Special Repairs to Building No. P - 135 and P - 136 JCO Block at Nausena Baugh, Visakhapatnam

Amount

M & L for 25 mm average thick, PCC 1:2:4, Type B-0, using 10mm graded aggregate as in Padding over roof slabs etc. including mixing water proofing compound as per manufacturers instructions and finishing the top surface rough complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

Supply only integral water proofing compound [ISI marked] of approved make.

M & L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.0 KG of cement per Sq.m area, rendering 10mm thick in cement mortar 1:3 on concrete surfaces finished even and smooth without using extra cement including mixing of water proofing compound of approved make as per manufacturers instructions for levelling the surface smooth to receive the water proofing membrane, priming the surface with a coat of cold applied bituminous primer @ 0.50 KG per Sq.m, applying a coat of Blown Bitumen of grade 85/25 @ 1.2 Kg per Sq.m, laying Polymeric water proofing membrane of weight not less than 3.00 Kg per Sq.m reinforced with polyester non-woven fabric of weight not less than 150 Grams per Sq.m, by torch application with side over lap of 100mm & end over lap of 150mm & tucked into the chases on vertical surfaces by thermo fusion including applying a coat of Blown Bitumen of grade 85/25 @ 1.2 Kg per Sq.m and finished with a coat of bituminous aluminium paint @ 100 grams per Sq.m on top for water proofing treatment complete including taking down existing Roof Treatment of any description and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

Demolition of Unreinforced Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

M & L for 25 mm thick, PCC 1:2:4, Type B-0, using 10mm graded aggregate as in Sub base for flooring complete all as specified and as directed.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Vertical Surfaces such as Skirting, Dado etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

Dismantling of Floor, Hearth or Wall Tiling of any description including Cement Mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris to a distance not exceeding 1.50 KM complete all as specified and as directed.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.06 Sq.m and not exceeding 0.11 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Joint Free Glazed Ceramic Tiles, Edge Cut, Concept Type, Coloured, Premium Quality, of size 450 mm X 300 mm, 7 to 8 mm thick as in Vertical Surfaces such as Skirting, Dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. The colour / shade / design of tiles shall be as approved by GE.

M & L for PCC 1:5:10, Type E-2, using 40mm graded stone aggregate as in Sunken Floors etc complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 10 mm thick in Cement Mortar 1:4, including mixing water proofing compound as per manufacturers instructions and finishing the top surface even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for applying Chemical Injection Treatment in the form of Pressure Grouting by drilling 20 mm dia holes, 60 mm deep @ 100 cm grid at bottom floor and all the internal wall surfaces of the sunken slabs of toilet by injecting Cement Slurry mixed with Grout Admixture "CONBEXTRA EP 10" of M/s. Fosroc Chemicals India [P] Ltd. or its equivalent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Batik India Pvt. Ltd. at 225 Grams for 50 KG of cement complete all as per manufacturers instructions and as directed.

Demolition of Reinforced Cement Concrete [reinforcement cut as required to facilitate demolition] of any description and in any position not otherwise specifically provided for and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

Use and removal of steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including fair finished surfaces complete all as specified and directed.

M & L for RCC M-20 Design Mix, using 20mm graded stone aggregate as in Slabs supported on walls, beams, columns, landings, shelves and the like complete all as specified.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

Demolition of Brick / Stone Masonry built in Cement Mortar including all quoins arches pillars etc and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

M & L for brick work with Fly Ash bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

M & L for brick work in half brick thick walls using Fly Ash bricks straight or curved on plan to any radius built in Cement Mortar 1:4 including 2 Nos of 6mm dia bars at every fourth course of brick work complete all as specified and as directed.

Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces etc including raking out joints, hacking for key scrubbing down with water etc and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 10 mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4, including mixing water proofing compound as per manufacturers instructions and finishing the top surface even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for Cutting / Chipping the spalling concrete surfaces of Slabs, Beams, Columns, Fins, Facias, Parapets & Chajjas etc. and trimming, cleaning the surfaces of any thickness to receive Guniting / Plastering, preparing surfaces and applying a coat of Nito Bond AR of M/s. Fosroc Chemicals or equivalent approved bonding agent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. as per manufacturer's instructions and providing pressure Guniting averaging 25mm thick at a pressure of not less than 6 KG / Sq.cm in Cement Mortar 1:3 with and including suitable bonding agent of M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. @ 5% of weight of cement for sides and soffits of Slabs, Beams, Columns, Fins, Parapets Facias & Chajjas etc., finishing surface rough conforming to proper geometrics including providing double scaffolding and safety measures as required and removal of the same on completion and disposal and depositing the demolished material out of MD land complete all as specified and as directed.

