SPECIAL REPAIRS TO COMPOUND WALL AND AS and AS TO TOILETS AT SECTOR A AND SPECIAL REPAIRS TO ROAD FURNITURE AT DOLPHIN HILL VISAKHAPATNAM

Amount

Demolition of Brick / Stone Masonry built in Cement Mortar including all quoins arches pillars etc and removing rubbish to a distance not exceeding 1.5 KM complete all as specified and as directed.

M & L for brick work with Fly Ash bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

M & L for walling of random rubble masonry, uncoursed, well bonded, bedded and solidly hearted, built in Cement Mortar 1:6 complete all as specified and directed.

M & L for Raised Pointing in Cement Mortar 1:3 to random rubble uncoursed or brought up to coursed masonry complete all as specified and directed.

M & L for Providing Precast Cement Concrete Solid Block Masonry of 1:3:6, Type C1 using 20mm graded stone aggregate exceeding 100mm width with plain or interlocking joints set in cement mortar 1:6 complete all as specified and as directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling,uncoursed or brought face from straight edge held against the dressed surface not exceeding 40mm complete all as specified and directed.

Dismantling Posts or Struts [Wood, Steel or RCC] of any section, embedded in natural ground including taking out embedded portion and making good disturbed surfaces complete all as specified and as directed.

Demolition of Unreinforced Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

Demolition of Reinforced Cement Concrete of Roof, Floors [other than ground floor], beams, staircase, landing, Chajjas and similar suspended work including reinforcement cut as required to facilitate demolition and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

M & L for PCC 1:2:4, Type B-1, using 20mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings, Coping etc. complete all as specified and as directed.

M & L for RCC M-30,Design Mix, using 20mm graded stone aggregate for chajjas and the like etc complete all as specified and as directed.

Use and removal of steel formwork to Chullah hoods, Chajjas, troughs and similar items including edges and similar works for fair finished surfaces of concrete complete all as specified and as directed.

M & L for RCC M-30, Design Mix, using 20mm graded stone aggregate as in Slabs supported on walls, beams, columns, landings, shelves, Chajjas and the like complete all as specified and as directed.

Use and removal of steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including fair finished surfaces complete all as specified and directed.

M & L for RCC M-30, Design Mix, using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts etc complete all as specified and as directed.

Use and removal of steel formwork to sides of pillars, posts, struts, piers, columns and stanchions of any shape / cross section for rough finished surfaces of concrete complete all as specified and as directed.

M & L for RCC M-30, Design Mix, using 20mm graded stone aggregate as in Beams, columns, cantilevers, bressummers, lintels over 1.5m span etc. complete all as specified and as directed.

Use and removal of steel formwork to sides and soffits of floor or roof beams, beam launchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc, splays between floors and beams and similar works for fair finished surfaces of concrete complete all as specified and as directed.

M & L for Plain / Reinforced cement concrete Type B1 [Nominal Mix] 1:2:4 using 20mm graded stone aggregate in lintels,bands etc up to 1.5m span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work, complete all as specified and as directed.

Taking down Chowkats or frame with shutters exceeding 1.5 Sq.m but not exceeding 4.00 Sq.m each complete all as specified and as directed.

S & F Factory made UPVC Sliding Window with two nos. glass shutters and one no. mesh shutter, Three Track, White Colour of area not exceeding 2.0 Sq.m, made of extruded profiles with wall thickness of 2.3mm±0.2mm, Window profile with hollow section with multi chamber, 112mm X 45mm, Sliding Sash of size 42mm X 67mm, Sliding Mesh Sash of size 42mm X 57mm, Sliding Interlock [One vertical length in each shutter] of size 45.50mm X 28mm, Glazing Bead of size 24.50mm X 16mm shall be mitred cut and fusion welded at all corners, including drilling holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM Gasket, 1.2mm±0.2mm thick Galvanized Steel Frame of size 30mmx 18mm, 2 Nos, Sliding Sash of size 30mm x 18mm, Sliding Mesh Sash of size 26mm x 10mm profile to be inserted in required profile, frame shall be fixed to the wall with 8mm X 100mm long fasteners, Hardware such as Touch lock of zinc alloyed [white powder coated], Steel roller system, including all necessary accessories shall be provided with proper operative and locking hardware mechanism, frame shall be fixed to wall with high quality fasteners and silicon glue shall be applied to fill up gap between frame and wall to make leak proof complete all as specified and as per Manufacturer instructions. Note: (i) The unit rate quoted by the contractor includes cost of fixing of galss and wire cloths including all other connected accessories. (ii) The Glass Panes and wire cloths shall be measured and paid saperately at supply only rates under relavent Items of Schedules. (iii) The size of UPVC sections specified in the description of item is minimum requirement, if the same size of section is not available, next higher size shall be provided by the contractor without any extra cost to the Department.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed. Note: (a)M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately (b)For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: Stainless steel butt hinges and necessary S S screws shall be paid separately

