SPL REPAIR TO BLDG NO T-15 (OR LINE) OF 77 MTN BDE SIG COY AT SECT-1A AND CERTAIN OTHER SPECIAL REPAIR WORKS AT THAKURBARI UNDER GE (NORTH) TEZPUR

Amount

Note 1: (Applicable for all parts/items) : The biidders/contractors are advised to read tender document, all drawings & all corrigendum/amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected. Fixed credit has been given in technical documents which shall be taken into account during acceptance of bid/tender.

Dismantling of floor hearth wall tiles incl cement mortar bedding mortar. Removing servicable tiles to store and rubbish off premises complete

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15 cm thickness ( below or above ground level).

Demolition of re-in-forcement cement concrete in any description and in any position not otherwise specifically provided for

Demolition of brickwork masonry built in cement mortar including all quoins, arches pillars etc.

Demolition of reed ,lathing, single or double , including battens and plaster or chicken wire lathing.

Dismantling of Asbestos cement (corrugated or semi-corrugated etc) sheets in roof coverings

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets.

Dismantling boarding, any description, fixed in any position with nails

Dismantling of timber scantlings 40 Sqcm and over in section in any position (unframed work)

Dismantling of timber but in fillets, rails, posts, rafters, purlines etc.under 40 Sqcm in section.

Taking down Chowkats or frames exc 1.5 sq.m but n exc 4 sq.m each with shutters (without taking off shutters from the frame).

Taking down Chowkats or frames n exc 1.5 sq.m each with shutters (without taking off shutters from the frame).

Taking down shutters but exc 1 Sq.m and n.exc 2 Sq.m each

Taking down shutters exc 2.00 sq.m each

Taking down shutters n exc 1.00 sq.m each

Taking down cement plaster on brick work surfaces including racking out joints, hacking for key ,scrubbing down with water etc.

Taking down or up steel tubing and connections inculding cleaning for refixing or removal to store 15mm bore

Taking up or down 20mm bore steel tubing and connections, including cleaning for re-fixing or removal to store.

S&F 15mm bore tubes medium grade galvanized with all fitting and fixed complete to walls and ceilings or laid in floors of any length all as specified and directed by Engr-in-charge. Make:- Jindal/ Prakash /TATA

S&F 20 mm bore tubes medium grade galvanized with all fitting and fixed complete to walls and ceilings or laid in floors of any length all as specified and directed by Engr-in-charge. Make:- Jindal/ Prakash /TATA

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S & F for straps, supports or stay for rain water, hook and pintel, clamp, hold fast, wind ties, hook for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters and smilor work conforming to Fe 290 Gde E-165

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified

M&L for mild steel angle iron/MS pipe post as in purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. using Fe 410-W (Gde E-250) quality B complete all as specified and as directed.

All as per item no 25 above except erection and fixing only. Note : Material retrieved from Ser no 24 above shall be used for fixing.

M & L brick work with subclass ‘B’ bricks, straight or curved on plan exc 6 m mean radius built in Cement mortar 1:6 .

M&L for brickwork with sub class’B’ bricks, straight or curved on plan exc 6m mean radius in half brick work built in CM 1:4.

M&L GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding , joists, etc. In walls, ceilings, stanchions, beams, bird proofing etc. Including all laps , cutting and waste.

M&L 10mm thick plastering on fair faces of bricks or cone surfaces finished even and smooth w/o using extra cement in cm1:6.

M&L for rendering 15 mm thick plastering but as in CM 1:4 on fair faces of brick work with using water proofing compound over it.

M&L 15mm thick rendering in CM 1:6 to brick/conc wall surfaces trowelled to even & smooth w/o using extra cement.

M&L, 15mm thick rendering in CM 1:4 to brick/conc wall surfaces trowelled to even & smooth w/o using extra cement.

M&L for rendering 10 mm thick plastering but on one side of lathing in CM 1:4

M&L for rendering 15 mm thick plastering but on other side of lathing floating/setting coat using water proofing compound over it in CM 1: 4.