M & L for Cutting / Chipping the spalling concrete surfaces of Slabs, Beams, Columns, Fins, Facias, Parapets & Chajjas etc. and trimming, cleaning the surfaces of any thickness to receive Guniting / Plastering, preparing surfaces and applying a coat of Nito Bond AR of M/s. Fosroc Chemicals or equivalent approved bonding agent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. as per manufacturer's instructions and providing pressure Guniting averaging 30mm thick at a pressure of not less than 6 KG / Sq.cm in Cement Mortar 1:3 with and including suitable bonding agent of M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. @ 5% of weight of cement for sides and soffits of Slabs, Beams, Columns, Fins, Parapets Facias & Chajjas etc., finishing surface rough conforming to proper geometrics including providing double scaffolding and safety measures as required and removal of the same on completion and disposal and depositing the demolished material out of MD land complete all as specified and as directed.

M & L for Welding in repairs exceeding 2.5cm but not exceeding 5cm in length and thickness of metal welded exceeding 6mm and not exceeding 9mm complete all as specified and as directed.

M & L for Welding in repairs exceeding 2.5cm but not exceeding 5cm in length and thickness of metal welded exceeding 9mm and not exceeding 20mm complete all as specified and as directed.

Use and removal of steel formwork to Chajjas, Fins, Louvers, Fascia and similar works etc., vertical or to batter for fair finished surfaces complete all as specified and as directed. sides of concrete

M & L for RCC M-20 Design Mix, using 20mm graded stone aggregate as in Chajjas, Facias & Fins etc. complete all as specified and as directed.

M & L for preparation of old plastered or unplastered surfaces including brooming down or steel wire brushing and applying two coats of white wash on ceilings complete all as specified and as directed.

M & L for preparing newly plastered ceiling surfaces and applying three coats of white washing complete all as specified and as directed.

M & L for preparing newly plastered wall / Ceiling surfaces and applying two or more coats of Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Acrylic Washable Distemper over a coat of alkali resistant primer on wall / Ceiling surfaces complete all as specified and as directed.

M & L for Complete removal of existing treatment of any description on wall / Ceiling surfaces and applying two or more coats of Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Acrylic Washable Distemper over one of alkali resistant primer on wall / Ceiling surfaces complete all as specified and as directed.

M & L for preparing newly plastered wall surfaces and applying three coats of white washing complete all as specified and as directed.

M & L for preparation of old plastered or unplastered surfaces including brooming down or steel wire brushing and applying two coats of white wash on walls complete all as specified and as directed.

M & L for preparation of newly plastered wall / Ceiling surfaces and applying Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] over a Coat of Weather Proof Exterior Primer of same manufacturer as that of paint complete all as specified and as directed.

M & L for complete removal of existing treatment on wall surfaces and applying Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] over a Coat of Weather Proof Exterior Primer of same manufacturer as that of paint complete all as specified and as directed.

M & L for preparation of old painted wood and wood based surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M & L for Writing letters or figures [Block, Roman, Italic or Indian] not exceeding 30 cm high complete all as specified and as directed.

S & F in repairs 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F in repairs 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps as in rain water down pipes complete all as specified and as directed.

S & F in repairs 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps as in rain water down pipes complete all as specified and as directed.

S & F in repairs 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F 75mm bore PVC [SWR] Multi Floor Trap with grating including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal with access door including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Bends of any radius with Access Door including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Branch Piece, Double [Double "Y"] equal or unequal without access door including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed.

S & F 20mm outer dia of pipe, 3–layer PP–R Polypropylene random copolymer] concealed pipes of SDR 7.4 [PN–16] UV stabilised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings complete to walls, ceilings or in floors etc. including testing including taking down or up steel tubing and connections of any description complete all as specified and as directed.

S & F 25mm outer dia of pipe, 3–layer PP–R Polypropylene random copolymer] concealed pipes of SDR 7.4 [PN–16] UV stabilised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings complete to walls, ceilings or in floors etc. including testing including taking down or up steel tubing and connections of any description complete all as specified and as directed.

S & F in repairs Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type, Short Body with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as specified and as directed.

S & F in repairs, Stop Valves, 15 mm bore dia of pipe, Fancy type, Chromium Plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions etc complete all as specified and as directed.

S & F in repairs Angle Cock, 15 mm dia, cast copper alloy with capstan head, Chromium Plated, screwed down high pressure with crutch or butterfly handle for iron pipe etc. complete all as specified and as directed.

S & F in repairs Brass Chromium Plated Shower Rose of size 125mm with or with out swivel joints fixing to steel pipes complete all as specified and as directed.

S & F in repairs Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 Mpa, 25 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to IS, ISI Marked complete all specified and as directed.

S & F in repairs Stainless Steel, Soap Dish, Fancy Type complete all specified and as directed.

S & F in repairs Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats [Minimum weight 90 Grams] complete all as specified and as directed.

S & F in repairs PTMT Tubular Towel Rail, 20mm dia, D Type, 450 mm long between flanges, fixed with and including Chromium plated brass screws and wooden/plastic cleats [Minimum weight 170 Grams] complete all as specified and as directed.

