CONSTRUCTION OF PROPOSED 200 BEDDED MOTHER AND CHILD CARE WARDS IN DISTRICT HOSPITAL, HARIDWAR

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.: All kinds of soil Earth work 1.5 m - 3.0 m

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.: All kinds of soil Earth work 3.0m - 4.5 m

Open timbering over areas including strutting, shoring etc. complete.Depth exceeding 3 m.

Providing and erecting 2.00 metre high temporary barricading at site; each panel of size 2.50mx2.00m made of 40x40x6mm angle iron or 50x50x3mm hollow MS tube posts/horizontal members/ bracings covered with 1.63mm thick MS sheet. The sheet shall be fixed with 30x5mm MS flat by suitable welding/riveting. The panels shall be made so that gap of 50cm above the ground is available making overall height as 2.5m. MS channel ISLC 75 @ 5.70 kg/m, 50cm long shall be provided at the bottom having oval shaped holes of size 50x25mm at both ends with 50cm long MS angle 40x40x6mm bracing. Suitable arrangement shall be made to fix the barricading to avoid from overturning by providing 250mm long expansion fasteners at both ends. The work shall be executed as per drawing/direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge.

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete : Serrated with central bulb (300 mm wide)

Carriage of material by Mechanical Transport including loading,unloading and stacking etc complete lead 10-15 Km.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete.1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness),including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering,shuttering, finishing and reinforcement, including admixtures inrecommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works upto plinth level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge .All works above plinth level upto floor V level

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. All works upto plinth level

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. All works above plinth level upto floor V level

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centring and shuttering including strutting,ropping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centring and shuttering including strutting,ropping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in :cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Extra for concrete work in superstructure above floor V level for each four floors or part thereof.

Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means.

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means

Supply and installation ,Testing and Commissioning of FIRE RATED DOOR tested for 2 hours all included frame thicknes 100*58 mm, frame sheet thickness 1.2 mm with Rockwool infill, Door leaves sheet thickness 0.8mm skin pass galvanised iron sheet with honeycomb Kraft paper infill, leaf thickness 46mm, door stopper, door closer, Ball bearing butt hinge of size 102*75*3mm with SS screw, Mortise dead bolt lock with euro profile, door stopper, door closer, Fire rated clear glass 200*300*6mm, D handle both side 19*254 mm, double shutter, with 300 mm ventilator, including installation etc. complete in all aspects as per direction of Engineer in Charge. (Make- Tata Pravesh) D10 opening size 1500*2400 Emergency door with panic bar

Supply and installation ,Testing and Commissioning of FIRE RATED DOOR tested for 2 hours all included frame thicknes 100*58 mm, frame sheet thickness 1.2 mm with Rockwool infill, Door leaves sheet thickness 0.8mm skin pass galvanised iron sheet with honeycomb Kraft paper infill, leaf thickness 46mm, door stopper, door closer, Ball bearing butt hinge of size 102*75*3mm with SS screw, Mortise dead bolt lock with euro profile, door stopper, door closer, Fire rated clear glass 200*300*6mm, D handle both side 19*254 mm, double shutter, with 300 mm ventilator, including installation etc. complete in all aspects as per direction of Engineer in Charge. (Make- Tata Pravesh) D1 opening size 1500*2400

Supply and installation ,Testing and Commissioning of FIRE RATED DOOR tested for 2 hours all included frame thicknes 100*58 mm, frame sheet thickness 1.2 mm with Rockwool infill, Door leaves sheet thickness 0.8mm skin pass galvanised iron sheet with honeycomb Kraft paper infill, leaf thickness 46mm, door stopper, door closer, Ball bearing butt hinge of size 102*75*3mm with SS screw, Mortise dead bolt lock with euro profile, door stopper, door closer, Fire rated clear glass 200*300*6mm, D handle both side 19*254 mm, double shutter, with 300 mm ventilator, including installation etc. complete in all aspects as per direction of Engineer in Charge. (Make- Tata Pravesh) D2 opening size 2540*2400 double leaf

Supply and installation ,Testing and Commissioning of FIRE RATED DOOR tested for 2 hours all included frame thicknes 100*58 mm, frame sheet thickness 1.2 mm with Rockwool infill, Door leaves sheet thickness 0.8mm skin pass galvanised iron sheet with honeycomb Kraft paper infill, leaf thickness 46mm, door stopper, door closer, Ball bearing butt hinge of size 102*75*3mm with SS screw, Mortise dead bolt lock with euro profile, door stopper, door closer, Fire rated clear glass 200*300*6mm, D handle both side 19*254 mm, double shutter, with 300 mm ventilator, including installation etc. complete in all aspects as per direction of Engineer in Charge. (Make- Tata Pravesh) D3 opening size 1200*2400 single leaf

Providing and fixing G.I.swing Door Supply and installation ,Testing and Commissioning of FIRE RATED DOOR tested for 2 hours all included frame thicknes 100*58 mm, frame sheet thickness 1.2 mm with Rockwool infill, Door leaves sheet thickness 0.8mm skin pass galvanised iron sheet with honeycomb Kraft paper infill, leaf thickness 46mm, door stopper, door closer, Ball bearing butt hinge of size 102*75*3mm with SS screw, Mortise dead bolt lock with euro profile, door stopper, door closer, Fire rated clear glass 200*300*6mm, D handle both side 19*254 mm, double shutter, with 300 mm ventilator, including installation etc. complete in all aspects as per direction of Engineer in Charge. (Make- Tata Pravesh) D10 opening size 1500*2400 Emergency door with panic bar D8 opening size 900*2400 single leaf Emergency Door with panic bar

Supply and installation ,Testing and Commissioning of FIRE RATED DOOR tested for 2 hours all included frame thicknes 100*58 mm, frame sheet thickness 1.2 mm with Rockwool infill, Door leaves sheet thickness 0.8mm skin pass galvanised iron sheet with honeycomb Kraft paper infill, leaf thickness 46mm, door stopper, door closer, Ball bearing butt hinge of size 102*75*3mm with SS screw, Mortise dead bolt lock with euro profile, door stopper, door closer, Fire rated clear glass 200*300*6mm, D handle both side 19*254 mm, double shutter, with 300 mm ventilator, including installation etc. complete in all aspects as per direction of Engineer in Charge. (Make- Tata Pravesh) D7 opening size 750*2100 single leaf

Supply and installation ,Testing and Commissioning of FIRE RATED DOOR tested for 2 hours all included frame thicknes 100*58 mm, frame sheet thickness 1.2 mm with Rockwool infill, Door leaves sheet thickness 0.8mm skin pass galvanised iron sheet with honeycomb Kraft paper infill, leaf thickness 46mm, door stopper, door closer, Ball bearing butt hinge of size 102*75*3mm with SS screw, Mortise dead bolt lock with euro profile, door stopper, door closer, Fire rated clear glass 200*300*6mm, D handle both side 19*254 mm, double shutter, with 300 mm ventilator, including installation etc. complete in all aspects as per direction of Engineer in Charge. (Make- Tata Pravesh) D4 opening size 900*2400 single leaf

Supply and installation ,Testing and Commissioning of FIRE RATED DOOR tested for 2 hours all included frame thicknes 100*58 mm, frame sheet thickness 1.2 mm with Rockwool infill, Door leaves sheet thickness 0.8mm skin pass galvanised iron sheet with honeycomb Kraft paper infill, leaf thickness 46mm, door stopper, door closer, Ball bearing butt hinge of size 102*75*3mm with SS screw, Mortise dead bolt lock with euro profile, door stopper, door closer, Fire rated clear glass 200*300*6mm, D handle both side 19*254 mm, double shutter, with 300 mm ventilator, including installation etc. complete in all aspects as per direction of Engineer in Charge. (Make- Tata Pravesh) D6 opening size 900*2100 single leaf

Supply and installation ,Testing and Commissioning of FIRE RATED DOOR tested for 2 hours all included frame thicknes 100*58 mm, frame sheet thickness 1.2 mm with Rockwool infill, Door leaves sheet thickness 0.8mm skin pass galvanised iron sheet with honeycomb Kraft paper infill, leaf thickness 46mm, door stopper, door closer, Ball bearing butt hinge of size 102*75*3mm with SS screw, Mortise dead bolt lock with euro profile, door stopper, door closer, Fire rated clear glass 200*300*6mm, D handle both side 19*254 mm, double shutter, with 300 mm ventilator, including installation etc. complete in all aspects as per direction of Engineer in Charge. (Make- Tata Pravesh)D5 opening size 1200*2400 single leaf Emergency door with panic bar

Supply and installation ,Testing and Commissioning of FIRE RATED DOOR tested for 2 hours all included frame thicknes 100*58 mm, frame sheet thickness 1.2 mm with Rockwool infill, Door leaves sheet thickness 0.8mm skin pass galvanised iron sheet with honeycomb Kraft paper infill, leaf thickness 46mm, door stopper, door closer, Ball bearing butt hinge of size 102*75*3mm with SS screw, Mortise dead bolt lock with euro profile, door stopper, door closer, Fire rated clear glass 200*300*6mm, D handle both side 19*254 mm, double shutter, with 300 mm ventilator, including installation etc. complete in all aspects as per direction of Engineer in Charge. (Make- Tata Pravesh) D9 opening size 1500*2400 OT doors, hermetically treated

Supply and installation ,Testing and Commissioning of Factory made uPVC white color window/ventilator comprising of uPVC multi-chambered frame and million (where ever required) extruded profiles duly reinforced with 1.60 + 0.2 mm thick galvanized mild steel section of required length, toughened glass 6mm thick (shape and size according to uPVC profile) uPVC extruded glazing beads of appropriate dimension, frame & mullion of 45mm, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. including drilling of holes for fixing hardware's and drainage of water etc. weather proof silicon sealant of approved quality, all complete as per approved drawing & direction of Engineer-in Charge.(Make- FENNESTA) V1 opening size 1800*600, top hung and ventilator

Supply and installation ,Testing and Commissioning of Factory made uPVC white color window/ventilator comprising of uPVC multi-chambered frame and million (where ever required) extruded profiles duly reinforced with 1.60 + 0.2 mm thick galvanized mild steel section of required length, toughened glass 6mm thick (shape and size according to uPVC profile) uPVC extruded glazing beads of appropriate dimension, frame & mullion of 45mm, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. including drilling of holes for fixing hardware's and drainage of water etc. weather proof silicon sealant of approved quality, all complete as per approved drawing & direction of Engineer-in Charge.(Make- FENNESTA) V3 opening size 1200*600, top hung and ventilator

Supply and installation ,Testing and Commissioning of Factory made uPVC white color window/ventilator comprising of uPVC multi-chambered frame and million (where ever required) extruded profiles duly reinforced with 1.60 + 0.2 mm thick galvanized mild steel section of required length, toughened glass 6mm thick (shape and size according to uPVC profile) uPVC extruded glazing beads of appropriate dimension, frame & mullion of 65mm, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. including drilling of holes for fixing hardware's and drainage of water etc. weather proof silicon sealant of approved quality, all complete as per approved drawing & direction of Engineer-in Charge.(Make- FENNESTA) W3 opening size 1200*1500, 3 track slider with SS wire bugscreeen

Supply and installation ,Testing and Commissioning of Factory made uPVC white color window/ventilator comprising of uPVC multi-chambered frame and million (where ever required) extruded profiles duly reinforced with 1.60 + 0.2 mm thick galvanized mild steel section of required length, toughened glass 6mm thick (shape and size according to uPVC profile) uPVC extruded glazing beads of appropriate dimension, frame & mullion of 45mm, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. including drilling of holes for fixing hardware's and drainage of water etc. weather proof silicon sealant of approved quality, all complete as per approved drawing & direction of Engineer-in Charge.(Make- FENNESTA) V7 opening size 2400*600, top hung and ventilator

