PROVN OF STAINLESS STEEL RAILING AROUND VICTORY GARDEN AT BINNAGURI AND SPECIAL REPAIR TO BLDG NO P-9 (QM STORE) OF

Amount

Demolition of cement concrete (un reinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided complete all as specified.

Demolition of brickwork or stone/boulder masonry, built in cement mortar complete all as specified.

Dismantling wrought iron or mild steel work of any description as in door, gates , truss etc and similar works complete all as specified.

Surface excavation n exc 30cm deep and average 15cm deep and getting out in soft/ loose soil complete all as specified.

Taking down of cement plaster on brick (or) concrete wall including racking out joints hakins for key sinebling down with water etc complete all as specified.

Taking down chowkat or frame with door shutter (without taking off shutter from the frame) exc. 1.5 SQM and n.exc 4 SQM each, making good disturbed surfaces and removing materials from site of work complete all as specified.

Excavation in trenches soft /loose soil not exc 1.5 wide and not exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, mainholes , pier holes etc not exc 10 SQM on plan and not 1,5 m in depth and getting out complete all as specified.

Returning, filing in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in any type of soil etc complete all as specified.

Removing surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified.

Removal of excavated materials exceeding 250 m but not exceeding 500 mand depositing where directed etc complete all as specified

Supply and lay dry river sand filling for under ground cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified.

M&L for providing cement concrete type B-0 (1:2:4)(using 12.5 mm size graded aggregate) as in coping set incl weathering, slightly rounded or chamfered angles & thickness complete all as specified.

Material and labour for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surfaces of concrete all as directed.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping).

Removal surplus soil / debries outside the defence land distance exc 250m and upto total distance 500m complete all as specified.

Material and labour rendering 15mm thick cement plaster in CM 1:4 on fair faces of brick/concrete work surfaces in two layer top 5mm layer mixed with integral water proofing compound all as per manufacturer's instruction and as specified. Make: 'Plastocrete Plus' of Sika/ 'Pidiproof LW' of Pidilite for water proofing compound. Note: (i) WPC shall be measured and paid for separately as 'Supply only'. (ii) WPC to be mixed @200ml per 50 Kg bag of cement all as manufacturers instruction.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement morter 1:6 finished even and smooth without using extra cement complete all as specified.

M&L rendering 5mm thick in CM (1:3) on fair faces of concrete surfaces as in celling finished fair and even without using extra cement complete all as specified.

M&L of two coat of synthetic enamel paint over one coat of red oxide on new steel surfaces of any description over 10cm in width or girth incl preparation of surfaces complete all as specified.

M&L preparing old painted steel surface of any description not otherwise described for over 10 cm width or girth and applying one coat of synthetic ennamel paint complete all as specified.

M & L preparation of new surface & applying two coats of synthetic enamel paint over a coat of pink primer to wooden surfaces exc 10 cm girth complete all as per manufacturer's specification and as specified.

M&L preparing old painted wooden surface of any description not otherwise described for over 10 cm width or girth and applying one coat of synthetic ennamel paint complete all as per manufacturer's specification and as specified.

M&L brickwork with sub class B bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:4 by using old size bricks complete all as specified.

M&L brickwork with sub class B bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks complete all as specified.

S&F Framed work such as grills,gratings, etc with ends of bars shouldered and/or riveted,or forged into spikes; framedguard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified.

S&F Framed work as in stainless steel (SS-304 grade) work with ornamental design and similar work of various sections including welding complete all as specified.

M&L applying two coats of weather proof exterior emulsion paint of standard quality and make ,over a coat of primer including preparation of new wall surfaces complete all as per manufacturer's specification and as specified.

M & L for preparing new Plastered surfaces of walls and finishing the walls with Acrylic smooth exterior emulsion paint of required shade for New work over and including priming coat of exterior primer applied complete all as per manufacturer's specification and as specified.

.M & L for complete removal of existing treatment and finishing the walls with Acrylic smooth exterior emulsion paint of required shade for Old work over and including priming coat of exterior primer applied complete all as per manufacturer's specification and as specified.

S&F Granite (of any type and colour) work, thickness of granite 16-18 mm (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cemnt (1:2) using marble dust with admixture of pigment to matchwith shade of granite complete all as specified.