Supply only water proofing compound.

M&L second class wrought hard wood in scantlings (Timber fixed).

M&L for 50mm thick planed at both sides boarding as in rafters,truess and members complete all as specified and directed

M&L for 50mm clean sawn as in joist of ceiling complete all as specified and as directed.

M&L for 20mm thick second class hardwood planed at both sides boarding as in eaves boards

S& F Anodised aluminium snap grid frame of size 605 x605 work for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof by means of ceilling cleats/ 2 mm dia wire made out of G.I. flat 40 x 3 mm size 60mm complete all as specifiedall as specified and as directed

M&L 4mm Non asbestos fibre cement building fixed or laid/inserted to ceiling timber/GI/Aluminium framework with screws

M&L for 2nd class hard wood plain fillets ,square, rectangular or triangular in section ,clean sawn ,secured with nails or brads (sectional area exc13 sq.cm & n exc 25 sq.cm)as in studs of ceiling / sunshed.

M&L for 2nd class hard wood plain fillets ,square, rectangular or triangular in section ,clean sawn ,secured with nails or brads (sectional area exc6 sq.cm & n exc 13 sq.cm) as in ceiling/ jali window frame/bird proof complete all as specified

M&L for 2nd class hard wood plain fillets ,square, rectangular or triangular in section ,clean sawn ,secured with nails or brads (sectional area exc 3 sq.cm & n exc 6 sq.cm)as in filet etc..

S&F for second class hardwood plain,solid,straight,chowkats and frames,wrought,framed rebated on the solid ,rounded or chamfered ,put together with glue pinned at joints.

S & F Flush shutters 35 mm thick, solid core construction, with block board core and plywood dace panels, commercial type on both sides incl provision of suitable blocks for taking mortice locks, latches or other fittings

S & F 2nd class H/W plain and skeleton shutters 35mm thick (any number of panels) with panels of timber particle board medium density wood panel both side feather edge or veenered particle board medium density wood particle board with commercial face complete specified in SSR Part-I, Section 1 Clause 8.20 (a).

S & F 2nd class H/W glazed and skeleton shutters 35mm thick open rebated and prepared to received glass, without (sash bars), edges of framing plain , chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I, Section 1 Clause 8.20 (a).

S&F 30mm thick glazed and skeleton shutters 2nd class hard wood , open rebated and prepared to receive glass, gauge etc divided into squares, with plain, cham-fered or rounded, mitred and rebated sash bars provided with stiles and rails as specified in SSR Part I ,section 8 clause8.20(b).

S & F 125 mm medium weight ,cold rolled mild steel butt hinges.

S & F 100mm medium weight ,cold rolled mild steel butt hinges.

S & F 75 mm medium weight ,cold rolled mild steel butt hinges.

S & F 50 mm medium weight ,cold rolled mild steel butt hinges.

S&F 150 mm mild steel pressed handles, oval type, stove enammeld black.

S&F 125 mm mild steel pressed handles, oval type, stove enammeld black.

S & F 150mm aluminium handles, cast type, anodised

S & F 100mm aluminium handles, cast type, anodised

S&F 300mm long aluminium alloy, anodised, sliding door bolt with clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed

S & F 200mm long aluminium anodised barrel tower bolts, extruded section and fixed

S & F 150mm long aluminium anodised barrel tower bolts, extruded section and fixed

S & F 100mm long aluminium anodised barrel tower bolts, extruded section and fixed

S & F 300mm MS ordinary rat tail rod pattern springs, incl roller plate complete

S & F Galvanized wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staples in repairs.

S & F for 3.00mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.50.m in each pane.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc.

Treating old cement concrete floor with brushing neat cement slurry with 3.0 Kg of cement per Sqm

M&L screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:4.

M&L for rendering 10 mm thick screed bed on fair faces of brickwork surfaces in CM 1:3 to receive wall finishes.

M&L Non-skid joint free coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceding 0.11sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as directed.

M&L coloured glazed ceramic tiles 200x 300x7 mm thick, in vertical surfaces, skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as directed.

