Interior Fit-Out works Electrical/ HVAC /FPS and FAS related works for Building-1 at TIZ, Kalamassery, Kochi.

Amount

Wall Acoustic Panel

od131315/2020_2021 : PERFORATED WOODEN PANELS- providing and fixing Perforated Wooden Slats - Melamine Laminated<br>Supply & installation of perforated wooden grooved slats - FR grade, Slats L16-2 - (2mm Slats @16mm pitch) of size 128mm x 2430mm x 16mm thick made out of wood particle, Melamine laminated finish, backlined with acoustical fleece, fixed by using GI channel of 0.5mm thk having 21mm & 27mm width, height 18mm, having flanges of 7mm (installed horizontally -for vertical fixing of slats) spaced at 400mm centers with suitable brackets, GI 18mm channel is perpendicularly to the GI cross sectional channel of 0.45mm thk having a knurled web of 50mm width, height 22mm, having flanges of 15mm is then fixed to the Main channel with the help of connecting clip in direction perpendicular to the Main Channel at every 600mm centers main Channels of web 45mm x 0.9mm thk with two flanges of 15mm each from the soffit at every 1000mm centers with suspender angle of size 25mm x10mm x 0.45mm thk fixed to the soffit with G.I Cleat and metal fasteners as indicated in the drawing. The system is backlined with the acoustical infill synthetic polyfibre 25mm thick (SynthPF 10x25)<br>The Perforated Wooden Slats ceiling module perimeter is covered with 12mm thick plywood with laminated finish, <br>color as per the choice of Client / Architect, with necessary supports as indicated in the drawing<br>Technical Parameters of the Perforated Wooden Slats - Melamine Laminated material <br>• Fire – Class A<br>• Acoustics –NRC 0.7<br>• Climate (OC, RH) – 50,70<br>• Termite resistance – Yes<br>• Light – 75 % <br>• Green – 25 %<br>• Hygience (VoC, Clean room) – Low, Class1<br>Rate inclusive of cost of all the materials, labour, scaffolding, installation and all taxes. Finished area of flooring shall be measured in Sqm for payment. Note - Vendor to submit valid test certificates for the above mentioned technical parameters. Approved manufacturer: Anutone, Armstrong, Top akustic /RPG. Rate including all necessary frames as per drawing.

od131354/2020_2021 : Providing and fixing column /WALL panelling as shown in drawing no. but in general, it shall be made out of aluminium box frame of size 50 x 25 mm - 1.5mm tk at 600mm c/c in both direction. covered with 10 mm thick BWR ply and finished with 1.5 mm thick Laminte of approved shade. including forming pattern and details as in drg. Rate shall include for providing teak wood beadings edge protection and as directed complete with necessary hardwares. Rate shall include for forming a panelling to any shape including circular profile etc. complete.) Rate include 50mm Rockwool insulation 48kg/cm covered with acoustic wooden slats

od131355/2020_2021 : Providing and fixing column /WALL panelling as shown in drawing no. but in general, it shall be made out of aluminium box frame of size 50 x 25 mm - 1.5mm tk at 600mm c/c in both direction. covered with 10 mm thick BWR ply and finished with 1.5 mm thick Laminte of approved shade. including forming pattern and details as in drg. Rate shall include for providing teak wood beadings edge protection and as directed complete with necessary hardwares. Rate shall include for forming a panelling to any shape including circular profile etc. complete.) Rate include 50mm Rockwool insulation 48kg/cm covered with AMF Hera wood wool board finished with wooden slats

od131356/2020_2021 : Providing and fixing column /WALL panelling as shown in drawing no. but in general, it shall be made out of aluminium box frame of size 50 x 25 mm - 1.5mm tk at 600mm c/c in both direction. covered with 10 mm thick BWR ply and finished with Fabric /Leather of approved shade. including forming pattern and details as in drg. Rate shall include for providing teak wood beadings edge protection and as directed complete with necessary hardwares. Rate shall include for forming a panelling to any shape including circular profile etc. complete.Rate include 50mm thick rockwool insulation with 48kg/cum

od131357/2020_2021 : Providing and fixing column /WALL panelling as shown in drawing no. but in general, it shall be made out of aluminium box frame of size 50 x 25 mm - 1.5mm tk at 600mm c/c in both direction. covered with 10 mm thick BWR ply and finished with 1.5 mm thick Laminte of approved shade. including forming pattern and details as in drg. Rate shall include for providing teak wood beadings edge protection and as directed complete with necessary hardwares. Rate shall include for forming a panelling to any shape including circular profile etc. complete.

od131358/2020_2021 : Providing and fixing column /WALL panelling as shown in drawing no. but in general, it shall be made out of aluminium box frame of size 50 x 25 mm - 1.5mm tk at 600mm c/c in both direction. covered with 10 mm thick BWR ply and finished with 1.5 mm thick Laminte of approved shade. including forming pattern and details as in drg. Rate shall include for providing teak wood beadings edge protection and as directed complete with necessary hardwares. Rate shall include for forming a panelling to any shape including circular profile etc. complete.) Rate include 50mm thick rockwool insulation with 48kg/cum50mm Rockwool insulation 48kg/cm covered with AMF Hera wood wool board finished with fabric

od178293/2020_2021 : BLACKOUT SCREEN<br>Providing & fixing vertical black out blinds confirming to following specifications<br>Supplying & fixing Luxaflex /MACC Series / EquiIvalent make Effective Optimized System Roller blinds Shade consists of sanitized treated, resilient and approved sample colour polyester base fabric with high tear strength, Roller Tube, Control Chain, Control Set Left Hand, Control Set Right Hand, Bracket Cover, Chain Connector, O-C Bottom Rail String for conversion Spring, Bottom End Plug, Bottom End Plug Circular, Open Bottom Rail, Tube Bearing Plug etc. The basic rate is Rs.1800/sqmt.

Partition

od131436/2020_2021 : Straight Glazed Partition-Slim line of approved make: Providing and installation of full height straight glass partition from FFL to the bottom of false ceiling and fixing 12mm thick toughened and heat soaked glass and proprietary type anodized aluminium slimline sections of approved make. The sections shall be matt finish natural anodized and shall be a combination of male and female frames on all four sides as per the manufacturers specification. The rate shall be including the cost of all necessary hardwares, anodized aluminium jointing profile on edges of the glass in parallel glass joints, and anodized aluminium corner profile in corner glass joints including the cost of 12mm thick toughened and heat soaked glass.

od131437/2020_2021 : Partition above false ceiling level, closing by Calcium silicate board with frame work.<br>Providing and fixing Partition above the false ceiling level using Aluminium box frames of size 50mmx25mmx1.5mm thickness at 610mmc/c on both directions and to be covered with 9mm thick single layer Calcium silicate board on both sides. The joints are to be finished with jointing compound as per manufacturers specification. The boards shall be fixed with counter sunk stainless steel / fully threaded self tapping screws of suitable dia and length at every 300 mm c/c. Note: The framework shall be anchored/ fixed properly in true RCC ceiling, to get sufficient rigid both side aluminium 'Y' type support.

od174257/2020_2021 : Gypsum partitition<br> 122mm thick GI stud partition which includes double layer of 12.5mm thick Gypsum Board consists of tapered edge & dense Gypsum core further contributes to “Severe Duty Rating” for partition as per BS 5234 Part 2) of size 1220x2440mm is screw fixed to C-stud. 70 x 34 x 36 x 0.5mm C-stud (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513) placed at 610mm c/c in 72 x 32 x 32 x 0.5mm floor and ceiling channel (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513). Floor & Ceiling channel is anchored to the floor & True ceiling using Rawl plug (Anchor Fastener) Ø8x45mm {Material-IS 513 CR1 grade, Zinc coating, Pull Out Load-6.8kN for M30 concrete grade} at 600mm c/c in zigzag manner<br>Floor channel to be wrapped with 70μ Self Adhesive LDPE moisture barrier film to further improve corrosion resistance performance. 12.5mm thick Gypsum Board consists of tapered edge & dense Gypsum core which further contributes to “Severe Duty Rating” for partition as per BS 5234 Part 2) strip of 72 mm width is placed between ceiling channel and RCC ceiling slab when deflection is more than 10mm & fire rating is more than 30min. A Noggin channel of size 70 x 40 x 40 x 0.5mm (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513) has to be provided at the horizontal joints of the two boards<br>Gypsum board to be screw fixed with Drywall screws of 25mm at minimum spacing of 300mm at center and 150mm at periphery. 50mm Glass wool slab of density 20kg/m³ shall be placed in metal framework. Glass wool holding clip should be used to hold Glass wool slab in its position. Finally, square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Gypsum Jointing compound, (Conforms to ASTM C475) and Joint Paper tape. The junction of the partition with masonry & all penetration through the partition has to be treated with Hilti/Pyroplex fire and acoustic sealant. All the above mentioned technical parameters will be approved based on third party certification from the manufacturer<br>single layer of gypsum at above falseceling level

od174258/2020_2021 : Gypsum partitition<br> 122mm thick GI stud partition which includes double layer of 12.5mm thick Gypsum Board consists of tapered edge & dense Gypsum core further contributes to “Severe Duty Rating” for partition as per BS 5234 Part 2) of size 1220x2440mm is screw fixed to C-stud. 70 x 34 x 36 x 0.5mm C-stud (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513) placed at 610mm c/c in 72 x 32 x 32 x 0.5mm floor and ceiling channel (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513). Floor & Ceiling channel is anchored to the floor & True ceiling using Rawl plug (Anchor Fastener) Ø8x45mm {Material-IS 513 CR1 grade, Zinc coating, Pull Out Load-6.8kN for M30 concrete grade} at 600mm c/c in zigzag manner<br>Floor channel to be wrapped with 70μ Self Adhesive LDPE moisture barrier film to further improve corrosion resistance performance. 12.5mm thick Gypsum Board consists of tapered edge & dense Gypsum core which further contributes to “Severe Duty Rating” for partition as per BS 5234 Part 2) strip of 72 mm width is placed between ceiling channel and RCC ceiling slab when deflection is more than 10mm & fire rating is more than 30min. A Noggin channel of size 70 x 40 x 40 x 0.5mm (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513) has to be provided at the horizontal joints of the two boards<br>Gypsum board to be screw fixed with Drywall screws of 25mm at minimum spacing of 300mm at center and 150mm at periphery. 50mm Glass wool slab of density 20kg/m³ shall be placed in metal framework. Glass wool holding clip should be used to hold Glass wool slab in its position. Finally, square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Gypsum Jointing compound, (Conforms to ASTM C475) and Joint Paper tape. The junction of the partition with masonry & all penetration through the partition has to be treated with Hilti/Pyroplex fire and acoustic sealant. All the above mentioned technical parameters will be approved based on third party certification from the manufacturer.<br> 1.80 m high partition with floor and wall supports only

od174259/2020_2021 : Gypsum partitition<br> 122mm thick GI stud partition which includes double layer of 12.5mm thick Gypsum Board consists of tapered edge & dense Gypsum core further contributes to “Severe Duty Rating” for partition as per BS 5234 Part 2) of size 1220x2440mm is screw fixed to C-stud. 70 x 34 x 36 x 0.5mm C-stud (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513) placed at 610mm c/c in 72 x 32 x 32 x 0.5mm floor and ceiling channel (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513). Floor & Ceiling channel is anchored to the floor & True ceiling using Rawl plug (Anchor Fastener) Ø8x45mm {Material-IS 513 CR1 grade, Zinc coating, Pull Out Load-6.8kN for M30 concrete grade} at 600mm c/c in zigzag manner<br>Floor channel to be wrapped with 70μ Self Adhesive LDPE moisture barrier film to further improve corrosion resistance performance. 12.5mm thick Gypsum Board consists of tapered edge & dense Gypsum core which further contributes to “Severe Duty Rating” for partition as per BS 5234 Part 2) strip of 72 mm width is placed between ceiling channel and RCC ceiling slab when deflection is more than 10mm & fire rating is more than 30min. A Noggin channel of size 70 x 40 x 40 x 0.5mm (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513) has to be provided at the horizontal joints of the two boards<br>Gypsum board to be screw fixed with Drywall screws of 25mm at minimum spacing of 300mm at center and 150mm at periphery. 50mm Glass wool slab of density 20kg/m³ shall be placed in metal framework. Glass wool holding clip should be used to hold Glass wool slab in its position. Finally, square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Gypsum Jointing compound, (Conforms to ASTM C475) and Joint Paper tape. The junction of the partition with masonry & all penetration through the partition has to be treated with Hilti/Pyroplex fire and acoustic sealant. All the above mentioned technical parameters will be approved based on third party certification from the manufacturer

Miscellaneous

od131771/2020_2021 : ROLLER BLINDS<br>Roller shades-Chain Driven System<br>Providing and fixing of Hunter Douglas Roller shades-HD 38 system (Regular) / PHIFER / VISTA<br>Chain System Drive Unit shall be of molded plastic with steel rectangular support pin and ins erted into the tube end. It shall be driven by a ball chain pulley with ball chain and can be positioned at right hand or left hand side of the shade. The shade, when lowering or raising, shall be automatically locked in position upon release of the ball chain by means of a built in friction lock.<br>Chain System Idler Plug shall be of moulded plastic with a steel location pin. The plug shall be ins erted into the tube end.<br>Chain System Support Brackets shall be of moulded plastic and used in right hand or left hand positions differentiated by the acceptance of the rectangular drive unit support or the round idler plug pin.<br>Roller Tubes shall be roll-formed and lock-seamed steel of 0.43mm thickness suitably protected against corrosion and shall incorporate a keyway integral with the tube to accommodate the spline. The outside diameter of the roller tube shall be 25mm, 28mm or 38mm depending upon the application.<br>Bottom Rail shall be a stiffening element ins erted into a bottom rod pocket with the ability to pull down the shade at the centre. The material may be timber, or P.V.C. covered steel tube.<br>Cord Pull shall be provided, and screwed to the bottom lath to aid in the operation of the shade.<br>Ball Chain shall be 2mm diameter cord with 4.5mm diameter acetal balls moulded co-axially to it on 11.8mm pitch to form a endless ball chain. It is used for raising or lowering action of the shades.<br>Basketweave white sand 5% (Optima sunscreen / Phifer / Vista)

od131773/2020_2021 : Providing and fixing soft board panel of specified sizes having 12mm thick soft board with a 8mm thick BWR plywood backing and softboard covered with fabric of approved make and shade of premium quality and cost of fabric not less than Rs.300/1meter ht.1200mm). The board shall have a teakwood / cedar / beech / matching wooden beading, lipping around. The board shall be fixed with hook on system on the existing panelling or wall prepared surface with necessary hardware fittings etc. complete. All wood works shall have sealer polish as directed. Rate quoted shall be for the complete finished work including all the materials and labour mentioned above.

od131774/2020_2021 : Providing and fixing of Anodized aluminium extruded skirting of 1mm Thick polished finish as per approved make or equivalent make to a height of 100mm. Rate shall be inclusive of fixing as per manufacturer specification and the fixing screws should not be visible.

od131775/2020_2021 : Providing and fixing of 6mm thick lacquered glass of approved colour and make along with 12mm thick BWR plywood backing panel screw fixed over the existing partition, or wall panelling frame work or wall surfaces and using required area 3M make double side adhesive tapes. The rate shall be inclusive of necessary hardware, adhesive taps and wastage etc; complete.

od131776/2020_2021 : Providing and fixing white matt finish white mark writing board of enamelled sheet steel front, GI back over approved inner core, of specified size black or chocolate colour wooden beading with polish finish to form the screen including the necessary accessories such as magnetic symbols, magnetic letters, magnetic strips, magnetic eraser, magnetic dry marker 4nos spare felt for eraser, board fixing clips etc. and the board shall be made out of enamelled sheet with backing of AC sheet to suitable thickness etc. complete and all as per manufacturer's specification and as directed by the Employer / Architect. Rate shall inclusive of making and fixing wooden ledge for full length of the board for keeping marker pen, eraser etc. Rate quoted shall be for the complete finished work including ledgeboard to keep accesories , and all materials and labour mentioned above.

od131777/2020_2021 : Providing and fixing of 3M frosted film of approved color as per required pattern and shape and as directed. The vendor shall submit required warranty certificates from the manufacture. (Basic cost Rs.1200/Sqm)

od131778/2020_2021 : Providing and applying Texture paint of approved colour on existing gyspum surface from asian paints/ nerolac or oikos as per the directions of Engineer-in-charge. basic rate of texture Rs 500/sqm

od131779/2020_2021 : Wall paper : SUPPLY & installation of wall paper on existing wall/partition, after punny, painting with primer coat and curing of the surface to ensure propoer levelling and surface treatment prior to fixing of wall paper., inclusive of wastage. Basic cost Rs.110/sft

od131780/2020_2021 : Green wall system: Designing, providing and fixing the stainless steel cable at 300mm c/c on the directions and as per drawing also the system comprising of stainless steel supporting brackets, fasteners as indicated in the drawing. The fastening materials like wire ropes, Anchors, Nuts, Bolts, Rivets, washers, clamps, straps etc shall be of stainless steel 316 grade and corrosion resistant of approved make as per Architects / Consultants Specification. Rate shall include the cost of Designing the system including Green wall & related assembly , Handling, Shifting, hoisting & Installing the system with all required hardware's and accessories as per design.

od131781/2020_2021 : Providing dadoing with best quality approved make Slate tiles of approved size set in C.M.1:3 and white cement slurry with approved joint filler grout compound, all as per manufacturer's specification, at all levels and as directed. Rate shall include for preparation of plastered surface, smooth joint, cleaning etc. complete and as directed. (Basic cost is at Rs.3000/1Sqmt)

od131782/2020_2021 : Providing dadoing with best quality approved make glazed mosaic tiles of 20mmx20mmx3mm thick size set in C.M.1:3 and white cement slurry with approved joint filler grout compound, all as per manufacturer's specification, at all levels and as directed. Rate shall include for preparation of plastered surface, smooth joint, cleaning etc. complete and as directed. (Basic cost is at Rs.3000/1Sqmt)

od131783/2020_2021 : EMULSION PAINT<br>Providing two coats of first quality Acrylic emulsion paint of approved make and colour over a priming coat of white colour paint or any primer specified by the manufacturer including preparation of surface by thorough cleaning and wetting before painting and all as per manufacturer's specifications and as directed.

od131784/2020_2021 : Providing and fixing wall cladding Kalinga wall panels Engineered Marble Slabs / Engineered terrazo slabs as per approved shade with all necessary base panel work with aluminum wall supports and 12 mm thick BWR ply as per manufacturer's Specification and as directed. The Rate includes installation cost with adhesive.Basic rate Rs.300/Sqm

od131785/2020_2021 : Providing and finishing the partition and wall surfaces with Veneitian plaster or polished plaster or texture paint including stencil painting work of approved make as per Architects design and manufacturer specifications. Base rate is Rs.2500 per 1sqm

od131786/2020_2021 : Supplying and fixing Planter box using 18mm thick BWR ply with necessary hardwares and finished with paint. 450 mm wide and 300 mm depth

od131787/2020_2021 : Providing and fixing Pelmet made to shape and sizes as given in below, but in general it shall be made out of 19mm thick BWR plywood and lined with 1.5mm thick lamination of approved colour as directed. Rate shall be inclusive of necessary fixing accessories like hangers rods/ anchors, sunken screws etc; complete including the cost of Hilti make Anchor fastners.<br>150mmx150mm size

od131788/2020_2021 : Providing and Fixing Wall cladding with 12mm thick ply with all supports and top finished with veneer finish and polish

od131791/2020_2021 : Providing and fixing Logo signage with 3D Acrylic letters, finished with PU coat of approved colour fixing over the existing wall surfaces using approved batch fitting. (Size as per standard 1650mm x 250mm height approximately)

od131792/2020_2021 : Design, supply, fabrication and fixing of wall / door mounted type signages comprising of anodized, imported extruded aluminium profile with ABS endcaps with single side vinyl graphics as per design and approval. The Dimension of the signage system shall be 80mmx400mm. The rate shall be include the cost of double side adhesive taps, screws and fixing accessories as required.

od131793/2020_2021 : Supplying and fixing ONYX wall cladding with necessary back supports as per manufacturer specifications

od131794/2020_2021 : Providing and fixing of 8mm thick lacquared glass write on board backing with 12mm thick BWR ply both side finished with two coats enamel paint of approved shade over a coat of primer. Edges covered with 50mmx50mm teak wood decorative beading finished with melamine matt polish of required level. The rate shall be inclusive hardware, lead and lift etc.

od131795/2020_2021 : Supplying and fixing Pull down Projector screen with remote operation of approved make

od131796/2020_2021 : Providing and fixing approved colour 3M Normad entry way system/approved equivalent make Aqua medium duty mats for Office entrances with Unique dual fiber construction, for removal of moisture and fine sand with absorption technology. Loop piled featuring tufted construction with two different synthetic fibres namely polypropylene and nylon combined to maximize dirt removal, water pickup and holding capacity. Suitable for traffic of upto 6 lakh people per year. The size of the mat is 1500mmx900mm.

od131797/2020_2021 : Providing and fixing signage for "Emergency route map" using 8mm thick clear Acrylic base plate of and the corners of the base plate shall be rounded off and edge polished. The text and the graph shall be with "3M" make vinyl film and to be fixed on the RCC / masonary surfaces using SS studs projected from wall by 12mm. The total signage size shall be 400mmx400mm.

od131803/2020_2021 : Providing and Fixing Ecophon WALL PANEL A Akutex FT 1200 x 2700 mm with 40 mm natural square edge ,demountable panels with standard approved fabric wrapped around in concealed system with grippers, option of Daily dusting, vacuum cleaning & weekly wet wiping. Panel is manufactured from high density glass wool utilizing the 3 RD technology<br>Tiles classified under sound absorption class A with "alpha w " value of 1 at minimum 50mm o.d.s. Classification acc to EN ISO 11654, & single value ratings for NRC value 0.9 according to ASTM C 423. Articulation class 230 as per ASTM E1111, ASTM E1110. Panels withstand a permanent ambient RH up to 95% at 30*C & RH upto 75% at 30*C without sagging, warping or delaminating (EN13964). Thermal resistance (Lamda value - 0,035-0,04 W/mK) <br>Certified by the Indoor Climate labelling, emission class M1 for building materials & recommended by Swedish Asthma & Allergy Association. Product Certified under GRIHA Council of India for Green ratings. Fully recyclable.The glass wool core of the tiles should be tested and classified as non combustible according to prEN ISO 1182 with reaction to fire classification class A2 s1 d0 according to EN 13501  - 1 - European Standard.

od131804/2020_2021 : Providing and Fixing Teak wood board size 150mm wide*20mm thick as shown in drawing to complete

od131805/2020_2021 : Proving and fixing of Stage flooring -Synthetic polyfibre 50mm thick at Theatre area as shown in drawing to complete(synth PF 10MM*50MM).

od131806/2020_2021 : Supply and installation of Sensus/ Approved acoustic panels to a thickness not less than 12mm fixed over the existing partitions/ walls with adhesives. Spacing between the panels to be as per manufacturer's specification. Rate shall be inclusive of adhesives, brackets, wastages, all accessories and scaffolding at all heights.<br>Basic Price - Rs 200/ Sft.

od131815/2020_2021 : Supplying and fixing Rock wool 75mm thick insulation of 48kg/cum with GI frame covered the fabric

od131818/2020_2021 : Providing and fixing wall cladding Form and Surfaces bonded with light panel as shown in drawing to complete

od131821/2020_2021 : Providing and fixing WALL panelling as shown in drawing no. Wooden slots fixed to the wall 100 x 50 x50 mm at 600 mm c/c with GI Channel 50 mm height fixed to the wooden slots covered fabric wrapped glass wool panels of size 600 / 1200 x 1200 x 25 mm thick of approved shade including forming pattern and details as in drawing with necessary hardwares. Rate shall include for forming a panelling to any shape including circular profile etc.Rate include 75mm thick rockwool insulation with 48kg/cum

od131822/2020_2021 : Supply and fixing of Kerradeco, wall cladding, of panel sizes of 295mmx 2700mm x 9mm, resistant to moisture, water and impact. The panel must be durable and impact resistant as per EN 13245-1 and scratch resistant as per EN 438-2 p.25. The panel must be tested as per EN 13501-1 and BS 476 part 7 and must contribute towards sound insulation as per EN ISO 140-4 & EN ISO 717-1 of the room. The panel should be Safe to contact food as per EN 1186-1 EN 1186-3 EN 1186-14 and must not contain lead and tin. It hsould not emit harmful substances as per ISO 16000.<br><br>The panels will be interlocked and fixed with McCoy Soudal Fix All high tack bonding adhesive seal to ensure proper adhesion.<br><br>Should be non toxic substances, and made made of recycledmaterials and 100% suitable for recycling.<br><br>Suitable finishing trims to be used as required. 10 Years of Warranty for Colour & Finish .

od135458/2020_2021 : Providing and fixing wall cladding Form and Surfaces bonded with metal slats as shown in drawing to complete

od135522/2020_2021 : Providing and fixing Rockwool Wall Insulation as shown in drawing no. GI sections 50 mm x 48 mm x 1.6 mm thick at 600 mm c/c covered with 2 layers of 75 mm thick insulation 1200 GSM SWK Snow white including Black Colour Fire retardant fabric with forming pattern and details as in drawing with necessary hardwares. Rate shall include for forming a panelling to any shape including circular profile etc.<br>

