SPECIAL REPAIR TO BLDG NO T-68, T-70 AND T-84 (OTM ACCN) AT RAJOURI LINE AND SPECIAL REPAIR TO DRAINAGE NO T-126 AT RAIPUR LINES IN DAMANA UNDER GE JAMMU

Amount

B/R Portion:- Taking down chowkhats or frames with shutter without taking off shutter from the frame not exceeding 1.5 Sqm each including cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and as directed.

Taking down chowkhats or frames with shutter without taking off shutter from the frame exceeding 1.5 Sqm but not exceeding 4 Sqm each including cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and as directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm complete all as specified and as directed.

Refixing the shutters exceeding 1 Sqm and not exceeding 2 Sqm each in same opening complete all as specified and as directed.

Dismantling asbestos cement (corrugated or semicorrugated etc) sheets in roof covering complete all as specified and as directed.

Dismantling timber scantling 40 sqcm and over in section framed work of any description complete all as specified and as directed.

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches pillars etc and removing unserviceable material exceeding 100 mtr complete all as specified and as directed.

Demoltion of cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removing unserviceable material exceeding 100 mtr complete all as specified and as directed.

Dismantling boarding any description fixed in any position with nail complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including racking out joints hacking for key scrubbing with water etc complete all as specified and as directed.

Hacking out old broken glass of any thickness, size, quality or description from the wooden frames glazing with putty or fixed with wooden beads complete all as specified and as directed.

M&L brick work with sub class 'B' brick straight or curved on plan exceeding 6m mean radius built in CM 1:6 complete all as specified and as directed.

Description same as per Ser Item No 12.00 here-in-before but except bricks complete all as specified and as directed.

M&L for pressed steel frames for door (factory made) out of 1.25mm thick black MS sheet, with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc. complete size of frame 125 X 60mm including bottom of each chowkhat to be welded with 2 No's 25 X 25 X 3mm thick flat iron projecting 10cm on ither side and back fill to chowkhats with PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) including one shop coat of red oxide primer complete all as specified and as directed.

S&F for 35mm thick 2nd class hard wood plain framed, panelled shutter (two panel) of factory made with lock rail and panel of 12mm thick veneered particle board with commercial veneering on both faces including wooden beads on both sides, one coat of pink primer. The size of rail and stile as per IS : 1003 (Part - I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F for 35mm thick 2nd class hard wood factory made glazed and Skelton shutters open rebated and prepared to receive glass/wire gauge etc. without sash bar but with lock rail edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass / wire mesh etc sizes of member as per clause 8.20(a) of SSR Part - I for door shutter complete all as specified and as directed.

S&F Aluminium handle cast type, anodised size 150mm long, 'D' type complete all as specified and as directed.

S&F Aluminium anodised, barrel tower bolts with bright bolt and fixed 200mm complete all as specified and as directed.

S&F 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F box type steel windows / Ventilator (factory made) outer frame made out ERW tube 'P' section 65 X 45 X 25 mm and shutter of ERW tube 'P' section 50mm X 35mm X 20mm openable (double shutter) with glazed shutter on external side and gauzed shutter on internal side including steel pintel hinges steel handle 100mm long mild steel tower bolt 02 No's on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler / AC window complete all as specified and as directed and shown on Drgs No CEPZTD-324/07 Sh 1/3 to 3/3. Note: - The quoted rates shall also include: - (i) One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrete surface. (ii) 4 No's MS steel lugs made of 20 X 5mm iron flat 200mm long. (iii) 10mm Sq Bar grill / guard bar design as per drawing. (iv) PCC block for embedding lugs.

M&L for PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed. Note: - Form work required for these items included in the unit rate of this item.

S&F 3mm thick sheet glass ordinary quality glazing with steel pins, oil putty to steel windows and beads, nails etc to wooden surfaces as in square exceeding 0.50 Sqm in each pane complete all as specified and as directed.

S&F in repair Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws and washers complete all as specified and as directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws and washers complete all as specified and as directed.

M&L for rendering 10mm thick cement plaster in cement mortar (1:6) on other than fair faces of brick work or concrete surfaces of walls and to be finished even and smooth without using extra cement complete all as specified and as directed. (including all necessary scaffolding, lifting arrangement).

