SPECIAL REPAIRS TO BUILDING NO. P-41A UNDER SPECIAL REPAIR B/R, PROVISIONING OF DRYING AND IRONING ROOM NEAR OFFICERS MESS (P-41A) UNDER LBW, PROVISIONING OF DEFICIENT BAGGAGE ROOM FOR INLIVING OFFICERS UNDER LBW AND PROVISION OF PROTECTIVE WORK NEAR

Amount

Dismantling asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified and as directed by the Engineer-in-Charge.

Demolition of old cement concrete of any description and in any position not otherwise specifically provided for (unreinforced) and removing debris from site of work complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles portions complete all as specified and as directed by the Engineer-in-Charge.

Taking down door chowkhat with shutter area n. exc 1.5 Sqm each(with taking off shutters from the frame)and removing to store complete all as specified and directed.

Taking down shutters of any description exc. 1 Sq.m. but n. exc. 2 Sq.m. each complete all as specified and as directed by the Engineer-in-Charge.

Taking down cement plaster of any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc built in cement mortar complete all as specified and as directed by the Engineer-in-Charge.

Surface excavation n. exc. 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and as directed by the Engineer-in-Charge.

Excavation in trenches n. exc.1.5m wide and n. exc. 1.5m in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n. exc. 10 Sq.m. on plan and n. exc. 1.5m in depth and getting out in any type of soil complete all as specified and as directed by the Engineer-in-Charge.

Excavation in trenches n. exc.1.5m wide and n. exc. 1.5m in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n. exc. 10 Sq.m. on plan and n. exc. 1.5m in depth and getting out in hard/dense soil complete all as specified and as directed by the Engineer-in-Charge.

Excavating over areas, n. exc. 1.5m deep and getting out in any type of soil complete all as specified and as directed.

Removing excavated soil to a distance not exc. 50m and depositing where directed at a level n. exc. 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

Removing excavated soil to a distance exc.1.5km but not exceeding 5 km and depositing where directed at a level n. exc. 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm. complete all as specified and as directed by the Engineer-in-Charge.

Removing excavated soil to a distance exc. 250m and but not exc.500m depositing where directed at a level n. exc. 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

Removing excavated rock to a distance exc. 250m and but not exc.500m depositing where directed at a level n. exc. 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

Dismantling water tanks of any description of capacity exc.250 Litres but n. exc. 500 Litres capacity complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 15mm dia. steel tubing and connections including for refixing or removal from site complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 20mm dia. steel tubing and connections including for refixing or removal from site complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 25mm dia. steel tubing and connections including for refixing or removal from site complete all as specified and as directed by the Engineer-in-Charge.

M&L for cutting steel tubing of existing GI pipe line 40/25 mm bore for alteration and addition and insert new Tee for branch connection complete all as specified and as directed by the Engineer-in-Charge.

S&F 25mm dia. GI water tubing 'medium grade' conforming to IS 1239 (Part-I) with all fittings such as bends, tees, short pieces, connectors elbows, reducers, unions, sockets etc., and laid in trenches, including testing complete all as specified and directed by the Engineer-in-Charge.

Taking down PVC (SWR) pipes of any radius including joints etc dia complete all as specified and as directed.

S & F PVC (SWR) pipes 40 mm dia in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S & F PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S & F PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) multiple floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F 40/50mm dia. PVC waste pipes for WHB/sink fixed to walls including fittings and connecting to multiple floor trap complete all as specified and as directed by the Engineer-in-Charge.

S&F pre- painted aluminium zinc corrugated steel sheet (galvalume base) of thickness 0.5mm, in colour having tensile strength of 550 Mpa as in roof covering/Cladding to wall and profile as approved by GE and to be factory moulded and fixed with hot dipped galvanised (not less than 150 gm/sqm) with high durable protective triple coated self tapping screws/self drilling screws, to suit the roofing in customized colour matching with the colour of roof covering / cladding to wall and screws are to be fixed using torque adjustable electronic gun screws driller of suitable capacity complete all as specified and as directed.

S&F pre painted galvalume aluminium zinc coating (zinc coating not less than 150 gm/Sqm) GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed.

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St-240 including painted one shop coat of zinc chromate prime paint including preparation of surfaces at the height of second floor roof complete all as specified and as directed.

