UPGRADATION/ IMPROVEMENT OF BUILDING NO P-99 AT AF STN BARRACKPORE (PHASE-I) UNDER GE (AF) BARRACKPORE

Taking down cement plaster of any description built in cement mortar on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc. and removing debrish from site complete all as specified and directed.

Demolition of brick work or stone boulder masonry, built in cement mortar including all quoins, arches, pillars etc. including removing of unserviciable material from site complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided including removing of rubish from site complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided including reinforcement cut as required to facilitate demolition and removing debries from site of work completeall as specified and directed.

Dismantling of timber scantling 40 Sqcm and over in section, in any position in framed work and removing materials from site of work complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for and removing materials from site of work complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Dismantling of stone slabs and tiles laid dry of any description or thickness in floors, aprons etc. complete all as specified and directed.

Taking down chowkats or frames with shutters n.exc. 1.50 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames with shutters exc. 1.50 sqm but n.exc 4.00 sqm each (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutters of any description exc. 1.00 Sqm but n.exc. 2.00 Sqm each complete all as specified and directed.

Taking down wooden door/window of area n.exc 4.00 sqm each carefully and refixing in the same opening after necessary repair such as stay handle etc and making good to existing surface with cement mortar (1:3) complete all as specified and directed. Note:- Concrete required for fixing hold fast shall be included in quoted rate.

Taking down chowkats or frames with shutters exc. 1.50 sqm but n.exc 4.00 sqm each (without taking off shutters from the frames) and refixing in same opening with using hold fast, minor cement concrete work and making good complete all as specified and directed.

Material and labour for 15mm thick rendering in cement mortar (1:4) on fair faces of brick work in two layers, first layer of 10mm thick and top layer of 5mm thick with using liquid water proofing coumpound (WPC) @ 200ml/50Kg bag or as per manufacturers instruction and finish the surfaces even and smooth without using extra cement as in wall complete all as specified and directed. Note : WPC will be measured and paid separately under respective item.

Material and labour for 10mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar (1:6) and finish the surfaces fair and even on wall complete all as specified and directed.

Material and labour for 5mm thick rendering on concrete surfaces in cement mortar (1:3) and finish the surfaces even and smooth without using extra cement in ceiling complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of acrylic washable distemper over a coat of alkali resistance primer including applying 1mm thick wall care putty complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of wall and applying three coat of white wash complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed.

Materials and labour for complete removal of existing treatment of old decorated surfaces of walls and applying two coats of acrylic washable distemper over a coat of alkali resistance primer including applying 1mm thick wall care putty including preperation of surface complete all as specified and directed.

Material and labour for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of old decorated surfaces of wall and applying one coat of white wash complete all as specified and directed.

Material and labour for preparation of old decorated surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

Material and labour for PCC (1:2:4), type B1, (using 20mm graded stone aggregate), as in coping, bed plate, kerbs, water troughs and like including weathering, slightly rounded or chamfered angles and throating, including necessary formwork complete all as specified and as directed

Material and labour for brick work with sub class `B` bricks, old size, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

Materials and labour for half brick thick brick work with sub class `B` bricks, old size, straight or curved on plan to any radius built in cement mortar (1:4) complete all as specified and directed.

Material and labour for well-seasoned 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

Material and labour for well-seasoned 2nd class hard wood plain fillets, square, rectangular or triangular in section, wrought, secured with nails or brads, sectional area exc. 13 sqcm but not exc. 25 sqcm including taking down existing fillets complete all as specified and directed.

Supply and fix 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers as specified in SSR Part-I, Section 8, clause 8.24 (a) and fitted to chowkats complete all as specified and directed.

Supply and fix factory made 30mm thick flush shutters, solid core construction, with block board core both faces are covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

Removing old paint by paint removers or burning off by blow lamps and cleaning with scrapers, any number of coats, any width or girth complete all as specified and directed.

Supply and fix 1mm thick veneered decorative plywood, grade1 (with BWR resin) with decorative face veneers on one face; fixed with adhessive of first quality to flush door shutter or to timber framework etc. complete all as specified and directed.

Supply and fix factory made 30mm thick second class hardwood plain framed panelled shutters (any numbers of panels) with panels of timber flat both sides (feather edged) or of veneered particle board medium density, wood particle with commercial face veneers including framing is moulded on solid (for each side) and fitted to chowkats complete all as specified and directed.

Supply and fix powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and directed.

Supply and fix powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and directed.

Supply and fix anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and directed.

Supply and fix mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders, framed balusters, walk ways; railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Supply and fix stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

Supply and fix in repair solid PVC wall lining consisting of 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC/Aluminium frame complete all as specified and directed.

Material and labour for second class hard wood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n. exc 200 cu. cm each complete all as specified and directed.

Suplly and fix 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

Suplly and fix stainless steel 100mm size butt hinges, medium weight complete all as specified and directed.

Suplly and fix 150 mm long aluminum anodised barrel tower bolts cast type complete all as specified and directed.

Supply and fix 100mm long aluminium handles, cast type, anodized complete all as specified and directed.

Supply and fix 300mm long aluminium alloy, anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

Supply and fix in repair 300mm long aluminium alloy, anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

Supply and fix in repair mild steel 300mm long ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

Supply and fix 5.50 mm thick sheet glass ordinary quality and glazing with oil putty or wooden/ aluminium bead/ rubber beads, nails etc in square n. exc 0.5 sqm in each pane complete all as specified and directed.

Supply and fix 5.50 mm thick sheet glass ordinary quality and glazing with oil putty or wooden/ aluminium bead/ rubber beads, nails etc in square exc 0.5 sqm in each pane complete all as specified and directed.

Supply and fix 4 mm thick figured glass pin head type and glazing with oil putty in square n. exc 0.5 Sqm in each pane complete all as specified and directed.

Supply and fix stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Material and labour for RCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Material and labour for mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed.

All as per item No 55.00 above but 6mm to 8mm dia and -ditto-.

Material and labour for form work to sides and soffits of floor or roof beams, beam haunchings, girders, bres-summers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. with rough finished flat surfaces of concrete complete all as specified and directed.

Material and labour for pre-cast RCC (1:2:4) type B1 (using 20 mm graded stone aggregate) in landings, cover slabs, chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and set in cement mortar (1:4) including demolition of reinforced concrete (reinforcement cut as required to facilitate demolition) and removal of rubbish from site complete all as specified and directed.

Material and labour for vitrified ceramic tiles (light shade) (premium quality) 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 20mm thick screed bed in cement mortar (1:6) complete all as specified and directed.

All as per item No 59.00 above but in skirting and dado laid over and including 10mm thick rendering in cement mortar (1:4) and -ditto-.

Material and labour for ceramic, non skid coloured tiles (premium quality) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exc. 0.18sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified and directed.

Material and labour for glazed ceramic tiles of size 300x450x7-8 mm (premium quality) coloured in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10mm thick cement plaster in cement mortar (1:4) complete all as specified and directed.

Material and labour for 20mm thick jet black granite for top shelves (of any type) work (table rubbed and polished) in cupboard shelves, steps, jambs, window cills, cooking platforms and like in cement mortar (1:4) including pointing, grooving to wall etc with white cement using marble dust with admixture of pigment to match with shade of granite including moulding/nosing fixed independently complete all as specified and directed.

Material and labour for Makrana white marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

Material and labour for machine cut cudappah stone slab 20-25mm thick as in shelf including rubbing and polishing complete including taking down existing shelf complete all as specified and directed.

Material and labour for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Material and labour for 75mm thick PCC (1:3:6) type C-1 (using 20mm graded stone aggregate) as in plinth protection including finishing the concrete surface even and smooth with using extra cement complete all as specified and directed.

Material and labour for forming 12 mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘B’, thickness of concrete slab in 75mm complete all as specified and directed.

Supply and fix 15 mm bore steel tubes medium grade, galvanised, with all fitting and fixed to walls, ceilings, roofs or laid in floors complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, including removal from site complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, including removal from site complete all as specified and directed.

Supply and fix 20 mm bore steel tubes medium grade, galvanised, with all fitting and fixed to walls, ceilings, roofs or laid in floors complete all as specified and directed.

Supply, hoist and fix 1000 litre capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of old unseviciable existing tank and removing from site complete all as specified and directed.

Disconnecting existing tanks of capacity exc 500 ltrs and n. exc 1000 ltrs including float valve, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

Material and labour for cutting chases, pinning in brick wall making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing and making good, cutting not exc 10 cm girth complete all as specified and directed.

Supply and fix in repair 15mm bore stop valves, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

Supply and fix in repair 15 mm bore two way bib taps fancy type cast copper alloy chromium plated with crutch or handles screwed down, screwed for iron pipes complete all as specified and directed.

Supply and fix in repair 15mm bore fancy type, chromium plated, bib tap, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified and directed.

Supply and fix in repair 15mm bore fancy type wall mixer chromium plated, brass, round headed single liver with extruded brass made spindle and housing with wall flange, screwed down high pressure with long screwed shanks, screwed for iron pipe complete all as specified and directed.

Supply and fix in repair 15mm bore angle cock fancy type cast copper alloy chromium plated with crutch or handles screwed down, screwed for iron pipes as fixed complete all as specified and directed.

Supply and fix in repair PVC connection pipe 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

Supply and fix in repair brass chromium plated shower rose 125mm size with or without swivel joint complete all as specified and directed.

Supply and fix in repair 15mm bore fancy type pillar tap cast copper alloy, chromium plated, swan neck type screwed down high pressure with long screwed shanks, screwed for iron pipe complete all as specified and directed.

Supply and fix in repair 125mm PTMT grating doom (minimum weight 40gms) complete all as specified and directed.

Supply and fix in repair 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe complete all as specified and directed.

Supply and fix in repair vitreous china wash down water closet pan (pedestal Pattern) white (excluding fixing bolts flusing cistern and flush pipe) including connection to drain (or out going pipe) and to flush pipe anti syphonage pipe including cast iron P or S trap fixed on floor complete all as specified and directed.

Supply and fix in repair plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Supply and fix in repair vitreous china wash hand basin, white, flat back, size 550x400mm excluding taps, waste pipe, chain & plug and porcelain stopper but with brackets and 32 mm bore brass waste fittings chromium plated including cutting for and pinning in ends of brackets complete all as specified and directed.

Supply and fix in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Supply and fix in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

Supply and fix in repair telephonic hand shower chromium plated with 1.50 meter flexible tube (CP) with CP wall hook of any colour for fixing with 15mm bore pipe complete all as specified and directed.

Supply and fix in repair toilet paper holder, brass, chromium plated, fixed with stainless screw complete all as specified and directed

Supply and fix in repair CP basin mixer for mixing hot and cold water screwed down for pipes suitable for 15mm dia pipe complete all as specified and directed.

Supply and fix in repair 40mm bore high density polyethylene pipes (HDPE) with all fittings of pressure rating 6 kgf/sqcm fixed to walls, ceilings or in floors etc. complete all as specified and directed.

Supply and fix in repair 25 mm dia aluminium anodised decorative/fancy type drapery rod with bracket complete all as specified and directed.

Dismantling of 110/100/75mm dia PVC/ cast iron or reinforced concrete drain pipes with all fittings, jointed in cement mortar and taking out of trenches/ from wall, if required complete all as specified and directed.

Supply and fix solid PVC door frame of size 50x47 mm made out of 5mm PVC sheet plain colour reinforced with MS square tube as per specification and drawing given in SSR Part-II 2020 complete all as specified and directed.

Supply and fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement as per specification and drawing given in SSR Part-II 2020 complete all as specified and directed.

Supply and fix factory made PVC wire gauzed door shutters 30mmm thick (style) consisting of frame made of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20 mm width Stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of wire gauzed shutter, the wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly and jointed together with solvent cement as per specification and drawing given on MES schedule Part – II (2020) complete all as specified and directed.

Material and labour for cutting holes into or through brick wall built in cement mortar of superficial area not exc 150 sqcm and making good in CM (1:3) or cement concrete (1:2:4) type B-1 as required complete all as specified and directed.

Cutting holes into or through brick walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required superficial area exc 400 sqcm but not exc 0.10 Sqm complete all as specified and directed.

Material and labour for welding in repairs n. exc 2.5cm in length, thickness of metal to be welded exc 6mm but n. exc 9mm complete all as specified and directed.

Supply and fix 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls including stack clamp of suitable size complete all as specified and directed.

Supply and fix 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

Fixing only in repair 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls including stack clamp of suitable size complete all as specified and directed.

Supply and fix 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls including stack clamp of suitable size complete all as specified and directed.

Supply and fix 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

Supply and fix 110mm bore PVC (SWR) juction single (single T) equal or unequal with access door complete all as speified and directed

Supply and fix 110 mm bore PVC (SWR) bends with access door any radius complete all as speified and directed.

Supply and fix 75 mm bore PVC (SWR) bends any radius complete all as speified and directed.

Supply and fix 75mm bore PVC (SWR) juction single (single T) equal or unequal complete all as speified and directed

Supply and fix in repair 75 mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

Supply and fix in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

Supply and fix in repair 32 mm bore PVC corrugated waste pipe 800mm long complete all as specified and directed.

Supply and fix in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

Supply and fix in repair towel ring of CP fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 90gms) complete all as specified and directed.

Supply and fix in repair 20mm dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

Supply and fix in repair 5mm thick glass corner shelf of size 300 x 300mm with stainless steel railing fixed with chromium plated screws complete all as specified and directed.

Supply and fix in repair soap dish, brass, chromium plated complete all as specified and directed.

Complete removal of existing roof treatment in any layers and disposal of debris from site complete all as specified and directed. Notes: - (a) The rates are inclusive of removal for any type of old water proofing treatement over main RCC slab. (b) Bidders are advised to visit the site and esure about site condition before quoting their rates. (c) Demolition of PCC/ taking down plaster if any shall be measured and paid saparately under respective items.

Material and labour for 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in roof top complete all as specified and directed.

Material and labour for 5mm thick rendering in cement mortar (1:3) with using water proofing coumpound (WPC) @ 200 ml per bag of cement (50 Kg) or as per manufacturers instruction on roof top while concrete is green to become integrated part of concrete padding layer and finish the surfaces even and smooth without using extra cement complete all as specified and directed. Note : WPC will be measured and paid separately under respective item.

Material and labour for 15mm thick rendering in cement mortar (1:4) with using water proofing coumpound (WPC) @ 200 ml per bag of cement or as per manufacturers instruction on roof top and finish the surfaces even and smooth without using extra cement including taking down existing cement plaster and disposal of debris from site complete all as specified and directed. Note : WPC will be measured and paid separately under respective item.

Supply only liquid water proofing compound (WPC) complete all as specified and directed.

Material and labour for water proofing treatment to RCC roof surface comprising with the following course of treatment/specifications from bottom to top :- (a) Applying cold bituminous primer @ 0.30 liters per sqm confirming to IS 3384 over plastered surfaces of roof. (b) One layer of APP based polymeric membrane 3mm thick, weight not less than 3.50 kgs per sqm, reinforced with non woven polyester matt central core fabric (weight not less than 160 GSM) and coated on both side with and including layer of APP modified bitumen and finished with and including micro-prefabricated heat fusible polythene film on both surfaces. (c) Finally applying two coats of bituminous aluminum paint @ 0.10 ltrs per sqm per coat on top surface. Note:- (i) Laying of APP based polymeric membrane shall be done by torch on method or as per manufacturers instructions. (ii) A minimum overlap of 150mm and 100mm should be made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as per manufacturers instructions. (iii) The work shall be executed only through authorised applicator of manufacturer as approved by GE. Make of APP membrane:- Super Thermolay of M/s STP Ltd, Hyperplas of M/s IWL India Ltd, Hydrostop of M/s Tiki Tar Danosa (India) pvt ltd, , M/s FOSROC Chemicals, Smartcare APP membranes of M/s Asian Paints Ltd.

Material and labour for post constructional anti-termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. .complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store for keeping in safe custody for reuse complete all as specified and directed.

Material and labour for light/fan point wiring (concealed type) with single core PVC insulated unsheathed multistranded FRLSH copper conductor cable of 1100 volts grade size 1.5 sqmm (nominal area) in and including 20mm dia heavy duty rigid non metalic PVC conduit with accessories including modular flush metal boxes with inner and outer modular cover plates for housing switches, sockets and regulators with all fittings and fixing materials with one single core PVC insulated unsheathed 1.5 sqmm (nominal area) multistranded FRLSH copper conductor as earth continuity wire and connected to earth dolly complete all as specified and directed. Note: (a) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for Each individual circuit from the distribution board. (b) Quoted rate shall be included for cuttings /chasing the wall and making good disturbed surfaces to fix PVC conduit and flush metal box. (c) Modular cover plate with frame shall be measured and paid seperately under respective items.

All as per item No. 130.00 here-in-before but for bell/buzzer point controlled by one push button on independent board and -ditto-.

All as per item No. 130.00 here-in-before but for one five pins 5 Amps switch socket outlet point on independent board and -ditto-.

All as per item No. 130.00 here-in-before but for one light point controlled by two 2-way switches of 5 amps and -ditto-.

All as per item No. 130.00 here-in-before but for one five pins 5 Amps socket outlet point on same board and -ditto-.

All as per item No. 130.00 here-in-before but for 15 amps socket outlet on independent board with 2.5 sqmm PVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts grade including 2.5 sqmm PVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts grade as earth continuity conductor and connecting to common earth dolly and -ditto-.

Supply and fix modular switch 1 way 6 amps, 1 module complete all as specified and directed

Supply and fix modular switch 2 way 6 amps, 1 module complete all as specified and directed

Supply and fix modular switch 1 way 16 amps, 1 module complete all as specified and directed.

Supply and fix modular bell push 6 amps, 1 module complete all as specified and directed.

Supply and fix modular shuttered sockets 6 amps, 3/5 pin combined two module complete all as specified and directed.

Supply and fix modular shuttered sockets 6/16 amps, 3/5 pin combined two module complete all as specified and directed.

Supply and fix modular fan regulator step type 120W, 2 module complete all as specified and directed.

Supply and fix modular white cover plate with frame of 1/2 module complete all as specified and directed.

Supply and fix modular white cover plate with frame of 3 module complete all as specified and directed.

Supply and fix modular white cover plate with frame of 8 module complete all as specified and directed.

Supply and fix modular white cover plate with frame of 6 module complete all as specified and directed.

Supply and fix in repair LED tube light fitting 1 x 20W (+/- 5%), 220V, AC with extruded strip in thermally conductive material & extruded housing in optically efficient material milky white with system lumen efficacy > 120 lumen per watt minimum system 2300 - 2400 and chip, Integrated electronic driver, SMD based LED constant current supply with double sided connection to avoid short circuit and surge protection greater than 2.5 KV, IP 20 protection and CRI>80, Power factor > 0.95, THD less than 15%, correlated Colour temperature (CCT) of 6500K, Operating Voltage of 140 V to 270 V, frequency of 50Hz burning hours 50000 hours with comprises of CRCA pre coated metal housing complete all as specified and directed.

Supply and fix in repair LED lights fittings with extruded aluminium housing, high quality PC diffuser, efficacy- 100lm/W, 10 watt, 220V, AC, 6500K, CRI ≥80, 2 feet long, integrated design including connecting up with flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fix ceiling rose, 3 terminals, fabricated of PVC/Polycarbonate, isolated body complete all as specified and directed.

Supply and fix in repair MCB TPN, 415 Volts, 40 to 100 amps, "C" series, breaking capacity 10 KA complete all as specified and directed.

Supply and fix 300mm sweep steel body exhaust fan AC single phase 230/240 volt. 1400 RPM, heavy duty, ISI marked, along with metal blade powder coated metalic finish with GI sheet louvers, low noise including necessary electric connection with and including cutting/making opening having dia of the hole for 300mm sweep exhaust fan in any type of walls of any description with nut, bolt, washer and making good distrubed surfaces complete all as specified and directed.

