burgundy, bottle green, black of any size as approved by Enginner in charge in skirting, riser of steps and dados over 12 mm thick bed of cement mortar 1:3 and jointed with grey cement slurry, including pointing in white mixed with pigment of matching shades complete. size of ceramic Glazed tiles 300×450 mm.

Supply, lying and fixing MOSAIC anti skid tiles of any size of approved make in flooring laid in any pattern as specified over a base of 20 mm thick cement coarse sand mortal 1:3 and jointed with white slurry mixed with pigment to match the shade of tiles.

Supply, lying and fixing MOSAIC anti skid tiles of any size of approved make in skirting laid in pattern as specified over a base of 12 mm thick cement coarse sand mortal 1:3 and jointed with white slurry mixed with pigment to match the shade of tiles.

Kotah stone 20 mm thick in skirting risers ofsteps, dados and wall facing (lining) and pillars laid on 12 mm thick cement coarse sand plaster 1:3 laid and jointed with neat cement slurry, mixed with pigment to match the shade of stone including rubbing and polishing including labour for fixing cramps,dowels and pins etc.

LAYING AND FIXING GRANITE STONES IN ALL SHADES 15 MM TO 18 MM THICK IN FLOORING, LAID IN ANY PATTERN AS SPECIFIED OVER BASE OF 20 MM THICK CEMENT COARSE SAND MORTAR 1:3 AND JOINTED WITH WHITE CEMENT SLURRY MIXED WITH PIGMENT TO MATCH THE SHADES OF GRANITE STONES BLACK LAPTOO GRANITE FLOOR.

LAYING AND FIXING GRANITE STONES IN ALL SHADES 15 MM TO 18 MM THICK IN SKIRTING, LAID IN ANY PATTERN AS SPECIFIED OVER BASE OF 20 MM THICK CEMENT COARSE SAND MORTAR 1:3 AND JOINTED WITH WHITE CEMENT SLURRY MIXED WITH PIGMENT TO MATCH THE SHADES OF GRANITE STONES BLACK LAPTOO GRANITE FLOOR

Providing and fixing of casement and fixing windows made from muilti chambered UPVC profiles of 56 to 86mm width in natural stabilized for heat, light, impact & UV radiation The UPVC profiles should be reinforced with galvanized steel profile of designed thickness.all openable sashes shall be having weather seal filled in continuous length made from bubble epdm rubber and side hung/ top hung with upto 90 degree opening friction stays of SS 304 with provision of muiltipoint locking system made from Espagrods complete in all respect as directed by Engineer-in-charge.Frame work

Providing and fixing of casement and fixing windows made from muilti chambered UPVC profiles of 56 to 86mm width in natural stabilized for heat, light, impact & UV radiation The UPVC profiles should be reinforced with galvanized steel profile of designed thickness.all openable sashes shall be having weather seal filled in continuous length made from bubble epdm rubber and side hung/ top hung with upto 90 degree opening friction stays of SS 304 with provision of muiltipoint locking system made from Espagrods complete in all respect as directed by Engineer-in-charge. Openable shutter

Providing and fixing of casement and fixing windows made from muilti chambered UPVC profiles of 56 to 86mm width in natural stabilized for heat, light, impact & UV radiation The UPVC profiles should be reinforced with galvanized steel profile of designed thickness.all openable sashes shall be having weather seal filled in continuous length made from bubble epdm rubber and side hung/ top hung with upto 90 degree opening friction stays of SS 304 with provision of muiltipoint locking system made from Espagrods complete in all respect as directed by Engineer-in-charge. Double glass glazing

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size in foundation and plinth.

Provding And Laying 60 mm thick interloking paver blocks of all shapes and colours in design mix cement M-35 over a bed of 30 mm thick fine sand complete in all respect.

Provding And Laying 80 mm thick interloking paver blocks of all shapes and colours in design mix cement M-40 over a bed of 30 mm thick fine sand complete in all respect.

Wrought iron and mild steel (usingangles, flats, square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors open able or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position.

Prepration of subgrade including trenching, rough dressing of spoil, final, dressing of earth to given levels and camber, watering, rolling with road roller, and compected the bed

WBM SUB BASE OF GRADING- III (53-22 MM SIZE)

Providing and fixing 910mm high stainless steel railing make by Tata & JWS etc.

PROVDING AND FIXING ACP SHEETS MAKE BY FIBERE MATERIAL

Provding And Fixing a Park Equpiments, Make by the M.S pipe and Images of Equipment attached Spring Rocker (Spring Rocker iron frame 70 mm round pipe 14 Gauge, and base heavy spring fitted on 12 mm MS Flat. Seats made of Roto moulding (Powder coated)).