15.3 : Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

15.7.4 : Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

od175705/2020_2021 : STEEL SUPPORT FOR WALL PANEL<br>Providing and fixing in position Hot rolled structural steel Members / Sections at all levels and to any shape & profile, if specifically ordered as & when required by the Employer/PMC/Architect and to be executed on prior approval (In general the structural Supports called for as part of the Schedule of quantities item elsewhere in the Schedule of quantities will not be considered in this item) and the structural support may be called for in a special case for cladding on the ceiling / soffit etc. In general, Structural steel consists of MS joists, channels, beams, angles, purlins, runners, pipes (hollow / solid – square / rectangular / circular) UC, UB section, in sert plates, flats and sag rods with necessary sleeves, bolts and nuts, gratings including cutting, straightening, welding as per standards for connections including consumables, anchoring the structural members in to the RCC/Masonry wall with suitable anchor fastener of Hilti / Mungo / Fischer make etc complete.<br>"Rate shall include Surface preparation of all MS members by Sand blasting to SA 21/2 grade and painted with anti corrosive, low VOC PU paint (metallic finish) with compatible primer to a minimum film thickness of 75 microns and 2 coats of low VOC PU paint of Akzonoble make and total dry film thickness 225 microns. (Only related to Facade works and no base frame or support structure included) Note: In general the structural steel members called for as part of the Schedule of quantities item elsewhere in the Schedule of quantities will not be considered in this item."

od279211/2020_2021 : Providing and fixing Steel column at regular interval cladded top with steel pergola & Multiwall polycarbonate sheet canopy above.

od279199/2020_2021 : Providing and Fixing of Multi cell Polycarbonate Panels 16 mm thick with 5 cells - 6 walls structure over MS Supporting structures. Panel Width shall be 900 mm to ensure best performance for wind uplift. The panels shall be uniform in color with an integral Multi-Cell core. In a cross section, the core shall be constructed of Microcell of max 4.5mm x 4.5mm. Panels having Vertical Standing Seam 15mm at both sides; snap-on connector to interlock the panels shall have a grip-lock 2 tooth locking mechanism to ensure maximum uplift capability. Panels shall be fixed on Purlins with special Expansion fastener, polycarbonate U connectors. Panels shall be manufactured with approved quality assurance as per ISO 9001 & ISO 14001 and manufactures should have successful project reference having minimum 1500 sq mtr in Indian sub-continent at least for 10 years old.<br>

od337861/2020_2021 : Providing and fixing Tensile steel Roof including all necessary structural steel support etc. complete, A. Design & Materials:<br>Design, Supply, Fabricate & Install Tensile roof structure using Ferrari make Fabric of product code no. 1002 Floutop T2 at all levels and elevation as per drawing with the approved Profile. In General, the Fabric shall have thickness not less than 0.78 mm with tensile strength 480/450 Lbs shall satisfy ASTM - D 751,Tear resistance of 105/100 Lbs/in shall satisfy ASTM - D 751, Weight - 1050g/sqm and in accordance with EN ISO 2286 - 2 and the Fabric shall made out of PES HT 1100Dtex yarn with flame Retardancy to meet Euro Class B-s2.d0/EN 1350-1 and the Surface treatment shall be Floutop T2 (High concentration PVDF) having coating thickness not less than 350 µ and back side treatment shall be weld able PVDF (for a better resistance to pollution of the back side of the fabric) with a minimum Manufacturer warranty of 20 years. Rate Shall include patterning, form finding, cutting, welding & installation of fabric at site, primary & secondary steel structures in MS of TATA / JINDAL or Equivalent make with YST 310 grade as minimum including fabrication and erection of structural elements duly painted with two coats of Pu based Metallic shade paint of approved shade over one coat of epoxy primer to a total DFT of 230 Microns of Akzo noble or Jotun make. Rate to include necessary tensioning hardwares for fabric in SS accessories inclusive of Wire ropes (GI hot dip galvanized cables), Swage ends & membrane plates etc as per drawings and Manufacturers Specification. The complete roofing System to be designed to with stand design wind pressure of 250Kg/Sqm confirming to IS 875 part 3 and other load parameters as per IS or relevant international code etc<br>B. General Guideline:Rate to include necessary tensioning hardwares for fabric in SS fastening inclusive of Wire ropes (GI hot dip galvanized cables), Swage ends & membrane plates etc as per drawings and Manufacturers Specification, all related accessories, Bolts, Nuts, Washers, Spring washers, Welding, Gusset plates, base plates, etc., Primer, epoxy coating, PU painting etc and necessary wastage, lead, lift etc. Electricity, water, Staging, scaffolding, platform, ladders, chain pulley blocks, ropes, Transport Charges, Loading and Unloading charges, Storage of materials at site, Preparation of Temporary Storage arrangement, protection of materials (Free Space will be provided for storage), etc. required for erection work including cranes of appropriate capacity, if needed.Preparation of shop drawings by the Specilized vendor for approval of the Client / PMC / Architect / Consultant including giving four sets of approved shop drawings for their record. Necessary related civil works shall be executed in-coordination with Civil agency based on the technical drawings submitted by Tensile Vendor and approved. Design and install all Fasteners, anchor rod / bolts & nuts shall be SS 316 grade and all materials & labour involved in this scope of work. All the member joints shall be welded with suitable thickness and type as design and the welded areas shall be finished with spray / brush applied galvanizing coating if G.I structural members proposed. Bidders shall be considered the connections between Membrane & Structure, seams on the Membrane, tensioning & clamping of the Membrane shall be as per design criteria.Rate shall include the cost for Design, Supply, Fabricate & Install Tensile roof structure using Tensile Fabric, Surface treatment with Floutop® T2 (High concentration PVDF) having coating thickness not less than 240 µ and back side treatment shall be weldable PVDF (for a better resistance to pollution of the back side of the fabric), also rate shall include the cost for Desiging, providing, fabricating and fixing of PU painted / G.I Structural steel works etc complete.C. Mode of Measurement: Fabric Coverage area as installed from end to end shall be measured. No Folds and trims will be considered for payment. i.e Horizontal Plan area shall be considered for payment in Square meter (Sqm).

od176613/2021_2022 : Providing and fixing Pantry counter to a minimum width of 600mm and to a specified height as shown in drawing but in general, the counter top shall be made of 19mm thick Marin ply topped with 12mm Corian dupont sheet of approved colour. The rate shall include for the providing storage unit below with openable shutters. The top, bottom and intermediate shelf having 19 mm thick Marin plywood with 1.5mm thick (texure shade) laminate. The openable shutter shall be made of Aluminium frames of Hatich make with frosted 6mm thick glass including hardwares like handles, hinges, ball catches etc.complete.Pantry counter shall have glass shelves with ply shutter for the sink area with window droope chute. Rate shall be inclusive of providing provision to fix SS sink drain board, garbo drain. basic cost of laminate Rs.400/Sqm and the corian dupont sheet basic cost is Rs.6500/Sqm.

od177694/2021_2022 : Providing and fixing of 6mm thick bevelled edge mirror of height 1500mm backing with 12mm thick BWR ply fixing with stainless steel studs.

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

6.4.1 : Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:Cement mortar 1:4 ( 1 cement : 4 coarse sand)

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

13.7.2 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:4 ( 1 cement : 4 fine sand)

13.26 : Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

od178185/2021_2022 : Provding & applying PU polish for Teak Wood Door Frames with necessary application of Filler n sealer all complete.

od178314/2021_2022 : Supplying,installing, testing and commissioning of White color Oval Wash basin size 550x410mm(below counter ) type with CP Pillar tap, 32mm dia CP waste coupling, 32mm dia CP bottle trap with extension pipe, pair of stainless steel bolts,with bracket (MS /CI ) to support to the basin, 15mm CP angle valve with CP inlet connection tube , CP wall flange, including necessary brakets etc complete. Works including cutting and making good the walls /floor wherever required, etc., complete.

od178315/2021_2022 : Providing & fixing sheer blinds of approved pattern & make as per specifcation

18.51.1 : Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

18.8.1 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.15 mm nominal outer dia pipes

18.8.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal outer dia pipes

18.8.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal outer dia pipes

18.8.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.32 mm nominal outer dia pipes

od178750/2021_2022 : Providing, fixing and testing UPVC Class-3 pressure rating 6 kg /sqcm pipe of approved Make for underground drainage and sewerage systems - Confirming to IS 4985:2000 and speciels such as such as coupler, elbow, bends and Tee,etc This includes jointing of pipes &fittings with solvent cement and cost of cutting chases and making good the same include testing of joints for suspended lines and work in below ground. Woks includes necessary scaffolding,cutting and making good the walls wherever required ,complete as per direction of Engineer in charge. 50mm dia

od178751/2021_2022 : Providing, fixing and testing UPVC Class-3 pressure rating 6 kg /sqcm pipe of approved Make for underground drainage and sewerage systems - Confirming to IS 4985:2000 and speciels such as such as coupler, elbow, bends and Tee,etc This includes jointing of pipes &fittings with solvent cement and cost of cutting chases and making good the same include testing of joints for suspended lines and work in below ground. Woks includes necessary scaffolding,cutting and making good the walls wherever required ,complete as per direction of Engineer in charge.a).40mm dia

od179061/2021_2022 : Providing and fixing of Backdr op at reception, in general it shall be made of required 18mm plywood of Century / Greenply / Kitply make backing to receive the 3 Form / Onyx of cladding with different pattern and creating the niche of approved shade/colour all as per detail dwg on the existing partition (Gypsum board/plywood). The rate shall be inclusive of necessary adhesive, hardware, wastage, scaffolding, and stiffener at around the edges etc. complete and all as directed.

od179195/2021_2022 : Providing and fixing of Anodized or Powder coated Global make aluminium fixed windows by using 63.50 x 38.1 x 2mm thick box sections for outer frame and mullions, with glazing clips and EPDM Gaskets including 5mm thick clear float glass complete

od179196/2021_2022 : Providing and fixing in position of Aluminium sliding window using suitable sections for three track system, Interlocking frame with 5mm thick float glass with all accessories and finished the surface neat etc complete as directed by Engineer In charge

8.31 : Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

od179212/2021_2022 : Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 710 x 450 x 330mm including sensor flush valve having pre & post flushing with water ( 250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.Works including cutting and making good the walls /floor wherever required, etc., complete. <br>

od179213/2021_2022 : Providing and fixing liquid soap container of approved make near wash basins with necessaryfixing screws and clamps etc., complete.

od179214/2021_2022 : Supplying , fixing in position and testing C.P. health faucet wall hook 1.2 metre long flexible tube, 15mm CP Angle valve with connection tube model no: CON-053-KN with wall flange all complete, Works including cutting and making good the walls /floor wherever required, etc., complete.

od179215/2021_2022 : Supplying and fixing cp Double Coat hook fixing with necessary screws etc., complete.

od179216/2021_2022 : Supplying, Installing, testing and commissioning of White color Floor Mounted European water closet with inbuilt low level PVC flushing cistern and Wash Basin for Physically Challenged Persons with necessary Grab Rails, hinged rails for support , pan connecter bend,checknut, stopcock etc., colour solid seat and cover with polythene buffer and flap, CP flanges, CP bolts and nuts, bracket with nuts and bolts wall flanges etc.,complete, Wash Basin shall include 15mm dia CP liver operated pillar Cock with waste coupling, 32mm dia CP bottle trap with extension pipe,supporting bracket with necessary steel to support basin 1 No.15mm CP angle valve with 450mm long CP connection pipe and CP wall flanges all of approved make etc., complete. Works including cutting and making good the walls /floor wherever required, etc., complete.

od179217/2021_2022 : Providing and fixing White Color European Water Closet - Wall mounted type with integral low level flushing cistern(Dual flushing type-3 liter/ 6 liter (adjustable to 4 liter/ 2.5 liters)- 'P' trap including following accessories: solid seat and cover with rubber buffers and flap, brackets, brass screws with washer, 15mm CP Angle valve with connection tube,CP wall flange, pan connector, CI chair bracket,all hardware items like wallbrackets bolts washers & screws & brackets to be painted with two coats of enamel paint of approved shade over a coat of primer and necessary screws,etc.complete. Works including cutting and making good the walls /floor wherever required, etc., complete.

17.34.1 : Providing and fixing toilet paper holder:C.P. brass

18.7.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall20 mm nominal outer dia pipes

18.7.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall25 mm nominal outer dia pipes

18.7.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall32 mm nominal outer dia pipes

18.7.5 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall40 mm nominal outer dia pipes

18.7.6 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall50 mm nominal outer dia pipes

od179414/2021_2022 : Supplying and fixing of 25mm dia Air release valve etc. complete

od179415/2021_2022 : Providing and fixing ball valve (brass) of approved qualityetc. Complete d).50 mm nominal bore

od179416/2021_2022 : Providing and fixing ball valve (brass) of approved qualityetc. Complete b).40 mm nominal bore

od179417/2021_2022 : Providing and fixing ball valve (brass) of approved qualityetc. Complete b).32 mm nominal bore

od179418/2021_2022 : Providing and fixing ball valve (brass) of approved qualityetc. Complete a).25 mm nominal bore

od179425/2021_2022 : Supplying, fixing and testing of UPVC urinal trap with CP anti foul drainer square cockroach trap, 150 mm nominal size square 100mm diameter of the inner hinged round grating various inlet from 40 dia to 110 dia and various outlet from 75 dia to 100 dia with the extension pipe, boss tee connections, fixed in sunken floors /Suspended support with ceiling level etc., complete. Works including cutting and making good the walls /floor wherever required, etc., complete.

od179426/2021_2022 : Supplying,fixing and testing of UPVC floor clean out used in sunken floors,75 or 110mm dia with extension pipes,specils such as 45 degrre bend , tee ,CP tile grating and end cap (clean out plug ).the cap arrangements with female thread fix with the upvc clean out plug in male thread with gascet and s.s screws etc. complete. Works including cutting and making good the walls /floor wherever required, etc., complete.

od179427/2021_2022 : Supplying,fixing and testing of UPVC floor trap with cockroach trap and CP grating 150 mm nominal size square 100mm diameter of the inner hinged round grating various inlet from 40 dia to 110 dia and various outlet from 75 dia to 100 dia with the extension pipe, boss tee connections, fixed in sunken floors /Suspended support with ceiling level etc., complete.

od179428/2021_2022 : Providing, fixing and testing UPVC SWR- B Class pipe confirming to IS 13592-1992. and fittings confirming to IS 14735-1999, such as such as coupler, elbow, bends, Tee, Y, vent cowl etc for Soil, Waste and rain water pipe works in shaft and suspended in ceiling., laid in ground( from shaft to Inspection chamber and Gully chamber), etc., using rubber ring joints(rubber ring confirming to IS 15382) for shafts lines and solvent cement joints for suspended lines and work in below ground. Woks includes necessary scaffolding,cutting and making good the walls wherever required all complete as directed by the Engineer-in-Charge. a).110 mm dia

od179429/2021_2022 : Providing, fixing and testing UPVC SWR- B Class pipe confirming to IS 13592-1992. and fittings confirming to IS 14735-1999, such as such as coupler, elbow, bends, Tee, Y, vent cowl etc for Soil, Waste and rain water pipe works in shaft and suspended in ceiling., laid in ground( from shaft to Inspection chamber and Gully chamber), etc., using rubber ring joints(rubber ring confirming to IS 15382) for shafts lines and solvent cement joints for suspended lines and work in below ground. Woks includes necessary scaffolding,cutting and making good the walls wherever required all complete as directed by the Engineer-in-Charge. a).75mm dia

od179457/2021_2022 : Providing and laying autoclaved aerated cement blocks masonry with 150mm/<br>230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V<br>level with RCC band at sill level and lintel level with approved block laying polymer<br>modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The<br>payment of RCC band and reinforcement shall be made for seperately).

od179460/2021_2022 : Providing and laying in position ready mixed concrete manufactured in fully automatic batching plant and transported to site of work in transit mixer having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Providing M-40 grade concrete BMC/RMC.(Note :Minimum Cement content considered in M- 40 is @ 360 kg/cum) quote shall contian additional cement used for arriving the required strength

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

od179471/2021_2022 : Demolishing AAC/ Solid Block work in cement mortor manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

9.1.1 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

9.53 : Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.85.3 : Applying priming coats with primer of approved brand and manufacture, having low VOC ( Volatile Organic Compound) content.With water thinnable cement primer on walls surface having VOC content less than 50 grams / litre

od179473/2021_2022 : Providing and fixing chlorinated Polyvinyl chloride (CPVC) pipes, fittings up to 50 mm dia SDR 11 ASTM CTS and above 50mm dia CPVC schedule 80 , having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting including fixing the pipe with clamps at 1.00m spacing. this includes jointing of pipes &fittings with one step CPVC solvent cement and cost of cutting chases and making good the same include testing of joints complete as per direction of Engineer in charge.g).100 mm nominal outer dia pipes

od179474/2021_2022 : Providing and fixing chlorinated Polyvinyl chloride (CPVC) pipes, fittings up to 50 mm dia SDR 11 ASTM CTS and above 50mm dia CPVC schedule 80 , having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting including fixing the pipe with clamps at 1.00m spacing. this includes jointing of pipes &fittings with one step CPVC solvent cement and cost of cutting chases and making good the same include testing of joints complete as per direction of Engineer in charge.f).80 mm nominal outer dia pipes

od179475/2021_2022 : Providing and fixing chlorinated Polyvinyl chloride (CPVC) pipes, fittings up to 50 mm dia SDR 11 ASTM CTS and above 50mm dia CPVC schedule 80 , having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting including fixing the pipe with clamps at 1.00m spacing. this includes jointing of pipes &fittings with one step CPVC solvent cement and cost of cutting chases and making good the same include testing of joints complete as per direction of Engineer in charge.e).62.5 mm nominal outer dia pipes

od179590/2021_2022 : Making Core Cutting in slabs / beams / retaining walls and any other R.C members to any dia & depth by using 'HILTI' make diamond drilling machine with tolerance for any type of inse rts, anchor fasteners etc. Rate shall include for sealing the gaps between RC surface and inser ts with fire retardent grouting material as per manufactures specification ,all charge, preparation of surface, cutting of reinforcement, cleaning the surface, staging, scaffolding with necessary tools and equipments water and power, removal of debris from the site, staging scaffolding etc complete, as directed. 110 to 160 mm dia pipe to the following depth:250mm depth

od179591/2021_2022 : Making Core Cutting in slabs / beams / retaining walls and any other R.C members to any dia & depth by using 'HILTI' make diamond drilling machine with tolerance for any type of inse rts, anchor fasteners etc. Rate shall include for sealing the gaps between RC surface and inser ts with fire retardent grouting material as per manufactures specification ,all charge, preparation of surface, cutting of reinforcement, cleaning the surface, staging, scaffolding with necessary tools and equipments water and power, removal of debris from the site, staging scaffolding etc complete, as directed. 110 to 160 mm dia pipe to the following depth:200 mm Depth

od179592/2021_2022 : Making Core Cutting in slabs / beams / retaining walls and any other R.C members to any dia & depth by using 'HILTI' make diamond drilling machine with tolerance for any type of inser ts, anchor fasteners etc. Rate shall include for sealing the gaps between RC surface and inser ts with fire retardent grouting material as per manufactures specification ,all charge, preparation of surface, cutting of reinforcement, cleaning the surface, staging, scaffolding with necessary tools and equipments water and power, removal of debris from the site, staging scaffolding etc complete,as directed. 110 to 160 mm dia pipe to the following depth:150 mm Depth

od179593/2021_2022 : Making Core Cutting in slabs / beams / retaining walls and any other R.C members to any dia & depth by using 'HILTI' make diamond drilling machine with tolerance for any type of inser ts, anchor fasteners etc. Rate shall include for sealing the gaps between RC surface and inser ts with fire retardent grouting material as per manufactures specification ,all charge, preparation of surface, cutting of reinforcement, cleaning the surface, staging, scaffolding with necessary tools and equipments water and power, removal of debris from the site, staging scaffolding etc complete, as directed.75 to 110 mm dia pipe to the following depth:300 mm Depth

od179594/2021_2022 : Making Core Cutting in slabs / beams / retaining walls and any other R.C members to any dia & depth by using 'HILTI' make diamond drilling machine with tolerance for any type of inser ts, anchor fasteners etc. Rate shall include for sealing the gaps between RC surface and inser ts with fire retardent grouting material as per manufactures specification ,all charge, preparation of surface, cutting of reinforcement, cleaning the surface, staging, scaffolding with necessary tools and equipments water and power, removal of debris from the site, staging scaffolding etc complete, as directed. -75 to 110 mm dia pipe to the following depth:-250mm Depth

od179595/2021_2022 : Making Core Cutting in slabs / beams / retaining walls and any other R.C members to any dia & depth by using 'HILTI' make diamond drilling machine with tolerance for any type of inser ts, anchor fasteners etc. Rate shall include for sealing the gaps between RC surface and inser ts with fire retardent grouting material as per manufactures specification ,all charge, preparation of surface, cutting of reinforcement, cleaning the surface, staging, scaffolding with necessary tools and equipments water and power, removal of debris from the site, staging scaffolding etc complete, as directed. -75 to 110 mm dia pipe to the following depth:-200mm Depth

od179596/2021_2022 : Making Core Cutting in slabs / beams / retaining walls and any other R.C members to any dia & depth by using 'HILTI' make diamond drilling machine with tolerance for any type of inser ts, anchor fasteners etc. Rate shall include for sealing the gaps between RC surface and inser ts with fire retardent grouting material as per manufactures specification ,all charge, preparation of surface, cutting of reinforcement, cleaning the surface, staging, scaffolding with necessary tools and equipments water and power, removal of debris from the site, staging scaffolding etc complete, as directed. -75 to 110 mm dia pipe to the following depth:-150 mm Depth

FLOORING

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

11.41.3 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 800x 800 mm

11.41.4 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 1000x1000 mm

11.46.2 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

11.46.3 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 800 x 800 mm

11.46.4 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 1000x1000 mm

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

od173740/2020_2021 : GRANO FLOOR<br>Providing and laying in panels not more than 20 sqm. in plan granolithic flooring with cement concrete 1:1.5:3 by using coarse graded aggregate of 6 to 12 mm size laid monolithic with floor concrete and finished smooth with power trowel including preparation of concrete surface and form work etc. complete as per Specifications and as directed. Unevenness in floor finish shall not exceed +2mm in one square metre area. Rate to include lead, lift at all levels, pumping, placing, necessary formwork, curing etc., complete <br>Average 50 mm thick.

od173739/2020_2021 : GRANO FLOOR<br>Providing and laying in panels not more than 20 sqm. in plan granolithic flooring with cement concrete 1:1.5:3 by using coarse graded aggregate of 6 to 12 mm size laid monolithic with floor concrete and finished smooth with power trowel including preparation of concrete surface and form work etc. complete as per Specifications and as directed. Unevenness in floor finish shall not exceed +2mm in one square metre area. Rate to include lead, lift at all levels, pumping, placing, necessary formwork, curing etc., complete <br>Average 75 mm thick.

od173839/2020_2021 : CARPET FLOOR<br>Providing and laying of approved make 100% Optimum SD Nylon Tufted, Textured Loop Pile carpet tiles of density more than 6500 oz and20oz/sq.mtr of size 600mmx600mm or any standard size,permanent static control, solution dyed, pile height about 0.118inches with PVC free backing, colorfastness > or =4 after 100hours, moth proof, stain resistant etc. complete, over existing flooring as per Manufacturer's specification. The carpet should be ,class-1 fire rated ,antistatic, moisture barrier, etc. Plank/square (approved shade basic cost Rs.1200/Sqm). The rate shall be include the cost of the supply of carpet necessary adhesive. (Basic Rate Rs.2000 /sqm)

od130680/2020_2021 : Ecofit Flooring (Luxury Vinyl Tile)<br>"Square Foot Ecofit hybrid indoor flooring with stone core<br>It is Waterproof, Termite proof and dimensionally stable when it is laid without expansion joints.<br>It comes with glue less locking system.<br>Scrath resistance, Peel resistance, Slip resistance<br>Class 34, very heavy commercial. Thickness: 4mm, Plank : 4x181x1220mm, Tile : 610x305x4mm<br>(Basic Rate of Tile Rs. 2200 /sqm)<br>

od261397/2020_2021 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.<br>Size of Tile 600x1200 mm

od273955/2020_2021 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.<br>Size of Tile 600x1200 mm

od171998/2021_2022 : Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

11.54.1 : Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of: a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on the G.I. Base plate of size 100mmx100mmx3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5mm welded with GI fully threaded stud 16 mm outer diameter with two GI check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80 mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge. c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Guages: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with light weight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm. The panel is to withstand a Concentrated Load of 363 Kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50 kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product.300 mm Finished Floor Height (FFH).

11.54.2 : Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of: a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on the G.I. Base plate of size 100mmx100mmx3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5mm welded with GI fully threaded stud 16 mm outer diameter with two GI check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80 mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge. c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Guages: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with light weight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm. The panel is to withstand a Concentrated Load of 363 Kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50 kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product.450 mm Finished Floor Height (FFH).