S&F framed work such as grills, grating, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars, barred iron doors, ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and as directed.

S & F plates plain or chequered channels square cut or notched (Ordinary and counter sunk) forming holes with riveted bolted, or welded attachment conforming Fe-410 W (Gde-E-250) quality- A complete all as specified and as directed.

S & F 12mm dia mild steel screw bolts (machine made) with hexagonal or square heads at one end and secured the other or screwed the both ends each screwed ends to be fitted with washer and one hexagonal or square nuts n.exc 5cm long complete all as specified and as directed.

M&L for post construction anti termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia. holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed by the Engineer-in-Charge.

M&L for post construction anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/ hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same

M&L along the external wall below concrete or masonry apron using chemical emulsion @2.25 litres per linear metre including drilling and plugging holes etc in apron complete all as specified and as directed.

M & L for treating the backfill in contact with the foundation at the rate of 7.5 Ltrs of anti termite emulsion per Sqm of vertical surface complete all as specified and as directed.

M&L for treating the soil under plinth protection @ 5 ltrs of emulsion per Sqm of surface area complete all as specified and as directed.

M&L for second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with 6mm thick teak wood beading all round complete all as specified and as directed by the Engineer-in-Charge.

S&F for 35mm thick Plain, framed, panelled shutters of 2nd class hard wood (two panel), with lock rail and panels of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces, the size of rail and style as per IS : 1003 (part-I), kiln seasoned chemically pressure treated complete all as specified and directed.

S&F 30mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc, sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), supplied and fitted to chowkats complete all as specified and as directed by Engineer-in-Charge.

S&F 125mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed by the Engineer-in-Charge.

S&F 125mm size stainless steel butt hinges, medium weight, complete all as specified and as directed by the Engineer-in-Charge.

S&F 200mm size aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed by the Engineer-in-Charge.

S&F 150mm long extruded aluminium alloy handles, cast type, anodised complete all as specified and as directed by the Engineer-in-Charge.

S&F 300mm long aluminium alloy, anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F 150mm long floor door stopper of stainless steel alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed by the Engineer-in-Charge.

M&L for brickwork with fly ash bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

M&L for brickwork with fly subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 10mm thick with CM 1:6 on fair faces of brick work or concrete surfaces, finished fair and even complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 10mm thick with CM 1:3 using water proofing compound on fair faces of brick work or concrete surfaces, finished fair and even complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 10mm thick with CM 1:4 on fair faces of brick work or concrete surfaces, finished fair and even with out using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 10mm thick with CM 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L 15 mm thick rendering on fair faces of brick/concrete surfaces in cement mortar 1:4 in two layers of 10mm thick, finished even and smooth without using extra cement with using water proofing compound to cement mortar in outer layer only as per manufacturers instructions complete all as specified and directed. (Note:- WPC shall be measured and paid separately as supply only)

M&L for rendering 15mm thick with CM 1:3 on fair faces of brick work or concrete surfaces, finished fair and even with out using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 15mm thick with CM 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth with out using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for 5 mm thick rendering on ceiling surfaces in cement mortar 1:3 finished fair and even complete all as specified and directed.

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work n. exc. 15 cm in width or girth; including cutting to edges, all mitres and stopped ends, etc. complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper over one coat of primer on walls complete all as specified and as directed by the Engineer-in-Charge.

Supply only Integral Water Proofing Compound (ISI marked) of approved make.

M & L for preparation of new plastered surfaces of walls and applying two coats of interior emulsion over a coat of primer over a coat of wall care putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of weather proof exterior emulsion over one coat of primer complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of old plastered surfaces and applying one coat of oil bound distemper on walls complete all as specified and as directed by the Engineer-in-Charge.

M&L for complete removal of existing treatment on walls and applying two coats of weather proof exterior emulsion paint complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of old plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and as directed by the Engineer-in-Charge.

M&L for filling in floors or pavings,using earth from excavation laid in layers n. exc. 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed by the Engineer-in-Charge.

S&F anodised aluminium size of snap grid 605x605mm frame work for false ceiling complete all as specified and as directed

S&F 4mm thick non asbestos cement fiber board fixed to GI frame work for seamless ceiling complete all as specified and as directed.