Provding And Fixing a Park Equpiments, Make by the M.S pipe and Images of Equipment attached Spring SEE SAW (Spring See Saw two seater iron frame 70 mm round pipe 14 Gauge, and base heavy spring fitted on 12 mm MS Flat. Seats made of Roto moulding (Powder coated)).

Provding And Fixing a Park Equpiments, Make by the M.S pipe and Images of Equipment attached DOLI FIBRE SWING (Iron frame made of 70 mm M.S Sq. Pipe 14 gauge, Columbus size 24”X42” made of FRP Thickness 6 mm, supporting of M.S Chain 8 mm (Tested) with Bush System).

CHAIR SWING (Four seater main structure made of 70 mm round pipe ‘B’ class, ball bearing system with31 mm round and single side bearing ,chain 8 mm (Tested), (Plastic coated ). Seat made of Rubber patta (Imported)).

SPRIL SLIDE (Side length 13’ made of FRP 6 to 8 mm with Platform made of 70 mm Round MS pipe ‘B’ class. Support 38 mm, MS Sq. pipe and FRP Sheet 6 mm with 5 supports 50mmX50mmX14 gauge. Ladder made of 38 mm MS sq. pipe 14 gauge.).

Provding And Fixing a Park Equpiments, Make by the M.S pipe and Images of Equipment attached FUN STATION

Providing and fixing FIBER ANIMAL SHAPE DUSTBIN (Made of FRP Thickness 4 mm)

Provding And Fixing a Boat For Jhill.

Provding And fixing Laughing Mirrors of total Size 2.55m x 14.54 m

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing

Dismantling Stone Masonry dressed stone work, ashlar face work, marble work in cement .

Dismantling cement concrete plain 1:2: 4 mix

Providing And Fixing A water Cooler

Supply and erection of miniature circuit breaker / isolator 240 /415 V in the existing distribution board including making necessary connections. Miniature circuit breakers of 9 KA breaking capacity. SP MCB of 9 KA breaking capacity 6 Amp.. to 32 Amp.

Supply and erection of miniature circuit breaker / isolator 240 /415 V in the existing distribution board including making necessary connections. Miniature circuit breakers of 9 KA breaking capacity. TPN MCB of 9 KA breaking capacity 6 Amp.. to 32 Amp..

Switch 5 amp. On existing sheet

Wall socket 5 amp. On existing sheet.

15 amp switch on existing sheet

3 pin 15 amp. Multi socket on existing sheet

Erection only of 1x40 watts or 2x40 watts 1220 mm long / 1x20 watts or 2x20 watts ,610 mm long fluorescent tube fitting directly on wall including necessary connections with 0.75 sqmm ( 24 / 0.20 mm ) PVC copper flexible cable for connecting the tube with the adjecent point.

Supply and erection of hexagonal M.S. box 1.60mm thick having each side 8 cms, 7.5 cms deep, top covered with M.S. lid by means of screws including 10 mm dia 30 cm long mild steel rod made into suitable suspension hook and erected in R.C.C. slab of erection of fan, the bottom covered with 3 mm thick bakelite sheet with suitable holes, painting etc. complete with all labour and material required to complete the job.

Bakelite sheet including fixing with brass screws and washers (5 mm thick)

Erection of ceiling fan complete with necessary earthing of fan and regulator i/c carriage from local railway station /goods transport /PWD store to the site of work.

Wiring in 1.5 Sqmm PVC insulated copper conductor cable in 1.6mm thick conduite pipe. Fan Points : Medium points

Wiring in 1.5 Sqmm PVC insulated copper conductor cable in 1.6mm thick conduite pipe. Fan Points : Long points

Wiring in 1.5 Sqmm PVC insulated copper conductor cable in 1.6mm thick conduite pipe. Light Points : Medium points

Wiring in 1.5 Sqmm PVC insulated copper conductor cable in 1.6mm thick conduite pipe. Light Points : Long points

Wiring in 1.5 Sqmm PVC insulated copper conductor cable in 1.6mm thick conduite pipe. 3 pin light plug points including earthing the 3rd pin etc; Short Point

Wiring in 1.5 Sqmm PVC insulated copper conductor cable in 1.6mm thick conduite pipe. 3 pin light plug points including earthing the 3rd pin etc; Long Point

3 pin light plug points with 4Sqmm PVC insulated copper conductor cable including earthing the 3rd pin etc. Long Point

S/E of P.V.C. copper conductor cable 1100 volts grade in pipe of suitable size excluding cost and erection of pipe: Cable Size 1.5 Sq. mm

S/E of P.V.C. copper conductor cable 1100 volts grade in pipe of suitable size excluding cost and erection of pipe: Cable Size 2.5 Sq.

