Construction of Indoor Auditorium building at Kullu District Kullu SH Providing microphone and cables system therein

Amount

SITC of DMX Snake cable for left side of stage 16 Pair Digital Snake Cable – 24 AWG (19/0.12mm) x 2 core ABC copper conductor, PE insulated, core twisted in circular form, Mylar Polyester Taped, ABC Spiral shielded + Aluminum foil shielded, PVC Inner Sheathed, Matt Finish High Flex Special PVC Overall Sheathed Snake Cable,with pvc conduit pipe install Make-falcon,krystal

SITC of DMX Snake cable for right side of stage 16 Pair Digital Snake Cable – 24 AWG (19/0.12mm) x 2 core ABC copper conductor, PE insulated, core twisted in circular form, Mylar Polyester Taped, ABC Spiral shielded + Aluminum foil shielded, PVC Inner Sheathed, Matt Finish High Flex Special PVC Overall Sheathed Snake Cable,with pvc conduit pipe install Make-falcon,krystal

SITC of stage XLR box connection of one side of the snake wire 12 in /4 out on stage.

SITC of Foot Mic/Boundary microphone The low-profile design assures inconspicuous appearance for surface-mount use in school, government, house of worship and other installed applications. Designed for sound reinforcement, broadcasting and recording applications,. Element -Fixed-charge back plate, permanently polarized condenser Polar Pattern- Half-cardioid (cardioid in hemisphere above mounting surface) Frequency Response -70-14,000 Hz Open Circuit Sensitivity -38 dB (12.5 mV) re 1V at 1 Pa Maximum Input Sound Level- 134 dB SPL, 1 kHz at 1% T.H.D. Dynamic Range- 105 dB, 1 kHz at Max SPL Signal-to-Noise Ratio- 65 dB, 1 kHz at 1 Pa Phantom Power Requirements- 9-52V DC, 2 mA typical Output Connector 3-pin XLRM-type on cable Make-audio technica,shure,akg

SITC of boom mic Designed for use in broadcasting, film/TV production and theater sound reinforcement applications Direct-coupled, balanced output ensures a clean signal even in high-output conditions Innovative acoustic design provides same directivity as mics up to 50% longer Switchable 80 Hz hi-pass filter & 10 dB pad Rugged housing made of lightweight structural-grade aluminum alloy RoHS-compliant – free from all substances specified in the EU directive on the reduction of hazardous substances FREQUENCY RESPONSE- 20-20,000 Hz IMPEDANCE -50 ohms ELEMENT- Externally polarized (DC bias) capacitor POLAR PATTERN- Line + gradient LOW FREQUENCY ROLL-OFF 80 Hz, 18 dB/octave OPEN CIRCUIT SENSITIVITY -29 dB (35.5 mV) re 1V at 1 P OUTPUT CONNECTOR Integral 3-pin XLRM-type PHANTOM POWER REQUIREMENTS -48V DC, 4.8 mA typical MAXIMUM INPUT SOUND LEVEL -141 dB SPL, 1 kHz at 1% T.H.D.; 151 dB SPL, with 10 dB pad Make-audio technica,shure,akg

SITC of Mic Stand • Short microphone boom stand • Ergonomic knob for a secure fastening • Joint, clutch, counterweight and base made of loaded nylon • Non-slip rubber feet • Joint with picks space and knob made of loaded nylon • Ergonomic clutch

SITC of XLR to mono jack Cable xlr male to mono cable of length 10 mtr Make-Neutric,krystal

SITC of XLR Connectors Supply of Solid 3 pole Male/female cable XLR Connectors with with locking ring and coaxial shell. (pairs). Make: Neutrik/Amphenol/Krystal

SITC of DMX Cable DMX Cable with 8 AWG ‐24/0.20mm x 2 core ATC Copper Conductor, PVC Insulated, 90 % ATC Copper Braid Shielded, PVC Sheathed control Cable. (in metres)with pvc pipe installtion.Make: Falkon/Krystal/Belden

SITC of power cable Hi-flex Lighting Cable – 4 Sqmm (128/0.20mm) x 3 core cable ABC copper conductor PVC insulated , core twisted, outer jacketed with Highly Flexible Matt Finish PVC Sheath.with pvc pipe installtion.

SITC of XLR Cable xlr male to xlr female cable of length 10 mtr Make-Neutric,krystal

MATRIX INTEGRATIONS