SPECIAL REPAIRS TO BATHROOM OF BLDG NO P322 AND ADDN ALTN TO EXTERNAL PAINT SCHEME OF WARDROOM MESS AREA AT INS VALSURA JAMNAGAR

Amount

Taking down cement plaster of any description including racking out joints, hacking for key scrubbing down with water etc and removal of entire debris as ordered outside MD land complete all as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of entire debris as ordered outside MD land complete all as directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for and removal of entire debris as ordered outside MD land complete all as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and removal of entire debris as ordered outside MD land complete all as directed.

Dismantling floor, hearth or wall tiling inluding cement mortar bedding (but not backing), stacking serviceable tiles at site and removal of entire debris as ordered outside MD land complete all as directed.

Dismantling wrought iron or mild steel work any description not otherwise provided for .and stacking at site complete all as directed,

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from frame) and stacking at site where directed.

All as per item 7 here-in-above, but exceeding 1.5 Sqm but not exceeding 4 Sqm each

M&L for plain cement concrete 1:2:4 type B1 using 20 mm graded granite stone aggregate as in cast in situ in cills and other similar bands, plinth courses, coping, padding and roof kerb including necessary form work, weathering slightly rounded, chamfered angles and throating complete all as specified and directed.

M&L factory made pre cast PCC 1:3:6, type C1 (using 20 mm graded granite aggregate) as in block masonry with solid blocks, exceeding 10 cm in width and setting in CM 1:4 complete all as specified.

M&L factory made pre cast PCC 1:3:6 type C1 (using 20 mm graded granite aggregate) as in block masonry with solid blocks or slabs, 10 cm thick (plain or interlocking joints) and setting in CM 1:4 complete all as specified.

M&L for PCC 1:2:4, type B0 (using 12.5 mm graded crushed granite stone aggregate) as in precast cement concrete louvres and jallies, 35 mm thick (measured solid), set in cement mortar 1:4 including all mouldings complete.

M&L for providing precast cement concrete Type B1 1:2:4 using 20 mm graded crushed stone aggregate in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry),string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in mortar complete with joints to match Set in cement mortar 1:4 complete all as directed.

M&L for lime concrete with graded stone aggregate Lime Mortar 1:3 as in sunken filling.

Cutting holes in brick works of size not exc half brick built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required including making good as per its original specification with out any extra cost complete all as directed.

Cutting chases in brick/ stone wall, pinning in, making good to facing where required and plastering in CM 1:4 to ends of edges of landing, steps, cills, lintels etc and cutting chases not exceeding 10 cm girth for concealed water tubing and making good cutting as per its original specfication complete all as directed.

Supply only Integral Water Proofing Compound (ISI Marked) of Make : CICO, Acco Proof, Impermo, Aqua flex as approved.

S&F Second class hard wood factory made kiln - seasoned, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints and fixed in position complete all as directed.

S&F 35 mm thick second class hard wood factory made plain framed panelled door shutter (any number of panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12mm thick veneered particle boards with commercial veneering on both face the size of rail and style as per IS - 1003 (Part I) kiln seasoned and chemically pressure treated and fixed to chowkats complete all as directed.

S &F 35 mm thick second class hard wood factory made glazed and skeleton shutter open rebated and prepared to receive glass, guage etc edge of framing plain chamfered or rounded fitted with cut and mitred beads and ribeted sash bars any numbers for securing guage etc size of members of shutter as specified in SSR Part I Section 8 clause 8.24 (a) supplied and fitted to chowkats.

S&F fibre glass reinforced plastic (FRP) door frames of three legged of cross section 90x45 mm having single rebate 32x15 mm to receive shutter of 30 mm thickness. The laminate door frame moulded with fire retardant grade unsaturated polyster resin and chopped mat. Door frame laminate of 2 mm thick and filled with suitable wooden block in all three legs. The frame shall be covered with fibre glass from all sides. Mild steel stay shall be provided at the bottom to steady the frame.

S&F 30 mm thick fibre glass reinforced plastic (FRP) paneled door shutter made with fire retardant grade unsaturated polyester resin moulded to 3 mm thick FRP laminated for forming hollow rails and styles with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings cast monolithically with 5 mm thick FRP laminated for panels.

S&F anodised aluminium powder coated (minimum thickness of powder coating 50 micron) frames and shutters for doors, windows and ventilators with one or more rebates including joining cleat for fixing etc. complete all as directed.