S/E of P.V.C. copper conductor cable 1100 volts grade in pipe of suitable size excluding cost and erection of pipe: Cable Size 4 Sq. mm

Supply and erection of double door sheet steel enclosures distribution boards suitable for MCBs and ELCBs etc. recessed in wall including bonding to earth with all labour and material requared complete the job in all respect upto the entire satisfaction of the Engineer-in Charge of the work. 4-way, TP & N (Horizontal)

upply and erection of PVC conduit pipe ISI marked (Medium) recessed in wall / ceiling etc. including cost of PVC bends, inspection box and all other material required to complete the job in all respect to the entire satisfaction of Engineer-in-Charge of work. (Make Diplast, Ravindra, AKG). 20 mm dia

Supply and erection of PVC conduit pipe ISI marked (Medium) recessed in wall / ceiling etc. including cost of PVC bends, inspection box and all other material required to complete the job in all respect to the entire satisfaction of Engineer-in-Charge of work. (Make Diplast, Ravindra, AKG etc.). 25 mm dia

Supply and rection of MS box made of 16G MS sheet recessed in wall, with arrangement of fixing brass screws, 2Nos. check nuts and one No. PVC bush of required size including all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-charge of work. 2 coats of primer

Supply and erection of socket size rotary step type electronic regulator for AC ceiling fan Anchor make Deluxe model No. 50440 ISA/SSK made PC561 operated on 120/280V AC. Supply complete including cutting of existing Bakelite sheet and making necessary connection etc. upto the entire satisfaction of the Engineer-in-charge of the work.

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary conneciton, complete in all respect. 20A switch (for AC)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary conneciton, complete in all respect. Blinking Plate

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary conneciton, complete in all respect. Fan regulator

Providing and fixing GI concealed sheet metal boxes with inner and outer faceplate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respect. 1&2 module (for telephone

Providing and fixing GI concealed sheet metal boxes with inner and outer faceplate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respect. 4 module (for AC)

Providing and fixing GI concealed sheet metal boxes with inner and outer faceplate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respect. 6 module (for electric supply to computer

Providing and fixing GI concealed sheet metal boxes with inner and outer faceplate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respect. 8M Plate

Supply and erection of PVC pipe ISI marked (Medium) recessed in wall / ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect upto the entire satisfaction of Engineer-in-charge of work. 32 MM pipe

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required.

Earthing with tinned copper earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) comlete as required.

xtra for charcoal or coke and salt for G.I. Plate or copper plate earth electrode.

supplying and laying of 6 SWG G.I.wire at 0.5 mts in below ground level as strip earth electrodes including thimble,soldering etc

earthing with GI earth pipe 4.5 mm long and 40 mm dia with messanary enclosure on the top as required

extra for using charaoal coke for pipe earth electrode as required

Pdg. and fixing 25 mm x 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode as required

Pdg. and fixing 25 mm x 5 mm G.I. Strip on surface or in recess for connections etc. as required with all labour and material.

Pdg. and fixing 25 mm x 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode as required

Supply and erection of 20 mm x 3 mm thick G.I. tape fixed with suitable G.I. stapples of same size

Supply and erection of under ground cable ,loose in existing pipe or trenches complete with necessary connections .(Make : polycab/Havells/Grandley etc.) 240 Sq. mm 3.5 Core Armoured Cable.

Supply and erection of under ground cable ,loose in existing pipe or trenches complete with necessary connections .(Make : polycab/Havells/Grandley etc.) 25 sq mm 3.5 core Al armoured cable

Supply and erection of under ground cable ,loose in existing pipe or trenches complete with necessary connections .(Make : polycab/Havells/Grandley etc.) 16 sq mm 4 core Al armoured cable

Supply and erection of under ground cable ,loose in existing pipe or trenches complete with necessary connections .(Make : polycab/Havells/Grandley etc.) 10 sq mm 4 core Al armoured cable

S/E of XLPE (E) 11 KV HT aluminum conductor armoured cable ISI mark laid in existing pipe /trenches/surface with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work. 50 sqmm 3 core XLPE Cable(Make : Polycab/Havells/KEI etc.)