M&L for 25 mm thick cement concrete type B-1, 1:2:4 (20 mm graded aggregate) to receive the top layer of tiles

M&L for 40 mm thick cement concrete type B-1,1:2:4(20mm graded aggregate) as in floor and making finished even and smooth with using extra cement.

M&L for 38mm width of strip glass dividing strip, 3mm thick and inserted in position

M & L including preparing surfaces of new wood and wood based materials, of any description , not otherwise described, over 10 cm width or girth, and treated with two coats of synthetic enamel paint over coat of pink primer.

M & L including preparing surfaces of new wood and wood based materials, of any description, not otherwise described, not exc 10 cm width or girth, and treated with two coats of synthetic enamel paint over coat of pink primer.

M & L including preparing surfaces of old wood and wood based materials, of any description , not otherwise described, over 10 cm width or girth, and treated with single coat of synthetic enamel paint over it.

M&L for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of redoxide complete all as specified

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of putty complete all as specified and directed.

Material and labour preparation of old plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including white wall putty (make-Birla/JK/Asian) on walls all as specified & directed.

Material and labour preparation of new plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including white wall putty (make-Birla/JK/Asian) on walls all as specified & directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement based paint complete all as specified and directed.

M&L for preparing newly surfaces of ceilings and applying three coats of white wash.

M&L for Preparing surface of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of creosote oil.

S&F in repair 15mm dia angle cock of PTMT any colour high pressure screwed for iron pipe and fixed.

S&F in repair 15mm dia stop cock of PTMT any colour high pressure screwed for iron pipe and fixed.

S&F in repair 20 mm dia stop cock of PTMT any colour high pressure screwed for iron pipe and fixed.

S&F in repair 15mm dia chromium plated bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe and fixed.

Dismantling water tanks of capacity exc 500 & nexc 1000 litres and removing to store.

S & F 1000 litre capacity ,rotational moulded polyethylene ISI marked water storage tanks (Cylindrical vertical with closed top) in position all specified in SSR Part –I Make : Syntex and Fusion

M & L Ball valves (20 mm) high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms/ 50mm-1240 gms)

S&F in repair 20mm dia gate metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F in repair vitreous China wash basin, white, flat back, size 630x450mm (flat back or angle back type) including brackets, cutting for and pinning 'in brackets waste coupling, waste pipe, grating complete

S&F in repair vitreous China wash basin, white, flat back, size 500x400mm (flat back or angle back type) including brackets, cutting for and pinning 'in brackets waste coupling, waste pipe, grating complete

Supply & Fix in repair vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including provision of lime concrete bedding, connecting to trap and flush pipe , man hol complete all as specified and as directed.

S&F Vitreous China wash down water closet pan (Pedestal pattern) white excluding fixing bolt incl plastic water closet seat cover and mild steel chromium plated or aluminised hinging device and jet spray complete fixed in repair.

S&F in repair, PVC L/L cistern 10 lir capacity, valveless, syphonic action type with float, handle incl 32mm dia flush pipe of polyethylene of low or high density or PVC & bracket etc complete including all as specified.

S&F in repair 125mm x 125mm for chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union etc

S&F in repair 15 mm dia bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed all as directed

S&F in repair PVC connections 15mm size with PTMT nuts of length 300/450mm

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

S&F PVC (SWR) floor trap 75 mm, setting and jointing with solvent cement

S & F 75mm bore PVC ( SWR) pipes single socketed ,in any length with rubber ring joints, fixed to wall.

S & F 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S & F PVC (SWR) bends of radius 75mm bore.

S & F PVC (SWR) junction single,(Single T) equal or unequal of radius 75mm bore.

S&F in repair PVC (SWR) vent cowl 75mm bore complete all as specified and as directed.

S & F 110MM PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S & F PVC (SWR) bends of radius 110mm bore.

S & F PVC (SWR) junction single,(Single T) equal or unequal of radius 110mm bore.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rein forced with M.S. square tube supplying and fixing in opening as per specification and drawing.