S&F 200 mm long aluminium, anodised, barrel tower bolt (ISI marked) of extruded section and fixed.

S&F 100 mm size butt hinges stainless steel (ISI Marked), medium weight approved.

S&F 150 mm size aluminium alloy handles (ISI Marked) fabricated type anodised and fixed.

S&F 300 mm long aluminium alloy, anodised sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F 300 mm size mild steel ordinary rat tail rod pattern springs in-cluding roller and roller plate complete all as directed.

S&F XPM design aluminium alloy wire mesh, 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples along with wooden beads.

S&F mild steel hold fasts of flats iron 25x5mm confirming to Fe 410-O or Fe 310-O and similar items.

S&F Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as directed.

S&F GI chicken wire mesh including fixing to wall for receiving a plaster.

S&F for mild steel nuts and bolts of 5-10 mm diameter, not exceeding 5 cm long provided with hole in each bolt for tightning of wire. Made with hexagonal or square head each screwed end to be fitted with wahers complete all as specified.

M&L for 10 mm dia fastner/anchor bolts 120mm long with nuts each, drilling holes in existing walls for fixing brackets complete all as specified.

M&L framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

S&F plain mild steel wire 4.00 mm dia, galvanised class 3, including straining and fixing to wood, concrete or steel posts and /or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line wire to be measured).

S & F 10 mm dia and over TMT bars cut to length bent to shape required cranking including bending , hooking ends etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per item No. 37 here- in – above but 5 mm dia and over upto 10 mm dia as in stirrups

S&F hard drawn steel wire fabric exc 4.00 kg per sqm in weight cut to lenghts, bend to shape required and welding to MS frame work complete.

S&F pre-painted galvalume (zincalume) aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coverings/ ridges/ cladding to walls fixed with self tapping screws as specified.

M&L for complete water proofing treatment to sunken floors and returning filling of sunken and repair are as under: (i) First layer of slurry of cement using 0.25 kg cebex 100 or equivalent mixed to 50kg bag of cement using pressure grouting with 40 psi pup after filling all joints/ cracks in CM 1:4 mixed with Nitobond SBR or equivalent @ 1 Liter per 50kg bag of cement. (ii) Providing and applying 1.5mm thick with two coats with interval periods of 6 hrs over substrate at a coverage rate 2 kg per sqm usin spray/ roller over a layer of water roof coating using Fosroc nitoproof 600 or equivalent over dry surfaces. (iii) Laying 200gms non woven geo textile membrane over nitoproof 600 coating with overlap sealed before providing screed bedding.

M&L for 40mm avg thick plain cement concrete 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in sunken floor and finished the even and smoth without using extra cement complete all as directed.

M & L for 75 mm thick plain cement conctere 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection/ path etc. finishing the surface even and smooth without using extra cement including forming joints and filing with bituminous filler material complete all as specified and directed.

M & L non-skid coloured ceramic tiles 300x300x7 to 8 mm thick (square/ rectangular), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all directed and specified.

M&L glazed ceramic designer tiles any shade or pattern as approved of size 600x300x7 mm thick, on verticals surfaces, set and jointed in neat cement slurry including 10 mm thick back coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all directed. (Note for item No 44 to 45 : i) Quoted rate is deemed to be inclusive of cement screed/ back coat. ii) Colour of tiles shall be got appproved before incorporation in the work)

M&L for machine cut kota stone slab of minimum size 550 x 550mm, 20-25 mm thick, as in floor laid over and including 15 mm thick screed bedding in cement mortar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing & mirror, polishing complete all as directed. (Note: Quoted rate is deemed to be inclusive of cement screed.)

M&L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick/ block masonry surfaces other than fair faces of brick work mixed with WPC as per manufacturer instruction, and finished the surface fair and even complete all as specified and directed. (Note : WPC measured and paid separately).

M&L for Rendering 20 mm thick in cement mortar 1:4 on brick or concrete surface mixed with WPC @ the weight of minimum 2% by weight of cement mixed or as per manufacturer instruction, and finished the surface even and smooth without using extra cement complete all as specified and directed. Note: WPC measured and paid separately.

M&L for rendering 15 mm thick in CM 1:6 on brick/ block masonry surfaces other than fair faces of brick work finished even and smooth without using extra cement complete all as specified.

M&L for rendering 10 mm thick in CM 1:3 on fair faces of brick work or concrete surfaces in ceiling finished even and smooth without using extra cement complete all as specified.