S/E of mark double walled corrugated (DWC) HDPE pipe laid 1 Mtr. Below ground level including digging and refilling of earth including cost of suitable size socket / cuppler for HDPE pipe including cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer in charge of work. HDPE 65/50 mm outer dia / inner dia

S/E of mark double walled corrugated (DWC) HDPE pipe laid 1 Mtr. Below ground level including digging and refilling of earth including cost of suitable size socket / cuppler for HDPE pipe including cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer in charge of work. HDPE 90/75 mm outer dia / inner dia

S/E of mark double walled corrugated (DWC) HDPE pipe laid 1 Mtr. Below ground level including digging and refilling of earth including cost of suitable size socket / cuppler for HDPE pipe including cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer in charge of work. HDPE 145/122 mm outer dia / inner dia

Supply and laying of 1.1kV grade, 3Cx2.5 sq.mm Copper conductor PVC flexible cable as per IS 694 (to latest amendment) for street light uminaire.

Supply and installation of 3 Mtr Decorative pole (GAD Attached) of approved make with all components.

Supply, installation, testing and commissioning W4 40W LED WW" street light luminaire.

Supply & Erection of 20Mtr high mast shaft in Two sections suitable for wind speed as per IS 875, with raising lowering system comprising, head frame, luminaries carriage suitable to install luminaries in arrangement as per lighting design, double drum winch, SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box, lightening finial, foundation bolt. (Excluding foundation, Feeder pillar & Earthing).

Supply, installation, testing and commissioning 350W LED WH (MB)" flood light luminaire.

S/E of mark double walled corrugated (DWC) HDPE pipe 160/138mm laid 1 Mtr. Below ground level including digging and refilling of earth including cost of suitable size socket / cuppler for HDPE pipe including cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer in charge of work.

Supply and installation of standard High mast Feeder pillar STD 4. (Make : Tricolite , Adlec ,etc.)

Supply and installation of standard High mast Feeder pillar STD 7 with additional 1 no. of 6A SP MCB at outgoing (TYPE B). (Make : Tricolite , Adlec etc.)

Supply and installation of stand mounted, outdoor type, IP54, 3-Ph, 415V, 4 wired system, feeder pillar with LED phase indicating lamp, fabricated from 14 SWG CRCA sheet; complying to IS 8623 (to latest amendment) comprising of following components :(Make : Tricolite , Adlec etc.) Incomer: 32A TPN MCCB with single dial timer and 32A AC1 duty contactor. Outgoing: 12 nos. 6A SP MCB with neutral link.

Supply and installation of stand mounted, outdoor type, IP54, 3-Ph, 415V, 4 wired system, feeder pillar with LED phase indicating lamp, fabricated from 14 SWG CRCA sheet; complying to IS 8623 (to latest amendment) comprising of following components (MLDB):(Make : Tricolite , Adlec , etc.) Digital ammeter ,Voltmeter, ASS,VSS, with complete wiring Incomer: 125A TPN MCCB with single dial timer and 125A AC3 duty contactor. three phase and neutral 200A, AL bus bar Outgoing: 12 nos. 32A TP MCCB, 25KA with neutral link.

Supply and erection of suitable compression type brass cable glands for underground Cable. 3.5Cx240 sq.mm (1 no. DC Gland + 4 nos. Al Lugs)

Supply and erection of suitable compression type brass cable glands for underground Cable 3.5Cx25 sq.mm (1 no. DC Gland + 4 nos. Al Lugs)

Supply and erection of suitable compression type brass cable glands for underground Cable. 4Cx16 sq.mm (1 no. DC Gland + 4 nos. Al Lugs)

Supply and erection of suitable compression type brass cable glands for underground Cable. 4Cx10 sq.mm (4 nos. Al Lugs)

Supply, Installation, Testing & Commissioning of 115W LED flood light luminaire (RGB - AC 220V) of approved make.

Supply, Installation, Testing & Commissioning of 15W/M flexible LED strip 75W LED-RGB (RGB - DC 24V) of approved make.

Supply and installation of stand mounted, outdoor type, IP54, 3-Ph, 415V, 4 wired system, feeder pillar with LED phase indicating lamp, fabricated from 14 SWG CRCA sheet; complying to IS 8623 (to latest amendment) comprising of following components : Incomer: 32A TPN MCCB with single dial timer and 32A AC1 duty contactor. Outgoing: 12 nos. 6A DP MCB .(Make : Tricolite , Adlec etc.)