S & F in repairs Vitreous China Wash Down Water Closet [Pedestal pattern], White, including 10 Litres capacity, PVC Valve less, Syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle, flush pipe of polyethylene of low or high density of PVC, 32mm dia, PVC Connection of 15mm Bore and 600mm long with PTMT check nut and union etc. including brackets and connections to pipe and flush pipe including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap complete all as specified and as directed.

S & F in repairs Vitreous China Ware Wash Hand Basin, White, Flat Back of size 550 mm X 400 mm including Pillar Taps, cast copper alloy, Chromium Plated, Fancy Type, 15 mm dia, with capstan head, screwed down high pressure with or without lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe, 32mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible Waste Pipe, PVC Connection of 15mm Bore and 600mm long with PTMT check nut and union etc. complete all as specified and as directed.

S & F in repairs Stainless steel kitchen sink with drainage board, made of stainless steel sheet of 1 mm thick, with plugs, washers, Waste Fittings, 32 mm dia, Brass, Chromium plated, and 32mm dia PVC flexible Waste Pipe, 750 mm long, including bedding in Cement Mortar to dwarf wall or including fixing cantilever CI Brackets and connecting union to waste pipe, over all size 915 mm x 460 mm bowl size 410 mm x 355 mm x 165 mm complete all as specified and as directed.

S & F in repairs Stainless Steel Kitchen Plate Rack of size 600 X 900 X 250mm, made of 1.50mm thick stainless steel sheet complete all as directed. [Make: Prayag / Nirali / Jayna / Neelkant]

Taking down Chowkats or frame with shutters [without taking off shutter from the frame] not exceeding 1.5 Sq.m each and removing to store complete all as specified and as directed.

Taking down Chowkats or frame with shutters [without taking off shutter from the frame] exceeding 1.5 Sq.m but not exceeding 4.00 Sq.m each and removing to store complete all as specified and as directed.

Taking down Shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each complete all as specified and as directed.

Taking down Shutters of any description not exceeding 1.00 Sq.m each complete all as specified and as directed.

Taking down and refixing in the same opening shutters of any description exceeding 1.00 Sq.m and not exceeding 2.00 Sq.m each after easing and adjusting complete all as specified and as directed.

S & F Solid PVC door frame of size 100mmX45mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening complete all as specified and as directed.

S & F Factory made solid panel PVC door shutter 30 mm thick [Style] consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC "C" Channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement fixing in frame at site as per specification complete all as specified and as directed.

S & F Factory made, 40 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S & F Factory made, 35mm thick, Second Class Hard Wood, Plain framed, Panelled Shutter [Two Panel] with Lock Rail and Panel of 9 mm BWP Commercial Ply or 12 mm Veneered Particle Board with Commercial Veneering on both faces, the size of Rail and Stile as per IS – 1003 [Part – I], Kiln Seasoned and Chemically Pressure treated and fitted to Chowkats complete all as specified and as directed.

S & F Factory made, 35mm thick, Second Class Hard Wood, Glazed and Skeleton Shutters, open rebated and prepared to receive glass, gauze, etc., divided into squares, with plain, chamfered or rounded, mitred and rebated Sash Bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part – I, Section 8, Clause 8.24 [b] and fitted to Chowkats complete all as specified and as directed.

S & F Second Class Hard Wood, plain, solid, straight Chowkats and Frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

S & F Mild Steel work conforming to Fe - 290, Grade E-165 as in Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes, including Bolts, if required, Hooks [Stay], heavy, for Large Gates, Hook and Pintle Hinges, large Hasps and Staples, Chains, hand made Sliding Bolts, Clamps, Hold Fasts, Wall Ties, Hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

M & L for Plain / Reinforced cement concrete Type C1 [Nominal Mix] 1:3:6 using 20mm graded stone aggregate cast in situ in lintels up to 1.5m span, Cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work, complete all as specified and as directed.

S & F Factory made UPVC Sliding Window, Three Track, White Colour of area not exceeding 2.0 Sq.m, made of extruded profiles with wall thickness of 2.3mm±0.2mm, Window profile with hollow section with multi chamber, Frame of size 112mm X 52mm, Sliding Sash of size 42mm X 67mm, Sliding Mesh Sash of size 42mm X 57mm, Sliding Interlock [One vertical length in each shutter] of size 45.50mm X 28mm, Glazing Bead of size 24.50mm X 16mm shall be mitred cut and fusion welded at all corners, including drilling holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM Gasket, 1.2mm±0.2mm thick Galvanized Steel Frame of size 30mmx 10mm, 2 Nos, Sliding Sash of size 30mm x 10mm, Sliding Mesh Sash of size 26mm x 10mm, profile to be inserted in required profile, frame shall be fixed to the wall with 8mm X 100mm long fasteners, Hardware such as Touch lock of zinc alloyed [white powder coated], Steel roller system, Stainless Steel Wire Cloth of 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories shall be provided with proper operative and locking hardware mechanism, frame shall be fixed to wall with high quality fasteners and silicon glue shall be applied to fill up gap between frame and wall to make leak proof complete all as specified and as per Manufacturer instructions. Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.