S&F hangers 6mm dia GI (upto 1200mm length) adjoining level fixed in roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and as directed.

M&L for RCC M-30 design mix controlled concrete (Using 20mm graded granite stone aggregate) as in footings, plinth beams and the like complete all as specified and as directed by the Engineer-in-Charge.

M&L for RCC M-30 design mix controlled concrete (Using 20mm graded granite stone aggregate) as in columns and pillars complete all as specified and as directed by the Engineer-in-Charge.

M&L for RCC M-30 design mix controlled concrete (Using 20mm graded granite stone aggregate) as in lintel beams, roof beams and the like complete all as specified and as directed by the Engineer-in-Charge.

M&L for Reinforced Cement Concrete M-30 design mix controlled concrete (Using 20mm graded granite stone aggregate) in chajjas and the like complete all as specified and directed.

M&L for Reinforced Cement Concrete M-30 design mix controlled concrete (Using 20mm graded granite stone aggregate) in slabs supported on walls and the like complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed by the Engineer-in-Charge.

M&L for Reinforced Cement Concrete,1:1.5:3,type'A1 (Using 20mm graded granite stone aggregate) in foundations, including rafts, footings, plinth beams etc and the like complete all as specified and directed.

M&L for Reinforced Cement Concrete,1:1.5:3,type'A1 (Using 20mm graded granite stone aggregate) in columns,pillars,piers,posts and struts and the like complete all as specified and directed.

M&L for Reinforced Cement Concrete,1:1.5:3,type'A1 (Using 20mm graded granite stone aggregate) in beams,cantilevers,lintels over 1.5 m span. and the like complete all as specified and directed.

M&L for precast PCC 1:2:4 type B1 (Using 20mm graded stone aggregate) in kerb stones, window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone walling). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and set in cement mortar 1:4 complete with joints to match complete all as specified and as directed by the Engineer-in-Charge.

M&L for PCC 1:2:4 type B1 (Using 20mm graded stone aggregate) in benching, lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed by the Engineer-in-Charge.

M&L for precast RCC 1:2:4 type B1 (Using 20mm graded stone aggregate) as in landings, cover slabs (for manholes etc.), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M&L for broken stone or boulders in hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Crusher dust, sand filling,cusion bed for laying paver block complete all as specified and as directed by the Engineer-in-Charge.

S&F machine pressed precast concrete interlocking paver blocks of approved shape and size confirming to IS 15658-2006 of 60mm thickness and M-35 grade, with grey cement and pigments complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C1 (Using 20mm graded stone aggregate) as in plinth protection complete all as specified and as directed by the Engineer- in-Charge.

M&L for PCC 1:3:6 type C2 (Using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed by the Engineer-in-Charge.

M&L for concrete bed to drain pipes of size 160mm dia. including packing under and completely surrounding pipes with plain cement concrete 1:4:8, type D2 (40mm graded stone aggregate) after they are laid and tested complete all as specified and as directed by the Engineer-in-Charge.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including form, moulds, mitred/stopped ends etc complete all as specified & directed.

S&F 160mm dia. PVC underground drainage pipes, SDR 41, SELFIT, of pressure rating 4KN/Sqm confirming to IS 15328-2003, single socketed in any length jointed with solvent cement laid in trenches or floors etc complete all as specified and as directed by the Engineer-in-Charge.

Cutting into existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 150 mm bore drain pipe complete all as directed.

M&L plain cement concrete /RCC 1:3:6 type C-1 using 20mm graded stone aggregate as in coping including weathering slightly rounded or chamfered angle and throating including necessary form work complete all as specified.

M&L for 75mm thick PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in sub base for flooring complete all as specified and as directed by the Engineer- in-Charge.

M&L for 100mm thick PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in sub base for flooring complete all as specified and as directed by the Engineer- in-Charge.

M&L for 50mm thick PCC 1:2:4 type B1 (Using 20mm graded stone aggregate) as in sub base for flooring complete all as specified and as directed by the Engineer- in-Charge.

M&L for 40mm thick PCC 1:2:4 type B1 (Using 20mm graded stone aggregate) as in sub base for flooring complete all as specified and as directed by the Engineer- in-Charge.