Supply and fix in repair sheet metal enclosure SPN DB 8 ways double door having facility to fix MCB in incomer and MCBs in outgoing, metal door IP-43 type complete fitted with bus bars, neutral links, blanking plates complete all as specified and directed.

Supply and fix in repair sheet metal enclosure TPN DB 4 ways double door having facility to fix MCB in incomer and MCBs in outgoing, metal door IP-43 type complete fitted with bus bars, neutral links, blanking plates complete all as specified and directed.

Supply and fix in repair MCB SPN, 240 Volts, 40 amps, "C" series, breaking capacity 10 KA complete all as specified and directed.

Supply and fix in repair MCB SP, 240 Volts, of 6 to 32 amps current rating, 10 KA breaking capacity "C" series complete all as specified and directed.

Supply and fix ceiling fans complete with blades, down rods, and accessories, 230 V, 1200 mm sweep. minimum air delivery 210 CFM with service value 6.00 BEE. 5 star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Taking down electric meter from inside room and refixing the meter with necessary electrical connection near main door in proper mannar including thermoplastic polystrene of IP 65 single metering cover wall mounted of size 217x253x115 mm with transparent glass and necessary fixing nut bolt and clamp for intallation of single/three phase meter including connection & suitable writing of Qtr Number on meter Box by paint complete all as spcified and directed

Taking down electric water heater from bathroom room and refixing the same after finishing of bathroom with fixing nut & bolt if required complete all as spcified and directed. Note - Contractor kept the water heater in safe custody for reuse and if any damaged found contractor replaced with new one without any extra cost.

Material and labour for concealed submain wiring comprising single core , 2 run of 4 sqmm nominal cross sectional area, FR-LSH multistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade drawing in and including appropriate dia. in PVC conduit and its fittings complete including provision of 1run of 4 sqmm nominal cross sectional area, FR-LSH multistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade as earth wire complete including taking down old unserviciable sub main wiring complete all as specified and directed. Note :- (a) Cost for extra length of cables / wire required for connection to MCBs/DB's shall be included in quoted rates. (b) Cost for cuttings /chasing of wall etc and making good the disturbed surface shall be included in quoted rates.

Material and labour for concealed submain wiring comprising single core , 2 run of 6 sqmm nominal cross sectional area, FR-LSH multistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade drawing in and including appropriate dia. in PVC conduit and its fittings complete including provision of 1run of 6 sqmm nominal cross sectional area, FR-LSH multistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade as earth wire complete including taking down old unserviciable sub main wiring complete all as specified and directed. Note :- (a) Cost for extra length of cables / wire required for connection to MCBs/DB's shall be included in quoted rates. (b). Cost for cuttings /chasing of wall etc and making good the disturbed surface shall be included in quoted rates.

Material and labour for earthing complete with GI earth plate electrode of size 600x600x6 mm thick buried directly in ground with earth pit not less than 2.25 meter deep below ground level with top edge of plate not less than 1.5 meter below normal ground level connected to GI wire 4 mm dia earth lead by means of nuts, bolts, check nuts, washers of galvanized iron as steel, protected by 15mm dia GI pipe (medium grade) including cement concrete (1:3:6) type C-1 earth pit with precast RCC (1:1.5:3) type A-1 cover slab of size 42 x 42 x 6 cm thick reinforced with 8mm dia TMT bars @ 15 cm c/c both ways with 10mm dia mild steel round bar of 30 cm long, bent to shape as lifting handle, funnel, wire mesh, 20 mm bore galvanized iron pipe (medium grade) for watering, earth testing point, charcoal or coke and salt in alternate layers with necessary earth work in soft/loose soil complete all as shown in electrical plate No 3 of SSR Part I including testing on completion complete as specified and directed. Note:- GI wire upto 7.5m including testing shall be included in qouted rates.

Material and labour for earth continuity conductor or main earthing lead with 4mm dia GI wire, fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or DB's / Indoor type LT PBs or any other indicated situation for loop earthing etc complete all as specified and directed