Supply only 5mm thick Sheet Glass ordinary quality in squares exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

Supply only 5mm thick Sheet Glass ordinary quality in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

Supply only 5mm thick Figured Glass ordinary quality in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

Supply only Stainless steel wire cloth / mesh with average aperture not exceeding 1.40 mm and dia of wire 0.36 mm complete all as specified and as directed.

S & F Aluminium alloy anodised Sliding Door Bolt with hasp and staple [Bolt Type] of size 300 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F in repairs Aluminium alloy anodised Sliding Door Bolt with hasp and staple [Bolt Type] of size 300 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt of size 150 mm size of extruded section complete all as specified and as directed.

S & F in repairs Aluminium anodised barrel Tower Bolt of size 150 mm size of extruded section complete all as specified and as directed.

S & F 125 mm size, Butt hinges, Stainless Steel, Medium weight, bright polished including fixtures complete all as specified and as directed.

S & F in repairs 125 mm size, Butt hinges, Stainless Steel, Medium weight, bright polished including fixtures complete all as specified and as directed.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and as directed.

S & F in repairs Aluminium anodised Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and as directed.

M & L for two coats of synthetic enamel paint over one coat of pink primer to newly untreated wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

S & F Floor Door Stopper of size 150 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

S & F in repairs Decorative type Stainless Steel Curtain Rod of 25 mm dia including PVC rings @ 100 mm centre to centre and Decorative type Stainless Steel Globe type Brackets of size suitable to 25mm dia curtain rod complete all as specified and as directed.

S & F in repairs 18mm thick Plywood, Grade BWR, Type BB, fixed with screws to Wooden Frames complete all as specified and as directed.

S & F 0.9 mm thick Decorative Laminate, Type - 1 of Surface Finish, Colour and Pattern as approved, fixed with approved adhesive as per manufacturer's instructions, complete all as specified and directed.

S & F First Class hard wood plain, cover fillets, square, rectangular or triangular in section, bull nosed, splayed, chamfered or chamfered or rounded on one edge or face wrought, secured with screws, cross sectional area exceeding 3 Sq.cm and not exceeding 6 Sq.cm complete all as specified and as directed.

S & F 75 mm size, Butt hinges, extruded Brass, with mild steel hinge pin, bright polished, Type D-11 including fixtures complete all as specified and as directed.

S & F Continuous [Piano] Hinges, Mild Steel, Bright finish or Electrogalvanised and width of Flaps 40mm [When Open] complete all as specified and as directed.

S & F Cup Board Locking Device, Brass, Chromium Plated, 75mm, 4 levers with duplicate keys, First quality complete all as specified and as directed.

S & F Brass Handles, Cast Type, Polished Bright of size 100mm long complete all as specified and as directed.

S & F Magnetic Catches with Striking Plate, First quality complete all as specified and as directed.

S & F Mild Steel Door Spring 375 mm, Ordinary Rat Rail Rod Pattern springs including roller and roller plate complete all as specified and as directed.

S & F Night Latch, Vertical type, Brass body of size 100 mm, and 7 Levers with 3 keys of Godrej Make, complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment along external walls below concrete or masonry apron using chemical emulsion @ 2.25 litres per RM by drilling 12 mm dia holes up to 300 mm deep and 300 mm centre to centre including plugging holes complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment of soil under existing floors using chemical emulsion @ 1 litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment at points of contact of wood work by chemical emulsion [in oil or kerosene based solution] @ 0.5 litre per hole by drilling 6 mm dia holes at a downward angle of 45 degrees at 150 mm centre to centre and sealing the same complete all as specified and as directed.

S & F Second class hard wood small fittings such as brackets of any type, shaped door and window stops and the like including all necessary Labour, articles not exceeding 200 Cu.cm each complete all as specified and as directed.

S & F Hat and Coat Hooks, Brass Chromium plated, of size not less than 175mm complete all as specified and as directed.

S & F Hasp and Staple, safety type of aluminium anodised including bolt to hinge plate, fixed with screws of 75mm size complete all as specified and as directed.

S & F Mild Steel work conforming to Fe - 290, Grade E-165, as in framed work such as Grills, Gratings, Ladders etc with ends of bars shouldered and/or riveted, or forged into spikes, framed Guard Bars, Barred Iron Doors, Ladders, framed Balusters, Walk Ways, Railings, framework of Water Tanks and similar work complete all as specified and as directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces not exceeding 10cm width or girth including preparation of surfaces complete all as specified and as directed.

