SPECIAL REPAIR TO BLDG NO EW 55 1 EW 55 2 AND EW 55 3 IN CENTRAL CAMPUS AND PROVN OF ALTERNATE GATE SENTRY POST FOR MT SEC CHAIN LINK FENCING AT POLO VIEW OFFICERS QTRS AND ADDN ALT TO BLDG NOEW 148 TO ACCOMMODATE CONTROL ROOM OF MT SEC AT IMA DE

Amount

M&L for vitrified ceramic tiles 10 mm thick polished,area of each tiles not exc 0.36 Sqm laid in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with and including 15 mm thick screed bed or bedding layer in CM 1:4 complete all as directed.

M&L for vitrified ceramic tiles 10 mm thick polished,area of each tiles not exc 0.36 Sqm fixed in vertical surface etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with and including 10 mm thick rendering in CM 1:3 complete all as directed.

M&L for glazed ceramic coloured tiles of size 350 mm x 250 mm x 7mm/ 450x350x7mm thick, as in vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match with and including 10 mm thick rendering in cement mortar 1:3 finished rough surface to receive tiles including dismantling of existing cement plaster complete all as directed.

M&L for rubberised polished chequered cement concrete coloured tiles 30 cm X 30cm X 25 mm thick, set, jointed & pointed in neat cement slurry in floor with grey cement & pigment to match the surface of tiles over & including 20 mm thick screed bed in CM 1:4 complete including dismantling of existing tiles with screed bed of any description and in any position complete all as specified and directed.

M&L for fibre reinforced heavy duty coloured cement concrete designer tile 25mm thick of any pattern as decided by Engr-in-charge as in floors/pavings laid over 15mm thick screed bed in CM 1:4 as base laid & jointed with white cement slurry mixed with pigment to match the shade of tile complete including dismantling of existing tiles with screed bed of any description and in any position complete all as specified and directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, coping, benching, kneelers, apex stone, bed plates, kerbs, etc. including weathering, slightly rounded or chamfered angles and throating, including necessary from work etc complete all as directed.

M&L for 75 mm thick PCC 1;3:6 type C-2 using 40mm graded stone aggregate as in plinth protection or similar places and finishing the surface even & smooth with out using extra cement including making joints 12mm wide to the full depth of PCC at every 3 meter and every change of direction and filling the same with mixture of bitumen & sand in ratio (1:1) by weight including necessary form work etc and including demolition of existing old cement concrete, complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation filling, mass concrete and sub base of floor etc including demolition of existing old cement concrete,complete all as specified and directed.

M&L for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete, all as specified and directed.

M&L for factory made decorative precast RCC M-25 balustered/ vertical post of 60cm height, sectional area not less than 225sqcm of required shape and size, medium duty of suitable thickness set in cm 1:4 including two coat of exterior weather proof paint over a coat of primer over 1.5mm thick wall care putty and dismantling existing wooden post complete all as specified and directed.

M&L for mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for 4mm thick E-board false ceiling (Classic) including galvanised colour coated snap grid frame for false ceiling, size of grid 605 X 605mm fixed with 1.6 mm dia GI wire suspenders one end tied to roof members and other end connected to main tee of grid framework size of main tee 38mm X 25mmX 1.4mm, cross tee 38 mm X 25 mm X 1.4mm, angle along walls 38 mm X 25mm X 2.0 mm complete all as directed

Taking down cement plaster on brick or stone walling built in CM including raking out joints hacking for key scrubbing down with water etc complete as specified

M&L for rendering 10mm thick plaster on concrete surface in CM (1:3) on ceiling finished even and smooth without using extra cement complete all as specifiied and directed.

M&L for rendering 15mm thick plaster on fair faces of brick work or concrete surface in CM 1:4 finished even and smooth without using extra cement and mixed with water proofing compound as per manufactures instructions, complete all as specified and directed Note- WPC will be measured paid as supply only under respective items separetely.

M&L for mild steel framed work such as grills, grating etc with end of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing framed work of water tanks and similar work including pintel hinges, stops hand made sliding bolts etc complete all as specified and directed.

M&L for welded steel wire fabric weight not exc 4 Kg/Sqm fixed to wood or steel members complete all as specified and directed.