Supply & laying of following size Cables & PVC wire 4C x 2.5 sq.mm. XLPE insulated armoured Copper cable

Supply & Installation of following Junction Boxes: GI Junction Box-IP67, Size 150 x 150 x 100mm with suitable stud type terminal for terminating 4C x 2.5 sq.mm. armoured copper cable

Supply & Installation of following Junction Boxes: GI Junction Box for LED driver, IP-67, Size 200 x 200 x 100mm with suitable stud type terminal for terminating 4C x 2.5 sq.mm. armoured copper cable

Supply & termination of following sizes of cables: Polyamide cable Gland along with copper lugs suitable for termanating 4Cx 2.5 sq mm armoured copper cable

Supply & termination of following sizes of cables: Polyamide cable Gland along with Cu. lugs suitable for 2Cx 2.5 sq mm flexible copper cable

Supply & Installation of the following MISCELLANEOUS ITEMS: LED luminaire Driver type HLG-185H-24

Supply & Installation of the following MISCELLANEOUS ITEMS: Civil Foundation: Size 300x300x300 mm

Supply & Installation of the following MISCELLANEOUS ITEMS: "C" Type aluminium channel for fixing of LED strip

Supply & laying of following Conduit: 16mm dia. PVC flexible conduit for 2C x 2.5sq.mm. PVC flexible copper cable

Supply, Installation, Testing of following DMX CONTROL SYSTEM: DMX controller Input : 5-5.5V DC 0.6A, Output : DMX512 (x2),with in-built time clock, USB and Ethernet connectivity port for programming / control, Including 8 Scenes Push Button Panel and Power Supply.

Supply, Installation, Testing of following DMX CONTROL SYSTEM: DMX controller Input : 5-5.5V DC 0.6A, Output : DMX512 (x2),with in-built time clock, USB and Ethernet connectivity port for programming / control, Including 8 Scenes Push Button Panel and Power Supply DMX Cable.

Supply, Installation, Testing of following DMX CONTROL SYSTEM: Input: 5-5.5V DC 0.6A, Output: DMX512 9x2), with in-build time clock, USB and Ethernet connectivity port for programming / control, including 8 scenes push Botton Panel and Power Supply, DMX Splitter / Booster – XSP Series of approved make.

Supply, Installation, Testing of following DMX CONTROL SYSTEM: DMX controller Input : 5-5.5V DC 0.6A, Output : DMX512 (x2),with in-built time clock, USB and Ethernet connectivity port for programming / control, Including 8 Scenes Push Button Panel and Power Supply. Male Female sets.

Supply, Installation, Testing of following DMX CONTROL SYSTEM: DMX controller Input : 5-5.5V DC 0.6A, Output : DMX512 (x2),with in-built time clock, USB and Ethernet connectivity port for programming / control, Including 8 Scenes Push Button Panel and Power Supply. 20mm dia. PVC conduit for DMX cable

The 11kV UNIPACK Package Sub-Station shall be consisting of following: Make: ABB/Siemens/Schneider etc. HT SWITCHGEAR: 11kV 630Amps 20KA/3 sec. Non-Extensible Ring Main Unit having Two Numbers Manual operated Load Break Switch and One Number Fixed Manual Vacuum Circuit Breaker in SF6 insulated stainless steel enclosure with series trip, self powered microprocessor based numerical over current and earth fault relay protection.= 1No. Self Powered OC+EF protection relay with associated protection class CTs, suitable for Transformer rating. = 1No. Interconnection between HT Switchgear/Metering-Box and primary of transformer shall be done through 1C x 3 x 95 sq.mm Al. Unarmoured XLPE cable. = 1No. TRANSFORMER: 315KVA 11KV/433V DYn11 Oil filled hermatically sealed transformer with corrugated wall,without conservator type of design & Top Bushings for HT & LT with Off load tap switch of rating +5% to -5% @2.5%. Temp Rise and Losses as per IS1180 Energy Efficiency Level 02 (Star-1) (IS tol.) and Impedance as per IS1180 as per latest ISS specification. Oil Temperature Indicator with trip and alarm contact = 1No. Winding Temperature Indicator with trip and alarm contact = 1No. LVS PANEL - 500AMPS ALUMINUM BUSBAR INCOMER FROM TRANSFORMER: 500Amps 433V 50KA 4P Fixed MCCB with numerical overcurrent, short-circuit and earthfault protection = 1No. ON/OFF/TRIP LED Indications = 1Set. R-Y-B Phase indicating lamps = 1Set. Multifunction Meter for capturing various parameters such as kV, Amp, kVA, kW, pF, Hz etc. along with associated 500/5A, Metering CTs of Accuracy Class 1.0, 2.5VA = 1Set. OUTGOING MCCBs: 4 Pole, 200A , 35 kA =2Nos. 4 Pole, 160A , 35kA =2Nos., 4 Pole, 125A , 35kA =2Nos., 4 Pole, 250A , 35kA (Incommer for APFC) =1No., 4 Pole, 250A , 35kA (Incommer for APFC) =1No., APFC Panel with Relay for 120kVAR complete in all respect =1No. OUTDOOR ENCLOSURE: Outdoor type enclosure having construction of Galvanised Sheet Steel of thickness 1.5/2mm. The Enclosure shall have IP54 degree of protection for HT & LT switchgear compartment & IP23 degree of protection for Transformer compartment. The enclosure shall be Powder Coated. Each compartment will be provided with the door and pad locking arrangement. The Compartment illumination lamp with door operated switch shall be provided for each compartment. = 1Set. Interconnection & Earthing: Interconnection Between HT switchgear & Transformer using 1Cx3x95 Sq.mm XLPE Single core cable & Interconnection between Transformer & LT switchgear using AL. Busbars.Internal earthing connections by using 50 x 6mm GI strips. = 1Set. Outdoor Enclosure :- The enclosure shall be made of 2.0 mm thickness Galvanized Sheet Steel tropicalised to meet Indian weather conditions including all the partition sheets & doors.The base of the enclosure shall be of 4.0 mm thickness Hot Dip Galvanized Sheet Steel to ensure rigidity for easy transport & installation. The entire Package Substation shall be Factory Assemble & Factory Fitted. The enclouser shall have IP54 degree of protection for HT & LT switchgear compatment IP23 degree of protection for Transformer compartment. The temperature rise test on enclosure .The enclosure exterior shall be powder courted. Each compartment will be provided with door and pad locking arrangement. The compartment illumination lamp with door operated switch shall be provided for MV & LV comparatment.