S & F Mild Steel, Plain, Black Sheet, 0.8mm thick as in hearths, covering to door shutters, covering to door Chowkats [frames], Chullah hoods, water tanks, water troughs, ducts, urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel members, etc. with plain 40 mm lap joints or welded / riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required including applying two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

S & F in repairs Two way Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as specified and as directed.

S & F in repairs Health Faucet with 1 m long flexible tube, wall hook, non return valve complete as per Jaquar Catalogue No. ALD-577 or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Rotational Moulded Polythene [HDPE] Water Tanks, Triple Layered, ISI Marked, Cylindrical & Vertical Type 1000 Litres Capacity hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete including taking down old tanks and removing to store complete all as specified and as directed.

S & F in repairs Ball Brass Valve, 20 mm dia, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule complete all as specified and as directed.

Dismantling of Structural Steel work including Doors, Gates etc but excluding framed trusses complete all as specified and as directed.

S & F 15 mm size, PVC Corner Beading, fixed to tile corner joints complete all as specified and as directed.

Supply only Powder Coated Aluminium Deco Grill of Model / Design No. DG 104, including Powder Coated Aluminium Channel of size 30 X 12 X 1mm for fixing Deco Grill complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal with access door including jointing with solvent cement complete all as specified and as directed.

M & L for installation of Non Returnable Grouting Packer of 8mm dia and drill hole of 10 mm dia for epoxy grouting including cleaning of holes in position, all equipment, putty, machinery, tools as recommended by the Manufacturer complete all as specified and as directed.

M & L for Drilling Holes In Concrete with suitable equipment in columns, beams, slabs, walls etc. to the required depth as directed by the Engineer-in-charge to facilitate anchoring of reinforcement bars into the core concrete etc. including working platforms, equipment, machines, skilled manpower etc. complete all as specified and as directed. Note: In case reinforcement or coarse aggregate is encountered during drilling holes in concrete, further drilling shall be stopped and holes shall be re-drilled at different location. Failed / suspended drilled holes shall not be considered for measurement and payment.

M & L for Cleaning the existing exposed reinforcement of slab, beam, column, footing etc. and any other RCC structural member by emery paper, providing two coats of rust remover and rust preventer [Single Component Rust Removal And Rust Inhibition Liquid i.e. Sika Rustoff 100 of M/s. Sika India Pvt. Ltd. or equivalent approved bonding agent in M/s. Fosroc Chemicals or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. as per manufacturer's instructions] complete all as specified and as directed. Note: The work shall be executed as per manufacturer’s data sheet and instructions.

M & L for cleaning the existing exposed concrete surfaces and applying Bonding Agent i.e. Sikadur-32 / Sikadur-32 LP of M/s. Sika India Pvt. Ltd. or equivalent approved bonding agent in M/s. Fosroc Chemicals or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. as per manufacturer's instructions to create structural bonding between old concrete surface and new concrete complete all as specified and as directed.

M & L for preparation of existing exposed steel surfaces free from dust, loose material, surface contamination, rust, scale, mortar, concrete, other loose and deleterious materials, materials which reduce bond or prevent suction or wetting by repair materials, delaminating, weak, damaged and deteriorated concrete by blast cleaning or other means of mechanical abrasion or suitable means, making substrata to Saturated Surface Dry [SSD] with no standing water and applying cement-based epoxy modified three-component anti corrosive coating and bonding slurry using Friazinc R of M/s. Sika India Pvt. Ltd. or equivalent approved bonding agent in M/s. Fosroc Chemicals or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. as per manufacturer's instructions as in rebar corrosion protection system complete all as specified and as directed.

M & L for applying pre-batched One Component Polymer Modified Protective Mortar [PMPM] for repair of spalling and damaged concrete in RCC structures and superstructure works using Sika Top-122 of M/s. Sika India Pvt. Ltd. or equivalent approved bonding agent in M/s. Fosroc Chemicals or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. as per manufacturer's instructions, finishing the top surface even and smooth without using extra cement conforming to proper geometrics complete all as specified and as directed.

M & L for providing Non-Shrink, Cementitious Micro Concrete using Rendroc RG manufactured by M/s. Fosroc Chemicals India [P] Ltd. or its equivalent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. modified with 6.4mm graded, clean, saturated surface dry crushed stone aggregate in the ratio as per manufacturer's instructions, as in columns, beams and similar structural members including use and waste of water tight formwork to facilitate pouring of micro concrete complete all as per manufacturer's instructions at a pressure of not less than 6 KG / Sq.cm to ensure dense, properly compacted, free from honey combs etc. and finally rendering 15 mm thick in Cement Mortar 1:3 and finishing the top surface even and smooth without using extra cement conforming to proper geometrics complete all as specified and as directed. [Note: Measurement shall be considered for circumference at centerline of core thickness]

