SMCH/ PICU-42 Construction of 30 PICU beds and 12 HDU Beds at First floor of South Block and 16 steps down Beds at 2nd floor of North Block and Other ancillary works at Silchar Medical College and Hospital, Silchar

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emul sion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

"Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : " 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

"Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : " 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

"Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level." Thermo-Mechanically Treated bars of grade Fe-500D or more

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

"Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: " 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

"Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : " 300x16 mm

"Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : " 300x10 mm

"Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete. 25 mm thick.

"Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Electric resistance or induction butt welded tubes

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge.

62 mm thick cement concrete flooring with concrete hardener topping,under layer 50 mm thick cement concrete 1:2:4

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement 18 mm thick

Providing and laying machine cut, mirror polished, Italian Marble stoneflooring laid in required pattern in linear portion of the building all complete 11.51.1 18 mm thick Italian Marble stone slab, Perlato, Rosso verona

"Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intesuitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting " 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

Providing corrugated G.S. sheet roofing including vertical / curvedsurface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet 12.1.3 0.63 mm thick with zinc coating not less than 275 gm/ m

"Providing ridges or hips of width 60 cm overall width plain G.S. sheetfixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I.limpet and bitumen washers complete 12.4.2 0.63 mm thick with zinc coating not less than 275 gm/m²" Ridges plain (500 - 600mm)

CEMENT PLASTER (IN FINE SAND) 15 mm cement plaster on rough side of single or half brick wall of mix 1:4 (1 cement: 4 fine sand)

Applying one coat of water thinnable cement primer of approved brand etc. 13.43.1 Water thinnable cement primer

Finishing walls with textured exterior paint of required shade etc 13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm)

Applying priming coat With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

"Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : " 13.60.1 Two or more coats on new work

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material etc.

Dismantling tile work in floors and roofs laid in cement mortar includingstacking material within 50 metres lead. 15.23.2 For thickness of tiles above 25 mm and up to 40 mm

Dismantling roofing including ridges, hips, valleys and gutters etc.,and stacking the material within 50 metres lead of: 15.28.1 G.S. Sheet

Demolishing R.C.C. work manually/ by mechanical means includingstacking of steel bars and disposal of unserviceable material within50 metres lead as per direction of Engineer - in- charge

Providing and fixing PTMT liquid soap container 109 mm wide, 125mm high and 112 mm distance from wall of standard shape etc.

Providing and fixing PTMT towel rail complete with brackets fixed towooden cleats with CP brass screws with concealed fittingsarrangement of approved quality and colour. 17.73.2 600 mm long towel rail with total length of 645 mm, width 78mm etc.

Providing and fixing C.P. brass bib cock of approved quality conforming 18.49.1 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standarddesign and of approved make conforming to IS:8931. 18.52.1 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyserpoints of approved quality conforming to IS:8931 18.53.1 15mm nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc External work 80 mm dia nominal bore

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing 12 mm thick prelaminated particle board flatpressed three layer or graded wood particle board conforming to IS: 21.2.2 Pre-laminated particle board with decorative lamination of both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item) With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Dismantling old plaster or skirting raking out joints and cleaning thesurface for plaster including disposal of rubbish to the dumping ground within 50m leads

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge(15.7.4) - In cement mortar

Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll 9.147E.1-Two track

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ±

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying. (a),(b),(c),(d)

Providing and applying of swellable type water stop tape, 19mm x 25mm thick in linear meter (expansive nature) for construction joints treatment of RCC structure such as raft slab, retaining walls, water

Providing and laying vitrified floor tiles in different sizes (thickness to bespecified by the manufacturer) with water absorption less than 0.08% 11.41.2 Size of Tile 600x600 mm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey,

Providing and fixing factory made door frame (single rebate) made out ofsingle piece extruded solid PVC foam profile with homogenous finecellular structure having smooth outer integral skin having 62 mm width

Providing and fixing factory made 30 mm thick door shutter made ofsolid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall(9.124.1) - Non-decorative finish

Dry brick pitching half brick thick in drains including supply of bricksand preparing the surface complete 16.12.1 With common burnt clay F.P.S. (non modular) bricks of

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled 17.2.2 W.C. pan with ISI marked black solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including 17.7.1 White Vitreous China Wash basin size 630x450 mm with

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings

Providing and fixing P.V.C. low level flushing cistern with manuallycontrolled device (handle lever) conforming to IS : 7231, with all fittings 17.18.1 10 litre capacity - White

Providing and fixing P.V.C. waste pipe for sink or wash basin includingP.V.C. waste fittings complete 17.28.2 Flexible pipe 17.28.2.1 32 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801 UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold 18.6.9 PN - 10 Pipe, 110 mm OD (SDR-11)