M&L for rendering 10 mm thick in CM 1:3 on ceiling surfaces of roof projection/ chajjas working height upto 9 mtr including provn of necessary scaffolding, safety belts etc complete all as specified and as directed. (Note: Quoted rate is deemed to be inclusive of working upto 9 mts heigh, necessary scaffolding, safety belt etc shall be arranged by the contractor without any extra cost to Govt.)

Three coats of white wash on newly plastered wall surface after necessary preparation of surface complete all as directed.

Three coats of white wash on newly plastered surface of ceiling after necessary preparation of surface complete all as directed.

M&L for preparation of old surfaces of wall including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc including cornices, pilasters etc (Plastered or unplastered surfaces) and applying three coat of white wash complete all as directed.

M&L for preparation of old surfaces of ceiling including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc including cornices, pilasters etc (Plastered or unplastered surfaces) and applying three coat of white wash of white wash complete all as directed.

M&L for preparing new plastered wall surfaces and applying two coats of oil bound distemper over a coat of 1 mm thick white cement based wall care putty complete all as specified.

M&L for complete removal of existing treatment and preparing old plastered or unplastered surfaces of wall and applying two coats of oil bound distemper over a coat of 1 mm thick white cement based wall care putty complete all as specified.

M&L for preperation of old surfaces of walls and applying one coat of oil bound distemper complete all as specified.

M&L for preparing newly plastered or unplastered surfaces of exterior walls and applying two coats of antifungal exterior emulsion weather proof paint (Apex) over a coat of exterior primer complete all as specified.

M&L for complete removal of existing treatment and preparing old plastered or unplastered surfaces of exterior walls and applying two coats of antifungal exterior emulsion weather proof paint (Apex) over a coat of exterior primer complete all as specified.

M&L for complete removal of existing treatment by mechanical means (any no of layers), Washing, rubbing down and stopping of distempered and painted surfaces of wall surfaces complete all as specified and as directed by Engineer-in-charge.

M&L for providing 1 mm thick wall care putty on prepared surface of walls/ ceilng applied as per manufacturers instructions and to the satisfaction of Engineer-in-charge complete all as directed.

M&L for application of one coat of primer with sealant properties using "Seal-O-Prime" or "weather coat exterior primer" (Berger make or equivalent in other makes) complete and allowed to dry overnight to receive first coat of emulsion paint over 1 mm thick wall care putty complete all as specified and as directed by Engineer-in-charge.

M&L for application of first coat of Exterior emulsion paint on primed wall surfaces using rollers made from foam or synthetic fibre, to get a smooth and tint free surface, all as specified and allowed to dry for at least 8 hrs/ overnight to receive second coat of emulsion paint complete all as specified and as directed by Engineer-in-charge.

M&L for application of second coat of Exterior emulsion paint on wall surfaces using rollers made from foam or synthetic fibres, to get smooth and tint free surface, all as specified and as directed by Engineer-in-charge.

M&L for two coats of 1st quality synthetic enamel paint over a coat of pink primer on new wooden surface of any description over 10 cm in width or girth including necessary preparation of new wooden surface complete all as directed.

M&L for two coats of 1st quality synthetic enemal paint over a coat of zinc chromate primer over any description of new steel surface over 10 cm in width or girth including necessary preparation of new steel surface complete all as directed.

M&L for one coat of first quality synthetic enamel paint of any description over 10 cm in width or girth on old painted steel surface after necessary preparation of surface complete all as directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beads or fixed to aluminium sections not exceeding 0.5 Sqm in each pane complete all as directed.

S&F 3 mm thick figured glass, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane complete all as directed.

Taking down old GI tubing 15 mm bore and connection including cleaning for re fixing stacking at site where directed .

All as per item No. 71 here-in-above but 20 mm bore of pipe - do -

Fixing only 15 mm bore GI tube medium grade with all fittings all new (ISI Marked) fixed to wall and ceiling or laid in floors making necessary connection and testing complete all as directed.

M&L for 15 mm bore steel water tubing medium grade (ISI marked) with all new fittings (ISI marked) fixed to wall and ceiling or laid in floors in repairs complete all as directed.

M&L for 20 mm bore steel water tubing medium grade (ISI marked) with all new fittings (ISI marked) fixed to wall and ceiling or laid in floors complete all as directed.

S&F gun-metal globe or gate valves with iron wheel head screwed box and both ends for iron pipe for 20 mm bore of pipe or union complete all as directed.