M & L for Carbon Fibre Wrap around outer face of the column & beam for full length complete all as specified herein below and as per manufacturer's specifications / recommendations complete all as specified and as directed: [a] Surface Preparation: The surface shall be thoroughly cleaned with brush and cotton to remove all dust, loose material, surface contamination. Undulations if any noticed shall be brought to uniform surface to make the edges of columns round by applying solvent free, moisture tolerant, thixotropic, structural two-part epoxy adhesive / mortar. [b] Thereafter Wrap Strengthening System shall be applied by using epoxy adhesive on the prepared surface with proper roller to remove air voids as per manufacturer’s instructions. [c] Wrap Strengthening System for Beam & Slab shall be Sika CarboDur of M/s. Sika India Pvt. Ltd. and or equivalent approved bonding agent in M/s. Fosroc Chemicals or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. [d] Wrap Strengthening System for Column shall be Sika Wrap of M/s. Sika India Pvt. Ltd. and or equivalent approved bonding agent in M/s. Fosroc Chemicals or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. [e] Fire Protection Mortar shall be Sikacrete-213 F of M/s. Sika India Pvt. Ltd. and or equivalent approved bonding agent in M/s. Fosroc Chemicals or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. [f] UV Protection System over Sikadur-330 shall be applied.

M & L for providing additional reinforcement using High Strength Corrosion Resistant Deformed Bars of Grade Fe–500D of make HILTI – HIT RE 500 Post Installed Rebar by checking the diameter of the existing bars, cutting the necessary main reinforcement to the required length with proper development length, tying and binding with 16 SWG black soft annealed binding wire / welding where required / lapping / anchoring with the existing shear connectors / reinforcement so that the additional reinforcement acts monolithically with the existing reinforcement and core concrete complete all as specified and as directed. Note: The shear reinforcement shall also be provided as specified here-in-above in the form of 2 "U" shaped bars if existing shear reinforcement is found deteriorated / diameter of the bars is reduced to form a rigid cage and placing with proper cover block, supports, chairs, spacers etc. Diameter of the new bar shall be equal to the existing bars. Additional reinforcement shall be provided only in case the diameter of the existing bars is found less than 25% of the original diameter. Note for Serial Item No. 127 to 135: The work of structural rehabilitation shall be got carried out under the supervision and guidance of structural consultant who carried out the NDT and submitted report [M/s. IDDC Engineers Pvt Ltd.]. A certificate from consultant shall be obtained by the contractor to the effect that work of structural rehabilitation has been carried out under their strict supervision and the same shall be submitted by the contractor to GE. The contractor shall also obtain a written guarantee for effectiveness for a period of 5 [Five] Years from the certified date of completion of entire work from the manufacturer and submit the same to GE before claiming payment. Rate quoted is deemed to be including providing double scaffolding and safety measures as required and removal of the same on completion and disposal and depositing the demolished material out of MD land complete all as specified and as directed. Nothing shall be paid extra on this account.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Steps, Jambs, Pillars, Window Cills, Cooking Platform etc. and the like with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single stone slab shall be used for entire height of Steps, Jambs, Pillars, Window Cills, Cooking Platform etc. and joints shall match with the flooring

M & L for Marble Stone Slabs of 18 to 20 mm thick of Green Colour as in Flooring, Treads and Risers of Steps, Landings of Staircase etc. with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, slabs shall be of design / pattern as directed, including inlays, borders, margins, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious joint filler to match the shade of the Slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single stone slab shall be used for entire width of Steps, Risers & Landing etc. and joints shall match with the flooring. The edges of treads shall be bull nosed / half rounded. The edges of the treads and landings shall also be provided with three Nos of grooves.

S & F in repairs Glass Shelf with Chromium plated Bracket of size 450 X 150mm complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plan area and not exceeding 1.5m deep in Soft / Loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.

Removal of excavated material [Soil] to a distance exceeding 250m and not exceeding 500 m and depositing where directed at a level not exceeding 1.5 m complete all as specified and as directed.

Demolition of Cement Concrete of any description and in any position not otherwise specifically provided for and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

M & L for PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for providing Precast RCC 1:2:4, Type B-1 using 20mm graded stone aggregate as in landings, cover slabs [for manholes etc], Chullah hoods, Chajjas, water troughs, mangers, Shelves and similar articles with plain faces set in cement mortar 1:6 complete all as specified and as directed.

M & L for 150 dia for Salt Glazed Stoneware Drain Pipes of Grade "A" laid in trenches and jointed including Demolition and breaking up drain pipes [Salt glazed ware, AC or Reinforced concrete] of any diameter set in cement mortar complete all as specified and as directed.

M & L for 200 dia for Salt Glazed Stoneware Drain Pipes of Grade "A" laid in trenches and jointed including Demolition and breaking up drain pipes [Salt glazed ware, AC or Reinforced concrete] of any diameter set in cement mortar complete all as specified and as directed.