16.89 : Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi models location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

11.48.2 : Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm

11.48.3 : Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 800x800mm

11.48.4 : Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 1000x1000 mm

11.50 : Deduct for not grouting the joints with white cement and matching pigment in the items of fixing of vitrified tiles

od178930/2021_2022 : Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.<br>Size of Tile 600x1200 mm

FALSE CEILING WORKS

12.45.2 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum fire resistant board conforming to IS; 2095-Part I

12.45.4 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:Fully Perforated Gypusm Plaster Board of size 1200 x 2400 x 12.5 mm having approx. 15% perforated area with perforation size and pattern as approved by the Engineer - in- charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60.

od229232/2020_2021 : Providing and fixing in true horizontal level false ceiling of silhouette grid system with 15mm white flanges incorporating a 6mm central reveal in white / black colour of approved make using hot dipped galvanized steel section, exposed surface chemically cleaned capping pre-finished in baked polyester paint wall angle of size 3000mmx19mmx19mm used in the periphery of the ceiling fixed to the wall partition / RC Column / band walls with the help of screws at 600mm C/C. Main runner spaced at a 1200mm C/C suspended by using 2mm dia G.I. wire hanger securely fixed to the structural soffit of RC slab by using 6mm anchor fastener at every 1200mm(max) and 1200mm long cross tee to be interlocked between in Main runner at 600mm C/C (max) to form a grid of 1200mm x 600mm. 600mm long cross tee fixed in between 1200mm long cross tee for forming a grid of 600mm x 600mm. The rate shall be including the cost of grid system and the cost of necessary hardwares like anchor fasteners, spring steel clips, suspension rods, GI wire hangers, screws, bolt and nuts etc; Providing and laying 19mm thick, 600x600mm size Ultima/approved equivalent mineral fibre acoustic ceiling tiles with micro look edge, 60minutes fire rating as per BS 476/23 of 1987, Noise Reduction Co-efficient (NRC) of 0.70, Light Reflectance of 83%, Sound Attenuation of 30 dB, Thermal Conductivity K=0.052 W/m°K, Humidity Resistance of RH-95%. The rate shall be inclusive of wastages etc; complete.

od229233/2020_2021 : Providing and fixing in true horizontal level false ceiling of silhouette grid system with 15mm white flanges incorporating a 6mm central reveal in white / black colour of approved make using hot dipped galvanized steel section, exposed surface chemically cleaned capping pre-finished in baked polyester paint wall angle of size 3000mmx19mmx19mm used in the periphery of the ceiling fixed to the wall partition / RC Column / band walls with the help of screws at 600mm C/C. Main runner spaced at a 1200mm C/C suspended by using 2mm dia G.I. wire hanger securely fixed to the structural soffit of RC slab by using 6mm anchor fastener at every 1200mm(max) and 1200mm long cross tee to be interlocked between in Main runner at 600mm C/C (max) to form a grid of 1200mm x 600mm. 600mm long cross tee fixed in between 1200mm long cross tee for forming a grid of 600mm x 600mm. The rate shall be including the cost of grid system and the cost of necessary hardwares like anchor fasteners, spring steel clips, suspension rods, GI wire hangers, screws, bolt and nuts etc; Providing and laying 19mm thick, 600x600mm size Ultima/approved equivalent mineral fibre acoustic ceiling tiles with micro look edge, 60minutes fire rating as per BS 476/23 of 1987, Noise Reduction Co-efficient (NRC) of 0.70, Light Reflectance of 83%, Sound Attenuation of 30 dB, Thermal Conductivity K=0.052 W/m°K, Humidity Resistance of RH-95%. The rate shall be inclusive of wastages etc; complete. Suspended Hanging grid with edge trim (600x 600)

od229234/2020_2021 : Providing and fixing in true horizontal level false ceiling of silhouette grid system with 15mm white flanges incorporating a 6mm central reveal in white / black colour of approved make using hot dipped galvanized steel section, exposed surface chemically cleaned capping pre-finished in baked polyester paint wall angle of size 3000mmx19mmx19mm used in the periphery of the ceiling fixed to the wall partition / RC Column / band walls with the help of screws at 600mm C/C. Main runner spaced at a 1200mm C/C suspended by using 2mm dia G.I. wire hanger securely fixed to the structural soffit of RC slab by using 6mm anchor fastener at every 1200mm(max) and 1200mm long cross tee to be interlocked between in Main runner at 600mm C/C (max) to form a grid of 1200mm x 600mm. 600mm long cross tee fixed in between 1200mm long cross tee for forming a grid of 600mm x 600mm. The rate shall be including the cost of grid system and the cost of necessary hardwares like anchor fasteners, spring steel clips, suspension rods, GI wire hangers, screws, bolt and nuts etc; Providing and laying 19mm thick, 1200x600mm size Ultima/approved equivalent mineral fibre acoustic ceiling tiles with micro look edge, 60minutes fire rating as per BS 476/23 of 1987, Noise Reduction Co-efficient (NRC) of 0.70, Light Reflectance of 83%, Sound Attenuation of 30 dB, Thermal Conductivity K=0.052 W/m°K, Humidity Resistance of RH-95%. The rate shall be inclusive of wastages etc; complete. Suspended Hanging grid with edge trim (1200 x 600)

od229235/2020_2021 : Supplying & Installing Luxalon 300 C or equivalent Plain   aluminium metal False ceiling system manufactured by Hunter Douglas consists of panel of 300 mm wide x 30 mm deep with bevel edge manufactured out of 0.7 mm thick stove enamelled coil coated on continuous paint line aluminium Alloy AA3005/3003/3105 strips having panel length up to 3 mtrs.  The panel ends will be raised up to 29 mm. The panels about each other with a narrow ‘V’ groove. Panel shall be clipped to a baked enamelled Aluminium carrier of 41.5 mm wide x 62 mm deep x 0.95 mm thick in standard length of 5 mtrs, positioned at maximum 300 mm distance from both ends of the panels and in between at maximum distance of 1500 mm c/c. Panel carrier shall be fixed by means of M8 Rod/Bolt length not more than 250mm with nuts at 1200mm c/c to the suitable substructure provided by others at maximum at 1200mmm c/c.  The panel shall be stove enamelled coil coated in white or grey colour with thickness of 25 microns.<br>Panels: 300 mm wide x 30 mm deep with bevel edge manufactured out of 0.7 mm thick stove enamelled coil coated on continuous paint line aluminium Alloy AA 3005/3003/3105 strips  having panel length up to 3 mtrs. The panel ends will be raised up to 29 mm. The panels abut each other with a narrow ‘V’ groove<br>300 C Carrier: Aluminium carrier baked enamelled in black colour of 41.5 mm wide x 62 mm deep x 0.95 mm thick /0.5mm thick  GI in standard length of 5 mtrs.<br>Carrier Splice: Aluminium panel carrier  splice shall be used to join two carriers to continue.<br>Threaded Rod:   M8 threaded rod Used to fix or suspend the carrier from the slab/steel sub structure provided by others. <br>Edge Profile:  Aluminium 0.7mm thick edge profile of 23mm x23mm shall be used to  terminate ceilings at Perimeter in matching colour of panel.<br>

od229236/2020_2021 : Providing & fixing Armstrong/ Equivalent make Vertical Linear Baffle Ceiling made out of Aluminum Extrusion in Aluminum alloy grade 6063. The baffle blade shall be in size of 100x50x3600mm in powder coated to Approved shade. The baffle blade shall be suspended using Slotted U-profile of 20 x 30mm at on-center spacing in multiples of 25mm. Longer lengths of Baffle to be connected by Baffle Joiner and the ends to be fixed with End caps. <br>Installation of U-Grid: The U profile to be suspended at every 1200mm on-centre using 6mm threaded rod from the structural soffit using U-profile hanger. U-profile splice to be used to join more than one U profiles of length 3.75M. 1st U-Grid Channel must be no more than 400mm from the perimeter.<br>Installation of Baffles: Locate the slot for Baffle Hangers in U Profile section at 1200mm centres. Hangers are in serted into the slot, and then ins erted in the provision in the Al baffle. Two baffle hangers are required one on each side of the U-profile to hold the Al baffle in its place. Each Hanger to be secured into position by ins erting the Locking Clip. <br>When doing continuous installation, Baffles blades are to be connected at ends with Baffle Joiner, which are ins erted into the top and bottom slots of the Baffle closed profile for alignment only. The bottom Joiner to be located first and fastened on one side only. The top Joiner to be fitted then and secured with grub screws on one side. Then the two Baffle sections shall be joined and the top Joiner is screw fastened on the 2nd Baffle profile. End Caps to be located by pushing the End Cap tongues into open Baffle slots.

od229237/2020_2021 : Providing & fixing Armstrong/ Equivalent make Curved Baffle Ceiling made out of Aluminum Extrusion in Aluminum alloy grade 6063. The baffle blade shall be in size of 100x50x3600mm in powder coated to Approved shade. The baffle blade shall be suspended using Slotted U-profile of 20 x 30mm at on-center spacing in multiples of 25mm. Longer lengths of Baffle to be connected by Baffle Joiner and the ends to be fixed with End caps. <br>Installation of U-Grid: The U profile to be suspended at every 1200mm on-centre using 6mm threaded rod from the structural soffit using U-profile hanger. U-profile splice to be used to join more than one U profiles of length 3.75M. 1st U-Grid Channel must be no more than 400mm from the perimeter.<br>Installation of Baffles: Locate the slot for Baffle Hangers in U Profile section at 1200mm centres. Hangers are ins erted into the slot, and then ins erted in the provision in the Al baffle. Two baffle hangers are required one on each side of the U-profile to hold the Al baffle in its place. Each Hanger to be secured into position by ins erting the Locking Clip. <br>When doing continuous installation, Baffles blades are to be connected at ends with Baffle Joiner, which are ins erted into the top and bottom slots of the Baffle closed profile for alignment only. The bottom Joiner to be located first and fastened on one side only. The top Joiner to be fitted then and secured with grub screws on one side. Then the two Baffle sections shall be joined and the top Joiner is screw fastened on the 2nd Baffle profile. End Caps to be located by pushing the End Cap tongues into open Baffle slots.

od229238/2020_2021 : Providing and fixing in true level Open cell ‘Lock-in’ ceiling of approved make, containing ‘U’ shaped sections with sharp edges of dimensions 10mm (Flange width) X 45mm (web height) manufactured out of Aluminum of 0.50 mm gauge of Black, White or Silver Grey colours as approved. The open cell ‘Lock-in’ ceilings shall have 3 components viz. Open cell panels (top and bottom notches) of length 600mm and 1200mm, cross rails of length 1200mm, mounting rails of length 2000mm long. The Open Cell panels shall have notches on top or bottom spaced at 75mm / 100mm / 150mm / 200mm to be used with matching mounting rails and cross rails. The mounting rails are suspended at every 1200mm c/c spacing with spans longer than the length of main runner connected by means of mounting rail connectors. The above mounting rails are hung from the ceiling soffit using the same system suppliers' hangers at every 1200mm intervals. The cross rails are connected to the mounting rail at every 600mm to form a grid of 1200mm X 600mm. The ‘U’ Shaped panels are to be interlocked by matching the top and bottom notches to form tiles with cell sizes of 75mm / 100mm / 150mm / 200mm. The above tile is placed on the grid formed by mounting rails and cross rails to fit perfectly into the notches provided for this purpose. The entire suspension is connected to the wall using color matched wall moulding.

od229239/2020_2021 : Providing and fixing wooden false ceiling using 19mm BWR ply finished with  1.0 mm htick Laminate of approved make and color and with groove lines in pattern as per the instructions of the Architect. The wooden false ceiling shall be provided in combination with the gypsum boards in different levels and the The work shall be inclusive of providing framework, adequate supports using 50mm x 25mm aluminium extrusions (both ways 600mm c/c) with necessary countersunk heavy duty screws, hardware and adhesives etc; and polished teakwood edge beadings to be provided as directed.

od229240/2020_2021 : Providing and fixing Ecophon Solo Circle ceiling in size 1200mm dia X 40 mm thickness, Tiles are demountable, option of daily dusting, Vacuum cleaning, Weekly wet wiping, Panel is manufactured from high density glass wool utilizing the 3 RD technology, With Akutex FT surface on both the sides. Edges are straight cut & painted.<br>85% Light reflectance (of which more than 99% is diffuse reflection).Panel should have 2.05 sabine value at 1000mm o.d.s.Tiles withstand a permanent ambient RH upto 95% at 30*C without sagging, warping or delaminating (ISO 4611). Thermal resistance (Lambda value - 0,035-0,04 W/mK) <br>Certified by the Indoor Climate Labelling, emission class M1 for building materials and recommended by the Swedish Asthma and Allergy Association. Product Certified under GRIHA Council of India for Green ratings. Fully recyclable. The glass wool core of the element is tested and classified as non combustible according to pr EN ISO 1182 with reaction to fire classification class A2 s1 d0 according to EN 13501  - 1 - European Standard.

od174504/2021_2022 : Ecophon Solo Circle in size specified dia X 40 mm thickness, Tiles are demountable, option of daily dusting, Vacuum cleaning, Weekly wet wiping, Panel is manufactured from high density glass wool utilizing the 3 RD technology, With Akutex FT surface on both the sides. Edges are straight cut & painted.<br>85% Light reflectance (of which more than 99% is diffuse reflection).Panel should have 2.05 sabine value at 1000mm o.d.s.Tiles withstand a permanent ambient RH upto 95% at 30*C without sagging, warping or delaminating (ISO 4611). Thermal resistance (Lambda value - 0,035-0,04 W/mK) <br>Certified by the Indoor Climate Labelling, emission class M1 for building materials and recommended by the Swedish Asthma and Allergy Association. Product Certified under GRIHA Council of India for Green ratings. Fully recyclable. The glass wool core of the element is tested and classified as non combustible according to pr EN ISO 1182 with reaction to fire classification class A2 s1 d0 according to EN 13501  - 1 - European Standard. 600 mm dia

od174505/2021_2022 : Ecophon Solo Circle in size specified dia X 40 mm thickness, Tiles are demountable, option of daily dusting, Vacuum cleaning, Weekly wet wiping, Panel is manufactured from high density glass wool utilizing the 3 RD technology, With Akutex FT surface on both the sides. Edges are straight cut & painted.<br>85% Light reflectance (of which more than 99% is diffuse reflection).Panel should have 2.05 sabine value at 1000mm o.d.s.Tiles withstand a permanent ambient RH upto 95% at 30*C without sagging, warping or delaminating (ISO 4611). Thermal resistance (Lambda value - 0,035-0,04 W/mK) <br>Certified by the Indoor Climate Labelling, emission class M1 for building materials and recommended by the Swedish Asthma and Allergy Association. Product Certified under GRIHA Council of India for Green ratings. Fully recyclable. The glass wool core of the element is tested and classified as non combustible according to pr EN ISO 1182 with reaction to fire classification class A2 s1 d0 according to EN 13501  - 1 - European Standard. 1000 mm dia

od174506/2021_2022 : Ecophon Solo Circle in size specified dia X 40 mm thickness, Tiles are demountable, option of daily dusting, Vacuum cleaning, Weekly wet wiping, Panel is manufactured from high density glass wool utilizing the 3 RD technology, With Akutex FT surface on both the sides. Edges are straight cut & painted.<br>85% Light reflectance (of which more than 99% is diffuse reflection).Panel should have 2.05 sabine value at 1000mm o.d.s.Tiles withstand a permanent ambient RH upto 95% at 30*C without sagging, warping or delaminating (ISO 4611). Thermal resistance (Lambda value - 0,035-0,04 W/mK) <br>Certified by the Indoor Climate Labelling, emission class M1 for building materials and recommended by the Swedish Asthma and Allergy Association. Product Certified under GRIHA Council of India for Green ratings. Fully recyclable. The glass wool core of the element is tested and classified as non combustible according to pr EN ISO 1182 with reaction to fire classification class A2 s1 d0 according to EN 13501  - 1 - European Standard. 1500mm dia

od229242/2020_2021 : Providing & fixing accoustic fabric baffle ceiling of Anutone Subtex Wave Hush 600x1200x50 , Square edge<br>Supply and Installation of Anutone Subtex Wave Hush,square edge, FR Grade, Fabric finish glassfibre core panel of size 600x1200x50mm having volume density 120Kgs/m3, weight 6kg/m2, suspended individually and vertically with pre-fixed D-rings by using 3mm Dia hanger wire and levelling clip (wire and clip not by Anutone). Wire to be first dro pped from the slab to desired height as per architectural drawing with suitable cleats/anchor bolts. Anutone Subtex wave Hush panels are then hung using pre-fixed D-rings and hanger wires.<br>Technical Parameters <br>• Fire (Class) – 1 & P<br>• Acoustics – NRC 0.9<br>• Thermal conductivity (W/mk)– 0.07<br>• Climate (°C, RH) – 49, 95<br>• Light reflectance (%) – Colour dependant<br>• Green (VoC, RC %) – Low, 25

od229243/2020_2021 : Supplying and fixing wooden box using 18 mm MDF and finished with Duco paint finsih WITH NECESSARY CEILING SUPPORTS

od229244/2020_2021 : Providing and fixing AMF Heradesign Fine, 1 layer magnesite bonded wood wool acoustic panel, fibre with 1mm, exquisite surface structure, building biology recommended, size 600 x 600 x 15 mm /1200 x 600 x 15mm, having edge detail SK-04, weight 7.80 Kg/Sqm, fire protection class B-s1,d0 as per EN 13501-1 & Humidity Resistance of 95%. Thickness Tolerance T2 (± 1 mm) according to EN 13168. Wood wool panels to be PEFC certified & should bear the Forest Stewardship Council Seal confirming that the wood used originates from responsibly managed forests. Panels to be laid on AMF T24 grids formed into 600mm x 600mm modules using Main Tee having 38mm web height and length 3600mm, Cross Tee having 29mm web height and lengths 1200mm & 600mm and Wall Angle 20mm x 14mm and length of 3000mm. Providing & fixing of 40mm thick glass wool slab having a density of 50kg/m3. The wood wool panels have to be installed at a distance of 300 mm from the soffit to achieve a NRC of 0.90 as per ASTM C423. Extra supports to be provided to support the weight of wood wool panels as recommended by the manufacturer. Rate includes the spray painting over the panels with approved color.

9.133.1.1 : Providing and fixing, in position concealed G.I. section for wall paneling using board of required thickness fixed on the 'W' profile (0.55 mm thick) having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall screws. Board is fixed to the 'W' profile with 25 mm countersunk ribbed head screws @ 200 mm C/C., all complete as per the drawing & directions of engineer-in-charge, the joints of the boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide seamless finish.Tapered edge calcium silicate board made with calcareous & siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with compressive strength 225 kg/sqcm, Bending strength 100 kg/ sqcm.10 mm Thick

od229246/2020_2021 : Supply and fixing of Wooden Trap door in gyp ceiling corridors of 1200 mm x 600 mm size. The rate shall include for providing 50mmx50mm teak wood framework with 12mm thick BWR ply placed at bottom of the false ceiling level.The exposed surface of plywood is finished with 1mm thick laminate of matching colour of the false ceiling and other the other surfaces inside the frame work and plywood shall be finished with two coats of matt enamel paint over a coat of primer and putty as directed.

od229247/2020_2021 : Supply and fixing of Vox Infratop false ceiling manufactured in europe, of panel sizes of 340mmx 2700mm, durable and resistant to moisture, water and borer-fungus-termite attack. Panels to be installed with GI / Alumnium sections of suitable gauge & size according to site conditions . Panels SV 08/07 &09 with suitable trims SV 15 with dimensions 40x19x22x12x3050 (all in mm) for edge profiles and SV 18 with dimensions 67x3050 mm with T head of 42mm for Connecting profiles . Panels must be maintainance free , rust proof and are 100% Water proof . Advised especially for Soffit areas , under the roof installation . 10 years warranty for colour & finish of the panels and the profiles from VOX.

od229248/2020_2021 : ACP falseceiling : Providing and fixing the Falseceiling with the Laminated sandwiched composite panel of Alucobond or Knauf of Fameline make or Alpolic make with approved colour and shade (4 mm (0.5 + 3.0 + 0.5) ACP with 5000 series with 70% Virgin Mineral white core & 30% Resin polymer as per the specification as per profile and shape shown in the Drawing with necessary support from the ceiling. Rate shall include the cost of supplying and fixing of Laminated sandwiched composite panel, Non staining weather for Vertical & horizontal joints in general the frame work for ACP cladding consists of aluminium anodized box frame All Bolts, nuts and screws shall be SS 316 grade of approved make.

od229249/2020_2021 : Euro cell Ceiling<br>Supply of euroceil make / Equivalent stretch ceiling comprising Aluminium Channels and PVC Translucent membrane with PVC gripper Colour : White ( EC5-TR-4011). HSN 3918.10.00. <br>Sheet Installation Charges. SAC 995478<br>Supply of OSRAM LED Modules with Compatible Drivers. (Non-Dimmable) CCT: 3000K / 4000K /6500K HSN 9405.10.90 lux Level: Min: 300 lms at 1.5mtr height from stretch ceiling. LED Installation Charges SAC 995461. Rate includes Design, Artwork and Base frame work

12.45.3 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum moisture resistant board

12.52.1 : Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge.GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending

JOINERIES

od131025/2020_2021 : Wide line Door Frames of approved make : Supplying, receiving, unloading, storing and installation of proprietary type wide line door frames (25mm depth) of approved make using proprietary designed hinges. The section shall be matt natural anodized as per manufacturer's specification and the cost shall be including the cost of all necessary hardwares.

od131063/2020_2021 : Wide line Door Frames of approved make for Access control system doors: Co-ordination with the supplier, receiving, unloading, storing and installation of proprietary type wide line door frames (50mm depth) of approved make using proprietary designed hinges. The section shall be matt natural anodized as per manufacturer's specification and the cost shall be including the cost of all necessary hardwares.

od131069/2020_2021 : Supply & Fixing of Glass Door (Single Leaf) of 12mm toughened glass with Hafele/ Dorma make  fittings  and  wideline frames  all around the glass and shutter . The  profiles shall be suitable for Glass thickness of  12 mm.The Profile shall be matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with 2 mm Gauge thickness Excluding 20 Micron of Anodizing.<br>Single leaf door of size 1100 x 2400mm necessary Hafele make hardwares as mentioned in the drawings

od131277/2020_2021 : Supply & Fixing of Glass Door (Double Leaf) of 12mm toughened glass with Hafele/ Dorma make  fittings  and  wideline frames  all around the glass and shutter . The  profiles shall be suitable for Glass thickness of  12 mm.The Profile shall be matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with 2 mm Gauge thickness Excluding 20 Micron of Anodizing.<br>Double leaf door of size 1500 x 2400mm necessary Hafele make hardwares as mentioned in the drawings

od232140/2020_2021 : Providing and fixing 1200mm x 2400mm size manual sliding door, using 38mm thick flush door shutters of single leaf, solid core of block board type bonded with phenol formaldehyde synthetic resin thermo pressed with 8mm thick teak wood external lipping. The construction procedure of the shutter should be as per IS:2202. The shutter shall be shop prepared for taking mortice lock or latches suitable with block of wood may be provided for fixing the hardware. The size of block, shall perfectly correspond to the maximum size of lock, covered in IS:2209. All the four edges of the door shutter shall be square. The shutter shall be free from twist or warp in its plane and of required size etc; complete as directed. Providing and finishing the flush door shutters on both sides with 1.00mm thick approved make and shade laminate sheets at factory by hot pressing with grooves and lines in pattern as per the instructions of the Architect. The rate shall be inclusive of polishing the the lippings with PU polish upto the required level. The basic cost of 1.00mm thick laminate is Rs.400/sqm. The rate should be include the cost of supply and fixing one number approved make, SS316 grade Mortice Sash lock ST8100 type with aproved type lever handle and internal thump turn in stainless steel satin finish, SS-316 grade with lock forend with Euro profile cylinder with external key operation and Internal thump turn and the strike plate and approved make SS sliding channel along with sliding arrangement in shutters including all accessories.

