Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹8.2 CrAdmitted-Finance K 32B SIPCOT INDUSTRIAL COMPLEX GUMMIDIPOONDI CHENNAI TIRUVALLUR TAMIL NADU 601201 | THIRUVALLUR | TAMIL NADU | 601201 | ₹8.2 Cr | L1 | Admitted-Finance |
| 2 | L2₹11.2 Cr+₹3.0 Cr (37.3%)Admitted-Finance 1ST FLOOR SPARTAN HOUSE PLOT NO B29 ROAD NO 18S WAGLE ESTATE THANE W THANE MAHARASHTRA 400604 INDIA | THANE | MAHARASHTRA | 400604 | ₹11.2 Cr+₹3.0 Cr (37.3%) | L2 | Admitted-Finance |
| Sl No | Description | Qty | Unit | IEC Fabchem Limited L1 | BATLIBOI ENVIRONMENTAL ENGINEERING LIMITED L2 |
|---|---|---|---|---|---|
| 1.00CIVIL WORKS AT SITE | |||||
| 1.00 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. | 195 | Square meters | 73 ₹14,235 Lowest | 10,000 ₹19,50,000 |
| 1.00 | Earth work excavation for foundations in all types of soils other than soft and hard rock upto a depth not exceeding 1.5M. from original average ground level, back filling in plinth and around foundations with excavated soil in layers not exceeding 150 MM, watering, consolidating including shoring/ strutting, de-watering by appropriate method and disposing off surplus earth within a distance of 1KM. etc., all complete as per drawings, specifications and as directed by the Engineer. | 339 | Cubic meters | 513 ₹1,73,907 Lowest | 10,000 ₹33,90,000 |
| 1.00 | Same as above but below 1.5 to 3.0 m depth | 86 | Cubic meters | 660 ₹56,760 Lowest | 10,000 ₹8,60,000 |
| 1.00 | Providing and laying plain cement concrete 1:4:8 (one part of cement: four parts of fine aggregate: eight parts of coarse aggregate) using 40 mm nominal size stone aggregate of approved quality for foundations, column footings, steps, under floors including form work, consolidation, levelling, finishing and curing etc., all complete as per drawings, specifications and as directed by the Engineer. | 33 | Cubic meters | 11,733 ₹3,87,189 Lowest | 30,000 ₹9,90,000 |
| 1.00 | Providing, laying and spreading hard stone 90 to 45 mm size in soling in uniform thickness with proper camber, interstices filled with red gravel of plastic index 4 -7, rolling with 8 - 10 Tons capacity vibrating roller, watering, compacting to the required density to form hard base etc., all complete as per drawings, specifications and as directed by the Engineer. | 81 | Cubic meters | 8,800 ₹7,12,800 Lowest | 30,000 ₹24,30,000 |
| 1.00Providing and laying cast - in - situ machine batched and machine mixed design mix M 30 grade Cement Concrete for reinforced cement concrete works using cement content as per approved design mix (350 Kg/Cum minimum) and 20 mm nominal size stone aggregate of approved quality including pumping of concrete to site of laying if necessary, shuttering and centering, consolidating, finishing, providing pockets for bed bolts, curing, scaffolding, admixtures in recommended proportions etc., all complete at all levels as per drawings, specifications and as directed by the Engineer, but excluding cost of reinforcement steel. (Note :- Minimum Cement content in this item shall not be less than 350 kg/cum. No Extra cost shall be payble for extra cement content ) | |||||
| 1.00 | Footings, foundations | 32 | Cubic meters | 14,667 ₹4,69,344 Lowest | 30,000 ₹9,60,000 |
| 1.00 | Beams,Plinth beams | 6 | Cubic meters | 17,600 ₹1,05,600 Lowest | 30,000 ₹1,80,000 |
| 1.00 | Columns, pedestals | 20 | Cubic meters | 17,600 ₹3,52,000 Lowest | 30,000 ₹6,00,000 |
Tender Value
₹6.7 Cr
EMD Value
₹13.4 L
Closing Date
10 Oct 2022, 2:00 pmClosed
Director (Operation/Technical) HWB
HWB, 5th Floor, VSB, Anushaktinagar. Mumbai 400094.
Setting up of HCl and Cl2 gas scrubbing and utilities system at ZC a unit of NFC, Pazhayakayal, Tamil Nadu.
2022_HWB_697696_1
HWB/MRTDDF/2022/01
Open Tender
Construction Works
Item Rate
300 days
ZC a unit of NFC, Pazhayakayal, TN.