S&F in repairs 15 mm bore bib taps long nose with wall flange, fancy type, cast copper alloy, chromium plated, long shank screwed for iron pipe or for brass ferrule complete all as directed.

S&F in repairs two way bib taps with health faucet with 1.2m brass flexible tube of length as ordered and wall hook mounted type chromium plated for EWC.

S&F in repairs 15 mm bore long body 'U' shaped pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down highpressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as directed.

S&F in repairs 15 mm bore stop valve fancy type, cast copper alloy, chromium plated, with long shank and cup (concealed type) screwed down high pressure with cruntch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified.

S&F in repairs 15 mm bore angle cock, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as directed.

S&F in repairs brass chromium plated shower rose 125 mm dia with or wihout swivel joint, any size, including fixing to steel pipe or union.

S&F 550 mm x 400 mm size ( white), counter type vitreous china wash hand basin including cutting for and pinning ends of brackets or erecting stand, waste coupling & waste pipe complete all as directed.

S&F in repairs vitreous China squatting pan 'Orissa' pattern of size 580x440 mm white with integral foot rests water closet (Squatt pattern) including provision of lime concrete bedding with connecting to trap anti syphonage pipe including P trap (excluding flushing cistern and flush pipe) etc. including joint between flushing pipe and coket of WC complete all as directed.

S&F in repairs vitreous China ware wash down water closet pan (Pedestal Pattern) (EWC), white (excluding flushing cistern and flush pipe) with fixing bolt to floor and connecting pan to trap, pedestral pan and trap, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc complete all as directed.

Fixing only vitreous China ware wash down water closet pan (Pedestal Pattern) (EWC), (excluding flushing cistern and flush pipe) with fixing bolt to floor and connecting pan to trap, pedestral pan and trap, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc complete all as directed.

S&F in repairs vitreous China ware wash down urinal, bowl type of size 465 x 355 x 265mm with grating and union for discharge pipe with urinal spreader, providing and fixing plugs, bedding urinal against wall in CM (excluding flushing cistern, flush pipe and waste pipe) complete all as directed.

S&F in repairs plastic water closet seat, white, closed pattern with flat bottom, cover and mild steel chromium plated or aluminised hinging device complete all as directed.

S&F in repairs 10 liters capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet ball valve, float and handle including brackets and flush pipe of polyetylene of low or high density or 32 mm dia PVC connection pipe complete all as specified.

S&F PVC connection 15mm bore and 45cm long with two Nos of brass check nuts and washers complete all as directed.

S&F PVC waste pipe of suitable length for wash hand basin complete all as directed.

S&F 100 mm size PVC (SWR) multi floor trap with grating including jonting the same with solvent cement complete all as directed.

S&F in repairs soap dish, fixed to tiled walls with plugs and chromium plated brass screws complete.

S&F 75 mm bore high density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2, fixed to wall, ceilings or in floors etc. complete as directed.

S&F 100mm bore cast iron pipe, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors in repairs complete all as directed.

All as per item No 96 here-in-above but fixed to walls -do-

S&F 75mm bore cast iron pipe, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors in repairs complete all as directed.

All as per item No 98 here-in-above but fixed to walls -do-

S&F 100 mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as directed.

All as per item No 100 here-in-above but 75 mm bore bends -do-

S&F 100 mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval acess door complete all as directed.

All as per item No 102 here-in-above but 75 mm bore bends -do-

S&F in repair 100 mm bore cast iron branch pieces, Y, tee, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval acess door complete all as directed.

All as per item No 104 here-in-above but 75 mm bore branch pieces -do-

S&F 100 mm bore cast iron branch vent cowl complete all as directed.

S&F 75 mm bore cast iron branch vent cowl complete all as directed.

S&F 75 mm diameter of out let Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as directed.

S&F 75 mm size PVC (SWR) floor trap with grating including jonting the same with solvent cement complete all as directed.

S&F PVC (SWR) Gully trap 125/110 mm including jointing the same with solvent cement complete all as directed.

Dismantling of existing any type & any capacity water storage tank fixed in any description and stacking at site and S&F new 1000 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical vertical with close top) triple layer colour white both inside and outside with top cover including brass float valve high pressure suitable for 20 mm bore of pipe with polythene float, fixture hoisted and fixed in position where ordered and making necessary connection and testing complete all as directed.

E&M Items: Taking, down carefully copper/ aluminium point wiring (Light, Fan, socket or power) complete (fittings such as switches, celling roses, pendants, regulators, sockets, DB's) etc all as specified and directed.

Taking down carefully unserviceable Main switch and DB's including wooden board and removing from site including making good disturbed surfaces of wall all as complete as specified and as directed.

M&L for concealed type point wiring with 1100 V, 1.5 Sqmm single core PVC FRLS insulated unsheathed cable, copper conductor multistranded passing through including PVC concealed conduit 20mm, concealed MS box/ PVC/ MS/ Cast Iron box and logic modular whtie plates of suitable as required at site with PVC insulated unsheathed stranded copper of size 1.5 sqmm earth copper cable, for one light point, bell point, fan point controlled by one switch including cutting and making good surface of walls applying suitable painting as required all as directed.

All as per item No. 114 here-in-above, but for 6 Amp (2/ 3 pin), modular switch socket in same board with earth wire 1.5 Sq.mm PVC insulated multistranded copper conductor cable complete all as directed.

All as per item No.114 here-in-above, but for 6 Amp (2/ 3 pin), modular switch socket in independent board with earth wire 1.5 Sq.mm PVC insulated multistranded copper conductor cable all as directed.

All as per item No. 114 here-in-above, but size of cable 2.5 Sq.mm for 16 Amp and 6 Amp (3 pin) combined, modular switch socket in independent board with earth wire 2.5 Sq.mm PVC insulated multistranded copper conductor cable all as directed.

S&F in repair Modular switch 1 way 6 Amps,1 module all as specified and direced.

S&F in repair Modular switch 1 way 16 Amps,1 module all as specified and direced.

S&F in repair Modular Socket 6A -2/3 pin combinaed 2 Module all as specified and directed.

S&F in repair Modular Socket 16A -2/3 pin combinaed 2 Module all as specified and directed.

S&F in repair Ceiling rose surface bakelite White/ Ivory/ Urea finish 50 mm dia three terminals including supply and fix PVC square mounting block complete all as specified and directed.

Taking down existing light fittings fixed in any description and S&F new 20 Watt wall mounted 4 ft glaze LED batten CCT(K) 6500 high quality design aluminium extruded with decortive and caps fixed as per manufacturers instructions and making necessary electrical connections and testing on completion complete all as directed. Make: Jaquar Cat No. LGLZ01X020XC 20 W CCT 6500 or equivalent of Bajaj / Crompton / Philips / Wipro/ Havells.

Taking down existing light fittings fixed in any description and S&F new 10 Watt wall mounted 2 ft glaze LED batten CCT(K) 6500 high quality design aluminium extruded with decortive and caps fixed as per manufacturers instructions and making necessary electrical connections and testing on completion complete all as directed. Make: Jaquar Cat No. LGLZ01X010XC 10 W CCT 6500 or equivalent of Bajaj / Crompton / Philips / Wipro/ Havells.

S&F 300mm sweep metal Body Exhaust Fans AC single phase 230/ 240 V of size including taking down existing exhaust fan complete all as directed. Make: Bajaj Model No. Supreme Plus 300 mm 900 rpm Ind EX Fan Cat No 70069 or equivalent in Khetan/ Havells/ Orient. Note: Old exhaust fan shall be deposited in the AGE E/M store yard.

S&F sheet metal enclouser for DB'S in wall / Nitch when MCB's to be used Single pole and neutral, 8 way, Double door 240 Volt with 200 Amps rated Bus bar complete all as specified and directed.

S&F in repairs MCB SPN 32 Amp 240 V 50 Hz AC supply, 10 kA. Make: Legrand Cat No. 4086 17 or equivalent of Havells / L&T / ABB

S&F in repairs MCB SP 6 to 32 amp, 50 Hz, AC supply, 10 kA. Make: Legrand Cat No. 4085 92 to 4085 95 / Havells / L&T / ABB

Taking down existing submain wiring and M&L for concealed type submain wiring with two runs of single core 6 Sqmm PVC insulated unsheathed multi-stranded copper conductor cable drawing in and including PVC rigid medium grade conduit concealed of suitable size complete including provision of 6 Sq mm copper unsheathed cable PVC insulated as earthwire connected to earth doll inclusive of al tees, bends, elbows,reducers etc all as specified and directed. Note: 3 runs of 6 sqmm cable and one run of PVC concealed conduit shall be measured as one unit length.

M/s.Bhavin Electricals

M/s Balaji Enterprise