M&L for 25mm thick PCC 1:2:4 type B1 (Using 20mm graded stone aggregate) as in sub base for flooring complete all as specified and as directed by the Engineer- in-Charge.

M & L for designer cement concrete tiles rubber moulded of size 300 x 300 x 25mm thick, set, jointed and pointed in neat cement slurry with grey and cement pigment in floors over a screed bed of 20mm thick in cement mortar 1:4 complete all as specified and directed.

M & L providing 40mm thick (measured solid), precast cement concrete louvers and jallies with 1:2:4 mix, type B0 (using 12.5mm graded stone aggregate) including all mouldings set in cement mortar (1:4) but excluding frame complete all as specified and as directed. (Note : Precast frame shall be measured and paid separately.)

M&L for anodised powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified (minimum thickness of powder coating 50 micron) complete all as specified and as directed by the Engineer-in-Charge.

S&F anodised powder coated aluminium window and ventilator shutters, sliding type without sash bars, aluminium sections including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws and suitable anodised aluminium handles and rollers complete all as specified (minimum thickness of powder coating 50 micron) complete all as specified and as directed by the Engineer-in-Charge.

S&F anodised coloured aluminium grill of design No.DG-117, 10mm thick of DECOGRIL or equivalent make as approved by GE fixed with and including 'F' sections complete all as specified and as directed by the Engineer-in-Charge.

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by the Engineer-in-Charge.

S&F 4.8mm thick plain sheet glass, ordinary quality and glazing with oil putty in square n. exc. 0.5 Sq.m. in each pane complete all as specified and as directed by the Engineer-in-Charge.

S&F 4mm thick figured glass, pin head type & glazing with oil putty including steel pin as in steel frame, in square n-exc. 0.5 sqm in each pane complete all as specified.

S&F solid PVC door frame of size 100mmx60mm made out of 5mm wood grain printed PVC sheet (Used instead of plain colour PVC sheet) and edges painted to match with the printed sheet, reinforced with mild steel square tube in opening as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge.

S&F solid PVC door frame of size 50mmx95mm made out of 5mm wood grain printed PVC sheet (Used instead of plain colour PVC sheet) and edges painted to match with the printed sheet, reinforced with mild steel square tube in opening as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame covered with heat moulded wood grain printed PVC sheet (used instead of Plain colour PVC sheet) with 5mm thickx15mm wide PVC sheet beading used inside stiles & rails and decorative PVC beading of 10mmx10mm (90O) used instead of exposed portion of PVC sheet beading, panelling of wood grain printed PVC sheet to fit in the mild frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge.

S&F 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed by the Engineer-in-Charge.

S&F 150mm size aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed by the Engineer-in-Charge.

S&F 125mm long extruded aluminium alloy handles, cast type, anodised complete all as specified and as directed by the Engineer-in-Charge.

M & L machine cut kota stone slab flooring 20 to 25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 15mm thick screed bed in CM 1:4 finished even and rough complete all as specified and as directed.

M&L machine cut polished kota stone slab 20-25 mm thick as in riser of steps, skirting, dado and pillar laid over 10mm thick cement screed bed in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade including rubbing and polishing complete all as specified.

S & F grating doom 125 mm dia with waste hole of PTMT (Min weight 40 gms) complete all as specified and as directed.

S&F Bib taps 15mm dia. fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F soap dish, chromium plated brass, of approximate size 160x160x90mm, fixed to plugs with chromium plated brass screws complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 15mm dia. chromium plated pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

S & F PVC flexible connections 15mm size with PTMT nuts of length 600 mm long complete all as specified and as directed.

S & F in repairs PVC flexible connections 15mm size with PTMT nuts of length 450 mm long complete all as specified and as directed.

S & F in repairs Brass chromium plated shower rose 125mm size complete all as specified and as directed.

S & F Brass chromium plated shower rose 125mm size complete all as specified and as directed.

S&F in repairs, tubular towel rail stainless steel, 20mm dia., 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, towel ring round with round flange of make Jaguar Catalogue No.ACN-1121BN or equivalent make as approved by GE complete all as specified and as directed by the Engineer-in-Charge.