M&L for Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plaincolour PVC© channel PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock and bottom rail on either side as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded. Sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at site as per specification and drawing.

S&F Vitreous China Urinal, bowl type, of size 465 x 335x265mm white (back or corner wall type) complete incl providing and fixing plugs beding urinal against wall in cm 1:2 security urinal plug with and incl 60mm long brass screws pointing around urinal back in cement fixing automatically flushing cistern with bracket, flush pipes grating and union for discharge pipe complete.

S&F Vitreous China Urinal, Half stall type, white (back or corner wall type) complete incl providing and fixing plugs beding urinal against wall in cm 1:2 security urinal plug with and incl 60mm long brass screws pointing around urinal back in cement fixing automatically flushing cistern with bracket, flush pipes grating and union for discharge pipe complete.

M&L for R.C.C 1:2:4 type B1 (usig 20mm quoted agg) as slabs supported on walls, beams and columns in floors, roofs, landing, balconies, cover slabs complete all as specified and directed.

M&L for M.S. TMT bars 8 to 10 mm dia bent to shape required including cranking bending and binding with M.S wire not less than 0.9mm dia complete all as specified and directed.

Use and waste rough finished Form work to edges of concrete flats soffits of suspended slabs flat or batter such as roof slabs, floor slabs and similar work not exceeding 200 mm thick.

M&L for 75mm thick cement concrete type C-2,1:3:6(40mm graded aggregate) as in plinth protection ,footpath and making finished even and smooth without using extra cement.

M & L for plain cement concrete type-C2 1:3:6 (40mm garaded agg.) in surface channel and drains

M&L extra for forming fair finished drain or channel any girth in cement concrete using extra cement including forms, moulds mitred/stopped ends etc

S&F Fancy curtain rod 25mm dia with bracket, knobs, rings @ 10cm c/c etc complete all as specified. complete all as specified and as directed by Engineer-in-Charge

S&F powder coated aluminium snap grid frame work of size 605mm x 605mm for false ceiling including necessary notching. The snap grid shall consist of anodized aluminium main & cross Tee of size 36.5mm x 25mm x 1.4mm weighing 0.24 Kg/RM and 23.5mm x 26.4mm x1.40mm weighing 0.191Kg/RM respectively. The main and cross tee shall be jointed at junction crossing with anodized aluminium angle bracket of size 15mm x 15mm x 1.5mm weighing 0.12Kg /RM fixed with suitable MS bolts, nuts and washer. The snap grid (main /cross tee section) shall be supported at ends all along the wall with anodized aluminium angle of size 35mm x 25mm x 2mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement complete all as specified and directed by Engineer-in-charge.

S&F solid PVC wood grain printed sheet of 5mm thickinclusive of solvent cement and fixing at site on PVC frame as per specification and drawing

M&L Continuous brick edging with width equal to the length of the brick laid dry on edge vertically

S&F, 1mm thick wood grain printed PVC sheet fixed or laid on to flush doors by using rubber used adhesive, supplying & fixing at site as per specification

S&F 1st class HW Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, with all necessary labours; articles n exc 200 cu. cm each incl 50mm size butt hinges

S&F in Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixedof ISI marked complete all as specified and directed by Engr-in-charge.

Supply and fixing Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed with aluminium extruded section body

Supply and fixing 150 mm long Extruded brass handles, fabricated type polished complete all as specified

M&L Mild steel round bars as in window guard bars incl necessary welding and a shop coat of Zinc Primer, confirming to Fe-310-O or Fe-410-O.

S & F Anodized aluminum frame with powder coating for doors, windows, ventilators, Partitions with one or more rebates including joining cleat for fixing etc. complete all as specified.

M&L anodised aluminium window and ventilator shutterswith Powder Coating (minimum thickness of powder coating 50 micron) side hung type without sash bar aluminium section weighing 0.55kg/m including necessary jointing cleats glazing clips rubberneoprene packing handle 2 nos in each door, hinges, anodized snap beading screws aluminium anodised fitting such as peg stays 150mm long ( 2 nos) suitable handle (1 No) etc complete all as specified.

