Development of Government Taluk Hospital Varkala in Thiruvananthapuram District Kerala State including all associated MEP Services and Utilities for Health and Family Welfare Department Govt. of Kerala

Amount

BoQ Abstract : Please enter the Total Amount of sheets BoQ 2 and BoQ 3 in the respective columns.

Total amount of sheet BoQ 2 (Civil,PHE works)

Total amount of sheet BoQ 3 (MEP works)

Description of Work / Item(s)

Amount

SITE CLEARING

2.33.1 : Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Beyound 30 cm girth up to and including 60 cm girth

EARTH WORK

2.1.1 : Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed:All Kinds of soil

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.10.1.1 : Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:All kinds of soilPipes, cables etc, not exceeding 80 mm dia

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

2.26.1 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

3.6 : Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m

PILING WORK

od306223/2022_2023 : Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap).Minimum Cement content considered for pile concrete is @ 400 kg/ cum .Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used. 900 mm dia piles

20.2A.3 : Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap).Minimum Cement content considered for pile concrete is @ 400 kg/ cum . Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used. 1000 mm dia piles

od306247/2022_2023 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc.complete as per specification the direction of engineer -in-Charge. Single pile above 100 tonne and upto 150 tonne safe capacity: Initial test (Test load 2.5 times the safe capacity)

od306248/2022_2023 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification the direction of engineer -in-Charge. Single pile above 150 tonne and upto 200 tonne safe capacity: Routine test (Test load shall be 1.5 times the safe capacity)

od306249/2022_2023 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification the direction of engineer -in-Charge. Single pile above 100 tonne and upto 150 tonne safe capacity: Routine test (Test load shall be 1.5 times the safe capacity)

od306250/2022_2023 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification the direction of engineer -in-Charge. Single pile above 150 tonne and upto 200 tonne safe capacity: Initial test (Test load 2.5 times the safe capacity)

CONCRETE WORK

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.1.12 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:31/2:9 (1 ordinary portland cement : 2 Fly ash : 31/2 coarse sand : 9 graded stone aggregate 40 mm nominal size).

4.2.8 : Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)

4.4.1 : Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing.1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size)

4.12 : Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification .

4.14 : Extra for concrete work in superstructure above V level for each four floors or part thereof.

4.17 : Making plinth protection 50 mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

4.19.1.1 : Providing and laying in position ready mixed plain cement concrete, using fly ash and cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in-charge. Note : 1) Excess/less cement used than specified in this item is payable/recoverable separately. 2) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part replacement of OPC as per IS: 456. Uniform blending with cement is to be ensured in accordance with clauses 5.2 and 5.2.1 of IS : 456-2000 in the items of BMC and RMC.All works upto plinth level :M-15 grade plain cement concrete (cement content considered @ 240 kg/cum)

4.19.2.1 : Providing and laying in position ready mixed plain cement concrete, using fly ash and cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in-charge. Note : 1) Excess/less cement used than specified in this item is payable/recoverable separately. 2) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part replacement of OPC as per IS: 456. Uniform blending with cement is to be ensured in accordance with clauses 5.2 and 5.2.1 of IS : 456-2000 in the items of BMC and RMC.All works above plinth and upto floor V level:M-15 grade plain cement concrete. (cement content considered @ 240kg/ cum)

RCC WORK

5.1.3 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.2.2 : Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.3 : Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15⁰ landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

5.4 : Providing and laying up to floor five level reinforced cement concrete in kerbs, steps and the like excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (Zone - III) : 3 graded stone aggregate 20 mm nominal size)

5.5 : Reinforced cement concrete work in arches, archribs, domes, vaults, shells, folded plate and roofs having slope more than 15 up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 ( 1 cement :1.5 coarse sand(Zone III) : 3 graded stone aggregate 20 mm nominal size)

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.9.9 : Centering and shuttering including strutting, etc. and removal of form for:Arches, domes, vaults up to 6m span

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.9.16.2 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsAbove 20 cm wide

5.9.18 : Centering and shuttering including strutting, etc. and removal of form for:Small surfaces such as cantilever ends, brackets and ends of steps, caps and bases to pilasters and columns and the like

5.9.19 : Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

5.11.1 : Extra additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

5.12 : Providing, hoisting and fixing up to floor level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but excluding cost of reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone - III) : 3 graded stone aggregate 20 mm nominal size)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Additional cement requirement as per mix design shall be considered by the bidder while quoting.All work upto plinth level

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Additional cement requirement as per mix design shall be considered by the bidder while quoting nothing extra shall be paid on this account.All work above plinth level upto floor V level

5.34.1 : Extra for providing richer mixes at all floor levels. .Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).Note:-Additional cement requirement as per mix design shall be considered by the bidder while quoting nothing extra shall be paid on this account.

5.34.2 : Extra for providing richer mixes at all floor levels. Providing M-35 grade concrete instead of M-25 grade BMC/RMC. (Note: Cement content considered in M-35 is @ 350 Kg/cum).Note:-Additional cement requirement as per mix design shall be considered by the bidder while quoting nothing extra shall be paid on this account.

5.38 : Extra for R.C.C. /B.M.C/R.M.C. work above floor V level for each four floors or part thereof.

MASONRY WORK

50.6.1.1 : Solid block masonry using pre cast solid blocks ( factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part 1 of 1979 for foundation and plinth with thickness 20 cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

50.6.1.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

50.6.1.5 : Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

50.6.1.6 : Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level thickness 20cm and above in : CM 1:6 ( 1 cement : 6 coarse sand sand) etc complete

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

50.6.6.3 : Hollow block masonry using pre cast solid blocks ( Factory made ) of size 40x20x10cm or nearest available size confirming to IS 2185 part I of 1979 for Super structure above floor two level upto floor five level for 10cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand ) including cost of scaffolding etc complete

6.1.1 : Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

6.4.2 : Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:Cement mortar 1:6 (1 cement : 6 coarse sand)

6.5 : Extra for brick work/ AAC block masonry/Tile brick masonry in super structure above floor V level, for each four floors or part thereof by mechanical means.

6.15 : Extra for providing and placing in position 2 Nos 6 mm dia M.S bars at every third course of half brick masonry.

6.34.2 : Brick work with non modular fly ash lime bricks (FALG Bricks) conforming to IS: 12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in polymermodified adhesive mortar/Cement mortar 1:6 (1 cement : 6 coarse sand) as per manufacturer recommendation.

6.38 : Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above floor 2 level up to floorV level in cement mortar 1:4 (1 cement :4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

6.47 : Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor Vlevel with RCC band at sill level and lintel level with approved block laying polymermodified adhesive mortar all complete as per direction of Engineer-in-Charge. (Thepayment of RCC band and reinforcement shall be made for seperately).

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

60.7.1 : DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site

FLOORING

11.3.1 : Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate)finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate

11.20.3 : Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand).Dark shade pigment using ordinary cement

11.26.1 : Kota stone slab flooring over 20 mm ( average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)25 mm thick

11.37 : Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

11.40 : Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer) of Ist quality conforming to IS: 15622 of approved make in all colours, shades, except white, Ivory, Grey Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

11.46.2 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

11.56.1 : Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

8.2.2.1 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shadeArea of slab upto 0.50 sqm

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

8.3.2 : Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work

8.4.11 : Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign with 7years warranty manufactured as per IRC :67 made of Type IV micro prismatic grade sheeting fixed over aluminium sheeting, 2 mm thick/ aluminium composit material sheeting 4 mm thick with suitable back supporting frame of MS angle 25x25x3 and supported on GI pipe pole 50mm NB confirming to IS 1239 firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc.75 cm triangle

8.4.12 : Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign with 7years warranty manufactured as per IRC :67 made of Type IV micro prismatic grade sheeting fixed over aluminium sheeting, 2 mm thick/ aluminium composit material sheeting 4 mm thick with suitable back supporting frame of MS angle 25x25x3 and supported on GI pipe pole 50mm NB confirming to IS 1239 firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc.50cmx 60 cm rectangular (Single chevron etc.)

8.5 : Extra for providing opening or required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

8.7.A : Providing and erecting overhead signs with retro reflectorised sign with 7 years warranty manufactured as per IRC67 made of Hign Intensity Micro Prismatic (Type IV ) grade sheeting fixed over corrosion resistant 2mm thick aluminium alloy sheet with vertical and lateral clearance given in clause 802.2 and 802.3 and installed as per clause 802.7 over a designed support system of aluminium alloy or galvanised steel trestles and trusses of sections and type as per structural design requirements and approved plansTruss and Vertical Support

8.10.2 : Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in Charge and finished smooth.Granite Stone of approved shade

8.14.1.1 : Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade :(To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :Red sand stone - exposed face fine dressed with rough backing.70 mm thick

8.16 : Reinforced cement concrete M-15 grade boundary pillars of standard design as per IRC:25-19767, fixed in position including finishing and lettering but excluding painting .

8.21 : Providing, fencing and erecting 50 mm dia painted steel pipe railing in 3 rows on precast M20 grade RCC vertical posts1.8 metres high (Tubular Steel Railing on Precast RCC Posts, 1.2 m High Above Ground Level) with 3 holes 50 mm dia for pipe, fixed 2 metres centre to, complete as per approved drawing

od169744/2022_2023 : Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

od169745/2022_2023 : Providing and laying Antiskid Ceramic floor tiles 300x300x7 mm of Ist quality conforming to IS : 15622 of approved make,shade,and pattern laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc.including cost and conveyance of all materials,labour charges,lead,lift etc, complete as directed by the Engineer-in-Charge at all levels.

od169747/2022_2023 : Extra for Providing grip grooves 3 nos 3mmx3mm in granite threads including cost and conveyance of all machinery,materials, labour charges, etc and making the sufrace clean complete at all levels as directed by the Engineer-in-Charge( Cost of granite slab will be paid separately )

od169748/2022_2023 : Providing fixing flooring transition profile at transitions between tile, vinyl and granite flooring of approved sizes and design as per manufacturer’s standard. The finish of the profile is Satin Stainless Steel of grade 304 (AISI 304) or as approved by the Engineer in charge . The profile is to be fixed with mortar or adhesive or screws as per manufacturer’s specification and as approved by the architect or client.

od169749/2022_2023 : Providing laying 2mm thick polyurethene reinforced laminated antistatic, antifungal, antibacterial vinyl flooring and skirting, including self levelling upto 3mm thick with cementitious material ,flexibility less than 20mm, residual indentation less than 0.1 mm electrical behaviour less than 2kV, of approved colour, size and texture over the floor surface to proper level, line using adhesives as per manufacturer's specification including joint treatment, coving cum pvc capping, welding etc complete as directed by the Engineer-in- Charge at all levels.The rate is inclusive of cost of all materials,upto 3 mm thick self levelling, welding all joints, labour, lead, lift etc. complete as directed by the Engineer-in-Charge at all levels

JOINERY & PARTITION WORK

9.21.1 : Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non- decorative Type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

50.9.1.1 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood

50.9.15.1 : Supplying and fixing 200 mm Aluminium aldrop

9.53 : Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

9.62.2 : Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete:250x16mm

9.70.1 : Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:125x64x1.90 mm

9.76 : Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

9.83 : Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

9.84 : Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

9.90.1 : Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete.Size 40 mm

9.92.1 : Providing and fixing chromium plated brass handles with necessary screws etc. complete:125 mm

9.96.1 : Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:300x16 mm

9.97.1 : Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:300x10 mm

9.97.3 : Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:200x10 mm

9.100.1 : Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:125 mm

9.101.2 : Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper

9.103 : Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS: 1868) aluminium lever handles of approved quality with necessary screws etc . complete.

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

od169751/2022_2023 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With high performance glass panes of 6 mm thickness meeting GRIHA compliance of overall value "VLT 34%, SHGC 0.34.

od169752/2022_2023 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With high performance glass panes of 6 mm thickness meeting GRIHA compliance of overall value "VLT 40%, SHGC 0.45.

od169753/2022_2023 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item): With Toughened glass panes of 6 mm thickness

od169754/2022_2023 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item): With toughened glass of 5.0 mm thickness

od169755/2022_2023 : Providing and fixing powder coated Aluminium louvered Ventilators (minimum thickness of powder coating 50 microns) of approved colour HINDALCO or equivalent 9771, with 5mm thick frosted glass of approved make for aluminium U channel louvers including necessary grooves in frames for fixing glass etc. complete. Providing and fixing powder coated Aluminium louvered Ventilators (minimum thickness of powder coating 50 microns) of approved colour HINDALCO or equivalent 9771, with 5mm thick frosted glass of approved make for aluminium U channel louvers including necessary grooves in frames for fixing glass etc. complete.

od169756/2022_2023 : Provided and fixing dusted/frosted glass film of make 3M/Avery Dennison or equivalent of approved shade (overall thickness of Film + Adhesive shall be approx. 120 microns) on glasswith customized prints with HP latex based high quality prints. The film shall install with self-adhesive and bubble-free installation to be done on clean glass .The rate shall include the cost and conveyance of all materials, labour charges, scaffolding, lead ,lift, sundries, print, wastage ,design, operations etc complete as directed by the Engineer in charge at all levels.

od169759/2022_2023 : Providing and fixing hardwares for Handicaped door(Excluding door frame and panel).The shutter to be provided with cylindrical knob lock with rose diameter 75 mm and SS matt finished kick plate of dimension 300 MM X 1050 MM X 1MM including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing etc. complete as directed by the Engineer-in-Charge at all levels:

od175758/2022_2023 : Providing and fixing of Hollow metal steel doors double leaf or single leaf made of pressed galvanized steel confirming to IS 277 with the following specification. Doors shall be with vision glass and louver as a part of complete assembly. Door frame shall be single rebate grooved profile of size 125 x 55mm made out of minimum 1.20mm (18gauge) thick galvanized steel sheet as per manufacturer recommendation. Frames shall be mitered and field assembled with self tabs. Frames to have inbuild grooved sealing system and shall be site fitted with PVC seal as standard. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Frames shall be filled with puff / honey comb infill material. Door leaf shall be 46mm thick fully flush double skin door, with or without vision lite. Door leaf shall be manufactured from minimum 0.8mm (22guage) thick galvanized steel sheet. The internal construction of the door should be rigid reinforcement pads for receiving appropriate hardware. The infill material shall be resin bonded honeycomb core/ equivalent material. All doors shall be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending radius of 1.4mm. For pair of doors integrated astragals has to be provided on the meeting stile for both active and inactive leaf. Vision lite wherever applicable should be provided as per manufacturers recommendation with a clipon arrangement. The glass should be minimum 5mm clear toughened glass of relevant rating of the door. All doors and frames shall be finished Pure Polyester Powder coated and shall have passed minimum 500 hours of salt sprey test. Measurement shall be done in sqm area of door as per technical specification for payment irrespective of door sizes. Rate shall include supply and installation of door and hardware as a complete assembly including vision glass, louvers etc complete as mentioned in the door and hardware schedule complete as per manufacturer recommendation and as directed by Engineer in charge at all levels.

21.2.2 : Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides

21.3.2 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

21.4.1 : Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors including cost of cutting floors, embeding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer -in- Charge.With stainless steel cover plate minimum 1.25 mm thickness

21.5 : Providing and fixing powder coated aluminium work ( minimum thickness of powder coating 50 micron) consisting of tee /angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-Charge ( level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately ).

21.11.1 : Providing and fixing stainless steel (SS 304 grade) adjustable friction window stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer - in-Charge complete.205 x 19 mm

21.12.2 : Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0mm thick & 2100 mm long with S.S. screws etc. complete as per direction of Engineer -in-Charge.Powder coated minimum thickness 50 micron aluminium tubular handle bar

21.12.3 : Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0mm thick & 2100 mm long with S.S. screws etc. complete as per direction of Engineer -in-Charge.Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar

21.13 : Providing and fixing 100 mm brass locks ( best make of approved quality ) for aluminium doors including necessary cutting and making good etc. complete

21.14 : Providing and fixing anodised aluminium ( anodised transparent or dyed to required shade according to IS: 1868. Minimum anodic coating of grade AC 15) sub frame work for windows and ventilators with extruded built up standard tubular section of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia and size (Dash fastener to be paid for separately)

21.15.2 : Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary necessary screws etc. complete.Powder coated minimum thickness 50 micron aluminium

21.17 : Providing and fixing anodised aluminium grill ( anodised transparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.(Only weight of grill to be measured for payment ).

21.18 : Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately)

9.105.1 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.75 mm overall thickness partition with 12.5 mm thick double skin fire rated board conforming to IS : 2095 : part I

9.105.3 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.66 mm overall thickness Partition with 8 mm thick double skin Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process with Compressive Strength 225 kg/sq cm, Bending Strength 100 kg/sq cm

9.105.4 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.66 mm overall thickness partition using 8 mm thick double skin non - asbestos multipurpose cement board reinforced with cellulose fibre manufactured through autoclaving process (High pressure steam cured) as per IS : 14862 with suitable fibre cement screws

9.105.5 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.66 mm overall thickness partition using 8 mm thick double skin multipurposecement bonded wood particle board manufactured as per IS: 14276 with suitablecement bonded board screws

9.114.1 : Providing and fixing magnetic catcher of approved quality in cupboard/ward robe shutters, including fixing with necessary screws etc. complete.Triple strip vertical type

9.116 : Providing and fixing sliding arrangement in racks/ cupboards/cabinets shutter by with stainless steel rollers to run inside C or E aluminium channel section ( The payment of C or E channel shall be made separately

9.121 : Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross- section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminated shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

9.122.2 : Providing and fixing to existing door frames.30 mm thick Fiberglass Reinforced Plastic (F.R.P) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used all filler material throughout the hollow panel, casted monoolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS : 14856, complete as per direction of Engineer-in-charge.

9.126.1 : Providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows ( area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled and glazed shutters 25 mm to 40 mm thick.Marine plywood conformingto IS : 710

9.136 : Providing and fixing fire resistant door frame of section 143x57 mm having built in rebate made out of 16 SWG G.I. sheet ( zinc coating not less than 120 gm/ sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer -in-charge (Dash fastener to be paid for separately ).

9.138.1 : Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 60 minutes of fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.With clear fire resistant glass panes 6 mm thick of approved brand, having minimum 60 minutes fire resisitance

9.139 : Providing and fixing panic bar / latch (Double point ) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer -in-charge, all complete.

9.157.1 : Providing and fixing Pre-laminated medium density fibre board IS:14587:1998 marked, with one side decorative lamination other side balancing lamination Grade-I (exterior grade) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately).Pre-laminated with decorative lamination one side and other side balancing laminaion exterior Grade-I MDF Board 18mm thick confirming to IS:14587.

9.157.2 : Providing and fixing Pre-laminated medium density fibre board IS:14587:1998 marked, with one side decorative lamination other side balancing lamination Grade-I (exterior grade) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately).Pre-laminated with decorative lamination one side and other side balancing lamination exterior Grade-I MDF Board 25mm thick confirming to IS:14587.

9.158.1 : Providing and fixing in wall lining medium density fibre board IS: 14587: 1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete.12 mm thick.

9.159 : Providing and fixing 25mm thick pre-laminated medium density fibre board exterior grade (Grade-I) IS:14587:1998 marked one side decorative and other side balancing lamination for cupboard shutters edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand including ISI marked nickeled plated bright finishing M.S. piano hinge IS: 3818 marked with necessary screwed complete.

9.161 : Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontalside & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mmthick GI sheet ( Zinc coating not less than 120gm/m2) suita2ble for mounting 120min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineralwool Insulation having density min 96Kg/m2 . The frame will have a provision ofG.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style ofsize M10 x 80 ) suitable for fixing in the opening along with Factory madeTemplate for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire ratedglazed shutter . The frame shall be finished with a approved fire resistant primeror Powder coating of not less than 30 micron in desired shade as per thedirections of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded

9.162 : Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 minFire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certifiedas per laboratory approved by Engineer-in-charge, with suitable mounting ondoor frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mmwide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet(zinc coating not less than 120gm/m²) duly filled mineral wool insulation havingdensity min 96 kg/m³ and fixing with necessary stainless steel ball bearing hingesof size 100x89x3mm of approved make, including applying a coat of approvedfire resistant primer or powder coating not less than 30 micron etc all completeas per direction of Engineer-in-charge (panelling to be paid for seperately

9.164 : Providing and fixing glazing in fire resistant door shutters, fixed panels & partitionsetc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mmfrom the edges and 150 mm c/c , including applying a coat of approved fire resistantprimer/powder coating of not less than 30 micron on G.I. beading, & special ceramictape of 5 x 20 mm size etc complete in all respect as per direction of Engineer-incharge.The glass shall be clear, toughened, interlayered, non-wired fire resistant having11 mm thickness of approved brand with 120 minutes of fire resistance both integrity &radiation control (EW120) and minimum 15 min of insulation (EI15) and having a soundreduction of ?37dB and LT of 86%. Glass shall be compliant to class 2(B)2 category ofImpact Resistance as per EN 12600. The glass should be manufactured in UL & TUVaudited Facility and including UL-EU Certification.The maximum glazing size cannotbe more than 1100 mm x 2200 mm (w x h) or 2.42 sq mts in total area. The test report forthe complete system (Glazed Door or Partition) will be considered valid only if it containsthe stamp and signature of the authorized signatory from the glass manufacturer.(Actual glass size is to be measured at site for payments).

9.165.1 : Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

9.165.2 : Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.100mm

26.45 : Supplying and installation of moisture resistant/fire resistant 6 mm thick Heavyduty fiber cement board (High pressure steam cured) conforming to IS14862:2000 of category III type B as per standard sizes fixed with self-drilling /taping screws. Screws shall be of counter sunk rib head of 1.60mm to 4 mmthick of 8 to 10 gauge of length varying from 25 to 45 mm.

STEEL & ROOFING WORK

10.2 : Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

10.6.1 : Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

10.7 : Providing and fixing ball bearing for rolling shutters.