S&F towel ring round with round flange of make Jaguar Catalogue No.ACN-1121BN or equivalent make as approved by GE complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 15mm dia. chromium plated angle stop valves, fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F 15mm dia. chromium plated angle stop valves, fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs 15mm bore dia Stop valves fancy type Chromium plated, concealed type with long shank and cup screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repairs two way bib cock 15mm dia. chromium plated, fancy type of make Jaquar Catalogue No.FON-40041 or equivalent in CERA complete all as specified and as directed by the Engineer-in-Charge.

S&F two way bib cock 15mm dia. chromium plated, fancy type of make Jaquar Catalogue No.FON-40041 or equivalent in CERA complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, health faucet 15mm dia. with one meter long easy flex tube in chromium finish and wall look of make Jaquar Catalogue No.ALD-CHR-565 or equivalent in CERA complete all as specified and as directed by the Engineer-in-Charge.

S&F Health faucet 15mm dia. with 1.5 m long easy flex tube in chromium finish and wall look of make Jaquar Catalogue No.ALD-CHR-565 or equivalent in CERA complete all as specified and as directed by the Engineer-in-Charge.

S&F 500 Litres capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) two layered ISI marked hoisted and fixed in position complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 25mm bore PP-R ball valves(brass insert) high pressure of PTMT (Minimum weight 142 gms) with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed including GI fitting complete all as directed.

S&F 20mm dia PP-R ball valves(brass insert) high pressure of PTMT (Minimum weight 142 gms) with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed including GI fitting complete all as directed.

S&F in repairs 25mm bore PP-R gate valves(brass insert) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed including GI fitting complete all as directed.

S&F in repairs, 25mm dia. gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F 25mm dia. gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F 25mm dia. chromium plated angle stop valves, fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the Engineer-in-Charge.

S & F 15mm bore Chromium Plated three in one wall mixer for mixing hot and cold water including provision for telephonic screwed down for iron pipe complete all as specified and as directed. Model No: QQT-7219 of Make :Jaquar

S & F 32 mm internal dia, 3-layer PP-R P o l y p r o p y l e n e random copolymer) pipes SDR 7.4 & SDR 11 UV stabilised and a n t i m i c r o b i a l welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded p o l y p r o p y l e n e random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and as directed.

S&F 25mm internal dia. 3-layer PP-R polypropylene random copolymer pipes SDR 7.4 & SDR 11 UV stabilised and antimicrobial welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 25mm internal dia. 3-layer PP-R polypropylene random copolymer pipes SDR 7.4 & SDR 11 UV stabilised and antimicrobial welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F 20mm internal dia 3-layer PP-R polypropylene random copolymer pipes SDR 7.4 & SDR 11 UV stabilised and antimicrobial welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 20mm internal dia 3-layer PP-R polypropylene random copolymer pipes SDR 7.4 & SDR 11 UV stabilised and antimicrobial welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, wash hand basin of size 550x400 vitreous China (flat back or angle back type) including half pedestal and cutting for and pinning in ends of brackets or erecting stand including supply and fixing of waste coupling, waste pipe etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F wash hand basin of size 550x400 vitreous China (flat back or angle back type) including half pedestal and cutting for and pinning in ends of brackets or erecting stand including supply and fixing of waste coupling, waste pipe etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs vitreous china wash down water closet of "Orissa" pattern size 580 x440mm white with integral foot rests including connection to trap and to flushing pipe anti syphonage pipe etc complete and making good to floor all as specified and directed.

S&F in repairs vitreous china wash down water closet of pedestal pattern size 580 x440mm white with integral foot rests including connection to trap and to flushing pipe anti syphonage pipe etc complete and making good to floor all as specified and directed.

S&F in repairs, 10 Litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32mm dia. and connection to pipes and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC (SWR) vent cowls 110mm dia. complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC (SWR) vent cowls 75mm dia. complete all as specified and as directed by the Engineer-in-Charge.

S&F 110mm dia. PVC (SWR) plain bends any radius with access door complete all as specified and directed by the Engineer-in-Charge.

S&F 75mm dia. PVC (SWR) plain bends any radius with access door complete all as specified and directed by the Engineer-in-Charge.

S & F 110 mm dia PVC (SWR) double 'Y' branch piece junction , single equal or unequal complete all as specified and as directed.

S&F in repairs PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed by the Engineer-in-Charge.