18.6.6 PN - 10 Pipe, 63 mm OD (SDR-11

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing 18.8.1 15 mm nominal outer dia Pipes

18.8.2 20 mm nominal outer dia Pipes

18.8.3 25 mm nominal outer dia Pipes

Supplying, fitting and fixing MAC blinds horizontal and vertical complete as specified and directed by the department at all levels. (A) Vertical blinds (a) Regular iv) 50 mm

Supply, Installation, Fixing of CARBON DIOXIDE Fire Extinguisher confirming to IS: 2878 with ISI Mark.(4.5 LITERS) BRAND : FIRESTOP / FIREND / FIRE SHIELD / GETECH/ MINIMAX

Supply and fixing of PVC single layer homogenous flooring 2.0mm thick as per EN 649 having heat welded scams for join free installation, with corner coving, for heavy duty aplication as per EN 685, suitable for castor wheels furniture movement, antimicrobial and anti fungal, chemical resitant and antistatic behaviour, duly pasted on base floor using manufactures recomended ashesive and good installation practice complete in all respect as directed by the engineer

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (1.10.3) Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (1.14.1) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

(1.14.2) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

(1.14.3) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

(1.14.4) 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

(1.14.9) 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

(1.14.10) 4 X 10 sq. mm + 2 X 6 sq. mm earth wire

(1.14.11) 4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but Excluding modular plate etc. as required. (1.24.1) 5/6 A switch

(1.24.3) 15/16 A switch

(1.24.4) 3 pin 5/6 A socket outlet

(1.24.5) 6 pin 15/16 A socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including Connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. (1.27.3) 4 Module (125mmX75mm)

(1.27.4) 6 Module (200mmX75mm)

(1.27.6) 12 Module (200mmX150mm)

Erection of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS lamps per fitting, complete with all accessories including connection etc. as required.

Supplying and fixing PVC batten/ angle holder including Connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. (1.50.1) Upto 450 mm sweep

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. (7.1.1)Upto 35 sq. mm

(7.1.3) Above 95 sq. mm and upto 185 sq. mm

(7.1.4) Above 185 sq. mm and upto 400 sq. mm

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. (2.2.13) 100 A,30KA,FPMCCB

(2.2.14) 125 A,36KA,FPMCCB

(2.2.16) 250 A,36KA,FPMCCB

(2.2.18) 400 A,50KA,FPMCCB

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (2.3.1) 6 way , Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (2.4.2) 6 way (4 + 18), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (2.10.1) Single pole

(2.10.3) Double pole

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and Commissioning etc. as required. (2.13.3) 100 A

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL) (17.1.9) Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 4 Zone

FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL) (17.1.2) Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.

FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL) (17.1.3) Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL) (17.1.6) Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required

CABLING & WIRING (17.5.3.4) Speaker cable Four pair, 2-core, 1.5 sqmm

CABLING & WIRING (17.5.4) Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

Supplying with installation, testing & commissioning of Hi-wall 3-star rating non-duct able split type Air-Conditioner of the following capacity with cordless remote control with copper pipe and electrical connection cable etc. 2ton capacity . (Code No- 4502740 3-star, Delux, Voltas SAC 243Volt DZV(R32) Volage make.

Supplying with fitting and fixing of voltage stabilizer (Denen) of the following specification including making necessary connection. 5KVA (Rahino-59) 5KVA, 90V

Supplying including fitting fixing of single phase power & motor starter code no- 20405, 25A starter switch HSN-8536 (Anchor, Panasonic) make Roma Classic.

Supplying with installation of 400Amp indoor type floor/wall mounted distribution control Panel Board made with 1.6mm CRCA Sheet including aluminum bus-bar, copper internal wiring, painting etc. as reqd.

Supplying with installation of 250Amp indoor type floor/wall mounted distribution control Panel Board made with 1.6mm CRCA Sheet including aluminum bus-bar, copper internal wiring, painting etc. as reqd.

Supplying of A/C Ceiling fan of the following sweep model etc. without regulator Eco Ceiling fan 1200mm W/O Reg. white.

Supplying of 300mm sweep Domestic exhaust fan (.300mm spring Air.

Supplying of 450mm industrial heavy duty exhaust fan 960rpm.