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

10.16.2 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes

10.17 : Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

12.1.2 : Providing corrugate G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.80 mm thick with zinc coating less than 275 gm/m2

12.4.1 : Providing ridges or hips width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.0.80 mm thick with zinc coating not less than 275 gm/m2

12.5.1 : Providing valleys of 90 cm wide overall in plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limper and bitumen washers complete:1.60 mm thick with zinc coating not less than 350 gm/ m2

12.6.1 : Providing and fixing of 40 cm overall width plain G.S. Sheet fixed with polymer coated J or L hooks, bolts and nuts, G.I. limpet and bitumen washer complete, bent to shape and fixed in wall with cement mortar 1:3 ( 1 cement : 3 coarse sand).1.00 mm thick with zinc coating not less than 275 gm/ m2

12.7.1 : Providing and fixing 15cm wide, 45 cm overall semi circular plain G.S. sheet gutter with iron brackets 40x3 mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete.0.80 mm thick with zinc coating not less than 275 gm/m2

12.41.2 : Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter

12.42.1.2 : Coupler110 mm

12.42.2.2 : Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionSingle pushfit Coupler110 mm

12.42.4.2 : Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionSingle tee without door110x110x110 mm

12.42.6.2 : Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionShoe (Plain)110 mm Shoe

12.43.2 : Providing and fixing unplasticised- PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc. complete.110 mm

50.12.2.1 : Providing & fixing Poly carbonate corrugated sheet 0.8 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling / self tapping screw of size (5.5x55 mm) with EPDM seal complete upto any pitch in horizontal/ vertical/ curved surface, but excluding the cost of purlins, rafters, trusses, and including cutting to size shapes where ever required.

od167880/2022_2023 : Supplying and fixing PVC rain water gutter of 200 mm size including necessary fittings such as clamps,,screw, end stopper etc. including cost of all materials labour charges scaffolding etc

od169750/2022_2023 : Providing and Fixing Multi cell/tight cell polycarbonate sheet Panel System with16mm thick (minimum) single panel . The weight of the panel shall not be less than 3250 gram per square meter. Panel Width shall not be less than 1040mm to ensure best performance for wind uplift, vibration, oil canning and visual appearance. The panels shall be uniform in color with an integral Tight-Cell core. In a cross section, the core shall be constructed of tight cells not to exceed 4mm x 4mm. Panels shall be manufactured with Vertical Standing Seam at both sides of the panel. Snap-on connector to interlock the panels shall have a grip-lock tooth locking mechanism to ensure maximum uplift capability. Panels shall be secured with snap-on connectors with / without continuous double wall Aluminium spacer along the standing seam. Panel shall be factory sealed/end welded panels with additional End-cap/Aluminium U-Profile (mill finish) for ends. Panels shall be co-extruded UV protected. Panel shall be co-extruded with special anti glare compound to make it anti-glare/soft light to prevent glare and sun streaks. All aluminium sections to have recycled content of 15-30%.VLT>50% SHGC 0.27. The rate shall includes ,cost and conveyance of all materials,Handling of machineries and electrical charges etc. labour charges,lead,lift etc. complete as per technical specification and as directed by the Engineer in charge at all levels .The above work shall be carried out by an agency having sufficient experience in concerned work and should ensure a guarantee for any defective installation,material composition and water and weather tightness for a period of 10 years from the date of completion of the said work .only skilled and experienced persons shall be employed for this purpose.

CEILING WORK

12.24.3.1 : Providing and fixing insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately):Flame retardant face insulating board12 mm thick

12.27.4.1 : Extra for Circular cutting including wastages in ceiling with:Flame retardant face insulating board12 mm thick

12.32 : Extra for sunk or raised mouldings in the plaster of Paris (Gypsum anhydrous) ceiling.Extra for sunk or raised mouldings in the plaster of Paris (Gypsum anhydrous) ceiling .

12.53 : Providing and Fixing 15 mm densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture spintone /cosmos /Hexa or equivalent of size 595x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main 'T' runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross "T" of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main 'T' of size 24 x 28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main'T' at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross 'T' of length 600 mm and size 24x28 mm made of 0.33 mm thick (minimum) sheet to be inter locked at middle of the 1200x600 mm panel to from grid of size 600x600 mm, resting on periphery walls/partitions on a Perimeter wall angle pre-coated steel of size (24x24x3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture (Spintone / Cosmos/hexa) in the grid, including cutting / making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever require. Main 'T' runners to be suspended from ceiling using G.I slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size of 85x30x0.8 mm, spaced at 1200mm centre to centre along main 'T' bottom exposed with 24 mm of all T- sections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by by engineer-in-charge. Note:- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm. The calcium silicate ceiling tiles shall have NRC. value of 0.50 (Minimum), light reflection > 85% non - combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity < 0.043 w/m 0 KC.

12.54.2 : Providing and fixing GI Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of sixe38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring 'T' with :GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/sqm(both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.

26.8 : Providing and fixing 50 mm thick extruded polystyrene rigid insulation board ofrequired size under deck on ceiling surface, complying with ISO 4898:2008 &ASTM C 578-08b - type VI, having thermal conductivity of 0.0289 W/m K as perASTM C 578 (measured as per IS 3346), compressive strength of > 350 kPa listedas per ASTM D 1621, density of 34-36 kg/cum as per ASTM D 1622, waterabsorptions 1% by volume as per ASTM D 2842, oxygen index of 24.1 to 28.1listed as per ASTM D 2863, cell size 0.4 mm of dia (max) as per ASTM D 3576. Fireretardent property as per DIN 4102, Part 1 of class B2 and as per ASTM E84 classA, fixed with suitable water based adhesive and fastener, complete in all respectas per the direction of Engineer-in-Charge.

26.27.3 : Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ?85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.With 16 mm thick beveled tegular mineral fibre Anti-microbial false ceiling tileconfirming to ISO 5 (class 100 ) specifications

FINISHING WORK

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.1.2 : 12 mm cement plaster of mix:1:6 (1 cement : 6 fine sand).

13.7.1 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

13.7.2 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:4 ( 1 cement : 4 fine sand)

13.9.2 : Cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement.20 mm cement plaster

13.13 : 12 mm cement plaster 1:2 ( 1 cement : 2 stone dust)

13.16.1 : 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

od169740/2022_2023 : 6 mm cement(with fly ash) plaster of mix: 1:3 ( 1 cement : 3 fine sand)

od169741/2022_2023 : 12 mm cement(with fly ash) plaster finished with a floating coat of neat cement of mix: 1:3 ( 1 cement : 3 fine sand)

od169742/2022_2023 : 12 mm cement(with fly ash) plaster of mix: 1:4 ( 1 cement : 4 fine sand)

13.21 : Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

13.22 : Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

13.28.2 : 12 mm thick plain cement mortar bands in cement mortar 1:4 ( 1 cement : 4 fine sand) :Sunk Band

13.28.3 : 12 mm thick plain cement mortar bands in cement mortar 1:4 ( 1 cement : 4 fine sand) :Raised Band

13.28.4 : 12 mm thick plain cement mortar bands in cement mortar 1:4 ( 1 cement : 4 fine sand) :Moulded Band

13.33.2 : Pointing on stone work with cement mortar 1:3 ( 1 cement : 3 fine sand):Raised and cut pointing

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.44.1 : Finishing walls with water proofing cement paint of required shade:New work (Two or more coats applied @ 3.84 kg/10 sqm)

13.45.1 : Finishing walls with textured exterior pint of required shade:New work (Two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.50.3 : Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron /steel works

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.61.1 : Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.62.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.85.3 : Applying priming coats with primer of approved brand and manufacture, having low VOC ( Volatile Organic Compound) content.With water thinnable cement primer on walls surface having VOC content less than 50 grams / litre

13.114 : Melamine polishing on wood work (one or more coat).

FAÇADE WORKS

25.1 : Providing and supplying aluminium extruded tubular and other aluminium sectionsas per the architectural drawings and approved shop drawings , the aluminiumquality as per grade 6063 T5 or T6 as per BS 1474,including super durable powdercoating of 60-80 microns conforming to AAMA 2604 of required colour and shadeas approved by the Engineer-in-Charge. ( The item includes cost of material suchas cleats, sleeves, screws etc. necessary for fabrication of extruded aluminiumframe work. Nothing extra shall be paid on this account).

25.2 : Designing, fabricating, testing, protection, installing and fixing in position semi(grid) unitized system of structural glazing (with open joints) for linear as well ascurvilinear portions of the building for all heights and all levels, including:a) Structural analysis & design and preparation of shop drawings for the specifieddesign loads conforming to IS 875 part III (the system must passed the proof testat 1.5 times design wind pressure without any failure), including functional designof the aluminum sections for fixing glazing panels of various thicknesses, aluminiumcleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clampsetc., structural and weather silicone sealants, flashings, fire stop (barrier)-cumsmokeseals, microwave cured EPDM gaskets for water tightness, pressureequalisation & drainage and protection against fire hazard including:b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3Dimentional movement for achieving perfect verticality and fixing structural glazingsystem rigidly to the RCC/ masonry/structural steel framework of building structureusing stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetalliccontacts with nuts and washers etc. of stainless steel grade 316, of the requiredcapacity and in required numbers.c) Providing and filling, two part pump filled, structural silicone sealant and onepart weather silicone sealant compatible with the structural silicone sealant ofrequired bite size in a clean and controlled factory / work shop environment ,including double sided spacer tape, setting blocks and backer rod, all of approvedgrade, brand and manufacture, as per the approved sealant design, within and allaround the perimeter for holding glass.d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thickand of sizes, shapes and profiles, as required as per the site conditions, to seal thegap between the building structure and all its interfaces with curtain glazing tomake it watertight.e) Making provision for drainage of moisture/ water that enters the curtain glazingsystem to make it watertight, by incorporating principles of pressure equalization,providing suitable gutter profiles at bottom (if required), making necessary holesof required sizes and of required numbers etc. complete. This item includes costof all inputs of designing, labour for fabricating and installation of aluminium grid,installation of glazed units, T&P, scaffolding and other incidental charges includingwastages etc., enabling temporary structures and services, cranes or cradles etc.as described above and as specified. The item includes the cost of getting all thestructural and functional design including shop drawings checked by a structuraldesigner, dully approved by Engineer-in-charge.The item also includes the cost of all mock ups at site, cost of all samples of theindividual components for testing in an approved laboratory, field tests on theassembled working structural glazing as specified, cleaning and protection till thehanding over of the building for occupation. In the end, the Contractor shall providea water tight structural glazing having all the performance characteristics etc. allcomplete as required, as per the Architectural drawings, as per item description,as specified, as per the approved shop drawings and as directed by the Engineerin-Charge.Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extrudedaluminium section capping for fixing in the grooves of the curtain glazing andvermin proof stainless steel wire mesh shall be paid for separately under relevantitems under this sub-head. However, for the purpose of payment, only the actualarea of structural glazing (including width of grooves ) on the external face shallbe measured in sqm. up to two decimal places.Note:-2. The following performance test are to be conducted on structural glazingsystem if area of structural glazing exceeds 2500 Sqm from the certified laboratoriesaccreditated by NABL(National Accreditation Board for Testing and CalibrationLaboratories), Department of Science & Technologies, India. Cost of testing ispayable separately. The NIT approving authority will decide the necessity of testingon the basis of cost of the work, cost of the test and importance of the work.Performance Testing of Structural glazing systemTests to be conducted in the NBL Certified laboratories1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) & (+50pa to+300pa) as perASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr”2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testingmethod for a range up to 2000 ml.”3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01-05 testingmethod for a range upto 2000 ml”4. Structural Performance Deflection and deformation by static air pressure test(1.5 times desing wind pressure without any failure) as per ASTME-330-10 testingmethod for a range upto 50 mm”5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method forQualitative test” Tests to be conducted on site6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi)upto 2000ml”

od169743/2022_2023 : Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 34 %, Light reflection internal 8%, light reflection external 23 %, shading coefficient (0.39),SHGC- 0.34 and U value of 3.9 W/m2 degree K etc. The properties of performance glass shall be adjusted as per the GRIHA requirement and manufacturer specification.

25.4 : Extra for openable side / top hung vision glass panels (IGUs) including providingand supplying at site all accessories and hardwares for the openable panels asspecified and of the approved make such as heavy duty stainless steel frictionhinges, min 4 -point cremone locking sets with stainless steel plates, handles,buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts,washers etc. all complete as per the Architectural drawings, as per the approvedshop drawings, as specified and as directed by the Engineer-in-Charge.

25.5 : Providing,fabricating and supplying shadow box of required size and shape, for fixing in the spandrel portion of the structural glazing, in linear as well as curvilinear portions of the building by providing semi - rigid, inorganic, non- combustible fibre glass wool insulation 50 mm thick, conforming to IS: 8183 and BS: 3958 part 5. The insulation layer shall have facing (factory bonded on surface # 1 of the fibre glass insulation layer), of black non-woven fibre glass tissue of nominal thickness 0.5mm and nominal mass not less than 60 gm/ sqm, made of randomly oriented glass fibres distributed in a binder by a wet-lay process including fixing 1.5 mm thick solid aluminum sheet backing using, 6 mm thick cement board including SS rivets, nuts,bolts, washers etc complete.

25.6 : Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc., all complete for the required performance as specified, as per the architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in - Charge. For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area of grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (Payment for fixing of Spandrel Glass panels in the curtain glazing is included in cost of relevent item*).(ii) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face #2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35%, Light reflection internal 10 to 15%, light reflection external 10 to 20%, shading coefficient (0.25 - 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

25.7 : Designing, fabricating, testing, installing and fixing in position Curtain Wall withAluminium Composite Panel Cladding, with open grooves for linear as well ascurvilinear portions of the building , for all heights and all levels etc. including:a) Structural analysis & design and preparation of shop drawings for pressureequalisation or rain screen principle as required, proper drainage of water to makeit watertight including checking of all the structural and functional design.b) Providing, fabricating and supplying and fixing panels of aluminium compositepanel cladding in pan shape in metalic colour of approved shades made out of4mm thick aluminium composite panel material consisting of 3mm thick FR grademineral core sandwiched between two Alumini um sheets (each0.5mm thick). Thealuminium composite panel cladding sheet shall be coil coated, with Kynar500based PVDF / Lumiflon based fluoropolymer resin coating of approved colourand shade on face # 1 and polymer (Service) coating on face # 2 as specified usingstainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backerrods etc.c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanisedwith serrations and serrated washers to arrest the wind load movement, fasteners,SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators toprevent bi-metallic contacts all complete required to perform as per specificationand drawing The item includes cost of all material & labour component, the cost ofall mock ups at site, cost of all samples of the individual components for testing inan approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wallwith aluminium composite panel cladding till the handing over of the building foroccupation. Base frame work for ACP cladding is payable under the relevantaluminium item.s The Contractor shall provide curtain wall with aluminiumcomposite panel cladding, having all the performance characteristics all complete, as per the Architectural drawings, as per item description, as specified, as per theapproved shop drawings and as directed by the Engineer-in-Charge.However, for the purpose of payment, only the actual area on the external face ofthe curtain wall with Aluminum Composite Panel Cladding (including width ofgroove) shall be measured in sqm. up to two decimal places.

WATERPROOFING WORKS

22.4.1 : Providing and Placing in position suitable PVC water stops conforming to IS : 12200 for construction / expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete:Serrated with central bulb ( 225 mm wide, 8-11 mm thick)

22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

22.22 : Providing and mixing integral crystalline admixture for waterproofing treatment toRCC structures like basement raft, retaining walls, reservior, sewage & watertreatment plant, tunnels / subway and bridge deck etc.. at the time of transportingof concrete into the drum of the ready-mix truck , using integral crystalline [email protected]% (minimum) to the weight of cement content per cubic meter of concrete)or higher as recommended by the manufacturer's specification in reinforced cementconcrete at site of work. The material shall meet the requirements as specified inACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 90%,compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostaticpressure. The crystalline admixture shall be capable of self-healing of cracks up toa width of 0.50mm. The work shall be carried out all complete as per specificationand the direction of the Engineer-in-charge. The product performance shall carryguarantee for 10 years against any leakage.

22.22A : Providing and applying fibre reinforced elastomeric liquid water proofing membranewith resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top ofconcrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming ofelastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and twocoats of undiluted elastomeric waterproofing liquid (dry film thickness of completeapplication/system not less than 500 microns). The operation shall be carried outafter scrapping and properly cleaning the surface to remove loose particles withwire brushes, complete in all respect as per the direction of Engineer-in-Charge.

22.23.1 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer in- charge. The product performance shall carry guarantee for 10 years against any leakage.For vertical surface two coats @0.70 kg per sqm

22.23.2 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer in- charge. The product performance shall carry guarantee for 10 years against any leakage.For horizontal surface one coat @1.10 kg per sqm.

22.26 : Providing and applying of swellable type water stop tape, 19mm x 25mm thick inlinear meter (expansive nature) for construction joints treatment of RCC structuresuch as raft slab, retaining walls, water storage tank and at the junctions of raftslab with the retaining walls etc.. After cleaning the surface, one coat of requiredprimer for swellable water stop tape shall be applied throughout the length of thejoint @3.78 litre per 240 running meter. Over the primed surface swellable typewater stop tape shall be placed. The work shall be carried out all complete as perspecification and the direction of the engineer-in-charge. The product performanceshall carry guarantee for 10 years against any leakage.

LANDSCAPING WORKS

30.2.2 : Supplying and stacking of good earth at site including royalty and carriage upto 5 k.m. lead complete (earth measured in stacks will be reduced by 20% for payment).

30.2.3 : Supplying and stacking sludge at site including royalty and carriage upto 5 k.m. lead complete (sludge measured in stacks will be reduced by 8% for payment).

30.2.4.1 : Supplying and stacking at site dump manure from approved source, including carriage upto 5 k.m. lead complete (manure measured in stacks will be reduced by 8% for payment) :Screened through sieve of I.S. designation 20 mm

30.2.8 : Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

30.2.9 : Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

30.2.14.3 : Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :Holes 60 cm dia, and 60 cm deep

30.2.17.1 : Making tree guard 53 cm dia and 1.3 m high as per design from empty coal tar drums, supplied free by the department, including providing and fixing 2 nos M.S. sheet rings 50 x 0.5 mm fixed with rivets complete in all respects including painting inside and outside of tree guard with:A coat of coal tar

30.2.20 : Filling mixture of earth and sludge or manure in the desired proportion in trenches, flooding with water and leveling (cost of supplying earth and sludge or manure and mixing excluded).

30.2.25 : Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m. lead complete (cattle manure measured in stacks will reduced by 8% for Payment).

od168683/2022_2023 : Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material&rsquo;s as per direction of officer in charge (excluding cast of plant water) - Trees Plant

od168684/2022_2023 : Providing and displaying of Tree plants in Earthen pot or in ground as per direction of the officer-in-charge.

od168686/2022_2023 : Providing and fixing solid bio degradable organic waste compost bins with protection grill and roof

ROAD WORK

16.68 : Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

16.78.1 : Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.With Material conforming to Grade - I ( size range 75 mm to 0.075 mm) having CBR Value- 30

16.79 : Providing , laying spreading and compacting graded stone aggregate ( size range 53 mm to 0.075 mm) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub - base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer - in- Charge.

od187794/2022_2023 : Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or road and parking etc, of required strength, thickness size/ shape, made by table vibratory method using PU mould, laid in required colour pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-40 grade with approved color design and pattern.

8.1.A : Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC Using Concrete Mixer on M-10 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 409

SANITARY, WTP works etc

17.1.1 : Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litter low level white P.V.C.flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever require:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

17.10.1.1 : Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink with drain board510x1040 mm bowl depth 250 mm

17.10.2.2 : Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink without drain board610x460 mm bowl depth 200 mm

17.22A : Providing and fixing CP Brass 32mm size Bottle trap of approved quality & make and as per the direction of Engineer in charge.

17.28.1.1 : Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. waste fittings complete.Semi rigid pipe32 mm dia

17.32.2 : Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357 mm

17.34.1 : Providing and fixing toilet paper holder:C.P. brass

od182986/2022_2023 : Providing and fixing sink cock of approved quality conforming to IS 8931, with GRIHA water conservation mechanism as approved by the engineer in charge at all levels.The flow-rates of sink cock shall be 4 LPM or as per GRIHA water conservation requirement .

17.72 : Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms

17.73.1 : Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm. weighing not less than 170 gms

18.16.2 : Providing and fixing brass stop cock of approved quality :20 mm nominal bore

18.17.1 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

18.17.1A : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :20 mm nominal bore

18.17.2 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

18.17.3 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm nominal bore

18.17.4 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore

18.17.5 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :65 mm nominal bore

18.17.6 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :80 mm nominal bore

18.18.2 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:20 mm nominal bore

18.18.3 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:25 mm nominal bore

18.19.4.1 : Providing and fixing gun metal non-return valve of approved quality (screwed end):50 mm nominal boreHorizontal

18.31.1.1 : Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately):100 mm diameterClass I

18.53.1 : Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

18.55.2 : Providing and fixing PTMT stop cock of approved quality and colour.20 mm nominal bore, 89 mm long, weighing not less than 88 gms

18.58.1.1 : Providing and fixing PTMT grating of approved quality and colour.Circular type100 mm nominal dia

18.59.1 : Providing and fixing C.I double acting air valve of approved quality with bolts, nuts, rubber insertion etc. complete ( The tail pieces, tapers etc. if required will be paid separately):50 mm dia

18.77 : Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

19.7.1.1 : Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.8.1.1 : Extra for depth for manholesSize 90x80 cmWith common burnt clay F.P.S. ( non modular ) bricks of class designation 7.5

19.15.1 : Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) as per standard design.With 20x20 mm square bar

19.18.1 : Supplying and fixing C.I with out frame for manholes:455 x 610 mm rectangular C.I cover ( light duty ) the weight of the cover to be no less than 23 kg

19.19.1.2 : Providing and fixing in position Pre-cast R.C.C. manhole cover and frame of required shape and approved quality.L D - 2.5Square shape 450 mm internal dimensions

19.19.4.1 : EHD - 35Circular shape 560 mm internal dia

19.30.1.1 : Constructing brick masonry chamber for underground C.I. inpection chamber and bends with bricks in cement mortar 1:4 ( 1 cement: 4 coarse sand) C.I.cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23kg and weight of frame 15 kg), R.C.C top slab with 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 455x610 mm and 45 cm deep for single pipe line:With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

50.17.1.1 : Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

od167807/2022_2023 : Providing and fixing white vitreous china wall hung wash basin of approved make including one CP brass pillar cock with water conservation mechanism including connecting pipes with all fittings 32 mm dia rubber plugs 32 mm dia CP brass waste coupling ,complete including CI/MS brackets duly painted, nuts, washers, etc. complete,cost and conveyance of all materials labour charges ,lead, lift necessary wall cutting / chasing and making good the walls,floors,slab,testing and commissioning to the satisfaction of Engineer in charge at all levels. The flow-rates of pillar tap shall be 4 LPM or as per GRIHA water conservation requirement .

od167810/2022_2023 : Providing and fixing coloured vitreous china under counter round wash basin 440 mm dia or nearest size of approved make including one CP brass pillar cock 15 mm NB including connecting pipes with all fittings 32 mm dia rubber plugs 32 mm dia CP brass waste coupling, 32 mm dia CP brass bottle trap, 15mm angle valve, etc. complete as directed by the Engineer-in-charge.

od167811/2022_2023 : Solar Circulation Pump with Controller Standard solar circulation pump (1 working) with digital, differntial temperature and programable auto solar controler (Make:Xylem) (Flow rate: 1050 LPH @ 1.5 bar)

od167812/2022_2023 : Supplying, fixing and testing salt glazed stoneware gully trap with rebated top square bodies 150mm x 150mm, CI grating 100mm dia outlet set in 75mm thick PCC 1:4:8 bed, 230mm thick masonry chamber in CM 1:3, internal and external plastering 12mm thick in CM 1:6 and 1:3 respectively, supply and fixing 450mm x 450mm size CI frame and cover, jointing to drain in CM 1:1, excavating, and cover, jointing to drain in CM 1:1, excavating, refilling and ramming etc., complete.