Supply only 5.5mm thick Sheet Glass ordinary quality in squares exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

Supply only Stainless steel wire cloth / mesh with average aperture not exceeding 1.40 mm and dia of wire 0.36 mm complete all as specified and as directed.

S & F in repairs Galvanised, 2 Strand, Steel Barbed Wire 2.24mm dia, Barbed with 2mm dia bars at 75mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc complete all as specified and directed. Note: Each line of wire will be measured for payment.

S & F in repairs Mild Steel work conforming to Fe - 290, Grade E-165 as in Hand Rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for Balusters Running Bars, for Doors, Balusters, Nosing to Steps including embedding in concrete and screwing etc., Wind Ties for roof including securing bolts, Posts and Struts in Fencing including cutting tops to shape as directed, bending to shape, notching for wire, drilling holes or as in flat iron fillets [for securing wire mesh and barbed wire etc.] including all necessary drilling, bolting or riveting, etc. and similar work complete all as specified and directed.

S & F Aluminium anodised barrel Tower Bolt of size 150 mm size of extruded section complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt of size 100 mm size of extruded section complete all as specified and as directed.

S & F Floor Door Stopper of size 150 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

S & F Brass Sliding Door Bolt with sand or die-cast brass hasp, staple [Bolt Type] of size 300 mm and fixing bolt with rolled or drawn brass bolts complete all as specified and as directed.

S & F Door Closer Hydraulically Regulated, Designation No. 3 universal type, suitable for door shutters of 851 mm to 1000 mm in width and of weight between 61 to 80 Kg of aluminium body complete all as specified and as directed.

S & F Brass Polished Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and as directed.

S & F Floor Door Stopper of size 150 mm of Brass body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and as directed.

S & F in repair 100 mm size, medium weight Butt Hinges, Stainless steel including fixtures complete all as specified and as directed.

S & F in repair 100 mm long Brass flush bolt, type 2 and fixed flush complete all as specified and as directed

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

Dismantling of stone slabs and tiles in flooring, apron etc of any description or thickness laid dry and pointed in any mortar complete all as specified and directed.

M & L for PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for Hardcore of gauge not exceeding 63mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface complete all as specified.

M & L for Boulder pitching, laid dry, hand packed tightly and grouted in Cement Mortar 1:6 complete all as specified and directed.

M & L for Vitrified Tiles, Double Charged, Coloured, Premium Quality, of size not exceeding 0.36 Sq.m, 8 to 9 mm thick as in Floors and jint shall be kept as 3mm filled with epoxy. To attain the best result 3mm thick tile spacers tobe used,Masking tape shall be put before putting the epoxy grout and the grout shall be througly cleaned immediately including screed bed or bedding layer of mortar 10 mm thick in Cement Mortar 1:6 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Vitrified Tiles, Double Charged, Coloured, Premium Quality, of size not exceeding 0.36 Sq.m, 8 to 9 mm thick as in Skirting and Dado, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Joint Free Glazed Ceramic Tiles, Edge Cut, Concept Type, Coloured, Premium Quality, of size 450 mm X 300 mm, 7 to 8 mm thick as in Vertical Surfaces such as Skirting, Dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. The colour / shade / design of tiles shall be as approved by GE.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Floors, Treads of Steps, Window Cills, Cooking Platform etc., and the like with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single stone slab shall be used for entire Width and Length of Steps, Window Cills, Cooking Platform etc. and joints shall match with the flooring. The edges of treads shall be bull nosed / half rounded. The edges of the treads and landings shall also be provided with three Nos of grooves.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Skirting, Dado, Risers of Steps, Jambs, Pillars, Wall Lining [Veneering to Wall] etc. with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: Single stone slab shall be used for entire height of Skirting / Dado / Risers and joints shall match with the flooring.

Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces, ceiling surfaces etc including raking out joints, hacking for key scrubbing down with water etc and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 10 mm thick in Cement Mortar 1:4, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for preparing newly plastered wall/ceiling surfaces by using vaccume based sanding machine and applying two coats of Acrylic washable Distemper by using auto roller/airless sprayer, over a coat of alkali resistant primer over 1mm thick Cement based Wall Care Putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces complete all as specified and as directed. Note:- The contractor shall carryout Distempering & allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering & allied works through their authorised applicators before commencement of the work to GE for approval.

M & L for Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] by using auto roller/ airless sprayer over a Coat of Exterior Primer over 1 mm thick of Cement based Wall Care Putty [primer and putty shall be of same manufacturer as that of exterior emulsion paint] by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty on newly plastered walls/ ceiling, pillasters, bands, borders, soffits of chajjas and projections including rubbing with sand paper to obtain a smooth surface complete all as specified and as directed. Note:- The contractor shall carryout Exterior Emulsion Painting and allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Exterior emulsion painting through their authorised applicators before commencement of the work to GE for approval.

M & L for Complete removal of existing treatment of any description on walls/ ceiling, pillasters, bands, borders, soffits of chajjas and projections by using vaccume based sanding machine, removal of nails including rubbing with sand paper to obtain a smooth surfaces and applying One coat of Weather Proof Exterior Emulsion Paint [100% Acrylic] by using auto roller/ airless sprayer over a Coat of Exterior Primer over 1 mm thick of Cement based Wall Care Putty [primer and putty shall be of same manufacturer as that of exterior emulsion paint] by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty complete all as specified and as directed. Note:- The contractor shall carryout Weather proof Exterior Emulsion Painting under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Weather proof Exterior Emulsion Painting through their authorised applicators before commencement of the work to GE for approval.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

Dismantling water tanks of size exceeding 1000 litres and not exceeding 250 litres and removing to store complete all as specified and as directed.

S & F Rotational Moulded Polythene [HDPE] Water Tanks, Double Layered, ISI Marked, Cylindrical & Vertical Type 1000 Litres Capacity hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete all as specified and as directed.

S & F in repairs Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 Mpa, 20 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to IS, ISI Marked complete all specified and as directed.

S & F in repairs Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 Mpa, 25 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to IS, ISI Marked complete all specified and as directed.

S & F in repairs Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 Mpa, 40 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to IS, ISI Marked complete all specified and as directed.

S & F 16 mm outer diameter CPVC Pipes SDR 11 & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing, including taking down of existing unserviceable GI pipes and connections of any description complete all as specified and as directed.

S & F CPVC Pipes 20 mm outer diameter SDR 11 & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing including taking down of existing unserviceable GI pipes and connections of any description complete all as specified and as directed.

S & F CPVC Pipes 25 mm outer diameter & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing including taking down of existing unserviceable GI pipes and connections of any description complete all as specified and as directed.

S & F CPVC Pipes 40 mm outer diameter & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing including taking down of existing unserviceable GI pipes and connections of any description complete all as specified and as directed.

Taking down Eaves Gutters /SWR Pipes [any size or pattern], including all fittings, heads, shoes, bends, swan-necks, etc. from any height complete all as specified and as directed.

S & F 110mm bore UPVC [SWR] pipes single socketed, in any length with rubber ring/ solvent cement joints, laid in trenches or in floors complete all as specified and as directed.

S & F 110mm bore UPVC [SWR] pipes single socketed, in any length with rubber ring/ solvent cement joints, fixed to walls in any position with necessary brackets, clamps, bolts, nuts, etc., complete all as specified and as directed.

S & F 75mm bore UPVC [SWR] pipes single socketed, in any length with rubber ring/ solvent cement joints, fixed to walls in any position with necessary brackets, clamps, bolts, nuts, etc., complete all as specified and as directed.

S & F 75mm bore UPVC [SWR] pipes single socketed, in any length with rubber ring/ solvent cement joints, laid in trenches or in floors complete all as specified and as directed.

S & F 110 mm bore UPVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore UPVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore UPVC [SWR] Branch Piece, double [Single "Y"] equal or unequal including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore UPVC [SWR] Branch Piece, double [Single "Y"] equal or unequal including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore UPVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed.