Supplying of following size PVC/XLPE insulated and PVC sheathed 1.1KV grade solid Aluminum conductor up to 10sq. balance stranded conductor XLPE insulated cores laid up, PVC tape inner sheathed Armor galvanized steel strip extruded PVC type ST2 sheathed 650/1100V grade as per IS-7908(part-I) 1999 amounted U.G. cable. (Havells,R.R. Kable make). 35sqmm 3 ½ core

Supplying of following size PVC/XLPE insulated and PVC sheathed 1.1KV grade solid Aluminum conductor upto 10sq. balance standard conductor, XLPE insulated cores laid up, PVC tape inner sheathed Armoured ( galvanized wire for cable upto 2x10sqmm, 3x10sqmm, 4x6sqmm & balance all galvanized steel strip) extruded PVC type ST2 sheathed 650/1100V grade as per IS-7908(part-I) 1988 armouned U.G. cable. (Havells make). 120sqmm 3 ½ core

Supplying of following size PVC/XLPE insulated and PVC sheathed 1.1KV grade solid Aluminum conductor upto 10sq. balance standard conductor, XLPE insulated cores laid up, PVC tape inner sheathed Armoured ( galvanized wire for cable upto 2x10sqmm, 3x10sqmm, 4x6sqmm & balance all galvanized steel strip) extruded PVC type ST2 sheathed 650/1100V grade as per IS-7908(part-I) 1988 armouned U.G. cable. (Havells make). 150sqmm 3 ½ core

Supplying of following size PVC/XLPE insulated and PVC sheathed 1.1KV grade solid Aluminum conductor upto 10sq. balance standard conductor, XLPE insulated cores laid up, PVC tape inner sheathed Armoured ( galvanized wire for cable upto 2x10sqmm, 3x10sqmm, 4x6sqmm & balance all galvanized steel strip) extruded PVC type ST2 sheathed 650/1100V grade as per IS-7908(part-I) 1988 armouned U.G. cable. (Havells make). 240sqmm 3 ½ core

Supplying of following size PVC/XLPE insulated and PVC sheathed 1.1KV grade solid Aluminum conductor upto 10sq. balance standard conductor, XLPE insulated cores laid up, PVC tape inner sheathed Armoured ( galvanized wire for cable upto 2x10sqmm, 3x10sqmm, 4x6sqmm & balance all galvanized steel strip) extruded PVC type ST2 sheathed 650/1100V grade as per IS-7908(part-I) 1988 armouned U.G. cable. (Havells make). 300sqmm 3 ½ core

Supplying of 100mm dia G.I. pipe (light class).

Supply of L.T. control cable (copper conductor) side copper conductor upto 6sqmm & balance standard copper, XLPE insulated, cores laid up PVC innersheated armored (galvanized wire for 10x2.5sqmm galvanized steel strip) Extruded PVC type ST2 sheated 650/1100volts grade(Havells make) 2.5sqmm 10-core armored cable.

Supplying high efficiency recess mounted white powder coated CRCA housing with full mounted acrylic diffuser (2ftx2ft) 125Lm/W Code No- LVLTUISO36XC 36watt. (Jaguar make).

Supplying with fitting & fixing of LED batten tube light- 20watt 4th length including connection etc. (Anchor, Panasonic or equivalent make).

Supplying with fitting fixing of 7watt LED bulb.(ANCHOR/PANASONIC).

Payment to be made to APDCL for load security & fixrd charge etc.(As per APDCL norms) Considering 300Kw load.

MEDICAL OXYGEN SYSTEM Supply, Installation, Testing & Commissioning of Oxygen manifold extendable type complete with middle frame with chain for individual cylinder (bulk cylinder D type) along with Non-Return valves for every cylinder and high pressure annealed copper tail pipes with 1 end having brass adaptor and other end suitable for manifold non return valves and manifold will have 1 brass non return valves for individual oxygen cylinder, middle frame with circumferential M.S. Flat duly powder coated all as specified and as directed. Conformng to 3 digit CE mark with ISO 9001-2015 certified organizaion. VII) 8 + 8

Supply, Installation, Testing & Commissioning of Fully Automatic Digital Gas Control Panel for O2. Features:- i) The control panel cover is made using high quality M.S. Duly powder coated. ii) The supply of Gas does not depend on electricity. iii) Display is provided with built-in led to indicate high, normal and low line pressure. iv) Panel cover is fitted with lock to prevent unauthorized access, and can be swing open for maintenance. v) It includes pressure gauge (63mm) that indicated the gas pressure of each header and pipe line distribution pressure. vi) Capable to supply a distribution flow rate in excess of 2500 LPM. vii) Manufactured by CE certified/ ISO 9001-2008 Organization. viii) Easy usage and maintenance.

Supply, Installation, Testing & Commissioning of AMICO type Terminal Units with Double Lock Gas outlets for Oxygen/Vacuum/Air/N20 with probes/Adaptors Manufactured CE certifie/(Oxygen Gas Outlets) ISO certified Organization.