M&L for rendering 10mm thick cement plaster in cement mortar (1:4) on fair faces of brick work or concrete surfaces of walls and to be finished even and smooth without using extra cement complete all as specified and as directed. (including all necessary scaffolding, lifting arrangement).

M&L for preparation of new wood or wood based surface and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M&L for two coats of oil bound distemper of wall to newly plastered surfaces including preparation of surfaces with wall putty and cement primer complete all as specified and as directed.

M&L for one coat of oil bound distemper to old treated surfaces including preparation of surfaces with wall putty and cement primer complete all as specified and as directed.

S&F 4mm thick of size 605 X 605mm, white pre-premiered, self embossed, Reinforced Designer Board for false ceiling conforming to IS-14862 and ISO-8336:1993, as per specification under mentioned: - (i) GI section frame work (powder coated) for white, pre-premiered, self embossed, reinforced designer board consisting of perimeter wall angle 19mm X 19mm X 0.45mm, cross 'Tee' 28.6mm (web) X 24mm flange, 0.33mm thick, wall angle screwed fixed to brick wall / partition wall / concrete / RCC with the help of nylon sleeves and screws @ 610mm C/C, then suspending GI main 'Tee' in both directions by means of hangers with alignment @ 1220mm C/C to soffits. To from grid of 610 X 610mm cross Tee shall be provided @ 610mm C/C in both directions. Suitable provisions shall be made for fixing the recessed / surface mounting light fittings, if any, complete all as specified and as directed by Engr-in-Charge.

S&F for structural steel works of Fe 410W (Gde E 250) quality A, as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc including painted one shop coat of zinc chromate / red oxide primer paint (including preparation of surface) before fabrication complete all as specified and as directed.

S&F Plates (Plain or chequered channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed.

M&L for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 22.5cm and not exceeding 30cm long, Diameter of neck 16mm to 20mm complete all as specified and as directed. Make: - Confirming to IS.

M&L for two coats of synthetic enamel paint tint over primer as red oxide, zinc chrome after preparation of new surfaces of steel of any description, over 10cm in width or girth when unconnected with other painting or when painted in a different tint complete all as specified and as directed.

M&L for one coat of synthetic enamel paint tint after preparation of old surfaces of steel of any description, over 10cm in width or girth when unconnected with other painting or when painted in a different tint complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 18-20mm thick laid over and including cement screed base 20mm thick in cement mortar 1:6 and roughening the surface including cutting as required, rubbing and polishing to granite finish over complete all as specified and as directed.

M&L for machine cut kota stone slab 18-20mm thick as in riser of steps, skirting, dado and pillar laid over and including rendering of 15mm thick in cement mortar 1:4 and jointed with grey cemnet slurry mixed with pigment to match the shade of the slab including cutting as required, rubbing and polishing to granite finish complete all as specified and as directed.

M&L 75mm thick PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection etc, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for two coats of cement based paint including preparation to new surfaces of walls including primer complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of old plastered surface including filling of small holes etc and applying one coat of cement based paint complete all as specified and as directed by Engineer-in-Charge.

S&F in repair stainless steel drapery rods of 25mm dia complete with coloured conical end balls at both end, dia not less than 50mm and fitted with and including MS bracket size 150mm made to shape or 75mm dia MS end wall to wall round block made to shape in male and female pieces as required at site complete all as specified and as directed.

M&L RCC M-25 Design Mix (using 20mm graded crushed stone aggregate) Beams, cantilevers, bressummers, lintels over 1.5m span, as in lintel band complete all as specified and as directed.

Use and waste of form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floors and roofs not exceeding 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide for rough finished surfaces complete all as specified and as directed by the Engineer-in-Charge.

M&L mild steel TMT 10mm dia and over cut to length, bent to shape, required including cranking, bending, spirally for hopping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for mild steel TMT bars 5mm dia and over upto and including 10mm dia as in Binders, stirrups, spacer complete all as specified and as directed.

M&L for excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc and not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in any type of soil complete all as specified and as directed.

M&L for PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in foundation, filling in and mass concrete complete all as specified and as directed.

M&L for Precast RCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in manhole cover slab fixed in position including necessary formwork and set in CM 1:6 complete all as specified and as directed. Note: - Necessary steel reinforcement / TMT bar shall be measured and paid separately under connected items.

M&L brick work with sub class 'B' brick straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4 complete all as specified and as directed.

M&L for Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces complete all as specified and as directed.