PASSIVE FIRE STOP APPLICATION FOR FLOOR OPENINGS

od59444/2021_2022 : Electrical Shaft/Busbar/Communication Shaft - ECO /DCO-Supply and installation of Fire Barrier mortar (HILTI CP 636 or Approved equivalent) with minimum 2 (Four)hours fire rating when tested in accordance with UL 1479 standards , for fire rated vertical openings in floors or slabs and floors made of concrete, masonry, metal, gypsum partition, after passing service lines like Cable,Cable trays, Bus Duct or Metal pipes. The mortar shall be a light weight cementitious product and shall carry test certificate in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. Expanding fire stop foam (HILTI CP 620 or Approved Equivalent) with minimum 2 hours fire rating when tested in accordance with UL 1479 standards, shall be used to seal areas that are highly dense or are not accessible and cannot be sealed with fire stop mortar properly. The expanding foam shall expand minimum seven times its volume to fill the cavity at the time of dispensing the material and shall fully cure within two minutes after dispensing. The expanding foam shall also be repenetratable. The products shall be age tested as per Dafstb and DIBT standards. The products shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96. The products shall be UL listed & classified and shall bear the UL approval logo on the packing. The rate shall include the mineral wool and miscellaneous items etc.., (Ratio of Mortar to foam can be assumed as 75% & 10% Respectively).Assumed 15% Penetrants Occupancy.An Engineering Judgement from the Manufacturer is required for Shaft sizes as per openings as per the cable occupancy .,,Firestop installation should be done by Hilti Accredated Firestop Speciality Contractor (HAFSC) and in accordance with Hilti guidelines

od59537/2021_2022 : Fire Shaft - FCO-Supply and installation of Fire stop mortar system (HILTI CP 636 or Approved Equivalent) with minimum 2 hours fire rating when tested in accordance with UL 1479 standards, for openings in floors or slabs after passing service lines like Metal Pipes. The mortar shall be a light weight cementitious product and shall carry test certificate in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. The product shall be age tested as per Dafstb and DIBT standards. The product shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96. The product shall be UL listed & classified and shall bear the UL approval logo on the packing. The rate shall include the mineral wool And other miscellaneous items etc.., Assumed 15% Penetrants Occupancy.An Engineering Judgement from the Manufacturer is required for Shaft sizes as per openings as per the cable occupancy .,,Firestop installation should be done by Hilti Accredated Firestop Speciality Contractor (HAFSC) and in accordance with Hilti guidelines

od59554/2021_2022 : Plumbing /Other PVC pipes shaft - TCO / GCO/KCO-Supply and installation Fire stop mortar system (HILTI CP 636 or Approved equivalent ) with minimum 2 hours fire rating when tested in accordance with UL 1479 standards, for horizontal openings in floors or slabs after passing Plastic or Metal Pipes. The mortar shall be a light weight cementitious product and shall carry test certificate in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. Fire intumescent sealants (HILTI FS ONE or Approved equivalent ) (for plastic pipe diameter <= 2''), Intumescent Wraps ( HILTI CP 648-E or Approved equivalent ) (for plastic pipe diameter > 2'' & <= 6'' mm) & Intumescent Collars (for plastic pipe diameter > 6'' mm & <= 10'' ) shall be used around Plastic Pipes or Conduits to provide minimum 2 hours fire rating when tested in accordance with UL 1479 standards. The products shall be age tested as per Dafstb and DIBT standards. The products shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96. The products shall be UL listed & classified and shall bear the UL approval logo on the packing. The rate shall include the mineral wool and other miscellaneous items etc..,Assumed 15% Penetrants Occupancy.An Engineering Judgement from the Manufacturer is required for Shaft sizes as per openings as per the cable occupancy .,,Firestop installation should be done by Hilti Accredated Firestop Speciality Contractor (HAFSC) and in accordance with Hilti guidelines

od59625/2021_2022 : Supply and installation Fire stop mortar system (HILTI CP 636 or Approved equivalent ) with minimum 2 hours fire rating when tested in accordance with UL 1479 standards, for horizontal openings in floors or slabs after passing Plastic or Metal Pipes. The mortar shall be a light weight cementitious product and shall carry test certificate in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. Fire intumescent sealants (HILTI FS ONE or Approved equivalent ) (for plastic pipe diameter <= 2''), Intumescent Wraps ( HILTI CP 648-E or Approved equivalent ) (for plastic pipe diameter > 2'' & <= 6'' mm) & Intumescent Collars (for plastic pipe diameter > 6'' mm & <= 10'' ) shall be used around Plastic Pipes or Conduits to provide minimum 2 hours fire rating when tested in accordance with UL 1479 standards. The products shall be age tested as per Dafstb and DIBT standards. The products shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96. The products shall be UL listed & classified and shall bear the UL approval logo on the packing. The rate shall include the mineral wool and other miscellaneous items etc..,Assumed 15% Penetrants Occupancy.An Engineering Judgement from the Manufacturer is required for Shaft sizes as per openings as per the cable occupancy .,,Firestop installation should be done by Hilti Accredated Firestop Speciality Contractor (HAFSC) and in accordance with Hilti guidelines. Below Items shall comply to the above Specifications text and will be used as per penetrant ( To be quantified as per actuals at Site as suggested by Hilti Fire Stop Consultant )-Plastic Pipe diameter of 1'' (Firestop Sealant)

od59626/2021_2022 : Supply and installation Fire stop mortar system (HILTI CP 636 or Approved equivalent ) with minimum 2 hours fire rating when tested in accordance with UL 1479 standards, for horizontal openings in floors or slabs after passing Plastic or Metal Pipes. The mortar shall be a light weight cementitious product and shall carry test certificate in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. Fire intumescent sealants (HILTI FS ONE or Approved equivalent ) (for plastic pipe diameter <= 2''), Intumescent Wraps ( HILTI CP 648-E or Approved equivalent ) (for plastic pipe diameter > 2'' & <= 6'' mm) & Intumescent Collars (for plastic pipe diameter > 6'' mm & <= 10'' ) shall be used around Plastic Pipes or Conduits to provide minimum 2 hours fire rating when tested in accordance with UL 1479 standards. The products shall be age tested as per Dafstb and DIBT standards. The products shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96. The products shall be UL listed & classified and shall bear the UL approval logo on the packing. The rate shall include the mineral wool and other miscellaneous items etc..,Assumed 15% Penetrants Occupancy.An Engineering Judgement from the Manufacturer is required for Shaft sizes as per openings as per the cable occupancy .,,Firestop installation should be done by Hilti Accredated Firestop Speciality Contractor (HAFSC) and in accordance with Hilti guidelines. Below Items shall comply to the above Specifications text and will be used as per penetrant ( To be quantified as per actuals at Site as suggested by Hilti Fire Stop Consultant )-Plastic Pipe diameter of 2'' (Firestop Sealant)

od59627/2021_2022 : Supply and installation Fire stop mortar system (HILTI CP 636 or Approved equivalent ) with minimum 2 hours fire rating when tested in accordance with UL 1479 standards, for horizontal openings in floors or slabs after passing Plastic or Metal Pipes. The mortar shall be a light weight cementitious product and shall carry test certificate in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. Fire intumescent sealants (HILTI FS ONE or Approved equivalent ) (for plastic pipe diameter <= 2''), Intumescent Wraps ( HILTI CP 648-E or Approved equivalent ) (for plastic pipe diameter > 2'' & <= 6'' mm) & Intumescent Collars (for plastic pipe diameter > 6'' mm & <= 10'' ) shall be used around Plastic Pipes or Conduits to provide minimum 2 hours fire rating when tested in accordance with UL 1479 standards. The products shall be age tested as per Dafstb and DIBT standards. The products shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96. The products shall be UL listed & classified and shall bear the UL approval logo on the packing. The rate shall include the mineral wool and other miscellaneous items etc..,Assumed 15% Penetrants Occupancy.An Engineering Judgement from the Manufacturer is required for Shaft sizes as per openings as per the cable occupancy .,,Firestop installation should be done by Hilti Accredated Firestop Speciality Contractor (HAFSC) and in accordance with Hilti guidelinesBelow Items shall comply to the above Specifications text and will be used as per penetrant ( To be quantified as per actuals at Site as suggested by Hilti Fire Stop Consultant )-Plastic Pipe diameter of 2.5'' (Firestop Wrap), Min. recommended hole dia. in wall/floor: 92 mm

od59628/2021_2022 : Supply and installation Fire stop mortar system (HILTI CP 636 or Approved equivalent ) with minimum 2 hours fire rating when tested in accordance with UL 1479 standards, for horizontal openings in floors or slabs after passing Plastic or Metal Pipes. The mortar shall be a light weight cementitious product and shall carry test certificate in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. Fire intumescent sealants (HILTI FS ONE or Approved equivalent ) (for plastic pipe diameter <= 2''), Intumescent Wraps ( HILTI CP 648-E or Approved equivalent ) (for plastic pipe diameter > 2'' & <= 6'' mm) & Intumescent Collars (for plastic pipe diameter > 6'' mm & <= 10'' ) shall be used around Plastic Pipes or Conduits to provide minimum 2 hours fire rating when tested in accordance with UL 1479 standards. The products shall be age tested as per Dafstb and DIBT standards. The products shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96. The products shall be UL listed & classified and shall bear the UL approval logo on the packing. The rate shall include the mineral wool and other miscellaneous items etc..,Assumed 15% Penetrants Occupancy.An Engineering Judgement from the Manufacturer is required for Shaft sizes as per openings as per the cable occupancy .,,Firestop installation should be done by Hilti Accredated Firestop Speciality Contractor (HAFSC) and in accordance with Hilti guidelines. Below Items shall comply to the above Specifications text and will be used as per penetrant ( To be quantified as per actuals at Site as suggested by Hilti Fire Stop Consultant )-Plastic Pipe diameter of 3'' (Firestop Wrap), Min. recommended hole dia. in wall/floor: 112 mm

od59629/2021_2022 : Supply and installation Fire stop mortar system (HILTI CP 636 or Approved equivalent ) with minimum 2 hours fire rating when tested in accordance with UL 1479 standards, for horizontal openings in floors or slabs after passing Plastic or Metal Pipes. The mortar shall be a light weight cementitious product and shall carry test certificate in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. Fire intumescent sealants (HILTI FS ONE or Approved equivalent ) (for plastic pipe diameter <= 2''), Intumescent Wraps ( HILTI CP 648-E or Approved equivalent ) (for plastic pipe diameter > 2'' & <= 6'' mm) & Intumescent Collars (for plastic pipe diameter > 6'' mm & <= 10'' ) shall be used around Plastic Pipes or Conduits to provide minimum 2 hours fire rating when tested in accordance with UL 1479 standards. The products shall be age tested as per Dafstb and DIBT standards. The products shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96. The products shall be UL listed & classified and shall bear the UL approval logo on the packing. The rate shall include the mineral wool and other miscellaneous items etc..,Assumed 15% Penetrants Occupancy.An Engineering Judgement from the Manufacturer is required for Shaft sizes as per openings as per the cable occupancy .,,Firestop installation should be done by Hilti Accredated Firestop Speciality Contractor (HAFSC) and in accordance with Hilti guidelines. Below Items shall comply to the above Specifications text and will be used as per penetrant ( To be quantified as per actuals at Site as suggested by Hilti Fire Stop Consultant )-Plastic Pipe diameter of 4'' (Firestop Wrap), Min. recommended hole dia. in wall/floor: 132 mm

od59630/2021_2022 : Supply and installation Fire stop mortar system (HILTI CP 636 or Approved equivalent ) with minimum 2 hours fire rating when tested in accordance with UL 1479 standards, for horizontal openings in floors or slabs after passing Plastic or Metal Pipes. The mortar shall be a light weight cementitious product and shall carry test certificate in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. Fire intumescent sealants (HILTI FS ONE or Approved equivalent ) (for plastic pipe diameter <= 2''), Intumescent Wraps ( HILTI CP 648-E or Approved equivalent ) (for plastic pipe diameter > 2'' & <= 6'' mm) & Intumescent Collars (for plastic pipe diameter > 6'' mm & <= 10'' ) shall be used around Plastic Pipes or Conduits to provide minimum 2 hours fire rating when tested in accordance with UL 1479 standards. The products shall be age tested as per Dafstb and DIBT standards. The products shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96. The products shall be UL listed & classified and shall bear the UL approval logo on the packing. The rate shall include the mineral wool and other miscellaneous items etc..,Assumed 15% Penetrants Occupancy.An Engineering Judgement from the Manufacturer is required for Shaft sizes as per openings as per the cable occupancy .,,Firestop installation should be done by Hilti Accredated Firestop Speciality Contractor (HAFSC) and in accordance with Hilti guidelines. Below Items shall comply to the above Specifications text and will be used as per penetrant ( To be quantified as per actuals at Site as suggested by Hilti Fire Stop Consultant )-Plastic Pipe diameter of 5'' (Firestop Wrap), Min. recommended hole dia. in wall/floor: 152 mm

od59631/2021_2022 : Supply and installation Fire stop mortar system (HILTI CP 636 or Approved equivalent ) with minimum 2 hours fire rating when tested in accordance with UL 1479 standards, for horizontal openings in floors or slabs after passing Plastic or Metal Pipes. The mortar shall be a light weight cementitious product and shall carry test certificate in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. Fire intumescent sealants (HILTI FS ONE or Approved equivalent ) (for plastic pipe diameter <= 2''), Intumescent Wraps ( HILTI CP 648-E or Approved equivalent ) (for plastic pipe diameter > 2'' & <= 6'' mm) & Intumescent Collars (for plastic pipe diameter > 6'' mm & <= 10'' ) shall be used around Plastic Pipes or Conduits to provide minimum 2 hours fire rating when tested in accordance with UL 1479 standards. The products shall be age tested as per Dafstb and DIBT standards. The products shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96. The products shall be UL listed & classified and shall bear the UL approval logo on the packing. The rate shall include the mineral wool and other miscellaneous items etc..,Assumed 15% Penetrants Occupancy.An Engineering Judgement from the Manufacturer is required for Shaft sizes as per openings as per the cable occupancy .,,Firestop installation should be done by Hilti Accredated Firestop Speciality Contractor (HAFSC) and in accordance with Hilti guidelines Below Items shall comply to the above Specifications text and will be used as per penetrant ( To be quantified as per actuals at Site as suggested by Hilti Fire Stop Consultant )-Plastic Pipe diameter of 6'' (Firestop Wrap), Min. recommended hole dia. in wall/floor: 202 mm

od59632/2021_2022 : AHU/HVAC/ Land scape Terrace Services Shaft - ACO / SPCO -Supply and installation of Fire stop mortar system (HILTI CP 636 or Approved equivalent ) with minimum 2 hours fire rating in services passing through fire rated walls and floors made of concrete, masonry, metal, gypsum partition when tested in accordance with UL 1479 standards, for horizontal openings in floors or slabs after passing service lines like Metal Pipes or Ducts. The mortar shall be a light weight cementitious product and shall carry test certificate in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. Acrylic fire stop sealant ( HILTI CP606 or Approved Equivalent )with minimum 2 hours fire rating when tested in accordance with UL 1479 standards, shall be used along the periphery of ducts & chiller pipes without insulation. Fire intumescent firestop sealant (HILTI FS one or Approved equivalent, )with minimum 2 hours fire rating when tested in accordance with UL 1479 standards, shall be used along the periphery of ducts & chiller pipes with insulation. The products shall be age tested as per Dafstb and DIBT standards. The products shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96. The products shall be UL listed & classified and shall bear the UL approval logo on the packing. The rate shall include the mineral wool and checkered plate and other miscellaneous items etc.., (Ratio of Mortar to sealant can be assumed as 70% & 5% Respectively). Assumed 25% Penetrants Occupancy.An Engineering Judgement from the Manufacturer is required for Shaft sizes as per openings as per the cable occupancy .,,Firestop installation should be done by Hilti Accredated Firestop Speciality Contractor (HAFSC) and in accordance with Hilti guidelines

od59633/2021_2022 : Individual Metal pipes (Smaller gaps upto 50 mm)-Supply and installation of Acrylic fire stop sealant ( HILTI CP606 or Approved Equivalent )with minimum 2 hours fire rating when tested in accordance with UL 1479 standards, shall be used along the periphery of ducts & chiller pipes without insulation passing through fire rated walls and floors made of concrete, masonry, metal, gypsum construction to provide up to 2 hours insulation and integrity when subject to the test conditions of UL 1479 standards. The product shall also be age tested as per DafStb guidelines. Sealant to provide sufficient MAF, water and gas tight seal apart from providing an airborne sound transmission reduction (STC of 50) and shall be tested as per DIN 52210 for sound insulation . The product should be tested for mold resistance rating of 0 as determined by ASTM G21-96 and should have a VOC content of approx. 75 g/l as per LEED 2009. The sealant shall be FM approved. All installations to be in full accordance with the manufacturer. The sealant should be tested in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. The product shall bear the UL and FM approval logo on the packing where applicable. The rate shall include the mineral wool backing material and other miscellaneous items etc.., Assumed 15% Penetrants Ocupancy.An Engineering Judgement from the Manufacturer is required for Shaft sizes as per openings as per the cable occupancy .,,Firestop installation should be done by Hilti Accredated Firestop Speciality Contractor (HAFSC) and in accordance with Hilti guidelines

od59634/2021_2022 : Passive Fire Stopping Solution for Curtain Wall for Glazing Spandrel Area -Providing sprayable Fire-rated joint spray Hilti CFS SP WB to provide minimum 2 hours of fire rating when tested as per ASTME E 2307 and UL 2079 standard . The product to have upto 50% Movement Capability and Sound Insulation of 55db as per ASTME-90. The product shall have passed the 500 cycles requirement as specified by ASTM E 1399 class II. The product shall carry carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96 and shall have a VOC content of approx. 60 g/l as per LEED 2009. The product shall carry test certificate as per ASTM E 1399 class II for movement capability. The product shall be UL listed & Classified and shall bear the UL and FM approval logo on the packing. Firestop installation should be done by Hilti trained applicators and in accordance with Hilti guidelines ; in case of a non standard system an Engineering Judgement from the manufacturer to be done to comply ASTM E 2307 (ASSUMED 100 MM GAP WIDTH)

water proofing works

od179476/2021_2022 : TOILET SUNKEN AREA -Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc. by applying cement slurry mixed with Approved Acrylic Polymer in the following order and consisting of applying:1) plaster layer of 12mm thick Cement Mortar 1:4 (1 cement: 4 coarse sand) admixed with Normal setting integral Waterproofing compound of approved meke conforming to IS 2645 at the rate of 2% by weight of cement over the prepared surface. Plaster shall be cured by spraying of water for the next 48 hours.ii) First layer of slurry of cement @ 0.488 kg/sqm. mixed with Approved Acrylic Polymer 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. iii) Third layer of 1.5mm thickness consisting of slurry of cement @ 1.289 kg./sqm. mixed with Approved Acrylic Polymer @ 0.670 kg/sqm. and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 6 hours. iv) Lay protective plaster layer with 12mm thick Cement Mortar 1:4 (1 cement: 4 coarse sand) admixed with Normal setting integral Waterproofing compound of approved make conforming to IS 2645 at the rate of 2% by weight of cement over the third coat of brush topping. Plaster shall be cured by spraying of water for the next 7days. v)The whole surface so finished shall be flooded with water for a minimum period of two weeks for curing and testing of treatment. In case of any leakage, required rectifications shall be carried out as per directions of Engineer-in-Charge and the surface retested. Note- The length and width of the area to be treated shall be measured correct to a cm and its area for payment shall be calculated in square metres correct to two places of decimal The rate includes preparation of surcace, treatment and sealing of all joints, corners, junctions of pipes and masonary with polymer mixed slurry all complete as per direction of Engineer in charge. Toilet sunken bottom area

od179483/2021_2022 : 2) Sealing the pipe sleeves with Approved waterproofing Grout - GP

od179484/2021_2022 : 3) Supplying and filling the sunken slab area by BRICK-BATCOBA by adding integral Waterproofing compound approved make admixture at the rate specified in the manufacturer's specification after entire completion of laying pipes, sanitary fittings etc. Rate shall include for preparation of surface, protecting the laid pipes and sanitary fittings, finishing the surface smooth to receive the top coat of water proofing application etc. complete and all as directed.

od179487/2021_2022 : 4) Toilet Floor Treatment after filling-Providing and laying water proofing treatment in WCs, bathroom etc. over vermiculate concrete by applying cement slurry mixed with Acrylic Polymer of Approved manufacturer in the following order and consisting of applying: First layer of slurry of cement @ 0.488 kg/sqm. mixed with Acrylic Polymer @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours.ii) third layer of 1.5mm thickness consisting of slurry of cement @ 1.289 kg./sqm. mixed with Acrylic Polymer @ 0.670 kg/sqm. and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 6 hours.iii) Lay protective plaster layer with 12mm thick Cement Mortar 1:4 (1 cement: 4 coarse sand) admixed with Normal setting integral Waterproofing compound of approved make conforming to IS 2645 at the rate of 2% by weight of cement over the third coat of brush topping. Plaster shall be cured by spraying of water for the next 7days. Note- The length and width of the PCC area to be treated shall be measured correct to a cm and its area for payment shall be calculated in square metres correct to two places of decimal The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonary with polymer mixed slurry all complete as per direction of Engineer in charge.

FLOORING

od170867/2021_2022 : Providing flooring with approved quality granite slab not less than 20mm thick of size 1200mm x 900mm or 900mm x 600mm or 600mm x 600mm, machine cut and machine high pre-polished, set in C.M 1:4, 20mm thick topped with white cement slurry (for surface contact of the bottom of the granite slab) as per approved pattern / design including finishing the joints with white cement slurry, cutting, edge chamfering ,nosing ,making grooves and polishing rough, medium, nice and acid wash and tin-oxide polish as per manufacturer's Specification and as directed. The work shall include for preparation of base surface & finish the surface, protection with gypsum/pop layer over plastic sheet and removing the same before handing over, work at all levels and as directed. The tolerance in level shall be +/-1mm. The item shall include cutting the granite as necessary for all services like floor trap,clean out etc., complete (Basic Rate Rs. 2000 /sqm)

od170877/2021_2022 : Providing and laying of approved make 100% Optimum SD Nylon Tufted, Textured Loop Pile carpet tiles of density more than 6500 oz and20oz/sq.mtr of size 600mmx600mm or any standard size,permanent static control, solution dyed, pile height about 0.118inches with PVC free backing, colorfastness > or =4 after 100hours, moth proof, stain resistant etc. complete, over existing flooring as per Manufacturer's specification. The carpet should be ,class-1 fire rated ,antistatic, moisture barrier, etc. Plank/square (approved shade basic cost Rs.1200/Sqm). The rate shall be include the cost of the supply of carpet necessary adhesive. (Basic Rate Rs.2000 /sqm)

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

11.41.3 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 800x 800 mm

11.41.4 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 1000x1000 mm

od171026/2021_2022 : Providing, laying & levelling Specially designed concrete Mix (M15) with average thickens of 100mm including application of hardener & release agent as per requirement and stamping the same as per approved patterns, groove cuttings & application of sealing Coat.

11.47.2 : Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer,in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm

11.47.3 : Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer,in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 800x800 mm

11.47.4 : Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer,in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 1000x1000 mm

od174426/2021_2022 : Providing and laying of total thick 17 mm hard wood flooring but in general it shall be provided with 14 mm thick planks of size 188 x 2525 mm in three layer construction with approved variety of 3.6 mm top species ( Cherry/ Oak/ Beech / Merbau ) with 7 coats of formaldehyde - free lacquer in factory finish with tongue and groove joints , glue fixed and edges finished with necessary profiles of skirting / reducer as per manufactures specification.<br>The work shall be inclusive of providing polyethene sheets as under lay on the existing floor.<br>Note: Approved make shall be Tarkett Sommer

od174436/2021_2022 : Providing & Laying Athangudi Tile as per approved design & pattern with minimum thickness of 20 mm & laid on 20mm thick cement mortar (1:4) including grouting the joints with white cement/ matching pigments etc. complete

od174448/2021_2022 : Providing & laying Red Oxide /Black Oxide of minimum Thickness 4 mm finished to smooth including preparation of Concrete surface and Form works(If any)

od175074/2021_2022 : Preparing the surface with 25-40 mm thick concrete screed( 1:2:4) by using coarse graded aggregate of 6 to 12 mm size laid over floor concrete and finished smooth and even surface to receive the Tile adhesive/Cement mortar as instructed by Client. Thickness 75 mm thick

od175075/2021_2022 : Preparing the surface with 25-40 mm thick concrete screed( 1:2:4) by using coarse graded aggregate of 6 to 12 mm size laid over floor concrete and finished smooth and even surface to receive the Tile adhesive/Cement mortar as instructed by Client. Thickness up to 25 mm

od175076/2021_2022 : Preparing the surface with 25-40 mm thick concrete screed( 1:2:4) by using coarse graded aggregate of 6 to 12 mm size laid over floor concrete and finished smooth and even surface to receive the Tile adhesive/Cement mortar as instructed by Client. Thickness Up to 40 mm

11.48.2 : Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm

11.48.3 : Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 800x800mm

11.48.4 : Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 1000x1000 mm

11.50 : Deduct for not grouting the joints with white cement and matching pigment in the items of fixing of vitrified tiles

od175219/2021_2022 : Finishing with Epoxy Flooring of approved colour/thickness all locations as per Manufacturer's specifications including appropriate priming coat, preparation of surface etc. complete on concrete works.

FALSE CEILING WORKS

od170851/2021_2022 : Acoustic baffle Wooden ceiling-Anutone Salon Sonator Wave Perfs 400x1200x25mm thk, Square edge.Supply & installation of Anutone Salon Sonator Wave Perfs, made of pinewood E1 grade fiberboard, with Ranurado 6R32| Cuadrado 25/50 | Circulo 25/50 perforations with black acoustical fleece sandwiched inbetween,melamine finish, 5-test fire retardant grade, size 400x1200x25mm, square edge, volume density of base board 750Kg/m3, weight 19Kgs/m2,suspended from the soffit slab to desired height and span distance by using Anutone Strut U-ClipHD25 Kit.Anutone Strut U-ClipHD25 is first fastened to Sonator Wave using supplied sleeve fasteners at 50-100mm from edge and 500-600mm centres. Strut U-ClipHD25 is then connected to the Kit-supplied Anchor wire with Levelling hook. <br>Salon Sonator Wave Perfs are then suspended using Anchor Bolt, Soffit Cleat and S-hook from the soffit slab and levelled into designed position. (Anchor bolts, Soffit Cleat and S-hook not by Anutone). Technical Parameters:• Fire (Class) – 1 & P<br>• Thermal conductivity (W/mk)– na<br>• Climate (°C, RH) – 50, 70<br>• Light reflectance (%) – Colour Dependant<br>• Green (VOC, RC %) – Low, 25

od170854/2021_2022 : Providing and fixing Acoustic baffle Wooden screen ceiling of approved item as per engineer-in-charge.Anutone Salon Sonator Duo 400x1200x16mm thk, Square edge.Supply & installation of Anutone Sonator duo, made of pinewood E1 grade fiberboard, wooden plain panel, melamine finish, 5-test fire retardant grade, size 400x1200x16mm, square edge, volume density of base board 750Kg/m3, weight 12Kgs/m2,suspended from the soffit slab to desired height and span distance by using Anutone Strut U-ClipHD15 Kit.Anutone Strut U-ClipHD15 is first fastened to Sonator Duo using supplied sleeve fasteners at 50-100mm from edge and 500-600mm centres. Strut U-ClipHD15 is then connected to the Kit-supplied Anchor wire with Levelling hook. Salon Sonator Duo are then suspended using Anchor Bolt, Soffit Cleat and S-hook from the soffit slab and levelled into designed position. (Anchor bolts, Soffit Cleat and S-hook not by Anutone). Technical Parameters :• Fire (Class) – 1 & P• Thermal conductivity (W/mk)– na• Climate (°C, RH) – 50, 70• Light reflectance (%) – Colour Dependant• Green (VOC, RC %) – Low, 25

od170860/2021_2022 : Providing and fixing wooden rib false ceiling using 12mm thick BWR Plywood, finished with approved shade 3.5mm veneer with melamine polish. The false ceiling shall be provided combination with gypsum in different levels and the rate shall be inclusive of providing framework, adequate supports using 50mm x 25mm aluminium extrusions (both ways not more than 600mm c/c) with necessary countersunk heavy duty screws, hardware and adhesives etc; Teakwood edge beadings to be provided as directed.(Basic cost of veneer is Rs.850/Sqm)

od170865/2021_2022 : Perforated Wooden Slats - Melamine Laminated<br>Supply & installation of perforated wooden grooved slats ceiling - FR grade, Slats L16-2 - (2mm Slats @16mm pitch) of size 128mm x 2430mm x 16mm thick made out of wood particle, Melamine laminated finish, backlined with acoustical fleece, fixed by using GI channel of 0.5mm thk having 21mm & 27mm width, height 18mm, having flanges of 7mm (installed horizontally -for vertical fixing of slats) spaced at 400mm centers with suitable brackets, GI 18mm channel is perpendicularly to the GI cross sectional channel of 0.45mm thk having a knurled web of 50mm width, height 22mm, having flanges of 15mm is then fixed to the Main channel with the help of connecting clip in direction perpendicular to the Main Channel at every 600mm centers main Channels of web 45mm x 0.9mm thk with two flanges of 15mm each from the soffit at every 1000mm centers with suspender angle of size 25mm x10mm x 0.45mm thk fixed to the soffit with G.I Cleat and metal fasteners as indicated in the drawing. The system is backlined with the acoustical infill synthetic polyfibre 25mm thick (SynthPF 10x25)<br>The Perforated Wooden Slats ceiling module perimeter is covered with 12mm thick plywood with laminated finish, <br>color as per the choice of Client / Architect, with necessary supports as indicated in the drawing.Technical Parameters of the Perforated Wooden Slats - Melamine Laminated material <br>• Fire – Class A<br>• Acoustics –NRC 0.7<br>• Climate (OC, RH) – 50,70<br>• Termite resistance – Yes<br>• Light – 75 % <br>• Green – 25 %<br>• Hygience (VoC, Clean room) – Low, Class1<br>Rate inclusive of cost of all the materials, labour, scaffolding, installation and all taxes. Finished area of flooring shall be measured in Sqm for payment. Note - Vendor to submit valid test certificates for the above mentioned technical parameters. Approved manufacturer: Anutone, Armstrong, Top akustic /RPG

od170868/2021_2022 : Supply and fixing of Vox Infratop false ceiling manufactured in europe, of panel sizes of 340mmx 2700mm, durable and resistant to moisture, water and borer-fungus-termite attack. Panels to be installed with GI / Alumnium sections of suitable gauge & size according to site conditions .Panels SV 08/07 &09 with suitable trims SV 15 with dimensions 40x19x22x12x3050 (all in mm) for edge profiles and SV 18 with dimensions 67x3050 mm with T head of 42mm for Connecting profiles . Panels must be maintainance free , rust proof and are 100% Water proof . Advised especially for Soffit areas , under the roof installation . 10 years warranty for colour & finish of the panels and the profiles from VOX.

