A.R and M.O of HPPWD A.E. office building Nankhari in Tehsil Nankhari Distt. Shimla H.P.

Amount

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer- in- charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing ISI marked decorative flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless sqm Steel butt hinges with necessary screws ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing cup board shutters 19 mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16mm ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge. (ii)150 X 10 mm size.

Providing and fixing aluninium handles, ISI marked, anodised (anodica coating not less than grade AC 10 as per IS : 1868) transpoarent of dyed to required colour or shade, with necessary screws etc. complete including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge. (i)125 mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying Full body vitrified floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 1st quality ceramic glazed tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade complete including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing anf fixing pine wood strips in cealing (frames, backing or studding to be paid separately) with necessary fitting arrangements complete including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 9mm thick ply wood with necessary fitting arrengement complete including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 18 mm thick gang saw cut,mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills,facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment,epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc .complete at all levels: Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble :Area of slab over 0.50 sqm ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing specified wood frame work consisting of battens of 2.5cmx3.5cm size fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete :Kiln seasoned and chemically treated hollock wood .

Providing and fixing in wall lining/panneling with pine wood including back side strip of 12mm thick ply and poly sheet with necessary fixing arrangement and screws etc. complete : ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

French spirit polishing :Two or more coats on new works including a coat of wood filler ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing WI-Paraquit or action tesa clip in prelaminated wooden flooring (H.D.F) with poly sheet & thermocoal sheet with door profile and side moulding locks with all fittings ,etc. complete. ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately), with in all leads and lifts as directed by Engineer-in- Charge.: Second class Deodar wood.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately):Second Class Deodar wood, 35mm thick shutters.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :35 mm thick 2nd class deodar shutters with ISI marked M.S. pressed butt hinges bright finished of required size . ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 8 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessaryholes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 15 mm nominal bore ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge. Concealed work, including cutting chases and making good the wall etc.1620 (20 mm OD) pipe ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :White Vitreous china Anglo Indian Closet No. 2061 of size 550x460 mm of CERA or equivalent ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: Wash basin No.1012 or CERA or equivalent. ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing white vetrious china flat black wall conner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively with divider and necessary fitting including pipe, contoler complete including hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete 25 to 40 mm nominal bore) ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete) ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms ) ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.32 mm dia. ) ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms 15 mm nominal bore ) ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PTMT pillar cock of approved quality and colour 15 mm nominal bore, 107 mm long, weighing not less than 110 gms ) ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

Providing & fixing 100mm dai C.P. gratings of superior quality for floor, gully or nahani trap including carriage of materials within all leads & lifts ) ncluding hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge.

GM Industries