od167813/2022_2023 : Construction of valve chamber with 230 mm best quality TM bricks in CM 1:4 over a bed of 100mm thick PCC 1:4:8, internal walls plastered smooth in CM 1:3 and external walls plastered rough with sponge finish including curing with all necessary leads and lift and providing heavy duty cast iron cover with frame with locking arrangements etc., complete including Heavy duty cast iron cover of size 600 x600 (weight 115Kgs.) Size of chambers for valves up to 150 mm dia Size 0.6m x 0.6m x 1M (clear dimension) including approved make cast brass body water meter with necessary unions for fixing on the inlet main as shown on the drawing, etc., complete with (of approved makes - analog type). 100mm nominal dia

od167814/2022_2023 : Hot Water Recirculation Pump: Hot water recirculation pump on the building return pump (1 working+1 stand-by) -capacity: 3000 LPH @ 30 Mtrs

od167815/2022_2023 : Heat Pump Recirculation Pump: Circulation pump between heat pump and Storage tank Flow Rate: 5900 LPH @ 25 Mtrs)

od167816/2022_2023 : Supplying approved make PVC gully trap of size 160 x 110mm and CI grating 150mmx150mm size and light duty C.I cover with frames 300mmx300mm size(inside) the weight of cover to be not less than4.5kg and frame to be not less than2.7kg (CI MH cover and frame as per IS:1726) single sealed of size conveying to size the above mentioned items and constructing 30cmx30cm internal size gully trap chamber and depth upto 60cm,115 thk brick wall in CM 1:6 on a foundation of PCC 1:4:8.100mm thick plastering inside with CM 1:3,12mm thk with a neat cement flushing coat and conveying to site,cleaning ,installing and testing approved make PVC gully trap with 160mm outlet(Fabricated),surrounding with CC 1:1.5:3, 150x150mmm,top with CI grating above the PVC gulley trap and light duty CI cover and frame over the chamber including cost of all materials, etc complete as per approved drawing and as directed by Engineer-in- Charge.

od167819/2022_2023 : Heat Pump Air-water medium temperature heat pump with output of 24 kW 6 input of KW / 3 Phase at ambient temperature of 20 Degree Celsius with Copeland/Invotech Scroll compressor, R407C / R410A refrigerant with hot water output of 55Deg Cent-(1W + 1S)

od167820/2022_2023 : Supplying, installing and testing approved make GM ball valves PN-16 conforming to IS 1703 with unions etc., complete. 50 mm dia (Screwed ends)

od167821/2022_2023 : Timer Temperature based control panel

od167822/2022_2023 : Supplying and fixing in position approved make GM non-return valve conforming to IS 778 with unions etc., complete. 50mm dia

od167823/2022_2023 : Plumbing, Installation Commissioning Cost for Plumbing, installation and commissioning. Frames for collectors, Plumbing between Storage tank and Solar collector will be done in MS/GI duly insulated with Nitrile Rubber, between heat pumps and storage tanks in CPVC complete with accessories, fittings, safety devises, testing and commissioning of the system. and Electrical Supply, installation and commissioning of all electrical works comprising Internal cabling between the heat pump, solar controller, sensor cabling for heat pump, solar returnline pumps.

od167824/2022_2023 : Supplying and fixing in position approved make GM non-return valve conforming to IS 778 with unions etc., complete. 80 mm dia

od167825/2022_2023 : Supplying, Installing, testing and commissioning of Terrace booster hydro pneumatic system with Multiple variable frequency drive. The system shall comprises of pump, pre charged pressure tank, pressure switch etc., complete with electric motor at 2900 RPM 415V 3Ph 50 Hz required duty conditions mounted on common base plate and wiring from panel to the motor including air volume controls, etc., complete. Make: Grundfos/ Lubi/ Shakti Approved Equivalent Domestic Water Distribution: Flow Rate : 2.0 Lps (each pump 1.0 lps) with 2 pump system Cut in pressure : 7.5 Kg/Sqm Cut off pressure : 8.5 Kg/Scqm

od167828/2022_2023 : Supplying, Installing, testing and commissioning storm water disposal submersible pump with IP - 68 enclosure, of adequate HP, capable of giving a required discharge at suitable head to work on 3Ph 50Hz, 400/440V with necessary unions, flanges, Auto level controllers etc., complete. Make: Grundfos/ Lubi/ Shakti Approved Equivalent. a) 2.80 Lps at 15M head.(Basement waste water sump pump) (1 no. working + 1 no. standby = 1 Set)

od167829/2022_2023 : Supplying, Installing, testing and commissioning storm water disposal submersible pump with IP - 68 enclosure, of adequate HP, capable of giving a required discharge at suitable head to work on 3Ph 50Hz, 400/440V with necessary unions, flanges, Auto level controllers etc., complete. Make: Grundfos/ Lubi/ Shakti Approved Equivalent. b) 1.0 Lps at 30 M head. 1 no. working + 1 no standby

od167830/2022_2023 : Supply,Installation, Testing and Commissioning CI Butterfly Valves ( PN 16) slim seal standared lever operated type confirming to BS: 5155 with SS shaft disc, flanges, nuts, bolts etc. complete . 200 mm dia

od167831/2022_2023 : Providing, installing, testing and commissioning of approved make Water level Control instrument.

od167832/2022_2023 : Providing, installing, testing and commissioning of approved make Conductive type level sensor with SS 316 probes MS 2-1/2&quot; table E std flange and weather proof cast aluminium enclosure to sense two levels of the under ground sump and the over head water storage tank.

od167833/2022_2023 : Supply, Installation, Testing and Commissioning CI Butterfly Valves ( PN 16) slim seal standard lever operated type confirming to BS: 5155 with SS shaft disc, flanges, nuts, bolts etc. complete:65 mm dia

od167834/2022_2023 : Supply and wiring of Speaker Circuit - 2core 24/0.2mm ATC twin twisted shielded, FRLS type, armoured cable (Green colour) to be drawn in existing surface/recessed steel/PVC conduit as required

od167835/2022_2023 : Providing and fixing white vitreous china flat back urinal with sensor and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: complete as directed by the Engineer in charge at all levels.The flow-rates of urinal shall be 1.5-2 LPF or as per GRIHA water conservation requirement .

od167837/2022_2023 : Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.The faucet shall meet the flow regulation as per GRIHA requirement 4 lpm specified as per tender conditions.

od167839/2022_2023 : Supply,Installation, Testing and Commissioning CI Butterfly Valves ( PN 16) slim seal standared lever operated type confirming to BS: 5155 with SS shaft disc, flanges, nuts, bolts etc. complete: 150 mm dia

od167841/2022_2023 : Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern C.P. flush bend with fittings C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid. The water closet shall be 4/2 LPF flush and all fittings shall meet GRIHA water conservation requirement as per tender conditions.

od167842/2022_2023 : Supply,Installation, Testing and Commissioning of brass body Air Release Valve 25 mm dia type of approved make.

od167846/2022_2023 : Supplying, installing ,testing and commissioning of Pressure gauges for the respective floors near to the flow switches with Ball valves, siphon, Fittings like unions / colors / reducers etc. Glycerine filled pressure gauges to use on pump discharge lines. with 0 to 200PSI, 25 mm dia. Dial should be 150 mm dia.

od167849/2022_2023 : Supplying and fixing of CI double flanged wall casting pipe with puddle, 0.6m length including cost and conveyance of all materials,labour charges,making good the walls etc complete as directed by the Engineer in Charge. 65mm

od167851/2022_2023 : Supplying and fixing of CI single flanged wall casting pipe with puddle, 0.6m length including cost and conveyance of all materials,labour charges,making good the walls etc complete as directed by the Engineer in Charge. 65mm

od167852/2022_2023 : Supplying and fixing of CI single flanged wall casting pipe with puddle, 0.6m length including cost and conveyance of all materials,labour charges,making good the walls etc complete as directed by the Engineer in Charge. 80mm

od167855/2022_2023 : Supplying and fixing of CI double flanged wall casting pipe with puddle, 0.6m length including cost and conveyance of all materials,labour charges,making good the walls etc complete as directed by the Engineer in Charge. 80mm

od167856/2022_2023 : Supplying and fixing of CI double flanged wall casting pipe with puddle, 0.6m length including cost and conveyance of all materials,labour charges,making good the walls etc complete as directed by the Engineer in Charge. 100mm

od167859/2022_2023 : Supplying and fixing of CI single flanged wall casting pipe with puddle, 0.6m length including cost and conveyance of all materials,labour charges,making good the walls etc complete as directed by the Engineer in Charge. 100mm

od167860/2022_2023 : Supplying and fixing of CI double flanged wall casting pipe with puddle, 0.6m length including cost and conveyance of all materials,labour charges,making good the walls etc complete as directed by the Engineer in Charge. 150mm

od167862/2022_2023 : Supplying and fixing of CI single flanged wall casting pipe with puddle, 0.6m length including cost and conveyance of all materials,labour charges,making good the walls etc complete as directed by the Engineer in Charge. 150mm

od167863/2022_2023 : Providing and fixing sanitary fixtures for handicapped toilet including one wash basin , one number pillar cock with aerator all other related fittings like CP brass bottle trap,CP brass angle valve, CP brass waste coupling, etc, one number EWC Cistern complete with fittings seat cover, one no. hinged rail 4 nos. of grab rails 60cm etc, designed for people with special needs comes with as per manufacturers specification including cutting and making good the walls and floors wherever required as directed by Engineer-in-Charge. For griha water conservation mechansim following flow-rates shall be adopted for fixtures.Water Closet (Full flush/ Half flush) = 4 / 2 LPF,Lavatory Faucet = 4 LPM or as per GRIHA water conservation requirement .

od167865/2022_2023 : Providing and fixing C.P. brass long body bib cock with griha water conservation mechansim of approved quality conforming to IS standards and weighing not less than 690 gms. The flow-rates of bib cock shall be 4 LPM or as per GRIHA water conservation requirement .

od167868/2022_2023 : Providing and fixing premium quality C.P. brass wall shower mixer with griha water conservationmechanism along with overhead shower and shower arm with wall flanges of approved make andmodel including cost of all materials, labour etc., complete as directed by the Engineer-in-Charge atall levels. The flow-rates of Shower Head shall be 6-8 LPM or as per GRIHA water conservation requirement .

od167874/2022_2023 : Providing, fixing, supply, Installation and commissioning of 3 bay (2100mm long) brush finish scrub station ( manual operated) made out of high grade SS 304 1.6mm thk etc complete with all accessories i.e.thermostation mixing valve bypass system etc.

od167876/2022_2023 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6 Kgf/cm2 - Internal work- Exposed on wall

od167877/2022_2023 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110mm dia 6 Kgf/cm2 - Internal work- Exposed on wall

od167878/2022_2023 : Providing and fixing floor trap of PVC,110 mm outer dia(multi trap) including CP cockroach free floor grating with cup etc including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer-in-Charge at all levels

od167879/2022_2023 : Providing and fixing stainless steel grating of approved quality and colour. Circular type 100 mm nominal dia

od206036/2022_2023 : Supplying, installing, testing and commissioning approved make Water Softener with necessary Accessories complete with Frontal piping, valves, suitable supports for mounting pressure gauges, orifice plates. The softener shall be made of MS vessel with necessary protective coating. The cost of Softener shall also include initial charge of Resin media to suit the requirement etc., complete as per standards. Max. working pressure = 3.5kg/sqcm. Max flow rate = 11.5 cum/hr,at 10 hrs cycle

od206037/2022_2023 : Supplying, installing, testing and commissioning inter unit .SH 80 piping with necessary flanges, bolts, nuts, neoprene gaskets, welding wherever necessary, with necessary control valves, non return valves etc. and with one coat of primer and two coats of approved enamel paint with IS recommended color etc., complete.

od206038/2022_2023 : Supplying, Installing, testing and commissioning approved make Raw water Pressure sand filter with necessary accessories complete with Frontal piping, valves, suitable supports for mounting pressure gauges, orifice plates. The filter shall be made of MS vessel with necessary protective coating. The cost of filter shall also include initial charge of under bed multi-grade filter media to suit the requirement etc., complete as per the standards. Max. working pressure = 3.5kg/sqcm. Max flow rate = 11.5 cum/hr, at 10 hrs cycle

od206039/2022_2023 : Supplying, installing, testing and commissioning approved make activated carbon filter in MS vessel construction with internals, electrical control system complete with Frontal piping, valves, suitable supports for mounting, pressure gauges, orifice plate etc.., complete as per the detailed specification for the efficient working of system. The maximum working Pressure shall be 3.5 Kg/Sqcm. Max flow rate =11.5 cum/hr,at 10 hrs cycle

WATER SUPPLY PIPING WORKS

18.7.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall20 mm nominal outer dia pipes

18.7.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall25 mm nominal outer dia pipes

18.7.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall32 mm nominal outer dia pipes

18.7.5 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall40 mm nominal outer dia pipes

18.7.6 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall50 mm nominal outer dia pipes

18.8.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal outer dia pipes

18.8.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal outer dia pipes

18.8.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.32 mm nominal outer dia pipes

18.9.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work20 mm nominal outer dia pipes

18.9.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work25 mm nominal outer dia pipes

18.9.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work32 mm nominal outer dia pipes

18.9.6 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work50 mm nominal outer dia pipes

18.9.8 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work75 mm nominal inner dia pipes

18.9.9 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work100 mm nominal inner dia pipes

18.9.10 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work150 mm nominal inner dia pipes

od167826/2022_2023 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot cold water supply, including all CPVC plain brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall 65 mm nominal outer dia pipes

50.18.7.2.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge 20 mm dia 10 Kgf/cm2- Internal work - Exposed on wall

50.18.7.3.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 10Kgf/ cm2- Internal work- Exposed on wall

50.18.7.4.2 : Providing and fixing PVC, pipes fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 6 Kgf/cm2 - internal work- Exposed on wall

50.18.7.5.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 40 mm dia 6Kgf/cm2 - Internal work - Exposed on wall

50.18.7.6.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 10 Kfg/cm - Internal work- Exposed on wall

50.18.7.6.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6 Kgf/cm2 - Internal work- Exposed on wall

50.18.8.2.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 20 mm pipe 10 Kgf/ cm2

50.18.8.3.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 10kgf /cm2

50.18.8.4.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 32 mm pipe 6Kgf/cm2

50.18.8.6.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2

50.18.8.7.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc 63 mm pipe 4 kgf/ cm2

50.18.8.8.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2

50.18.8.9.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

50.18.8.9.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC Solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 110 mm pipe 4 kgf/cm2

50.18.9.3.2 : Providing and fixing PVC pipes includes jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 25 mm dia 10KGF/cm2

50.18.9.6.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm dia 10Kgf/cm2

50.18.9.6.2 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm dia 6 Kgf/cm2

50.18.9.7.1 : Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge. 63 mm dia 6Kgf/cm2

50.18.9.8.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 6 Kgf/ cm2

50.18.9.8.2 : Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching and refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 4 Kgf/cm2

50.18.9.9.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

50.18.9.9.2 : Providing and fixing PVC pipes includes joints of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in CHarge. 110 mm dia 4 Kg/cm2

50.18.9.10.1 : Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

50.18.9.16.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 10Kgf/cm2 - External work - Exposed on wall

50.18.9.16.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6Kgf/cm2 - External work - Exposed on wall

50.18.9.17.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clip at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 63 mm dia 6 Kgf/cm2 - External work - Exposed on wall

50.18.9.17.2 : Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 63 mm dia 4 Kgf/cm2- External work - exposed on wall

50.18.9.18.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall

50.18.9.19.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

50.18.9.19.2 : Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 m dia 4 Kgf/cm2 - External work - Exposed on wall

50.18.9.20.1 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Elbow

50.18.9.20.2 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63 dia 45 degree Elbow

50.18.9.20.3 : Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Door Elbow

50.18.9.20.4 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Bend

50.18.9.20.5 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes including jointing with PVC solvent cement - 63x63x63 mm dia Tee

50.18.9.20.6 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63x63x63 mm dia Door Tee

50.18.9.20.7 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia vent cowl

50.18.9.20.8 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia End cap

50.18.9.20.9 : Providing and fixing PVC moulded fitting / accessories for Rigid PVC pipes, including jointing with PVC solvent cement-63 mm dia Socket /coupling

50.18.9.20.10 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63x50 mm dia Reducer

50.18.9.21 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Elbow

50.18.9.21.2 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia 45 degree Elbow

50.18.9.21.3 : Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia Door Elbow

50.18.9.21.4 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Bend

50.18.9.21.5 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x75x75 mm dia Tee

50.18.9.21.6 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75x75x75 mm dia Door Tee

50.18.9.21.7 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Vent cowl

50.18.9.21.8 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia End cap

50.18.9.21.9 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Socket /coupling

50.18.9.21.10 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x63 mm dia Reducer

50.18.9.22.1 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

50.18.9.22.2 : Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow

50.18.9.22.3 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement-110 mm dia Door Elbow

50.18.9.22.4 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

50.18.9.22.5 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee

50.18.9.22.6 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x110 mm dia Door tee

50.18.9.22.7 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x75 mm dia Door Tee

50.18.9.22.8 : Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl

50.18.9.22.9 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia offset

50.18.9.22.10 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia End Cap

50.18.9.22.11 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling

50.18.9.22.12 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer

50.18.78 : Making chases up to 12.5x12.5 cm in walls including making good and finishing with matching surface after housing pipe etc.

od167993/2022_2023 : Supplying and fixing 32 mm dia GI pipe for gas out let connections including control valves, all plumbing works etc

od167994/2022_2023 : Supplying and fixing 250 mm dia PVC pipe from Inscpection chamber to Fermetation Tank gas out let connections including control valves, all plumbing works etc

BORE WELL WORKS

23.1.1.1 : Boring / drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS: 2800 ( part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools plants & machineries required for the job, all complete as per direction of Engineer - in- Charge, upto 90 metre depth below ground level.All types of soil300 mm dia

23.2.1.1 : Boring /drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS: 2800 ( part I), including collecting samples from different strata, preparing and submitting strata chart/ bore, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer- in- charge, beyond 90 metre & upto 150 metre depth below ground level.All types of soil300 mm dia

23.3.2 : Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS : 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer- in- Charge.150 mm nominal size dia

23.5 : Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer -in- charges

23.6 : Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit,over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer -in-Charge

23.7 : Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge.

23.8 : Gravel packing in tube well construction in accordance with IS: 4097, including providing gravel fine /medium/coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer- in- charge.

23.12 : Development of tube well in accordance with IS: 2800 (Part I) and IS : 1189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc.by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tube well, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer - in-charge.

23.13.2 : Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:150 mm dia

23.14.2 : Providing and fixing M.S. clamp of required dia to the top of casing / housing pipe of tubewell as per IS : 2800 ( part I), including ecessary bolts & nuts of required size complete.150 mm clamp

23.15.2 : Providing and fixing Bail plug / Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS : 2800 (part I).150 mm dia

MISCELLANEOUS WORK

od169746/2022_2023 : Providing and applying Antitermite treatment by injecting chemical emulsion Imidacloprid emulsiable concentrate .075% for pre-constructional treatment and creating a chemical barrier as per IS 6313 Part II 2001 for wall trenches, foundation, top surface of plinth filling, foundation of wall and floor, along the external perimeter of the building, etc. complete conforming to manufacturers specification and as directed by the Engineer in Charge. Plinth area only to be measured for the payment .The contractor should give guarantee for 10 years for the work .

od100938/2023_2024 : Design Supply Installation Testing and Commissioning of 90 KLD Sewage Treatment Plant Based on MBR Technology including all the mechanical and electrical equipment&apos;s like approved pumps, MBR membranes, filters, dosing system etc complete for the full function of Sewage Treatment Plant. The civil foundations and RCC tank structures / pump rooms shall not be included in this item and shall be paid separately. Design of the MBR system shall be done as per site conditions and got approval from the engineer in charge before procurement. Work shall be done as per manufacturer recommendation, technical specification and as directed by engineer in charge -90 KLD STP.

od167995/2022_2023 : Supplying and fixing 24 cft biogas burner including all connections, control valves all plumbing works etc

od167996/2022_2023 : Supplying and filling cow-dung with equal quantity of water for bacteria formation

od168005/2022_2023 :Design , Supplying,Installing, testing and commissioning approved make Incinerator with necessary accessories complete as per the standards. Waste Type: Organic, Capacity: 40 kg/batch Burning Ability: 50kg/time

od168014/2022_2023 :Water Purifier: Supplying,Installing, testing and commissioning approved make Raw water Pressure sand filter with necessary accessories complete with Frontal piping,valves,suitable supports for mounting pressure guages,orifice plates.The filter shall be made of MS vessel with necessary protective coating.The cost of filter shall also include initial charge of under bed multi-grade filter media to suit the requirement etc.,complete as per the standards. Max. working pressure = 10kg/sqcm. Max flow rate = 6m3/hr/m2 800 dia filter,at 10 hrs cycle

15.3 : Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

SIGNAGE & WAY FINDINGS

od114030/2022_2023 : Design, Supply and installation of Aluminium profile sliding door signage with the following specifications. The signage shall have an aluminium profile modular frame of height 100mm. The letters shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on 3mm thick foam board/ ACP Board fixed with adequate fasteners. The signage shall be in such a way that the foam board/ACP Board is slide to the aluminium profile for easy replacement of names : size-300mmx100mm

od114031/2022_2023 : Design, Supply and installation of vinyl signage on ACP with the following specifications. The signages shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on 3mm thick foam board and installed on 3mm thick ACP backing using VHB tapes.ACP backing surrounded by 50mm dia 1mm thick ss plated tube along the perimeter supported by 2 nos of 50mm dia 2mm thick ss plated pole permanently fixed at ground by concrete or can be fixed on wall support as per directions by engineer in charge.- ACP board size (2400x1200) bottom fixed at 60cm from ground as per the directions of engineer in charge.

od114032/2022_2023 : Design, Supply and installation of vinyl signage on ACP with the following specifications. The signages shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on 3mm thick foam board and installed on 3mm thick ACP backing using VHB tapes.ACP board size (2400x1200) bottom fixed at 60cm from ground as per the directions of engineer in charge.

od114033/2022_2023 : Design, Supply and installation of Reception/helpdesk signages as per following specifications. The signages shall be plotter cut 2 mil pigmented translucent vinyl pasted on3mm thick ACP/ 6mm thick hybrid board or 8mm Thick Acrylic glass on single side of approved make and colour of height 150mm. The signage shall be ceiling suspended using Stainless Steel strings as per the directions of engineer in charge, TEXT (MAY I HELP YOU, CASH, RECEPTION , REGISTRATION, INSURANCE..etc..)

od114034/2022_2023 : Supply and installation of way finding signages as per following specifications. The signages shall be plotter cut 2 mil pigmented translucent vinyl pasted on 3mm thick ACP/ 6mm thick hybrid board on both sides of approved make and colour.The signage shall be ceiling suspended using Stainless Steel strings as per the directions of engineer in charge. Way Finding Signage: 1200mmx600mm

od114035/2022_2023 : Design,Supply and installation of circular door signage for number with the following specification. The signages shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on 3mm thick foam board and installed on doors using VHB tapes : size of signage- 100mm dia

od114036/2022_2023 : Supply and installation of door signage with the following specification. The signages shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on 3mm thick sunboard and installed on doors using VHB tapes: Door Signage: 300mmx100mm

od114037/2022_2023 : Supply and installation of signage board with the following specification. The signages shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on 3mm thick sunboard and installed above doors using VHB tapes : Signage size: 1200mmx150mm

od114038/2022_2023 : Design,Supply and installation of Vinyl printed signage for awareness and guidelines for hospital departments as specified by the client with the following specification. The signages shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on 3mm thick foam board and installed on wall/glass using VHB tapes.Room vinyl printed sticker with 3mm foam board backing as per the directions of engineer in charge.

od114039/2022_2023 : Supply and installation of 3 mm Acrylic box letters with 70 mm projection, vinyl pasted on first face with 3 module LEDs, SMPS and other electrical fittings fixing on ACP/wall base as per the directions of client/engineer in charge.

od114040/2022_2023 : Supply and installation of frosted film pattern throughout all the internal glass panels wherever required of upto 1.5 m height as per the approved pattern as per the direction of Engineer in charge.

od114041/2022_2023 : Design,Supply and installation of Vinyl printed self adhesive sticker signage on glass for awareness and guidelines. with the following specification. The signages shall be plotter cut 2 mil pigmented translucent vinyl of approved design pasted on glass.

od114042/2022_2023 : Providing and fixing of 3mm thick ACP/ 6mm thick hybrid board or 8mm Thick Acrylic glass backing for singnage. Shall be fixed by means of ss studds or screwed as per directions of engineer in charge the price shall be inclusive of all hardwares and accesories used for fixing as per the directions of engineer in charge.

od114043/2022_2023 : Supply and installation of 8mm thick Glass marker board with led lights (900X900)mm on wall as per directions by engineer in charge.

od114044/2022_2023 : Supply and installation of Laminated fire evacuation plan colour print as per NBC 2016,IS 1644-1988 standard, installed on doors /walls using VHB tapes. as per directions by engineer in charge.

od114045/2022_2023 : Supply and installation of FIRE EXIT SIGNAGE ,size: 12 inch x 6 inch ,Color: green ,Film Type Photoluminescent. The signage shall be ceiling suspended using Stainless Steel strings as per NBC 2016 standards the directions of engineer.

od114046/2022_2023 : Design, Supply and installation of SS signage on ACP with the following specifications. The letters shall be made out of 40mm projected ss plated box signage with 3mm ACP/ Aluminium sheet backing supported by 2 nos of 75mm dia 2mm thick GI painted pole permanently fixed at ground by concrete - ACP board ( Text - Government Taluk Hospital Varkala, or as per directions of engineer in charge.