Please refer Tender documents.
3 documents required · 3 mandatory
₹0
₹13.4 L
16 Dec 2022
30 Jun 2022
11 Oct 2022
30 Jun 2022
10 Oct 2022
16 Aug 2022
30 Jun 2022 - 4 Aug 2022
Amount
CIVIL WORKS AT SITE
Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.
Earth work excavation for foundations in all types of soils other than soft and hard rock upto a depth not exceeding 1.5M. from original average ground level, back filling in plinth and around foundations with excavated soil in layers not exceeding 150 MM, watering, consolidating including shoring/ strutting, de-watering by appropriate method and disposing off surplus earth within a distance of 1KM. etc., all complete as per drawings, specifications and as directed by the Engineer.
Same as above but below 1.5 to 3.0 m depth
Providing and laying plain cement concrete 1:4:8 (one part of cement: four parts of fine aggregate: eight parts of coarse aggregate) using 40 mm nominal size stone aggregate of approved quality for foundations, column footings, steps, under floors including form work, consolidation, levelling, finishing and curing etc., all complete as per drawings, specifications and as directed by the Engineer.
Providing, laying and spreading hard stone 90 to 45 mm size in soling in uniform thickness with proper camber, interstices filled with red gravel of plastic index 4 -7, rolling with 8 - 10 Tons capacity vibrating roller, watering, compacting to the required density to form hard base etc., all complete as per drawings, specifications and as directed by the Engineer.
Providing and laying cast - in - situ machine batched and machine mixed design mix M 30 grade Cement Concrete for reinforced cement concrete works using cement content as per approved design mix (350 Kg/Cum minimum) and 20 mm nominal size stone aggregate of approved quality including pumping of concrete to site of laying if necessary, shuttering and centering, consolidating, finishing, providing pockets for bed bolts, curing, scaffolding, admixtures in recommended proportions etc., all complete at all levels as per drawings, specifications and as directed by the Engineer, but excluding cost of reinforcement steel. (Note :- Minimum Cement content in this item shall not be less than 350 kg/cum. No Extra cost shall be payble for extra cement content )
Footings, foundations
Beams,Plinth beams
Columns, pedestals
Dyke wall
Grade slab
Providing, laying and fixing in position Fe 500 grade TMT reinforcement steel of M/s. SAIL/TATA/VIZAG brand conforming to IS 1786 for all reinforced cement concrete works including cutting, bending, supplying and binding with 16 gauge MS annealed wire, supplying and laying spacer blocks etc., all complete at all levels as per drawings, specifications and as directed by the Engineer
Providing, fabricating, transporting, erecting and fixing steel structure in position made of angles, channels, flats, pipes, plates, joists/beams, cleats etc., of M/s.SAIL/VSP/TATA brand for platforms, ladders, trusses, bracings, purlins, columns, beams, monorails, stairs, gratings with clips, EPs including making flange connections, splice connections, base plate connections etc., as directed, nuts, bolts, washers, cutting and welding at site, painting the structure with two or more coats of chlorinated rubber paint of approved manufacture and shade over a coat of zinc chromate red oxide primer having total dry film thickness (DFT) of 120 microns etc., all complete at all levels as per drawings, specifications and as directed by the Engineer.
Same as above but for MS bolts, etc complete
Same as item no 8 but for M.S.grating , etc complete
Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement ( weight of stainless steel members only shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc., for payment purpose )all complete at all levels as per drawings, specifications and as directed by the Engineer.
Providing and grouting bed bolt pockets in RCC pedestals/rafts with M-60 grade (Stirrer mixed)cementitious grout (NonShrink) of approved make by suitable means ( Free flowing /pump), curing etc., Complete as per directions of Engineer.
Providing and laying brick masonry in foundation/plinth with cement mortar 1:6 (one cement: six coarse sand) using common burnt clay bricks of class designation 7.5 including racking of joints,scaffolding,curing etc..,all complete at all levels as per drawings, specifications and as directed by the Engineer.
Providing and laying 15 mm thick plaster in cement mortar 1:6 (one cement:six coarse sand) on brick masonry surface including scaffolding, curing etc.., all complete at all levels as per drawings, specifications and as directed by the Engineer.
Providing and applying two or more coats of first quality exterior acrylic emulsion of approved manufacture, colour and shade on newly plastered surfaces of walls over a coat of Exterior primer of approved manufacture to give an even shade including preparing the surface smooth, scaffolding, cleaning etc., all complete at all levels as per drawings, specifications and as directed by the Engineer.