S&F PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed by the Engineer-in-Charge.

S & F in repair cast iron Nahani trap 125mm dia PTMT with grating including jointing to waste pipe in cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) complete all as specified and as directed.

M&L for non skid ceramic tiles 7 to 8mm thick area of each tile exc. 0.11 Sq.m. but n. exc. 0.18 Sq.m. (400x400mm size), in floors etc.set and jointed in neat slurry and pointed in white or coloured cement to match for joint free over screed bed or bedding layer 15mm thick in CM 1:4 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L for non skid/matt finish ceramic tiles 7mm thick area of each tile exc. 0.11 Sq.m. but n. exc. 0.18 Sq.m. (400x400mm size), in floors etc.set and jointed in neat slurry and pointed in white or coloured cement to match for joint free over screed bed or bedding layer 15mm thick in CM 1:4 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L for non skid/joint free ceramic tiles 7mm to 8mm thick area of each tile exc. 0.18 Sq.m. but n. exc. 0.38 Sq.m., in floors etc.set and jointed in neat slurry and pointed in white or coloured cement to match for joint free over screed bed or bedding layer 15mm thick in CM 1:4 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L for non skid/joint free ceramic tiles 7mm to 8mm thick size of each tile600mm X 100mm, in vertical surfaces(skirting) etc.set and jointed in neat slurry and pointed in white or coloured cement to match for joint free over screed bed or bedding layer 10mm thick in CM 1:4 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L for glazed ceramic tiles in vertical surface like skirtings dado etc., of size 350x250x7mm or 450x350x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match for joint free over backing of 10mm thick in CM1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed by the Engineer-in-Charge.

S & F in repairs stainless steel pipe 25mm dia Curtain rod for windows, doors opening etc complete all as specified and as directed.

S & F Fancy type chromium plated knobs for fixing curtain rod complete all as specified and as directed.

M & L for preparation of new wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel Paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel and Iron surfaces over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of old painted steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.

Use and waste of form work to sides of foundation/footings, plinth beams and similar work for rough finished surfaces complete all as specified and directed.

Use and waste of form work to sides of columns and pillars for fair finished surfaces complete all as specified and directed.

Use and waste of form work to sides and soffits of floor or roof beams,lintels,cantilivers,shelves including supports etc, for fair finished surfaces complete all as specified and directed.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floors slabs, landings and similar work, not exceeding 200mm thick for fair finished surfaces complete all as specified and directed.

Formwork to sides and soffits of chajjah,lintel,shelves of slab/ beams and similar work including supports, overhangs, etc finished rough surfaces of concrete flat complete all as specified and as directed.

M & L for TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

S&F reinforcement TMT steel bars 6mm to 8mm dia. cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia. or securing with clips or welded complete all as specified and as directed by the Engineer-in-Charge.

M & L for TMT steel bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L Complete for valve pit chamber of internal size 600x600x600 mm with full brick wall in cement mortar 1:4, over a foundation of 100 mm PCC 1:4:8 type B2 including MS sheet cover of 3mm thick including locking arrangement with two coat of synthetic enamel paint over a coat of red Oxide primer complete all as specified and as directed. NOTE:- Unit rate is deem to be included for plastering to internal surfaces of chamber and exposed surfaces of external wall with CM 1:3.

Material and labour for point wiring for one light controlled by one 05 amp one way modular switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including 20 mm dia (medium grade) rigid non metallic PVC concealed conduit along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly complete all as specified and as directed.

All as per item No. 181 here in before but for one fan/E fan point controlled by one way switch and regulator all as specified and as directed by Engineer- in- Charge.

All as per item No. 181 here in before but for one 3 pin switch socket outlet,5Amp on independent board all as specified and as directed by Engineer- in- Charge.

All as per item No. 181 here in before but for one switch socket outlet,5Amp on same board with other switches all as specified and as directed by Engineer- in- Charge.

All as per Item No. 181 here-in-before but for one16 Amp 3 & 5 pin switch socket outlet, independent with 4 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire all as specified and as directed.

S&F socket out let multipurpose 3 pin 15 amp and one 3 pin 5 amp controlled by and including one 15 amp switch all as specified and as directed.

S&F switch piano flush type single pole one way 5 Amps, 230 Volts, 50 Hz complete all as specified and as directed by the Engineer-in-Charge.