Description of Work / Item(s)

Amount

ELCTRICAL

od94656/2022_2023 :HT INSTALLATION Supply,Instalation,testing and commisioning of 120AH, 24V station type, sealed maintenance free lead acid a batteries complete with battery stand, full wave bridge SCR battery charger (trickle / boost) inclusive of control panel.

od94657/2022_2023 : Load Break Panel (OUTDOOR METERING PANEL) Supply installation testing and commissioning of 11kV,Load break panel with outdoor, wheatherproof, metering cubicle fabricated out of 14 SWG CRCA sheet, powder coated after seven tank process, provision for connecting 3x300sqmm cable at both ends, 3nos 25/5A, Cl-0.2s, 10VA CT, 11kV/110V, Cl-0.2, 25VA PT, fixing of already tested TOD meter fixed in pilfer-proof outdoor meter box suitable for housing the meter and test terminal block (TTB), all complying with relevant standards and as per the requirements of KSEBL including excavation, backfilling RCC foundation

od94658/2022_2023 :Supply, installation and testing of TOD meter for KSEBL (0.2S accuracy class, 3ph 4 wire, DLMS compatible) test terminals etc. all prewired, tested in the TMR section of KSEBL and as per recommendations and fixing in the metering panel complete as required.

od164634/2022_2023 : SITC of 11kV, 630A, SCADA compatible, SF6 insulated, 3 way RMU with 3 numbers load break switches as per KSEB specification including foundation with all accessories like FPI,VPIS, battery battery charger, CT& terminal protector etc complete

od94660/2022_2023 : Supply, testing and commissioning of the following PVC Insulated Armoured Aluminium Cables (AYWY/AYFY) /XLPE (A2XCEFY) to be laid in HT trenches, cable trays, hume pipes, including supply and fixing of painted MS clamps, spacing of the clamps not exceeding 60cms, nuts and bolts, screws, identification tags, route markers etc. required for clamping intervals as necessary 3.0C x 300 SQ.MM.XLPE

od105773/2022_2023 : Supply, testing and commissioning of the following PVC Insulated Armoured Aluminium Cables (AYWY/AYFY) /XLPE (A2XCEFY) 3.0C x 150 SQ.MM.XLPE

8.2.2 : Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etcAbove 120 sq. mm and upto 400 sq. mm

8.3.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 120 sq. mm and upto 400 sq. mm

8.4.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required.Above 120 sq. mm and upto 400 sq. mm

10.4.3 : Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:150 sq. mm

10.4.4 : Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:300 sq. mm

10.5.4 : Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :300 sq. mm

od104004/2022_2023 : UNITISED SUB STATION - INDOOR - WITH VCB PANEL - 11KV - 400KVA. Indoor Unitised Substation (USS) with the following: Incomer: 11kV, 630A, 350MVA, VCB with earth switch, 24V dc shunt trip coil, battery, battery charger, overcurrent and earth fault relay, protection CT, 40-20/5A, Cl 5P10 CT, 3O/C and 1EF Protection static relays with high set element, cable box suitable for 3x300sqmm 11kVcable and emergency OFF push button, etc complete - 1No. Transformer: 400kVA, 11kV/433V, 50Hz, 3phase, Cu-wound AN cooled, Vector DYN-11, cast resin, indoor, dry-type transformer with off-load tap changer, winding temperature alarm and trip, HV terminals suitable for interconnecting with VCB and LV terminals suitable for connecting cable of 2 run 3.5x 400 sqmm cable - 1No Suitable base plate for mounting of the equipment, bus bar inter connections, operating handle mechanism, spring charging mechanism and enclosure for the USS

od94662/2022_2023 : DIESEL GENERARTOR SET Supply of 3phase., 200kVA 433V, 0.8pf. 50Hz, 1500rpm DG Prime Rated Diesel Generator Sets as detailed below and as shown on drawings. Water cooled diesel generating set comprising of diesel engine, alternator, fuel tank, starting system, battery, electronic governor, etc. with all accessories as required. The generator set shall have an integral type acoustic enclosure as per latest CPCB norms. Smoke exhaust emission from diesel engine shall comply with the latest emission standards. Generator set shall be inclusive of fly wheel, flexible coupling, air cleaner, corrossion resistor, fan with guard, fuel pump, fuel filter, electrical starting system with starter, 24V battery with regulator, instrument panel, RPM indicator, residential silencer, etc. The control panel shall be floor mounted dust and vermin proof with 315A, 4Pole, 35kA, MCCB (microprocessor based) complete with all necessary relays, CTs, control wiring, etc. as necessary for interconnection with PLC. Scope shall include first filling of oil and diesel for commissioning of the DG set.

od94663/2022_2023 : DIESEL GENERARTOR SET Installation testing and commissioning of 3phase.200kVA 433V, 0.8pf. 50Hz, 1500rpm DG Prime Rated Diesel Generator Sets (Installation only)

od94664/2022_2023 : Providing, fixing of exhaust pipe line of 200/150mm dia B class MS pipe with accessories like flange, supports, through wall, including providing thermal insulation heat resistance painting etc compleete

od94665/2022_2023 : Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermine proof, LT panel board. The panel shall be complete with all necessary switch gear, control gear, control wiring, metering, all protective relays and instrumentation system suggested by Electrical inspectorate, etc. as required and as listed below in brief and details in technical data sheets and technical specifications. All necessary components, accessories and wiring shall be provided for auto and manual load management of incomer, bus coupler , circuit breakers by PLC. Incomer: 1. 630A, 50kA, 4P, MCCB+630A,4P contactor - 1Nos. + 315A, 50kA, 4P, MCCB + 315 A contactor - 2Nos. Bus Bar: Al busbar sized suitably for 630A TPN and 25x6 Cu Earth, BUS Coupler-630A, 50kA, 4P, MCCB + 630A contactor- 1No. Outgoing: 1. 250A, 25kA, TP + NL-MCCB -2Nos., 200A, 25kA, TP+NL MCCB- 2Nos,160A, 25kA, TP MCCB + NL- 6Nos,125A, 25kA, TP MCCB + NL - 2Nos,160 A TPN Isolator -1 No.

od94667/2022_2023 :150KVAR APFC PANEL:- SITC of Automatic Power Factor Correction Panel made of 16SWG thick CRCA sheet fully compartmentalized, duly rust inhibited, degreased, zinc phosphate and powder coating painted with approved colour and quality, complete with hinged and earthed front doors, name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made of 3mm thick sheet steel boards with 500V, APPH, Heavy Duty Capacitor and 7% detuned reactors, Capacitor Duty contactor and microprocessor based APFC Relay in steps of 12 with all required accessories. Incomer : 250A 4P Isolator - 1 No uP based APFC Relay (12 Steps) - 1No, 250/5A, CL- 1, CT, 10VA - 1Set, Multi-function digital meter - 1Sets, RYB Indication Lamp - 1Set Busbars: 250A Al for Phase 200A AL for Neutral, 25X3 mm cu for Earth. Outgoings: 125A, SFU with Fuse link- 1 set, 100A, SFU with link - 1set., 63A, SFU with fuse -7set, . 100A, 3P, Contactor - 1Nos. 63A, 3P, Contactor - 7Nos, 50kVAr APPH, 500V with 7% detuned reactor - 1Sets,25kVAr APPH, 500V with 7% detuned reactor - 1Sets, 20kVAr APPH, 500V with 7% detuned reactor - 2 sets, 10kVAr APPH, 500V with 7% detuned reactor -3Set, 5 kVAr APPH, 500V with 7% detuned reactor - 1Set (one number 20kVAR as fixed capacitor)

od94668/2022_2023 : UTILITY PANEL-SMDB SITC of Sub Main Distribution Panel Board with Isolator / MCCB incomer and MCCB outgoing. TPN switch gear shall be supplied with equally rated neutral link and all MCCBs shall be with rotary handle.Incomer : 200A,TPN Isolator with indication lamp- 1Nos Busbars: Phase &amp; N 200A AL for Neutral, 25X3 mm cu for Earth Outgoings: 100A 20kA, TP, MCCB + NL - 1Nos, 63A 20kA, TP, MCCB + NL - 7Nos, 40A 20kA, TP, MCCB + NL - 4Nos

od94669/2022_2023 : AC-SMSB SITC of Sub Main Distribution Panel Board with Isolator / MCCB incomer and MCCB outgoing. TPN switch gear shall be supplied with equally rated neutral link and all MCCBs shall be with rotary handle. Incomer : 160A,TPN Isolator with indication lamp- 1Nos Busbars: 160 A Al for Phase 100A AL for Neutral, 25X3 mm cu for Earth Outgoings: 63A TP, MCB + NL - 4Nos, 40A, TP, MCB + NL - 4Nos

od94670/2022_2023 : LIGHTING / RP SMSB-1 (SMDB-1) SITC of Sub Main Distribution Panel Board with Isolator / MCCB incomer and MCCB outgoing. TPN switch gear shall be supplied with equally rated neutral link and all MCCBs shall be with rotary handle.Incomer : 250A,TPN Isolator with indication lamp- 1Nos. Busbars: 250A Al for Phase 250A AL for Neutral, 25X3 mm cu for Earth Outgoings: 125A, 25kA, TP, MCCB + NL - 12Nos

od94671/2022_2023 : SUB MAIN DISTRIBUTION BOARD (SMDB-A-xF) SITC of Sub Main Distribution Panel Board with Isolator / MCCB incomer and MCCB outgoing. TPN switch gear shall be supplied with equally rated neutral link and all MCCBs shall be with rotary handle. Incomer : 200A,TPN Isolator with indication lamp- 1Nos Busbars: 200A Al for Phase 200A AL for Neutral, 25X3 mm cu for Earth Outgoings: 63A, 4P, D Curve, MCB - 8 Nos

od209999/2022_2023 : Supply installation testing and commissioning of LT wall/floor mounting panel board fabricated out of 16 swg CRCA sheet, powder coating with two coats of paint over zinc chromate metal primer including aluminium bus bar, supports, etc consisting of Incomer : One number 125A 4 pole isolator, bus bar 125A 4P aluminium bus bar ,out going: 4 numbers 63A, 4P,20kA MCCB.

od94672/2022_2023 : UPS Panel :SITC of Sub Main Distribution Panel Board with Isolator / MCCB incomer and MCCB outgoing. TPN switch gear shall be supplied with equally rated neutral link and all MCCBs shall be with rotary handle. Incomer : 200A,TPN Isolator with indication lamp- 1Nos Busbars: 200A Al for Phase 200A AL for Neutral, 25X3 mm cu for Earth Outgoings:100A, 20kA, TP, MCCB + NL - 6Nos, 63A TPN, MCB - 6Nos

od94673/2022_2023 : Supply installation testing and commissioning of three phase (input and output) 440V, 50Hz, 60kVA UPS with minimum 1 hour backup with SMF battery. The system shall be true online, double conversion technology IGBT-based invertor and rectifier with pf &gt;9.5, THD &lt;3%, provision for parallel redundancy and 100% generator compatabile. The system shall comply to IEC /EN 62040-1 and relevant IS standard. 60 (2x30) kVA modular UPS

od94674/2022_2023 : SUB MAIN DISTRIBUTION BOARD (SMDB-P-xF) SITC 8 way, vertical type TPN MCB of Distribution Board with 100 A,20 kA TP+NL MCCB incomer and 8 Nos 40/32 TP+NL MCB outgoing. TPN switch gear shall be supplied with equally rated neutral link and all MCCBs shall be with rotary handle

od94675/2022_2023 : LIFT PANELS; SITC of Sub Main Distribution Panel Board with Isolator / MCCB incomer and MCCB outgoing. TPN switch gear shall be supplied with equally rated neutral link and all MCCBs shall be with rotary handle.Incomer : 63A,TPN Isolator with indication lamp- 1Nos Busbars: 100A Al for Phase 100A AL for Neutral, 25X3 mm cu for Earth Outgoings: 32A, 4P, RCBO, 100mA - 1No, 25A, 2P, RCCB, 30mA - 1No, 10A, 1P, B Curve, MCB - 4Nos

2.3.7 : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator2 + 8 way, Double door

2.3.8 : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator2+12 way, Double door

2.4.1 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)4 way (4 + 12), Double door

2.4.2 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way (4 + 18), Double door

2.4.3 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way (4 + 24), Double door

2.5.1 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)4 way (4 + 12), Double door

2.5.2 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)8 way (4 + 24), Double door

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.3 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole

2.10.4 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

2.10.5 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and neutral

2.11 : Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

2.12.1 : Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.13.1 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.13.2 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.14.1 : Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

2.14.2 : Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.15.1 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

2.15.2 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.15.3 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

od94676/2022_2023 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, 100mA, RCBO, in the existing MCB DB complete with connections, testing and commissioning etc. as required.25A/32A/40A

2.24.1 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.For 4 way, Double door TPN MCBDB

2.24.2 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.For 6 way, Double door TPN MCBDB

2.24.3 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.For 8 way, Double door TPN MCBDB

od94677/2022_2023 : Supplying and fixing following way, Flexible type , sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper busbar, neutral bar(4 Nos), earth bar(4 Nos), din bar, interconnections, powder painted including earthing etc, as required (But without MCB/ RCBO/ RCCB/ Isolator) 2 Row 14 Module

2.25 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for tripple pole and neutral, sheet steel, Vertical MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.

2.17 : Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32amps 415 volts "C" curve TP MCB complete with connections, testing and commissioning etc. as required.

od165348/2022_2023 : Supply and fixing of 4 way MCB enclosure of size 150x300mm, fabricated out of 16swG CRCA sheet

od116858/2022_2023 : Supply installation testing and commissioning of Isolator in Sheet steel enclosure with provision for cable termination at both ends&lt;br&gt;63A, TPN Isolator

od116859/2022_2023 : Supply installation testing and commissioning of Isolator in Sheet steel enclosure with provision for cable termination at both ends&lt;br&gt;100A, TPN Isolator

od116860/2022_2023 : Supply installation testing and commissioning of Isolator in Sheet steel enclosure with provision for cable termination at both ends&lt;br&gt;125A, TPN Isolator

2.18 : Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth,metal enclosed plug top along with 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

2.20 : Supplying and fixing 30 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 amps "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

od94678/2022_2023 :Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, 100mA, RCBO, in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

od94679/2022_2023 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, 300/00mA, RCBO, in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

od94680/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x 3.5C x 400 Sq.mm.

od94681/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x 3.5C x 300 Sq.mm.

od94682/2022_2023 :Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x 3.5C x 240 Sq.mm.

od94683/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x 3.5C x 185 Sq.mm.

od94684/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x 3.5C x 150 Sq.mm.

od94685/2022_2023 :Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x 3.5C x 120 Sq.mm.

od94686/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x 3.5C x 95 Sq.mm.

od94687/2022_2023 :Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x 3.5C x 70 Sq.mm.

od94688/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x 3.5C x 50 Sq.mm.

od94689/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x 3.5C x 35 Sq.mm.

od94690/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x4C x 25 Sq.mm.

od94691/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x 4C x 16 Sq.mm.

od94692/2022_2023 :Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x 4C x 10 Sq.mm.

od94693/2022_2023 :Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x 4C x 6 Sq.mm.

od94694/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x 4C x 4 Sq.mm.

od94695/2022_2023 :Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1 x 4C x 2.5 Sq.mm.

od94696/2022_2023 : Supply, testing and commissioning of the following Aluminium LT Cables (A2XFY/AYFY) / (XLPE) 1Rx 3C x 2.5 Sq.mm.

90.12.6.3 : Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.2 core 10 sq mm

od94697/2022_2023 : Supply testing and commissioning of the single core FR PVC insulated flexible copper cables for working voltage upto and including 1100 V 6C x 1.5 Sq.mm

od94698/2022_2023 : Supply testing and commissioning of the single core FR PVC insulated flexible copper cables for working voltage upto and including 1100 V 12C x 1.5 Sq.mm

7.1.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Upto 35 sq. mm

7.1.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 35 sq. mm and upto 95 sq. mm

7.1.3 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 95 sq. mm and upto 185 sq. mm

7.1.4 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 185 sq. mm and upto 400 sq. mm

7.7.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.7.2 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

7.7.3 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

7.7.4 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

7.8.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.8.2 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

7.8.3 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

7.8.4 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

9.1.2 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 10 sq. mm (19mm)

9.1.32 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

9.1.20 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X25 sq.mm (28mm)

9.1.21 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 35 sq. mm (32mm)

9.1.22 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 50 sq. mm (35mm)

9.1.23 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.24 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 95 sq. mm (45mm)

9.1.25 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm)

9.1.26 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 150 sq. mm (50mm)

9.1.27 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)

9.1.29 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 240 sq. mm (62mm)

9.1.30 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 300 sq. mm (70mm)

9.1.31 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 400 sq. mm (82mm)

9.1.34 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm)

4.6.2 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.150 mm width X 50 mm depth X 1.6 mm thickness

4.6.3 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.225 mm width X 50 mm depth X 1.6 mm thickness

4.6.4 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.300 mm width X 50 mm depth X 1.6 mm thickness

4.6.6 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.450 mm width X 50 mm depth X 2.0 mm thickness

4.6.7 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.600 mm width X 50 mm depth X 2.0 mm thickness

14.13.2 : Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required80 mm dia

14.13.3 : Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required100 mm dia

14.13.4 : Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required150 mm dia

14.16.1 : Supplying and laying of following size DWC HOPE pipe lSI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 em below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required.63 mm dia (OD-63 mm & ID-51 mm nominal)

14.16.2 : Supplying and laying of following size DWC HOPE pipe lSI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 em below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required.90 mm dia (OD-90 mm & ID-76 mm nominal)

14.16.3 : 120 mm dia (OD-120 mm & ID-103 mm nominal)

1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

od94699/2022_2023 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm&lt;br&gt;FRLS PVC insulated copper conductor single core cable in surface / recessed&lt;br&gt;medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. above 8M long point

1.11 : Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

1.12 : Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

1.14.1 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.14.7 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

1.14.8 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 4 sq. mm + 2 X 4 sq. mm earth wire

1.14.9 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 6 sq. mm + 2 X 6 sq. mm earth wire

1.14.10 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 10 sq. mm + 2 X 6 sq. mm earth wire

1.14.11 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 16 sq. mm + 2 X 6 sq. mm earth wire

1.17.4 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.4 x 1.5 sq. mm

1.17.13 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.4 x 2.5 sq. mm

1.17.14 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.5 x 2.5 sq. mm

1.17.23 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.5 x 4 sq. mm

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

1.22.1 : Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.75 mm X 75 mm X 60 mm deep

1.22.3 : Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.150 mm X 75 mm X 60 mm deep

1.25 : Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.3 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.4 Module (125mmX75mm)

1.27.4 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

1.27.5 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

1.27.6 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.12 Module (200mmX150mm)

1.31 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

od181232/2022_2023 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 &amp; 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

90.9.1.1 : Supply and fixing 50 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.50x50mm Cable Management System with base and lid

90.9.2.1 : Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.100 x 50 mm CMS with base and lid

1.33 : Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

1.34 : Supplying and fixing brass batten/ angle holder including connection etc. as required.

1.38 : Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.3 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.24.7 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet

1.45 : Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

od61332/2022_2023 : Supplying and fixing extra down rod of 30 cm length MS pipe, 15 mm dia, heavy gauge including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

1.55.3 : Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

1.56 : Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlets and 2 Nos. 5/6 A modular switches, connection etc. as required. (For light plugs to be used in non residential buildings).