S & F in repairs 75mm outlet UPVC [SWR] Floor Trap with grating including jointing with solvent cement complete all as specified and as directed. Make:- Cat Part No. FT-25 of Prayag or equivalent approved make

S & F in repairs Bottle Trap of CP brass suitable for bore dia of discharge pipe 32 mm [Minimum weight 260 Grams] having minimum water seal of 25mm complete all as specified and as directed. Make:- Cat Part No. BEA-23 of Prayag or equivalent approved make

S & F in repairs 450 mm long Hose pipe with two 15mm nuts & rubber washer as per Jaquar Catalogue No. ALD-805B or its equivalent in Kohler / Cera / Parryware / Grohe / Crabtree complete all as specified.

S & F in repairs Bib Taps, 15 mm dia, Brass Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as per Jaquar Catalogue No. LYR-38037/SPJ-CHR 35429PM or its equivalent in Kohler / Cera / Parryware / Grohe/Prayag complete all as specified.

S & F in repairs Two way Bib tap, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as per Jaquar Catalogue No. FLR-5041N or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F in repairs Angle Cock, 15 mm dia, brass, Chromium Plated, fancy type, screwed down high pressure for iron pipe etc as per Jaquar Catalogue No. KUP-35053PM or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F in repairs 4way Diverter for concealed fittings with built-in Non-returning valves with diverter handle 15 mm bore, chromium plated as per Jaquar Catalogue No. LYR-38421/DRC-CHR-37193 or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F in repairs Health Faucet with 1 m long flexible tube, wall hook, non return valve complete as per Jaquar Catalogue No. ALD-573 or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F in repairs Single lever basin mixer without popup waste with 450 mm long Braide hose as per Jaquar Catalogue No. LYR-38001B or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F CP click clack waste 32 mm size full thread with 80mm height complete all as specified and as directed. Make: Cat No ALD-727 of Jaquar & Company Pvt. Ltd. or equivalent in Prayag / Kohler / Roca / Cera [First Quality] / Hindware [Italian Collection] / Parryware [Superfine] / Johnson

S & F in repairs Stainless Steel, Soap Dish, Fancy Type complete all as per Jaquar Catalogue No. ACN-1131N or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F in repairs Stainless steel Towel ring complete all as per Jaquar Catalogue No. ACN-1121BN or its equivalent in Kohler / Cera / Parryware / Grohe / Crabtree complete all as specified.

S & F in repairs Brass Chromium Plated Tubular Towel Rail, 20mm dia, D Type, 600 mm long between flanges complete all as specified and as directed. (Make:-Jaquar cat No. ACN-1111SM or equivalent in Kohler / Cera / Parryware / Grohe / Crabtree/ Blue Star

S & F in repairs Stainless Steel Towel rack 600mm long with Lower Hangers, complete all as per Jaquar Catalogue No. ACN-1181S or its equivalent in Kohler / Cera / Parryware / Grohe / Crabtree Shine complete all as specified.

S & F in repairs Tumbler holder complete as per Jaquar Catalogue No. ACN-1141N or its equivalent in Kohler / Cera / Parryware / Grohe / Crabtree complete all as specified.

S & F in repairs Stainless Steel Toilet Paper Holder, Chromium plated, Fancy type complete all as per Jaquar Catalogue No. AKP-35753PS or its equivalent in Kohler / Cera / Parryware / Grohe / Crabtree complete all as specified.

S & F in repairs Stainless steel peg set of 6, fancy type for hanging clothes complete all as specified and as directed.

S & F in repairs Stainless steel Shower panel, anti-linger print body, 3-in-1 system with inbuilt ABS top shower with 50 Nozzles, chromium plated ABS hand shower, multi function water diverter, 1.5 m long stainless steel double locked flexible hose pipe complete all as per Jaquar Catalogue No. JPL-SSF-ST8858B3 or its equivalent in Kohler / Cera / Parryware / Grohe / Crabtree complete all as specified.

S & F Factory made ready to install Non-Toxic, Lead & Cadmium free, single extruded, Water proof, termite proof, fire retardent, excellent screw holding capacity, Solid PVC Boards, 20mm thick, Both Side Laminated in White as in Cupboard Shelves fixed to Guide Rails with stainless steel screws complete all as specified as directed.

S & F in repairs stainless steel sliding/telescopic channel of length 20 inch (500mm) with 3 Nos of holding ball of load carrying capacity 45-50 Kg of 202 grade steel, width 45mm including necessary fixing arrangement complete all as specified and directed.