Providing & applying two or more coats of solvent free epoxy paint of HUNTSMAN/CICO or equivalent consisting of base and hardener in suaitable proportions as recommended by manufacturer's on concrete surface to achive a dry film thickness of 250 micron (+/- 5%), over a coat of epoxy primer, to protect concrete surface from various acids, alkalies, sodium sulphate solid as well as liquid solution including preparing the surface by scrubbing with wire brushes, cost of materials, labour, power tools & tackles etc. complete as per manufacturers recommendations, as per specification & as directed by the Engineer-In-Charge.
Dismantling and disposing of existing PPRCC sheet
Demolishing brick work in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.
Demolishing existing PCC manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.
Dismantling existing doors, windows and clerestory windows (Aluminium, steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead as per direction of Engineer-in-charge.
MATERIAL SUPPLY
Supply of equipment as per tender specifications
HCl vapor packed scrubber with tower internals and packings (5S1) (as per Mechanical Tech. Specs M.II.a)
Cl2 gas packed scrubber with tower internals and packings (C11) (as per Mechanical Tech. Specs M.II.a)
Caustic tank (5V02) (as per Mechanical Tech. Specs M.II.b)
Cl2 gas dust separator (F11A) (as per Mechanical Tech. Specs M.II.c)
Re-circulation solution pump (pump with motor) (5P101/102) (as per Mechanical Tech. Specs M.II.d)
Caustic charging pump (pump with motor) (5P103/104) (as per Mechanical Tech. Specs M.II.d)
Hypo re-circulation pump (pump with motor) (P11A/B) (as per Mechanical Tech. Specs M.II.d)
Effluent transfer pump (pump with motor) (7P105) (as per Mechanical Tech. Specs M.II.d)
Cooling water pumps (pump with motor) (7P101/102) (as per Mechanical Tech. Specs M.II.d)
HCl vapor scrubber exhaust blower (blower with damper, motor) (5BL101/102) (as per Mechanical Tech. Specs M.II.e)
Cl2 scrubber exhaust blower (blower with damper, motor) (B11A/B) (as per Mechanical Tech. Specs M.II.e)
Recirculation solution cooler (5EX1) (as per Mechanical Tech. Specs M.II.f)
Caustic dilution cooler (5EX2) (as per Mechanical Tech. Specs M.II.f)
Hypo Cooler (HE11) (as per Mechanical Tech. Specs M.II.f)
FRP Cooling tower with sump (7CT101/102) (as per Mechanical Tech. Specs M.II.g)
Nitrogen gas manifold assembly (as per Mechanical Tech. Specs M.II.h)
Argon gas manifold assembly (as per Mechanical Tech. Specs M.II.h)
Supply of piping material including valves (as per Mechanical technical specifications M.III.a)
SS 316L SEAMLESS PIPE AS PER ASME B 36.19M MOC :- SA 312 TP 316L
Size :- 1” , SCH. 40S,
Size :- 2” , SCH. 40S,
Size :- 3” , SCH. 40S,
SS 316L SORF Flange, Class #150, MOC :- SA 182 F 316L
SS 316L RF Blind Flange, Class #150, MOC :- SA 182 F 316L
SS 316L Elbow Long radius Elbow; MOC :- SS 316L
Size :- 1/2” , SW, 3000#
Size :- 1” ,SW, 3000#
Size :- 2”, BW, SCH. 40S,
Size :- 3”, BW, SCH. 40S,
SS 316L Reducers concentric/Eccentric, MOC :- SS 316L
Size :- 1”x 1/2", SW, 3000#
Size :- 1" x 2”, BW, Sch. 40S
Size :- 1" x 3" ,BW, Sch. 40S
SS 316L Equal Tee , MOC :- SS 316L
Size :- 1”, SW, 3000#
Size :- 2”, BW, Sch. 40S
Size :- 3",BW, Sch. 40S
SS 316L Un-Equal Tee, BW, As per ASME B 16.9 MOC :- SA 403 F 316L
Size :- 2" X 2" X 1 1/2", Sch. 40S,
Size :- 3" X 3" X 1",Sch. 40S
Size :- 3" X 3" X 2",Sch. 40S
Size :- 3" X 3" X 1 1/2",Sch. 40S