M&L for 18/19mm thick colour PVC prelaminated board fixed to timber /mild steel frame as in cup board shutter / shelves, pelmet box and similar items fixed in repair complete all as directed as specified and directed.

S& F 100mm hasp and staple safety type aluminium anodised with MS hinge pin including bolt to hinge plate and fixed with screws complete all as directed.

S&F Continuous (Piano) hinges, mild steel, bright finished or electro galvanised, width of flap 30mm (when open), complete all as directed.

M&L for preparation of old plastered/un-plastered surfaces of wall by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots including cornices, pillar etc and applying one coat of white wash on walls complete all as specified and directed.

M&Lfor preparation of old plastered/un-plastered surfaces of ceiling by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots including cornices etc and applying one coat of white wash on ceiling complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil emulsion distemper on walls complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description, over 10 cm in width or girth and applying one coat of synthetic enamel paint with approved shade complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth and applying one coat of synthetic enamel paint with approved shade complete all as specified and directed

M&L for preparation of old plastered/unplastered surfaces of wall and applying one coat of weather exterior emulsion paint (Apex paint of Asian Paint / Weather proof of berger) on walls complete all as directed.

M&L for complete removal of existing treatment from wall complete all as specified and directed.

M&L for preparation of scrapped surface of wall / ceiling and applying Asian acrylic damp proof wall care putty in two coats as per manufacturer instruction complete all as specified and directed.

M&L for preparation of puttyied surfaces of wall and applying one coat of primer complete all as specified and directed.

M&L for preparation of primed surfaces of wall and applying two coats of Oil bound distemper complete all as specified and directed.

M&L for prepartion of surfaces and finishing walls with Acrylic Smooth exterior paint of required shade two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound emulsion over a coat of cement primer complete all as directed.

M&L for Preparation of new or previously untreated concrete/plastered wall surfaces of any description and applying three coats of white wash complete all as specified and directed.

M&L for Preparation of new plastered surfaces of ceiling and applying three coats of white wash etc complete all as directed.

M&L for Preparation of new surfaces of wall / ceiling and applying two coats of cement based paint including scaffolding complete all as specified and directed.

M&L for Preparation of new steel/iron surfaces of any description, over 10 cm in width or girth and applying two coat of synthetic enamel paint with approved shade over a coat of red oxide primer complete all as specified and directed.

Surface excavation n. Exc 30 Cm deep and averaging 15 cm deep and getting out in any type of soil complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and n' exc. 1.5 m in depth and getting out in any type soil complete all as specified and directed.

Excavation over areas n.exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in soil complete all as specified and directed.

Removing surplus excavated soil to a distance n.exc 50 metre & depositing where directed at a level n.exc 1.5 metre above the starting point complete all as specified and directed.

Spreading and levelling of soil obtained from excavation in layers not exceeding 25cm and well ramming including watering as required complete all as specified and directed.

M&L for Brick work with sub class B bricks, straight or curved on plan exceeding 6m mean radious built in cement mortar (1:4) complete all as specified and directed.

M&L for rendering 15mm thick plaster on brick work or concrete surface in CM 1:6 finished fair & even complete all as specified & directed.

M&L for RCC M -25 (Design Mix) using 20mm graded crushed stone aggregate as in foundations, including rafts, footing, foundation beams, plinth beams, bases for columns etc, basement slab, under-reamed piles and mass concrete etc complete all as specified and directed.

M&L for RCC M -25 (Design Mix) using using 20mm graded crushed stone aggregate as in column ,pillars, piers,posts and struts complete all as specified and directed.

M&L for RCC M -25 (Design Mix) using using 20mm graded crushed stone aggregate as in slab supported on walls beams and columns in floor, roof, landing and in shelves and the like complete all as specified and directed.

M&L for RCC M -25 (Design Mix) , type B-1using 20mm graded crushed stone aggregate as in beams, cantilever bressummers lintel over 1.5 m span etc complete all as specified and directed.

Use & waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick for fair finish surface complete all as specified and directed.

Use & waste for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter including fair finished surfaces complete all as specified and directed.

Use and waste of form work to edges of concrete slabs not exceeding 20 cm complete all as specified and directed.

Use and waste of formwork to sides and soffits of floors or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports etc. and similar work of fair finished flat surface of concrete complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified & directed.