M & L for concrete bed to drain pipes of size 150 mm bore packing under and haunching against the sides of pipes after they are laid and fitted in cement concrete, Type C2, 1:3:6, using 40mm graded stone aggregate complete all as specified and as directed.

M & L for concrete bed to drain pipes of size 200 mm bore packing under and haunching against the sides of pipes after they are laid and fitted in cement concrete, Type C2, 1:3:6, using 40mm graded stone aggregate complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel [½ round or ¾ section] in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required for 150 mm dia of pipe complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel [½ round or ¾ section] in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required for 200 mm dia of pipe complete all as specified and as directed.

M & L for Hardcore of gauge not exceeding 63mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rolled with power road roller of 8 to 12 ton capacity and consolidated to required gradient and camber complete all as specified.

M & L for 75 mm thick, PCC 1:3:6, Type C-2, using 40mm graded stone aggregate as in Floors / Hard standing / Path etc., surface finished fair and even complete all as specified and as directed.

M & L for Inter Locking Paving Blocks of 60mm thick, made with M35 Grade cement concrete using 20 mm graded stone aggregate, Hydraulically pressed of approved colour and pattern, shape and size conforming to IS - 15658 complete all as specified and directed.

M & L for Sand Filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M & L for Forming Expansion Joint, 12mm thick, filled with Preformed Bituminous Filler and top 30mm Primed and sealed with Sealing Compound Grade "A" for 75mm thick flooring complete all as specified and directed.

M & L for PCC 1:3:6, Type C-1 [using 20 mm graded granite stone aggregate] in surface channels and drains including forming fair finished drain or channel of any inner girth using extra cement including forms, moulds, mitred / stooped ends complete all as specified and as directed.

Taking down carefully copper / aluminium point wiring [light, fan, socket or power] complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and making good the disturbed surfaces all as per existing complete all as specified and as directed.

M & L for Point Wiring complete with 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, conforming to IS - 694 drawn through and including heavy duty PVC Conduit, 20 mm dia including all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type and Pressed Metal Flush Box made out of 2mm thick MS Sheet of suitable size and 3 mm thick Hylam Sheet top cover for fixing switches, fittings, regulators etc. concealed in walls, including 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable as earth continuity conductor with colour coding and connecting to Earth Dolly for One Light / Fan Point / Bell Point controlled by One Switch complete all as specified and as directed.

All as per Serial Item No. 158 above but for One Light Point controlled by Two Nos. of, Two way Switches complete all as specified and as directed.

All as per Serial Item No. 158 above but One 3 Pin Switch Socket Outlet 5 Amps on Independent Board complete all as specified.

All as per Serial Item No. 158 above but one 3 Pin Switch Socket Outlet 15 Amps on independent board, with 1100 Volts, FRLS grade, 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable confirming to IS - 694 and including 1100 Volts, FRLS grade, 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable as Earth Continuity Conductor.

All as per Serial Item No. 158 above but for one SP & N Enclosure with 2 Pole and Earth Metal Plug & Socket, with 1100 Volts, FRLS Grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, conforming to IS - 694 and including 1100 Volts, FRLS Grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, conforming to IS - 694 as earth continuity conductor and connecting to earth dolly complete all as specified and as directed.

S & F Switch Piano, Flush Button, Single Pole, One Way, 5 Amps, 230 Volts complete all as specified and as directed.

S & F Switch Piano, Flush Button, Single Pole, Two Way, 5 Amps, 230 Volts complete all as specified and as directed.

S & F Ceiling Rose, Surface Bakelite, 65 X 50 mm, Three Terminals, 230 Volts complete all as specified and as directed.

S & F Bell Push, Flush Button, Single Pole, 5 Amps, 230 Volts complete all as specified and as directed.

S & F Switch Socket Outlet, 3 & 2 Pin, Multipurpose, 5 Amps, 230 Volts, Flush Type complete all as specified and as directed.

S & F Switch Socket Outlet, Multipurpose, 3 pin, 15 Amps and 3 pin, 5 Amps, Flush Type, 230 Volts controlled by One Switch complete all as specified and as directed.

S & F Bell, Ding Dong / Multi Music Type, AC, 230 Volts, Single Pole complete all as specified and as directed.

S & F Electronic Fan Regulator, Stepped Type, Flush Type, AC, 230 Volts, Single Pole complete all as specified and as directed.

S & F Lamp Holder, Insulated Body with Back Plate, 230 Volts for Batten Fittings complete all as specified and as directed.

S & F in repairs SP & N Enclosure with 2 Pole and Earth Metal Plug & Socket for incorporating SP MCB complete including One MCB, SP, 20 Amps, 240 Volts complete all as specified and as directed.