Supply and installation ,Testing and Commissioning of Factory made uPVC white color window/ventilator comprising of uPVC multi-chambered frame and million (where ever required) extruded profiles duly reinforced with 1.60 + 0.2 mm thick galvanized mild steel section of required length, toughened glass 6mm thick (shape and size according to uPVC profile) uPVC extruded glazing beads of appropriate dimension, frame & mullion of 45mm, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. including drilling of holes for fixing hardware's and drainage of water etc. weather proof silicon sealant of approved quality, all complete as per approved drawing & direction of Engineer-in Charge.(Make- FENNESTA) V5 opening size 600*600, top hung

Supply and installation ,Testing and Commissioning of Factory made uPVC white color window/ventilator comprising of uPVC multi-chambered frame and million (where ever required) extruded profiles duly reinforced with 1.60 + 0.2 mm thick galvanized mild steel section of required length, toughened glass 6mm thick (shape and size according to uPVC profile) uPVC extruded glazing beads of appropriate dimension, frame & mullion of 45mm, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. including drilling of holes for fixing hardware's and drainage of water etc. weather proof silicon sealant of approved quality, all complete as per approved drawing & direction of Engineer-in Charge.(Make- FENNESTA) V4 opening size 900*600, top hung and ventilator

Supply and installation ,Testing and Commissioning of Factory made uPVC white color window/ventilator comprising of uPVC multi-chambered frame and million (where ever required) extruded profiles duly reinforced with 1.60 + 0.2 mm thick galvanized mild steel section of required length, toughened glass 6mm thick(shape and size according to uPVC profile) uPVC extruded glazing beads of appropriate dimension, frame & mullion of 65mm, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. including drilling of holes for fixing hardware's and drainage of water etc. weather proof silicon sealant of approved quality, all complete as per approved drawing & direction of Engineer-in Charge.(Make- FENNESTA) W5 opening size 900*1500, 3 track slider with SS wire bugscreeen

Supply and installation ,Testing and Commissioning of Factory made uPVC white color window/ventilator comprising of uPVC multi-chambered frame and million (where ever required) extruded profiles duly reinforced with 1.60 + 0.2 mm thick galvanized mild steel section of required length, toughened glass 6mm thick (shape and size according to uPVC profile) uPVC extruded glazing beads of appropriate dimension, frame & mullion of 45mm, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. including drilling of holes for fixing hardware's and drainage of water etc. weather proof silicon sealant of approved quality, all complete as per approved drawing & direction of Engineer-in Charge.(Make- FENNESTA) W1 opening size 1200*1500, 3 track slider with SS wire bugscreeen

Supply and installation ,Testing and Commissioning of Factory made uPVC white color window/ventilator comprising of uPVC multi-chambered frame and million (where ever required) extruded profiles duly reinforced with 1.60 + 0.2 mm thick galvanized mild steel section of required length, toughened glass 6mm thick(shape and size according to uPVC profile) uPVC extruded glazing beads of appropriate dimension, frame & mullion of 45mm, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. including drilling of holes for fixing hardware's and drainage of water etc. weather proof silicon sealant of approved quality, all complete as per approved drawing & direction of Engineer-in Charge.(Make- FENNESTA) W2 opening size 2400*1500, 3 track slider with SS wire bugscreeen

Supply and installation ,Testing and Commissioning of Factory made uPVC white color window/ventilator comprising of uPVC multi-chambered frame and million (where ever required) extruded profiles duly reinforced with 1.60 + 0.2 mm thick galvanized mild steel section of required length, toughened glass 6mm thick (shape and size according to uPVC profile) uPVC extruded glazing beads of appropriate dimension, frame & mullion of 45mm, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. including drilling of holes for fixing hardware's and drainage of water etc. weather proof silicon sealant of approved quality, all complete as per approved drawing & direction of Engineer-in Charge.(Make- FENNESTA) V6 opening size 300*600,top hung

Aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make, including tubular handle bar of 32 mm/ round shape handle of outer dia 100mm, hanging door stopper, hydraulic door closer, 12 mm thick prelaminated particle board conforming to IS:12826 grade,12mm thick toughened glass door shutter conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps atjunctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, including hinges, pivots all complete as per architectural drawings and the directions of Engineer-in-charge : Powder coated aluminium (minimum thickness of powder coating 50 micron)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.: Hot finished welded type tubes

Anti Skid Epoxy Flooring for Car Parking : Available in many formulation options, Tile grout meeting defined industry standards, Allows for easy installation support, Support maintaining the beautiful and durable finish, Suitable to be used for both homeowners and professionals, Made available at competitive prices

Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge. In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) Acid and alkali resistant tile

Providing and laying vitrified double charge floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 12x18 Inch or 12x24 Inch or as per direction of Engineer-in-charge

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. completeGranite of any colour and shade

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).: Dark shade pigment using ordinary cement

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate

Providing and fixing Ist quality Anti Skid floor tiles as Per Following Approved Specification, water absorbtion of <0.5%, breaking strenght of >1800 N, Deep abrasion resistance of <1200 mm, censity of >2.2gm/cc,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade. 8mm thick (mirror polished and machine cut edge) Granite stone of any colour and shade

Providing and fixing Ist quality Thermatek Heat Resistant Tiles as Per Following Approved Specification, Supply of 300x300 mm Roof Tiles, Appearance White (Stone Punch Finish), Solar Reflective Index (SRI) 102 (ASTM E 1980)Reflctance 0.8121, Emissivity 0.8921, Materials used-Infrared Resistive Composition (NON Degradable), Tile Thickness - 10MM (±), Imprevious to Water, Stain Resistant, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm with spacers and appoxy grout.

ESD Flooring Tiles : PVC Conductive Agent and Metal Particles pressed with PVC 610x610 mm (LxW)

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

15 mm thick cement plaster in cement mortar 1:6 on Rough Side of brick wall including supply of all material , labour and T&P etc.

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Stone work (machine cut edges Veneer work) for wall lining upto 10 m height, backing filled with a grout of 12 mm thick cement mortar 1:3 (1 Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement : 2 stone dust), including rubbing and polishing complete. (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately). Kota stone slabs exposed face dressed and rubbed. 25 mm thick

Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc. ,all complete for the required performances as specified, as per the Architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in charge.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels/ subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guaranteed for 10 years against any leakage. For vertical surface two coats @0.70 kg per sqm per coat

Renovating lawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure, mixing the same with forked soil, watering and maintaining the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good earth if needed but excluding the cost of sludge or manure(the good earth shall be paid for separately)

Construction of Embankment with Material Obtained from Roadway Cutting Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Plastering with cement mortar (1:4), 15 mm thick on brickwork in substructure as per technical specification Clauses 613.4 & 1204

Excavation for Structures Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. Ordinary soil Upto 3 m depth

Trenching in ordinary soil up to a depth of 60cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling with in a lead of 50m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking sludge at site including royalty and carriage up to 1 km(sludge measured in stacks will be reduced by 8% for payment)

Supplying and stacking at site dump manure from approved source, including carriage up to 1 km (manure measured in stacks will be reduced by 8% for payment) screened through sieve of I.S. designation 4.75 mm

Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge.

Suply and plantation of mature trees including excavation of pit, providing manure and watering and caring for one year as per directions of Engineer-Incharge

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : 25 mm dia

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing roofing consist of 0.8 mm thick galvanized steel deck sheet confirming to IS 277:1992 used as permanent shuttering over which MS wire mesh 3mm laid at 100x100 mm grid including edge trim covered with concrete. This metal deck will be supported on structural steel beam with shear studs. (Structural steel like Beam, column, joists etc. & concrete of different grade as per design will be paid separately).

WBM Grading 1 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 1 as per Technical Specification Clause 404. By Manual Means

Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.

Providing, fabricating and supplying shadow box of required size and shape, for fixing in the spandrel portion of the structural glazing, in linear as well as curvilinear portions of the building by providing semi -rigid, inorganic, non-combustible fibre glass wool insulation 50 mm thick, conforming to IS: 8183 and BS: 3958 Part 5. The insulation layer shall have facing (factory bonded on surface # 1 of the fibre glass insulation layer), of black non-woven fibre glass tissue of nominal thickness 0.5 mm and nominal mass not less than 60 gm /sqm, made of randomly oriented glass fibres distributed in a binder by a wet-lay process including fixing 1.5 mm thick solid aluminum sheet backing using, 6 mm thick cement board including SS rivets, nuts, bolts, washers etc complete.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for allheights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles,nuts, bolts, clamps etc., structural and weather silicone sealants,EPDM gaskets for water tightness, pressure equalisation &drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge.

Extra for openable side / top hung vision glass panels (IGUs) including openable panels as specified and of the approved make such as providing and supplying at site all accessories and hardwares for the heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

Providing, assembling and supplying vision glass panels (IGUs)comprising of hermetically-sealed 6-12- 6 mm insulated glass (double comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge.

Supply fixing & testing for Mechanical fasteners hilti 16 mm thickness.

Brick masonry work in cement mortar in substructure complete excepting pointing and plastering, as per drawing and technical specification Clauses 602, 603, 604, 1202 & 1204 In 1:4 Cement mortar

R.C.C grade M 20 as per design mix excluding the cost of centering, shuttering and reinforcement-All work upto plinth level

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 20 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 32 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 40 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 50 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 80 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.. External work80 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 15 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 20 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 25 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 32 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 40 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 50 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 80 mm dia nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 50 mm nominal bore. Horizontal

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 80 mm nominal bore. Horizontal

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge : 15 mm nominal dia (Jaquar)

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore (Jaquar)

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approvedquality . (Jaquar) (15 mm nominal bore)

Providing and fixing C.P. brass angle cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore (Jaquar)

Supply and installation of Kirloskar make pump Type KDS 527++ (2HP) Three phase Suc X Del 80 X 65, Head 30 mtr Flow 18.3 Lps, MOC Impeller CI,Pump Casing CI complete in all aspects as per direction of Engineer In-charge

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm or As per direction of Engineer - In - Charge with integral type foot rests (Make- Parryware, CERA, Hindware)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid (Make- Parryware, CERA, Hindware)

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern (Make- Parryware, CERA, Jaguar)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar tap (Make- Parryware, CERA, Jaguar)

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 1500x450 mm

Providing and fixing C.P Brass towel ring (Cera F5002105)

Providing and fixing Soap Dish (Cera F5003106)

Providing and fixing Liquid soap Dispenser (Cera F5007111)

Providing and fixing soil, waste and vent pipes IS 13592 & fitting (IS:14735) suitable to rubber ring joints, which includes bends, rubber ring, jointing, junctions, clean out plug, cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design, etc. complete including jointing. 110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

Providing and fixing soil, waste and vent pipes IS 13592 & fitting (IS:14735) suitable to rubber ring joints, which includes bends, rubber ring, jointing, junctions, clean out plug, cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design, etc. complete including jointing. 75 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type - B

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee with door 75x75x75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110x110x110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee without door 75x75x75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee without door 110x110x110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 75 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 110 mm bend each

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110 mm

Providing and fixing soil , waste and vent pipes: Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 100 mm dia

Providing and fixing soil , waste and vent pipes: Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 75 mm dia

Providing and fixing single unequal plain junction of required degree : Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 100x100x75 mm

Providing and fixing double equal plain invert branch of required degree: Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 100x100x100x100 mm

Providing and fixing single equal plain invert branch of required degree : Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 100x100x100 mm

Providing and fixing single equal plain invert branch of required degree : Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 75x75x75 mm

Providing and fixing single unequal plain invert branch of required degree : Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 100x100x75 mm

Providing and fixing Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905 65 mm offsets With 100 mm dia pipe

Providing and fixing Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905 65 mm offsets With 75 mm dia pipe

Providing and fixing Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905 130 mm offsets With 100 mm dia

Providing and fixing Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905 130 mm off sets With 75 mm dia

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 3989

Providing and fixing C.P. brass bottle trap for wash basin including CP waste fittings complete 32 mm dia complete in all respect of approved quality.(Jaquar)

Providing and fixing terminal guard 100 mm Sand cast iron S&S as per IS - 1729

Providing and fixing collar : 100mm

Providing and fixing collar : 75 mm

Providing and fixing Gyeser (Water Storage Heater) 25 Litres Capacity make Jaquar /Havells

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 450 mm dia RCC pipes.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded 300 mm diameter S. W. pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x90 cm and 45 cm deep with precast RCC cover with frame with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth beyond 45cm for manholes Size 90x90x45 cm With F.P.S brick class designation 75

SITC OF WATER SOFTNER & AUTOMATION.

