Construction of NA-II Twin Quarter at Pudimadaka Lighthouse Station.

Amount

Jungle clearence including uprooting of rank vegetation, grass, brush wood,trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. including cost of all labours, tools & plants and all other charges etc., complete.

Earth work in excavation by mechanical means All kinds of soil (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in charge.including De-watering,Dressing sides, removal of loose soil at bottom, watering , ramming at bottom and as directed by Engineer-incharge. including cost of all labours, tools & plants and all other charges etc., complete.(levels should be done by Dumpy level instruement before start excavation and after excavation work)

Providing and laying in position Cement Concrete in foundation bed with 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) All work up to plinth level including laying, mixing,compacting, curing as directed by the engineer in charge including cost of all materials, labours, tools & plants,curing,safety measures and all other charges etc., complete.

Providing and laying in position ready mixed or site batched design mix M30 grade cement concrete for reinforced cement concrete work with minimum cement content of 350 kg/cum ; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level (Foundation)Concrete of M30 grade with minimum cement content of 350 kg /cum

All works above plinth level upto floor V level (Super structure-lintel & column /Sunshades/Chajja/roof slab.,etc.)Concrete of M30 grade with minimum cement content of 350 kg /cum

Add extra cement over specified Design mix (aprx. 60kg/Cum)

Providing Steel reinforcement Fe-500D of approved brand (SAIL, TATA TISCON, VIZAG STEEL ) for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level and above plinth level of tested Tor steel reinforcement of approved 1st quality as per drawing and as directed at all heights including cost of all labour, materials, tools & plants,safety measures and all other charges etc., complete.

Providing & Laying of Dry stone pitching 230 mm thick under floors, ramps,septic tank as per drawing and wherever directed with approved quality stone, by proper hand packing, consolidation by rolling/ramming as required filling interstices with spalls and sand all as per standard specifications and as directed, consolidating to required gradient and camber, watering including cost of all labour, materials, tools and plants, safety measures and all other charges etc., complete.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.Including supply of all material,labours, tools & plants safety measures and all other charges etc., complete.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. as per drawing and as directed at all heights including cost of all labour, materials, tools & plants,curing,safety measures and all other charges etc., complete.

For foundation & plinth

For super structure above plinth level upto floor V level

Half brick masonry Cement mortar 1:3 (1 cement :3 coarse sand) with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.as per drawing and as directed at all heights including cost of all labour, materials, tools & plants,curing,safety measures and all other charges etc., complete.

Providing of Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete, Suspended floors, roofs, landings, balconies and access platform, Columns, Pillars, Piers, Abutments, Posts and Struts and Stairs, including cost of all labour, materials, tools & plants ,safety measures and all other charges etc., complete.

Foundations, footings, bases of columns, etc. for mass concrete

Columns, Pillars, Piers, Abutments, Posts and Struts.

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Shelves (Cast in situ)

Suspended floors, roofs, landings, balconies and access platform.

CEMENT PLASTER WITH A FLOATING COAT OF NEAT CEMENT

20 mm thick cement plaster with CM 1:3 of brick masonry surfaces and Concrete surfaces for Eexterior plastering up to floor two level, including and finished even and smooth in CM 1 : 3.as per standard specification and as directed at site including supply of all material,labours,scaffolding,curing, tools & plants,safety measures and all other charges etc., complete.

15 mm thick cement plaster with CM 1:3 of brick masonry surfaces and Concrete surfaces for Interior plastering for walls as per standard specification and as directed at site including supply of all material,labours,scaffolding,curing, tools & plants,safety measures and all other charges etc., complete.

12 mm thick ceiling plaster with CM 1:3 of brick masonry surfaces and Concrete surfaces for Interior plastering for walls as per standard specification and as directed at site including supply of all material,labours,scaffolding,curing, tools & plants,safety measures and all other charges etc., complete.

6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams.as per standard specification and as directed including cost of all labour, materials, scaffolding, tools and plants, curing,safety measures and all other charges etc., complete.

Providing Second class teak wood work in frames of doors, windows, clerestory windows,ventilator and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). complete as per design approved by Engineer-in-Charge.Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & Jointed with self driven self tapping screws of size 38 mm x 4 mm & PVC solvent cement, including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturer's specification and direction of Engineer-in-charge.Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing & fixing of wooden Shutters for doors and windows

Providing and fixing of Second class teak wood 35 mm thick panelled or panelled and for doors fixing with butt hinges of required size with necessary screws, including panelling, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and fixing 35 mm thick ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. including ISI marked Stainless Steel butt hinges with necessary screws.Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and fixing 30 mm thick shutters panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)

Providing and fixing factory made 30 mm thick Non decorative finish door shutter made of solid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mm x 1 mm, painted with primer , all four corners of reinforcement to be welded or sealed. Solid PVC extruded bidding (push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rail of size 100 mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100mm x 8 mm complete as per manufacturer's specifications and direction of Engineer-in-charge.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etc.all complete as per direction of Engineer-in-charge. including cost of all materials, labours, tools & plants and all other charges etc., complete.including cost of all materials, labours, tools & plants and all other charges etc., complete.

Providing & fixing 5.5 mm thick glass louver panes with putty and glazing clips in steel doors, windows, clerestory windows,ventilator,louvers all complete . including cost of all materials, labours, tools & plants,safetty measures and all other charges etc., complete.

Providing and fixing in position (as per 1868/1982) Alluminium sliding window of three tracks with rectangular pipe 95x38.10x0.90 millimetre at weight 0.637 kg/mtr. with window frame bottom track section 92x31.75x1.30 mm at weight 10.70kg/mtr. Top and side track section 92x31.75x1.30mm at wight 0.933kg/mtr. The shutter should be of bearing bottom 40x18x1.25mm at weight 0.417kg/mtr. inter locking section 40x18x1.10mm at weight 0.469kg/mtr. and handle and top section 40x18x1.25 mm at weight 0.417kg/mtr. as per detailed drawing and as directed by Engineer incharge with all necessary Aluminium section fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted verticle section of shutter including 5 mm thick high performance single glaze unit (SUG)-glass aluminium mosquito net shutter with stainless steel jali with all required screws and nuts etc. complete. with colour anodising with box.including cost of all materials, labours, tools & plants,safetty measures and all other charges etc., complete.

Providing of fittings & fixtures for door of heavy duty with C.P. brass screws and as directed including cost of all materials, labour, tools & plants and all other charges etc. complete.

Providing and fixing 300x16x5 mm bright finished brass door latch (aldrop) with necessary screws etc. complete :Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and fixing bright finished 250x10 mm brass tower bolts (barrel type) with necessary screws etc. complete. Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and fixing 125mm chromium plated brass handles with necessary screws etc. complete: Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and fixing bright finished 125x85x5.5 mm (heavy type) brass butt hinges with necessary screws etc. completd.Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and fixing 300x10 mm aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 transparent or dyed to required colour or shade, with necessary screws etc. complete :.Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and fixing 125 mm aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and fixing 125x90x4.00 mm ISI marked, IS : 1341, M.S. heavy weight butt hinges with necessary screws etc. complete :.Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and fixing 300x20x6 mm ISi marked oxidised M.S. door latches (aldrop) conforming to IS:5930 with necessary screws etc. complete :.Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete. Including supply of all material,labours, tools & plants and all other charges etc., complete.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth as directed by the engineer in charge including cost of all materials, labours, tools & plants,laying, compacting, curing and all other charges etc., complete.

Providing and fixing 610x510 mm bowl depth 200 mm for Kitchen sink without drain board Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and fixing 600x600mm 1st quality vetrified tiles of 10 mm thick for flooring and Skirting (Bell/ Kajaria/ Johnson) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete including supply of all labours, tools, materials and finishing etc. complete as directed by the engineer in charge.

Providing & laying of Anti- Skid Ceramic floor tiles for Bath and Glazed wall tiles for Toilets

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. including supply of all labours, tools, materials and finishing etc. complete as directed by the engineer in charge.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.ncluding supply of all material,labours, tools & plants and all other charges etc., complete.

Providing edge moulding to 18 mm thick Granite work marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. complete at all levels.ncluding supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered Outside and inside of building wall surface to prepare the surface even and smooth complete. complete as per design approved by Engineer-in-Charge.Including supply of all material,labours, tools & plants and all other charges etc., complete.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)as directed by enginner incharge including cost of all labour, materials, scaffolding, tools and plants,and all other charges etc., complete.

Providing and Finishing walls with 100% Premium acrylic emulsion paint for interior wall/ceiling surfaces having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. of New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. as directed by enginner incharge including cost of all labour, materials, scaffolding, tools and plants,and all other charges etc., complete.

Providing and applying French spirit polishing: Two or more coats on new works including a coat of wood filler. including cost of all labour, materials, scaffolding,scrapping, tools and plants,and all other charges etc., complete.

Providing and applying Painting with synthetic enamel paint for Steel Surfaces of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. including cost of all labour, materials, scaffolding, tools and plants etc., complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. including cost of all labour, materials, scaffolding, tools and plants,and all other charges etc., complete.

20 mm dia CPVC pipe

25mm dia CPVC Pipe

32mm dia CPVC Pipe

40mm dia CPVC Pipe

Providing and fixing (6kgf/cm2) on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.including cost of all labour, materials, tools and plants,and all other charges etc., complete.

110mm Dia

75mm Dia

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc..as per direction of Engineer in charge.including supply of all labours,materials, tools & plants,Fittings unions,tees,bends,Offsets,nipples,couplers,safety measures and all other charges etc., complete.

25 mm dia nominal bore

32 mm dia nominal bore

Providing and fixing PVC fittings of heavy duty, approved first quality and brand (SUDHAKAR/ PRINCE/ASHIRVAD/SUPREME) accessories like elbow, Tee, Bend,Reducers etc.,. Including Supply of all materials, labours, tools and plants and all other charges etc., complete.

P/F.110 mm dia PVC "elbow"

P/F.110 mm dia PVC "TEE"

P/F.110 mm dia PVC Bend / offset

P/F. PVC Reducer 110 mm x 75 mm:-

P/F 110 mm dia PVC Floor Trap with screen

P/F 110 mm dia PVC Slotted vent cowl

P/F. PVC 110 mm dia door bend

P/F. PVC Door bend 75 mm dia

P/F. PVC 75 mm dia plain bend

Providing and fixing water supply fittings ( MAKE JAGUAR/CERA) with all necessary fixtures and specials of approved first quality brand/manufacturer,colour (ISI make) as per the following items including cost of all materials, labours, tools & plants and all other charges etc complete.

Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock conforming to IS standards and weighing not less than 810 gms.

Providing and fixing 15mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931.

P/F CP Brass 15 mm dia Pillar cock

Providing and fixing 15 mm nominal bore C.P. brass stop cock (concealed) of standard design and of conforming to IS:8931.

Providing and fixing 150 mm diameter C.P. brass shower rose with 15 or 20 mm inlet

P/F. PVC 15 mm dia Flexible connection pipe for W.Basin.

P/F 20 mm nominal bore ball valve (brass) of approved quality, High or low pressure, with plastic floats complete.

P/F 25 mm nominal bore ball valve (brass) of approved quality, High or low pressure, with plastic floats complete.

P/F 40 mm dia non return valve nominal bore

P/F CP waste coupling with 32 mm dia pipe

P/F of hindware health faucet (full set) with 1.2m SS flexible Tube & ABS wall hook (C.P BRASS) with fixing to 2 in 1 C.P brass angle valve for basin mixer and geyser points of approved quality confirming to IS:8931 for 15mm Nominal bore including fixing in position all as directed including supply of all materials, labours, Screws, tools& plants,safety measures and all other charges etc., complete.

Providing and fixing 32 mm dia P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing bath room fittings of approved first quality brand/manufacturer, colour /size like Mirror, Towel rail, Soap dish tray with all necessary fixtures including supply of all materials, labours, Screws, tools and all other charges etc., complete.

Providing and fixing 600x450 mm beveled edge mirror of superior glass ( Make approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. each including supply of all materials, labours, Screws, tools and all other charges etc., complete.

CP brass soap dish - 100 mm (Make approved quality)

CP brass Towel rail 20 mm dia 600 mm Long (Make approved quality)

C.P.Brass towel ring with concealed fittings arrangement of approved quality and colour, where ever necessary

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend,make (Make Parryware,hindware) overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid. Including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and fixing wash basin size 630x450 mm with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern,(Make Parryware,hindware) including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin with a pair of 15 mm C.P. brass pillar taps.including supply of all material,labours, tools & plants and all other charges etc., complete.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. including cost of all materials, labours, tools & plants and all other charges etc., complete.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 .including excavation supply of all material,labours, tools & plants and all other charges etc., complete.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design.Inside dimensions 455x610 mm and 45 cm deep for single pipe line.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.Including supply of all material,labours, tools & plants and all other charges etc., complete.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment including the cost of chemical emulsion including cost of all labour, materials, tools & plants etc., and other charges complete.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration including supply of all labours, tools, finishing etc. complete as directed by the engineer in charge.

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc., With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration. including supply of all labours, tools, finishing etc. complete as directed by the engineer in charge.

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20% including supply of all labours, tools, finishing etc. complete as directed by the engineer in charge.

Providing & laying roof edges for Staff Qtrs with CM 1:3 Add for plaster drip course/patty/ groove in plastered surface or moulding to R.C.C. projections. including supply of all material,labours, tools & plants and all other charges etc., complete. including, mixing, laying etc.,necessary scaffolding and necessary water proofing compounds, curing,safety measures and all other charges etc., complete.

G CHINNAMNAIDU

ASR CONSTRUCTIONS