M & L for Sub main wiring with 2 runs of single core 4 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 25 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor including taking down old sub main wiring of any description and making good disturbed surface complete all as specified and as directed. Note: 3 runs of 4 Sq.mm & one run of 25 mm dia PVC Conduit will be measured as one unit

M & L for Sub main wiring with 2 runs of single core 6 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 25 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 6 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor including taking down old sub main wiring of any description and making good disturbed surface complete all as specified and as directed. Note: 3 runs of 6 Sq.mm & one run of 25 mm dia PVC Conduit will be measured as one unit

S & F in repairs MCB DB, SPN, 8 Way, 240 Volts, with DIN Channel, Double Door with 200 Amps rated bus bar suitable for mounting MCBs complete all as specified and as directed.

S & F in repairs MCB DB, TPN, 4 Way, 415 Volts, Vertical, with DIN Channel, N3 Frame, Double Door with 250 Amps rated bus bar suitable for mounting MCBs and provision for MCCB as incomer complete all as specified and as directed.

S & F MCCB, FP, 100 Amps, 25 KA, 415 Volts, 50 Hz, suitable for fixing on N3 Frame complete all as specified and as directed.

S & F MCB, SP, 6 to 32 Amps, 10 KA, AC, 230 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, SPN, 40 to 63 Amps, 10 KA, AC, 230 Volts, 50 Hz complete all as specified and as directed.

S & F in repairs TV Socket / Outlet, Co-Axial, Flush Type including suitable Pressed Metal Flush Box made out of 2mm thick MS Sheet, Cover Frame complete all as specified and as directed.

S & F in repairs LAN Outlet, RJ 45, Flush type, including suitable Pressed Metal Flush Box made out of 2mm thick MS Sheet, Cover Frame complete all as specified and as directed.

M & L for Taking down Ceiling Fan of any description from its position and refixing the same after repairs to buildings, at same place or at new place including connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm including cleaning, greasing and spray painting with two coats of synthetic enamel paint of approved colour over a coat of zinc chrome primer after filling cavities with filler and replacement of Spares such as Bearings, Shaft Bushes, Capacitor, Cotter Pin, Clamps, Rubber Bushes, Nuts & Bolts etc. as required complete all as specified and directed.

S & F Microprocessor based Single Phase, Electronic Tamper Proof Digital Energy Meter with bright LCD Display, with Tamper and Fraud detection and recording with snap shot, of High Accuracy, of Rating 10 to 60 Amps with Optical Communication Port, with Class 1 Accuracy, IP 51 Ingress Protection, Conforming to IS - 13779, CBIP Publication No. 304, suitable for 240 Volts, AC, 50 Hz, ISI Marked, including housing in suitable size Polycarbonate Meter Box with provision for Earth Connection, Two separate cable entries for incoming and outgoing cables, Transparent Glass Door for reading visibility with hinges and provision for sealing, including disconnecting and removing old unserviceable energy meters and depositing at MES Store Yard complete all as specified and as directed.

Earthing complete with Galvanised Steel Earth Plate Electrode 600 X 600 X 6 mm thick burried directly in ground [earth pit not less than 2.25 m deep below ground level] with top edge of Plate not less than 1.50 m below normal ground level connected to 32 X 6mm GI Strip [Earth Lead] and GI pipe 50 mm, Medium Grade for earthing lead protection to the extent of maximum 7.5m, Earth Plate Electrode surrounded by 150mm thick packed layers of Charcoal and Common Salt filled in alternate layers, connected to the Plate by means of GI Bolts & Nuts complete all as per Electrical Plate No. 3 of SSR Part – I, connected to panel / DB including testing on completion including main earthing, Charcoal, Common Salt, PCC [1:2:4, Type B1] Pit with RCC 1:2:4, Type B1 Cover, 50 mm thick with 6 Nos, 8 mm dia TMT bars in both ways, MS frame made with 40 X 40 X 6 mm Angle Iron, MS Funnel with 20 mm bore, medium grade GI Watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc. and disconnecting and taking down existing Earthing of any description complete all as specified and as directed.

Supply and draw through and including heavy duty PVC Conduit, 20 mm dia with all accessories, PVC armoured Co-Axial Cable, RG 6 [Foam], black in colour, Electrolytic Grade solid annealed Copper conductor, Jelly filled, Aluminium Foiled and Aluminium wire Braided heavy AVG for cable for Cable TV / Satellite TV including all connecting accessories complete all as specified and as directed.

Supply and draw through and including heavy duty PVC Conduit, 20 mm dia with all accessories, PVC Insulated LAN / Network Cable, Electrolytic grade solid annealed bare copper conductor, 4 Pair, unshielded twisted pair [UTP] Industrial cables with star separator for LAN Network complete all as specified and as directed.

N Sydeswara Rao

RAGHU RAMA PANDA

S A R CONSTRUCTIONS

ANIL KUMAR BISWAL

Mavee Syndicate