M&L for Endura tiles of size 300x300x10 mm set, jointed and pointed in neat cement slurry over in pavement/footpath/floors over incl 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified.

Removing existing water proofing treatment to complete any descrption/any thickness and in any position including removal of rubbish of the premises etc complete all as specified.

M&L for cement concrete type Bo 1:2:4 (using 12.5mm graded stone aggregate) 25mm thick as in roof to achieve slope on existing roof surface complete all as specified.

M & L for water proofing treatment to RCC roof slab complete all as specified and as follows:- (a) 10 mm th cement plaster in CM 1:4 with integral WPC to be laid over the RCC roof slab when the concrete is green. (b) Supply and laying 3mm thick five layered polymeric APP membrane (weight not less than 3 Kg per Sqm) reinforced with non-woven polyester matt of central core 90 micron thick (weight not less than 150gms/sqm) high density polythene film, protected on both sides with high quality polymeric asphaltic mix protected on both sides with thermo-fusible HM HDPE film laid on primed surface by torch application over compatible primer at 0.4 Ltr / SQM of density at 25 degree centigrade 0.87 - 0.89 kg/ltr and viscosity 70-160 cps or cold sticker and torch application of membrane with overlap while torching shall be 150 mm on length side and 100 mm on width side after necessary preparation of surface complete as per manufacturers instructions. Make: “Torchshield P2160” of Pidilite/ “Super thermolay: of STP or equivalent. Note: (i) Membrane shall be laid using butane torch and sealing all joints etc all as per Para 11.44.5 of SSR Part-I.

M&L for 25 mm thick cement concrete type B1, 1:2:4 (20 mm graded aggregate) as in floor etc and finishing cement concrete complete all as specified.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with M & L for screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified.

M & L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with ditto as per item 6 above complete all as specified.

M & L for hard core of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified.

M&L for cement concrete type C-2, 1:3:6 (40mm graded aggregate) 75mm thick as in plinth protection, footpath , under paver block etc and finished the surface even and smooth complete all as specified.

M & L 80 mm thick M-30 grade factory made vibratory compacted cement concrete rubber moulded, interlocking paver block any shape and size confiroming to IS 15658-2006 with grey cement and pigment as approved laid over and incl 50 mm thick consolidated sand cushion and joints filled with sand complete all as specified.

M&L for preparing new plastered surfaces of wall and applying three coat of white wash complete all as specified.

M&L for preparing old plastered surfaces of wall and applying two coat of white wash complete all as specified.

M&L preparation of new plaster surface and applying three coats of white wash on ceiling complete all as specified.

M&L preparation and complete removal of existing treatment of old plaster surface and applying three coats of white wash on ceiling complete all as specified.

Supply only liquid water proofing compound (WPC) of best quality complete all as specified.

M & L pressed steel door frame of size 105mm x 60mm with one or more rebates including necessary fixing lugs , hinges, lock strike plate etc complete as specified.

S&F 30mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified.

S&F Aluminium anodized barrel tower bolts, extruded section 200mm long complete all as specified.

S&F Aluminium anodized handles, D type, 150mm long complete all as specified.

S&F aluminium sliding door bolt 300 mm long, plate type, stove enamelled black, with bright bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified.

Supply & fixing in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless and as required framing including taking old one steel staples complete all as specified.

S&F in repairs factory made Z section steel window with side hung shutter frame including projecting/ box type hinge with steel handle and steel peg stay, ms tower bolt etc. complete with glazing bars , dovetailed or welded including a shop coat Red Oxide priming complete including taking out old one all as specified.

S&F in repairs factory made Z section steel ventilator with top hung shutter incl hinges, steel peg stay, with glazing bars including a shop coat Red Oxide priming including taking out old one , complete all as specified.

M&L for plain cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate ) as in surface channels and drains etc complete all as specified.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified.

M&L for point wiring complete with 1.5 SQMm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 SQMm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sundn terminal box made out of GI sheet steel not less than 1.22 mm thick for boxes upto a size of 200 x 300mm and above this size not less than 1.63 mm thick duly painted with aluminum inside and anticorrosive paint outside, concealed in walls, with 3mm thick bakelite/plastic laminated sheet top cover fixed with cadmium plated iron screws for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCBs or bus bar shall be sone through proper size copper/brass thimbles. Where concealing of conduit is not feasible ie on surface of roof etc, conduit shall be fixed on surface with necessary saddles at no extra cost, One light point controlled by one way switch 5/6 amps all as specified.