12.45.1 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum plain board conforming to IS : 2095-Part 1

od170876/2021_2022 : ACOUSTIC CLOUD CEILINGSupply and Installation of Anutone Clouds Hush, square edge, FR grade Hush fabric (colour choice) wrapped glassfibre core panel of size 600x1200x25mm having volume density 120Kgs/m3 and weight 3kg/m2. Each cloud is provided with 4 sets of accessories containing spring hooks, levelling clip and hanger wires. Springs to be rotated and anchored at back of each panel at four points to hold the panel stable. Supplied hanger wires to be first placed from the beam/slab/truss to desired height with suitable cleats/anchor bolts. Anutone Clouds Hush panels are then suspended using spring hooks and hanger wires and levelled into position with supplied levelling clips. (Cleats and anchor bolts not by Anutone)Technical Parameters • Fire (Class) – 1 & P• Acoustics – NRC 0.9• Thermal conductivity (W/mk)– 0.07• Climate (°C, RH) – 49, 90• Light reflectance (%) – Colour dependant• Green (VoC, RC %) – Low, 25

od170878/2021_2022 : WOODEN CEILING<br>Providing and fixing wooden false ceiling using 19mm BWR ply finished with  1.0 mm htick Laminate of approved make and color and with groove lines in pattern as per the instructions of the Architect. The wooden false ceiling shall be provided in combination with the gypsum boards in different levels and the The work shall be inclusive of providing framework, adequate supports using 50mm x 25mm aluminium extrusions (both ways 600mm c/c) with necessary countersunk heavy duty screws, hardware and adhesives etc; and polished teakwood edge beadings to be provided as directed.

od170881/2021_2022 : METAL LINEAR CEILING 300 C<br>Supplying & Installing Luxalon 300 C or equivalent Plain   aluminium metal False ceiling system manufactured by Hunter Douglas consists of panel of 300 mm wide x 30 mm deep with bevel edge manufactured out of 0.7 mm thick stove enamelled coil coated on continuous paint line aluminium Alloy AA3005/3003/3105 strips having panel length up to 3 mtrs.  The panel ends will be raised up to 29 mm. The panels about each other with a narrow ‘V’ groove. Panel shall be clipped to a baked enamelled Aluminium carrier of 41.5 mm wide x 62 mm deep x 0.95 mm thick in standard length of 5 mtrs, positioned at maximum 300 mm distance from both ends of the panels and in between at maximum distance of 1500 mm c/c. Panel carrier shall be fixed by means of M8 Rod/Bolt length not more than 250mm with nuts at 1200mm c/c to the suitable substructure provided by others at maximum at 1200mmm c/c.  The panel shall be stove enamelled coil coated in white or grey colour with thickness of 25 microns.<br>Panels: 300 mm wide x 30 mm deep with bevel edge manufactured out of 0.7 mm thick stove enamelled coil coated on continuous paint line aluminium Alloy AA 3005/3003/3105 strips  having panel length up to 3 mtrs. The panel ends will be raised up to 29 mm. The panels abut each other with a narrow ‘V’ groove<br>300 C Carrier: Aluminium carrier baked enamelled in black colour of 41.5 mm wide x 62 mm deep x 0.95 mm thick /0.5mm thick  GI in standard length of 5 mtrs.<br>Carrier Splice: Aluminium panel carrier  splice shall be used to join two carriers to continue.<br>Threaded Rod:   M8 threaded rod Used to fix or suspend the carrier from the slab/steel sub structure provided by others. <br>Edge Profile:  Aluminium 0.7mm thick edge profile of 23mm x23mm shall be used to  terminate ceilings at Perimeter in matching colour of panel.

od170883/2021_2022 : MINERAL FIBRE TILE CEILING<br>Providing and fixing in true horizontal level false ceiling of silhouette grid system with 15mm white flanges incorporating a 6mm central reveal in white/black colour of approved make using hot dipped galvanized steel section, exposed surface chemically cleaned capping pre-finished in baked polyester paint wall angle of size 3000mmx19mmx19mm used in the periphery of the ceiling fixed to the wall partition / RC Column / band walls with the help of screws at 600mm C/C. Main runner spaced at a 1200mm C/C suspended by using 2mm dia G.I. wire hanger securely fixed to the structural soffit of RC slab by using 6mm anchor fastener at every 1200mm(max) and 1200mm long cross tee to be interlocked between in Main runner at 600mm C/C (max) to form a grid of 1200mmx600mm. 600mm long cross tee fixed in between 1200mm long cross tee for forming a grid of 600mmx 600mm. The rate shall be including the cost of grid system and the cost of necessary hardwares like anchor fasteners, spring steel clips, suspension rods, GI wire hangers, screws, bolt and nuts etc; Providing and laying 19mm thick, 600x600mm size Ultima/approved equivalent mineral fibre acoustic ceiling tiles with micro look edge, 60minutes fire rating as per BS 476/23 of 1987, Noise Reduction Co-efficient (NRC) of 0.70, Light Reflectance of 83%, Sound Attenuation of 30 dB, Thermal Conductivity K=0.052 W/m°K, Humidity Resistance of RH-95%. The rate shall be inclusive of wastages etc; complete.

PARTITION WORKS

od170848/2021_2022 : Gypsum partition: 122mm thick GI stud partition which includes double layer of 12.5mm thick Gypsum Board consists of tapered edge & dense Gypsum core further contributes to “Severe Duty Rating” for partition as per BS 5234 Part 2) of size 1220x2440mm is screw fixed to C-stud. 70 x 34 x 36 x 0.5mm C-stud (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513) placed at 610mm c/c in 72 x 32 x 32 x 0.5mm floor and ceiling channel (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513). Floor & Ceiling channel is anchored to the floor & True ceiling using Rawl plug (Anchor Fastener) Ø8x45mm {Material-IS 513 CR1 grade, Zinc coating, Pull Out Load-6.8kN for M30 concrete grade} at 600mm c/c in zigzag manner.Floor channel to be wrapped with 70μ Self Adhesive LDPE moisture barrier film to further improve corrosion resistance performance. 12.5mm thick Gypsum Board consists of tapered edge & dense Gypsum core which further contributes to “Severe Duty Rating” for partition as per BS 5234 Part 2) strip of 72 mm width is placed between ceiling channel and RCC ceiling slab when deflection is more than 10mm & fire rating is more than 30min. A Noggin channel of size 70 x 40 x 40 x 0.5mm (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513) has to be provided at the horizontal joints of the two boards.Gypsum board to be screw fixed with Drywall screws of 25mm at minimum spacing of 300mm at center and 150mm at periphery. 50mm Glass wool slab of density 20kg/m³ shall be placed in metal framework. Glass wool holding clip should be used to hold Glass wool slab in its position. Finally, square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Gypsum Jointing compound, (Conforms to ASTM C475) and Joint Paper tape. The junction of the partition with masonry & all penetration through the partition has to be treated with Hilti/Pyroplex fire and acoustic sealant. All the above-mentioned technical parameters will be approved based on third party certification from the manufacturer. TYPE A Same as above with Framework and insulation but sides finished with both side 18m BWR ply for up to false ceiling areas. The item shall include cutting the boards as necessary for all services crossings and filling the gaps if any as necessary.

od170861/2021_2022 : Gypsum partition: <br>122mm thick GI stud partition which includes double layer of 12.5mm thick Gypsum Board consists of tapered edge & dense Gypsum core further contributes to “Severe Duty Rating” for partition as per BS 5234 Part 2) of size 1220x2440mm is screw fixed to C-stud. 70 x 34 x 36 x 0.5mm C-stud (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513) placed at 610mm c/c in 72 x 32 x 32 x 0.5mm floor and ceiling channel (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513). Floor & Ceiling channel is anchored to the floor & True ceiling using Rawl plug (Anchor Fastener) Ø8x45mm {Material-IS 513 CR1 grade, Zinc coating, Pull Out Load-6.8kN for M30 concrete grade} at 600mm c/c in zigzag manner.Floor channel to be wrapped with 70μ Self Adhesive LDPE moisture barrier film to further improve corrosion resistance performance. 12.5mm thick Gypsum Board consists of tapered edge & dense Gypsum core which further contributes to “Severe Duty Rating” for partition as per BS 5234 Part 2) strip of 72 mm width is placed between ceiling channel and RCC ceiling slab when deflection is more than 10mm & fire rating is more than 30min. A Noggin channel of size 70 x 40 x 40 x 0.5mm (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513) has to be provided at the horizontal joints of the two boards.Gypsum board to be screw fixed with Drywall screws of 25mm at minimum spacing of 300mm at center and 150mm at periphery. 50mm Glass wool slab of density 20kg/m³ shall be placed in metal framework. Glass wool holding clip should be used to hold Glass wool slab in its position. Finally, square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Gypsum Jointing compound, (Conforms to ASTM C475) and Joint Paper tape. The junction of the partition with masonry & all penetration through the partition has to be treated with Hilti/Pyroplex fire and acoustic sealant. All the above-mentioned technical parameters will be approved based on third party certification from the manufacturer.

od170863/2021_2022 : Gypsum partition: <br>122mm thick GI stud partition which includes double layer of 12.5mm thick Gypsum Board consists of tapered edge & dense Gypsum core further contributes to “Severe Duty Rating” for partition as per BS 5234 Part 2) of size 1220x2440mm is screw fixed to C-stud. 70 x 34 x 36 x 0.5mm C-stud (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513) placed at 610mm c/c in 72 x 32 x 32 x 0.5mm floor and ceiling channel (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513). Floor & Ceiling channel is anchored to the floor & True ceiling using Rawl plug (Anchor Fastener) Ø8x45mm {Material-IS 513 CR1 grade, Zinc coating, Pull Out Load-6.8kN for M30 concrete grade} at 600mm c/c in zigzag manner.Floor channel to be wrapped with 70μ Self Adhesive LDPE moisture barrier film to further improve corrosion resistance performance. 12.5mm thick Gypsum Board consists of tapered edge & dense Gypsum core which further contributes to “Severe Duty Rating” for partition as per BS 5234 Part 2) strip of 72 mm width is placed between ceiling channel and RCC ceiling slab when deflection is more than 10mm & fire rating is more than 30min. A Noggin channel of size 70 x 40 x 40 x 0.5mm (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513) has to be provided at the horizontal joints of the two boards.Gypsum board to be screw fixed with Drywall screws of 25mm at minimum spacing of 300mm at center and 150mm at periphery. 50mm Glass wool slab of density 20kg/m³ shall be placed in metal framework. Glass wool holding clip should be used to hold Glass wool slab in its position. Finally, square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Gypsum Jointing compound, (Conforms to ASTM C475) and Joint Paper tape. The junction of the partition with masonry & all penetration through the partition has to be treated with Hilti/Pyroplex fire and acoustic sealant. All the above-mentioned technical parameters will be approved based on third party certification from the manufacturer.<br>Specification same but single layer of gypsum at above falseceling level

od170869/2021_2022 : Gypsum partition: <br>122mm thick GI stud partition which includes double layer of 12.5mm thick Gypsum Board consists of tapered edge & dense Gypsum core further contributes to “Severe Duty Rating” for partition as per BS 5234 Part 2) of size 1220x2440mm is screw fixed to C-stud. 70 x 34 x 36 x 0.5mm C-stud (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513) placed at 610mm c/c in 72 x 32 x 32 x 0.5mm floor and ceiling channel (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513). Floor & Ceiling channel is anchored to the floor & True ceiling using Rawl plug (Anchor Fastener) Ø8x45mm {Material-IS 513 CR1 grade, Zinc coating, Pull Out Load-6.8kN for M30 concrete grade} at 600mm c/c in zigzag manner.Floor channel to be wrapped with 70μ Self Adhesive LDPE moisture barrier film to further improve corrosion resistance performance. 12.5mm thick Gypsum Board consists of tapered edge & dense Gypsum core which further contributes to “Severe Duty Rating” for partition as per BS 5234 Part 2) strip of 72 mm width is placed between ceiling channel and RCC ceiling slab when deflection is more than 10mm & fire rating is more than 30min. A Noggin channel of size 70 x 40 x 40 x 0.5mm (with superior and complete serrated surface confirming to AZ150 as per IS 15961 and yield strength of 300Mpa confirming to IS 513) has to be provided at the horizontal joints of the two boards.Gypsum board to be screw fixed with Drywall screws of 25mm at minimum spacing of 300mm at center and 150mm at periphery. 50mm Glass wool slab of density 20kg/m³ shall be placed in metal framework. Glass wool holding clip should be used to hold Glass wool slab in its position. Finally, square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Gypsum Jointing compound, (Conforms to ASTM C475) and Joint Paper tape. The junction of the partition with masonry & all penetration through the partition has to be treated with Hilti/Pyroplex fire and acoustic sealant. All the above-mentioned technical parameters will be approved based on third party certification from the manufacturer.<br>TYPE C,D & E Same as above with Frame work and insulation but sides finished with One side 18mm BWR ply & other side Gyp board for upto false ceiling areas. The item shall include cutting the boards as necessary for all services crossings and filling the gaps if any as necessary.

od170872/2021_2022 : Partition above false ceiling level, closing by Calcium silicate board with frame work.<br>Providing and fixing Partition above the false ceiling level using Aluminium box frames of size 50mmx25mmx1.5mm thickness at 610mmc/c on both directions and to be covered with 9mm thick single layer Calcium silicate board on both sides. The joints are to be finished with jointing compound as per manufacturers specification. The boards shall be fixed with counter sunk stainless steel / fully threaded self tapping screws of suitable dia and length at every 300 mm c/c. Note: The framework shall be anchored/ fixed properly in true RCC ceiling, to get sufficient rigid both side aluminium 'Y' type support.

od170874/2021_2022 : Straight Glazed Partition-Slim line of approved make: Providing and installation of full height straight glass partition from FFL to the bottom of false ceiling and fixing 12mm thick toughened and heat soaked glass and proprietary type anodized aluminium slimline sections of approved make. The sections shall be matt finish natural anodized and shall be a combination of male and female frames on all four sides as per the manufacturers specification. The rate shall be including the cost of all necessary hardwares, anodized aluminium jointing profile on edges of the glass in parallel glass joints, and anodized aluminium corner profile in corner glass joints including the cost of 12mm thick toughened and heat soaked glass.

JOINERIES

od170857/2021_2022 : Supply & Fixing of Glass Door (Single Leaf) of 12mm toughened glass with Hafele/ Dorma make  fittings  and  wideline frames  all around the glass and shutter .The  profiles shall be suitable for Glass thickness of  12 mm.The Profile shall be matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system.All Profiles to be with 2 mm Gauge thickness Excluding 20 Micron of Anodizing.Single leaf door of size 1100 x 2100mm necessary Hafele make hardwares as mentioned in the drawings

od170858/2021_2022 : ACOUSTIC DOOR: Supply and Installation of noise and fire rated Acoustical door (thickness – 75mm including 1mm Thick Laminate of suede finish on both faces of the shutter.SIGNATURE MAKE 120mins.Fire Rated Acoustic Timber door with Timber frame.<br>DOOR FRAMES <br>The door frame profile is 175x 75mm of triple rebate construction is made from Hardwood. The Door frame shall be Painted matching to the Laminate. Frames are rigidly bolted at top jamb for direct installation at site. The door frame is fixed by adequate number of anchor fasteners on vertical and top jamb. <br>SHUTTERS The timber fire door shutters are constructed out of sandwiched non combustible boards. Fully flush double skin door have treated hardwood bidding on all four edges. Shutters have no visible screws or fasteners on either face. The door construction is of proprietary design incorporating fire retardant, heat insulating material suitable for fire stability integrity and insulation rating for 120 minutes. The construction is totally asbestos free. Shutters have intumescent strip on three edges except the bottom. Shutters are fabricated with pre punched cut outs and reinforcements to receive ironmongery. Two hours rated acoustic timber shutters are 75mm thick. Treated water proof ply of 6mm thickness encloses the entire door assembly on both faces. <br>Shutters shall be finished with 1mm Thick Laminate of suede finish on both faces of the shutter.SOUND PROOFING<br>Signature’s Timber Door’s sound attenuation properties are achieved through the use of high-accuracy foil with small metal globules enclosed in its honeycombs. In combination with the proprietary hard wood skeleton structure and non combustible building board, a very good sound proof factor can be achieved. Door size : 1000 x 2100 mm

WALL ACCOUSTIC PANELS

od170850/2021_2022 : Wall panelling with Wooden screen finish:Anutone Slats Surco Plus, 128 x2440x16mm, T&G edge:Supply & installation of Anutone Salon Slats Surco made of pinewood E1 grade fiberboard, melamine/veneer laminated finish, groove perforated slats L8-2 - (2mm grooves @ 8mm centers with 52% open area) / L16-2 - (2mm grooves @16mm pitch with 27% open area) / L32-2 - (2mm grooves @ 32mm centers with 15% open area) / L64-2 - (2mm grooves @ 64mm centers with 8% open area), backlined with Soundtexblack acoustical fleece of 0.27mm thick, surface density 63g/m2,tongue-groove edge for a seamless look, 5-test fire retardant grade, size 128 x2440x16mm, volume density of base board 700Kg/m3, weight 9Kg/m2 (L16), 10.5Kg/m2 (L32), 11Kg/m2 (L64) installed by using Anutone Strut framework system.The Anutone Strut framework system shall include Anutone Strut CC25, fully knurled, sectional thickness 0.55mm, length 3600mm, web 50mm, depth of 25mm and equal flanges 15mm is fastened to the wall positioned horizontally/vertically at every 600mm centres.<br>Anutone Strut CC18,aluminium core cross channel, thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & center brackets is then fixed perpendicular to the Strut CC25 with the help of fasteners at every 400mm centers<br>Anutone Slats Surco Plus of size 128x 2440x16mm in then fixed perpendicular to Strut CC18 with suitable edge & centre brackets. <br>Contractor to provide expansion joints of 3mm at every 4.88m length wise and 4.992m width wise.The system is backlined with Anutone SynthPF 10x25 adhered on wall with dab spots of Anutone stick S7 adhesive.Technical Parameters -• Fire (Class) – 1 & P <br>• Acoustics – NRC 0.75( For L32 C40 Mounting)<br>• Thermal conductivity (W/mk)– na<br>• Climate (°C, RH) – 50, 70<br>• Light reflectance (%) – 75 (Maple Arce)<br>• Green (VOC, RC %) – E1, 25

od170859/2021_2022 : Providing and fixing of 3.5mm thick veneer of approved color and shade with grooves and lines and in patterns as instructed by Architect / Client.and finished with melamine polish up to required level to the item nos.2a,2b, below. The rate to be include the cost of necessary hardwares, adhesives, wastages etc; as required for complete the works. Base cost of 3.5mm veneer is Rs.700/sqm. Actual seen surface only will be measured and paid.

od170864/2021_2022 : WOODEN WALL AND COLUMN PANELLING WITH INSULATION<br>Providing and fixing column /WALL panelling as shown in drawing no. but in general, it shall be made out of aluminium box frame of size 50 x 25 mm - 1.5mm tk at 600mm c/c in both direction. covered with 10 mm thick BWR ply and finished with 1.5 mm thick Laminte of approved shade. including forming pattern and details as in drg. Rate shall include for providing teak wood beadings edge protection and as directed complete with necessary hardwares. Rate shall include for forming a panelling to any shape including circular profile etc. complete.) Rate include 50mm thick rockwool insulation with 48kg/cum<br>50mm Rockwool insulation 48kg/cm covered with acoustic wooden slats

od174477/2021_2022 : Wide line Door Frames of approved make : Supplying, receiving, unloading, storing and installation of proprietary type wide line door frames (25mm depth) of approved make using proprietary designed hinges. The section shall be matt natural anodized as per manufacturer's specification and the cost shall be including the cost of all necessary hardware.

MISCELLANEOUS

od170853/2021_2022 : Dismantling of Reinforced Cement Concrete work in any concrete memeber of any size & shape, at all levels, removal of debris, disposing the same away from the site, loading and unloading, making the surface good etc. complete. Rate shall include for disposing the unserviceable materials/debris away from the site by mechanical means including loading, unloading, clearing the site etc. complete, as directed.

od170862/2021_2022 : Dismantling of Cement Concrete block masonary work of any size & shape, at all levels, removal of debris, disposing the same away from the site, loading and unloading, making the surface good etc. complete. Rate shall include for disposing the unserviceable materials/debris away from the site by mechanical means including loading, unloading, clearing the site etc. complete, as directed.

od170875/2021_2022 : Providing and fixing in position of Aluminium sliding window using suitable sections for three track system, Interlocking frame with 5mm thick float glass with all accessories and finished the surface neat etc complete as directed by Engineer In charge

od170879/2021_2022 : Providing and fixing of Anodized or Powder coated Global make aluminium fixed windows by using 63.50 x 38.1 x 2mm thick box sections for outer frame and mullions, with glazing clips and EPDM Gaskets including 5mm thick clear float glass complete

od170880/2021_2022 : Providing and fixing Wall panelling Wooden screen board as per direction of Engineer in charge.

od170882/2021_2022 : Providing dadoing with best quality approved make Brick tiles of approved size set in C.M.1:3 and white cement slurry with approved joint filler grout compound, all as per manufacturer's specification, at all levels and as directed. Rate shall include for preparation of plastered surface, smooth joint, cleaning etc. complete and as directed.

od170884/2021_2022 : Providing and fixing of Floor storage of size 450mm width and 750mm height as per drg it shall be fitted into wall with necessary hardware's etc. The top, bottom, back and intermediate shelf having 19mm thick BWR plywood. All the exposed ply wood surfaces shall be finished with 1.5mm thick, century make laminates of Accasua / Larrido pine and the internal surfaces are finished with 1mm thick century make approved colour plain laminates. The rate should be includes louver shutters,the cost of Hafele Equivalent make hardware's like cabinet hinges of approved make, ball catches etc.

od170886/2021_2022 : Supplying and installation of Reception table made to shape and pattern identical as per drawing and to a height of two levels 1100 mm and 750mm , but in general it shall be made of 19mm thick BWR plywood as table top, sides, front and rear side with adequate supports as directed in both horizontal and vertical directions. Providing 2nos of drawer unit with a pencil drawer, and storage with openable shutters and one intermediate shelf at both sides of the table and middle providing open storage to accomodate printer. providing 2 nos key board tray at the specified location using BWR plywood 12mm thick etc. complete. All exposed ply wood surfaces except the skirting and front and sides of the table shall be finished with 1 mm thick approved shade and make laminates and internal surfaces shall be of sealer finish. The rate is also includes the cost of necessary hardware's, sliding runners, handles, auto closing hinges, locks with one master key for two drawers, teakwood lipping/moulding, foot rest with PU polish finish. The necessary provison like making holes in ply wood for fixing cable pipes and switch boxes is to be included.

od170887/2021_2022 : Providing and fixing of 8mm thick lacquared glass write on board backing with 12mm thick BWR ply both side finished with two coats enamel paint of approved shade over a coat of primer. Edges covered with 50mmx50mm teak wood decorative beading finished with melamine matt polish of required level. The rate shall be inclusive hardware, lead and lift etc.

od170888/2021_2022 : Supplying and fixing Pull down Projector screen with remote operation of approved make

od170889/2021_2022 : Supplying and fixing ONYX wall cladding with necessary back supports as per manufacturer specifications

od170890/2021_2022 : EMULSION PAINT<br>Providing two coats of first quality Acrylic emulsion paint of approved make and colour over a priming coat of white colour paint or any primer specified by the manufacturer including preparation of surface by thorough cleaning and wetting before painting and all as per manufacturer's specifications and as directed.

od170891/2021_2022 : Providing and fixing wall cladding Kalinga wall panels Engineered Marble Slabs / Engineered terrazo slabs as per approved shade with all necessary base panel work with aluminum wall supports and 12 mm thick BWR ply as per manufacturer's Specification and as directed. The Rate includes installation cost with adhesive.Basic rate Rs.300/Sqm+C94:C95<br>

od170892/2021_2022 : Providing and fixing white matt finish white mark writing board of enamelled sheet steel front, GI back over approved inner core, of specified size black or chocolate colour wooden beading with polish finish to form the screen including the necessary accessories such as magnetic symbols, magnetic letters, magnetic strips, magnetic eraser, magnetic dry marker 4nos spare felt for eraser, board fixing clips etc. and the board shall be made out of enamelled sheet with backing of AC sheet to suitable thickness etc. complete and all as per manufacturer's specification and as directed by the Employer / Architect. Rate shall inclusive of making and fixing wooden ledge for full length of the board for keeping marker pen, eraser etc. Rate quoted shall be for the complete finished work including ledgeboard to keep accesories , and all materials and labour mentioned above.

od170893/2021_2022 : Providing and fixing of 3M frosted film of approved color as per required pattern and shape and as directed. The vendor shall submit required warranty certificates from the manufacture. (Basic cost Rs.1200/Sqm)

od170894/2021_2022 : Texture paint of approved colour on existing gyspum surface / wall surface from asian paints/ nerolac or oikos (Basic cost Rs.500/sqm)

od170895/2021_2022 : Wall paper : SUPPLY & installation of wall paper on existing wall/partition, after punny, painting with primer coat and curing of the surface to ensure propoer levelling and surface treatment prior to fixing of wall paper., inclusive of wastage. Basic cost Rs.110/sft<br>

od170896/2021_2022 : Providing and fixing soft board panel of specified sizes having 12mm thick soft board with a 8mm thick BWR plywood backing and softboard covered with fabric of approved make and shade of premium quality and cost of fabric not less than Rs.300/1meter ht.1200mm). The board shall have a teakwood / cedar / beech / matching wooden beading, lipping around. The board shall be fixed with hook on system on the existing panelling or wall prepared surface with necessary hardware fittings etc. complete. All wood works shall have sealer polish as directed. Rate quoted shall be for the complete finished work including all the materials and labour mentioned above.<br>

od170897/2021_2022 : Providing and fixing of Anodized aluminium extruded skirting of 1mm Thick polished finish as per approved make or equivalent make to a height of 100mm. Rate shall be inclusive of fixing as per manufacturer specification and the fixing screws should not be visible.

od174091/2021_2022 : Providing and applying white cement based putty (two coats) of approved brand & manufacturer over plastered / Gypsum Surface to prepare the surface even and smooth complete.