1.57 : Supplying & fixing suitable size Gl box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

5.2 : Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required

od94700/2022_2023 : Supply and installation charges for Providing 1200x 1200x12 mm Cast Iron plate earth station, conforming to IS 3043 filling with mixtures of salt, sand and charcoal, construction of earth chamber with brick masonry and covering with heavy duty Cast Iron Cover hinged to Cast Iron Frame, including excavation &amp; backfilling of earth pit.

5.4 : Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.10 : Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

5.11 : Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

od94703/2022_2023 : Providing and fixing 25mm x 3mm copper strip in ground /surface/ cable tray or in recess for connections etc as required.

5.17 : Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

od104937/2022_2023 : Supply and laying of 3.25mm(10swg) copper wire through tray/wall including termination at both ends

90.16.1.9 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required2.64 mm GI conductor (12 SWG)

90.12.10.4 : Supply & laying of DWC pipe in ordinary soil 0.75m below ground level including excavation77/63 mm or nearest size

90.12.10.7 : Supply & laying of DWC pipe in ordinary soil 0.75m below ground level including excavation120/102.5 mm or nearest size

90.16.3.7 : Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required ( for horizontal run)50 x 6 mm GI strip

90.16.3.5 : Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required ( for horizontal run)32 x 6 mm GI strip

90.16.3.6 : Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required ( for horizontal run)40 x 6 mm GI strip

90.16.4.8 : Supply and clamping the following sizes of strips on surface of wall / parapet/ existing cable tray using clamps fabricated from 20 x3 mm GI flat duly painted or heavy duty GI spacer saddles, spacing of clamps not exceeding 1 m , making good the damages, colour washing etc. as required ( for vertical run).25 x 3 mm copper strip

od181746/2022_2023 : Supply and laying of 20 x 6 mm Aluminum strip with epoxy busbar support for vertical and horizontal running of Lightning protection including all fixing material in complete.

5.18 : Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

6.2 : Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube,having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

6.7 : Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

6.8 : Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

6.14 : Providing and laying G.l. tape 32 mm X 6 mm from earth. electrode directly in ground as required.

od94704/2022_2023 : Supply and Installation of Energy efficient recessed mounted fully difused 26/28W LED light fittings suitable for 600x600mm grid-type suspended ceilings with all accessories ( Phillips make RC380B30S or eqvt)

od94705/2022_2023 :Supply and Installation of Energy efficient surface / recessed mounted square 18W LED light fittings of size 280x280mm grid-type suspended ceilings with all accessories ( Phillips make SM251C20S or eqvt)

od94706/2022_2023 :Supply and Installation of Low glare, high effeciency surface/ recess mounted 12W LED down light - circular profile

od94707/2022_2023 : Supply and Installation of 1.2m long ceiling surface / wall mounted 20W LED Batten light fitting

od94708/2022_2023 : Supply and Installation of 0.6m long ceiling surface / wall mounted 10W LED Batten light fitting

od181039/2022_2023 : Supply and Installation of Low glare, high efficiency surface/ recess mounted 6W LED down light - circular profile&lt;br&gt;

od94710/2022_2023 : Supply, Installation, Testing and Commissioning of 1200 MM sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) motor, class of insulation:B, 3 nos blades, 30 cm long down rod, 2 nos canopies, shackle kit, saftey rope, copper winding, power factor not less than 0.9, service value (CMM/W) minimum 6.85, Air delivery minimum 215 CM/M, 350 RPM, (tolerance as per IS:374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including saftey pin, nut, bolts, washers, temperature rise = 75 degree C (max), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

od94711/2022_2023 : 18W SOLAR POWER LED STREET LIGHT LAMP WITH POLE ; SITC of 18W LED, High Pressure Aluminium Die Cast,IP65 street light fittings with 75W solar PV module, charge controller, 48 WH, 12.8V, 600mAh Lithium iron battery, Three stage battery charge monitoring algorithm, Ideal current consumption Less than 2 mA, Galvanised iron pole of size 150mm at a height of 6m, bracket for light fittings, weather proof enclosure for battery, and charge controller, foundation using cement concreate1:3:6, using 20mm metal at a height of 1m, providing and fixing of foundation bolt, etc complete.

90.15.3.2 : Supply installation testing commissioning of Octogaonal Pole made of hot dip galvanised GI sheet 70mm top diameter, 130mm bottom diameter thickness 3mm base plate dimensions of 200x200x12mm suitable for wind speed as per IS 875 Part III double arm bracket 0.5mt including connector foundation bolt 4 nos fixed in existing RCC foundation and junctions box etc.complete 6 Meters

90.15.4.1 : Supply Conveyance, installation, testing and commissioning of 20W LED street light with bracket output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing,acrylic cover complete with THD Less than10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)

od94712/2022_2023 : Supply and fixing of weather proof, 3D signage board 1m height and 4 m wide fabricated with Angle iron structure and 14SWG CRCA sheet, fixing of 3D, letters made using 2mm thick acrylic sheet, each letter is illuminated with LED tube lights and sufficient LED rope including 12V dc power controller for each letter consist two layer LED as approved

od94713/2022_2023 : Supply conveyance, installation, testing and commissioning of infra red sensors with contacts suitable for occupancy and daylight controllers .

od94714/2022_2023 : Supply fabrication, painting with two coats of synthetic enamel paint over a coat of zinc chromate primer and erection of MS structural steel ( Angle iron/ flats/T section) for supporting the equipments, exhaust line etc complete

od94715/2022_2023 :Supply and installation of emergency OFF trip push button for emergency switch off for power supply with front Glass and painted in RED Colour.

od94716/2022_2023 : Supply of Insulated hand gloves IS 4770/1991

od94717/2022_2023 : Supply and laying of elastomer mat with ISI mark suitable for 11 KV,2.5mm THICK installation conforming to IS:15652:2006

14.10 : Providing and laying in position reinforced cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc. including form work etc. as required (excluding reinforcement).

od94718/2022_2023 : Supply of all equipments, design, installation,testing, commissioning and training of Smart energy measurment system, including accessories like, energy meters, water meters, transducers, indicators, ;controll cabling, communicable equipments etc for measuring various energy input sources(KSEB power, DG sets, solar power system, etc) and water input sources ( muncipal water, open well, tube well etc) for measuring input energy and water system processing the data with predefined parameters analysing the data , provide optimam output result for reducing the energy and water resources.All data cabling, input ouput devices, power supply module, DC source with battery, server, softwares, etc included in this system. It must have Service Oriented Architecture-based integration, Load management based on business rules, data management, outage management system, peak load management system, etc. Meter is to be SCADA, BMS and DMS compatible. Real Time data acquisitions and analysis, control of field electrical equipment, managing electricity flow and maintaining safety, load flow analysis, state estimation, demand forecast, Capable to manage large data, ensure data security and integrate with various sub-systems including legacy systems. automation solutions for accounting renewable energy into the grid, operational details of DG set etc.

CONDUITS AND SLEEVES 1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

1.21.4 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.40 mm

1.21.5 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.50 mm

od113713/2022_2023 : Supplying and laying of 32 MM coloured HDPE pipes ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, complete with fitting and cutting, jointing etc for laying optic fibre cable or multi pair telephone cables including excavation/chipping/ drilling and refilling/ covering etc complete as required.

od113715/2022_2023 : Supply and fixing of 25mm dia MS flexible pipe with pvc coating along with all ancillaries and accessories like coupler etc as required

4.6.2 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.150 mm width X 50 mm depth X 1.6 mm thickness

4.6.4 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.300 mm width X 50 mm depth X 1.6 mm thickness

4.6.10 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.450 mm width X 62.5 mm depth X 2.0 mm thicknessICDDescriptionUnit

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

od113745/2022_2023 : Supplying and fixing PVC boxes of sizes 200x100mm on surface with suitable size of sheet cover (white colour) in front etc required

NETWORKING od113698/2022_2023 : Supplying, drawing and testing of UTP 4 pair CAT 6 23 AWG LAN cable in the existing surface/recessed steel/PVC conduit as required 1 run of Cable

od113701/2022_2023 : Supplying drawing and testing of UTP 4 pair CAT 6 23 AWG LAN cable in the existing surface/recessed steel/PVC conduit as required 2 run of Cable

od113705/2022_2023 : Supplying, drawing and testing of UTP 4 pair CAT 6 23 AWG LAN cable in the existing surface/recessed steel/PVC conduit as required 3 run of Cable

od113711/2022_2023 : Supplying drawing and testing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required 4 run

od113731/2022_2023 : Supply and laying of 6 Core OS2 SM Central Loose Tube Armored Indoor / Outdoor Cable through the existing PVC conduit including splicing and termination at both ends etc. complete

1.28.1 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.1 or 2 Module

1.28.2 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module

od113736/2022_2023 : Supply, installation, testing and commissioning of I/O point with single RJ45 outlets, in existing back box including IDC crimping etc. complete (data/cctv)&lt;br&gt;

od113737/2022_2023 : Supply, installation, testing and commissioning of I/O point with dual RJ45 outlets, in existing back box including IDC crimping etc. complete (data/cctv) &lt;br&gt;

od113738/2022_2023 : Supply installation testing and commissioning of Patch cord - 2mtr

od113739/2022_2023 : Supply installation testing and commissioning of Patch cord - 1mtr

od113740/2022_2023 : Supply installation testing and commissioning of Pigtail SC SM simplex length 1 Metre

od113741/2022_2023 : Supply installation testing and commissioning of 19.;, 42U, 800X1000mm Depth Floor Mount Network Rack with Front Glass Door, Horizontal Cable Manager, Horizontal PDU, 12 round pin sockets - 2 No, Cooling Fan, Mounting Hardware Screws with all mechanical supports etc. complete

od113730/2022_2023 : Supply installation testing and commissioning of floor mount 22 U Network Rack 600 mm X 600 MM with cable manager, PDU 6 Socket, Cable Organizer 1U Closed, Fan &amp; Hardware Kit and all other accessories etc. complete

od113742/2022_2023 : Supply installation testing and commissioning of 19.;,9U, 600 MM Depth Wall Mount Rack with Front Glass Door, Horizontal Cable Manager, Horizontal PDU, 6X5Amps - 1 No, Cooling Fan with necessary Mounting Hardware Screws with all mechanical supports etc. complete

od113743/2022_2023 : Supply, Installation, Testing and Commissioning 28-Port Gigabit L2 Managed Switch with 24-Port PoE+ 384 W PoE Budget: 24&times; 802.3at/af-compliant PoE+ ports with a total power supply of 384 W*. Full Gigabit Ports: 24&times; gigabit PoE+ ports and 4&times; gigabit SFP Slots provide high-speed connections, Centralized Cloud Management, and Intelligent Monitoring.;Centralized Management: Cloud access for ultra convenience and easy management. Static Routing: Helps route internal traffic for more efficient use of network resources. Robust Security Strategies: IP?MAC-Port Binding, ACL, Port Security, DoS Defend, Storm control, DHCP Snooping, 802.1X, Radius Authentication, and more. Optimize Voice and Video Applications: L2/L3/L4 QoS and IGMP snooping. Standalone Management: Web, CLI (Console Port, Telnet, SSH), SNMP, RMON, and Dual Image bring powerful management capabilities.

od113744/2022_2023 : Supply, Installation, Testing and Commissioning of 24-Port Gigabit L2 Managed Switch with 4 SFP Slots Gigabit Ethernet connections on all ports provide full speed of data transferring L2+ feature Static Routing, helps route internal traffic for more efficient use of network resources IP-MAC-Port Binding, ACL, Port Security, DoS Defend, Storm control, DHCP Snooping, 802.1X Authentication and Radius provide you robust security strategies L2/L3/L4 QoS and IGMP snooping optimize voice and video application IPv6 support with dual IPv4/IPv6 stack, MLD snooping, IPv6 neighbor discovery Web, CLI (Console Port, Telnet, SSH), SNMP, RMON and Dual Image bring abundant management policies.

od113747/2022_2023 : Supply installation testing and commissioning of 8-Port Gigabit Smart PoE + Switch with 2 SFP Slots Features 8 802.3af/at compliant PoE + ports, with total PoE power budget of 116W and useful PoE power management features Gigabit Ethernet connections on all ports provide full speed of data transferring Advanced security features include IP?MAC-Port Binding, ACL, Port Security, DoS Defend, Storm Control, DHCP Snooping, 802.1X, and Radius Authentication L2/L3/L4 QoS and IGMP snooping optimize voice and video applications WEB/CLI managed modes, SNMP, RMON bring abundant management features Dual Firmware Image improves reliability and up-time of network

od113748/2022_2023 : Supply, installation, testing and commissioning of Server PC, Intel i7 processor 11 th generation, 24 inch LED monitor, Gigabit LAN port, USB port, 16GB, 16Gx1, DDR4, 2933MHz,256GB M.2 PCIe NVMe Solid State Drive + 1TB 7200 rpm 3.5.; SATA Hard Drive,2GB dual graphic card, 100/1000 LAN ports, optical mouse, Keyboard, DVD Writer. Genuine Windows 10 (with latest updation for the system) Home 64-bit English, 24 inch LED monitor, Mouse, keyboard, speaker set

od113749/2022_2023 : Supply, Installation, Testing and Commissioning of 600 VA OFF Line UPS for the above system Output Voltage: 230V Ac, 50 Hz ,1% Output Waveform: Pseudo Sine Wave Indications: Visual And Audio. Off-Mode Battery Charging With High Voltage Protection Backup Time : 10 -15 Minutes At Battery Full Charge Condition Capacity: 600Va/300W Battery Details: 12V, 7Ah - 1 No Cabinet Details: Abs

od113750/2022_2023 : Supply, Installation, Testing and commissioning of Internet gateway unified threat management for 50 concurrent users with 3 year subscription

od113751/2022_2023 : Providing and termination of CE Listed 19&rsquo;&rdquo; Easy Front Access (EFA) Sliding Rack Mount duplex type 24 Port LIU with modules splice Tray and Cable spool (SC) SM and including all accessories like pigtails, sleeves, etc complete.

od113752/2022_2023 : Providing and termination of CE Listed 19&rsquo;&rdquo; Easy Front Access (EFA) Sliding Rack Mount duplex type LIU 06 Port Blank with Splice Tray and Cable spool (SC) SM and including all accessories like pigtails, sleeves, etc complete

od113753/2022_2023 : Supply installation testing and commissioning of Cat 6/Cat 6A 24 Port fully-loaded patch panel with rear cable manager and necessary mechanical supports etc. complete

od113754/2022_2023 : Supply installation testing and commissioning of SFP Module 1 G

WIRELESS NETWORK SYSTEM od113683/2022_2023 : Supply, installation, testing and commissioning of Wireless Dual Band Ceiling Mount Access Point Ultra-Fast Wi-Fi 6 Speeds: Simultaneous 574 Mbps on 2.4 GHz and 1201 Mbps on 5 GHz totals 1775 Mbps Wi-Fi speeds. High-Density Connectivity: 4&times;increased capacity to connect more devices simultaneously. Integrated into SDN: Zero- touch;Provisioning (ZTP), Centralized Cloud Management, and Intelligent Monitoring. Centralized Management: Cloud access and app for ultra convenience and easy management. Seamless Roaming: Even video streams and voice calls are unaffected as users move between locations. PoE+ Support: Supports Power over Ethernet (802.3at) for convenient deployment and installation. Secure Guest Network: Along with multiple authentication options (SMS/Wi-Fi/ Voucher, etc.) and abundant wireless security technologies

od113690/2022_2023 : Supply, Installation, Testing and Commissioning of controller for the wireless access points capable of centralized management up to 500 access points, jet stream switches and Safe stream routers, cloud access, L3 management, multi site management, Automatic Device Discovery, Batch Configuration, Batch Firmware Upgrading, Intelligent Network Monitoring, Abnormal Event warnings, Unified Configuration, Reboot Schedule, Captive Portal Configuration with Ethernet Cable, Power Cord and Rackmount Kit

od113694/2022_2023 : Supply, Installation, testing and commissioning of WIFI Hotspot management solution for 500 users

CLOSED CIRCUIT TELEVISION (CCTV) SYSTEM od113681/2022_2023 : Supply, Installation, testing and commissioning of 2 MP IR DOME , 1/2.8&rdquo; CMOS image sensor, low illuminance, high image definition Outputs max. 2MP (1920 &times; 1080)@30 fps H.265 codec, high compression rate, low bit rate Built-in IR LED, max. IR distance: 50 m ROI, SMART H.264+/H.265+, flexible coding, applicable to various bandwidth and storage environments Rotation mode, WDR, 3D DNR, HLC, BLC, digital watermarking, applicable to various monitoring scenes Intelligent detection: Intrusion, tripwire (support the classification and accurate detection of vehicle and human) Abnormality detection: Motion detection, video tampering, scene&lt;br&gt;changing, audio abnormality detection, no SD card, SD card full, SD card error, network disconnection, IP conflict, illegal access, voltage detection Alarm: In, out; Audio: In, out; Supports max. 256 G Micro SD card 12V DC/POE power supply, IP67, IK10 protection, SMD Smart Motion Detection Certification, CE,FCC, UL, BIS

od113686/2022_2023 : 4MP Bullet , 1/3&rdquo; CMOS image sensor, low illuminance, high image definition Outputs max. 4MP (2688 &times; 1520)@30 fps, H.265 codec, high compression rate, low bit rate Built-in IR LED, max. IR distance: 50 m.ROI, SMART .264+/H.265+, flexible coding, applicable to various&lt;br&gt; bandwidth and storage environments. Rotation mode, WDR, 3D DNR, HLC, BLC, digital watermarking, applicable to various monitoring scenes. Intelligent detection: Intrusion, tripwire (support the classification and accurate detection of vehicle and human) Abnormality detection: Motion detection, video tampering, scene&lt;br&gt;changing, audio detection, no SD card, SD card full, SD card error, network disconnection, IP conflict, illegal access, voltage detection Supports max. 256 G Micro SD card, built-in Mic 12V DC/POE power supply IP67 protection SMD Smart Motion Detection Certification, CE,FCC, UL,BIS

od113689/2022_2023 : Supply, Installation, Testing and Commissioning of 4MP VARIFOCAL 2.7 mm&ndash;13.5 mm, F-1.5, field of range Horizontal: 104&deg;&ndash;27&deg;,Vertical: 55&deg; &ndash; 15&deg;&lt;br&gt;Diagonal: 124&deg; &ndash;31&deg;. 1/3&rdquo; CMOS image sensor, low illuminance, high image definition Outputs max. 4MP (2688 &times; 1520)@30 fps H.265 codec, high compression rate, low bit rate Built-in IR LED, max. IR distance: 60 m ROI, SMART H.264+/H.265+, flexible coding, applicable to various bandwidth and&lt;br&gt;storage environments Rotation mode, WDR, 3D DNR, HLC, BLC, digital watermarking, applicable to various monitoring scenes Intelligent detection: Intrusion, tripwire Abnormality detection: Motion detection, video tampering, scens changing, audio abnormality detection, no SD card, SD card full, SD&lt;br&gt;card error, network disconnection, IP conflict, illegal access, voltage detection Alarm: In, out; Audio: In, out; Supports max. 256 G Micro SD card 12V C/POE power support IP67, IK10(optional) protection SMD Smart Motion Detection Certification, CE,FCC, UL

od113696/2022_2023 : Supply, installation, testing and commissioning 32 Channel Network Video Recorder 32-channel IP video access Smart H.265+/Smart H.264+/H.265/H.264/MJPEG; H.265 auto switch Max 320 Mbps incoming bandwidth Up to 24MP resolution for live view and playback 1-channel fisheye dewarping (AI by NVR) AI by Camera: Perimeter protection; face detection and recognition; SMD Plus; video metadata; ANPR; people counting; stereo analysis; crowd distribution; heat map . Up to 22 face pictures/sec processing&lt;br&gt;&middot; Up to 20 face databases with 100,000 face images in total. Smart H.265+ is the optimized implementation of the H.265&lt;br&gt;codec that uses a scene-adaptive encoding strategy, dynamic GOP, dynamic ROI, flexible multi-frame reference structure and intelligent noise reduction to&lt;br&gt;deliver high-quality video without straining the network. ANPR Automatic Number Plate Recognition required for convenient entrance/ exit management. Support license plate recognition black/white list import/export, add/remove B/W list number, search result from recorded video. Internal HDD 8 SATA III Ports, Up to 10 TB capacity for each HDD eSATA 1 eSATA Interface 2 RJ-45 Ports (10/100/1000Mbps)Independent or Joint Working PoE N/A Network Function HTTP, HTTPS, TCP/IP, IPv4/IPv6, UPnP, SNMP, RTSP,UDP, SMTP, NTP, DHCP, DNS, IP Filter, PPPoE, DDNS,FTP, Alarm Server, IP Search (Support IP camera, DVR, NVS, etc.), P2P Max. User Access 128 users Smart Phone iPhone, iPad, Android Interoperability ONVIF 2.4, SDK, CGI Certification CE,FCC,UL,BIS

od113716/2022_2023 : Supply, installation, testing and commissioning of 24 Port GIGA POE switch with 4 SFP Module. Jet Stream 24-Port Gigabit Smart PoE+ Switch with 4 SFP Slots Supports 24 802.3at/af-compliant PoE+ ports with a total power supply of 192W L2+ Feature&mdash;&mdash;Static Routing, helps route internal traffic&lt;br&gt;for more efficient use of network resources IP-MAC-Port Binding, ACL, Port Security, DoS Defend, Storm control, DHCP Snooping, 802.1X and Radius Authentication provide you robust security strategies L2/L3/L4 QoS and IGMP snooping optimize voice and video applicationsIPv6 support with dual IPv4/IPv6 stack, MLD snooping, IPv6 neighbor discovery WEB/CLI managed modes, SNMP, RMON and Dual Image bring abundant management features&lt;br&gt;

od113720/2022_2023 : Supply, installation, testing and commissioning of 8 port- PoE switch with 2 SFP Module Gigabit Smart Switch is equipped with 8 gigabit RJ45 ports and 2 SFP slots, all RJ45 Ports support the 802.3af/at (PoE+) standard with total PoE power budget of 60W and useful PoE power management features. The switch provides high performance, enterprise-level QoS, useful security strategies and rich layer 2 management features. TP-Link&rsquo;s Jet Stream Gigabit Smart Switch is especially designed for the small and medium business networks that require efficient network management. The switch comes with a comprehensive set of features, such as Link Aggregation Group, 802.1Q VLAN, Access Control Lists (ACL), Quality of Service (QoS L2 to L4), Storm Control and IGMP Snooping to provide a small or medium-sized business with a network that is geared for growth while ensuring performance and reliability. What&rsquo;s more, its easy-to-use web management interface means faster setup and configuration with less downtime

od113724/2022_2023 : Supply, Installation, Testing and Commissioning of 8 port fully loaded Patch panel.

od113726/2022_2023 : Supply, Installation, Testing and Commissioning of fully loaded 12 port LIU

od113730/2022_2023 : Supply installation testing and commissioning of floor mount 22 U Network Rack 600 mm X 600 MM with cable manager, PDU 6 Socket, Cable Organizer 1U Closed, Fan &amp; Hardware Kit and all other accessories etc. complete

od113734/2022_2023 : Supply, installation, testing and commissioning of Surveillance/SATA compatible Hard Disk of 8 TB capacity to achieve the total storage for 30days @ 20fps for the NVR server

od113735/2022_2023 : Supply, Installation, Testing &amp; Commissioning of 55&apos;&apos; 4K LED Monitor with resolution 3840x2160 pixel including wall mounting accessories.