M&L one side obscured glass 5.5mm thick seleted quality fixed to aluminium frames and necessary rubber bedding required complete

Double action floor spring hydrically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover govering pivot made of brass other part made of mild steel heavy duty and fixed

S&F bright finished brass 100 mm mortice slatch and lock with four levers and pair of anodized (anodic coating 10 micron) as per IS-1868) aluminium lever handles with necessary screws etc complete as per directed by Engineer-in-Charge (Approved quality)

Cutting holes n.exe half brick wall thick in brick wall built in CM or lime mortar for inserted hold fast & making good disturbed surface in CM (1:3) or as required complete all as specified and as directed

M&L PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in bed block complete all as specified and as directed

M&L Vitrified ceramic tile10mm thick area of each tile not exc 0.36 sqm in floor set and jointed in neat cement slurry and point in white cement to match/ using coloured tile with border of different tile over 15mm screed in CM 1:6

M & L, viritfied ceramic tiles 10mm thick light shade (square or rectangular) area of each tile not .exceeding 0.36 sqm as in vertical surfaces like dado or skirting over 10mm thick in CM 1:3 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete.

M&L glazed ceramic coloured tiles, 450X 350X 7-8mm thick with highlighter as in vertical surfaces like dado or skirting over 10mm thick in CM 1:3 set & joined in neat cement slurry and pointed in coloured cement to match complete all as specified.

M & L for 2 coats of synthetic enameled paint over existing one coat of red oxide primer Zinc chrome including preparation of steel surface (Primer already done)

M&L complete removal of existing treatment and applying two coats of cement base paint paint on walls over a coat of primer complete all as specified and directed by Engineer-in-charge.

S&F stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for union 15mm dia and fixed in repair

S&F stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for union 20 mm dia and fixed in repair

S&F brass chromium plated tubular towel rail 20mm dia(D) type 60cm long between flanges complete.

Taking down of eves gutter,rain water pipes of any size or pattern including all fittings etc complete all as specified and directed.

S&F in repair stainless steel sink, 1.00 mm thick for kitchen with pluigs, waste pipe, washers including bedding in cement mortar on to dwarf wall or incl fixing cantilever brackets and connecting union etc overall size 495mm x 420xx with bowl size 410mm x 330mm x 160mm

M&L for granite slab green/ black colour as in cooking platform 18mm to 20mm thick over cement screed bed with pre grinding and mirror polishing/granite polishing and chamfering he corners to the entire satisfaction of Engr-in-Charge complete all as specified.

M&L for 12mm pre-laminated particle bopard, interior grade, pre-laminated one side with decorative choice laminated & other side balancing white laminated, fixed with screws to timber/steel frame work complete all as specified and as directed

S&F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to walll to make PVC frame as per specification and drawing all as specified by Engr-in-charge

M&L 50mm PCC 1:3:6 type C-1 using 20mm graded aggregate finished even and smooth without using extra cement as in plinth protection

M&L for precast cement concrete 1:2:4 typoe B1 using 20mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including neccesary formwork and set in CM 1:6 complete all as specified and as directed

E/M PORTION

Taking down carefully aluminium conductor point wiring (light, fan,socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and removing materials for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. to match with the existing complete all as specified.

M&L point wiring for light point/fan/bell controlled by one, one way switch using 1.5 Sq mm nominal cross sectional area multistranded FRLS copper conductor cable, PVC insulated sheathed drawn in and including PVC casing & capping of suitable size with fittings complete fixed to wall/ceiling including PVC closed recessed boxes of required size factory made for mounting of switches/sockets/regulators/bell push etc and1.5 Sq mm nominal cross sectional area multistranded FRLS copper conductor PVC insulated sheathed earth wire and connecting to earth dolly by means of screws, washers etc. complete all as specified.