NGS – 20B ( Softener)

NGMF85 (Sand Filter)

NGMA110 (CARBON FILTER)

Providing , fixing, installation and testing of horizontal multistage centrifugal pumping set with CED Coated CI connections, SS-304 impeller, SS-316 shaft and IE-2 Class induction motor mounted on common base frame, vibration eliminating pads accessories, including suction and delivery headers with G.I "C" class pipe with CED Coating of required dia, isolation valves, Butterfly valves, Y strainer, NRV & vibration eliminators on both suction & delivery side of pumps, and complete as per specifications. Motor to be suitable for 415 Volts + 10%, 3 phase 50 Hz. A/C supply with Control Panel with Require motor Protection etc as required as complete Domestic Water Transfer Pump (1W +1S) Location - Plant Room, Capacity - 150 LPM, Head - 40 M.- 2 sets Grundfos Make - Hydro Multi S 2 X CM 10-03 Complete Factory Fitted System

Providing, fixing, installation (Up to header) & Commissioning of Submersible drainage Pumps vertical stage S.S. pump with float type controller automatic operation required flow rate per hour, required head, submersible type, suitable for clear water drainage & 30 mm solid handling capacity complete with motor, control panel, submersible cable, built in suction strainer, bottom support frame and dual plate type NRV’s including headers with G.I "C" class pipe of required dia, isolation valves, NRV & vibration eliminators of pumps, other accessories as required. - Location - Pump Room (1w+1SB)=1set Capacity - 210 LPM. Head - 15 M. Efficiency - Class 2 Standard with digital control panel as required.

Providing, fixing, installation (Up to header) & Commissioning of Submersible drainage Pumps vertical stage S.S. pump with float type controller automatic operation required flow rate per hour, required head, submersible type, suitable for clear water drainage & 30 mm solid handling capacity complete with motor, control panel, submersible cable, built in suction strainer, bottom support frame and dual plate type NRV’s including headers with G.I "C" class pipe of required dia, isolation valves, NRV & vibration eliminators of pumps, other accessories as required. - Location - Basement (1w+1SB)=1set Capacity - 750 LPM. Head - 15 M. Efficiency - Class 2 Standard Grundfos Make- DPK.15.80.37.5.0D with Control Panel

Supply, installation, testing and commissioning of following Automation and instrumentation including all sensors, relays, level controller/switches, level indicators etc. Relays/Modules and wiring for completely functional system. To cut off duty pump on low water level in the sump, To start pump at high water level in the sump and both pumps start when water over flowing. for Automatic switching ON-OFF of following pumps: Raw water pumps from Level Controller (four level float type) installed in Filter Water Tank. - 4 nos Make- Punetechtrol/Aster

Tube well pumps from Level Controller (four level float type) installed in Raw Water Tank including Dry Run Preventer for each of the above pumps by providing Low level sensor in the three tank viz Raw Water tank, Filter water tank and Soft water tank. -2 nos Make- Punetechtrol/Aster For Basement Drainage Sump Pumps. -2 nos Make- Punetechtrol/Aster

Providing and fixing standard dial type pressure gauge dia 100 mm with screwed inlet with isolation cock suitable for liquid gauge to show pressure upto: i ) (0-5) KG/Sq.cm

Providing and fixing standard dial type pressure gauge dia 100 mm with screwed inlet with isolation cock suitable for liquid gauge to show pressure upto: ii ) (0-10) Kg/Sq.cm Make-Hguru

Filter Feed Pumps- Providing , fixing, installation and testing of horizontal multistage centrifugal pumping set with CED Coated CI connections, SS-304 impeller, SS-316 shaft and IE-2 Class induction motor mounted on common base frame, vibration eliminating pads accessories, including suction and delivery headers with G.I "C" class pipe with CED Coating of required dia, isolation valves, Butterfly valves, Y strainer, NRV & vibration eliminators on both suction & delivery side of pumps, and complete as per specifications. Motor to be suitable for 415 Volts + 10%, 3 phase 50 Hz. A/C supply with Control Panel with Require motor Protection etc as required as complete Domestic Water Transfer Pump (1W +1S) Location - Plant Room, Capacity - 142 LPM, Head - 25 M.- 2 sets Grundfos Make:- CM 10-2 1 Set ( 1 W + 1 S)

RAIN WATER HARVESTING

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collectingsamples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. All types of soil 400 mm dia All types of soil 400 mm dia

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collectingsamples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. All types of soil 400 mm dia Rocky strata including Boulders 400 mm dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed/plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm dia

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 110 mm Shoe (Plain) 110 mm Shoe

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe

Constructing brick masonry road gully chamber 45x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including pre-cast R.C.C. cover with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 60x60x45 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C. cover with frame and vertical grating complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth beyond 45 cm of brick masonry chamber : For 60x60 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

SEWEGE TREATMENT PLANT

Design, Drawing, Supplying , Installation, testing & commissioning of Packaged type Sewage Treatment Plant of 50 KLD on FMR ( Fluidised Media Reactor)/FAB (Fluidised Aerobic Bio Reactor) technology with Lamella/Tube Settler and providing all equipment, plant shall be design to run automatically according to dissolved oxygen (DO) level in the STP reactor and air blowers shall be operating according to the requirement of DO through VFD and the required equipments to achieve this shall be the part of scheme, piping etc at site including erection testing and commissioning of equipments, electricals, piping for Sewage Treatment Plant followed by MultiGrade Filter, Activated Carbon & Ultra Filtration Membrane System(Water After UF Membrane can be used for flushing, cooling tower, vehicle washing etc. including suitable size of puddle flanges, cascades etc as reqd. DESIGNED PARAMETERS OF THE STP Daily average flow - 50 KLD PH - 6.5-8.5 BOD 5 - 250-300 S. Solids - 200 - 350 COD - 600 - 800 Oil & Grease - 50 - 100 mg/lit Effluent discharge standard after treatment :- PH - 6.0 - 8.5 BOD 5 - less than 3 mg / liter S. Solids - less than 2 mg / liter COD - less than 10 mg / liter Oil & Grease - Nil Designed by M/s- Ion Exchange(I) Ltd. Exclusion- structure/Vetting. With following item.

Detailed, Design, GA drawing (plan, sectional, architectural ) flow diagram, equipment list, power load requirement, design calculation, civil supervision etc. 1 Job

Supplying, installing, testing & commissioning of Perforated SS-304 bar screen chamber 2nos. having perforation of 20 & 10mm respectively provision for lifting arrangement etc. complete as required. Size : 1000mm X 500mm Make- Ion Exchange

SITC of Water electronic level controller suitable for multilevel censors including wiring etc for operation of the system connected to control panel for automatic switching ON / OFF of each pump. 1 set Make- Pune techtrol/Aster

Supply, installation, testing & commissioning of non clogging monoblock type Sludge Recirculation Pump having CI casing & CI impeller complete with and foundation bolts all accessories, motor of required capacity. pressure gauge on delivery line with isolation cock, level controller to control the level of sump automatically of following capacity:-Flow Rate : 3.0 M3/Hr, Head : 10mtrSolid handling : 8mm (2Nos-1w+1s)Qty- 1 set Make-Kirloskar

SITC of 2 Nos. twin lobe type Rotary air blowers (1W + 1S) capable of delivering 75m3/hr of free air at 0.5 kg/cm2 driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles A/C supply. Including foundation and foundation bolts work. system should be supplied with sound level less than 85 db etc as reqd. 1 set Make- Everest

SITC of Settling Media: Lamella Settler/Tube duck ,media of required capacity as per 100 KLD. 1 Lot Make- Ion Exchange

SITC of MS Plates with FRP Lining Media retention plates to be fixed on over flow point of each reactor to stop free flowing of MBBR media into another reactor. 1 Lot Make- Ion Exchange

Providing and fixing all piping (as described below) and isolation control valves for making the system complete. Heavy Duty PVC/UPVC : Submerged air piping MS Epoxy : Air piping & pumped effluent riser (non-submerged)---- 1 Lot Make-MS-Jindal/PVC-Supreme

SITC of MBBR(FMR/FAB) media of Virgin PP for MBBR reaction chambers of at least 500 m2/m3 surface area and required quantity for 100 KLD. As per OEM standard/design. 1 Lot Make- Ion Exchange

Supplying, installing (Upto header) testing & commissioning of Non Submersible type non clog water pumps with CI casing and CI Impeller along with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, strainer (with by-pass) at suction. Mechanical seal, suitable vibration elimination pads of approved design, for the pump. The pump shall be suitable for 415±10% volts 3 phase AC supply. Including foundation bolts(1 Working + 1 Standby) of 6 m3/Hr, Head 30 Meter : 1 Set Kirloskar Make- KDI 235

Multigrade Filter: supplying, installation , testing and commission of multigrade sand pressure filter made from MS sheet for filtration of treated sewage water. The filter shall be suitable for 6 m3/hr flow rate and designed to operate for 14 hours. The filter shall be designed for a specific velocity of 20 m3/hr/sq.m area shall not be less then 600 mm DIA with Minimum height of shell 1875 mm. thickness of the shell/Disc should not be less than 5 mm/8mm . The filtration unit shall comply with the following technical requirements: Back wash duration - once in 24 hours for 20 min: Butterfly valves - 1.5 -2 inch: Painting Internal - Two coats of bituminous paint : painting external - One coat of red oxide primer and above that finish paint : Filtering Media - Multi grade of Sand / Pebbles: Pressure drop across unit -1.0 kg/sq.cm(max) : 1 set Make- Ion Exchange,Model- MGF-600 HOS-1875

ACTIVATED CARBON FILTER (ACF): Supply , installation , testing and commissioning of activated carbon filter made from MS sheet for filtration and removal of colour in treated sewage water. The filter shall be for 6 m3/hr flow rate and designed to operate for 13 hours. thickness of the shell/Disc should not be less than 5 mm/8mm. The ACF shall be designed for a specific velocity of 15m3/hr/sq.m area and the approx. dia shall not be less than 800 mm DIA with 1875 height of shell . The filtration unit shall comply with the following technical requirement: Flow rate -6 cu.m /hr; Back wash duration - Once in 24 hours for 20 minutes ; Butterfly valves -1.5/2 Inch; Painting Internal - two coats of bituminous paint ; Painting external - once coat of red oxide primer and above that finish paint; Filtering Media - Activated carbon ; Pressure drop across unit -1.0kg/sq.cm (max) Make- Ion Exchange,Model- ACF-800 HOS-1875

Supplying, installing (Upto header) testing & commissioning of Non Submersible type non clog water pumps with CI casing and CI Impeller along with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, strainer (with by-pass) at suction. Mechanical seal, suitable vibration elimination pads of approved design, for the pump. The pump shall be suitable for 415±10% volts 3 phase AC supply. Including foundation bolts(1 Working + 1 Standby) of 10 m3/Hr, Head 40 Meter : Kirloskar Make- KDI 550

Supply, installation, testing & commissioning of chemical dosing system comprising of 100 ltrs HDPE/FRP tank with 0-6 lph at 25 meter head, electronic metering type pump and SS agitator complete with motor. - Make- Ion Exchange

Supply, installation, testing & commissioning of electro-magnetic type flow meter of Size 50mm at inlet and outlet of STP including necessary wiring from flow meter to the control panel etc as reqd. - Make-Adept

Supply, installation, testing and commissioning of Filter press with 12"X12" with 18 nos PP virgin plates with all fittings & accessories suitable for Manual operation. 1 set along with Filter Press Feed Pumps Screw type of 1cubic meter/hr at 40 meter head, CI body, SS screw etc. Complete with all fittings & accessories. Including foundation and foundation bolts.( 2Nos.- 1W+1S) Make- W2people

Supply, installation (upto header) testing & commissioning of non clogging cutter type Submersible submersible Sewage Pumps- Grinder Type having CI casing & CI impeller, cutting blade of Carbide tip complete, with foundation bolt and all accessories like anti vibration pad with motor of required capacity, in non-submersible pumps. lifting chain for header made from in MS pipes duly epoxy painted fitted with pressure gauge on delivery line with isolation cock, level controller to control the level for provision to control the level of sump automatically, and pumps shall also be controlled according to the flow in STP/Chlorine Contact Tank. Pumps shall have following capacity :2No.(1W+1S) Flow Rate : 4m3/Hr, Head : 10mtr, Solid handling : 40 MM Qty- 1 set Grundfos Make:- SEG 40.09.2.50 with Auto- coupling

Supplying, installing, testing & commissioning of non clog de-watering Submersible pump for Plant Room Sump with CI body, CI Impeller along with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, Mechanical seal. The pump shall be suitable for 415±10% volts 3 phase AC supply, fitted with level switches and suitable capacity starter panel etc. (1w+1s) of 8cubic meter/ hr at 12 meter head. - 1 set Gundfos Make- DPK.10.50.15.5.0D including installatin of pumps upto header with control panel

EFFLUENT TREATMENT PLANT

Design, Drawing, Supply, Fabrication, installation (upto header), testing and commissioning of effluent treatment plant with effluent handling capacity 10 m3 per day. The entire plant will be constructed in MS (FRP coated, min. 3 mm/anticorrosive paint). The ETP shall be designed as water retaining structures, with necessary chemical dosing as required by the manufacturer's design. All the equipment, piping, pumps, air blowers and electrical panel to be housed in the ETP skid including M.S. puddle flange (Galvanised), inlet, outlet, overflow, vent, moving ladders & railing. The Plant shall be complete with a central Electrical Power and Control panel fully pre/site wired and with all power and control cables to all pumps and equipment including all instrumentation, level and other controls. The cost will also include any consequential civil work including making foundations for the structure, pumps, blowers etc. It should be complete as per manufacturer's specifications & as directed by Engineer-in-charge. Effluent from OT Scrubs, blood bank, labs etc. Some solvent/ chemical waste originating typically from hospital complex shall also be discharged into the ETP. Design to take consideration of same. Daily average flow : 10 Cum/Day PH : 5.5 - 9.0 BOD : 250 - 600 mg/l S. Solids : 200 - 650 Mg/lCOD : 600 - 1200 mg/l Oil & Grease : 50-140 mg/L Effluent discharge standard after treatment :- PH : 7.0 - 8.5 S. Solids : Less than 400 mg/l COD : Less than 100 mg/l Oil & Grease : Less than 5 mg/l BOD : Less than 30 Mg/L SITC of effluent transfer pump (1w+1s) submersible type having SS-304 body and SS-304 impeller of 1cubic meter / hr and 10 meter head. - 1 set

SS Perforated screen having provision for lifting arrangement etc. complete as required. - 1 set Make-Ion Exchange

Reaction tank Min. 2 Cum with suitable capacity of air blower along with air diffuser and piping complete of adequate capacity. Fine air bubble jet diffuser with EPDM seat minimum number of diffusers to be provided as per manufacturer's recommendations in MS (FRP/ anti corrosive paint) Construction. provision of aeration into collection tank, sludge holding tank also be provided - 1set Make-Ion Exchange

Secondary clarifier tank Min. 3 Cum, hopper bottom type with arrangement of deep well, baffle wall, scum removal arrangement, outlet launders with arrangement of lifting sludge from the bottom etc. complete as required in MS (FRP/ anti corrosive paint) Construction. - 1 set Make-Ion Exchange

Providing and fixing all piping (as described below) and isolation control valves, non return valves etc. for making the system complete. PVC piping (10kg/sqcm) - For all submerged waste water piping. MS (C Class) - For all exposed air piping and flexible stainless steel pipe for submerged air piping. GI (C class) for all other water piping. Providing and fixing all instrumentation eg. Pressure gauges, level controllers, sensors, rota metres for air, water etc. for making the system complete. Qty- 1 Lot Make- MS/GI- Jindal PVC-Supreme/Astral

DIGESTED SLUDGE DISPOSAL PUMP : Providing, installation, testing & commissioning of Sludge disposal pump for the disposal of sludge to tanker or to sludge dry beds. The pumps shall have CI casing, bronze/ CI Impeller , 100 mm dia with pressure gauge with GM isolation cock, suitable vibration eliminator pads of approved design. Motor to be suitable for including all necessary piping, valves and other accessories and concrete foundation complete as required. (1 Working + 1 Stand-by) .of 2 cubic meter/hr at 20 meter head.- 1set Make- Kirloskar

Supply, installation, testing and commissioning of Basket type centrifuge with interconnecting piping and poly dosing system all complete of 400mm dia. - 1set

Providing ,fixing, testing and commissioning of lime/alum/polyelectrolyte dosing system consisting of ABS lime dosing pump (0-6 lph) with 100Ltr HDPE tanks including all piping from the dozer to the reaction tank etc. complete in all respects.- 3 Nos Make- Ion Exchange

Supply, installing, testing & commissioning of Electrical system including Electrical Panel for all the above including all switchgear, cables, control wiring, multi function millimetres etc., also including the complete automation of the plant with level controllers and sensors in the HDPE and the MS tanks, control cabling, complete in all respects as required as per IS specifications. - 1 set Make-Ion Exchange approved

All electrical and mechanical items as required to operate the system automatically and also include in his rates any other components/tanks/ equipment/ etc. required to complete the job as required. The electrical panel will also include all the required NO/NC contacts, contactors etc. required to provide BMS connectivity. Bypass arrangement shall be provided such that equalization tank pump can be used to pump out sewage to external manhole in case of maintenance of ETP.

MEDICAL GAS PIPE LINE

Supply,Installation testing and commissiong of Medical Grade Copper Pipe : The piped distribution system shall use copper pipes manufactured from phosphorous de-oxidised non-arsenical copper to BS EN 1412:1996 grade CW024A (Cu-DHP), manufactured to metric outside diameters and having mechanical properties in accordance with BS EN 13348:2008 in either R250 (half hard) or R290 (hard). Degreasing of pipe shall be such that there is less than 20mg/m2 (0.002mg/cm2) of hydrocarbons on the degreased surface when tested by the method specified BS EN 13348:2008. with Lloyd certified . 54mm OD X 1.2mm thick

Supply,Installation testing and commissiong of Medical Grade Copper Pipe : The piped distribution system shall use copper pipes manufactured from phosphorous de-oxidised non-arsenical copper to BS EN 1412:1996 grade CW024A (Cu-DHP), manufactured to metric outside diameters and having mechanical properties in accordance with BS EN 13348:2008 in either R250 (half hard) or R290 (hard). Degreasing of pipe shall be such that there is less than 20mg/m2 (0.002mg/cm2) of hydrocarbons on the degreased surface when tested by the method specified BS EN 13348:2008. with Lloyd certified . 42mm OD X 1.2mm thick

Supply,Installation testing and commissiong of Medical Grade Copper Pipe : The piped distribution system shall use copper pipes manufactured from phosphorous de-oxidised non-arsenical copper to BS EN 1412:1996 grade CW024A (Cu-DHP), manufactured to metric outside diameters and having mechanical properties in accordance with BS EN 13348:2008 in either R250 (half hard) or R290 (hard). Degreasing of pipe shall be such that there is less than 20mg/m2 (0.002mg/cm2) of hydrocarbons on the degreased surface when tested by the method specified BS EN 13348:2008. with Lloyd certified . 28mm OD X 0.9mm thick

Supply,Installation testing and commissiong of Medical Grade Copper Pipe : The piped distribution system shall use copper pipes manufactured from phosphorous de-oxidised non-arsenical copper to BS EN 1412:1996 grade CW024A (Cu-DHP), manufactured to metric outside diameters and having mechanical properties in accordance with BS EN 13348:2008 in either R250 (half hard) or R290 (hard). Degreasing of pipe shall be such that there is less than 20mg/m2 (0.002mg/cm2) of hydrocarbons on the degreased surface when tested by the method specified BS EN 13348:2008. with Lloyd certified . 22mm OD X 0.9mm thick

Supply,Installation testing and commissiong of Medical Grade Copper Pipe : The piped distribution system shall use copper pipes manufactured from phosphorous de-oxidised non-arsenical copper to BS EN 1412:1996 grade CW024A (Cu-DHP), manufactured to metric outside diameters and having mechanical properties in accordance with BS EN 13348:2008 in either R250 (half hard) or R290 (hard). Degreasing of pipe shall be such that there is less than 20mg/m2 (0.002mg/cm2) of hydrocarbons on the degreased surface when tested by the method specified BS EN 13348:2008. with Lloyd certified . 15mm OD X 0.7mm thick

Supply,Installation testing and commissiong of Medical Grade Copper Pipe : The piped distribution system shall use copper pipes manufactured from phosphorous de-oxidised non-arsenical copper to BS EN 1412:1996 grade CW024A (Cu-DHP), manufactured to metric outside diameters and having mechanical properties in accordance with BS EN 13348:2008 in either R250 (half hard) or R290 (hard). Degreasing of pipe shall be such that there is less than 20mg/m2 (0.002mg/cm2) of hydrocarbons on the degreased surface when tested by the method specified BS EN 13348:2008. with Lloyd certified . 12mm OD X 0.6mm thick

Gas Outlet Points/ Terminal Unit for Installation, testing and commissioning of Gas outlet points for Oxygen, Nitrous Oxide, Medical Air 4 Bar It should comply and fully meets with the latest standard HTM02-01 and C11. It should be CE marked . Oxygen

Gas Outlet Points/ Terminal Unit for Installation, testing and commissioning of Gas outlet points for Oxygen, Nitrous Oxide, Medical Air 4 Bar It should comply and fully meets with the latest standard HTM02-01 and C11. It should be CE marked . Nitrous Oxide

Gas Outlet Points/ Terminal Unit for Installation, testing and commissioning of Gas outlet points for Oxygen, Nitrous Oxide, Medical Air 4 Bar It should comply and fully meets with the latest standard HTM02-01 and C11. It should be CE marked . Medical Air 4 Bar

Gas Outlet Points/ Terminal Unit for Installation, testing and commissioning of Gas outlet points for Oxygen, Nitrous Oxide, Medical Air 4 Bar It should comply and fully meets with the latest standard HTM02-01 and C11. It should be CE marked . Vacuum

Installation, testing and commissioning of Matching Probe/adopter with one end suitable for Hose & other end suitable for terminal units/ Gas Outlet Point. Oxygen

Installation, testing and commissioning of Matching Probe/adopter with one end suitable for Hose & other end suitable for terminal units/ Gas Outlet Point. Nitrous Oxide

Installation, testing and commissioning of Matching Probe/adopter with one end suitable for Hose & other end suitable for terminal units/ Gas Outlet Point. Medical Air 4 Bar

Installation, testing and commissioning of Matching Probe/adopter with one end suitable for Hose & other end suitable for terminal units/ Gas Outlet Point. Vacuum

Area Valve Box : Supply, Installation, testing and commissioning of Indigenous Area Valve box along isolation valve with stub pipes and pressue gauge. As per tender technical specifications and approved makes. AVB- 2 Services

Area Valve Box : Supply, Installation, testing and commissioning of Indigenous Area Valve box along isolation valve with stub pipes and pressue gauge. As per tender technical specifications and approved makes. AVB- 3 Services

Area Valve Box : Supply, Installation, testing and commissioning of Indigenous Area Valve box along isolation valve with stub pipes and pressue gauge. As per tender technical specifications and approved makes. AVB- 4 Services

Medical Gas Alarm Panel : Supply, Installation, testing and commissioning of IndigenousMicroprocessor controlled Digital Medical Gas Alarm Panel . As per tender technical specifications and approved makes. Master Alarm panel 4 services (Oxygen, N2O, MA4 Air, SA7 Air, and Vacuum)

Medical Gas Alarm Panel : Supply, Installation, testing and commissioning of IndigenousMicroprocessor controlled Digital Medical Gas Alarm Panel . As per tender technical specifications and approved makes. Medical Gas Area Alarm for 2 services (Oxygen and Vacuum)

Medical Gas Alarm Panel : Supply, Installation, testing and commissioning of IndigenousMicroprocessor controlled Digital Medical Gas Alarm Panel . As per tender technical specifications and approved makes. Medical Gas Area Alarm for 3 services (Oxygen, MA4 Air and Vacuum)

Medical Gas Alarm Panel : Supply, Installation, testing and commissioning of IndigenousMicroprocessor controlled Digital Medical Gas Alarm Panel . As per tender technical specifications and approved makes. Medical Gas Area Alarm for 4 services (Oxygen, N2O, MA4 Air, and Vacuum)

Fully Automatic Oxygen Control System : Supply, Installation testing and commissioning of Indigenous 1000lpm Fully Automatic Oxygen Control System.

Oxygen Manifold (2x10) : Supply, Installation, Testing and Commissioning of Indigenous Oxygen Manifold (10+10). The cylinders shall not be included in the quoted price.

Emergency Oxygen Supply System : Supply, Installation, testing and commissioning of (2x5size) cylinder Emergency Oxygen Supply System. The cylinders shall not be included in the quoted price.

Indigenous Oxygen Flow meter with Humidifier Bottle - Supply installation, testing and commissioning of Indigenous oxygen flow meter with humidifier bottle 0-15Litres.

Indigenous Semi Automatic Manifold Control Panel for Nitroux Oxide: Supply installation testing and commission of indigenous 500lpm Fully automatic manifold control panel for Nitrous Oxide•

Indigenous Nitrous Oxide Manifold (2x2): Supply installation testing and commissioning of nitrous Oxide Manifold (2+2). The cylinder shall not be included on the quoted price.•

Indigenous Emergency Nitrous Oxide Supply System 1+1 size : Supply installation, testing and commissioning of 1+1 cylinder Emergency Nitrous Oxide supply System. The cylinder shall not be included in the quoted price.

Medical Vacuum Plant : Suply installation testing and commissiong of Medical Vacuum Plant consist with 2nos. Vacumm pumps having nominal pumping speed (50Hz / 60Hz) 300/360 m3/h, Ultimate pressure (without gas ballast valve)-0.1 ... 0.5 ► see nameplate (NP) hpa (mbar), Ultimate pressure (with gas ballast valve)-0.5 ... 1.0 hpa (mbar), Nominal motor rating (50Hz / 60Hz)-8.3 / 3x15 KW, Water vapour capacity (withgas ballast valve) -5/5.8 kg/h, Max. allowable pressure in the oil mist separator-1600hpa, Max. allowable gas inlet temperature °C - ≤50 hPa (mbar) ► 150, Ambient temperature range 29° C and 2000 ltr vacuum tank with NRV and Isolation Valave

Suply installation testing and commissiong of Medical Air Plant 15 HP with 1000 Ltr. Receiver tank and Heatless air dryer 65CFM , 3stage filtration system (Compressor Unit)

Indigenous Vacuum Unit : Suply installation testing and commissiong of Suction unit which consists of the following :- 1no. Suction Regulator and 1no. 600ml polysulphone collection jar. Suction Regulator :

Indigenous Theatre Suction Unit : Supply installation, testing and commissioning of Theatre Suction Unit.It must consists of the following :- 1no. Suction Regulator and 2nos. 2000ml polysulphone collection jar and both to be mounted on a trolley. Suction Regulator : Suction regulator should be supplied with a safety jar.

Supply installation testing and commissioning of Medical gas hose assemblies : High pressure Hose antistatic duly colour coded for Oxygen , Nitrous Oxide, Medical Air and Vacuum.

Low Pressure Silicon Rubber tube

Bed Head Horizontal 1200mm Wall Panel: Supply installation testing and commissioning of Horizontal Bed Head Panel.

SITC of Indigenous Single Arm Aneasthetic Pendant : Supply and Installation of Single Arm Aneasthetic Pendant (complete) .

SITC of Indigenous Double Arm Surgeon Pendant : Supply and Installation of Double Arm Surgeon Pendant (complete) .

SITC of Electrical Control Panel for Air & Vacuum system (Cascading / seq. ) with single phase preventer and time totalizer with Electrical wiring.

Electric wiring inside the gas manifold and plant room (Hospital will provide three phase power cable at one point)

Isolation Valves : .Supply installation testing and commissioning of Isolation Valve. 12mm

Isolation Valves : .Supply installation testing and commissioning of Isolation Valve. 15mm

Isolation Valves : .Supply installation testing and commissioning of Isolation Valve. 22mm

Isolation Valves : .Supply installation testing and commissioning of Isolation Valve. 28mm

Isolation Valves : .Supply installation testing and commissioning of Isolation Valve. 42mm

Isolation Valves : .Supply installation testing and commissioning of Isolation Valve. 54mm

FIRE FIGHTING SYSTEM WORK

Supply, Erection, Testing & Commissioning of Electrical Motor Driven Main Pump of horizontal centrifugal end suction backpull out type with gland packing and capable to deliver 2280 LPM at 70 MWC. The pump shall be coupled to TEFC motor of suitable HP with speed of 2900 RPM and complete set shall be mounted on common base frame. MAIN PUMP - 2280LPM AT 70MWC (KIRLOSKAR)

Supply, Erection, Testing & Commissioning of Electrical motor driven Jockey Pump of horizontal centrifugal end suction backpull out type with gland packing and capable to deliver 180 LPM at 70 MWC. The pump shall be coupled to TEFC motor of suitable HP with speed of 2900RPM and complete set shall mounted on common base frame. Electrical motor driven Jockey pump of horizontal centrifugal end suction backpull out type with gland packing and capable to deliver 180LPM at 70M WC. The pump shall be coupled to TEFC motor of suitable HP with speed of 2900RPM ,complete.Kirloskar Make Horizontal End Suction Pump in CI Const with Bronze Impeller, Gland Packed, with Kirloskar Make Electric Motor 415V, 3Phase, 50Hz, 9.3 Kw/12.5Hp, 2900 rpm, TEFC Type, Foot Mounted, Baseframe, Coupling, Coupling Guard, AVM Pad - ( Model: DB 32/26 )

Supply, Erection, Testing & Commissioning of Electrical Motor Driven Terrace Pump of horizontal centrifugal end suction backpull out type with gland packing and capable to deliver 900 LPM at 35 MWC. The pump shall be coupled to TEFC motor of suitable HP with speed of 2900 RPM and complete set shall be mounted on common base frame. MAIN PUMP - 900LPM AT 35MWC (KIRLOSKAR)

Control Panel for Main Electric Pump, Jockey Diesel Pump & Terrace Pump with all necessary wiring work including control and instrumentation, etc complete. MCC PANEL

1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing & commissioning of PVC insulated PVC sheathed, steel armoured, aluminium / copper conductor, 1100v grade power cables.The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. (A) 4C X 35Sq.mm for main pump ( aluminum armored)

1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing & commissioning of PVC insulated PVC sheathed, steel armoured, aluminium / copper conductor, 1100v grade power cables.The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. (C) 4C X 16Sq.mm for terrace pump.( aluminum armored)

1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing & commissioning of PVC insulated PVC sheathed, steel armoured, aluminium / copper conductor, 1100v grade power cables.The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. (C) 2C X 1.5Sq.mm for pressure switch (copper unarmored)

1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing & commissioning of PVC insulated PVC sheathed, steel armoured, aluminium / copper conductor, 1100v grade power cables.The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. (D) 6C X 1.5Sq.mm for diesel engine (copper unarmored)

Supplying, installing, testing and commissioning of M.S.Pipes conforming to IS:1239 Pt - I Heavy Grade Class-C for 15NB to 150NB and IS:3589 Gr 410 ERW Pipe(min 6mm thick) for 200NB & Above with suitable type Pipe fittings such as Reducers, Tees, elbows, flanges. including cutting, grooving, Welding, fixing in / on walls, ceiling by using suitable supports etc, as per drawings with painting as PO Red as per shade 536 of IS:5 MS BLACK PIPE "C" CLASS - IS:3589/Gr.330 200NB MS BLACK PIPE "C" CLASS - 200mm,

Supplying, installing, testing and commissioning of M.S.Pipes conforming to IS:1239 Pt - I Heavy Grade Class-C for 15NB to 150NB and IS:3589 Gr 410 ERW Pipe(min 6mm thick) for 200NB & Above with suitable type Pipe fittings such as Reducers, Tees, elbows, flanges. including cutting, grooving, Welding, fixing in / on walls, ceiling by using suitable supports etc, as per drawings with painting as PO Red as per shade 536 of IS:5 MS BLACK PIPE "C" CLASS - IS:3589/Gr.330 150NB MS BLACK PIPE "C" CLASS - 150mm,

Providing & fixing S.S single headed Yard Hydrant Valve with 80 N.B. flanged inlet, brass spindle controlled 63mm dia female instantaneous outlet type. S.S coupling, blank cap, chain, twist release type lug & all accessories Complete. SS SINGLE HYDRANT VALVE

Providing and fixing 63mm dia instantaneous pattern Branch Short S.S pipe, 20 mm dia nozzle conforming to IS 903, suitable for inter connection to hose pipe coupling complete as required. SS BRANCH PIPE

63mm dia Hose pipe Controlled Percolating Hose as per IS 8423 Type-1 15 M X 1 No. standard length including gun metal male and female Coupling duly bound with aluminium wire, etc. CP HOSE With SS COUPLING Size:63mmx15M WITH ISI MARK

Providing and fixing weather proof lockable Cabinet of size not less than 750 x 600 x 250 mm made out of MS sheet of 16 gauge thickness having central opening and 4 mm thick glazed glass doors (Two nos.) suitably marked FIRE on the outside. MS Hose Cabinet 750x600x250 mm

Supply and installation of 4 Way Fire Brigade Inlet connection in Mains near suitable location with all other accessories located in Fire Water Line. 4 WAY FBI CI BODY

Supply and installation of Fire Brigade drawout connection from with 100NB dia DRAW OUT CONNECTION (SINGLE WAY AS NI 112)

Supplying , installing, testing and commissioning of C.I. Butterfly Valves of PN 16 rating as per IS:13095 of following dia including necessary fittings like Companion flanges,nut ,bolt & gaskets etc. complete. 150NB Butterfly Valve Wafer Type, CI Body, SS Shaft, SG Iron Disc, SS Seating Ring, EPDM Seat, IS 13095, PN16 Pressure Rating (Lever Operated) -150NB