S & F in repairs Continuous [Piano] Hinges, Mild Steel, Bright finish or Electrogalvanised and width of Flaps 30mm [When Open] complete all as specified and as directed.

S & F in repairs Drawer pulls , 4 screw plate with fixed dished pull, 80 mm to 100mm long brass complete all as specified and as directed.

S & F 12mm thick Toughened Plain Glass as in Door/ window/ partition panels including cutting to shape , drilling hole as srequired and grinding the edges including necessary fittings complete all as specified and as directed.

S & F Solar control film 50 micron thick reflective type all as per manufacturer's instructions complete all as specified and as directed.

S & F Double Action Floor Spring Hydraulically Regulated made of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed.

S & F 300mm long Stainless Steel Handle, of extruded section Fabricated Type complete all as specified and as directed.

S & F Ball Valves, 40 mm Bore, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe etc complete all as specified and as directed.

S & F Cascade type Single piece WC with UF soft close slim seat cover, hinges, fixing accessories, accessories set and cistern fittings of size 360 x 725 x 735 mm with S trap of 300mm complete all as per Jaquar Catalogue No. WHT-6851S300UF or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Modular BWR Plywood Vanity Wash Hand basin Cabinet, colour Wallnut wenge, having BWR plywood cabinet, PVC membrane doors, hafele hinges dimemsions 100 x 45 x 83 cms, having three side drawer, CP handles and legs including vitreous china wash basin and fittings except faucets and mirror complete all as per manufacturer's specification and as directed. Make:- RAK Ceramic Catalogue No. RAK-JOY-JOYOS020MGY or euivalent approved make.

S & F Bath cubical made of 6mm thick tempered glass, corner entry enclosures with door sliding to both sides in standard of size ( H: 2300 mm, w: 1601-2000mm), chrome finish including all fittings and fixtures complete all as per manufacture's specifications and as directed. Make:-Jaquar Catalogue No. JSE-CHR-830ST1620H23 or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine

S & F in repairs Corner Glass Shelf with Bracket complete as per Jaquar Catalogue No. ACN-1173 or its equivalent in Kohler / Cera / Parryware / Grohe / Crabtree complete all as specified.

S & F in repairs Road Stud, Two way reflective of size 100mm X 110mm X 20 mm [Approximately], ABS body with high intensity grade retro reflective panel of Amber, Red or White colour conforming to IRC - 67, fixed with complete all as specified and as directed.

S & F in repairs Solar Road Studs [Bi-Directional] made of Aluminium Die cast matt finish of size 125 X 125 X 25mm [Approximately], working on High Efficiency Mono-Crystalline Solar Panel 2.4 V / 0.3 Watt, One Ni-Mh or NI-cd Rechargeable Battery [1.2V / 1600 MA] with Six Super Bright LEDs with 10,000 to 18,000 mcd [Millicandela], with a minimum Operating time of 3-4 consecutive days with full charge, viewing distance / visibility not less than 800m with 2 Hz Flash Rate, Self operated from Dusk to Dawn, anti twist ribs on the bottom anchor / shank with high intensity reflective grade polymer sticker and conforming to IS - 12063, of Colour yellow or red or blue or green or white as approved by GE complete all as specified and as directed.

M & L for Road Marking Strips, Lines, Dashes, Arrows, Letters etc of 2.5 mm thick [Reflective Type] of colour White or Golden Yellow on roads, pavements and the like exceeding 10cm but not exceeding 15cm wide with Hot Thermo Plast material by fully automatic thermoplastic paint applicator machine, fitted with profile shoe, glass beads dispenser, propane tank heaters and profile shoe heater, driven by skilled operator on road surface complete as per MOSRT & H specifications including cleaning the road surface of all dirt, scales, oil grease and foreign materials etc complete all as specified and as directed.

S & F in repairs Road Side Delineator [Reflector] as per approved model and conforming to IRC - 67, made of Powder Coated MS Pipe, 50mm bore, 600mm height, Heavy Grade, fitted with 2 Nos. of 100mm dia highly reflective reflectors made of PMMA Material with ABS Round Body, anti rust & anti theft steel net, fixed with Bolts, Nuts and Epoxy Glue, which emit excellent reflection during night time, with 3 reflective strips of colour Amber, Red or White, as approved by GE and duly embeded in PCC 1:2:4, Type B1 of suitable size fixing MS Post and earthwork etc. complete all as specified and as directed.