SS 316L Special Fittings MOC :- A 182 F 316L
Latrolet, Size :- 1/2",Pipe Run size 2" and One End threaded
Nipolet, Size :- 1/2",Pipe Run size 2" and One End threaded
Pipe Coupler, Size :- 1/2",Full threaded
SS 316L Ball Valve , Class #800, MOC :- SA 182 F 316L and SW end (ASME B16.11)
SS 316L Ball Valve, Class #150 , MOC :- SA 351 Gr CF 8M, RFF-end
CS SEAMLESS PIPE AS PER ASME B 36.10M ,SCH.40 ,MOC :- SA 106 GRADE B
CS SORF Flange ,Class #150 ,MOC :- SA 105
CS RF Blinde Flange ,Class #150 ,MOC :- SA 105
CS Long radius Elbow, MOC :- (SA 105 upto 1.5" and SA 234 WPB for 2" and above)
Size :- 1/2", SW, 3000#
Size :- 1", SW, 3000#
Size :- 1.5", SW, 3000#
Size :- 2", BW, Sch 40
Size :- 3", BW, Sch 40
Size :- 4", BW, Sch 40
Size :- 6", BW, Sch 40
Size :- 8", BW, Sch 40
Size :- 10", BW, Sch 40
CS Reducers Reducers concentric/Eccentric MOC :- (SA 105 upto 1.5" and SA 234 WPB for 2" and above)
Size :- 1”x 1/2", SW, 3000#
Size :- 1" x1.25”, SW, 3000#
Size :- 1/2" x 1.5”, SW, 3000#
Size :- 2" x 1", BW, Sch 40
Size :- 2" x 1.5", BW, Sch 40
CS Reducers concentric/Eccentric As per ASME B 16.9, Sch. 40 ,MOC :- SA 234 WPB
Size :- 2" x 3"
Size :- 3" x 4”
Size :- 4”x2"
Size :- 4" x 6"
Size :- 8"x 6"
Size :- 8"x 4"
Size :- 10" x 6
CS Equal Tee SW, 3000#, MOC :- SA 105
CS Equal Tee As per ASME B 16.9, Sch. 40 ,MOC :- SA 234 WPB
CS Un-Equal Tee MOC :- (SA 105 upto 1.5" and SA 234 WPB for 2" and above)
Size :- 1 "X 1 "X 1 ⁄2", SW, 3000#
Size :- 1 1 ⁄2"X 1 1 ⁄2"X 1 ⁄2", SW, 3000#
Size :- 2" X 2" X 1/2", BW, Sch 40
Size :- 2" X 2" X 1", BW, Sch 40
Size :- 2" X 2" X 1 1/2", BW, Sch 40
CS Un-Equal Tee As per ASME B 16.9 ,Sch. 40 ,MOC :- SA 234 WPB
Size :- 3" X 3" X 1 1/2"
Size :- 3" X 3" X 2"
Size :- 3" X 3" X 1 1/2"
Size :- 4" X 4" X 1 1/2"
Size :- 4" X 4" X 2"
Size :- 4" X 4" X 3"
Size :- 6" X 6" X 3"
Size :- 6" X 6" X 4"
Size :- 8" X 8" X 6"
Size :- 8" X 8" X 4"
Size :- 10" X 10" X 6"
CS Special Fittings ,MOC :- A 105
Latrolet ,Size :- 1/2" ,# 800 Pipe Run size 2" or 3" and One End threaded
Nipolet ,Size :- 1/2" ,# 800 Pipe Run size 2" or 3" and One End threaded
Full Pipe Coupler ,Size :- 1/2" ,# 800
6 inch long Nipple ,Size :- 1/2" ,Sch 40; One end threaded
CS Ball Valve, Class #800 ,MOC :- SA 105, SW end
CS Ball Valve Class #150 ,MOC :- SA 216 WCB, RFF-end
Globe Valve , Class #800 ,MOC :- SA 105, SW end
Globe Valve, Class #150 ,MOC :- SA 216 WCB, RFF-end
Butterfly Valve , Class #150 ,MOC :- SA 216 WCB, RFF-end
Swing Check Valve ,Class #150 ,MOC :- SA 216 WCB, RFF-end
Y type Strainer, Class #150 ,MOC :- SA 216 WCB, RFF-end
Hastelloy Pipe(Seamless) , Sch 40S MOC:- ASME SB 622 LOW C (UNS N10276)
Hastelloy SORF FLANGE (ANSI B 16.5) , Class 150# ,MOC:- ASME SB 462(UNS N10276)
Hastelloy Blind Flange (ANSI B 16.5) , Class 150# MOC:- ASME SB 462(UNS N10276)
Hastelloy Long Radius Elbow (Seamless), End – BW, As Per ASME B 16.9 ,Sch 40s Moc:- ASME SA 462 (UNS N10276)
Hastelloy Reducers Concentric / Eccentric As Per ASME B 16.9 ,Sch 40S, MOC:- ASME SA 462 (UNS N10276)
Size :- 6” X 3”
Hastelloy Equal Tee as per ASME B 16.9 ,Sch 40S MOC:- ASME SA 462 (UNS N10276)
Hastelloy Special Fittings MOC:- ASME SA 462 (UNS N10276)
Latrolet ,Size :- 1”, # 3000 SW, Pipe Run Size 2"/3"/6”
6" Long Nipple ,Size :- ½” , Sch 40S MOC:- One End Threaded
Latrolet ,Size :- 2" , Sch 40S, Pipe Run Size 3"/6”
Hastelloy Ball Valve, Class #150 ,MOC:- ASTM SA 494 ( UNS –N30002) , RFF
CS PTFE LINED PIPING (AS PER MECHANICAL TECH SPECS M.III B.)