Supplying , installing, testing and commissioning of C.I. Butterfly Valves of PN 1.6 rating as per IS:13095 of following dia including necessary fittings like Companion flanges,nut ,bolt & gaskets etc. complete. (a) 100NB Cast Iron Dual Plate Wafer Type Check Valve - 100NB Butterfly Valve Wafer Type, CI Body, SS Shaft, SG Iron Disc, SS Seating Ring, EPDM Seat, IS 13095, PN16 Pressure Rating (Lever Operated) -150NB

Supplying , installing, testing and commissioning of C.I. Butterfly Valves of PN 16 rating as per IS:13095 of following dia including necessary fittings like Companion flanges,nut ,bolt & gaskets etc. complete. Butterfly Valve Wafer Type, CI Body, SS Shaft, SG Iron Disc, SS Seating Ring, EPDM Seat, IS 13095, PN16 Pressure Rating (Lever Operated) -80NB

Supplying, installing and testing of C.I. Dual Plate Wafer Type Check Valve of PN 16 rating including necessary fittings like Companion flanges,nut ,bolt & gaskets etc. complete. (a) 150NB Cast Iron Dual Plate Wafer Type Check Valve - 150NB

Supplying, installing and testing of C.I. Dual Plate Wafer Type Check Valve of PN 16 rating including necessary fittings like Companion flanges,nut ,bolt & gaskets etc. complete 100NB

Supplying & Fixing of Pressure Switches of suitable range (0-16Kg/cm^2) complete for isolation and fittings such as unions / elbows / reducers etc. Pressure Switch (RT-116

Supplying & Fixing of Pressure Gauge of suitable range (0-16Kg/cm^2) complete for isolation and fittings such as unions / elbows / reducers etc. Pressure Guage - 100mm dia

Supply and installation of foot valve 150 mm

Supply and installation of foot valve 100 mm

SITC of MS fabricated Air Vessel at pump room about 250mm dia and 1500mm high on MS stand with necessary cut off drain and air release arrangements and leading the drain pipe to the sump at pump room. AIR VESSEL / AIR CUSHION TANK - 250MM

Resilient rubber neoprene lined single arch Vibration Eliminators suitable for raw water up to 70 deg.C temperature working pressure 15 Kg per square centimetre. 150NB EXPENSION/JOINT/RUBBER BELLOW - 150MM

Resilient rubber neoprene lined single arch Vibration Eliminators suitable for raw water up to 70 deg.C temperature working pressure 15 Kg per square centimetre. 100NB EXPENSION/JOINT/RUBBER BELLOW - 100MM

Cast Iron Body flanged 'Y'-type Strainer with SS Perforated screen complete with suitable flanges, nuts, bolts, gaskets etc. complete. 150NB Cast Iron Y-Type Strainer with SS304 Perforated Screen (Flanged)- 150NB

Cast Iron Body flanged 'Y'-type Strainer with SS Perforated screen complete with suitable flanges, nuts, bolts, gaskets etc. complete. 100NB Cast Iron Y-Type Strainer with SS304 Perforated Screen (Flanged)- 100NB

Supplying and fixing of perforated G.I.sheet CABLE TRAY with neccessory angle iron suspension supports, anchor fasteners etc. complete. Maximum height of suspension shall not exceed 500 mm. (a) 40mm x 300mm x 40mm and 2mm thick. GI Cable Tray 300mmx40mmx2th

Supplying and fixing of perforated G.I.sheet CABLE TRAY with neccessory angle iron suspension supports, anchor fasteners etc. complete. Maximum height of suspension shall not exceed 500 mm. (b) 40mm x 150mm x 40mm and 2mm thick. GI Cable Tray 150mmx40mmx2th

Sand filling Excavating and earthmoving services (Civil work)

Coating & Wrapping for underground pipe Wrapping Tape(150mm wide x 4mm thick) Wrapping & Coating

Supply, laying, testing and commissioning of Copper wire. 2C X 1.5Sq.mm (copper unarmored)

Supply, installation, testing and commissioning of MS body manual call point.

Supplying, installing, testing and commissioning of conventional Sprinkler quartzoid bulb type with 15mm screwed end connection of K 80 and orifice shall not be less than 12.7mm. Sprinklers with Chrome finished. (a) Pendent Sprinkler 68 deg. C PENDENT SPRINKLER-68DEG

Supply, installation, testing and commissioning of MS body electronic sounder ( hooter ).

Supply, installation, testing and commissioning of Somke Detector.

Supplying , installing, testing and commissioning of Bronze Ball valve with (suitable for test pressure of not less than 15 Kg / sqcm of the following size including providing necessary union / flange. 25NB Bronze Ball Valve (Screwed) - 25mm Dia

Supply and installation testing and commissioning of Pressure Gauge of suitable range (0-16 bar), 100 mm diameter dial for pump sets completes with necessary Ball valves, siphon, Fittings like unions / colors / reducers etc. Pressure Guage - 100mm dia

Mechanical Foam type fire extinguisher 9Lts. Capacity, stored pressure type controllable discharge mechanism. Mechanical Foam type fire extinguisher 9Lts. Capacity, stored pressure type

ABC powder type fire extinguisher of 4 Kgs. Capacity. Fire Extinguisher ABC Type Capacity 4Kg

Carbon-di- oxide type fire extinguisher of 4.5 kgs. Capacity. Fire Extinguisher Water CO2 Â type Capacity 9Ltr

First Aid Hose Reel of 180 swinging type with 30 mts long and 19 mm dia heavy duty PVC hose, 20 mm dia globe valve stop cock, terminating with S.S coupling & triple purpose nozzle of 6mm outlet with shut off cock. HOSE REEL DRUM WITH 19 MM 30MTR RUBBER HOSE &GM NOZZLE

Supply, installation, testing and commissioning of main fire alarm panel supply source (230AC 50 Hz and 24 V DC) 24V out put supply for detector. fault indication open, short circuit in detector line. visual indication fire, fault, open, short & system on. 4 Zone

Cast Iron Body flanged 'Y'-type Strainer with SS Perforated screen complete with suitable flanges, nuts, bolts, gaskets etc. complete. (a) 150NB Cast Iron Y-Type Strainer with SS304 Perforated Screen (Flanged)- 150NB

Supply, installation, testing and commissioning of main fire alarm panel supply source (230AC 50 Hz and 24 V DC) 24V out put supply for detector. fault indication open, short circuit in detector line. visual indication fire, fault, open, short & system on. 6 Zone

Supply, erection, testing and commissioning of Fire Hose Door (FHC)door size (approx) 2100 mm x 1200 mm, 14 SWG, 4mm Glass with hinged door shutter and frame and fabricated out of 14 SWG sheet steel, fitted with 4mm thick toughened glass in the front including finishing with powder coat painting complete. Ms Double Hose Door 2100X1200

Supply, installation, testing and commissioning of main fire alarm panel supply source (230AC 50 Hz and 24 V DC) 24V out put supply for detector. fault indication open, short circuit in detector line. visual indication fire, fault, open, short & system on. Repeater 10 Zone

Wall Panel with 50mm thick Panel PUF Sandwiched Double skin constructed with EGP (Electrogalvanized steel Sheet) panels having a flame resistance to BS 1142 with proper supports .

Ceiling Panel with 30mm thick Panel PUF Sandwiched Double skin constructed with EGP (Electrogalvanized steel Sheet) panels having a flame resistance to BS 1142 with proper supports .

SITC OF OPERATION THEATRE AS PER FOLLOWING

The Operation theatre floor finish should be laid with 2 mm antistatic seamless conductive PVC sheet on a semi-conductive adhesive base. The floor should be scratch resistant, fire resistant, chemical resistant, non-corrosive, slip resistant, smooth, anti fungi, antimicrobial impervious material conductive enough to dissipate static electricity but not conductive enough to endanger personnel from electric shock. The floor finish should pass over a concealed cover former and continue up the wall for 100mm. The floor should be provided flat to within a tolerance of ±3mm over any 3 meter area.

EXHAUST AIR GRILL The openable and cleanable return-air exhaust GRILL should be provided in the operation theater. Designed flow rate should not be less than 800 m3/hr. Distribution of exhaust air .

X-RAY FILM VIEWER The two (2)-plate viewing LED type high frequency fluorescent lamps X-Ray Viewing Screen . Each plate should be able to illuminate films upto 14”x17” size. ‘Dimming is controlled using dimming ballast and PCB mounted inside the box. The mounting of the Screen should be installed flushed with Operation theatre wall to avoid dust accumulation and microbial growth and ease of cleaning.

Filling of Joints ,Cavity and imported Antibacterial paint. Filling of all joints and cavaties with Metallic Epoxy filler and sanded flush to provide a jointless finish and then prayed with a water based liquid plastic aspetic and self - sterlizing wall coating system to d d.f.t. of 300 microns with primer.

PERIPHERAL LIGHT CUM CLEAN ROOM LUMINARIES The fluorescent lamps 54 W 16mm Ø- 3 nos / Non-hygroscopic high glow low power LED based /digital blast peripheral lights (1’x2’) having high quality low wattage LED lighting system with highly spectacular anodized Aluminum reflectors and optical antiglare system for adjustable light distribution. Luminaire cover made of highly resistant, disinfectant proof laminated safety glass with fine grained surface, glass pane with white powder coated steel frame. Luminaire body made of sheet steel, white, powder coated supplied ready for connection.

OPERATION THEATRE CONTROL PANEL (DIGITAL TOUCH PANEL OPPTIONAL ) The OT Control Panel should be designed to cope with changing technology and equipment in operating environments. Control panel should be user friendly and ease of operating and maintaining purpose. The Control Panel should be configured to incorporate all the services required by the staff in the Operation theatre. It should be mounted flush in the theatre wall. The Control Panel should comprise of following Six (6) services in addition to Instruction board, Communication interfaces etc.

AIR CANOPY with provision for LAMINAR AIR FLOW SYSTEM (AIR MANAGEMENT SYSTEM) Supply, Installation , testing , commissioning of air planum unit the system cunstructed with a plenum box made of powder coated aluminium sheet 2mm that will introduce the highest air quality in to the operation theatre . Air diffused in to the room uniformly over the total area through Poliyester filament .the air light diffusers should be installed in a manner . which allow them to be removed for access air filter the laminar flow ceiling is able to provide integrated frame support system case of maintenance and long life system. HEPA filter having dust spot efficiency of 99.99% 0.3 micron under tight control of bacteria infection system size planum (canopy) of 1800x2400.

SURGEON PENDANT • Should have one shelves of load bearing capacity of minimum 100 Kg. arm Rotation should be atleast 330o& Service-head rotation should be atleast 330o Should have a provision of mounting the equipment Provision for Service Points/Outlets : • Should have a minimum of 4 to 6 no.’s of standard Medical Gas Service outlets, data socket & atleast 6 no. of standard duplex conditioned Electrical Service outlets.

ANEASTHESIA PENDANT • 900 mm moveable arms with 330 deg. Horizontal movement. The weight carrying capacity of the arm should not be less than 80-90 KG. arm should be capable of 330 degrees of rotation, which can be easily adjusted to suit the desired mode of operation. The Pendant Service Head should be supplied with provision for medical gas terminal units 6 to 8 no.. and 5/15 Amps. Sockets.

SUPPORT STRUCTURE Supporting structure required for installing O.T wall and ceiling panel on the walls of the operating room should be galvanized steel profile. The inner surface frame should be constructed with at least 1.60mm thick . The inner surface walls should be fixed to the brick wall with essential supports. There should be minimum possible cavity/gap in between the solid and steel walls.

DISTRIBUTION BOARD and ELECTRICAL WIRING, CONDUITING WITH FIXTURES INSIDE THE OPERATION THEATRE • Electrical Distribution Board along with all high voltage equipment should be installed in a separate enclosure. Electric Distribution Panel, UPS, Transformers, Mains, Relays, Circuit protective equipment, for all circuits of Operation theatre shall be installed in the remote cabinet. Wiring for 250 volts single phase and neutral 6/16 Amps switched socket outlet with 3 sq.mm and 2.5 sq.mm PVC insulated copper conductor 1100 volts stranded flexible wires should be concealed with conduit.

AIR RELEASE DAMPER Air release damper cascade Pressure stabilizer having a stainless steel blades to control room air pressureas .

ELECTRICAL WIRING, CONDUITING WITH FIXTURES INSIDE THE OPERATION THEATRE Laying of PVC conduits, Modular Switch Boxes, Modular Switches-sockets, Power and Light wiring including Earthing wire for all the lighting controls, Pendant and other equipment fixtures and fittings inside the theatre Wiring with low leakage current wires of FRLS wires as per requirements. Wiring for 250 volts single phase and neutral 6/16 Amps switched socket outlet with 3 sq.mm and 2.5 sq.mm PVC insulated copper conductor 1100 volts stranded flexible wires to be concealed with conduit.

Stainless Steel Scrub Sink (2 Bay) Sensor Operated- The scrub station is made of high grade stainless steel and seamless welded construction, polished to a stain finish. The scrub sinks to be provided with built-in with timer setting of 1 to 10 minutes depending on customer requirement.

ELECTRICAL WORK FOR O.T. Supply and installation of (Make: Sterile Air/ZECO/UNIQUE ARIFLOW/Balance Air/ETA) AHU Unit on the roof (3500 CFM, 115MM) includes lifting shifting on site. Foundation for AHU be provided by client. The AHU is designed for 25% fresh Air. The Ahu is fitted with coil section with 8 RD DX Non VRF Coil. (Single Circuit) Prefilter and Micro Filter fitted in AHU. AHU CAN PROVIDE 18-20 DEGREE CELCIUS IN THE ROOM.

Supply and installation of starter panel for Ahu Unit (Specification attached)

Supply and installation of DAIKIN/CARRIER/VOLTAS Cooling only Non VRF outdoor unit of 8.5TR capacity with twinning kit including lifting shifting on site and outdoor unit frames. Based on R410

Supply installation of Control Panel and thermostat for temperature setting and operation.

Supply installation of suction and discharge copper pipe to connect outdoor unit. Ahu Kits and the AHU

Supply installation of comunication cable of 2.5 sqmm 4 core copper shielded cable laid in 1" PVC pipe (Make of communication cable Polycab/USHA/RR cables

Supply installation of 40mm drain tubing (6Kg/Sqinch/) (Make : Supreme/Finolex) with 6mm insulatino.

Supply, site fabrication and installation of 22 guage (0.711mm) Alluminium ducting for supply and return ducting.

Canvas connection.

Supply and installation of 19mm thick Anti-Microbial Thermoisolate class o Nitrile Rubber insulation for supply duct and return duct

Cable tray 300 mm

ELECTRICAL WORK

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required Above 120 sq. mm and upto 400 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 400 sq. mm (82mm)

Supplying and making outdoor cable and termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required 120 sq. mm

Supplying and fixing of light class G.I. pipe of 100 mm dia. (nominal) 3 metres length along the pole for protection of under ground cable as required.

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. Above 6.5 meter and upto 8.0 meter

Providing and making steel pole collar with cement concrete (1 cement : 3 coarse sand : 6 stone aggregate 20 mm) of specified size and shape including form work, plastering if required, curing etc. as required. (volume of pole/ pipe not to be deducted)

Supplying and erection of galvanised stay set for 11 KV over head lines complete with 19/ 20 mm dia X 1.8 metres long stay rod, anchor plate of size 45 cm X 45 cm X 7.5 mm thick, thimble, stay clamps, turn buckle ( 20 mm X 600 mm ), 7/ 4.00 mm dia G.I. stay wire and 11 KV strain insulator etc in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling etc. as required.

Supplying of two lengths of channel iron 75 mm X 40 mm X 6 mm (7.14 kg per metre) double pole cross arm for three wire 11KV over head line conductors complete with through bolts and nuts for clamping to the poles, 50 mm X 6 mm M.S. flats welded on one side to the channel iron and with bolts and nuts on the other side for tying the cross arms together, including drilling holes for insulator pins/ fittings, bolts, nuts and washers etc (as per drawing) and painting with primer and finish paint as required.

Supplying and erection of a set of cross bracing FRLSame work for 11 KV over head line double pole structure having four members fabricated out of 50 mm X 50 mm X 6 mm angle iron to form a rectangle of minimum size 1400 mm width X 2500 mm height , complete with 50 mm X 6mm M.S. flat iron clamps, bolts and nuts including drilling holes for insulator pins, bolts and nuts etc (as per drawing) and painting with primer and finish paint as required.

Erection of double pole 3 wire cross arm for 11KV/ 22KV/ 33 KV over head lines as required.

Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required.

Supplying and erection of 11 KV disc insulator for 11 KV over head lines with galvanised insulator fittings, ball and socket type and complete with galvanised strain clamps, bolts, nuts, washers etc. as required.

Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.

Supplying, installing by suspension on ceiling, testing and commissioning of following capacity Sandwich Type Rising Mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. 1600 A 50kA SC for 1 sec

Supplying, installing by suspension on ceiling, testing and commissioning of following capacity Sandwich Type Rising Mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. 2500 A 50kA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity End Feed Unit for the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required 800 A 50kA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity End Feed Unit for the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required 1250 A 50kA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required 500 A 50kA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required 630 A 50kA SC for 1 sec

Supply,of following sizes of PVC sheathed LT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes. 3.5c x 500 sq.mm cable

Supply,of following sizes of PVC sheathed LT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes. 3.5c x 240 sq.mm cable

Supply,of following sizes of PVC sheathed LT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes. 3.5c x 185 sq.mm cable

Supply,of following sizes of PVC sheathed LT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes. 3.5c x 70 sq.mm cable

Supply,of following sizes of PVC sheathed LT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes. 3.5c x 50 sq.mm cable

Supply,of following sizes of PVC sheathed LT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes. 4c x16 sq.mm cable

Supply,of following sizes of PVC sheathed LT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes. 4c x10 sq.mm cable

Supply,of following sizes of PVC sheathed LT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes. 4c x 6 sq.mm cable

Supply,of following sizes of PVC sheathed HT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes. 3.5 C X 240 sq.mm cable

Supply of Decorative gate light Globe shaped post top lantern in high grade unbreakable polycarbonate material suitable for retrofit LED (LHFXBON1TN5Q020) lamp B22 base. Upto 20 W.complet in all aspects as per direction of Engineer in charge. (Rate taken from Havells price list w.e.f. Jan 2020).

Supply of LED post Top with aluminium enclosure, powered with high power LEDs 72 W as light source and die casted heat sink exhibiting classic Victorian look with symmetrical light distribution, suspended mounting arrangement and excellent heat dissipation for long life standard make (Havells EROSPT72WLED757PSYMTOPC) complete in all aspects as per direction of Engineer in Charge. (Rate taken from Havells price list w.e.f. Jan 2020).

Supplying installation, testing & commissioning of 415 V, 3 ph, 50Hz, 4wire system, sheet steel clad, dust & vermin proof cubical & indoor type floor mounted, free standing extendible type main LT panel with IP-42 Protection, compartmentalized design & fabricated out of 2 mm/1.6mm CRCA Sheet steel complete with Al.Bus bar electrical interlocks as per the various status of all the equipment indicates on the drawing.Providing & fixing of base plate chennel, p/f the following complete with earth bus bar throughout the length of the panel, terminal arrengment for incoming / outgoings cables & also outgoing termination for verious size of cables, the incoming & outgoing feeders shall be accommodated in a modular multi-tier arrenment adiquate size bus duct /cable Alliey, sign writing painting, earthing, numbring, danger plat etc. complet as requir as per specification & drawing . INCOMING 2 nos. 1250A 415V, 4P 50kA EDO ACB With microprocessor based release having O/L,S/C OUTGOING ,E/F , RPR, O/V, U/V protection & ON/OFF/TRIP Indication with MCB 1 nos. 1600A 415V, 4P 50kA EDO ACB With microprocessor based release having O/L,S/C ,E/F , RPR, O/V, U/V protection & ON/OFF/TRIP Indication with MCB 1 nos. 1000A 415V, 4P 50kA EDO ACB With microprocessor based release having O/L,S/C ,E/F , RPR, O/V, U/V protection & ON/OFF/TRIP Indication with MCB 3 nos. Digital type power analyser meters to show (V,A,KWh,KVAh,KW,KVA,KVAR,PF,Hz,harmonic) with cast resin CTs. & communication port. 3 set of LED phase indicating Lamps with MCB Protection 3 nos. trip circuit supervision relays. 2 nos. 225KVAR capacitor bank with 630 apm TP MCCB of 50KA,with one set of indicating lights. 3 nos.electronic type dual type automatic power factor correction relay. 3 nos TPN surge protection device of class 1&2 3nos restricted earth fault . BUSBARS 2 Set of TPN AL bus bar of minimum of 2000A capacity with heat shrinkable coloured slabs & i/c DMC/SMC Bus bars suports at required intervals complete for cross section, size suports & their spacing etc. for with standing fault level of 36KA for 1 sec. BUS COUPLER 1 nos. 2500A 415 V, 4P 36KA EDO ACB with in built O/L, S/C protection & ON/OFF/TRIP indication with MCB 4 nos. 1000A 415V, TP+N ACB of 50KA with microprocessor based release having O/L, S/C protection & digital multi function to show (V,A,KWh,KVAH,KW,KVA,KVAR,PF,Hz ) with cast resin CTs.& comunication port. 3 nos. 630A 415V, TP+N MCCB of 50KA with microprocessor based release having O/L, S/C protection & digital multi function to show (V,A,KWh,KVAH,KW,KVA,KVAR,PF,Hz ) with cast resin CTs.& comunication port. 1 nos. 630A 415V, TP+N MCCB of 50KA with microprocessor based release having digital multi function to show (V,A,KWh,KVAH,KW,KVA,KVAR,PF,Hz) with cast resin CTs.& comunication port. 1 nos. 400A, 415V, TP+N MCCB of 50KA with microprocessor based release having O/L, S/C protection & digital multi function to show (V,A,KWh,KVAH,KW,KVA,KVAR,PF,Hz ) with cast resin CTs.& comunication port. 3 nos. 160A 415V, TP+N MCCB of 50KA with microprocessor based release having O/L, S/C protection & digital multi function to show (V,A,KWh,KVAH,KW,KVA,KVAR,PF,Hz ) with cast resin CTs.& comunication port. 1 no. 125A 415V, TP+N MCCB of 50KA with microprocessor based release having O/L, S/C protection & digital multi function to show (V,A,KWh,KVAH,KW,KVA,KVAR,PF,Hz ) with cast resin CTs.& comunication port. 1 no. 80A 415V, TP+N MCCB of 50KA with microprocessor based release having O/L, S/C protection & digital multi function to show (V,A,KWh,KVAH,KW,KVA,KVAR,PF,Hz ) with cast resin CTs.& comunication port. 3 nos. 63A 415V, TP+N MCCB of 50KA with microprocessor based release having O/L, S/C protection & digital multi function to show (V,A,KWh,KVAH,KW,KVA,KVAR,PF,Hz ) with cast resin CTs.& comunication port. 1 nos. 40A 415V, TP+N MCCB of 36KA with microprocessor based release having O/L, S/C protection & digital multi function to show (V,A,KWh,KVAH,KW,KVA,KVAR,PF,Hz ) with cast resin CTs.& comunication port. 2 nos. 25A 415V, TP+N MCCB of 50KA with microprocessor based release having O/L, S/C protection & digital multi function to show (V,A,KWh,KVAH,KW,KVA,KVAR,PF,Hz ) with cast resin CTs.& comunication port.

LIFT PANEL INCOMER 1 nos. 160A, 415V, 4P ATS. 1 nos. 160A 415V, Ics=25KA, 4P MCCB with microprocessor release having O/L, S/C E/F,O/V & U/V protection. 1 nos. Digital type multi function meters to show (V,A,KWh,KVAH,KW,KVA,PF,Hz) with cast resin CTs & communication port . 1 Set of phase indicating lamp with MCB 1 nosTPN surge protection device of class 1& 2 BUSBAR 1set of TPN Al. Bus bar of minimum of 200A capacity with heat shrinkable coloured sleeves & i/c DMC/SMC Busbars suports at required Intervals complete for cross section, size suports & their spacing etc. for with standing fault level of 25KA for 1 sec. OUTGOING OUTGOING 10 nos. 63A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection & digital multi function (V+A+Hz ) with a set of cast resin CTs.

Supplying, fixing, testing & commissioning of 415V ,3Phase 50Hz, 4wire system,sheet steel clad,dust & vermin proof cubical & indoor type floor mounted, free standing Main Distribution Board with IP - 42 protection, compartmentalized design and fabricated out of 2mm/1.6mm CRCA sheet steel complete with aluminium Bus Bars, Providing & Fixing of base plate /channel, P/F the following Switchgears,complete with earth Bus Bar throughout the length of the panel,terminal arrangement for incomings/outgoings cables and also outgoing terminations for various sizes of cables,the incoming and outgoing feeders shall be accommodated in a modular multi-tier arrangement,adequate size bus duct/cable alley, Sign writing,Painting,Earthing,Numbering,Danger plate etc. Compleete as requried,numbering, danger plate etc. complete as required as per specification and drawing. SMDB-GF INCOMER: 1 nos. 630A 415V, Ics=25KA, 4P MCCB with microprocessor release having O/L, S/C E/F,O/V & U/V protection. 1 nos. Digital type multi function meters (V+A+Hz) with cast resin CTs 600/5A. 1 Set of phase indicating lamp with MCB 1 nos TPN surge protection device of class 1& 2 BUSBAR 800A TPN Bus bar of aluminimum alloy. OUTGOING 3 nos. 20A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 3 nos. 25A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 1 nos. 32A 415V, TP+N MCCB of 25KA with microprocesso r based release having O/L, S/C protection. 1 nos. 50A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 2 nos. 63A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 7 nos. 80A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 3 nos. 160A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection.

ESMDB-B INCOMER: 1 nos. 63A 415V, Ics=25KA, 4P MCCB with microprocessor release having O/L, S/C E/F,O/V & U/V protection. 1 nos. Digital type multi function meters (V+A+Hz) with cast resin CTs 100/5A. 1 Set of phase indicating lamp with MCB 1 nosTPN surge protection device of class 1& 2 BUSBAR 100A TPN Bus bar of aluminimum alloy. OUTGOING 1 nos. 25A 230V, SP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 9 nos. 25A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection.

ESMDB-SF INCOMER: 1 nos. 400A 415V, Ics=25KA, 4P MCCB with microprocessor release having O/L, S/C E/F,O/V & U/V protection. 1 nos. Digital type multi function meters (V+A+Hz) with cast resin CTs 400/5A.1 Set of phase indicating lamp with MCB 1 nos TPN surge protection device of class 1& 2 BUSBAR 630A TPN Bus bar of aluminimum alloy. OUTGOING 8 nos. 63A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 2 nos. 40A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 2 nos. 32A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 2 nos. 20A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection.

ESMDB-4F, INCOMER: 1 nos. 1000A 415V, Ics=25KA, 4P ACB with microprocessor release having O/L, S/C E/F,O/V & U/V protection. 1 nos. 1000A 4P Automatic Transfer Switch 1 nos. Digital type multi function meters (V+A+Hz) with cast resin CTs 1000/5A. 1 Set of phase indicating lamp with MCB 1 nos TPN surge protection device of class 1& 2 BUSBAR 1250A TPN Bus bar of aluminimum a lloy. OUTGOING 2 nos. 400A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 4 nos. 160A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 2 nos. 100A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 3 nos. 63A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 1 no. 40A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 4 nos. 25A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection.

Material and labour for CSS foundation of size 2.5x2.5x0.90m, brick masonry work in 1:6 with PCC 1:4:8 in top of plateform including feeling of boulder brick bats as directed by Engineer-in-charge.

Supply of 8.5 m long Tublor pole SP-23 with base plate and top cover plate complete in all respect.

AUTOMATIC POWER FACTOR CONTROL PANEL(EEP) 500KVAR,IP Rating IP33, IP40, IP44, IP54, IP55, Single phase,three phase

Providing & Fixing Lightning Arresters System (Building protection)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. Group B

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.

Wiring for light/power plug with 2x4 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring fir curcuit/ submain wiring alongwith earth wire the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring fir curcuit/ submain wiring alongwith earth wire the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring fir curcuit/ submain wiring alongwith earth wire the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Wiring fir curcuit/ submain wiring alongwith earth wire the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair

Supplying and fixing of following sizes of PVC conduit along with accessories in surface / recess including painting in case of surface conduit, or cuttting the wall and making good the same in case of recessed conduit as required.20 mm

Supplying and fixing of following sizes of PVC conduit along with accessories in surface / recess including painting in case of surface conduit, or cuttting the wall and making good the same in case of recessed conduit as required. 25mm

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required. 75 mm X 75 mm X 60 mm deep

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet

Telephone socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing 3 pin, 5 amp. ceilling rose on the existing junction box/ wooden block including connection etc. as required

Supplying and flxing brass batten/angle holder including connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling / wall, including connection with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq, mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation of exhaust fan upto 450 mm sweep in the existingopening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required.

Extra for fixing louvers/shutters complete with frame for a exhaust fan of all sizes.

upplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door

upplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way (4 + 18), Double door

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissoning etc. as required. 63 amps

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 600 mm width X 50 mm depth X 2.0 mm thickness

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc.with charcoal/ coke and salt as required..

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supply of AC 230/250 volts, 50 HZ energy efficient ceiling fan with standard down rod, blades, 3 nos. caps Model-ES-50 50/Velocity/Velocity HS (1200 mm Sweep) etc. complete in all aspects as per direction of Engineer in Charge. (Make- HAVELLS ) (Rate taken from Havells price list w.e.f. Jan 2020). 1200 mm sweep

Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete.Model- Turbo Force SP (Make : Havells) 300 mm sweep 900 rpm ,complete in all aspects as per direction of Engineer in Charge. (Rate taken from Havells price list w.e.f. Jan 2020). 300 mm sweep 900 rpm

Supply of Ceiling Light Aluminium frame Environmental friendly, new generation,aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source, suitable for Armstrong/Grid ceiling (600X600mm) with electronic driver & high Brightness. complete in all aspects like Ballast , housing connecting wire etc. as per direction of Engineer in Charge. (Rate taken from Havells price list w.e.f. Jan 2020). Make-Havells

Supply & fixing of Recess Ceiling Light OCTANE LED PANEL ROUND Slim, compact, auminum die cast edge lit panel. Recess mounted round fixture (110MM DIA) ith opal diffuser and separate electronic driver. 6W LED, 6500k /4000k/3000K (Code- LHEBHDP6IZ1W006) as per direction of Engineer in Charge. (Rate taken from Havells price list w.e.f. 2018).

Supply & fixing of NU Bulb LED Mirror Light -9W (LHLDEUECNL8R009) ,6500k connecting wire etc.of standard make (Havell's) as per direction of Engineer in Charge. (Rate taken from Havells price list w.e.f. Jan 2020).

Supply and fixing of Power coated Regal Batten type luminaire 1x36W FTL HF 240v,50Hz etc, (Code- LHFXBIG1IN1W036) ,with electronic ballast, complet in all aspects as per direction of Engineer in charge. (Rate taken from Havells price list w.e.f. 2018).

Supply & fixing of Wall Mounted Personal LED Luminaire 31W, 5700k Cat No- LW04-411-XXX-57-XX (Rate taken from Wipro price list w.e.f. 2017).

SUPPLY OF LED Glass Bulb B22, 15 W ,6000k /4000k/3000K ,230/250 Volt,50 HZ ETC, complete in all aspects as per direction of Engineer in Charge.

Supply and fixing of BULK HEAD light- 1 X 8 W CFL bulk head in die cast aluminium housing & frosted glasses complet in all aspects as per direction of Engineer in charge.

Supply and fixing of C Cube Nurse call System, (NCS) with complete all accessories.

Supply of 900 KVA DG Set Comprising of KOELGREEN Make above model Diesel Engine- DV16ETAG1, Alternator Three Phase 900 KVA/ 720 KW complete with standard Accessories complete in all aspects as per direction of Engineer In-charge with exhaust chimney and fuel system of appropiate size and standard.

Supply of 500 KVA DG Set Comprising of KOELGREEN Make above model Diesel Engine- DV10TAG1 , Alternator Three Phase 500 KVA/ 400 KW complete with standard Accessories complete in all aspects as per direction of Engineer In-charge

Supply , Installtion , Testing and comissioning of CAT 6 UTP cable solid copper conductors Approved Makes: Dlink/Belden/ Siemon/Panduit/Der Wiser/Molex

Supply , Installtion , Testing and comissioning of CAT6 information outlet (I/O) for Data, Voice & Wi-Fi rack end Approved Makes: Dlink/Belden/ Siemon/Panduit/Der Wiser/Molex

Supply , Installtion , Testing and comissioning of CAT6 patch cord 3 feet for rack side switch termination for user End Approved Makes: Dlink/Belden/ Siemon/Panduit/Der Wiser/Molex

Supply , Installtion , Testing and comissioning of CAT6 patch cord 7 feet for user termination to information outlet Rack End Approved Makes: Dlink/Belden/ Siemon/Panduit/Der Wiser/Molex

Supply , Installtion , Testing and comissioning of 1, 2 and 4 port face plate white for I/O fixing at user side. Approved Makes: Dlink/Belden/ Siemon/Panduit/Der Wiser/Molex

Supply , Installtion , Testing and comissioning of 27U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos of hardware pkts. Approved Makes: MTS/Rittal/APC/APW

Supply and installation ,Testing and Commissioning of off grid solar power plant polycrystalline PV module of rating 300 Wp with 36 cells module mounting structure for PV Module of capacity 25 KW, structure MS with powder coated (MNRE approved) : Ritika solar/vikram solar with micromax battery of 150 Ah (MNRE approved) Luminous/ exide/ amron (for 03 hrs backup) off grid interactive 25 KWA three / 1 phase string inverter with MPPT-UTI, STATCON, UTL, Microtech & luminous complete in all aspects as per directions of engineer- in-charge

SOLAR WATER HEATER Supply and installation ,Testing and Commissioning of 5000 LPD with 5 Collector Flat plate Collectors , Premium Closed Loop SS 304 Tank with HeatExchanger, Circulation Pump, Control Panel, Temperature Pressure, Relief Valves with electrical back up of 2 Kwatt. Complete With prefabricated MS hot dipped galvanized and painted mounting structure. Max. system operating Pressure- 1kg/cm² ,Max Water Temp. 60º C. complete in all aspects as per directions of engineer- in-charge

M/S Shiv Kumar Agarwal

Pundrikaksh Developers Pvt Ltd