Supply of 11KVPin Insulator Brown colour with 11KV Gi Pin with Disc fitting T&C type complete in all respect with erection of the same upto the entire satisfaction of the Engineer in Charge of work

Supply & Erection of Rubber mat of size 2mX1m & 12 mm thick suitable for 11 KV complete in all respect.

Supply & Erection MS bucket stand which including cost of 6 nos. buckets of 9 liter capacity with sand filling including cost of welding & painting of complete stand & buckets with one coat of red oxide and two coats of approved paint of red colour with all labour & petty material to complete the job in all respect upto the entire satisfaction of Engineer-in-charge of work.

Supply , Erection , testing & comissioning of 11 KV outdoor type HT Metering panel complete with CTs , PTs cubical and electronics Meter with accuracy class 0.5 as per requirement / approved by UHBVN. Panchkula Electrical Supply consisting of following : Cubical panel free standing floor mounting type made of sheet steel 14 G SWG CRCA sheet with channel iron base frame spray painted with strong synthetic grey channel paint as per size & design approved by UHBVN. PANCHKULA Electrical Supply.Out door Type with outer canopy. 3 nos. 11 KV CTs of rating as approved by UHBVN Panchkula. Chandigarh Electrical Supply for indoor installation of approved make of UHBVN Panchkula Electrical Supply. 1 no. 11 KV PTs 11000/110 volts 10 VA burden 0.5 accuracy oil filled suitable for indoor installation of approved make of UHBVN Panchkula Electrical Supply . Digital electronics meter 3 Phase 4 wire 11000 / 110 volts 10 VA burden 0.5 accuracy for recording reading of KWH of make and rating approved by UHBVN Panchkula Electrical Supply with push button display operating system for different kind of readings . Foundation of Suitable Size 300mm above ground level made of CC having suitable size to hold metering panel. Outer housing fab by 2mm thick CRCA sheet to cover the HT Metering Panel from rain water alongwith agnle iron frame. The cubical panel will be complete in all respect including interconnections , internal wiring with PVC copper cable its testing / approval of all items by UHBVN Panchkula Electrical Supply with a gurantee of one year from the date of commissioning including cost of all labour & material required to complete the job in all respect upto entire satisfaction of Engineer-in-charge of work..

Supply , Erection , testing & comissioning of 9 mtrs H-poleset with 9 pin GO Switch ,Pin Insulators,LA set, Iron C channel 75x6 mm 7 Nos, clamps, three earthing complete in all respect i/cost of Disc insulator etc. upto the entire satisfaction of Engineer -in Charge of work.

Supply , Erection , testing & comissioning of GI Fancing 7.5 Feet High From Finish Floor Level supported with GI Angle/ Channel complete in all repect upto the entire satisfaction of Engineer -in Charge of work.

Supplying,Testing , commissioning of 11KV HT End termination 3cx 50 sq mm (Make : Danson ,Birla 3M etc.) Indoor type

Supplying,Testing , commissioning of 11KV HT End termination 3cx 50 sq mm (Make : Danson ,Birla 3M etc.) Outdoor type

supply erection ,testing commissioning of exhaust fan 9inch with luvours

supply erection ,testing commissioning of 20w ,4 ft LED tube light

supply erection ,testing commissioning of ceiling fan 48 inch

Supply installation of 2 pair 0.5 sq mm telephone wire in existing pipe

Supply installation of 2 pair 0.5 sq mm cat 6 wire in existing pipe

Supply installation of Rj-11 in existing box

Supply installation of Rj-45 in existing box

Supply installation of 5 pin 6A socket with 3Mplate ,box

Supply installation of 5 pin 16A socket in existing plate

Supply and erection of hot water pipe medium class (B-class) G I as per 1239 with 25 mm thick insulation of 48 kg /cum density and k value +0.03 W/MKR value +1.67 sqmt C/W to withstand and temp of 250deg. erected in wall or surface incluidng all labour and material required to complete the job in all resepct 15 mm internal diameter of pipeline.