CS-PTFE Lined Pipe MoC :- A 106 Gr B pipe SCh - 40 with one flange loose & other fixed with 3 mm thk PTFE Lined
size: 1"NB x 200mm Long ,
size : 1"NB x 300mm Long
size : 1"NB x 500mm Long
size : 1"NB x 1000mm Long
size : 1"NB x 2000mm Long
size : 1.5"NB x 200mm Long ,
size : 1.5"NB x 300mm Long
size : 1.5"NB x 500mm Long
size : 1.5"NB x 1000mm Long
size : 1.5"NB x 2000mm Long
size : 2"NB x 200mm Long
size : 2"NB x 300mm Long
size : 2"NB x 500mm Long
size : 2"NB x 1000mm Long
size : 2"NB x 2000mm Long
CS PTFE Lined Blind Flange ,Moc :-A 105, Class #150; FF Flange with 3 mm thk PTFE Lined
CS PTFE lined 90deg Elbow , both flanges fixed, ,MoC :-A 105 and 3 mm thk PTFE Lined
CS PTFE Flanged Concentric Reducer, SCH - 40 with fixed flanged ends and 3 mm thk PTFE Lined
size : 1"NB x 0.5"NB
size : 1"NB x 1.5"NB
size : 1"NB x 2"NB
size : 1.5"NB x 2"NB
size : 1.5"NB x 3"NB
size : 3"NB x 1"NB
size : 2"NB x 3"NB
size : 4"NB x 3"NB
CS PTFE lined Equal Tee, all flanges fixed and 3 mm thk PTFE Lined
CS PTFE lined Ball valves ,MOC :-SA 216 WCB with PTFE Lined, Two Piece design, Flat Flanged ends; Flange Rating #150, B 16.5
CS PTFE lined Ball type check valve, Moc :-SA 216 WCB with PTFE Lined, Two Piece design, Flat Flanged ends; Flange Rating #150, B 16.5
CS PTFE lined "Y" Type Stariner, Moc :-SA 216 WCB PTFE Lined , with 100% PTFE Filter element and with CS PTFE Lined Blind flange; Flange Rating #150, B 16.5
size : 2"NB ,
PVC LINED FRP PIPING AS PER MECHANICAL TECH SPECS M. III c
PVC Lined FRP Pipe 3mm PVC lining + 8mm thick FRP MOC:- PVC-FRP
Size :- 80 NB
Size :- 150 NB
PVC Lined Flange (BS 4994) ,Class #150, MOC:- PVC-FRP
Size :- 80 NB
Size :- 150 NB
Flanged Nozzle (BS 4994) , Class #150 MOC:- PVC-FRP
Size :- 25 NB
Size :- 40 NB
Size :- 50 NB
Size :- 80 NB
PVC Lined Elbow (BS 4994) ,3mm PVC lining + 8mm thick FRP MOC:- PVC-FRP
Size :- 80 NB
Size :- 150 NB
Equal TEE (BS 4994), 3mm PVC lining + 8mm thick FRP MOC:- PVC-FRP
Size :- 80 NB
Size :- 150 NB
PVC NRV (Check Valve) PN 10; flanged end, PCD as per #150 of ASME B16.5
Size :- 150 NB
PVC Butterfly Valves PN 10; flanged end, PCD as per #150 of ASME B16.5
Size :- 150 NB
MISCELLANEOUS ITEMS AS PER MECHANICAL TECH. SPECS. M.III d.