PUBLIC ADDRESS SYSTEM od113691/2022_2023 : Supplying, installation, testing &amp; commissioning of 6W ceiling speaker complete as required

od113697/2022_2023 : Supplying, installation, testing &amp; commissioning of ceiling/wall mounted loud&lt;br&gt;speaker, 6 Watt in ABS enclosure complete as required.

od113709/2022_2023 : Supply, installation, testing and commissioning of Voice Alarm Controller having all Heart of the Plena Voice Alarm System EN 54- 16 certified and EN 60849 compliant. Message manager and 240 W amplifier built-in Six-zone outputs 12 business and emergency control inputs Voltage 230/115VAC,&lt;br&gt;&plusmn;15%, 50/60 Hz Current inrush 8 A Max power consumption 600 VA. Voltage 24 VDC, +15% / -15% Current max 14 A. Output power (rms/maximum) 240 W /360 W Power reduction on backup power -1 dB. Frequency response 60 Hz to 18 kHz (+1/-3 dB at -10 dB ref. rated output) Distortion &lt;1% at rated output power, 1 kHz Bass control -8/+8 dB at 100 Hz Treble control -8/+8 dB at 10 kHz Mic/line input 1 x Connector XLR, 6.3 mm jack Sensitivity 1 mV (mic), 1 V (line) Impedance &gt;1 k ohm (mic); &gt;5 k ohm (line)S/N (flat at max volume) &gt;63 dB (mic); &gt;70 dB (line).S/N (flat at min volume/muted) &gt;75 dB CMRR &gt;40&lt;br&gt;dB (50 Hz - 20 kHz).Headroom &gt;25 db. Speech filter -3 dB at 315 Hz, high-pass, 6 dB/oct

od113714/2022_2023 : Supply, installation, testing and commissioning of Voice alarm Router to expand the Plena Voice Alarm System with six zones. EN 5416 certified.12 additional input contacts Six volume override output contacts. Supervision within the Plena Voice Alarm System Router

od113723/2022_2023 : Supply, installation, testing &amp; commissioning of 240 watts amplifier XLR inputs / output, Direct 100V input for power expansion, Excellent S/N &gt;85dB, Input level control, Low profile 2U housing, Low impedance output for 8 or 4 ohms output

od113727/2022_2023 : Supply, installation, testing and commissioning of Booster Amplifier 480 W

od113728/2022_2023 : Supply, installation, testing &amp; commissioning of DVD player for background Music

od113729/2022_2023 : Supplying drawing and testing of Single pair, 2-core, 1.5 sq mm Fire Retardant PVC insulated copper conductor speaker cable in the existing surface, surface/recessed pvc/steel conduit including connections and interconnections etc. as required

CABLE TELEVISION SYSTEM 1.19 : Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

od113685/2022_2023 : Supplying and drawing co-axial RG-11 copper cable in the existing surface/recessed steel/ pvc/hdpe conduit as required.;

1.24.7 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet

od113703/2022_2023 : Cable TV connection from operator which includes supply, installation, testing and commissioning of all accessories (including the set top box, antenna, amplifier whichever is required) for making the cable TV connection to the Television point

od113704/2022_2023 : Supply, Installation, Testing and Commissioning of 40 inch LED SMART TV with necessary supports/stands etc. complete

TELEPHONE SYSTEM 1.18.1 : Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor,unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.1 Pair

od113687/2022_2023 : Supply, Installation, Testing and Commissioning of 20 pair Telephone &amp; Switchboard cable with high density polyethylene insulated solid annealed high conductivity bare copper with dia 0.50 M paired polyester taped and sheathed with high oxygen index, fire retardant PVC Compound, generally confirming to ITD specifications&lt;br&gt;

od113702/2022_2023 : Supply, Installation, Testing and Commissioning of 50 pair Telephone &amp; Switchboard cable with high density polyethylene insulated solid annealed high conductivity bare copper with dia 0.50 M paired polyester taped and sheathed with high oxygen index, fire retardant PVC Compound, generally confirming to ITD specifications

od113708/2022_2023 : Supply, Installation, Testing and Commissioning of 100 pair Telephone &amp; Switchboard cable with high density polyethylene insulated solid annealed high conductivity bare copper with dia 0.50 M, paired polyester taped and sheathed with high oxygen index, fire retardant PVC Compound, generally confirming&lt;br&gt;to ITD specifications.

od113710/2022_2023 : Supply, Installation, Testing and commissioning of 20 pair Krone module fixed in box

od113717/2022_2023 : Supply, Installation, Testing and commissioning of 50 pair Krone module fixed in box

od113722/2022_2023 : Supply, Installation, Testing and Commissioning of 200 pair MS DP box with tele connector

1.24.6: Supplying and fixing following modular type switch / socket on the existing switch box/ cover including connections etc. as required.Telephone socket outlet

od113732/2022_2023 : Supply, Installation, Testing &amp; Commissioning of EPABX System, configured for trunk lines ,02 dkp port and 100 extensions(expandable upto 240 ports)DIGITAL VOICE MODULES - 08 OF 16 SECONDS EACH,AUDIO CONFERENCE &ndash; 15 PARTY,EXTERNAL MUSIC PORT &ndash; 1,PUBLIC ADDRESS SYSTEM PORT &ndash; 1,COMMUNICATION PORTS(RS-232 ),DIGITAL IN-PUT PORT( FOR SENSORS) &ndash; 1,DIGITAL OUT-PUT PORT ( FOR CONTROL) &ndash;1 &amp; ASMDR SOFTWARE FOR OUTGOING,INCOMING(INCLUDING MISSED CALLS &amp; INTERCOM CALL ).

od113733/2022_2023 : Supplying, installation, testing &amp; commissioning of ordinary telephones with connecting cords (minimum length of 2 metres) having necessary connector at both ends

ACCESS CONTROL SYSTEM od113680/2022_2023 : Supply of smart cards for the access

od113684/2022_2023 : Supply installation testing and commissioning of Proximity card readers

od113692/2022_2023 : Supply, installation, testing and commissioning of 4 Door / 8 Reader Controller: Supports access control of up to 4 doors in all respect including 4 entry readers, 4 exit readers, 4 locks, 4 exit switches etc. Inbuilt RJ45 Network Interface: Leveraging on the merits of IP based systems; it can easily be hooked up on the existing TCP/IP network. Thus the data can be transferred instantaneously in real time mode to a centralized server. Field Upgradable Firmware: Facility to onsite upgrade the firmware over Ethernet interface so that any customization or new version can be easily upgraded without any need of removing the device. Protected Enclosure: Both controller &amp; power supply unit are protected with suitable housing so that electronic circuit boards are not exposed to cause any accidental damage. Anti Pass Back: Door wise antipassback. Entry to the particular door is allowed only when the employee has exited through the same door. Door Interlocking: Facility of door interlocking is available. The system allows creating a group of doors such that access to a door within the group is allowed only when all the other doors are in closed condition

od113693/2022_2023 : Supply, Installation, Testing and Commissioning of Push Button switch with accessories

od113700/2022_2023 : Supply, Installation, Testing and Commissioning of Electromagnetic Lock with required mounting brackets etc. complete for single door/double door

od113706/2022_2023 : Supply, Installation, Testing and Commissioning of surface / flush mounted (as required at site) Magnetic Contact (Door position sensor) for access controlled doors;

od113718/2022_2023 : Supply and laying of 4 core 0.75 Sq. mm Un Armored FRLS, Multi stranded Copper Conductor, PVC sheathed Cable for connecting controller to Lock &amp; door position sensors, Buzzer, BGU, Push button etc. complete

od113721/2022_2023 : Supply and laying of 8 core 0.75 Sq. mm Un Armored FRLS, Multi stranded Copper Conductor, PVC sheathed Cable for connecting controller to Lock &amp; door position sensors, Buzzer, BGU, Push button etc. complete

od113725/2022_2023 : Supply installation, testing, commissioning of EDR (EMERGENCY BREAK GLASS )

NURSE CALL SYSTEM od113679/2022_2023 : Supply, Installation, Testing and Commissioning of Server PC having configurations 8 GB RAM DDR4, 4 GB GRAPHICS CARD, 512 GB SSD with expandable slot including 24 inch LED monitor, mouse, key board etc complete for operating the system completely and installation, programming, testing and commissioning of Nurse call system software pack for the server for automatically logging all eventsin the entire communications system such as calls, presence markings. All the report should be able to generate on real time basis without any delay. The License should be for life time without any additional cost in future.

od113682/2022_2023 : Supply, Installation, testing and commissioning of dome light with RGB indicator light providing different color indications as per requirement.

od113688/2022_2023 : Supply, Installation, Testing and Commissioning of toilet bath station with pull cord.

od113695/2022_2023 : Supply, installation, testing and commissioning of Patient nurse call outlets with call ,reset buttons excluding backbox and Wired Calling Remote for Patient to call the nurse(Ward bed, IP Rooms and ICU).

od113699/2022_2023 : Supply, installation, testing and commissioning of Nurse call Control Unit with substation monitoring and control, system data exchange control, power amplifier function, Host call function and alarm function.

od113707/2022_2023 : Supply, installation, testing and commissioning of Wireless Nurse console station with intercom having high resolution touch screen, multicolored indication lights, circular broadcasting, fault alarm, two way speech. UL 1069, NFPA 99, ANSI/IEEE 602, CE certified

VRF INDOOR UNITS od94904/2022_2023 : VRF Indoor Units ::Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc, suitable for operation on single phase AC supply 230V&plusmn;10%,50Hz complete as required.(VRF) 2.0 TR/800 CFM,TSP-25mm

od94909/2022_2023 : VRF Indoor Units ::Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc, suitable for operation on single phase AC supply 230V&plusmn;10%,50Hz complete as required.(VRF) 3.0 TR/1200 CFM,TSP-30mm

od94916/2022_2023 : &nbsp;VRF Indoor Units ::Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc. suitable for operation on single phase AC supply 230V&plusmn;10%,50Hz complete as required.(VRF) 4.0 TR/1600 CFM,TSP-40mm- 3F &amp.

od94922/2022_2023 : VRF Indoor Units ::Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc. suitable for operation on single phase AC supply 230V&plusmn;10%,50Hz complete as required.(VRF) 5.0 TR/2000 CFM,TSP-30mm.

od94926/2022_2023 : VRF Indoor Units :Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter,fan section with low noise fan/dynamically balanced blower,multispeed motor,coil section with DX copper coil,electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc. suitable for operation on single phase AC supply 230V&plusmn;10%,50Hz complete as required.(VRF) 6.0 TR/2400 CFM,TSP-50mm.

od94934/2022_2023 : VRF Indoor Units :Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter,fan section with low noise fan/dynamically balanced blower,multispeed motor,coil section with DX copper coil,electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc. suitable for operation on single phase AC supply 230V&plusmn;10%,50Hz complete as required.(VRF) 1.5 TR/600 CFM,TSP-25mm.

od94940/2022_2023 : High Wall Unit:-Supply, installation, testing and commissioning of following minimum capacity high wall units with multilevel filter for better air quality ,auto restart and multimode.(VRF) 1.0 TR/350 CFM.

od94942/2022_2023 : Supply installation testing and commissioning of following minimum capacity high wall units with multilevel filter for better air quality ,auto restart and multimode.(VRF) .1.5 TR/500 CFM.

od94950/2022_2023 : Supply installation testing and commissioning of cabinet type Double skin (43 mm insulation with thermal break profile) Floor mounted AHU for Operation theatres. The Air Handling Unit shall consist of Mixing Box with fresh air intakes with dampers, filter section with10 micron Pre filter, 5 micron fine filter , Coil section( with 8 Row DX cooling coil),Dehumidifier, Pressure switch for filter contamination control, Humidity and temperature sensor on return air duct, all data&apos;s and control shall be given to OT control panel including wiring, DIDW backward curved fan, access door, canopy, marine light, EFF1 quality motor of suitable rating and drive package for fan For motor efficiency as per IS 12615 rating shall be IE2, canvas at unit outlet, outlet damper, &amp; spring type vibration isolators for the fans. Rubber pads shall be provided between the unit frame and the concrete base frame.(VRF) , 8.0 TR / 3200 CFM, TSP - 100 mm, Floor mounted type.

od94953/2022_2023 : Supply installation testing and commissioning of cabinet type Double skin (25 mm insulation) Ceiling suspended/Floor Mounted AHU complete with pre filter, fine filter at supply duct,6 row DX cooling coil, Backward curved fan, motor with For motor efficiency as per IS 12615 rating shall be IE2 and drive package for fan, canvass at unit outlet, outlet damper, vibration isolators. Outlet Velocity of the fan to be restricted to 9.5 m/s, necessary vibration isolation arrangement etc. complete as per specification and of following capacities of CSU - 8.5 TR / 3400 CFM, TSP - 90 MM.(VRF)

od94959/2022_2023 : Supply installation testing and commissioning of &nbsp;Cabinet type Double skin (25 mm insulation) Ceiling suspended/Floor mounted AHU complete with pre filter, fine filter at supply duct, 6 row DX cooling coil, Backward curved fan, motor with For motor efficiency as per IS 12615 rating shall be IE2 and drive package for fan, canvass at unit outlet, outlet damper, vibration isolators.Outlet Velocity of the fan to be restricted to 9.5 m/s, necessary vibration isolation arrangement etc. complete as per specification and of following capacities of CSU - 5.0TR / 2000 CFM, TSP - 50 MM.(VRF)

LOW SIDE 16.12.1.1 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 0.6 mm thick

16.12.1.2 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 0.8 mm thick

16.12.1.3 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular dueling as per IS 655-2006 for 1 mm thick

16.12.1.4 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.factory fabricated GSS sheet metal rectangular dueling as per IS 655-2006 for 1.25 mm thick

16.12.2.1 : Supply, Installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, etc as per approved drawings and specifications of following sheet thickness complete as required.Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 0.63 mm thick

od94927/2022_2023 : Supply, installation, balancing and commissioning of factory fabricated Aluminium sheet metal rectangular/round ducting for OT&apos;s complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of Thickness 22G sheet.

16.13 : Supply, Insulation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications. GI volume control duct damper

od94935/2022_2023 : Supply, Installation, testing and commissioning of motorized GI volume control duct damper ,High quality Galvanized Steel sheet of thickness 1.2mm as standard. complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications

16.15 : Suppluying and Fixing of powder costed extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

od94944/2022_2023 : Supplying &amp; fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

16.17 : Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminum with aluminum volume control dampers with anti smudge ring and removable core.

16.18 : Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminum without volume control dampers with anti smudge ring and removable core.

od94954/2022_2023 : Supply, installation, testing &amp; commissioning of Butter fly dampers of GI construction made out of 20G sheet with lever, brass bush with spindle and locking arrangement at the take off for the supply air diffusers. complete as required as per specifications of 150 mm dia

od94957/2022_2023 : Supply, installation, testing &amp; commissioning of Butter fly dampers of GI construction made out of 20G sheet with lever, brass bush with spindle and locking arrangement at the take off for the supply air diffusers. complete as required as per specifications of 200 mm dia

od94960/2022_2023 : Supply, installation, testing &amp; commissioning of Butter fly dampers of GI construction made out of 20G sheet with lever, brass bush with spindle and locking arrangement at the take off for the supply air diffusers. complete as required as per specifications of 250 mm dia

od94962/2022_2023 : Supply, installation, testing &amp; commissioning of thermal insulated flexible duct of following sizes duly supported at regular interval as per site requirement etc. complete as required as per specifications. Thermal insulated flexible duct 150mmdia

16.19.1 : Supplying, installation, testing & commissioning of thermal insulated flexible duct of following sizes duly supported at regulator interval as per site requirement etc. complete as required as per specifications.Thermal insulated flexible duct (200 mm dia)

od94966/2022_2023 : Supply, installation, testing &amp; commissioning of thermal insulated flexible duct of following sizes duly supported at regular interval as per site requirement etc. complete as required as per specifications. Thermal insulated flexible duct 250mmdia

od94969/2022_2023 : Supplying and fixing of following thickness closed cell Nitrile rubber Anti- Microbial (class &ldquo;O&rdquo;) insulation on duct after applying two coats of cold setting synthetic rubber based adhesive of suitable grade. The all joints shall sealed cotton tape insulation complete as per specifications and 19 mm thick with density of Material between 40 to 60 Kg/m3.

od94970/2022_2023 : Supplying and fixing of following thickness closed cell Nitrile rubber Anti- Microbial (class &ldquo;O&rdquo;) insulation on duct after applying two coats of cold setting synthetic rubber based adhesive of suitable grade. The all joints shall sealed cotton tape insulation complete as per specifications and 13 mm thick with density of Material between 40 to 60 Kg/m3.

od94973/2022_2023 : Supply and fixing of acoustic insulation of supply air duct with open cell anti microbial nitrile rubber of 200 kg/m3 density with 10mm thickness.

od94975/2022_2023 : Supply installation of Factory fabricated double skin plenum of 25mm thick PUF panels of density 40 kg/cum, casing inside &amp; outside material - GI &amp; casing inside &amp; outside thickness - 0.6 mm. The area indicated is the surface area of the plenum.

16.20.1 : Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/ main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications.Fire damper

16.20.2 : Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/ main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications.Actuator

16.21.1 : Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m3, with 25 mm X 25 mm Gl section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications. 16 <br> <br>Acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m3Acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m3

16.25.1 : Supplying and fixing 50mm thick aluminium foil faced resin bonded fibre glass insulation (on duct) of density 24 kg/cu.m or mineral wool insulation(non combustible) of density 44 kg/cum after applying two coats of cold setting adhesive (CPRX compound) sealing all joints with self adhesive aluminium tape & covering with 0.63mmx19mm GI wire mesh netting & butting all joints and laced with GI wire complete and finally covered with one layer of tar felt stuck with hot bitumen as per specifications and as required. (for outdoor applications). 50 mm thick

od94980/2022_2023 : Supplying and Fixing of Polyester Insulation made of 50mm thick Underdeck Insulation 500 GSM with the backing of Aluminium foil. The Product shall be eco Friendly and having sound absorption/thermal insulation properties. Light weight, easy and safe for Installation.

od94981/2022_2023 : Supply installation of Opposed blade collar dampers of powder coated Aluminium.

od94982/2022_2023 : Supplying, fixing of powder coated extruded aluminium section fresh air grill with aluminium volume control dampers, bird screen etc complete as required

od94983/2022_2023 : Supply installation of Non Vision grills for the toilet doors. The grills shall be supplied in two matching halves and shall match the door thickness. The grills shall be powder coated .

od94984/2022_2023 : Supplying, fixing testing commissioning of Exhaust Disc Valve.

od94985/2022_2023 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &amp; fittings with one step PVC solvent cement and testing of joints with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of 9 mm thick complete as per direction of Engineer -in-Charge 50 mm dia 10 Kgf/cm2- Internal work - exposed on wall

od94986/2022_2023 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &amp; fittings with one step PVC solvent cement and testing of joints with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of 9 mm thick complete as per direction of Engineer -in-Charge 40 mm dia 10 Kgf/cm2- Internal work - exposed on wall

od94987/2022_2023 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &amp; fittings with one step PVC solvent cement and testing of joints with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of 9 mm thick complete as per direction of Engineer -in-Charge 32 mm dia 10 Kgf/cm2- Internal work - Exposed on wall

od94988/2022_2023 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &amp; fittings with one step PVC solvent cement and testing of joints with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of 9 mm thick complete as per direction of Engineer -in-Charge 25 mm dia 10 Kgf/cm2- Internal work - Exposed on wall

od94989/2022_2023 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &amp; fittings with one step PVC solvent cement and testing of joints with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of 9mm thick complete as per direction of Engineer -in-Charge 20 mm dia 10 Kgf/cm2- Internal work - Exposed on wall

MECHANICAL VENTILATION AND EXHUAST FANS od94898/2022_2023 : &nbsp;Circular type inline fan consisting of back ward curved impeller which is factory matched to the corresponding dynamically balanced for vibration free operation for with necessary fixing arrangements. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 200 cfm , TSP - 15 mm

od94907/2022_2023 : Circular type inline fan consisting of back ward curved impeller which is factory matched to the corresponding dynamically balanced for vibration free operation with necessary fixing arrangements. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 400 cfm , TSP - 20 mm.

od94912/2022_2023 : Circular type inline fan consisting of back ward curved impeller which is factory matched to the corresponding dynamically balanced for vibration free operation with necessary fixing arrangements. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 500 cfm , TSP - 20 mm

od94918/2022_2023 : Circular type inline fan consisting of back ward curved impeller which is factory matched to the corresponding dynamically balanced for vibration free operation with necessary fixing arrangements. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 1000 cfm , TSP - 20 mm

od94933/2022_2023 : Inline type fan suitable for ducted exhaust air application for OT fumigation consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 2200 cfm , TSP - 30 mm.

od94939/2022_2023 : Inline type fan suitable for ducted exhaust application consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 1200 cfm , TSP - 20 mm

od94943/2022_2023 : Inline type fan suitable for ducted fresh air application consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level.Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 1000 cfm , TSP - 20 mm

od94948/2022_2023 : &nbsp;Inline type fan suitable for ducted fresh air application consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 800 cfm , TSP - 20 mm

od94951/2022_2023 : Inline type fan suitable for ducted fresh air application consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 600 cfm , TSP - 20 mm

od94952/2022_2023 : Inline type fan suitable for ducted fresh air application consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 300 cfm , TSP - 10 mm

od94955/2022_2023 : Inline type fan suitable for ducted fresh air application consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 200 cfm , TSP - 10 mm

od94958/2022_2023 : Double skin cabinet type fan suitable for ducted exhaust application consisting of 25mm thick cabinet, HEPA filter, backward curved fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level. Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 800 cfm , TSP - 50 mm

od94974/2022_2023 : Wall mounted type propeller fan of single phase for toilet exhaust should be complete with mounting plate, shaft, fan blades, motor, Fan motor shall have necessary rating to meet ECBC 2017 compliance, drive package &amp; necessary supports. Supply, installation, testing and commissioning of Wall mounted type propeller fan 1000 CFM

od94977/2022_2023 : Wall mounted type propeller fan of single phase for toilet exhaust should be complete with mounting plate, shaft, fan blades, motor, Fan motor shall have necessary rating to meet ECBC 2017 compliance, drive package &amp; necessary supports. Supply, installation, testing and commissioning of Wall mounted type propeller fan 400 CFM

od94979/2022_2023 : &nbsp;Wall mounted type propeller fan of single phase for toilet exhaust should be complete with mounting plate, shaft, fan blades, motor, Fan motor shall have necessary rating to meet ECBC 2017 compliance, drive package &amp; necessary supports. Supply, installation, testing and commissioning of Wall mounted type propeller fan 100 CFM