MEDICAL OXYGEN(02) SYSTEM Supply, Installation, Testing & Commissioning of Oxygen Flow meter, made with chrome plated brass body. Graduated flow tube and cover made of polycarbonate unbreakable. Adjustable flow by needle valve knowb with micrometrical regulation. Humidifier bottle is made of unbreakable polycarbonate material and is autoclavable.

Supply, Installation, Testing & Commissioning of Low Pressure Tubing Flexible having antistatic Core as per ISO standards with proper colour coded for O2, N2O, Compressed Air and Vacuum complete all as specified and directed

02 Ventilator probe

MEDICAL AIR SYSTEM(DUPLEX) Supply, Installation, Testing & Commissioning of INGERSOLL RAND/ ANESTIWATA MOTHERSON/ FS CURTIS CE marked oil free high pressure Air Compressor machine 3 Face, Duplex,Durable cast - iron with two intermediate duty applications. iv) With Dual 15HP motor

Supply,Installation,Testing & commissioning of 1000 Ltr Air Receiver Tank, 10 gauge thickness with safety valve

Supply,Installation,Testing & commissioning of Air drye (100 CFM)

Supply,Installation,Testing & commissioning of 3 stage Bacterial Filter Assy.

Supply, Installation, Testing & Commissioning of pressure reducing system with two nos pressure regulator

MEDICAL VACUUM SYSTEM Supply, Installation, Testing & Commissioning of INGERSOLL RAND/ ANESTIWATA MOTHERSON CE marked vacuum Pump with accessories, base mounting,Capacity:10 HP Duplex 10HP each double stage Vacuum pump including necessary Vacuum Acessories Like silencer,Receiver Tank(1000 Ltr with 10 gauge wall thickness) & vacuum Bacteria Filter

MEDICAL OXYGEN(O2) SYSTEM Supply, Installation, Testing & Commissioning of Ward Vacuum Unit with Regulator alongwith vacuum gauge, collection jar of 600ml capacity reusable plastic collection bottle with overflow safety tap wall mounted type with bracket complete all as specified and as directed.

Supply, Installation, Testing & Commissioning of Oxygen flow meter made with crome plated Brass body(IOX 14 Type)

(a)Supply, Installation, Testing & Commissioning of horizontal Bed Head pannel 5 ft long CE market Excluded pannel, powder coated along with accessories like IV hook (02-2 Nos, Vacuum-1 No) utility BP Basket, Monitor Tray, Allum. Clamp for ward vaccuum unit LED Examination light and anti bacterial switch & socket 3 Nos)

Supply, Installation, Testing & Commissioning of Copper pipes solid drawn, seamless, de-oxidized non- arsenical half hard, tempered and de- greased copper pipe conforming to latest BSEN 13348:2001 and manufactured as per BS : 2871,1971 part 1 Table X ( or as per EN1057) all copper pipes will be de greased & delivered copped at both ends.The pipes will be accompanied with manufactureers LLOYD test certificate i) 12mm OD x 0.7mm Thick

ii) 15mm OD x 0.9mm Thick

iii) 22mm OD x 0.9mm Thick

iv) 28mm OD x 0.9mm Thick

v) 42mm OD x 1.2mm Thick

vi) 54mm OD x 1.2mm Thick

Supply, Installation, Testing & Commissioning of Zonal Valve Box, are fully designed to suit multiple operational and requirement and ensure considering space for mounting. The configurations are Valve Boxes are described.:- i) 3 Gas Services- O2, Vacuum, 4 bar Air

ii) 5 Gas Services- O2, Vacuum, 4 bar Air, N20

Supply, Installation, Testing & Commissioning of Area Line Pressure Alarm with displays for various faults indications and capable of monitoring maximum 5 medical gas service by means of pressure switches etc with audible warning with automatic reedit when the gas service returns to normal as per standard specifications all as specified and as directed for the following Area Line Pressure Alarm:- ii) 3 Gas Line Pressure Alarm

Supply, Installation, Testing & Commissioning of Isolation Valves with brass body with nickel plate valves operating handle suitable for 15mm OD copper pipe to 28 mm OD copper pipes with brass adapter as per standard specifications all as specified and as directed for the following Isolation Valves:- 12mm OD PICU - 8 Nos HDU- 4 Nos STEPDOWN - .6 Nos

15mm OD PICU - 17 Nos HDU- 10 Nos STEPDOWN - .12 Nos

22mm OD PICU - 10 Nos HDU- 6 Nos STEPDOWN - .8 Nos

28mm OD PICU - 5 Nos HDU- 2 Nos STEPDOWN - .4 Nos

42mm OD PICU - 14 Nos HDU- 8 Nos STEPDOWN - .10 Nos

54mm OD PICU - 2 Nos HDU- 2 Nos

UCN CONSTRUCTION COMPANY PRIVATE LIMITED

M/s Sanwarmal Khetawat