PTFE Flat Ring Gasket, #150 Class, 3 mm Thick
Size :- 15 NB
Size :- 25 NB
Size :- 40 NB
Size :- 50 NB
Size :- 80 NB
Size :- 100 NB
Size :- 150 NB
Size :- 200 NB
Size :- 250 NB
Graphite Flat Ring Gasket, #150 Class, 3 mm Thick
Size :- 15 NB
Size :- 25 NB
Size :- 40 NB
Size :- 50 NB
Size :- 80 NB
Size :- 100 NB
Size :- 150 NB
SS Full Threaded Stud with two washers and two nuts
Size :- M 12 X 100 Long
Size :- M 1 6X 150 Long
CS Full Threaded Stud with two washers and two nuts
Size :- M 12 X 100 Long
Size :- M 16 X 150 Long
Size :- M 12 X 150 Long
CS Grouting Bolt with one 3mm thk washer and nut
Size :- M16 X 250
Size :- M20 X 300
PTFE sheet 3 mm Thick
Size :- 1mtr X 1mtr X 3 mm thk
Rubber sheet 3 mm Thick natural rubber sheet
Size :- 1mtr X 1mtr X 3 mm thk
Rubber sheet 5 mm Thick natural rubber sheet
Size :- 1mtr X 1mtr X 5 mm thk
U clamp with 2 nut and two washer gasket
Size :- 15 NB
Size :- 25 NB
Size :- 40 NB
Size :- 50 NB
Size :- 80 NB
Size :- 100 NB
Size :- 150 NB
Size :- 200 NB
Size :- 250 NB
FLEXIBLE HOSE
FLEXIBLE HOSE for ARGON SUPPLY TO VACUUM LADLE, SS MOC:- SS 304 , Size :- 15 NB X 2 M Long
FLEXIBLE HOSE ,for NITROGEN GAS MANIFOLD CONNECTION WITH NITROGEN GAS HEADERSS MOC:- SS 304 , Size :- 15 NB X 2 M long.
FLEXIBLE HOSE , for ARGON GAS MANIFOLD CONNECTION WITH ARGON GAS HEADERSS MOC :- SS 304 ,Size :- 15 NB X 2 M Long.
SAFETY CAGE
SAFETY CAGE for SAFETY CAGE AROUND HCL / CL2 HASTELLOY PIPE Size :- Dia 300, MOC :- MS/GI
Fume hood , For HCl fume suction MOC :- PVC , As per tender drawing.
Flexible hose , for HCl fume suction MOC ;- PVC , Size :- 6 inch X 1 Mt long.
Structural Steel MOC :-IS 2062, As per Technical specifications of Civil
Angle Size :- ISA 35x5 ,
Angle Size :- ISA 50x5
Angle Size :- ISA 75x6
C- Channel Size :- ISMC 100 x 5
C- Channel Size :- ISMC 150 x 6
Structural Steel Plate ,MOC :- IS 2062
MS Plate Size :- 5mx 2m x 10 mm thk
Paint
Chorinated rubber paint of different shade
Thinner for above paint of same brand as paint
Red-oxide Zinc primer for above paint of same of brand and manufacturer
Thinner for above Red oxide of same brand as paint
Supply of Instrumentation items as per enclosed technical specifications
Level Switch ( LS-101, LS-102, spare equivalent to LS-101)
Solenoid operated ON/OFF valve (SOV-101, SOV-102,spare equivalent to SOV-102)
Solenoid operated ON/OFF valve ( SOV-103, SOV-104)
Compound Pressure gauge (CPG104A, CPG104B)
Compound Pressure gauge/Pressure gauge (CPG106, CPG107, CPG108A, CPG108B, CPG-110, CPG-111, PG-112A, PG-112B, spare equivalent to CPG-110, CPG-108A)
Pressure gauge (PG101A, PG101B, PG102, PG103, PG-701A, PG-701B, PG-702, CPG105A, spare equivalent to PG-701A)
Pressure gauge (PG109A, PG109B, PG113A, PG113B, PG-115A, PG-115B, PG-116, spare equivalent to PG-109A)
Temperature Gauge (TG-101, TG-102, spare equivalent toTG-101)
Temperature Gauge ( TG-104)
Temperature Gauge with switch (TG-103, spare equivalent toTG-103)
RTD (TIT-101, TIT-102, TIT-103, TIT-104, TIT-105, TIT-106, spare equivalent to TIT-101)
RTD (TIT-701, TIT-702, spare equivalent to TIT-701)
Level gauge (LG-101, LG-102, LG-103)
Adjustable Pressure Gauge (APR-101A, APR-101B, APR-102, APR-103, APR-104, spare equivalent to APR-101A)
Pressure Transmitter (PIT-101, PIT-102, PIT-103, PIT-105, Spare equivalent to Tag no. PIT 103)