ALL as per item No 68.00 but One ceiling fan/Exhaut fan point controlled by one way switch 5/6 amps complete all as specified.

ALL as per item No 68.00 but One socket out let 5/6 amps point on the same board complete all as specified.

ALL as per item no. 68.00 but One socket out let 5/6 amps point on the independent board complete all as specified.

All as per item No 68.00 above but multi stranded coppper conductor of size 2.5 SQMm for 15/16 Amp point on independent board complete all as specified.

S&F switch piano flush type 5/6 amps single pole one way complete all as specified.

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified.

S&F of socket outlet 2 in 1, 5 Pin, 5/15 amp, multipurpose 230 volt flash type complete all as specified.

S&F switch piano flush type 15/16 amps single pole one way complete all as specified.

S&F Ceiling rose, surface type with back plate, three terminal /PVC/ polycarbonate, isolated body complete all as specified.

S & F deluxe fan electronic regulator 230 volts AC 50 Hzs rotary step white/ivory finish complete all as specified.

S&F, IP 20, class I, LED tube light fittings 20W (or nearest next higher wattage) (4feet), wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting complete all as specified.

S & F LED street light fittings 35 Watt ,230 VAC outdoor type with high pressure die cast aluminium housing, heat resistant, toughned glass cover with IP66 protection complete all as spedified.

S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole & neutral with din rail, IP-20 protection suitable for fixing MCB"S/lsolators complete including provision of blanking plates as required and taking down the old one complete all as specified.

S&F MCB, Single pole & neutral 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified.

S&F MCB, Single pole, 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified.

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete including taking out the old one complete all as specified.

M & L Sub main wiring concealed type with two run single core cable PVC insulated cable with 4.0 SQMm (Nominal area) multi stranded copper conductor FRLS cable 1100 volts gde incl earth continuity conductor using PVC insulated cable of stranded copper conductor of size 4.0 SQMm connected to common earth dolly and drawing into rigid PVC conduits of 25 mm dia medium grade size, making good the disturbed surfaces complete including necessary taking down.(NOTE : Two run of submain wiring cable alongwith one run of earth wire shall be measured as one length. .

M&L for street light bracket made out of GI pipe light grade 32 MM dia 1.2 mtr length bent to shape and reduced to required size at top upto 1.2 mtr length by cutting, welding and well finishing including MS clamp of flat iron of size 25 x 5 mm suitable length 2 Nos complete with drilling hole, fixing with runts bolts and washers including painted with two coats aluminium paint over a coat of red oxide primer complete all as specified.

Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulated PVC bedded, galvanized steel strip or wire armoured LT electric power UG cables, heavy duty with stranded aluminium conductor of cross sectional area 16 SQMm 2 core with and including all fixing & connecting accessories such as Aluminium cable lugs, cable gland, nut, bolts, washer etc including taking out old cable complete as specified.

M&L for 40 mm bore steel tubing light grade ISI marked for protection of cable including necessary joints complete all as specified. Make: Tata/Jindal/Bansal

Supply and fix 4mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in eash pane complete all as directed.

M & L for horizontal boring across the existing road without disturbing the road surface for inserting GI pipe complete all as specified. Note :- (i) Removal of surplus soil shall be deemed to be include in the unit Rate. (ii) GI pipe will be measured and paid separately under relevant item of Sch 'A'.

Supply and laying sub class B bricks of size 25cmx12.5cmx7.5cm (+/-10% tolerance) for protection of UG cable with width equal to length of bricks as mechanical protection laid dry and flat complete all as specified.

M/S RATNESH KUMAR SINGH (BID ID -3200357)

ANUP ENGINEERING WORKS (BID ID -3201160)

M/S RELIABLE CONSTRUCTION CO. (BID ID -3200237)

M/S SINHA ENTERPRISE (BID ID -3201663)

M/s Sohini Construction (BID ID -3201139)

M/S SHIVNATH SINGH (BID ID -3201244)

Shri Amarnath Sah (BID ID -3202139)