M&L for removing excavated soil upto a distance 1.5 Km and depositing where directed complete all as specified and as directed.

E/M Portion:- Taking down old unsv copper/aluminium point wiring concealed / batten (light, fan, socket or power) complete, including fixture and fittings such as switches, sockets, ceiling roses, bell push, bell electric, lamp holder, bulk head fitting, pendants, regulators, sockets, light fitting and any type of switch board wooden / iron, round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc complete all as specified and as directed.

Taking down old and unserviceable, distribution board, any type including MCB's etc after removing all connections and make good the disturbed surface complete all as specified and as directed by Engineer-in-Charge.

M&L for point wiring for one light / fan / 5 Amps independent socket point / call bell point controlled by one 5 Amps switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 Sqmm copper conductor multistranded FRLS, PVC insulated (unsheathed) drawn into and including new concealed PVC rigid / steel conduit 1.8mm wall thickness ISI marked terminated into CI / pressed steel terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified and as directed. Note: - (a) Wiring shall be done by using proper colour coding. (b) Earth wire shall be of green colour. (c) On RCC roof / ceiling PVC conduit shall be provided on surface with proper fixing clips complete all as specified and as directed by Engineer-in-Charge.

Description same as per Ser Item No 55.00 here-in-before but 5 Amp socket outlet on same board complete all as specified and as directed.

Description same as per Ser Item No 55.00 here-in-before but socket outlet 5 Amps on independent board complete all as specified and as directed by Engineer-in-Charge.

Description same as per Ser Item No 55.00 here-in-before but for one 6 pin socket outlet 15 Amps on independent board with cables 2.5 Sqmm size complete all as specified and as directed.

M&L for distribution board sheet steel phosphatised powder coated for MCB with copper bus bar and neutral link earthing stud SPN 12 way 240 Volts double door complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement for MCB SP 6 to 32 Amps, 240 Volts 'B' series complete all as specified and as directed.

S&F in replacement for MCB SPN 40 Amps, 240 Volts, 'B' series complete all as specified and as directed.

S&F in replacement for switch piano, flush type single pole one way 5 Amp, 240 volts complete all as specified and as directed.

S&F in replacement for socket outlet 5 amp / 5 pin flush type complete all as specified and as directed.

S&F in replacement for socket outlet 15 Amps, 240 Volts, 6 pin flush type complete all as specified and as directed.

S&F in replacement for switch piano, flush type single pole one way 15 Amps, 240 Volts complete all as specified and as directed.

S&F in replacement for ceiling rose 3 terminal surface complete all as specified and as directed.

M&L in replacement for lamp holder, insulated body, with back plate suitable for batten fittings complete all as specified and as directed.

M&L in replacement self ballast LED retrofit lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and as directed.

S&F in replacement of new generation energy saving, wall mounted LED tube light batten fittings, extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver 20 watt LED duly fitted on PVC square block 6500K (4' ft long) with LED rod 20 watt, 230 Volts 50 Hz complete all as specified and as directed.

S&F in replacement Stepped type electronic fan regulator flush type on the existing phenolic laminated sheet complete all as specified and as directed.

S&F in repair for Earthing complete with galvanised mild steel earth plate electrode of size 60X60X6.3mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with suitable handle made of round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and directed.

Supply and fixing in repair of LED street light fitting 35 watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

M&L for laying PVC flat serviceable cable, multistranded aluminium conductor 16 Sqmm 2 core in air hang with proper GE earth wire and reinsulators space 1 mtr distance each / on pole / on wall / trenches / through pipe in repair complete with all as specified and as directed by Engr-in-Charge.

M/S PRITHIVI RAJ AND SONS

bushan kumar

Jagbir Singh and Co

M/s Koul & Sons

M/S KARAN SINGH CONTRACTOR

M/S VERMA ENTERPRISES

M/S A K CONSTRUCTION

Shri Karshni Builders

M/S Sudagar Mal

Azurite Engineering

Bidder Name

Shri Karshni Builders

M/S VERMA ENTERPRISES

Jagbir Singh and Co

M/S Sudagar Mal

M/S PRITHIVI RAJ AND SONS

M/s Koul & Sons

bushan kumar

M/S STAR CONSTRUCTIONS

M/S KARAN SINGH CONTRACTOR

Azurite Engineering

M/S A K CONSTRUCTION