M&L point wiring for light point/fan controlled by one, two way switch using 1.5 Sq mm nominal cross sectional area multistranded FRLS copper conductor cable, PVC insulated sheathed drawn in and including PVC casing & capping of suitable size with fittings complete fixed to wall/ceiling including PVC closed recessed boxes of required size factory made for mounting of switches/sockets/regulators/bell push etc and1.5 Sq mm nominal cross sectional area multistranded FRLS copper conductor PVC insulated sheathed earth wire and connecting to earth dolly by means of screws, washers etc. complete all as specified.

M&L wiring for one 3 pin socket outlet 5 amps on independent board using 1.5 Sq mm nominal cross sectional area multistranded FRLS copper conductor cable, PVC insulated sheathed drawn in and including PVC casing & capping of suitable size with fittings complete fixed to wall/ceiling including PVC closed recessed boxes of required size factory made for mounting of switches/sockets etc and1.5 Sq mm nominal cross sectional area multistranded FRLS copper conductor PVC insulated sheathed earth wire and connecting to earth dolly by means of screws, washers etc. complete all as specified.

Ditto all as Ser No 158 above but for 5 Amps socket point on same board with other switches.

M&L wiring for one 3 pin socket outlet 15 amps on independent board using 2.5 Sq mm nominal cross sectional area multistranded FRLS copper conductor, PVC insulated sheathed cables in and including casing & capping of suitable size with fittings complete fixed to wall/ceiling including PVC closed recessed boxes factory made for mounting of switches/sockets etc and 2.5 Sq mm nominal cross sectional area multistranded copper conductor PVC insulated FRLS sheathed earth wire and connecting to earth dolly by means of screws, washers etc. complete all as specified.

S&F Polycarbonate Switch piano flush type, SP, 6 Amps, one way complete all as specified.

S&F Polycarbonate Switch piano flush type, SP, 6 Amps, two way complete all as specified.

S&F Polycarbonate socket out let 2 in 1 socket 5 pin, (6 Amps) flush type controlled by one switch, complete all as specified.

S&F Polycarbonate switch socket out let 2 in 1 socket 5 pin, 5&15 amps flush type controlled by one 15 Amps switch, complete all as specified.

S&F ceiling fan regulator electronic type 240 volts ISI marked 5 steps and connecting all as specified.

Supply and fix in replacement wall mounted LED batten extruded aluminium heat shrink provided for efficient heat dissipation and integrated electronic driver lamp type 20 watts 6000K 4 feet complete all as specified.

S&F lamp holder, insulated body, angle holder pVC/Polycarbonated type with back plate complete all as specified.

S&F in replacement of 10 watt LED new adore 10WB22 cool day light ball lamp.Ordering code complete all as specified and as directed

S&F LED bulk head 10 watts 6000K with opal diffuser including making electrical connection complete all as specified and as directed

S&F ceiling rose surface bakelite 65x50mm two to three terminals complete all as specified and as directed

S&F in replacement sheet metal enclosure MCB DB double door 8 ways with 200 Amps rated bus bar SPN complete all as specifed and direcetd.Make:Havells/Legrand/Standard

S&F in replacement sheet metal enclosure MCB DB double door 4 ways with 200 Amps rated bus bar SPN complete all as specifed and direcetd.Make:Havells/Legrand/Standard

S&F MCBs 6-32 amps rating and to be housed in DBs catered here in before complete all as specified and directed.Havells/Legrand/Standard (Note :- Proper and suitable size cable lugs to be fixed with MCBs are deemed to be included in unit rate of each MCB of any rating)

Ditto all as Ser No 173 above but single pole and neutral 6-32 Amps B series socket point on same board.

Material and labour in repairs for fan hook made out of mild steel flat iron of size 40mm x 5mm and 66 cm long including taking down old unserviceable fan hook, complete all as specified and directed.

Material and labour for house service bracket (hook type) complete with 3 mtrs long GI pipe 40mm dia, medium grade, 2 Nos 90 degree MS hook and stay or gay on the wall by grouting cement mortar and make good on all disturbed surfaces complete all as specified and directed.