Supply and erection of hot water pipe medium class (B-class) G I as per 1239 with 25 mm thick insulation of 48 kg /cum density and k value +0.03 W/MKR value +1.67 sqmt C/W to withstand and temp of 250deg.erected in wall or surface incluidng all labour and material required to complete the job in all resepct 40 mm internal diameter of pipe line.

Supply and erection of polypropylene random (pp-r) hot water pipe as per IS_15801 with elbow ,tee, socket etc. recessed / on surface including all labour and material required to complete the job in all respect. 16 mm internal diameter.

Supply and erection of polypropylene random (pp-r) hot water pipe as per IS_15801 with elbow ,tee, socket etc. recessed / on surface including all labour and material required to complete the job in all respect. 20 mm internal diameter.

Supply and erection of polypropylene random (pp-r) hot water pipe as per IS_15801 with elbow ,tee, socket etc. recessed / on surface including all labour and material required to complete the job in all respect. 32 mm internal diameter.

Cutting holes up to 23 cm through stone masonry or brick work in cement wall for pipes and making good including repainting, re-plastering and finishing according to existing finish where required white washing where required. 22.86 cm thickness of wall

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge). INDIAN TYPE ORISSA OR ORYA WATER CLOSET SUITE for sinking into floor, with raised foot treads COMPLETE WITH 100 MM G.C.I.’P’ TRAP with or without vent as required and all OTHER NECESSARY FITTINGS as fully described in item no.30.1 above. Mixed Colour.

EXTRA OVER item nos. 30.1 TO 30.4 AND 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY VITREOUS CHINA HIGH LEVEL CISTERN COMPLETE with internal brass fittings instead of 12.5 litres capacity high level C.I. eistern complete (as approved by the Engineer-in-charge Mixed colour

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (as approved by the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT, SYPHONIC TYPE, consisting of-VITREOUS CHINA WARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in charge). mixed Colour

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE FLEXIBLE TUBE 15mm x 450mm

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE A RANGE OF four URINALS LARGE FLAT BACK OR ANGULAR LIPPED FRONT 610MM HIGH IN VITREOUS CHINAWARE WITH ONE NO. 10 LITRES CAPACITY BEST INDIAN MAKE C.I. AUTOMATIC FLUSHING CISTERN WITH FITTINGS AND FLUSH PIPE ETC.COMPLETE as fully described. Mixed colour

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (ORDINARY) LAVATORY SUITES consisting of Lavatory in VITREOUS CHINAWARE size as give below ( to the approval of the Engineerin- charge) including china plug for tap hole where necessary ; R.S. or C.I.BRACKETS for building into wall including painting; 32mm C.P.BRASS WASTE WITH C.P. brass chain and rubber plug; 15mm C.P.BRASS SCREW DOWN PILLAR TAP WITH jam nuts or couplings best design (as approved by the Engineer-in-charge) ALL FITTINGS BEST INDIAN MAKE and; to the approval of the Engineer-in-charge. ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and MAKING GOOD THE WALLS, FLOORS AND PAINTING OF FITTINGS ETC. Mixed colour size 690MM X 550MM X WITH ONE NO. TAP Mixed colour

Providing and fixing in position best Indian make Pedestal fittings of vitreous chinaware complete (as required by the Engineer-in-charge) Mixed colour

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making good the wells etc.) Mixed colour

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with raw slugs embedded in walls with C.P. brass screws. Complete in all respect INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. 25 mm dia C.P. Brass adjustable 750 mm long.

Providing and fixing in position best indian make beveled edge 5.5 MM TH. mirror mounted on ASBESTOS sheet Ground fixed in in position by means of 4 no. Chromium plated brass screw and washers over rubber washers and rawl plug embedded in the wall of chromium plated brass clamps with C.P. brass screws (as required by the Engineer-in-charge) single colour

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge). Bib cock long body.

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineerin- charge) Stop cock male & Female.