Taking down carefully copper / aluminium point wiring [light, fan, socket or power] complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and making good the disturbed surfaces all as per existing complete all as specified and as directed.

M & L for Point Wiring complete with 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, Two runs, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, conforming to IS - 694 drawn through and including heavy duty PVC Conduit, 20 mm dia including all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type and Metal GI Flush Box of suitable size and thickness including Modular type Base / Grid Frame & Cover Frame for housing Modular Type Switches, Sockets and Regulators etc. concealed in walls, including 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable as earth continuity conductor with colour coding and connecting to Earth Dolly for One Light / Fan Point / Bell Point complete all as specified and as directed.

All as per Serial Item No. 115 above but One 3 Pin Socket Outlet 5 Amps on same Board complete all as specified.

All as per Serial Item No. 115 above but one 3 Pin Socket Outlet 6 Amps on independent board, complete all as specified.

All as per Serial Item No. 115 above but one 3 Pin Switch Socket Outlet 15 Amps power point on independent board, with 1100 Volts, FRLS grade, 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable confirming to IS - 694 and including 1100 Volts, FRLS grade, 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable as Earth Continuity Conductor.

All as per Serial Item No. 115 above but one 3 Pin Switch Socket Outlet 15 Amps power point on independent board, with 1100 Volts, FRLS grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable confirming to IS - 694 and including 1100 Volts, FRLS grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable as Earth Continuity Conductor.

S & F Switch, Modular Type, One Module, Single Pole, One Way, 6 Amps, 230 Volts complete all as specified and as directed.

S & F Socket Outlet, 3 Pin, 6 Amps, Modular Type, Two Modules, 230 Volts, complete all as specified and as directed.

S & F Switch Socket Outlet, 3 pin, 16 Amps cum 6 Amps, Modular Type, Two Modules, Multipurpose, 230 Volts complete all as specified and as directed.

S & F Switch Modular type, one module, Single pole, one way, 16 Amps, 230 Volts complete all as specified and as directed.

S & F Ceiling Rose, PVC Body, 65 X 50 mm, Three Terminals, 230 Volts complete all as specified and as directed.

S & F in repairs SP & N Enclosure with 2 Pole and Earth Metal Plug & Socket for incorporating SP MCB complete including One MCB, SP, 20 Amps, 240 Volts complete all as specified and as directed.

M & L for Sub main wiring with 2 runs of single core 4 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 20 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor including taking down old unserviceable submain wiring and wooden battens / conduits / casing capping and making good the disturbed surfaces all as per existing complete all as specified and as directed. Note: 3 runs of 4 Sq.mm & one run of 20 mm dia PVC Conduit will be measured as one unit.

S & F Exhaust Fan, 300mm Sweep, 1400 RPM, Metal Body, Heavy Duty with Double Ball Bearing, generally Conforming to IS-2312, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50 Hz, BEE 5 Star Rated and of approved colour including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm and fixing in and making good the disturbed surface .complete all as specified and as directed.

S & F in repairs Stationary Louvers suitable for Exhaust Fan of 300mm sweep made out of powder coated aluminium anodized sheet of minimum 1 mm thick with non removable blades fixed permanently at 45 degree angle for protection from rain including aluminium wire mess for protection of birds complete all as specified and as directed.

S & F in repairs Surface & wall mounted Energy efficient LED Tube Light Fitting, of not less than 2000 Lumens output, 5700 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F in repairs Energy efficient Sleek decorative LED Mirror Light Fitting of not less than 1000 Lumens, 2 feet long Surface & Wall mounted with Acrylic / PMMA diffuser for soft glare free light with all accessories internally prewired and including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Square recessed mounted Flat Panel LED Down Light, Round type suitable for fixing in fixing in 165mm dia Ceiling Cut Out of not less than 3500 Lumens output,, 6500 K, with high transmitive diffuser for soft-light and glare free symmetrical illumination with all accessories internally prewired and including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm including taking down existing light fittings of any description and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

RAGHU RAMA PANDA (BID ID -3130955)

P Govinda Reddy Infrastructure (BID ID -3130303)

anjaliinfratech (BID ID -3134294)

N Sydeswara Rao (BID ID -3130693)

jd constructions (BID ID -3131164)

S A R CONSTRUCTIONS (BID ID -3136685)