M&L for Hard core of broken stone gauge not exceeding 63mm, deposited, spread and levelled in layer not exceeding 15 cm thick watered & rammed to a true surface complete all as specified and directed.

M&L for Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and incl either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering running rails and guides) and hanging; also fastening and fixing complete complete all as specified and directed.

S&F Cast iron work grade FG 150, machined, in pulley and similar articles not exceeding 5.00 Kg each complete all as specified and directed.

S&F MS work as in joist, angle or Tee section fixed independently without connecting plate complete all as specified and directed.

S&F MS work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles complete all as specified and directed.

M&L for 50mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in floors and finishing the concrete even and smooth using extra cement complete all as directed.

M&L fo Rolling and consolidating, formation surfaces (in cutting) with 8 to 10 ton power roller complete to reqd level, gradient, slopes, camber and super elevation including approved earth which may occur during rolling process complete all as specified and directed

M&L for Soling or sub base 150mm spread thickness with broken stone boulders, interstics filled surfaces formed and rolled and consolidated to required level camber gradient and super elevation with 8 to 10 ton power rollers complete all as specified and directed.

M&L for 75mm thick (compacted thickness) WBM, with coarse aggregates of grading 2 (63 to 40mm size) of lime stone, sand stone, flint or Quartzite stone, spread, watered, rolled and consolidated to gradient and camber required complete all as specified and directed.

M&L for Preparing of un-surfaced water bound macadam surface by brushing with wire brushes for removing caked mud etc. and sweeping with mechanical broomer and finally with air compressore to remove all loose dirt and applying even priming/tack coat with bituminious primer at @ 10 Kg/10 Sqm using VG-10 paving bitumen complete all as directed .

M&L for Premix bituminious macadam laid/rolled with power roller 8 to 12 tone roller and compacted to required gradient & camber (consolidated thickness 75mm or less) and binder content 4% (viscocity grade bitumen VG-30) by weight of total mix all as specified laid over priming/ tack coat. Note :- Preparing of surface and priming coat will be measured and paid for separate under relevant item)

M&L for Preparing of black top surface by brushing with mechanical broomer for removing caked mud etc. and sweeping with mechanical broomer and finally with air compressore to remove all loose dirt etc complete all as specified and directed.

M&L for Applying evenly a priming/tack coat with paving bitumen VG-30 @ 05 kg per 10 Sqm over black top surface complete all as specified and directed.

M&L for Bituminous premix asphaltic semi dense concrete 30mm avg consolidated thickness using VG-30 with 5.5% binder content by weight of total mix, rolled with 8 to 10 tonne power roller and compacted to required camber and gradient complete all as specified & directed by Engineer-in-charge.

Demolition of cement concrete in ground floors and pavings n. Exc 15cm thickness (below or above) ground level complete all as specified and directed.

M&L for Preparation of old plastered surfaces of walls by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of cement base paint on walls complete all as specified and directed.

Excavation in post holes each not exceeding 0.5 cum and getting out returning, filling in and ramming earth or broken rubble mixed with earth around in layers watering & removing surplus soil to a distance n.exc 50m & making good surface in any type soil complete all as specified and directed.

M&L for Brick work with sub class ‘B’ bricks (old size), straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

M&L for Brick work with sub class B bricks, straight or curved on plan exceeding 6m mean radious built in cement mortar (1:6) complete all as specified and directed.

M&L for Rendering 15mm thick plaster on brick work or concrete surface in CM 1:4 finished fair & even complete all as specified & directed.

M&L for 25mm thick PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in floors and finishing the concrete even and fair complete all as directed.

M&L for Powder coated aluminium anodised door with frame and shutter and glazing 5mm thick glass and 12mm thick prelaminted particle board exterior grade in bottom panel (kit ply, novapan) glass fixed with rubber gasket with aluminium galzing clips, section of aluminium door shall be of following size :- Frame ; 100 x 44 x 1.98 mm glass thickness with rawal plug. Middle lock rail ; 150 x 44 x 1.98mm thick, Bottom rail ; 150 x 44 x 1.98mm thick, Top rail/Style : 85 x 44 x 1.98mm thick, Glazing beading : 0.70 mm thick , Aluminium handle `D' type 150mm, Aluminium tower bolt 9.9mm dia shoot 200mm long, Mortice lock - 100 mm 4 lever, aluminium stooper cleat - 02 Nos complete all as specified and directed.

M&L for Powder coated aluminium Anodized frame for doors , windows, ventilators, partition wall with one or more rebates including joining cleat for fixing etc complete all as specified. (Minimum thickness of powder coating not less than 50 micron) complete all as directed

M&L for 5.5mm thick glass fixed in aluminium door/window/partition fixed with rubber gasket and aluminium beading complete all as directed.

M&L for 12 mm thick colored pre laminated particle board interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination as in partitions, cup board shutter / shelves, pelmet box and similar items complete all as directed.

Cutting opening, through brick walls built in cement mortar for doors, window and other opening or enlarging existing opening converting window into door opening, etc or cutting out defective brick work for under pinning, including providing, fixing and removing shoring, cleaning and stacking bricks removing surplus serviceable bricks, hard-core etc to store and rubbish not exceeding 50 metre complete all as directed.

M&L for Forming jambs etc. to openings cement mortar 1:4 (to foregoing items) including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete all as directed.

M&L for Making good under cills or over arches in cement mortar 1:4, lintels and bressummers including all pinning when necessary complete all as directed.

Supply and fixing PVC coated galvanised chain link fencing, of size 4mm dia and mesh size 75 x75 mm to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specified and directed.

Mild steel round bars 10 mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F for Mild Steel screw bolts 5 to 10 mm dia (machine made ) with hexagonal or squre head at one end and screwed the other or screwed both ends to be fitted with washers and one hexagonal or squre nuts exc 5 cm but n exc 10 cm long complete all as specified and directed.

Taking down carefully existing aluminum/copper surface/concealed point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces in CM 1:3 of walls, floors, ceiling etc including distempering to match with existing surfaces complete all as specified and directed. Note:- Roof/ceiling height of Tab blgg up to 15 mtr. where U/S point wiring/fitting fixture to be taking out.

M&L for Point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLS having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional area drawn in and including surface PVC casing & caping with all fitting and fixing accessories and 1.5 Sqmm PVC insulated unsheathed multistranded copper conductor cable FRLS as continuous earth conductor, connected to earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxes 1.6mm thick, 60mm deep of required size factory made for mounting switch, regulators etc with and including 3mm thick plastic hylam laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside for mounting switches, sockets etc complete for the following:- Note:- (i) The quoted rates shall be deemed to be inclusive for fixing the casings to surface with using PVC rawl plugs etc. (ii) Point wiring & earth wire shall be connected to each & every sunken box. (iii) All screws, fasteners, bolts, nuts & washer shall be cadmium plated & the cost of which is deemed to be included in the quoted unit rates.

One light point controlled by one, one way 6 Amp switch.

One fan/exhaust fan point controlled by one, one way 6 Amp switch.

One 5 pin 5/6 Amps socket outlet point on the same board with other switch .

One 5 pin 5/6 Amps socket outlet point on independent board controlled by one, one way switch.

One bell point controlled by one, one way 6 Amp button switch.

Description all as per item No 88 here in before but point wiring with 2.5 sqmm multistrand copper conductor cable for five pin socket outlet 15 Amps controlled by one switch on independent board and 2.5 sqmm PVC insulated multi strand copper conductor cable as continous earth wire.

S&F for Switch piano, flush type, single pole one way, 5 Amp complete all specified and as directed

S&F Switch piano, flush type, single pole one way, 15 Amp complete all specified and as directed

S&F Socket outlet, multipurpose, 2 in 1, 5 pin, 5 Amp complete all specified and as directed

S&F Socket outlet, multipurpose, 2 in 1, 5 pin, 15 Amp complete all specified and as directed

S&F Bell push flush type, 5 Amps complete all specified and as directed

S&F Electronic step rotary type fan regulator 100W, 230 volts AC 50Hz complete all as specified and directed

S&F Ceiling rose, 63.5 mm dia, ISI marked, three terminal of polycarbonate /isolated body complete all specified and as directed.

S&F Surface and wall mounted LED batten fitting 25 watt 230 volts AC, cool white not less than 1135 mm extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver complete and connected the same with using PVC sheathed and insulated 3 core flexible 23/0.0076 copper conductor cable including all accessories and fixing arrangement for fixing the light fitting to walls including taking down existing fitting complete all as directed. Make: Philips cat part No. BN 021 LED 25S 6500 PSU GR S2 or equivalent in Havells/Wipro.

S&F 25 watt LED cool white, energy saving IP65, environment friendly, long life, LED street light made up of pressure die-cast aluminium housing with high power LEDs as lighting source and lens embedded PC cover having top opening seperate driver compartment, integrated electronic driver suitable for pole dia 43 mm (max) including suitable size of bracket bent in shape including 2 Nos clamps, nut, bolts etc and fixing on walls complete including taking down existing light fitting etc complete all as directed. Make: Havells cat part No. ENDURAPEARLSL25WLED757SASYTOPC or equivalent in Philips/Wipro.

S&F Aesthetically designed, 2' x 2' cool white flat panel for suitable for armstrong/grid ceiling which provide soft-light and glare free symmetrical illumination of fixture size 595x595x70 mm with and including 42 W LED complete, integrated electronic driver complete and connected the same with using PVC sheathed and insulated 3 core flexible 23/0.0076 copper conductor cable including all accessories and fixing arrangement for fixing the light fitting to ceiling including taking down existing fitting complete all as specified and directed. Make:- Havells Cat Part No-PLUTONEO2X2PLR42WLED857S or equivalent to Philips/Wipro

M&L for Sub main wiring with two single core PVC insulated unsheathed FRLS cable 1100 Volt grade, 4 Sqmm size with multi stranded copper conductor drawing into and including 20mm dia rigid PVC conduit in surface/concealed as required including one run single core PVC insulated unsheathed 4 Sqmm FRLS cable with multi stranded copper conductor as a earth continuity and connected upto DB including taking down old unserviceable submain wiring etc complete all specified and as directed. NOTE: (i) Two run of single core PVC cable with one run of earth conductor & condiut shall be measured as one unit. (ii) The quoted rates shall be deemed to be inclusive for fixing the conduits to surface/concealed with using PVC rawl plugs etc.

S&F MCB DB, sheet metal enclosures double door SPN 12 way with 200 Amps rated bus bar 240 volts 2 in 1 shutter (Metal Door) type with blanking plates where required and IP 43 degree protection fixed in repair complete all as directed.

S&F MCB SP 6 to 32Amps, 240 volts 'C' Curve 10 KA, including connection with suitable size copper lugs complete all as specified and directed

S&F MCB SPN 40 to 63 Amps, 240 volts 'C' Curve 10 KA, including connection with suitable size copper lugs complete fixed in repair all as directed.

Supply and fix in replacement of ceiling fan 1200 mm sweep, 230 volts 50 Hz, energy saving model single phase,26 watt BLDC motor without remote control, pearl white in colour complete with blade, down rod , canopy and connected with ceiling rose etc complete all as specified and directed.

Supply and laying or fixing or passing through pipe XLPE insulated, armoured, heavy duty electric cables 1100 volts grade with stranded aluminum conductor of size 25 sqmm 3.50 core laid in trench/wall/floor/trusses with including taking down existing cable saddle complete all as specified and directed.

M&L for Un-reinforced precast concrete cable cover class LV type1 flat size250 mmx 150 mm x40 mm as protection to under ground cable laid dry flat adjjoining each other complete all as specified and directed

Supply and filling sand with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection complete all as specified and directed. NOTE: - Punned thickness shall be measurement & paid.

M&L for GI pipe light grade ISI marked 40mm bore for cable protection fixed to poles/along wall/floor/under road/across the drain or nallah with calmps, bolts, nuts & washers etc complete all as specified and directed.

M&L for Earthing complete with galvanized iron earth plate electrode 600mm x 600mm x 6mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test point & to main switch board and testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded BT stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI light grade earth lead protection pipe etc complete all as specified and directed. NOTE: (i) Earth lead wire and its protection pipe upto and including 7.5 mtr only from the top of earth electrode are included under this item. (ii) Any joints in earth lead from earth electrode to test point shall not be allowed/permitted. (iii) If the desired earth resistance is not found within permissible limit shall be re done by contractor at no extra cost.

M/S RAJESH KUMAR GOYAL