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

17.10.2.1 : Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink without drain board610x510 mm bowl depth 200 mm

8.2.2.1 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shadeArea of slab upto 0.50 sqm

18.8.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal outer dia pipes

18.8.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.32 mm nominal outer dia pipes

18.9.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work25 mm nominal outer dia pipes

18.9.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work32 mm nominal outer dia pipes

18.9.6 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work50 mm nominal outer dia pipes

18.18.3 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:25 mm nominal bore

17.28.1.1 : Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. waste fittings complete.Semi rigid pipe32 mm dia

od174389/2021_2022 : Providing, fixing and testing UPVC Class-3 pressure rating 6 kg /sqcm pipe of approved Make for underground drainage and sewerage systems - Confirming to IS 4985:2000 and speciels such as such as coupler, elbow, bends and Tee,etc This includes jointing of pipes &fittings with solvent cement and cost of cutting chases and making good the same include testing of joints for suspended lines and work in below ground. Woks includes necessary scaffolding, cutting and making good the walls wherever required ,complete as per direction of Engineer in charge. 50 mm dia.

od174390/2021_2022 : Providing, fixing and testing UPVC Class-3 pressure rating 6 kg /sqcm pipe of approved Make for underground drainage and sewerage systems - Confirming to IS 4985:2000 and speciels such as such as coupler, elbow, bends and Tee,etc This includes jointing of pipes &fittings with solvent cement and cost of cutting chases and making good the same include testing of joints for suspended lines and work in below ground. Woks includes necessary scaffolding,cutting and making good the walls wherever required ,complete as per direction of Engineer in charge. 40 MM Dia

5.2.2 : Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.9.20 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

Electrical

od59172/2021_2022 : 12 WAY SPN DB :<br>Supply, fixing, testing and commissioning of the double door type compartmental MCB DB comprising of the following :<br>25A, DP, 30mA RCBO – 1 No. as incomer (Type-Compact) .<br>Outgoing consist of 8 nos. 6/10A SP MCB (C-Curve) with necessary accessories as required.<br>With necessary tinned copper busbars, interconnections, separate earth bus, separate neutral bus for each phases. The board shall be powder coated type fixed with concealed system in wall/fixed in column. The rate shall include necessary connected civil works like chipping and plastering etc. <br>

od59195/2021_2022 : 4 WAY SEVEN SEG. DB :<br>Supply, fixing, testing and commissioning of the double door type compartmental MCB DB comprising of the following :<br>25A TPN MCB – 1 No. as incomer.<br>25A DP RCBO C-Curve 30mA – 3 Nos. as outgoings.<br>Each Phase 25A DP RCBO outgoing consist of 4 nos. 6/10A SP MCB (C-Curve) with necessary phase segregation as required.<br>With necessary tinned copper busbars, interconnections, separate earth bus, separate neutral bus for each phases. The board shall be powder coated type fixed with concealed system in wall/fixed in column. The rate shall include necessary connected civil works like chipping and plastering etc. <br>

od59231/2021_2022 : 4 WAY SEVEN SEG.DB :<br>Supply, fixing, testing and commissioning of the double door type compartmental MCB DB as per SLD comprising of the following :<br>40 A TPN MCB – 1 No. as incomer.<br>40 A DP RCBO C-Curve 100mA – 3 Nos. as outgoings.<br>Each 40 A DP RCBO outgoing consist of 4 nos. 16/20 A SP MCB (C-Curve) in a separate compartment with necessary accessories as required.<br>With necessary tinned copper busbars, interconnections, separate earth bus, separate neutral bus for each phases. The board shall be powder coated type fixed with concealed system in wall/fixed in column. The rate shall include necessary connected civil works like chipping and plastering etc. <br>

od60236/2021_2022 : 6 WAY SEVEN SEG. DB :<br>Supply, fixing, testing and commissioning of the double door type compartmental MCB DB as per SLD comprising of the following :<br>63A TPN MCB – 1 No. as incomer.<br>63A DP RCBO C-Curve 30mA – 3 Nos. as outgoings.<br>Each 63 A DP RCBO outgoing consist of 6 nos. 16/20 A SP MCB (C-Curve) in a separate compartment with necessary accessories as required.<br>With necessary tinned copper busbars, interconnections, separate earth bus, separate neutral bus for each phases. The board shall be powder coated type fixed with concealed system in wall/fixed in column. The rate shall include necessary connected civil works like chipping and plastering etc. <br>

od60281/2021_2022 : 4WAY (Vertical TPN) MCCB DB <br>Supply, fixing, testing and commissioning of the double door type VTPN 4 way MCCB DB comprising of the following :<br>32 A TPN MCCB 16 KA – 1No. Incomer<br>10A TP MCB – 4 Nos. as outgoings.<br>With necessary tinned copper busbars, interconnections, earth bus, neutral bus. The board shall be powder coated type fixed with concealed system in wall/ fixed in column. The rate shall include necessary connected civil works like chipping, rough plastering etc. <br>

od60323/2021_2022 : 6 WAY SEVEN SEG. UPS DB <br>Supply, fixing, testing and commissioning of the double door type compartmental MCB DB comprising of the following :<br>32 A TP+2N MCB – 1 No. as incomer.<br>32A SP+2N RCBO 30mA (hi/hpi/si) – 3 Nos. as outgoings.<br>Each 32 A SP+2N RCBO outgoing consist of 6nos. 10 A SP MCB (D-Curve) in a separate compartment with necessary phase segregation as required by the Electrical Inspectorate.<br>With necessary tinned copper busbars, interconnections, separate earth bus, separate neutral bus for each phases. The board shall be powder coated type fixed with concealed system in wall/fixed in column. The rate shall include necessary connected civil works like chipping and plastering etc. <br>

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.4 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.40 mm

5.19 : Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

od60877/2021_2022 : GROUNDING ,EARTHING SYSTEM<br>10 SWG Cu. Wire for Gland earthing<br>

1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.17.12 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.17.21 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm

od62642/2021_2022 : Supply, Installation, testing and commissioning of 1 no 6/16A universal switched socket and with moulded front plate GI anodised enclosure in the wall/floor(concealed/open and other associated accessories including chasing embedding rough plastering as required as per the site conditions for power points.

od62643/2021_2022 : Supply, Installation, testing and commissioning of 2nos 6A Universal switched socket ( UPS) and 2nos 6A switches and with moulded front plate, GI anodised enclosure, and mounting box in the wall(concealed/open)and other associated accessories including chasing embedding rough plastering as required as per the site conditions for power points.

od62644/2021_2022 : Supply, Installation, testing and commissioning of 1 no 6A Universal switched socket and with moulded front plate, GI anodised enclosure, and mounting box in the wall(concealed/open)and other associated accessories including chasing embedding rough plastering as required as per the site conditions for power points.

od62658/2021_2022 : Supply, fixing, testing and commissioning of POP UP Box (8M) on table / floor with suitable Flush-mounting boxes suitable for 2Nos of 6/10A 240V universal socket controlled by 2nos of 6A switch individual and 1No. of 6/10A 240V universal socket controlled by 1 No. of 10A switch for installation in table top / concrete floors, Colour shall be Brushed stainless steel finish and suitable metal back box, necessary earthing terminals provided at the back box and all other required accessories..<br>

od62664/2021_2022 : "LT CABLES <br>Supply, Laying, Testing and Commissioning of following 1100V XLPE A2XFY (XLPE insulated Armoured Aluminium) / YFY (Armoured Copper) / YY (Unarmored/Flexible Copper) cables laid over MS supports / Cable racks / in excavated Trench / fixing of walls including clamping the cable to the support in all approved manner as all complete required (Note : Inclusive of supply of Anchor Fasteners, straight through joints and necessary 1.5mm thick GI Flat, clamps shall be included in the laying cost). "<br>3.5C 35 Sq.mm. A2XFY - XLPE <br>

od62665/2021_2022 : "LT CABLES <br>Supply, Laying, Testing and Commissioning of following 1100V XLPE A2XFY (XLPE insulated Armoured Aluminium) / YFY (Armoured Copper) / YY (Unarmored/Flexible Copper) cables laid over MS supports / Cable racks / in excavated Trench / fixing of walls including clamping the cable to the support in all approved manner as all complete required (Note : Inclusive of supply of Anchor Fasteners, straight through joints and necessary 1.5mm thick GI Flat, clamps shall be included in the laying cost). "<br>4C 25 Sq.mm. A2XFY - XLPE for PANELS,<br>

od62666/2021_2022 : "LT CABLES <br>Supply, Laying, Testing and Commissioning of following 1100V XLPE A2XFY (XLPE insulated Armoured Aluminium) / YFY (Armoured Copper) / YY (Unarmored/Flexible Copper) cables laid over MS supports / Cable racks / in excavated Trench / fixing of walls including clamping the cable to the support in all approved manner as all complete required (Note : Inclusive of supply of Anchor Fasteners, straight through joints and necessary 1.5mm thick GI Flat, clamps shall be included in the laying cost). "<br>4C 16 Sq.mm. A2XFY - XLPE for ,PDBs etc<br>

od62667/2021_2022 : "LT CABLES <br>Supply, Laying, Testing and Commissioning of following 1100V XLPE A2XFY (XLPE insulated Armoured Aluminium) / YFY (Armoured Copper) / YY (Unarmored/Flexible Copper) cables laid over MS supports / Cable racks / in excavated Trench / fixing of walls including clamping the cable to the support in all approved manner as all complete required (Note : Inclusive of supply of Anchor Fasteners, straight through joints and necessary 1.5mm thick GI Flat, clamps shall be included in the laying cost). "<br>4C 10 Sq.mm. XLPE cu. Ar. Cable for Extract fans,,LDBs,AHUs etc<br>

od62668/2021_2022 : "LT CABLES <br>Supply, Laying, Testing and Commissioning of following 1100V XLPE A2XFY (XLPE insulated Armoured Aluminium) / YFY (Armoured Copper) / YY (Unarmored/Flexible Copper) cables laid over MS supports / Cable racks / in excavated Trench / fixing of walls including clamping the cable to the support in all approved manner as all complete required (Note : Inclusive of supply of Anchor Fasteners, straight through joints and necessary 1.5mm thick GI Flat, clamps shall be included in the laying cost). "<br>4C 6 Sq.mm. XLPE cu. Ar. Cable for Extract fans,PDBs,LDBs,AHUs etc<br>

od62669/2021_2022 : "LT CABLES <br>Supply, Laying, Testing and Commissioning of following 1100V XLPE A2XFY (XLPE insulated Armoured Aluminium) / YFY (Armoured Copper) / YY (Unarmored/Flexible Copper) cables laid over MS supports / Cable racks / in excavated Trench / fixing of walls including clamping the cable to the support in all approved manner as all complete required (Note : Inclusive of supply of Anchor Fasteners, straight through joints and necessary 1.5mm thick GI Flat, clamps shall be included in the laying cost). "<br>4Cx4 sq.mm PVC Cu. Cables <br>

od62670/2021_2022 : "LT CABLES <br>Supply, Laying, Testing and Commissioning of following 1100V XLPE A2XFY (XLPE insulated Armoured Aluminium) / YFY (Armoured Copper) / YY (Unarmored/Flexible Copper) cables laid over MS supports / Cable racks / in excavated Trench / fixing of walls including clamping the cable to the support in all approved manner as all complete required (Note : Inclusive of supply of Anchor Fasteners, straight through joints and necessary 1.5mm thick GI Flat, clamps shall be included in the laying cost). "<br>1C 25 Sq.mm. XLPE cu. FL. Cable <br>

od62671/2021_2022 : "LT CABLES <br>Supply, Laying, Testing and Commissioning of following 1100V XLPE A2XFY (XLPE insulated Armoured Aluminium) / YFY (Armoured Copper) / YY (Unarmored/Flexible Copper) cables laid over MS supports / Cable racks / in excavated Trench / fixing of walls including clamping the cable to the support in all approved manner as all complete required (Note : Inclusive of supply of Anchor Fasteners, straight through joints and necessary 1.5mm thick GI Flat, clamps shall be included in the laying cost). "<br>1C 6 Sq.mm. XLPE cu. FL. Cable <br>

od62672/2021_2022 : "LT CABLE TERMINATION<br>Supply erection, Termination of PVC insulated armoured / unarmoured cables up to 1100V grade and connection of leads including the supply of Aluminum/COPPER cable lugs but including cutting stripping of cable insulation, providing double compression type glands, terminals, and armour earthing ,crimping the lug on to the conductor, clamping of the cable-cores, marking with wire number ferrules, etc.with Gland hood to be provided at the cable end entering to the Main panel and including all labour and materials complete and as per specifications of this tender and directions of Engineer-in-charge. End Termination of Cable using jointing kits & accessories as recommended by cable/ kit manufacturer."<br>3.5C 35 Sq.mm. A2XFY - XLPE <br>

od62673/2021_2022 : "LT CABLE TERMINATION<br>Supply erection, Termination of PVC insulated armoured / unarmoured cables up to 1100V grade and connection of leads including the supply of Aluminum/COPPER cable lugs but including cutting stripping of cable insulation, providing double compression type glands, terminals, and armour earthing ,crimping the lug on to the conductor, clamping of the cable-cores, marking with wire number ferrules, etc.with Gland hood to be provided at the cable end entering to the Main panel and including all labour and materials complete and as per specifications of this tender and directions of Engineer-in-charge. End Termination of Cable using jointing kits & accessories as recommended by cable/ kit manufacturer."<br>4C 25 Sq.mm. A2XFY - XLPE for PANELS,

od62674/2021_2022 : "LT CABLE TERMINATION<br>Supply erection, Termination of PVC insulated armoured / unarmoured cables up to 1100V grade and connection of leads including the supply of Aluminum/COPPER cable lugs but including cutting stripping of cable insulation, providing double compression type glands, terminals, and armour earthing ,crimping the lug on to the conductor, clamping of the cable-cores, marking with wire number ferrules, etc.with Gland hood to be provided at the cable end entering to the Main panel and including all labour and materials complete and as per specifications of this tender and directions of Engineer-in-charge. End Termination of Cable using jointing kits & accessories as recommended by cable/ kit manufacturer."<br>4C 16 Sq.mm. A2XFY - XLPE for ,PDBs etc<br>

od62677/2021_2022 : "LT CABLE TERMINATION<br>Supply erection, Termination of PVC insulated armoured / unarmoured cables up to 1100V grade and connection of leads including the supply of Aluminum/COPPER cable lugs but including cutting stripping of cable insulation, providing double compression type glands, terminals, and armour earthing ,crimping the lug on to the conductor, clamping of the cable-cores, marking with wire number ferrules, etc.with Gland hood to be provided at the cable end entering to the Main panel and including all labour and materials complete and as per specifications of this tender and directions of Engineer-in-charge. End Termination of Cable using jointing kits & accessories as recommended by cable/ kit manufacturer."<br>4C 10 Sq.mm. XLPE cu. Ar. Cable for Extract fans,,LDBs,AHUs etc<br>

od62678/2021_2022 : "LT CABLE TERMINATION<br>Supply erection, Termination of PVC insulated armoured / unarmoured cables up to 1100V grade and connection of leads including the supply of Aluminum/COPPER cable lugs but including cutting stripping of cable insulation, providing double compression type glands, terminals, and armour earthing ,crimping the lug on to the conductor, clamping of the cable-cores, marking with wire number ferrules, etc.with Gland hood to be provided at the cable end entering to the Main panel and including all labour and materials complete and as per specifications of this tender and directions of Engineer-in-charge. End Termination of Cable using jointing kits & accessories as recommended by cable/ kit manufacturer."<br>4Cx4 sq.mm PVC Cu. Cables <br>

od62679/2021_2022 : "LT CABLE TERMINATION<br>Supply erection, Termination of PVC insulated armoured / unarmoured cables up to 1100V grade and connection of leads including the supply of Aluminum/COPPER cable lugs but including cutting stripping of cable insulation, providing double compression type glands, terminals, and armour earthing ,crimping the lug on to the conductor, clamping of the cable-cores, marking with wire number ferrules, etc.with Gland hood to be provided at the cable end entering to the Main panel and including all labour and materials complete and as per specifications of this tender and directions of Engineer-in-charge. End Termination of Cable using jointing kits & accessories as recommended by cable/ kit manufacturer."<br>1C 25 Sq.mm. XLPE cu. FL. Cable <br>

od62680/2021_2022 : "LT CABLE TERMINATION<br>Supply erection, Termination of PVC insulated armoured / unarmoured cables up to 1100V grade and connection of leads including the supply of Aluminum/COPPER cable lugs but including cutting stripping of cable insulation, providing double compression type glands, terminals, and armour earthing ,crimping the lug on to the conductor, clamping of the cable-cores, marking with wire number ferrules, etc.with Gland hood to be provided at the cable end entering to the Main panel and including all labour and materials complete and as per specifications of this tender and directions of Engineer-in-charge. End Termination of Cable using jointing kits & accessories as recommended by cable/ kit manufacturer."<br>1C 6 Sq.mm. XLPE cu. FL. Cable <br>

od62888/2021_2022 : Supply, Fixing of the following size Copper flat earth Station with 2 Nos DMC supporting Insulator clamp with predrilled machine made holes of 12mm & 6 mm dia at 25mm intervals for fixing earth flat including Nuts,Bolts & Washers complete as required. (2Nos DMC supporting insulators shall be used for 400mm distance) <br>600 x 25 x 3mm thick copper earth flat<br>

od62889/2021_2022 : Supply, Installation, testing & commissioning of following INVERTER System with SMF batteries required for 15 min backup, MS powder coated battery racks., ventilation louver and covers, Battery control switch (MCCB) at Battery bank, Battery cable, intercell and cable between inverter and battery. The battery control switch shall be having under voltage provision. The breaker shall be fitted in the battery rack itself.3kVA <br><br>

od62909/2021_2022 : Supply, Installation, testing & commissioning of following INVERTER System with SMF batteries required for 15 min backup, MS powder coated battery racks., ventilation louver and covers, Battery control switch (MCCB) at Battery bank, Battery cable, intercell and cable between inverter and battery. The battery control switch shall be having under voltage provision. The breaker shall be fitted in the battery rack itself. 6KVA<br>

90.16.4.2 : Supply and clamping the following sizes of strips on surface of wall / parapet/ existing cable tray using clamps fabricated from 20 x3 mm GI flat duly painted or heavy duty GI spacer saddles, spacing of clamps not exceeding 1 m , making good the damages, colour washing etc. as required ( for vertical run).

od62992/2021_2022 : "CABLE TRAYS<br>Supply and erection of following size 2mm thick Ladder type, Pregalvanized, cable trays and cable tray of rolled GI Sheet, supports out sections, pipes, plates, etc. including welding, anchor bolts, threaded down rods(for 300 mm trays only), supply of necessary anchor bolts and grouting etc. including breaking walls, floors, etc. for structures as required including supply of all GI hardware materials, all labour and materials complete as per approved drawings, specifications of this tender and directions of Engineer-in-charge.The rate shall include supply & fixing of MS Grip bolts in columns/beams/walls/ceiling etc.as required & including drilling also. Rod supports shall be of galvanized full threaded rods of sizes 8,10 & 12mm dia for fixing to anchor fastener, anchor bolts.The length of the full threaded rods for the purposes of quoting shall be 1200 mm & includes nuts & washers and supports shall be at a min.distance of 1Mtr.The rate will include all required bends, tees, vertical up & downs, radius bends and other applicable accessories shall be factory fabricated, complete & as required."<br>300 x 50mm x2mmProffereated type cable trays <br>

od62993/2021_2022 : "CABLE TRAYS<br>Supply and erection of following size 2mm thick Ladder type, Pregalvanized, cable trays and cable tray of rolled GI Sheet, supports out sections, pipes, plates, etc. including welding, anchor bolts, threaded down rods(for 300 mm trays only), supply of necessary anchor bolts and grouting etc. including breaking walls, floors, etc. for structures as required including supply of all GI hardware materials, all labour and materials complete as per approved drawings, specifications of this tender and directions of Engineer-in-charge.The rate shall include supply & fixing of MS Grip bolts in columns/beams/walls/ceiling etc.as required & including drilling also. Rod supports shall be of galvanized full threaded rods of sizes 8,10 & 12mm dia for fixing to anchor fastener, anchor bolts.The length of the full threaded rods for the purposes of quoting shall be 1200 mm & includes nuts & washers and supports shall be at a min.distance of 1Mtr.The rate will include all required bends, tees, vertical up & downs, radius bends and other applicable accessories shall be factory fabricated, complete & as required."<br>150 x 50mm x2mm Proffereated type cable trays <br>

od63076/2021_2022 : Only Approved Make as listed in tender similar to PHILIPS REF. CAT.NO. 31450 "Supply of IP 65 up/downl LED fixture operating on 230VAC Mains with integrated driver. Power Supply should be intergral part of the luminaire. Max power consumption of 10W using high power quality LEDs. System lumen output shall be 670lm. Die cast alumunium housing & clear glass cover housing. Lumem maintenance shall be 70% at 25000 burning hours at 40 deg C. Operating temperature shall be -20deg to +40deg C. Housing shall be non corrosive pressure die cast aluminium. <br>

od63078/2021_2022 : Only Approved Make as listed in tender similar to Regent Hybec 40W LED Briged LUX white body colour dimension 900mm<br>

od63079/2021_2022 : Only Approved Make as listed in tender similar to Regent Hybec 40W LED Briged LUX white body colour dimension 600mm<br>

od63080/2021_2022 : Only Approved Make as listed in tender similar to Light matters KRISH PENDENT HANGING WITH 9W LED LAMP<br>

od63081/2021_2022 : Only Approved Make as listed in tender similar to REGENT CAT. NO.BOULE Pendant<br>

od63083/2021_2022 : Only Approved Make as listed in tender (PHILIPS REF. CAT.NO.LRM1071) Recessed mounted Occuswitch with moment dector and all necessary accesseries as required.<br>

od63084/2021_2022 : Only Approved Make as listed in tender similar to FullGlow 1'X4' LED luminaire with high transmitive diffuser similar to Philips Cat. No.RC380B LED43S-6500 G5 L3W12 PSU OD (DALI SUPPORT DRIVER)<br>

od63085/2021_2022 : Only Approved Make as listed in tender similar to CAT. NO.SERENO LED 28W HIGHEFFICIENCY DIFFUSER SUSPENDED MOUNTINGDIMENSION : 4FEET (L) X 45mm (H) (DALI SUPPORT DRIVER)<br>

od63086/2021_2022 : Only Approved Make as listed in tender similar to PHILIPS CAT. NO.MAHESH CHOPSTICK LED SP525P LED48S-6500 PSU NOT < 43W 4800 LUMEN. DIMENSION : 1220mm (L) X 102 mm (W) X 57mm (H) (DALI SUPPORT DRIVER)<br>

od63087/2021_2022 : Only Approved Make as listed in tender SIMILAR TO PHILIPS CAT. NO.BN308C LED60S-6500 L120 PSU WH 47W LUMINAIRE. SURFACE MOUNTED LED LUMINAIRES WITH ALL ACCESSERIES AS REQUIRED DIMENSION : 1157mm (L) X 44mm (D) X 51mm (H) <br>

od63088/2021_2022 : Only Approved Make as listed in tender SIMILAR TO PHILIPS CAT. NO. ENDURA WT201C LED 40S CW PSU S1 PC) SURFACE MOUNTED LED LUMINAIRES WITH ALL ACCESSERIES AS REQUIRED DIMENSION : 1265mm (L) X 85mm (D) X 88mm (H) <br>

od63089/2021_2022 : Only Approved Make as listed in tender similar to PHILIPS CAT. NO. SP 780X LED26S-6500PSU W5L113 OD WH PURELINE SLIM LED 50MM.4FEET - [email protected] DIMENSION: 1130mm(L) x 50mm(W) x 75mm(H)<br>

od63090/2021_2022 : Only Approved Make as listed in tender similar to PHILIPS CAT. NO. SSP780X LED12S-6500 PSU W5L56 OD WH PURELINE SLIM LED 50MM 2FEET - 1100lm@11W CUTOUT DIMENSION: 565mm(L) x 50mm(W) x 75mm(H)<br>

od63091/2021_2022 : Only Approved Make as listed in tender similar to PHILIPS CAT. NO. SP 780P LED26S-6500PSU W5L113 OD WH PURELINE SLIM LED 50MM.4FEET - [email protected] DIMENSION: 1130mm(L) x 50mm(W) x 75mm(H)<br>

od63092/2021_2022 : Only Approved Make as listed in tender similar to PHILIPS CAT. NO. SSP780P LED12S-6500 PSU W5L56 OD WH PURELINE SLIM LED 50MM 2FEET - 1100lm@11W CUTOUT DIMENSION: 565mm(L) x 50mm(W) x 75mm(H)<br>

od63094/2021_2022 : Only Approved Make as listed in tender similar to REGENT CAT. NO.LED0010WW0410000010J7FLEXIBLE RIBBON LUMINAIRE ASTRAL LED STRIP LIGHT CUTOUT DIMENSION: 16mm (W) 35mm (12)

od63095/2021_2022 : SIMILAR TO PHILIPS CAT. NO.DN394B LED 16S 6500 PSU WH 15W LUMINAIRE. RECESSED MOUNTED CIRCULAR DOWN LIGHTER DIMENSION : 135mm Ø X 70mm (H) <br>

od63098/2021_2022 : Only Approved Make as listed in tender similar to PHILIPS CAT. NO. RC380B LED36S -6500 G4 L60 W60 PSU OD 40W LED NW RECESSED MOUNTED LUMINARIESCUTOUT DIMENSION: 597mm (L) X 597mm (W) X 70mm (H)

od63154/2021_2022 : SIMILAR TO PHILIPS SUSPENDED DECORATIVE FIXUTRE DIMENSION: 600mm (dia) X 100mm (H) Lumen-3000<br>

od63155/2021_2022 : SIMILAR TO LIGHT MATTERS CAT. NO. HYBEC 40WLED BRIDGE LUX SURFACED MOUNTED DIMENSION: 600mm (dia) X 100mm (H) Lumen-3000<br>

od63156/2021_2022 : SIMILAR TO PHILIPS CAT. NO.SP780P LED44S-6500 PSU W5 OD WH SQ CONN STANDALONE LUMINAIRES SQUARE SUSPENDED MOUNTING 44W.DIMENSION: 2FEET(L) x 2FEET(W) x 50mm SLIM Lumen-4400<br>

od63157/2021_2022 : SIMILAR TO PHILIPS CAT. NO.SP780P LED44S-6500 PSU W5 OD WH HX CONN STANDALONE LUMINAIRES HEXAGON SUSPENDED MOUNTING 66W.DIMENSION: 2FEET(EACH ARM) x 50mm SLIM Lumen-6600<br>

od63158/2021_2022 : SIMILAR TO PHILIPS CAT. NO.Cone F008 RD-SERIES 40W DECORATIVE PENDANTS SURFACE MOUNTEDPK410 ROSÉGOUD (T302) SHADE TEXTURE CANOPYDIMENSION: 208(dia) x 152mm(H) Lumen-1500<br>

od63159/2021_2022 : SIMILAR TO PHILIPS CAT. NO.Torus Suspended LED FixtureDECORATIVE PENDANTS SURFACE MOUNTED 40W WITHWHITE CANOPY WOVEN OVAL (T302) SHADE TEXTUREDIMENSION: 204(dia) x 152mm(H)Lumen-3000<br>

od63160/2021_2022 : SIMILAR TO PHILIPS CAT. NO. APPLE F00 RD-SERIES 40W DECORATIVE PENDANTS SURFACE MOUNTED WITHBLACK CANOPY WOVEN ROUND (T303) SHADE TEXTUREDIMENSION: 200(dia) x 150mm(H) Lumen-1500<br>

od63161/2021_2022 : SIMILAR TO PHILIPS CAT. NO.SP320P LED15S 6500 PSUDIA100 WH 15W CYLINDRICAL SURFACE/ SUSPENDEDDOWNLIGHTER ALUMINIUM EXTUDED MATERIALDIMENSION: 100(dia) x 190mm(H) Lumen-1100<br>

od63162/2021_2022 : SIMILAR TO PHILIPS CAT. NO.TRACK LIGHT ST700T 22W PANE ANGLE 0-320° DIMENSION: ∅ 80mm X 135mm (LENGTH) Lumen-2000<br>

od63163/2021_2022 : SIMILAR TO PHILIPS CAT. NO.DHGATE GU 10 10HEADS LED DECORATIVE LIGHT FITITNG WITH LED 20INCH X 6' HEIGHT CRYSTAL CHANDELIER.20X7W DIMENSION: 700mm(dia) x 2000mm(H) 600 lm per lumen<br>

od63164/2021_2022 : SIMILAR TO PHILIPS REF. CAT.NO.LRM1071 RECESSED MOUNTED OCCUSWITCH WITH MOMENT DETECTOR AND ALL NECESSARY ACCESSERIES AS REQUIRED.24W DIMENSION: 195mm(Dia) x148mm(H) x 300mm cable length {Muilti colour) Lumen-1500<br>

od63165/2021_2022 : "SIMILAR TO PHILIPS CAT. NO.DN590B M LED20S 6500 PSD WH MB RECESSED MOUNTED CIRCULAR DOWN LIGHTER WITH HIGH EFFICIENCY TRANSLUCENCE DIFFUSER SUITABLE FOR 18W CUTOUT DIMENSION : 135mm Ø X 85mm (H) Lumen-200<br>"<br>

od64057/2021_2022 : Only Approved Make as listed in tender similar to (REGENT REF. CAT.NO.LED0115PS2807250040J7 ) Ceiling mounted Pendant Luminaire Ring LED . 40W.Colour temperature 3000/5700 K DIA -1200mm<br>

od64058/2021_2022 : Supply, fixing testing and commissioning of Bollard-14W- LED fitting Each Similar PHILIPS BCP 400 D "Supply of IP 65 Bollard LED fixture operating on 230VAC Mains with integrated driver. Power Supply should be intergral part of the luminaire. Max power consumption of 14W using high power quality LEDs. System lumen output shall be 800lm. Die cast alumunium housing & clear glass cover housing. Lumem maintenance shall be 70% at 50000 burning hours at 40 deg C. Operating temperature shall be -20deg to +40deg C. Impact resistance shall be IK08. Housing shall be non corrosive pressure die cast aluminium. <br>

od64059/2021_2022 : Only Approved Make as listed in tender similar to Philips Post top lamp including 3m tubular aluminium pole above the ground with concrete arrangement for post top luminaire jaguar Cat. No.BGP461 LED33 WW 110-277 TS 33W +/- 5 % decorative LED post top luminaire with System efficacy of more than 90 lm/W and having System Lumen Output of 3000 Lm. LED post top shall be made up of Die Cast aluminium housing suitable to mounted on 60 mm OD bracket arm. Luminaire shall have two separate compartments for LEDs and driver and both compartments should be hermitically sealed to achieve IP 65 ingress protection. Ambient temperature shall be 40 deg C and operating temperature shall be -40 to +50 Deg C. Optical compartment shall be provided with heat resistant clear toughened glass to withstand IK 08 impact rating, while control gear shall be provided with die cast aluminium cover for safety. LM 80-08 compliant, ANSI rated LEDs. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire manufacturer shall produce certificate of association with LED manufacturer for minimum five years. LED Street Light shall be with LEDs mounted on MCPCB of 1.5mm thickness to ensure proper heat dissipation from LEDs. LED optical lens should be properly fixed to MCPCB and should not be only fixed by glue. LED optical lens shall be made up of Glass/PMMA or Polycarbonate and shall have temperature withstand capacity of greater than 85 Deg C and transmittivity of more than 90%. The LED shall be compliant with LM80-08 standard with Useful L70 life of 50000 Hrs. The LEDs used in Street Light should be ANSI standard Rated LED with CCT of 3000K and CRI of Minimum 70. LED Driver shall be Isolated type, multistage Constant Current Constant Voltage topology driver in metal enclosure with proper heat sink for heat dissipation suitable to operate in input voltage range of 120V to 270V (nominal rated voltage – 240V) with 10 KV internal surge protection, Power factor greater than 0.9 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. <br>

od64885/2021_2022 : Supply fixing of the PVC trunking 100* x 38mm with necessary accessaries wall including cutting chippling, plastering in the floor/wall to make good finish to match with the floor/ wall etc.<br>

od64886/2021_2022 : Supply fixing of the 75 x 75 x 25 mm floor GI junction box with cover necessary civil works fixed in recessed system in floor including cutting chipping, plastering in the floor/wall to make good finish to match with the floor/ wall etc.<br>

od64887/2021_2022 : Supply fixing of the 400 x 400 x 65 mm floor GI junction box with cover necessary civil works fixed in recessed system in floor including cutting chipping, plastering in the floor/wall to make good finish to match with the floor/ wall etc.<br>

od64888/2021_2022 : Supply fixing of the 225 x 225 x 65 mm floor GI junction box with cover necessary civil works fixed in recessed system in floor including cutting chipping, plastering in the floor/wall to make good finish to match with the floor/ wall etc.<br>

od64889/2021_2022 : Supply fixing of the 150 x 150 x 65 mm floor GI junction box with cover necessary civil works fixed in recessed system in floor including cutting chipping, plastering in the floor/wall to make good finish to match with the floor/ wall etc.<br>

od64890/2021_2022 : Supply, fixing of the 225 x 38 mm GI Channel with cover two partition 1.6mm thick including stiffener at required intervals in recessed system in floor including 14 SWG Cu. earthing, cutting chipping, plastering in the floor/wall to make good finish to match with the floor /wall etc.<br>

od64906/2021_2022 : Supply, fixing of the 100 x 38 mm GI Channel with cover including stiffner at required intervals in recessed system in floor including 14 SWG Cu. earthing, cutting chipping, plastering in the floor/wall to make good finish to match with the floor /wall etc. (for UPS & Raw power)<br>

od167797/2021_2022 : Supply, Installation, testing & commissioning of following UPS System with built-in anti-harmonic filter, Preferably with active filter and all parameter in THDi and power factor shall be mentioned for percentage loading from 40% to 100%. , (internal cabling if any) for reducing input thdi to < 3 to 5% and improve PF togreater that or equal to 0.95. The same shall be feasible to use in suitable for parallel redundant configuration in future. This UPS shall have 3 phase input and three phase output as per the detailed specification, data sheet, drawings.. and Supply, Installation, testing & commissioning of SMF batteries required for 30 min backup using Global Yuasa / Equivalent make for UPS units, with MS powder coated battery racks. With ventilation louver and covers including Supply, Installation, testing & commissioning of Battery control switch ( MCCB ) at Battery bank . The battery control switch shall be having under voltage provision. The breaker shall be fitted in the battery rack itself.10KVA<br>

od167798/2021_2022 : Supply, Installation, testing & commissioning of following UPS System with built-in anti-harmonic filter, Preferably with active filter and all parameter in THDi and power factor shall be mentioned for percentage loading from 40% to 100%. , (internal cabling if any) for reducing input thdi to < 3 to 5% and improve PF togreater that or equal to 0.95. The same shall be feasible to use in suitable for parallel redundant configuration in future. This UPS shall have 3 phase input and three phase output as per the detailed specification, data sheet, drawings.. and Supply, Installation, testing & commissioning of SMF batteries required for 30 min backup using Global Yuasa / Equivalent make for UPS units, with MS powder coated battery racks. With ventilation louver and covers including Supply, Installation, testing & commissioning of Battery control switch ( MCCB ) at Battery bank . The battery control switch shall be having under voltage provision. The breaker shall be fitted in the battery rack itself.100KVA<br>

od167799/2021_2022 : Supply, Installation, testing & commissioning of following UPS System with built-in anti-harmonic filter, Preferably with active filter and all parameter in THDi and power factor shall be mentioned for percentage loading from 40% to 100%. , (internal cabling if any) for reducing input thdi to < 3 to 5% and improve PF togreater that or equal to 0.95. The same shall be feasible to use in suitable for parallel redundant configuration in future. This UPS shall have 3 phase input and three phase output as per the detailed specification, data sheet, drawings.. and Supply, Installation, testing & commissioning of SMF batteries required for 30 min backup using Global Yuasa / Equivalent make for UPS units, with MS powder coated battery racks. With ventilation louver and covers including Supply, Installation, testing & commissioning of Battery control switch ( MCCB ) at Battery bank . The battery control switch shall be having under voltage provision. The breaker shall be fitted in the battery rack itself. 40KVA<br>

od167800/2021_2022 : Preparation of the drawing and submission to the chief electrical inspectorate to govt.of Kerala, Kerala Electricity Board and other statutory authorities for commissioning the system including arranging inspection and also necessary approval / safety certificate from authorities etc. for the ELECTRICAL / Other services etc,. installation. The necessary statutory fees/charges will be paid by the client against demand advice.<br>

od168502/2021_2022 : Only Approved Make as listed in tender similar to PHILIPS CAT. NO. BN100C LED40S 6500 PSU L120 GR 40W LED SUITABLE FOR BOTH WALL AND SUSPENDED MOUNTING LUMINARIE CUTOUT DIMENSION: 1127mm (L) X 40mm (W) X 46mm (H) . Lumen-4000<br>

od168503/2021_2022 : Only Approved Make as listed in tender Foot light LED Philips BBP211 LED90/WW 2W 12V 30D<br>

od168504/2021_2022 : Only Approved Make as listed in tender similar to Regent Pendant luminaire Solo Slim with LED system power 45W LED white body colour dimension 750 mm, H = 70 mm,<br>

od168505/2021_2022 : Only Approved Make as listed in tender similar to Regent Pendant luminaire Solo Slim with LED system power: 35W, white body colour dimension 528 mm, H = 70mm<br>

od168506/2021_2022 : Only Approved Make as listed in tender LED Decorative light Fititng with Led 20inch x 6' height crystal chandelier<br>

od168508/2021_2022 : Only Approved Make as listed in tender similar to JAGUAR REF. CAT.NO. NERO SURFACE (ROUND) LNRO02R0118SC 18W SURFACE MOUNTED LED DOWNLIGHTER CUTOUT DIMENSION: 225mm (dia) X 30mm (H)<br>

od178268/2021_2022 : Only Approved Make as listed in tender similar to JAGUAR CAT. NO. LETS36R015XC WH 15W RECESSED MOUNTED LED DOWNLIGHTER CUTOUT DIMENSION: 118mm (dia) X 140mm (H) -

1.55.1 : Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group A

Signages

od168353/2021_2022 : Supplying and installing in position laminated sheet of "Fire Evacuation Plan". Providing wall mounting display board with double side 3mm thick imported acrylic sheet & glowsheet with SS Studs Digital color print on Traceperacy Sheets : Size 24"X18"<br>

od168354/2021_2022 : Supply, Installation of self glowing "Fire Pump Room" sign board of size 100mm X 300mm made of luminescent safely, rigid sheet in green color, photo luminescent rigid sheet with two each hanging chains and necessary supports to hand it on ceiling - with battery backup<br>

od168355/2021_2022 : Supplying and installing in position Exit LED Signage (Arrow) - green led lightning with Battery backup for 3 hrs<br>

od168356/2021_2022 : Supplying and installing in position "MCP" Signages ( Acrylic + Self Illumiated with LED Lights no backup, Triangular Type) : Size 15"X4"<br>

od168357/2021_2022 : Supplying and installing in position FIRE EXTINGUSHERS Signages ( Acrylic + Self Illumiated with LED Lights no backup, Triangular Type) Size 15"X4"<br>

od168358/2021_2022 : Supplying and installing in position FIRE CABINET Signages ( Acrylic + Self Illumiated with LED Lights no backup) Size 12"X4"<br>

od168359/2021_2022 : Supplying and installing in position FIRE LIFT Signages ( Acrylic + Self Illumiated) Size 12"X4"<br>

od168360/2021_2022 : Supplying and installing in position Safe Assemble Point with 8 feet Size 2"X1"<br>

od168361/2021_2022 : Supplying and installing in position Way to safe assemble point with 8 feet Size 2"X1"

od168363/2021_2022 : Supplying and installing in position Fire Order Board 3"X2"

od168364/2021_2022 : Supplying and installing in position LIFT Signages Acrylic + Self Illuminated Size 8"X8"

od168365/2021_2022 : Supplying and installing in position STAIRCASE SIGNAGES Acrylic + Self Illuminated Size 16"X6"

HVAC- VARIABLE REFRIGERANT FLOW SYSTEM

od52023/2021_2022 : INDOOR UNITS:<br> Design, Supply, Installation, testing and commissioning of BMS Compatible VRF Indoor air conditioning units with direct driven fan, high efficient filter, inbuilt microprocessor thermostat, electronic expansion valve, provision of fresh air duct connection, remote controller including cable, drain pump set (for cassette units and hi-static ductable units), necessary ceiling supports & vibration isolators, refrigerant charging, Refnet joints (Refrigerant branch kit) for both liquid and gas line branch kits, oil charging, control wiring, power cable from the nearest socket including plug, and drain connection, etc. The capacities are as mentioned below:- <br>Ceiling Mounted Cassette Unit (VRF)<br>a).Cooling Capacity - 2.0 TR

od162640/2021_2022 : INDOOR UNITS: Design, Supply, Installation, testing and commissioning of BMS Compatible VRF Indoor air conditioning units with direct driven fan, high efficient filter, inbuilt microprocessor thermostat, electronic expansion valve, provision of fresh air duct connection, remote controller including cable, drain pump set (for cassette units and hi-static ductable units), necessary ceiling supports & vibration isolators, refrigerant charging, Refnet joints (Refrigerant branch kit) for both liquid and gas line branch kits, oil charging, control wiring, power cable from the nearest socket including plug, and drain connection, etc. The capacities are as mentioned below:- <br>Ceiling Mounted Treated Fresh Air Unit (VRF)<br>1).Cooling Capacity - 4.0 TR <br>

od52024/2021_2022 : INDOOR UNITS:<br> Design, Supply, Installation, testing and commissioning of BMS Compatible VRF Indoor air conditioning units with direct driven fan, high efficient filter, inbuilt microprocessor thermostat, electronic expansion valve, provision of fresh air duct connection, remote controller including cable, drain pump set (for cassette units and hi-static ductable units), necessary ceiling supports & vibration isolators, refrigerant charging, Refnet joints (Refrigerant branch kit) for both liquid and gas line branch kits, oil charging, control wiring, power cable from the nearest socket including plug, and drain connection, etc. The capacities are as mentioned below:- <br>Ceiling Mounted Cassette Unit (VRF)<br>b).Cooling Capacity - 1.6 TR

od52025/2021_2022 : INDOOR UNITS: <br>Design, Supply, Installation, testing and commissioning of BMS Compatible VRF Indoor air conditioning units with direct driven fan, high efficient filter, inbuilt microprocessor thermostat, electronic expansion valve, provision of fresh air duct connection, remote controller including cable, drain pump set (for cassette units and hi-static ductable units), necessary ceiling supports & vibration isolators, refrigerant charging, Refnet joints (Refrigerant branch kit) for both liquid and gas line branch kits, oil charging, control wiring, power cable from the nearest socket including plug, and drain connection, etc. The capacities are as mentioned below:- <br>Ceiling Mounted Cassette Unit (VRF)<br>c).Cooling Capacity - 1.3 TR

od52082/2021_2022 : INDOOR UNITS: <br>Design, Supply, Installation, testing and commissioning of BMS Compatible VRF Indoor air conditioning units with direct driven fan, high efficient filter, inbuilt microprocessor thermostat, electronic expansion valve, provision of fresh air duct connection, remote controller including cable, drain pump set (for cassette units and hi-static ductable units), necessary ceiling supports & vibration isolators, refrigerant charging, Refnet joints (Refrigerant branch kit) for both liquid and gas line branch kits, oil charging, control wiring, power cable from the nearest socket including plug, and drain connection, etc. The capacities are as mentioned below:- <br>Ceiling Mounted Cassette Unit (VRF)<br>d).Cooling Capacity - 1.0 TR

od52083/2021_2022 : INDOOR UNITS: <br>Design, Supply, Installation, testing and commissioning of BMS Compatible VRF Indoor air conditioning units with direct driven fan, high efficient filter, inbuilt microprocessor thermostat, electronic expansion valve, provision of fresh air duct connection, remote controller including cable, drain pump set (for cassette units and hi-static ductable units), necessary ceiling supports & vibration isolators, refrigerant charging, Refnet joints (Refrigerant branch kit) for both liquid and gas line branch kits, oil charging, control wiring, power cable from the nearest socket including plug, and drain connection, etc. The capacities are as mentioned below:- <br>Ceiling Mounted Duct Unit (VRF)<br>1).Cooling Capacity - 3.0 TR <br>

od52084/2021_2022 : INDOOR UNITS: <br>Design, Supply, Installation, testing and commissioning of BMS Compatible VRF Indoor air conditioning units with direct driven fan, high efficient filter, inbuilt microprocessor thermostat, electronic expansion valve, provision of fresh air duct connection, remote controller including cable, drain pump set (for cassette units and hi-static ductable units), necessary ceiling supports & vibration isolators, refrigerant charging, Refnet joints (Refrigerant branch kit) for both liquid and gas line branch kits, oil charging, control wiring, power cable from the nearest socket including plug, and drain connection, etc. The capacities are as mentioned below:- <br>Ceiling Mounted Cassette Unit (VRF)<br>e).Cooling Capacity - 0.8 TR <br>

od52174/2021_2022 : Design, Supply, installation, testing and commissioning of AHU Starter Panel with DOL/Star-Delta starter and BMS compatible Variable Frequency Drive with controller with auto bye pass arrangement. The VFD shall have Frequency controller, Microprocessor based logic controller, integrated Software capable to control frequency based on the inputs from sensors, power cable from VFD to AHU, communication cable, Communication card (BACnet protocol) to transfer the entire data available on VFD to the third party BMS System. The VFD shall have IP-20 protection and panel shall have IP42 protection. <br>Motor rating: 5.5 kW

od52175/2021_2022 : Floor standing Air Handling unit (VRF): Design, Supply, installation, testing and commissioning of Double Skin Air Handling Units of Horizontal Configuration, 45±5mm thick panel with PUF insulation, MERV 8 & 13 filter sections, DX coil with single / multiple DX cooling coil suitable for R-410a refrigerant copper tube & aluminium fins, copper header, single/multiple expansion kit, communication kit, backward curved centrifugal fan, belt driven motor, spring vibration isolator for fan and motor, factory assembled volume control damper, internal power and control wiring, required length of power cable from the starter panel/VFD to the equipment, GI base frame complete as per specifications as required. Fan motor shall be suitable for 415±10% volts, 50 cycles, 3 phase AC supply & high efficiency (IE-3) and suitable for VFD operation <br>"Capacity: 20.0 TR, Dehumidified Air: 7500 CFM, ESP: 25mmWC, <br>Motor Rating: 5.5 kW "

od52190/2021_2022 : Supply, installation, testing and commissioning of Temperature & RH sensors with transmitters for transferring the signal to the VFD logic controller. The rate shall be inclusive of required length shielded copper communication cable for successful functioning of VFD Logic controller system.