Pressure Transmitter (PIT-104,Spare equivalent to Tag no. PIT 104)
Differential Pressure Transmitter (DPIT-101, DPIT-102, DPIT-103)
Rotameter (RT-101A, RT-101B, RT-104, spare equivalent to RT-101A)
Rotameter (RT-102, RT-103, spare equivalent to RT-102)
Flow Transmitter (FIT-101)
Flow Transmitter (FIT-102, FIT-104, spare equivalent to FIT 102)
Chlorine Detector ( LD-1, LD-2, Spare equivalent to LD-1)
HCl Detector ( HCLM-1, HCLM-2, HCLM-3, Spare equivalent to HCLM-1 )
Chlorine and HCl Indicator cum alarm unit in control room
Cable tray (50mm wide, 50 mm (H) and 3 mm (th))
Cable tray (100mm wide, 50 mm (H) and 3 mm (th))
Junction Box
Single pair I&C cable
Triad I&C cable
Miscellaneous erection materials (tubes, tube fittings, 2/3/5 manifolds flanges, Siphon coil for cooling,FRP splice for cable trays, lugs, cable glands, ferrule, Teflon tape etc.)
Supply of Electrical items as per tender specifications
Supply of Push Button station
Supply of 3 Core 2.5 sqmm FRLS armoured copper cable
Supply of 3 Core 4 sqmm FRLS armoured copper cable
supply of 3 Core 16 sqmm FRLS armoured Al cable
supply of 3 Core 35 sqmm FRLS armoured Al cable
1.5sqmm 5Core Cu cable for LPBSas
Double compression gland for 3x35 sq mm Armoured cable
Double compression gland for 3x16 sq mm Armoured cable
Double compression gland for 3x4 sq mm Armoured cable
Double compression gland for 3x2.5 sq mm cable
Double compression gland for 1.5qmm, 5Core, Cu Armoured cable
Double compression gland for 1.5qmm, 12pair, Cu Armoured cable
copper lug suitable for 35 sq mm cable termination
copper lug suitable for 16 sq mm cable termination
copper lug suitable for 4 sq mm cable termination
copper lug suitable for 2.5 sq mm cable termination
copper lug suitable for 1.5 sq mm C& I cable termination
Type - 1 light fixtures
Type - 2 light fixtures
100mm FRP cable tray
Earthing strip & Accessories for earthing
Supply of spares items for equipment as per equipment data sheets
16MM Pall rings for Chlorine scrubber
38MM PP Pall rings for HCl scrubber
Spares for Re-circulation solution pump (5P101/102)
Spares for Caustic charging pump (5P103/104)
Spares for Hypo re-circulation pump (P11A/B)
Spares for Effluent transfer pump (7P105)
Spares for Cooling water pumps (7P101/102)
Spares for HCl vapor scrubber exhaust blower (5BL101/102)
Spares for Cl2 scrubber exhaust blower (BL11A/B))
Spares gaskets for Recirculation solution cooler (5EX1)
Spares gaskets for Caustic dilution cooler (5EX2)
Spares gaskets for Hypo Cooler (HE11)
Spares for Cooling tower (7CT101/102)
ERECTION WORK AT SITE
Erection & testing of instrumentation items as per tender specifications
Installation & Commissioning of Field Instrument: Installation of field instruments, this includes, supply and fabrication of supporting structural material, welding/fixing of mounting bracket / channel with consumables like nuts bolts, fittings, teflon tape etc., cable glanding and termination of cable with double cross ferrule and suitable lugs etc. Commissioning of Field Instruments
Laying and erection of cable trays and JBs pertaining to establishment cable connection between Field Instrument to local JB. this includes supply of mounting / supporting structural material, tray connector and consumables.