REFRIGERANT PIPING od94901/2022_2023 : Supply, Installation, testing and commissioning including vaccumization and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping, complete with fittings, with suitable adjustable ring type hanger supports on PVC sleeves, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines and sealed with adhesive type black cotton tape, all accessories as per specifications etc. as required. 1/4 .; dia (6.4 MM-OD) soft drawn with tube thickness 1.2mm and 13 mm thick insulation.

od94906/2022_2023 : Supply, Installation, testing and commissioning including vaccumization and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping, complete with fittings, with suitable adjustable ring type hanger supports on PVC sleeves, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines and sealed with adhesive type black cotton tape, all accessories as per specifications etc. as required. 3/8 .; dia (9.5 MM-OD) soft drawn with tube thickness 1.2mm and 13 mm thick insulation.

od94914/2022_2023 : Supply, Installation, testing and commissioning including vaccumization and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping, complete with fittings, with suitable adjustable ring type hanger supports on PVC sleeves, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines and sealed with adhesive type black cotton tape, all accessories as per specifications etc. as required. 1/2 .; dia (12.7 MM-OD) soft drawn with tube thickness 1.2mm and 13 mm thick insulation.

od94917/2022_2023 : Supply, Installation, testing and commissioning including vaccumization and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping, complete with fittings, with suitable adjustable ring type hanger supports on PVC sleeves, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines and sealed with adhesive type black cotton tape, all accessories as per specifications etc. as required. 5/8 .; dia (15.86 MM-OD) soft drawn with tube thickness 1.2mm and 13 mm thick insulation.

od94924/2022_2023 : Supply, Installation, testing and commissioning including vaccumization and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping, complete with fittings, with suitable adjustable ring type hanger supports on PVC sleeves, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines and sealed with adhesive type black cotton tape, all accessories as per specifications etc. as required. 3/4 .; dia (19 MM-OD) hard drawn with tube thickness 1.2mm and 13 mm thick insulation.

od94930/2022_2023 : Supply, Installation, testing and commissioning including vaccumization and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping, complete with fittings, with suitable adjustable ring type hanger supports on PVC sleeves, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines and sealed with adhesive type black cotton tape, all accessories as per specifications etc. as required. 7/8 .; dia (22.2 MM-OD) hard drawn with tube thickness 1.2mm and 19 mm thick insulation.

od94932/2022_2023 : Supply, Installation, testing and commissioning including vaccumization and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping, complete with fittings, with suitable adjustable ring type hanger supports on PVC sleeves, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines and sealed with adhesive type black cotton tape, all accessories as per specifications etc. as required. 1 .; dia (25.4 MM-OD) hard drawn with tube thickness 1.2mm and 19 mm thick insulation.

od94936/2022_2023 : Supply, Installation, testing and commissioning including vaccumization and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping, complete with fittings, with suitable adjustable ring type hanger supports on PVC sleeves, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines and sealed with adhesive type black cotton tape, all accessories as per specifications etc. as required. 1-1/8 .; dia (28.58 MM-OD) hard drawn with tube thickness 1.2mm and 19 mm thick insulation.

od94941/2022_2023 : Supply, Installation, testing and commissioning including vaccumization and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping, complete with fittings, with suitable adjustable ring type hanger supports on PVC sleeves, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines and sealed with adhesive type black cotton tape, all accessories as per specifications etc. as required. 1-1/4 .; dia (31.8 MM-OD) hard drawn with tube thickness 1.62mm and 19 mm thick insulation.

od94945/2022_2023 : Supply, Installation, testing and commissioning including vaccumization and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping, complete with fittings, with suitable adjustable ring type hanger supports on PVC sleeves, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines and sealed with adhesive type black cotton tape, all accessories as per specifications etc. as required. 1-3/8 .; dia (34.9 MM-OD) hard drawn with tube thickness 1.62mm and 19 mm thick insulation.

od94946/2022_2023 : Supply, Installation, testing and commissioning including vaccumization and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping, complete with fittings, with suitable adjustable ring type hanger supports on PVC sleeves, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines and sealed with adhesive type black cotton tape, all accessories as per specifications etc. as required. 1-1/2 .; dia (38.1 MM-OD) hard drawn with tube thickness 1.62mm and 19 mm thick insulation.

od94949/2022_2023 : Supply, Installation, testing and commissioning including vaccumization and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping, complete with fittings, with suitable adjustable ring type hanger supports on PVC sleeves, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines and sealed with adhesive type black cotton tape, all accessories as per specifications etc. as required. 1-5/8 .; dia (41.27 MM-OD) hard drawn with tube thickness 1.62mm and 19 mm thick insulation.

Miscellaneous items od94900/2022_2023 : &nbsp;Supply Installation Testing &amp; Commissioning of Expansion valve Kit with control box panel as per OEM specification.

od94903/2022_2023 : Supply Installation Testing and Commissioning of (VRF/VRV) ODU connecting Kit as per OEM.

od94911/2022_2023 : Supply installation testing &amp; commissioning of refnet joints as per manufacturer recommendation

od94919/2022_2023 : &nbsp;Centralized microprocessor based controller capable of controlling the entire system from a central location. This shall facilitate ON / OFF, temperature setting, fan speed, swing state of the louvers, run time scheduling etc of all the indoor units. The controller shall detect and display the status and various operating parameters of the outdoor units and the indoor units. The controller shall be BMS compatible.

od94923/2022_2023 : &nbsp;Supply and installation of HEPA Filter as per BSEN 779 Standard H12/H13 with media micro glass fiber paper. Construction is in a flange or box type in aluminium / SS frame. Shall be placed on supply duct having the same size properly fix inside duct with necessary support.

od94928/2022_2023 : Supply Installation Testing &amp; Commissioning of SS grade plenum of 600 x 1200 mm consisting of mini pleat HEPA filter, collar, volume control damper and access to filter. The arrangement should be suitable to mount above the OT Table. The unit shall be provided with a perforated Aluminum sheet at the bottom for air discharge with 475 CFM flow.

1.17.2 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.2 x 1.5 sq. mm

od94910/2022_2023 : High Wall Unit :-Supply, installation, testing and commissioning of inverter type 5 star rated high wall mounted Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cordless remote control, drain pan, necessary accessories etc, suitable for operation on 230V&plusmn;10%,50Hz,single phase AC supply, complete as required. The unit shall have automatic force shutdown provision incase of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. This price inclusive of outdoor unit with necessary support and hangers. CAPACITY :1.5 TR - UB Pharmacy Store

od94920/2022_2023 : &nbsp;High Wall Unit :-Supply, installation, testing and commissioning of inverter type 3 star rated high wall mounted Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cordless remote control, drain pan, necessary accessories etc, suitable for operation on 230V&plusmn;10%,50Hz,single phase AC supply, complete as required. The unit shall have automatic force shutdown provision incase of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. This price inclusive of outdoor unit with necessary support and hangers. CAPACITY :2.0 TR For Paywards

FIRE PROTECTION SYSTEM

od97546/2022_2023 : Supplying, installing, testing and commissioning of double flanged Rubber Expansion Bellows/ joint of standard length as per manufacturers specs including rubber PTFE / Asbestos free gaskets, flanges, nuts, bolts and washers complete as required. (Suction and Discharge side PN16) 150mm nominal diameter

od97554/2022_2023 : Providing and fixing of exhaust pipe M.S. Medium grade for Diesel engine shall not be smaller in diameter than engine exhaust outlet extended outside pump house, duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, flexible exhaust connection, residential silencer, instruments and protection as per specification NFPA 20 ,2016 with stand &amp; gauge glass, painting, rain cap and necessary supports as required.

od97566/2022_2023 : 1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing &amp; commissioning of suitable FRLS,PVC outer sheathe, steel armored, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The minimum size of the cables shall as mentioned below, 3.5C x 120 sq.mm aluminum for main pumps

od97574/2022_2023 : 1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing &amp; commissioning of suitable FRLS,PVC outer sheathe, steel armored, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The minimum size of the cables shall as mentioned below, 4 C x 16 Sqmm. Aluminum Jockey pump

od97579/2022_2023 : 1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing &amp; commissioning of suitable FRLS,PVC outer sheathe, steel armored, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The minimum size of the cables shall as mentioned below, 12 C x 2.5 Sqmm. copper Diesel engines

od97584/2022_2023 : 1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing &amp; commissioning of suitable FRLS,PVC outer sheathe, steel armored, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The minimum size of the cables shall as mentioned below, 2 C x 2.5 Sqmm copper armoured for Instrumentation.

od97587/2022_2023 : Supply and laying of 8 SWG copper wire through ceiling / walls, from the equipment to the nearest Earth pit/Earth bus with necessary accessories as required. (Earth pit shall be executed by other agencies).

od97594/2022_2023 : Providing and fixing 25mm x 3mm copper strip on surface or in recess for connections etc as required.

4.1.2 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.150 mm width X 50 mm depth X 1.6 mm thickness

4.1.4 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.300 mm width X 50 mm depth X 1.6 mm thickness

od97586/2022_2023 : Providing laying, testing &amp; commissioning of &apos;C&apos; class heavy duty GI Pipe conforming to IS 1239 part 1 fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation &amp; providing cement concrete blocks as supports, anticorrosive treatment with coal tar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 200 mm. Diameter

od97588/2022_2023 : Providing laying, testing &amp; commissioning of &apos;C&apos; class heavy duty GI Pipe conforming to IS 1239 part 1 fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation &amp; providing cement concrete blocks as supports, anticorrosive treatment with coal tar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 150 mm. Diameter

VALVES AND ACCESSORIES od97515/2022_2023 : Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 16) swing check type with required flanges, nuts, bolts 15mm thick compressed asbestos gasket including matching flanges complete ,GI bolts, nuts, washers etc.as required. 200 mm nominal diameter

od97517/2022_2023 : Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 16) swing check type with required flanges, nuts, bolts 15mm thick compressed asbestos gasket including matching flanges complete ,GI bolts, nuts, washers etc.as required. 150 mm nominal diameter

od97537/2022_2023 : Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 16) swing check type with required flanges, nuts, bolts 15mm thick compressed asbestos gasket including matching flanges complete ,GI bolts, nuts, washers etc.as required. 100 mm nominal diameter

od97548/2022_2023 : Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 16) swing check type with required flanges, nuts, bolts 15mm thick compressed asbestos gasket including matching flanges complete ,GI bolts, nuts, washers etc.as required. 80 mm nominal diameter

od97551/2022_2023 : Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 16) swing check type with required flanges, nuts, bolts 15mm thick compressed asbestos gasket including matching flanges complete ,GI bolts, nuts, washers etc.as required. 50 mm nominal diameter

od97557/2022_2023 : Supplying, Installing, testing and commissioning CI butterfly valves as per BS 5155 (PN 16) slim seal standard lever operated type, Valve should be fitted with supervisory /Tamper switch and same to connect to FA panel for monitoring the status of the valve and with sizes required flanges, nuts, bolts etc. complete. 200 mm nominal diameter

od97570/2022_2023 : Supplying, Installing, testing and commissioning CI butterfly valves as per BS 5155 (PN 16) slim seal standard lever operated type, Valve should be fitted with supervisory /Tamper switch and same to connect to FA panel for monitoring the status of the valve and with sizes required flanges, nuts, bolts etc. complete. 150 mm nominal diameter

od97575/2022_2023 : Supplying, Installing, testing and commissioning CI butterfly valves as per BS 5155 (PN 16) slim seal standard lever operated type, Valve should be fitted with supervisory /Tamper switch and same to connect to FA panel for monitoring the status of the valve and with sizes required flanges, nuts, bolts etc. complete. 100 mm nominal diameter

od97580/2022_2023 : Supplying, Installing, testing and commissioning CI butterfly valves as per BS 5155 (PN 16) slim seal standard lever operated type, Valve should be fitted with supervisory /Tamper switch and same to connect to FA panel for monitoring the status of the valve and with sizes required flanges, nuts, bolts etc. complete. 80 mm nominal diameter

od97583/2022_2023 : Supplying, Installing, testing and commissioning CI butterfly valves as per BS 5155 (PN 16) slim seal standard lever operated type, Valve should be fitted with supervisory /Tamper switch and same to connect to FA panel for monitoring the status of the valve and with sizes required flanges, nuts, bolts etc. complete. 50 mm nominal diameter

od97589/2022_2023 : Supply, installation, testing and commissioning of Y-Strainer PN-16 rating. Body: Cast Iron with Powder coating, Stainless Steel filter screen/mesh. The cost shall be inclusive of mating flanges of appropriate class, Asbestos free gasket, washers, nut and bolts etc. complete. 150mm dia.

od97593/2022_2023 : Supply, installation, testing and commissioning of Y-Strainer PN-16 rating. Body: Cast Iron with Powder coating, Stainless Steel filter screen/mesh. The cost shall be inclusive of mating flanges of appropriate class, Asbestos free gasket, washers, nut and bolts etc. complete. 200mm dia.

od97595/2022_2023 : Supply, Fixing, Testing and commissioning of double flanged sluice valve of rating PN 16 as per IS:780 with non rising spindle type, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and confirming to IS 780 of following size 50 mm nominal diameter

od97599/2022_2023 : Supply, Fixing, Testing and commissioning of double flanged sluice valve of rating PN 16 as per IS:780 with non rising spindle type, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and confirming to IS 780 of following size 150 mm nominal diameter

od97602/2022_2023 : Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valve with fittings of screwed end type. 50 mm diameter

od97604/2022_2023 : Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valve with fittings of screwed end type. 25 mm diameter

od97605/2022_2023 : supply installation of UL listed pressure gauge 1/4&apos;&apos; BSPT, minimum 3.5&apos;&apos; dial of suitable range to be installed in pump room suction, discharge, diesel pump and Sprinkler &amp; Standpipe Systems. Dial type White background black graduation scale with dual reading in Kg./ Sq.cm and PSI complete as required.

od97606/2022_2023 : Providing &amp; fixing heavy forged brass tested ISI marked 2280 Lpm Flow Pressure Relief valves (16 Bar) of approved quality with all necessary Piping connections till the Bypass valve to Water Tank (To be installed in diesel pump Header in Pump Room)

od97608/2022_2023 : &nbsp;Supply, fixing, testing and commissioning of zone control valve assembly with bypass unit, signaling butterfly valve 150mm, flow switch 150mm, pressure gauge 1/4&apos;&apos;, Test and Drain valve 50mm, all of them are UL Listed and FM Approved, conforming to BS 5306-2/ EN 12845 complete as required

od97523/2022_2023 : Supplying, installation, testing &amp; commissioning of intelligent interface unit BACnet/Modbus protocol i.e. supplying communication links between building management system and fire alarm control panel complete as required.

od97529/2022_2023 : Supplying, installation, testing &amp; commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.

od97539/2022_2023 : Supplying, installation, testing &amp; commissioning of repeater panel with 320 character / Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

od97541/2022_2023 : Supplying, installation, testing &amp; commissioning of intelligent analog addressable photo thermal detector complete with mounting base complete as required.

od97550/2022_2023 : Supplying, installation, testing &amp; commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc.;as required

od97560/2022_2023 : Supplying, installation, testing &amp; commissioning of fault isolator complete with base as required

od97564/2022_2023 : Supplying, installation, testing &amp; commissioning of intelligent addressable thermal detector with rate of rise cum fixed temperature thermistor complete with base as required.

od97577/2022_2023 : Supplying, installation, testing &amp; commissioning of addressable fire control module complete as required.

od97582/2022_2023 : Supply, Installation, testing and commissioning of UL Listed Intelligent Addressable Control Module for Fire Damper, Access Controllers , PA System Integration with necessary accessories complete as required.

od97590/2022_2023 : Providing and fixing Analogue Addressable Monitor module for monitoring the field devices &amp; shall be capable of providing DPDT contact rated at 24v DC, 2A. ( for flow switches)

od97592/2022_2023 : Providing and installation of Analogue Addressable Control relay module for AHU tripping and shall be capable of providing DPDT contact rated at 24v DC, 2A.

od97596/2022_2023 : Supplying, installation, testing &amp; commissioning of intelligent addressable duct detector including suitable Photo detector complete with base as required.

od97598/2022_2023 : Supplying, installation, testing &amp; commissioning of addressable manual call point complete as required.

od97600/2022_2023 : Supplying, installation, testing &amp; commissioning of addressable horn cum strobe&lt;br&gt;complete as required.

od97603/2022_2023 : Supplying &amp; laying of 2x1.5 Sq.mm fire alarm armored cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armoring &amp; FRLS outer sheath complete as required.

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

od97607/2022_2023 : Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

od97610/2022_2023 : &nbsp;Supply and fixing of Talk back speaker unit 5W LMT, Press to talk switch MS housing with Red color.

od97611/2022_2023 : Supplying &amp; laying of 4Cx1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring &amp; FRLS outer sheath complete as required.

HYDRANT SYSTEM od97516/2022_2023 : Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal coupling of 63 mm diameter with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal cap and chain as required :

od97518/2022_2023 : Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required ,30 meter length ,20 mm nominal internal diameter water hose thermoplastic (Textile reinforced) type -2 as per IS:12585.20 mm nominal internal diameter gun metal globe valve &amp; nozzle. Drum and brackets for fixing the equipment&apos;s on wall. Connections from riser with 25 mm diameter stop gun metal valve &amp; M.S. Pipe and socket.

od97553/2022_2023 : Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm diameter instantaneous FM Gunmetal coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal cap and chain as required

od97563/2022_2023 : Supplying and fixing 63 mm diameter, 15 m long RRL hose pipe with 63 mm diameter male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required.

od97565/2022_2023 : Supplying &amp; fixing 63 mm diameter gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

od97585/2022_2023 : Supplying, installation, testing and commissioning of 25 mm diameter Gunmetal single acting type Automatic Air Release Valve screwed ends, Pressure gauge and an isolation valve for wet riser. The max working pressure shall be 12 bar. BSP threaded male inlet, including necessary accessories and connections.

od97591/2022_2023 : Supplying and fixing air cushion vessel of continuous welded construction, made of 200 mm diameter, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm diameter gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.

FIRE EXTINGUISHERS od97511/2022_2023 : Supplying, installing and commissioning Portable Fire extinguishers of following type capacity. All to be confirmed to latest BIS codes(IS 2878:2004):-Carbon-di- oxide type fire extinguisher of 4.5 kg. Capacity, CO2 gas filled in brand new seamless cylinder with powder coated finish, with wheel type valve, discharge nozzle, bend horn, wall mounting bracket, signages etc. complete,

od118717/2022_2023 : Supplying, installing and commissioning Modular Ceiling Mounted Automatic Clean Agent Fire Suspension System, CE Certified, filled with 10 Kg UL listed Novec Gas, Pure Polyester powder coated body, complete with CE approved stainless steel solenoid valve, high durability Vinyl label, System performance certification by National Test House (Govt of India) with all mounting accessories etc. to complete the work

od97519/2022_2023 : Supplying, installing and commissioning Portable Fire extinguishers of following type &amp; capacity. All to be confirmed to latest BIS codes(IS 15683:2006):-Mechanical Foam(AFFF) type fire extinguisher 9Lts. Capacity, with initial filling in brand new cylinder with powder coated finish, high pressure CO2 gas cartridge, discharge hose and ABS type branch pipe and wall mounting bracket,signage etc. complete.

od97527/2022_2023 : Supplying, installing and commissioning Portable Fire extinguishers of following type capacity. All to be confirmed to latest BIS codes(IS 15683:2006):-ABC powder type fire extinguisher of 6 Kg. Capacity, with initial filling in brand new cylinder with powder coated finish, high pressure, discharge hose, wall mounting bracket, signages etc. complete.

od97534/2022_2023 : Supplying, installing and commissioning Portable Fire extinguishers of following type capacity. All to be confirmed to latest BIS codes(IS 15683:2006):- Water type of 6Ltrs. Capacity, with initial filling in brand new cylinder with powder coated finish, high pressure, discharge hose, wall mounting bracket, signages etc. complete.

od97543/2022_2023 : Supplying, installing Fire bucket stand fabricated by MS tube red colour enamel painted with minimum size 5X3 ft to install 4 Nos. of buckets with shade cover of Galvanized sheet thickness 20G.

od97556/2022_2023 : Supplying, installing Fire buckets 9L round bottom type enamel painted, white inside &amp; Red out side and Letter .;FIRE.; out side in black/white as instructed by site engineer and handle with mounting bracket.

AUTOMATIC SPRINKLER SYSTEM od97509/2022_2023 : Providing, fixing, testing &amp; commissioning of 15mm diameter quartzoid bulb type sprinklers screwed end connection of rating 68 degree centigrade Value 80 with required accessories : Pendent Sprinkler/Horizontal side wall sprinkler

od97520/2022_2023 : Providing, fixing, testing commissioning of 15mm diameter quartzoid bulb type sprinklers screwed end connection of rating 68 degree centigrade Value 80 with required accessories : Upright Sprinkler

od97540/2022_2023 : Providing & fixing of pressure switch in pipe line including connection etc. as required

od97544/2022_2023 : Providing &amp; fixing of flow switch on sprinkler distribution header on each floor and shall be connected to fire alarm panel through cable. Cable shall be measured separately, following sizes of fire pipe including connection etc. as required. 100mm diameter

od97549/2022_2023 : Providing &amp; fixing of flow switch on sprinkler distribution header on each floor and shall be connected to fire alarm panel through cable. Cable shall be measured separately, following sizes of fire pipe including connection etc. as required. 150mm diameter

od97561/2022_2023 : Providing, fixing, testing &amp; commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc. of following sizes as required :150 mm diameter

od97569/2022_2023 : Supplying, installation, testing &amp; commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stock bar of following sizes complete as required. Length : 1200 mm

od97571/2022_2023 : Providing, installation, testing &amp; commissioning of adjustable rosette plate for 15mm diameter, fabricated by M.S. plate of 2mm thick and the finish shall be powder coated in white finish UL Listed or FM approved complete as required.

Misc.civil works 14.14.3 : Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.250 mm dia

14.7 : Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required.

od97530/2022_2023 : Fire protection for service shafts: Providing and installing system of Fire Barrier mortar in service shaft with reinforcement bars across the shaft with minimum 2 hours fire rating when tested in accordance with BS 476 part 20 and UL 1479 for horizontal openings in fire rated floors or slabs . The mortar shall have a minimum hardened density of 0.8 g/cm3. The service lines could be of various types like electrical cables trays &amp; Cables, Pipe lines. The product shall bear the UL logo on the packing.