S&F switch socket outlet 5 pin 5 amp flush type with including switch all as specified and as directed.

S&F ceiling rose surface bakelite three terminals all as specified and as directed.

S&F Ceiling fan regulator electronic deluxe rotary step type all as specified and as directed.

S&F sheet metal enclosure for MCB DBs, phosphatised, Powder coated , single pole and neutral (SPN) 240 Volt , double door, suitable for 8 way with dim rail earth and neutral bar all as specified and as directed.

S&F in proper position MCB Double Pole of capacity up to 40 amps, 240 Volts C series with 10KA breaking capacity complete all as specified and as directed.

S&F MCB SP 6 to 32 amps, C curve 10 KA breaking capacity of 240 Volts complete all as specified and as directed.

S&F indoor luminare decorative batten for wall/ceiling mounting box type energy efficient saving LED BATTEN LIGHT 20W including twin twisted copper conductor flexible wire from ceiling rose to connector all as specified and as directed. Make:Havells Cat No. LHEXACP7IN1W020 or equivalent model in Philips/Wipro/Crompton.

S&F lamp holder insulated body suitable for Retrofit lamp all as specified and as directed.

S&F and fixing on wall security LED light fitting luminaire 1X25 W and including cable for connection from ceiling rose with 1.5 Sqmm PVC insulated stranded copper conductor (FRLS) cable including 25 mm GI bracket medium grade 1m long bent to shape including bolt,nut,washer,clamp etc all as specified and as directed by the Engineer-in-Charge.

S&F ceiling fan 1200mm sweep, BEE 5 star rated 380 Rpm with high air delivery at low voltages, with double ball bearing in ivory gold/white colour including fixing of regulator, down rod of 19mm dia 300mm long and connecting up with flexible 3 core 1.5sq.mm twisted copper cable from terminal point to ceiling fan complete all as specified and as directed by the Engineer-in-Charge.

S&F Exhaust fan wall mount type 300 mm sweep metal body Heavy duty , single phase with louver shutter and connecting up including provision of hold fasts for fixing fan and louver shutter with cutting of hole and necessary PCC(1:3:6) all as specified and as directed.

Supply and fixing AC single phase static Electronic KWH energy meter of accuracy class 1.0,240v,50Hz, with backalite LCD Display, of rating 10-60A with transparent hinged type Box with six month History of energy in KWH with taking down old meter and kept in MES store yard with accessories all as specified and as directed by the Engineer-in-Charge.

Supply and lay cable XLPE PVC insulated armoured, heavy duty electric power cable with aluminium conductor 1100 volts cross sectional area 16 Sqmm 2 core complete all as specified and directed.

Excavating over areas, n. exc. 1.5m deep for trench of FRLS Cable etc and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed.

Removing excavated material to a distance n. exc. 50m and depositing where directed at a level n. exc. 1.5m above the starting point complete all as specified and as directed.

Supply and spread clean river sand as cable cushioning for protection of cable to be laid in trenches all as per SSR part I complete all as directed by Engineer-in-Charge. Note: Punned thickness will be measured and paid.

Supply and lay bricks common burnt clay building bricks sub-class B of size 230x113x75 in cable trenches complete all as directed

M&L for galvanized iron tubing 25mm bore light grade with all fittings for protection of FRLS cable, laid in trenches/wall/floor including necessary clamps, bolt/nut complete all as specified and as directed. Note: Earth work excavation will be measured and paid separately.

M&L for earthing complete with 7.5m long CI pipe 80mm dia. with flanged ends, centrifugally cast, class A, in any length, joints with suitable stainless steel nuts and bolts and sufficient slot up to 7.5m length buried directly and preferably vertically in ground with top flanged ended 7m below ground level welded/ connected with GI strip 32x6mm size on the top edge of the flange to bottom edge of the flanged for earthing including filling the pit with charcoal common salt surrounding the earth pipe including drilling 400mm dia. bore in any strata of soil to lower the CI pipe complete all as specified and as directed by the Engineer-in-Charge. Note: The rate deemed to be included the earth pit chamber, CI cover and earth lead 32x6mm GI strip from earth pit to DB upto 7 mtrs. length and testing on completion.

SSV CONSTRUCTIONS