Cable tray (50mm wide, 50 mm (H) and 3 mm (th))
Cable tray (100mm wide, 50 mm (H) and 3 mm (th))
Installation of JB including supply of cable glands, double cross ferrules, lugs, plugs for unused holes etc.
Cable Laying : (triad + single pair) Pulling the cables to the cable trays / cable riser/sleeve, routing of cable on cable tray as directed by Engineer Incharge / site Incharge, dressing and clamping of the cables, cable glanding and termination at Field Instrument end and local JB through suitable lugs, double cross ferrule etc. Consumable required for cable laying as per good engineering practice is in the scope of this tender.
Erection & testing of electrical items as per tender specifications
Installation & Commissioning of LPBS: Installation of LPBS, this includes, supply and fabrication of supporting structural material, welding/fixing of mounting bracket / channel and LPBS with consumables like nuts bolts etc., cable glanding and termination of suitable cable at feeder and push button end using suitable lugs as per tender specification. (LPBS, Lugs and glands are supplied by contractor or issued as free issue material by department)
Laying and erection of cable trays (supplied by contractor or issued as free issue material by department) including mounting / supporting structural material, tray connector and consumables.
Less than or equal to 100mm width cable tray
Greater than 100mm upto 300mm width cable tray
Installation & Commissioning of Lighting Fixtures: Installation of Lighting Fixtures, this includes supply and fabrication of supporting structural material, gland & lugs, welding/fixing of mounting bracket / channel and Lighting Fixtures with consumables like spacers & Clamps for cable dressing, nuts, bolts etc., cable laying and its dressing, cable glanding and termination of suitable cable at LDB/ELDB and lighting fixture as per tender specification.
Type - 1 light fixtures
Type - 2 light fixtures
Cable Laying (other than Lighting Fixtures): Pulling the cables to the cable trays / cable riser/sleeve, routing of cable on cable tray as directed by Engineer Incharge, dressing and clamping of the cables, cable glanding and termination of suitable cable at feeder / motor terminals / field JB Terminals using suitable lugs as per tender specifications. (Cables, glands and lugs are supplied by contractor or issued as free issue material by department)
Cable Laying: 3 Core 4 sqmm FRLS armoured Cu cable
Cable Laying: 3 Core 16 sqmm FRLS armoured Al cable
Cable Laying: 3 Core 35 sqmm FRLS armoured Al cable
Cable Laying: 1.5sqmm 5Core Cu cable for LPBS
Cable Laying: 1.5sqmm 12 pair Cu cable from field JB to DCS
Erection and Commissioning of Earth strips from existing earth grid to Motors, Metallic Tanks and other Process equipment etc installed under the scope of this tender
FABRICATION / ERECTION WORK AT SITE
Piping fabrication work as per Mechanical Tech. Specs M.IV.
SS 316L welding by GTAW
CS welding Root by GTAW and filling by SMAW
Hastelloy 272 C welding by GTAW
Structural welding
Erection of mechanical equipment as per Mechanical Tech. Specs M.V
HCl scrubber column (5S1)
Cl2 scrubber column (C11)
UHMWPE Centrifugal pumps with motors (5P101/102/103/104/105, P11A/B)
Cooling water pumps with motor (7CT101/102)
Centrifugal blower with motor (5BL101/102, B11A/B)
Plate Heat Exchangers (5EX1, 5EX2, HE11)
Cooling tower (7CT101/102)
Caustic solution preparation tank (5V02)
Chlorine gas dust separator (F11A)
Gas manifold (Argon & Nitrogen)
Piping erection work as per as per Mechanical Tech. Specs M.V
Erection of SS 316L including Pickling and Passivation
Erectionof CS pipe including painting
Hystelloy Pipe erection work
Erection of CS+PTFE including painting
PVC- FRP Ducting installation including Welding of PVC, FRP raping up to 8mm on weld joint, erection and clamping
Welding of PVC lining, joining of duct including FRP raping up to 8mm on weld joint, fixing of nozzle, stub ends, branch connection
PVC- FRP Ducting erection and clamping at verious elevation
ASSISTANCE FOR COMMISSIONING OF SYSTEM AT SITE AS PER TENDER SPECIFICATIONS
Skilled manpower
Semi skilled manpower
BATLIBOI ENVIRONMENTAL ENGINEERING LIMITED
stage.html
html • 0.03 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 3.36 MB
BOQ_734103.xls
BOQ • 0.48 MB
TENDERDOCUMENTR1.pdf
Tender Documents • 23.93 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .