PROVN OF SWT IN TECH AREA, PROVN OF CERTAIN WORKS SERVICES IN TECH AREA AND CONSTRUCTION OF TOILETS FOR CHILDREN WITH SPECIAL NEEDS AT AF STN BAREILLY UNDER GE (AF) BAREILLY

Amount

B/R PORTION Surface excavation not exc 30cm deep and averaging 15 cm deep and getting out in any type of soil.

Excavation over areas not exc 1.5 mtr in depth and getting out in soft / loose soil all as specified.

Excavation over areas exc 1.5 mtr in depth but not exc 3.0 mtr deep and getting out in soft / loose soil all as specified.

M&L for cement concrete type B-2, mix 1:2:4 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer in soil all as specified.

Removing surplus excavated material (soil) to a distance exc. 50 mtr and not exc 100 mtr and deposited where directed at level not exc. 1.50 mtr above the starting point all as specified.

M&L for reinforced cement concrete M-30 (Design mix) as in foundation including rafts, footings, foundation beams,plinth beams, bases for columns etc, basement slabs, under reamed piles and mass concrete as in SWT complete all as specified.

M&L for reinforced cement concrete M-30 (Design mix) using 20 mm graded stone aggregate for walls, retaining walls of any thickness etc as in SWT etc all as specified.

M&L for from work to side of curved concrete foundations, footings, bases of columns, raft and raft beams, sides and soffit of plinth beams and similar work, vertical or to better fair finished as in SWT all as specified.

M&L for from work to curved faces of walls, retaining walls etc fair finished surfaces as in SWT all as specified.

M&L for mild steel TMT bar 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips.

M&L for brick work with sub-class `B' bricks, straight or curved on plan exc 6.0 mtr mean radius and built in cement mortar 1:6 all as specified.

M&L for 15 mm thick rendering in cement mortar (1:4) on brick or concrete surfaces including finishing surface fair and even without using extra cement including mixed with liquid WPC as per manufacturer's instruction complete all as specified. (Note :- WPC will be measured and paid separately).

Supply only liquid water proofing compound.

M&L for hard core of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified.

M&L for cement concrete type D-2, mix 1:4:8 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete sub base of floor etc complete all as specified and directed.

M&L for 100 mm thick cement concrete in 1:2:4 mix, type B-1 (using 20 mm grade stone aggregate) as in floor finishing top surface including finishing surface even and smooth without using extra cement.

M&L for forming contraction (Dummy) joints 65 mm deep x 10mm wide filled with sealing compound grade 'A' complete all as specified.

M&L for prepration of newly plastered surface of wall and applying two coats of cement base paint all as specified.

M&L for preparation of newly steel surfaces of any description not exc 10 cm width or girth and applying two coats of synthetic enamel paint (1st quality) over one coat of red oxide zinc chromate primer complete all as specified.

Excavation in trenches not exc 1.50 mtr wide and 1.50 mtr in depth for foundation etc or for shafts, wells, cespits, manholes, pierholes etc not exc 10 Sqm on plan and getting out in soft / loose soil all as specified.

M&L for spreading and leveling in layers not exc. 25cm thick, well ramming including watering as required.

M&L for form work to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beam and similar works in rough finished flat surface of concrete complete all as specified.

M&L for form work to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished surface of concrete complete all as specified.

M&L for formwork to sides soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surface of concrete all as specified.

M&L for reinforced cement concrete M-25 (Design Mix) using 20 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, base of columns and the like complete all as specified.

M&L for reinforced cement concrete M-25 (Design Mix) using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.50 m span and the like complete all as specified.

M&L for reinforced cement concrete M-25 (Design Mix) using 20 mm graded stone aggregate as in columns, pillars, piers, posts, struts and the like complete all as specified.

M&L for reinforced cement concrete (Design mix) M-25 grade using 20mm graded aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like concrete all as specified.

All as per item No. 11 above but for 8mm dia and over up to and including 10mm dia in stirrups, spaces and binder etc complete all as specified.

M&L for 15 mm thick rendering in cement mortar 1:6 on fair face of brick work or concrete surfaces including finishing surface even and smooth without using extra cement all as specified.

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces including finishing surface even and smooth without using extra cement in ceiling complete all as specified.

M&L for three coats of white wash on ceiling including preparation of newly plastered surfaces all as specified.

M&L for prepration of newly plastered surface of walls and applying two coats of white wash on wall surfaces complete all as specified.

M&L for treating the back fill in contact with foundation at the rate of 7.5 litre of emulsion per sqm of vertical surface (area of the sub structure in contact with back fill to be measured) complete all as specified and directed.

M&L for treating the top surface of filed earth at the rate of 5 litre of emulsion per Sqm of surface complete all as specified and directed.

M&L for treating the soil under plinth protection at the rate of 5 litre of emulsion per Sqm of surface area complete all as specified and directed.

M&L for treating the soil alongwith external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter of wall complete all as specified.

M&L for cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete, sub base for flooring etc. all as specified and as directed.

M&L 75 mm thick cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate) as in plinth protection, laid in bay not exc 3.00 sqm each including finished even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints through out the thickness of plinth protection duly filled with bitumen mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed.

S&F for non skid coloured ceramic tiles 400 mm x400 mmx 7 to 8 mm thick as in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile laid over 15 mm thick screed bed in cement mortar 1:6 all as specified.

M&L for glazed ceramic coloured/printed tiles 350 mm x 250 mm x 7 mm/ 450X 350X 7mm thick as on vertical surface such as skirting, dado, wall etc, set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tile over 10 mm thick rendering in cement mortar 1:4 all as specified.

S&F in repair vitreous china wash basin, Oval type, snow white, flat back of size 560mm x 400mm over and including 18 to 20 mm thick 'Z' black granite stone slab (table rubbed and polished) including bull nosed as on shelves for cooking plateform/ WHB /pillars etc over and including 20 mm thick screed bed in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white /coloured cement to match the shade complete all as specified.

S&F in repair Vitreous china wash down water closet pan semi-pedestal pattern (Anglo-Indian type) white excluding flushing cistern but including PVC flush pipe & PVC sheet cover closed pattern complete all as specified.

S&F in repair chromium plated Jet with flexible cord suitable for EWC including fixing to steel pipe or union all as specified.

S&F in repair PVC low level flushing cistern white 10 Litres capacity, valve less, with inlet, ball valve, float and handle including brackets, PVC flush bend pipe, complete all as specified.

S&F in repair chromium plated health faucet with hand shower & flexible cord suitable for EWC including fixing to steel pipe or union of 15 mm bore dia, (Health Faucet) with 8 mm dia 1.2 Mtr long flexible tube & wall hook) complete all as specified.

S&F in repair 15mm dia stop valves/ angle cock, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed but fancy type chromium plated with long shank and cup all as specified.

S&F in repair vitreous china urinal, full stall type, white including flushing cistern, flush pipe and waste pipe complete all as specified.

S&F in repairs PVC connection 45 cm long with two nuts and washers complete all as specified.

S&F in repair 15 mm dia two way bib taps, chromium plated with fancy type, long body with screwed down, screwed for iron pipe all as specified.

S&F in repair 15 mm bore chromium plated pillar taps, cast copper alloy, with captan head screwed down high pressure with or with out lettred Hot or Cold with long screwed shanks swan neck and fly nut screwed for iron pipe or for brass ferrule.

S&F for CP greating125 mm dia with or with out hole to match the colour of floor tile all as specified and directed (Min Wt 40 gms).

S&F for sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as specified

S&F for tubular towel rail 20mm dia D type 60cm long between flanges brass chromium plated complete fixed to walls.

S&F for rotational moulded polyethylene water storage tanks three layers (Cylindrical vertical with closed top) of 1000 ltrs capacity hoisted and fixed in position all as specified and directed.

S&F for PVC ball cock, 20 mm bore high pressure of PTMT eppoxy coating aluminium rod with polythene float and flynut complete, screwed for iron pipe all as specified. (Min wt 210gm )

S&F for 20mm dia Gun-metal, glove or gate valves, with iron wheel head, screwd both end sor iron pipe and fixed

S&F for cast iron floor trap long neck type 75 mm bore without greating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified.

S&F for 75 mm bore cast iron (sand cast) soil, waste and vent pipe in any length with or without ears with lead joint laid in tranches or fixed to wall all as specified.

S&F for 100 mm bore cast iron (sand cast) soil, waste and vent pipe in any length with or without ears with lead joint laid in tranches or fixed to wall all as specified.

S&F for 100 mm bore cast iron bend (any radius), diminishing piece or taper (larger bore measured) all as specified.

S&F for 75 mm bore cast iron bend (any radius), diminishing piece or taper (larger bore measured) all as specified.

S&F cast iron cowl for 100 mm bore pipe.

S&F for stack clamps for 100 mm bore pipe out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified.

S&F for 20 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified.

S&F for 25 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified.

S&F for brass elbow (3/4 inch X ½ inch)

S&F for brass tee

S&F for male brass threaded Adaptor (MTA/ MBTA) )

S&F for female brass threaded adaptor (FTA/ FBTA

M&L for factory made singal extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkat of size 50 x 100mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm², modules of elasticity 900 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

M&L for factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm², modulus of elasticity 850 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: Butt hinges and necessary screws shall be paid separately)

S&F for 300 mm long aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F for 100mm long stainless steel butt hinges complete all as specified.

S&F for 600 mm extruded aluminium alloy handles, fabricated type, anodised complete all as specified.

S&F for 300mm mild steel ordinary rat tail rod patttern springs includding roller and roller plate complete

S&F for 150 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed.

M&L for water proofing treatment on approachable roof comprising the following specifications : (a) 10mm thick screed bed in cement mortar 1:3 mixed with polymer based water proofing compound when levelling coarse is still green. (b) After the surface is fully dried, applying a coat of bituminous primer @ 0.30 liters/Sqm. (c) After primer, the entire roof surface shall be painted with hot, blown bitumen grade 85/25 confirming to IS-702 @ 1.2 Kg/Sqm. (d) Over hot bitumen, polymeric water proofing membrane consisting of 90 to 100 micron thick central core of HMHDPE film and weight not less than 3 Kg/ Sqm shall be laid with 100 mm side lap/ end lap on prepared surfaces as per manufacturer’s instruction complete all as specified.

M&L for applying a coat of aluminium paint @ 0.20 Ltr /Sqm complete all as specified.

S&F for anodised aluminium powder coating (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified all as specified.

S&F for anodised aluminium powder coating (minimum thickness of powder coating 50 micron) window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 No.) suitable handle (1 No.) complete all as specified

S&F for anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge.

S&F for 5.50 mm thick sheet glass(tinted/reflective type) in square each pane complete

S&F for stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

M&L for 150 mm bore reinforced concrete pipes, class NP-3, laid and jointed with collars in trenches and jointed in cement mortar 1:1 with spun yarn complete all as specified.

M&L for cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in bed to drain pipes of 150 mm bore including packing under and haunching against the sides of pipe after they are laid and tested all as specified.

M&L for cement concrete type B-1 mix 1:2:4 using 20 mm graded stone aggregate as in coping, beds block for embedding hold fast, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work all as specified.

M&L for cutting into existing manhole for connecting new drain, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150 mm dia pipe complete all as specified.

S&F for stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc, including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified.

M&L for fly ash brick works, straight or curved on plan exc 6.0 mtr mean radius built in cement mortar 1:6 complete all as specified.

M&L for 100mm thick cement concrete type D-2, 1:4:8 mix (using 40mm graded stone aggregate) as in sub base complete all as specified.

Excavating in post holes (or similar holes) each not exc 0.5 Cum and getting out in in soft/loose soil, returning, filling in and raming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance not exc 50 mtr and making good surface all as specified.

M&L for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St.-240 all as specified. (Note :- All structural member including tubular truss should be mechanically curved all as directed by Engineer-in charge and the quoted rate deemed to be included in the item)

M&L for plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases. splices, angle brackets, cleats and other connections conforming to Fe 410W (Gde E-250) quality A complete all as specified.

S&F for pre-painted galvalume aluminum zink coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self coaching screw as specified. (Note:- Colour and design as approved by Engineer-in-charge)

M&L for preparation of newly steel surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint (1st quality) over one coat of red oxide zinc chromate primer complete all as specified.

E/M PORTION S&F for point wiring with 1.5 Sqmm FR-LSH PVC insulated unsheathed copper conductor single core multi stranded cable 650/1100 volts grade drawn in and including concealed non-metallic rigid PVC conduit medium grade with all fittings (ISI marked) not less than 20 mm external dia fixed concealed / recessed on wall / ceiling etc including 1.5 Sqmm FR-LSH PVC insulated unsheathed copper conductor single core multi stranded cable 650/1100 volts gradeas earth continuity wire including MS sunken pressed steel terminal boxes of suitable size, made of sheet 1.6mm thick with 3.0 mm thick bakelite sheet top cover for one light point / Fan point controlled by one way switch complete all as specified.

All as per item No. 100.00 above but with 2.5 sqmm single core 1100V grade FRLSH PVC insulated unsheathed multistranded copper conductor and 2.5 sqmm single core 1100 volt grade FRLSH PVC insulated unsheathed multistranded copper conductor as earth continuity conductor connected to comman earth dolly complete all as specified.

S&F for wall / surface mounted type LED light fitting batten type with LED 1x 20 Watt (4 feet long), extruded aluminium body with heat sink provided for efficient heat dissipation and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with 3 core twisted flexible copper conductor cable complete all as specified.

S&F for switch piano flush type one way 5 Amp, 240 volts all as specified.

S&F for switch piano flush type one way 16 Amp, SP 240 volts all as specified.

S&F for socket outlet 2 in 1, 3 pin, 5/6 & 15/16 Amp flush type all as specified.

S&F for ceiling rose 65 x 50mm three terminals all as specified.

S&F for flush mounting factory made TPN DB's Double door, IP-43 Protection, IK-09 with metal door, with neutral bus bar, Earth bar and cables ties for cable management fully insulated bus bar 4 way etc complete all as specified.

S&F for MCCB 100 Amp, 415 volts, 4 pole, thermal magnetic release for line protection etc all as specified and directed (Incoming for LT Panel).

S&F for MCCB 63 Amp, 415 volts, 4 pole, thermal magnetic release for line protection etc all as specified.

S&F for MCB, 6 - 32 Amp, SP (single pole), 240 volts, 50HZ, 10 KA, ‘C’ series all as specified.

S&F for sub main wiring of 1100 volts grade heavy duty two single core 2.5 Sqmm size (nominal area) PVC insulated (FRLS) copper multi-stranded conductor cable drawn into & including PVC conduit medium grade not less than 25 mm dia including its all accessories & fittings, fixed concealed with and including chase cutting and making good the existing surface along with a continuous run of 2.5 Sqmm size (nominal size) stranded copper conductor PVC insulated (FRLS) (green colour) cable as earth wire complete all as specified and directed. (NOTE: - TWO SINGLE CORE CABLES ALONG WITH EARTH WIRE AND PVC CONDUIT SHALL BE MEASURED AS ONE UNIT LENGTH).

M&L for making horizontal hole by mechanical boring under hard standing, pavements or roads for insertion of GI pipes 40 to 80 mm bore and making good the disturbed surface complete all as specified.

S&F for 40 mm bore galvanished iron tubing, light grade, ISI marked laid in trenches or inserting in horizontal boring for cable protection including fixing with MS Clamp and nut bolts complete all as specified.

S&F for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to earth lead wire of GI wire 4mm dia by means of nuts/bolts and washers, check nuts of galvanized steel including 15mm dia light grade upto 1.5 mtr below GL for protection pipe, excavation and earth work, charcoal dust, common salt, PCC 1:3:6 type C-1 chamber with cover and RCC 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 8mm dia TMT bars @ 75mm c/c both way with MS handle 12mm dia, PGI funnel and wire mesh all as shown in electrical plate No 5 of SSR Part-I connected to earthing test point all as specified including testing on completion all as directed .

Supply, laying and testing LT cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 Sqmm 4 core all as specified.

M&L for dry sand cushioning for protection of under ground cables (8 cm before laying the cable and 15 cm after laying the cable in trenches) all as specified.

M&L for well burnt sub class 'B', old size bricks laid dry, flat, over the cable abutting each other, length of brick equal to width of brick, all as specified.

S&F for point wiring with PVC sheathed stranded copper conductor cable 1.5 Sqmm FRLSH unsheathed copper conductor single core multi stranded cable 650/1100 volts grade drawn into and including non mettalic rigid PVC conduit medium grade drawn on surface with all fittings (ISI) marked not less than 20mm bore fixed concealed/recessed on wall/ceiling etc including 1.5 Sqmm FRLSH PVC insulated including mild steel sunken pressed steel terminal boxes of suitable size made of sheet 1.6 mm thick with 3 mm thick bakalite sheet top cover for one bell/ buzzer point controlled by one bell push complete all as specified.

S&F for sub main wiring of 1100 volts grade heavy duty two single core 4 Sqmm size (nominal area) PVC insulated (FRLS) copper multi-stranded conductor cable drawn into & including PVC conduit medium grade not less than 25 mm dia including its all accessories & fittings, fixed concealed with and including chase cutting and making good the existing surface along with a continuous run of 4 Sqmm size (nominal size) stranded copper conductor PVC insulated (FRLS) (green colour) cable as earth wire complete all as specified and directed. (NOTE: - TWO SINGLE CORE CABLES ALONG WITH EARTH WIRE AND PVC CONDUIT SHALL BE MEASURED AS ONE UNIT LENGTH).

S&F wall / surface mounted type LED light fitting batten type complete with LED lamp 10 Watt (2 feet long), poly carbonate body and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with twine core twisted flexible copper conductor cable complete all as specified.

S&F for air ventilating fan 300 mm sweep PVC body, AC, single phase, 230 volts, 1200 RPM complete and making holes with lovoured shutters including mounting frame and connecting the fan to ceiling rose including provision of three core flexible copper conductor cable of size 1.5 sqmm copper including to inside out surface & white wash etc with not less than 0.5 mtr long to connection complete all as specified.

S&F for switch Bell push,flush type 5 Amp, SP, 240 volts complete all as specified.

S&F for buzzers, ding dong AC 230 volts single pole all as specified.

S&F for flush mounting factory made Ekinoxe SPN DB's Double door, IP-43 Protection, IK-09 with metal door, with neutral bar, Earth bar and cables ties for cable management fully insulated bus bar 4 way with 100 Amps rated bus bar complete all as specified.

S&F for MCB SPN, 240 volts, 32 Amp, breaking capacity 10 KA, ‘C’ series all as specified.

S&F for 50 mm bore galvanished iron tubes, meduim grade with all fitting and laid in trenches all as specified and directed.

S&F for 50 mm bore gun-metal, globe or gate valves, class-I, 1.5 Mpa with ISI marked with iron wheel head, screwed both ends for iron pipe and fixed all as specified.

S&F for S&F for 20 mm bore galvanished iron tubes, meduim grade with all fitting and laid in trenches/ floor/ duct includign cutting pipe, screwing and making forged ends on piping as required all as specified and directed.

S&F for for 20 mm bore gun-metal, globe or gate valves, class-I, 1.5 Mpa with ISI marked with iron wheel head, screwed both ends for iron pipe and fixed all as specified.

M&L for cutting of existing pipe line 100 mm bore (CI/ DI) and insertion of Tee including CI/ DI special and earth work complete.

M/s Agarwal Builders (BID ID -3451460)

ZAIGHAM ENTERPRISES (BID ID -3461187)