Upgradation of FW Sub Centre Nediyara, CHC Anchal

Amount

Civil work

13.98.1 : Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:One or more coats on old work

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

13.99.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work

50.10.1 : Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

50.10.2 : Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

12.50 : Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

od207023/2023_2024 : Providing and fixing 8'' UPVC Aqua pathy ( Gutter) with M.S clamp all complete as per direction of Engineer-in-Charge.

9.48.1 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.1.3 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

2.1.1 : Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed:All Kinds of soil

16.68 : Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

od207170/2023_2024 : Providing Semi Executive chair high back revolving chair with multifunction mechanism (Brand- Godrej))as per direction of Engineer-in-charge.

od207125/2023_2024 : Providing Airport type steel metal chair 3 in 1 (3 seater) ( brand-Nilkamal-stainless steel)as per direction of Engineer-in-charge.

od207140/2023_2024 : Providing Rectangular modular work station using 18 mm both side laminated MDF on table top and sides ,drawyers, keyboard drawyers etc and 8 mm thick frameless toughened glass are side pannels and the edges are finishing with teak wood lipping ,providing telescopic channel on keyboard tray ,Cable manager provision for CPU/UPS/Auto close heavy duty hinges drawyers wooden leg rest and providing handles , locking arrangements etc. complete.Rectangular work station (1.50x0.75x0.75 m)

od207142/2023_2024 : Providing office visitors chair ( brand-Nilkamal)as per direction of Engineer-in-charge.

od209495/2023_2024 : Supplying and fixing storage cupboard (GODREJ) size 1.00x0.50x1.90 m

od209467/2023_2024 : Providing IUCD Table with two fold cushion of size 1.90x0.90x0.60 m of approved brand

Electrical item

1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

od209485/2023_2024 : Supplying and fixing LED Tube set (Electronics) and other accessories

od209486/2023_2024 : Supplying and fixing 48" Ceiling fan and other accessories

Bidder Name

RAJAN N (MAHALEKSHMI CONSTRUCTIONS)