PROVIDING AND FIXING IN POSITION H.C.I.SPECIALS FOR SOIL, WASTE, VENTOR ANTI-SYPHONAGE PIPES TO I.S.I MARKED INCLUDING cutting and wastage etc., CUTTING HOLES IN WALLS ROOFS OR FLOORS ETC, AND MAKING GOOD to its original condition BUT EXCLUDING COST OF LEAD JOINTING. For 110 mm pipes. PVC cowls

PROVIDING AND FIXING IN POSITION H.C.I.SPECIALS FOR SOIL, WASTE, VENTOR ANTI-SYPHONAGE PIPES TO I.S.I MARKED INCLUDING cutting and wastage etc., CUTTING HOLES IN WALLS ROOFS OR FLOORS ETC, AND MAKING GOOD to its original condition BUT EXCLUDING COST OF LEAD JOINTING. For 110 mm pipes.Bend with door heavy.

PROVIDING AND FIXING IN POSITION H.C.I.SPECIALS FOR SOIL, WASTE, VENTOR ANTI-SYPHONAGE PIPES TO I.S.I MARKED INCLUDING cutting and wastage etc., CUTTING HOLES IN WALLS ROOFS OR FLOORS ETC, AND MAKING GOOD to its original condition BUT EXCLUDING COST OF LEAD JOINTING for 75 mm pipe PVC Bend.

PROVIDING AND FIXING IN POSITION H.C.I.SPECIALS FOR SOIL, WASTE, VENTOR ANTI-SYPHONAGE PIPES TO I.S.I MARKED INCLUDING cutting and wastage etc., CUTTING HOLES IN WALLS ROOFS OR FLOORS ETC, AND MAKING GOOD to its original condition BUT EXCLUDING COST OF LEAD JOINTING. for 75 mm pipe PVC P-trap.

Providing and fixing in position M.S.or heavy flat iron clamp made out of M.S. flat not less than 5 mm of the approved design for fixing C.I. SOIL WASTE vent or anti pipes to walls Complete in all respect including cutting and making good the wall and floor etc. and painting.For 100 mm internal diameter pipes.

Providing and fixing in position M.S.or heavy flat iron clamp made out of M.S. flat not less than 5 mm of the approved design for fixing C.I. SOIL WASTE vent or anti pipes to walls Complete in all respect including cutting and making good the wall and floor etc. and painting. For 75 mm internal diameter pipes.

Cutting chase in brick wall in cement or in floor & embeddeing G.I.OR H.C.I.Pipe lines and making good the same to its original condition Size 75 mm X 75 mm.

Providing and fixing HDEP Water storage tank of Sintex, OK Supreme make with cover/lids marked with IS:12701 on roof top buildings including cost of hosting and placing in position, making connections with inlet outlet pipes, providing overflow & scour provision with suitable plug on score pipe including cost of nipple, washer flanges for connection in tanks complete in all respect to the satisfaction of Engineer-in-charge ( Except civil work ) 2000ltr capacity

Supply and erection of Taps of made of Gun metal ISI marked including all labour and material required to complete the job in all respect. 15 mm diameter.

Construction of brick masonry inspection chamber size as given below up to to 0.60 meter average depth in cement mortar 1:5 lime concrete with 40 percent lime mortar 2:3 in foundation cement concrete 1:2:4 benching 12mm thick cement plaster 1:2 with a floating coat of 1mm thick of 455 mm x 455mm /455mmx610mm inside light duty LIGHT DUTY C.I.INSPECTION CHAMBER COVER AND FRAME weight as per I.S.I. specification painted WITH 3 COATS OF black bitumenstic superior paint complete as per standard design. Size 600 mm X900 mm inside (with 455 mm x 455 mm cover and frame light duty single seal weighing 20 kg with R.C.C. slab).

providing and fixing PVC rain water pipe 6kg pressure of ISI mark in cement mortar during masonry work.150 mm dia PVC pipe 6 kg pressure.

Providing and fixing PVC bend ISI mark 150 mm dia PVC bend

Boring/ drilling bore well of required dia for casing/strainer pipe, by suitable method prescribed in IS:2800( part I), Including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants and machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.(All types of soil.) up to 90 metre-150 mm dia

Providing & Lowering 150 mm outher dia pvc pipe filter with jali & plian (10kg /mtr). Completes in all respect (ISI) beyond 90 metre 150 DAI

Providing & fixing MS Clamp for suitable pipen with nut & bolt .Completes in all respect (ISI)

Providing & fixing PVC cap for 150 mm outer dia pvc pipe .Completes in all respect (ISI)

Development of T/W with Air/Compressor OR Satisfaction withEngineer-in-charge .

Providing & Lowering delivery pipe 30 mm outer dia pvc pipe

Providing & fixing a Submersible Water Pump with all fittings of approved make.

ravi singla engineers and contractors

M / S DAYANAND CONTRACTOR