FIRE SIGNAGE od97513/2022_2023 : Providing and installing in position the following type of sign boards made out of 3mm thick .;Opaque.; PVC foam board with computer cut, PVC non-reflective self adhesive vinyl painted foam board, complete with mirror fasteners of following size:3 x 4;. It should contain the following matter .; FIRE ORDER.; . A) ALERT THE SECURITY AT SECURITY ROOM BY ACTUATING MANUAL CALL POINT LOCATED AT STRATEGIC LOCATIONS. B) EVACUATE THE OCCUPANTS BY USING FIRE EXITS AND EMERGENCY EXITS ONLY AND ASSEMBLE AT VARIOUS ASSEMBLY POITS. C) IF POSSIBLE TRY TO EXTINGUISH THE FIRE BY USING NEAREST / SUITABLE PORTABLE EXTINGUISHER OR WATER FROM NEAREST WET RISER. D) BE CALM AND DO NOT GIVE ANY ROOM FROM PANIC, WALK, DO NOT RUN. E) IF YOU ENCOUNTER SERIOUS DIFFICULTY IN EVACUATION, FLAT AND TRY TO ATTRACT ATTENTION OF RESCUE TEAM. ACTION BY SECURITY/RECEPTION UPON RECEIPT OF INFORMATION THROUGH FIRE ALARM ORFIRE DETECTORS OR BY USING PUBLIC ADDRESS SYSTEM.

od97524/2022_2023 : Providing and installing in position the following type of sign boards made out of 3mm thick .;Opaque.; PVC foam board with computer cut, PVC non-reflective self adhesive vinyl painted foam board, complete with mirror fasteners. Writings shall be as follows .;ACTION BY SECURITY/RECEPTION UPON RECEIPT OF INFORMATION THROUGH FIRE ALARM ORFIRE DETECTORS OR BY USING PUBLIC ADDRESS SYSTEM. A) ALERT THE OCCUPANTS BY USING PUBLIC ADDRESS SYSTEM. B) INFORM FIRE CONTROL THROUGH ANY ONE OF THE FOLLOWING PHONE NUMBERS: 101 / 2251780 / 2251781 / 2251782. C) REFER EVACUATION PLAN FROM EVACUATING STANDARD PEOPLE. D) GUIDE THE FIRE FORCE, ON THEIR ARRIVAL TO THE SEAT OF FIRE. E) IN CASE OF THE CASUALTIES, CALL AMBULANCE BY DIALLING NUMBER&help FIRE FIGHTING AGNECY,PHONE ;

od97525/2022_2023 : Providing and installing in position the following type of sign boards made out of 3mm thick .;Opaque.; PVC foam board with computer cut, PVC non-reflective self adhesive vinyl painted foam board, complete with mirror fasteners. Floor identification signage ( i.e., GROUND FLOOR &hellip;etc.) at each stair enclosure on every floor, indicating the floor number in words, lettering size shall be 7.5 cm with contrasting color from back ground. Size shall be 15cm x 60cm.

od97538/2022_2023 : Providing and installing in position the following type of sign boards made out of 3mm thick .;Opaque.; PVC foam board with computer cut, PVC non-reflective self adhesive vinyl painted foam board, complete with mirror fasteners. Signage with printed .;IN CASE OF FIRE, USE STAIRS UNLESS INSTRUCTED OTHERWISE.;DO NOT USE LIFT.; of 1.5cm height letters in red with white back ground. The size of the board shall be 25cm x 30 cm and shall be fixed at the height of 2 meters from finished floor near Manual call points.

od97545/2022_2023 : Supply installation of ceiling suspended Fire Exit light Signage Board with arrow sign in chain strings of Size: 6.;x12.;.

od97552/2022_2023 : Supply installation of fire extinguisher chart board of Size: 18.;x24.; material : 5 mm Sun Board Auto Glow explaining the different types of fire extinguishers that can be utilized on different classes of fire.

od97558/2022_2023 : Supply installation of fire extinguisher signage board of Size: 6.;x12.; material : 5 mm Sun Board Auto Glow to show the locations where fire extinguishers get affixed.

od97567/2022_2023 : Supply installation of Fire Evacuation Sign Board,size:A3,colour, material : Acrylic.

od97573/2022_2023 : Supply installation of safe assembly area board of Size: 9.;x18.; material : 5 mm Sun Board Auto Glow.

Civil items 2.10.1.2 : Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

2.13.1.2 : Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth up to 1.5 m including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth. including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m:Pipes, cables etc. exceeding 80m dia but not exceeding 300 mm dia

20 Passenger cum Bed Lifts od192094/2022_2023 : Supply, installation, testing &amp; commissioning of electric traction type elevator of following capacities and type suitable for operation on 415 V, 3 phase, 50 Hz AC supply, having AC variable voltage and variable frequency type traction control, machine room less, speed of 1.00 Mtr/sec, electromagnetic brake system, simple operations, operating control panel with luminous buttons, overload warning indicator, battery operated alarm bell, LED type emergency light, intercom suitable for hook up to EPABX, infrared ray sensing door protection for full height, reverse phase relay on controller, fireman& resque switch at ground floor, digital car positions indicator in car and at all positions indicator in car and at all floors with Up/DOWN direction, all signal fixtures in stainless stell faceplates, light fixtures, ventilation fan, etc complete with all accessories including automatic rescue device in the event of power failure etc., Complete with necessary scaffolding, electrical panel, logic control panel and shaft lighting etc required for the erection of the elevators as required.Machine Room Less Type with the traction motor placed on top of the hoistway and elevator shall be of gearless type (suitable for lift well size 3000mm (D)X 2400m(W)) complete as per technical specification, simplex full collective operation with/without attendant. Car/Hoistway Entrance, protected by stainless steel hairline doors and clear center /side opening min 1200mm wide X 2000mm height. 20 passengers (Minimum) capacity (minimum 1360 Kgs) Bed Lift , car size of 1300mm wide x2400mm deep x 2200mm Height Inside dimensions and entrance at front side on all the serving floors, provided with matt finish stainless steel panel on all four side and ceiling, stretcher protection on three sides complete as per specifications. Price shall include necessary liasioning works from all statutory departments.

OXYGEN SYSTEM od112994/2022_2023 : Supply,testing and commissioning of Automatic Oxygen Control Panel with minimum flow rate of 1500 LPM.Automatic changeover from Running Bank to Reserve Bank of cylinders and having non-halogenated polymer in the high pressure side of the primary regulators and 40 micron inlet filter.Fully complying with ISO 10524-2, ISO 7396-1:2007/HTM02-01 as per technical specifications.

od113007/2022_2023 : Supply, testing and commissioning of a high flow regulator with gauges and safety valves complete with all accessories etc. as required complete as per specification

od113017/2022_2023 : Supply,testing and commissioning of Oxygen Manifold - 2 banks x10 cylinders with NRV, Tail pipes and Middle frame, as per technical specifications.

od113025/2022_2023 : Supply,testing and commissioning of Cylinder Emergency Oxygen Manifold complete with tail pipe, NRV and Pressure Reducung System having nonhalogenated polymer materials in the high pressure side of the regulator - 2 Bank X2 Cylinders

NITROUS OXIDE SYSTEM od112987/2022_2023 : Supply,testing and commissioning of 1000 LPM fully automatic N2O control panel with automatic change over from runnig bank to reserve bank of cylinder complete set with inlet and outlet connectors for fully automatic control panel for both sides with brass hosing and suitable connectors.12; BSP (M) thread.

od112995/2022_2023 : Supply, testing and commissioning of Nitrous Oxide Manifold - 2 banks x 4 cylinders with NRV ,Tail pipes and middle frame as per technical specifications.

od113003/2022_2023 : Supply,testing and commissioning of Cylinder Emergency Nitrous oxide Manifold with tail pipe ,NRV and pressure regulator- 1 bank x 2 cylinders as per technical specifications.

CARBON DIOXIDE SYSTEM od112990/2022_2023 : Supply, testing and commissioning of semi automatic CO2 control panel complete set with inlet and outlet connectors for fully automatic control panel for both sides with brass housing and suitable connectors. &frac12&; BSP (M) thread.

od112996/2022_2023 : Supply, testing and commissioning of Cylinder CO2 Manifold - 1 bank x 2 cylinder with a high flow regulator with gauges and safety valves complete with all accessories etc. as required complete as per specification

VACUUM PLANT od112982/2022_2023 : Supply, testing and commissioning of Vacuum plant complete with 2 compressor vacuum pumps(10hp each) with Control panel for 2 no. vacuum pump (for cascading &amp;amp; duplex) along with provision for one future pump installation, each vacuum pump should have minimum free air aspirated of 1500 LPM at 450 mmHg, 1 vacuum receiver-2000 Litre, secretion trap, bacteria double filter, ball valves,2 NRV,Silencer(if required) etc.

od112997/2022_2023 : Supply, testing and commissioning of Master Plant Alarm Panel as per technical specifications.

od113004/2022_2023 : SITC of Combined Electrical Control panel with wiring for Air compressor &amp; vacuum Pump system as per technical specification.

od113013/2022_2023 : Supply, installation ,testing and commissioning of Duplex AGSS system with 630LPM capacity as per specification.

PIPELINE SYSTEM od112986/2022_2023 : Supply, installation testing and commissioning of Copper pipe Per Mtr. It must comply with EN 13348 as per technical specifications with fittings and fixing in / on walls, ceiling by using suitable supports. Painting, Marking color coding, direction of flow and identifications as per standards.Fittings End-feed type, made from the same grade of copper as the pipes, and in accordance with the requirements of BS- EN 1254-1: 1998 Part 1.Pipe clamps Shall be non-reactive to copper and be of non-ferrous or non-deteriorating plastic suitable for the diameter of the pipe. Pipeline supports Spacing not to exceed 1.5M, irrespective of the pipe diameter. 12mm OD X 1.0 mm thick.

od112998/2022_2023 : Supply, installation testing and commissioning of Copper pipe Per Mtr. It must comply with EN 13348 as per technical specifications with fittings and fixing in / on walls, ceiling by using suitable supports. Painting, Marking color coding, direction of flow and identifications as per standards.Fittings End-feed type, made from the same grade of copper as the pipes, and in accordance with the requirements of BS- EN 1254-1: 1998 Part 1.Pipe clamps Shall be non-reactive to copper and be of non-ferrous or non-deteriorating plastic suitable for the diameter of the pipe. Pipeline supports Spacing not to exceed 1.5M, irrespective of the pipe diameter. 15mm OD X 0.9 mm thick

od113006/2022_2023 : Supply, installation testing and commissioning of Copper pipe Per Mtr. It must comply with EN 13348 as per technical specifications with fittings and fixing in / on walls, ceiling by using suitable supports. Painting, Marking color coding, direction of flow and identifications as per standards.Fittings End-feed type, made from the same grade of copper as the pipes, and in accordance with the requirements of BS- EN 1254-1: 1998 Part 1.Pipe clamps Shall be non-reactive to copper and be of non-ferrous or non-deteriorating plastic suitable for the diameter of the pipe. Pipeline supports Spacing not to exceed 1.5M, irrespective of the pipe diameter. 22mm OD X 0.9 mm thick

od113019/2022_2023 : Supply, installation testing and commissioning of Copper pipe Per Mtr. It must comply with EN 13348 as per technical specifications with fittings and fixing in / on walls, ceiling by using suitable supports. Painting, Marking color coding, direction of flow and identifications as per standards.Fittings End-feed type, made from the same grade of copper as the pipes, and in accordance with the requirements of BS- EN 1254-1: 1998 Part 1.Pipe clamps Shall be non-reactive to copper and be of non-ferrous or non-deteriorating plastic suitable for the diameter of the pipe. Pipeline supports Spacing not to exceed 1.5M, irrespective of the pipe diameter. 28mm OD X 0.9 mm thick

od113020/2022_2023 : Supply, installation testing and commissioning of Copper pipe Per Mtr. It must comply with EN 13348 as per technical specifications with fittings and fixing in / on walls, ceiling by using suitable supports. Painting, Marking color coding, direction of flow and identifications as per standards.Fittings End-feed type, made from the same grade of copper as the pipes, and in accordance with the requirements of BS- EN 1254-1: 1998 Part 1.Pipe clamps Shall be non-reactive to copper and be of non-ferrous or non-deteriorating plastic suitable for the diameter of the pipe. Pipeline supports Spacing not to exceed 1.5M, irrespective of the pipe diameter. 35 mm OD X 1.2 mm thick

od113027/2022_2023 : Supply, installation testing and commissioning of Copper pipe Per Mtr. It must comply with EN 13348 as per technical specifications with fittings and fixing in / on walls, ceiling by using suitable supports. Painting, Marking color coding, direction of flow and identifications as per standards.Fittings End-feed type, made from the same grade of copper as the pipes, and in accordance with the requirements of BS- EN 1254-1: 1998 Part 1.Pipe clamps Shall be non-reactive to copper and be of non-ferrous or non-deteriorating plastic suitable for the diameter of the pipe. Pipeline supports Spacing not to exceed 1.5M, irrespective of the pipe diameter. 42mm OD X 1.2 mm thick

od113034/2022_2023 : Supply, installation testing and commissioning of Copper pipe Per Mtr. It must comply with EN 13348 as per technical specifications with fittings and fixing in / on walls, ceiling by using suitable supports. Painting, Marking color coding, direction of flow and identifications as per standards.Fittings End-feed type, made from the same grade of copper as the pipes, and in accordance with the requirements of BS- EN 1254-1: 1998 Part 1.Pipe clamps Shall be non-reactive to copper and be of non-ferrous or non-deteriorating plastic suitable for the diameter of the pipe. Pipeline supports Spacing not to exceed 1.5M, irrespective of the pipe diameter. 54 mm OD X 1.2 mm thick

od113038/2022_2023 : Supply,installation testing and commissioning of Copper pipe Per Mtr. It must comply with EN 13348 as per technical specifications with fittings and fixing in / on walls, ceiling by using suitable supports.Painting, Marking color coding,direction of flow and identifications as per standards.Fittings End-feed type, made from the same grade of copper as the pipes, and in accordance with the requirements of BS- EN 1254-1: 1998 Part 1.Pipe clamps Shall be non-reactive to copper and be of non-ferrous or non-deteriorating plastic suitable for the diameter of the pipe.Pipeline supports Spacing not to exceed 1.5M, irrespective of the pipe diameter. 76 mm OD X 1.5 mm thick

MEDICAL GAS OUTLET od112985/2022_2023 : Supply, Installation , testing and commissioning of BS type Gas Outlets with double locking, meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications -O2 Outlets with Probes

od112999/2022_2023 : Supply, Installation , testing and commissioning of BS type Gas Outlets with double locking, meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications -N2O Outlets with Probes

od113008/2022_2023 : Supply, Installation , testing and commissioning of BS type Gas Outlets with double locking, meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications -Air (4 bar) Outlets with Probes

od113014/2022_2023 : Supply, Installation , testing and commissioning of BS type Gas Outlets with double locking, meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications - Air (7 bar) Outlets with Probes

od113023/2022_2023 : Supply, Installation , testing and commissioning of BS type Gas Outlets with double locking, meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications - Vacuum Outlets with Probes

od113031/2022_2023 : Supply, Installation , testing and commissioning of BS type Gas Outlets with double locking, meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications - CO2 Outlets with Probes

od113036/2022_2023 : Supply, Installation , testing and commissioning of BS type Gas Outlets with double locking, meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications - AGSS with Probes

NIST CONNECTOR,NUT AND NIPPLE CONNECTORS od112984/2022_2023 : Supply, installation testing and commissioning of NIST Connectors one set each -3/8.; O2

od113000/2022_2023 : Supply, installation testing and commissioning of NIST Connectors one set each -3/8; VACUUM

od113005/2022_2023 : Supply, installation testing and commissioning of NIST Connectors one set each -3/8.; MA4

od113015/2022_2023 : Supply, installation testing and commissioning of NIST Connectors one set each -3/8.; SA7

od113026/2022_2023 : Supply, installation testing and commissioning of NIST Connectors one set each -3/8.; CO2

od113028/2022_2023 : Supply, installation testing and commissioning of NIST Connectors one set each -3/8.; N2O

od113035/2022_2023 : Supply, installation testing and commissioning of Nut and nipple Connectors for pipeline and outlets - 3/8

od113039/2022_2023 : Supply, installation testing and commissioning of Nut and nipple Connectors for pipeline and outlets - 1/2 and

AREA VALVE SERVICE UNIT WITH ALARM SYSTEM od112989/2022_2023 : Supply, Installation, testing and commissioning of Area Valve Service Unit with gauges and other accessories + Alarm Units microprocessor controlled alarm with digital display of gas pressure, High to low setting of audio -visual alarm fully complying with ISO 7396-1:2007 , as per technical Specifications. 2 gas - 1 O2, 1 Vacuum.

od112993/2022_2023 : Supply, Installation, testing and commissioning of Area Valve Service Unit with gauges and other accessories + Alarm Units microprocessor controlled alarm with digital display of gas pressure, High to low setting of audio -visual alarm fully complying with ISO 7396-1:2007 , as per technical Specifications. 3 gas - 1 O2, 1 Medical Air &amp; 1 Vacuum

od113022/2022_2023 : Supply, Installation, testing and commissioning of Area Valve Service Unit with gauges and other accessories + Alarm Units microprocessor controlled alarm with digital display of gas pressure, High to low setting of audio -visual alarm fully complying with ISO 7396-1:2007 , as per technical Specifications. 6 gas- 1 O2, 1 Medical Air,1 N2O, 1 CO2, 1 Surgical air , &amp; 1 vacuum

ISOLATION BALL VALVE od112991/2022_2023 : Supply, installation, testing and commissioning of Isolation Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications: -15 mm

od113001/2022_2023 : Supply, installation, testing and commissioning of Isolation Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications: -22 mm

od113010/2022_2023 : Supply, installation, testing and commissioning of Isolation Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications: -28 mm

od113012/2022_2023 : Supply, installation, testing and commissioning of Isolation Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications: -35 mm

od113024/2022_2023 : Supply, installation, testing and commissioning of Isolation Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications: -42 mm

od113029/2022_2023 : Supply, installation, testing and commissioning of Isolation Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications: -54 mm

od113032/2022_2023 : Supply, installation, testing and commissioning of Isolation Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications: -76 mm

MISCELLANEOUS od112988/2022_2023 : Supply, testing and commissioning of D type Oxygen Gas Cylinder as per technical specification.

od113002/2022_2023 : Supply, testing and commissioning of D type Nitrous Oxide Gas Cylinder as per technical specification.

od113009/2022_2023 : Supply, testing and commissioning of D type CO2 Gas Cylinder as per technical specification.

od69297/2023_2024 : Supply and installation of Bed Head 5ft(Horizontal) unit made out of High sbength extruded Aluminum Panel of minimum 2.5 mm thickness with powder coated to make it aesthetically appealing and long lasting, the panel should be divided into different sections to segregate power, data and medical gas chamber suitable for accommodating following utilities - Oxygen, Vacuum, Medical Air, Nurse call switch &mdash; 1, spare probe, 2 no 5 /15A combined socket with switch outlet &mdash; 2 set, provision RJ-45 socket/ Ethernet, shall have monitor holder and equipped with two side rail system to hold different associated accessories like vaccine basket, Holder for vacuum collection jar, examination lamp, IV pole, etc. and all necessary mechanical supports for complete installation as instructed and directed by engineer in- charge.-Bed head panel as above with 5 Gas outlet

od69298/2023_2024 : Supply and installation of Bed Head 5ft(Horizontal) unit made out of High sbength extruded Aluminum Panel of minimum 2.5 mm thickness with powder coated to make it aesthetically appealing and long lasting, the panel should be divided into different sections to segregate power, data and medical gas chamber suitable for accommodating following utilities - Oxygen, Vacuum, Medical Air, Nurse call switch &mdash; 1, spare probe, 2 no 5 /15A combined socket with switch outlet &mdash; 2 set, provision RJ-45 socket/ Ethernet, shall have monitor holder and equipped with two side rail system to hold different associated accessories like vaccine basket, Holder for vacuum collection jar, examination lamp, IV pole, etc. and all necessary mechanical supports for complete installation as instructed and directed by engineer in- charge. Bed head panel as above with 2 Gas outlet

od113030/2022_2023 : Supply Installation of BPC Oxygen Flow meter with humidifier &amp; 0 -15 lpm range ,bottle polycarbonate ,autoclavable complying with HTM 02-01 as per technical specification.

od113033/2022_2023 : Supply Installation of Ward vacuum unit with 600 ml polycarbonate autoclavable collection jar with vaccum gauge,suction tube,over flow protection with HTM 02-01 as per technical specification.

od113040/2022_2023 : Supply Installation of Theatre Vacuum unit with Regulator and trolly ,polycarbonate collection jars 2 having 2000 ml capacity each with HTM 02-01 as per technical specifications.

od113041/2022_2023 : Providing and fixing conversion Kit with standard index adaptor with diameter index safety plugs -Oxygen Set

od113043/2022_2023 : Providing and fixing conversion Kit with standard index adaptor with diameter index safety plugs-Nitrous oxide set

od113044/2022_2023 : Supply,Installation,testing and commissioning of Colour coded High Pressure Antistatic Hose with color coded.

od113045/2022_2023 : Supply,Installation,testing and commissioning of Colour coded Low Pressure Antistatic Hose with color coded.

SOLAR PV SYSTEM

od168509/2021_2022 : Supply, Installation, Testing and Commissioning of 60 kWp on-grid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono /Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium /GI structure of suitable strength with following components complete as required:-;a) Solar Photovoltaic Module of capacity 330Wp or above, manufactured in India, conforming to IS14286 / IEC 61215, IS / IEC 61730 -Part-1, IS / IEC 61730-Part 2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years.b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400VAC, three-phase, 4 wire, 50Hz +/- 2.5Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 20 to 45 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency.c) Data Monitoring System complete with accessories. d) Fixing of Array junction box &amp; Main junction box with IP65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs, and other accessories, etc. as required:e) Lightning and surge voltage protection.f) Connections &amp; Interconnections by supplying &amp; fixing required size XLPE insulated copper conductor 1.1kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying &amp; fixing of necessary channel/conduit lugs and other accessories, :g) AC & DC distribution board with necesssary MCB,surge protector,distribution panel ,h) 4 nos Earth electrodes with connecting earthing leads etc. as required.

THE URALUNGAL LABOUR CONTRACT CO-OPERATIVE SOCIETY

THE URALUNGAL LABOUR CONTRACT CO-OPERATIVE SOCIETY

THE URALUNGAL LABOUR CONTRACT CO-OPERATIVE SOCIETY