Material & Labour for one twin core cable flat or circular, 1100 volts grade heavy duty cable, PVC insulated, with stranded aluminium conductor, size 10 Sqmm served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating in service hangers not more than 1 metre apart including 4mm GI suspension wire, and including taking down of unserviceable service connection complete all as specified and directed.

Material & Labour for 1100 volts heavy duty cable , PVC insulated, with stranded aluminium conductor, size 16 Sqmm served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating in service hangers not more than 1 metre apart including 4mm GI suspension wire, and including taking down of unserviceable service connection complete all as specified and directed.

Supply and fixing exhaust fan heavy duty 300mm 4 blade, AC single phase 240 volts 900 RPM with louver shutter on wall with necessary electrical connections with 3 core copper flexible multistranded cable of suitable size and connecting with ceiling rose including making hole/niche in wall to fix the fan and necessary arrangement for fixing such as frame,nuts,bolts and washers all as required at site and directed by Engr-in-Charge.

M & L for submain wiring with two runs of FRLSH PVC insulated multistranded, copper coductor of size 6 Sqmm cable single core 1100 Volts Grade and one run of earth continuity conductor cable of 6 Sq mm solid strand cable drawn in and including FRLSH PVC casing caping of suitable size alongwith aceessories complete all as specified and as directed. Note:- 2 run of 6sqmm cable & 1 run of 4sqmm earth wire and one run of casing capping shall be measured and paid as one length.

M & L for submain wiring with two runs of FRLSH PVC insulated multistranded, copper coductor of size 4 Sqmm cable single core 1100 Volts Grade and one run of earth continuity conductor cable of 4 Sq mm solid strand cable drawn in and including FRLSH PVC casing caping of suitable size alongwith aceessories complete all as specified and as directed. Note:- 2 run of 4sqmm cable & 1 run of 4sqmm earth wire and one run of casing capping shall be measured and paid as one length.

Taking down old/defective ceiling fans of any size/sweep and transproting these to MES store yard for deposit complete all as specified

Supply & fixing ceiling fans 1200mm sweep complete including provision of PVC insulated copper multi starnded three core flexible cable for making necessary electrical connections from ceiling rose to connector all as required at site.

M & L Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common saft filling in alternate layers and electrode connection by using earth lead GI wire 4mm dia by means of bolts, nuts, check nuts and washers made of galvanised iron and thimbles and other end of the earth wire connected to main switch board protected by galvanised iron light grade pipe 15mm bore in wall/floor/and GI Pipe 20mm bore light grade for watering with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC pit cover including necessary excavation and earth work in any type of soil, returning slurry approved soil and disposed of surplus soil to a distance not exceeding 50 Mtr away all as shown in Electrical Plate No 3 of SSR 2009( Part-I) incl dismantling of exsisting earthing.

S&F Bell push, flush type, 5 amp complete all as specified and as directed

S&F Bell, AC, 230 volts, single pole complete all as specified and as directed

M&L single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps including making necessary electrical connections all as required at site.

S&F of metal clad socket single pole and neutral enclosure with a two pin and earth plug top and sc\ocket complete with one single pole MCB 415 volts 20/32 Amps complete all as specified and directed

M&L in replacement mounting bracket made out of 40 mm dia GI pipe medium grade 120 cm long cut to size and bend to shape , fixing on poles with flat iron clamps 40mm x 6 mm – 02 sets including nuts, bolts and washers including one coat of aluminium pait over acoat of red oxide primer including taking down of old unserviceable complete all as specified.

Supply and Fixing in replacement New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP65 roadway luminaire with high power LEDs as light source & exclusively designed polycarbonate cover alongwith electronic driver. suitable for 43 mm dia bracket size ( max) of rating 45W LED including connecting with 3 core aluminium conducor 2.5sqmm with Overhead conductors or UG Cables complete all as specified and directed

M/S JALALUDDIN AHMED

M/S L N ENTERPRISE

M/S LAKSHMI ENTERPRISES

M/S Yadav Corporation