od52191/2021_2022 : "REFRIGERANT PIPING & RELATED WORKS: <br>Supply and erection of 16 Gauge Hard drawn Refrigerant Copper pipes to integrate outdoor / indoor units. The rate shall inclusive of closed cell nitrile rubber insulation for copper pipes and fibre glass cloth covering. The FRP / Polyshield coating shall be applied over the insulation for exposed application. The pipe sizes and insulation thickness as follows."<br>41.3mm dia with 19mm thick insulation<br>

od52192/2021_2022 : "REFRIGERANT PIPING & RELATED WORKS: <br>Supply and erection of 16 Gauge Hard drawn Refrigerant Copper pipes to integrate outdoor / indoor units. The rate shall inclusive of closed cell nitrile rubber insulation for copper pipes and fibre glass cloth covering. The FRP / Polyshield coating shall be applied over the insulation for exposed application. The pipe sizes and insulation thickness as follows."<br>34.9mm dia with 19mm thick insulation<br>

od52193/2021_2022 : "REFRIGERANT PIPING & RELATED WORKS: <br>Supply and erection of 16 Gauge Hard drawn Refrigerant Copper pipes to integrate outdoor / indoor units. The rate shall inclusive of closed cell nitrile rubber insulation for copper pipes and fibre glass cloth covering. The FRP / Polyshield coating shall be applied over the insulation for exposed application. The pipe sizes and insulation thickness as follows."<br>28.6mm dia with 19mm thick insulation<br>

od52194/2021_2022 : "REFRIGERANT PIPING & RELATED WORKS: <br>Supply and erection of 16 Gauge Hard drawn Refrigerant Copper pipes to integrate outdoor / indoor units. The rate shall inclusive of closed cell nitrile rubber insulation for copper pipes and fibre glass cloth covering. The FRP / Polyshield coating shall be applied over the insulation for exposed application. The pipe sizes and insulation thickness as follows."<br>22.2mm dia with 19mm thick insulation<br>

od52195/2021_2022 : "REFRIGERANT PIPING & RELATED WORKS: <br>Supply and erection of 16 Gauge Hard drawn Refrigerant Copper pipes to integrate outdoor / indoor units. The rate shall inclusive of closed cell nitrile rubber insulation for copper pipes and fibre glass cloth covering. The FRP / Polyshield coating shall be applied over the insulation for exposed application. The pipe sizes and insulation thickness as follows."<br>19.1mm dia with 19mm thick insulation<br>

od52196/2021_2022 : "REFRIGERANT PIPING & RELATED WORKS: <br>Supply and erection of 16 Gauge Hard drawn Refrigerant Copper pipes to integrate outdoor / indoor units. The rate shall inclusive of closed cell nitrile rubber insulation for copper pipes and fibre glass cloth covering. The FRP / Polyshield coating shall be applied over the insulation for exposed application. The pipe sizes and insulation thickness as follows."<br>15.9mm dia with 19mm thick insulation<br>

od52197/2021_2022 : "REFRIGERANT PIPING & RELATED WORKS: <br>Supply and erection of 16 Gauge Hard drawn Refrigerant Copper pipes to integrate outdoor / indoor units. The rate shall inclusive of closed cell nitrile rubber insulation for copper pipes and fibre glass cloth covering. The FRP / Polyshield coating shall be applied over the insulation for exposed application. The pipe sizes and insulation thickness as follows."<br>12.7mm dia with 19mm thick insulation

od52198/2021_2022 : "REFRIGERANT PIPING & RELATED WORKS: <br>Supply and erection of 16 Gauge Hard drawn Refrigerant Copper pipes to integrate outdoor / indoor units. The rate shall inclusive of closed cell nitrile rubber insulation for copper pipes and fibre glass cloth covering. The FRP / Polyshield coating shall be applied over the insulation for exposed application. The pipe sizes and insulation thickness as follows."<br>9.5mm dia with 19mm thick insulation<br>

od52199/2021_2022 : REFRIGERANT PIPING & RELATED WORKS: <br>Supply and erection of 16 Gauge Hard drawn Refrigerant Copper pipes to integrate outdoor / indoor units. The rate shall inclusive of closed cell nitrile rubber insulation for copper pipes and fibre glass cloth covering. The FRP / Polyshield coating shall be applied over the insulation for exposed application. The pipe sizes and insulation thickness as follows.<br>6.4mm dia with 19mm thick insulation

od52200/2021_2022 : OUTDOOR UNITS: <br>Supply, Installation, testing and commissioning of Outdoor units consists of 100% inverter scroll compressor / Twin Rotary compressors, DC fan motor with aero-spiral fan blade, e-pass heat exchanger, safety valves, solenoid valves, receiver, capillary tube, check valve, electronic expansion valve, high pressure switch, low pressure sensor, pressure regulating valve, refrigerant filter, stop valve, accumulator and refnet kits. Rate inclusive of R-410A refrigerant & oil pre charging, power cable from nearest isolator, vibration isolators, supports, necessary foundation / pedestal works etc. (High COP Models)<br>16 HP

od162652/2021_2022 : OUTDOOR UNITS: Supply, Installation, testing and commissioning of Outdoor units consists of 100% inverter scroll compressor / Twin Rotary compressors, DC fan motor with aero-spiral fan blade, e-pass heat exchanger, safety valves, solenoid valves, receiver, capillary tube, check valve, electronic expansion valve, high pressure switch, low pressure sensor, pressure regulating valve, refrigerant filter, stop valve, accumulator and refnet kits. Rate inclusive of R-410A refrigerant & oil pre charging, power cable from nearest isolator, vibration isolators, supports, necessary foundation / pedestal works etc. (High COP Models)<br>20 HP<br>

od52201/2021_2022 : OUTDOOR UNITS: <br>Supply, Installation, testing and commissioning of Outdoor units consists of 100% inverter scroll compressor / Twin Rotary compressors, DC fan motor with aero-spiral fan blade, e-pass heat exchanger, safety valves, solenoid valves, receiver, capillary tube, check valve, electronic expansion valve, high pressure switch, low pressure sensor, pressure regulating valve, refrigerant filter, stop valve, accumulator and refnet kits. Rate inclusive of R-410A refrigerant & oil pre charging, power cable from nearest isolator, vibration isolators, supports, necessary foundation / pedestal works etc. (High COP Models)<br>22 HP

od52202/2021_2022 : OUTDOOR UNITS: <br>Supply, Installation, testing and commissioning of Outdoor units consists of 100% inverter scroll compressor / Twin Rotary compressors, DC fan motor with aero-spiral fan blade, e-pass heat exchanger, safety valves, solenoid valves, receiver, capillary tube, check valve, electronic expansion valve, high pressure switch, low pressure sensor, pressure regulating valve, refrigerant filter, stop valve, accumulator and refnet kits. Rate inclusive of R-410A refrigerant & oil pre charging, power cable from nearest isolator, vibration isolators, supports, necessary foundation / pedestal works etc. (High COP Models)<br>26 HP

od52375/2021_2022 : Supply and erection of the following UPVC pipe with all joints, reducer, necessary elbows and tees, supporting arrangements, etc. Rate shall inclusive of thermal insulation with 13mm thickness FM approved closed cell nitrile rubber insulation covering with fire resistant fibre cloth fabric as a resistant to Scratch & Mechanical Impact..<br>25 NB

od52376/2021_2022 : Supply and erection of the following UPVC pipe with all joints, reducer, necessary elbows and tees, supporting arrangements, etc. Rate shall inclusive of thermal insulation with 13mm thickness FM approved closed cell nitrile rubber insulation covering with fire resistant fibre cloth fabric as a resistant to Scratch & Mechanical Impact..<br>32 NB<br>

od52377/2021_2022 : Supply and erection of the following UPVC pipe with all joints, reducer, necessary elbows and tees, supporting arrangements, etc. Rate shall inclusive of thermal insulation with 13mm thickness FM approved closed cell nitrile rubber insulation covering with fire resistant fibre cloth fabric as a resistant to Scratch & Mechanical Impact..<br>40 NB

od52378/2021_2022 : Supply and laying of 2C x 0.75 Sqmm PVC Copper Armoured Cable - Control cabling for wired remote controller.

od52379/2021_2022 : Supply and laying of 2C x 1.5 Sqmm PVC Copper Armoured Cable - Communication and Control cabling between indoor and outdoor units. The rate shall be including suitable size MS conduit with conduit accessories and necessary fixing arrangement.<br>

od52380/2021_2022 : Supply and erection of following sizes perforated type cable tray made out of 16G thick GI sheet folded to required shape with adequate number of supports for Insulated refrigerant pipe and cable conduits. The tray shall be covered 16G GI sheet at all over the cable tray with screwing to cable tray as shown in the drawing.<br>450mm wide

od52381/2021_2022 : Supply and erection of following sizes perforated type cable tray made out of 16G thick GI sheet folded to required shape with adequate number of supports for Insulated refrigerant pipe and cable conduits. The tray shall be covered 16G GI sheet at all over the cable tray with screwing to cable tray as shown in the drawing.<br>300mm wide

od52382/2021_2022 : Supply and erection of following sizes perforated type cable tray made out of 16G thick GI sheet folded to required shape with adequate number of supports for Insulated refrigerant pipe and cable conduits. The tray shall be covered 16G GI sheet at all over the cable tray with screwing to cable tray as shown in the drawing.<br>150mm wide

od52657/2021_2022 : AIR DISTRIBUTION SYSTEM: Note: The colour shade for the air distribution equipments like ducts, diffusers, grilles, etc shall be approved by the Client / Architects before procurement and execution. The powder coating shall be 50 to 40 microns.The air distribution system comprises with all supports like anchor fasteners and tie-rods, cradles, angle iron supports, bolts and nuts, 4mm thick self-adhesive neoprene rubber gasket, stiffeners, zinc chromate painted angle iron flanges, chipping and plastering of openings made for duct supports etc., filling the gap with fibre glass wool and with fire sealant complete as per specification. The rates quoted shall include turning vanes, straightening vanes, splitters, inspection doors probe, provisions for BAS sensors, inlets with test openings enclosures complete with locking caps, chain, gaskets, insulating plugs, and extension for insulated ductwork etc. <br>Supply, installation, testing and balancing of Air Distribution System consists of factory fabricated Rectangular duct Galvanized Iron sheet metal ducting (Zinc coating 120GSM) with TDF/TDC flanges <br>d).0.63mm thick GSS ducting (24G) – factory fabricated

od52746/2021_2022 : Supply, installation, testing and balancing of Air Distribution System consists of Site fabricated Rectangular duct Galvanized Iron sheet metal ducting (Zinc coating 120GSM) with TDF/TDC flanges <br>0.63mm thick GSS ducting (24G)

od52886/2021_2022 : Supply, installation, testing and balancing of GI Round duct as per above specification. The Sheet thickness shall be 24G

od52887/2021_2022 : Supply, Installation, testing and commissioning of double skin plenum box. The frame work shall be of Extruded Aluminium hollow sections. 23±2 mm thick Double Skin Panels shall be made of 0.6mm Pre-coated GSS on outside and 0.6mm Plain GSS sheet inside with CFC free Polyurethane Foam of 40±2 kg/cum in-house injected in between. These panels shall be screwed from inside on to the frame work with soft rubber gasket in between to make the joints air tight. Framework for each section shall be joined together with soft rubber gasket in between to make the joints air tight. Suitable opening for SA duct shall be made. The plenum box skin colour shall match with the AHU skin colour.<br>

od52888/2021_2022 : Supply and fixing of Acoustic lining of wall and ceiling of AHU rooms with 50mm thick density 32Kg/Cu.m resin bonded glass fibber insulation friction fixed in 610mm X 610mm frame work made of 25X50X50X50X25mm made out of .6mm thick G.I Sheet U shaped channel and covered with reinforced fibre glass tissue and finished with .80mm perforated aluminium sheet etc. Complete as per Specifications. <br>

od52889/2021_2022 : Supply and installing of Acoustic insulation, Material shall be processed Nitrile Rubber foam. The material should be fibre free. The density of the same shall be within 140-180 Kg/m3.The material should have a thermal conductivity not exceeding 0.050 W/mK. The maximum surface temperature the material should withstand is 105º C and minimum temperature should be -20ºC. The Thickness of the material shall be 15mm. The material should conform to Class 1 rating for surface spread of Flame as per BS 476 Part 7. <br>

od52890/2021_2022 : Supply and erection of Thermal Insulation of Supply air duct with 9mm thick closed cell nitrile rubber temperature range from -10ºC to +60ºC, Class O fire category and as per specification.

od52891/2021_2022 : Supply and installation of Flexible duct connections between main duct to diffuser plenums and main duct to cassette units shall be 25mm thick fiber glass pre-insulated, single ply/multiply Aluminium construction and with multiple layers of polyester film glass fibber covered with mechanical lock sheets/ Aluminium laminated jackets-Fire resistant complete with Pre-fabricated and powder coated Aluminium angle frame mounting brackets and supports.<br>300mm dia

od52892/2021_2022 : Supply and installation of Flexible duct connections between main duct to diffuser plenums and main duct to cassette units shall be 25mm thick fiber glass pre-insulated, single ply/multiply Aluminium construction and with multiple layers of polyester film glass fibber covered with mechanical lock sheets/ Aluminium laminated jackets-Fire resistant complete with Pre-fabricated and powder coated Aluminium angle frame mounting brackets and supports.<br>250mm dia

od52893/2021_2022 : Supply and installation of Flexible duct connections between main duct to diffuser plenums and main duct to cassette units shall be 25mm thick fiber glass pre-insulated, single ply/multiply Aluminium construction and with multiple layers of polyester film glass fibber covered with mechanical lock sheets/ Aluminium laminated jackets-Fire resistant complete with Pre-fabricated and powder coated Aluminium angle frame mounting brackets and supports.<br>100mm dia

od52894/2021_2022 : Supply and fixing of Spigot damper shall be installed from take off collar to diffuser plenum boxes and at plenum boxes (low leakage) made out of 18G galvanized sheet steel frame and blades of 20G galvanized steel with suitable links.<br>300mm dia<br>

od52895/2021_2022 : Supply and fixing of Spigot damper shall be installed from take off collar to diffuser plenum boxes and at plenum boxes (low leakage) made out of 18G galvanized sheet steel frame and blades of 20G galvanized steel with suitable links.<br>250mm dia<br>

od52896/2021_2022 : Supply and fixing of Spigot damper shall be installed from take off collar to diffuser plenum boxes and at plenum boxes (low leakage) made out of 18G galvanized sheet steel frame and blades of 20G galvanized steel with suitable links.<br>100mm dia<br>

od52897/2021_2022 : Supply and installation of Powder coated extruded aluminum Circular diffuser with Panel suitable for false ceiling, dropper connection, volume control damper for supply air as per specifications.350mm dia<br>

od52898/2021_2022 : Supply and installation of Powder coated extruded aluminium Circular Diffusers with Panel suitable for false ceiling without volume control damper for return air as per specifications.350mm dia<br>

od52899/2021_2022 : Supply and installation of Acoustic insulated plenum boxes for supply air diffusers with 12mm thick, 48 kg/Cu.m density open cell nitrile rubber insulation to the plenum box with nuts and bolts.<br>375x375 - 450mm height<br>

od52900/2021_2022 : Supply and installation of Acoustic insulated plenum boxes for supply air diffusers with 12mm thick, 48 kg/Cu.m density open cell nitrile rubber insulation to the plenum box with nuts and bolts.<br>300x300 - 400mm height

od52901/2021_2022 : Supply and installation of Powder coated extruded aluminium linear grilles with 15 degree deflection with volume control damper for supply air Grille.<br>

od52902/2021_2022 : Supply and installation of Powder coated extruded aluminium continuous linear grilles with 0 degree deflection without volume control damper for exhaust /Return air Grille.<br>

od52903/2021_2022 : Supply, installation, testing and balancing of GI louver volume control damper (low leakage) made out of 1.6mm thick galvanised sheet steel frame and blades of 1.6mm galvanised steel with suitable links, handles, levers and quadrants for manual control of volume of air flow and for proper balancing of air distribution system.<br>

od52904/2021_2022 : Supply and installation of Non return damper of gravity type. The damper shall be made up of 16G thick GSS and less leakage type. The rate shall inclusive of necessary fixing and supporting arrangement.<br>

od52905/2021_2022 : Design, Supply, installation, testing and commissioning of motorized Fire damper in supply air/return air/exhaust air streams. The damper shall be made out of 16G thick galvanized sheet steel frame and blades of 16G galvanized steel with air tight arrangement. The damper shall be provided with control panel, BMS compatible actuator of the motorized Damper shall have required torque to ON / OFF the actuator with 220 V / 24 V transformer duly encased and wired, combined smoke and heat sensor and transmitters, control / communication cables, etc. The control panel shall be suitable for receive/send signal from the Fire Alarm System and status shall be monitored thru BMS.<br>Smoke & Fire Dampers.<br>

od52906/2021_2022 : BMS compatible Actuators with Control Panel & Wiring

od52907/2021_2022 : Supply, fixing, testing and balancing of Aluminium powder coated Fresh air and exhaust arrangement with storm proof louvers, volume control damper, MS weld mesh bird screen / mounting frame - 100mm louver spacing and 45 deg angle suitable for protection against splashing rain water fixed within a right aluminium frame.

od52908/2021_2022 : Supply and installation of Fire Retardant Canvass connections with GI matching flanges on both sides with a provision of openable zip. The entire assembly shall be factory fabricated.

od52909/2021_2022 : Design, Supply and erection of steel supports like MS plate, angles, channels, etc. Rate shall inclusive of cutting, welding, grinding, fixing accessories and one coat of primer & two coats of enamel paints, etc. as required.

od52910/2021_2022 : Design, Supply, installation, testing and commissioning of Fresh air Fan Units. The unit shall be single skin, belt driven centrifugal fan, High efficiency motor , spring vibration isolator for fan and motor, Fire retardant canvass connections, internal power and control wiring, GI base frame complete as per specifications as required. The cost shall inclusive of BMS compatible starter panel, required power cabling between the starter panel and fans, mounting arrangements, etc. Fan motor shall be suitable for 1 phase AC supply . <br>Air Qty: 1200 CFM, ESP: 20mmWC Fresh air fan for with EU-4 Filter

Lighting

od271577/2021_2022 : "SIMILAR TO PHILIPS CAT. NO.SP780X LED22S 4000 IAO LINEAR SUSPENDED MOUNTED WITH INTEGRATED IOT BASED WIRELESS SENSOR. SENSOR SHOULD BE SINGLE PIXLE THERMOPILE FOR PEOPLE COUNT, RF ENABLED FOR WIRELESS COMMUNICATION ALSO CAPABLE OF DAYLIGHT SENSOR, PIR OCCUPANCY SENSOR AND SOUND PRESSURE SENSOR. WATTAGE <22W, SYSTEM LUMEN >2200lm, 50K BURNING HOURS @L70<br>"<br>

od271578/2021_2022 : "SIMILAR TO PHILIPS CAT. NO.SP780X LED22S 3000-6500 PSD LINEAR SUSPENDED MOUNTED TUNNABLE LUMINAIRE, . WATTAGE <22W, SYSTEM LUMEN >2200lm, 50K BURNING HOURS @L70<br>"<br>

od271580/2021_2022 : "SIMILAR TO PHILIPS CAT. NO.RC380B LED36S 4000 IAO RECESS MOUNTED 2'X2' WITH INTEGRATED IOT BASED WIRELESS SENSOR. SENSOR SHOULD BE SINGLE PIXLE THERMOPILE FOR PEOPLE COUNT, RF ENABLED FOR WIRELESS COMMUNICATION ALSO CAPABLE OF DAYLIGHT SENSOR, PIR OCCUPANCY SENSOR AND SOUND PRESSURE SENSOR. WATTAGE <30W, SYSTEM LUMEN >3600lm, 50K BURNING HOURS @L70<br>"<br>

od271583/2021_2022 : "SIMILAR TO PHILIPS CAT. NO.DN590 LED20 4000 IAO RECESS MOUNTED IOT BASED DOWNLIGH WITH UGR<19. CRI>80 - Ra>=80, R9>=0, <18W, SYSTEM LUMEN >2000lm. BEAM ANGLE OF 38 - 60DEG, 140 - 270V, 50K BURNING HOURS @L70<br>"<br>

od271585/2021_2022 : "SIMILAR TO PHILIPS CAT. NO.DN590 LED20 3000-6500 RECESS MOUNTED BASED DOWNLIGH WITH UGR<19. CRI>80 - Ra>=80, R9>=0, <18W, SYSTEM LUMEN >2000lm. BEAM ANGLE OF 38 - 60DEG, 140 - 270V, 50K BURNING HOURS @L70<br>"<br>

od271586/2021_2022 : "SIMILAR TO PHILIPS CAT. NO.LS170 LED8 840 PSD LED STRIP WITH SUITABLE ALUMINIUM PROFILE & DIFFUSER FOR SEAMLESS LIGHT DISTRIBUTION. DIMMABLE LED STRIP WITH POSSIBLE OF CUT AND JOINT PROVISION AT EVERY 10cm, <9W, >800 SYSTEM LUMEN, CE APPROBATION. SDCM<4, 50K BURNING HOURS @L70.<br>"<br>

od271589/2021_2022 : "SIMILAR TO PHILIPS CAT. NO. RD-IND-F008-T204-BK402-S-CANCONE-BK402-BK00-300-N-2, DECORATIVE CONE SHAPEDCOMPLETELY RECYCLABLE LUMINAIRE IN THE COLOR OF SATIN BLACK WITH NATURAL LINE TEXTURE. LAMP SHOULD BE 15W WITH E27 BASE AND SYSTEM LUMEN OF 1300LUMEN. SUITABLE FOR IOT COMMUNICATION<br>"<br>

od271590/2021_2022 : "SIMILAR TO PHILIPS CAT. NO. RD-EUR-F002-T303-WH401-S-CANCONE-WH401-WH00-300-FIL-2, DECORATIVE PEAR SHAPED COMPLETELY RECYCLABLE LUMINAIRE IN THE COLOR OF EITHER BLACK/WHITE/SATIN GOLD/METALIC BLUE/METALIC PURPLE WITH NATURAL LINE TEXTURE/WOVEN ROUND TEXTURE. LAMP SHOULD BE 15W WITH E27 BASE AND SYSTEM LUMEN OF 1300LUMEN. SUITABLE FOR IOT COMMUNICATION<br>"<br>

od271592/2021_2022 : SIMILAR TO PHILIPS CAT. NO. LED vintage LED lamp with DECORATIVE SUSPENSION 20INCH X 6' HEIGHT CHANDELIER.20X7W DIMENSION: 700mm(dia) x 2000mm(H)<br>

od271594/2021_2022 : "SIMILAR TO PHILIPS CAT. NOST700T LED20 940PW PSD VLC MB WH IN DIMMABLE DOWNLIGHT WITH TRACK, CRI>90, SDCM<3, WATTAGE <22W, SYSTEM LUMEN >2200lm. 50K BURNING HOURS @L70. FLICKER FREE, SUITBALE FOR IOT PLATFORM <br>"<br>

od271597/2021_2022 : "SIMILAR TO PHILIPS CAT. NO.RS378B P15 + suspended kit tunnable DALI DOWNLIGH WITH CRI>80, WATTAGE <15W, SYSTEM LUMEN >1100lm. 50K BURNING HOURS @L70 or equivalent model <br>"<br>

od271599/2021_2022 : "SIMILAR TO PHILIPS CAT. NO. RD-EUR-F001-T303-PU410-S-CANCONE-BK402-BK00-300-FIL-2, DECORATIVE APPLE SHAPED COMPLETELY RECYCLABLE LUMINAIRE IN THE COLOR OF EITHER BLACK/WHITE/SATIN GOLD/METALIC BLUE/METALIC PURPLE WITH NATURAL LINE TEXTURE/WOVEN ROUND TEXTURE. LAMP SHOULD BE 15W WITH E27 BASE AND SYSTEM LUMEN OF 1300LUMEN. SUITABLE FOR IOT COMMUNICATION<br>"<br>

od271600/2021_2022 : SIMILAR TO PHILIPS CAT. NO.TORUS RING PENDANT LED FIXTURE DECORATIVE PENDANTS SURFACE/SUSPENDED MOUNTED 30W WITH WHITE SHADE TEXTUREDIMENSION: 450 - 600mm DIA, 70-100mm H, WATTAGE <36W, SYSTEM LUMEN >3000<br>

od271601/2021_2022 : "SIMILAR TO PHILIPS CAT. NO. RD-EUR-F008-T303-GR000-S-CANCONE-BK402-BK00-300-FIL-2, DECORATIVE CONE SHAPED COMPLETELY RECYCLABLE LUMINAIRE IN THE COLOR OF EITHER BLACK/WHITE/SATIN GOLD/METALIC BLUE/METALIC PURPLE WITH NATURAL LINE TEXTURE/WOVEN ROUND TEXTURE. LAMP SHOULD BE 15W WITH E27 BASE AND SYSTEM LUMEN OF 1300LUMEN. SUITABLE FOR IOT COMMUNICATION<br>"<br>

od271602/2021_2022 : SIMILAR TO PHILIPS CAT. NO.SP780P LED66S-6500 PSU/PSD W5 OD WH HEXADECIMAL STANDALONE LUMINAIRES SUSPENDED MOUNTING 66W.DIMENSION: 2FEET(L) ARM x 50mm SLIM Lumen-6600<br>

od271603/2021_2022 : SIMILAR TO PHILIPS CAT. NO.SP780P LED44S-6500 PSU/PSD W5 OD WH SQ CONN STANDALONE LUMINAIRES SQUARE SUSPENDED MOUNTING 44W.DIMENSION: 2FEET(L) x 2FEET(W) x 50mm SLIM Lumen-4400<br>

od271604/2021_2022 : SIMILAR TO PHILIPS CAT. NO.PANACHE MOD NO. 58130PENDENT LIGHTING <15W COLOUR STAINLESS STEELE27 LAMP BASEDIMENSION: 410mm(dia) x 1500mm(H) Lumen-1300<br>

od271605/2021_2022 : SIMILAR TO LIGHT MATTERS CAT. NO.Decorative suspended with wattage <20WLED BRIDGE LUX SURFACED MOUNTED DIMENSION: 600mm (dia) X 100mm (H) Lumen-1700

od271606/2021_2022 : SIMILAR TO PHILIPS SUSPENDED DECORATIVE FIXUTRE 40W DIMENSION: 600mm (dia) X 100mm (H) Lumen-3000

Sprinkler System

od157045/2021_2022 : Supply, erection, testing and commissioning of MS "C" Class pipes conforming to IS 1239 with welding joint above 65NB and socket welding joint below 50NB with including cutting pipes to correct lengths, providing fittings like elbow,tee,reducer and welding flanges to pipe, fixing with clamps to MS brackets / hangers as per drawing. Rate shall be inclusive of Zinc chromate primer over that 2 coats red enamel paint as per Fire authorities requirement over all above ground pies. Rates to inclusive of all complete as per specifications150 NB.-Heavy Class

od157046/2021_2022 : Supply, erection, testing and commissioning of MS "C" Class pipes conforming to IS 1239 with welding joint above 65NB and socket welding joint below 50NB with including cutting pipes to correct lengths, providing fittings like elbow,tee,reducer and welding flanges to pipe, fixing with clamps to MS brackets / hangers as per drawing. Rate shall be inclusive of Zinc chromate primer over that 2 coats red enamel paint as per Fire authorities requirement over all above ground pies. Rates to inclusive of all complete as per specifications<br>65 NB.-Heavy Class<br>

od157047/2021_2022 : Supply, erection, testing and commissioning of MS "C" Class pipes conforming to IS 1239 with welding joint above 65NB and socket welding joint below 50NB with including cutting pipes to correct lengths, providing fittings like elbow,tee,reducer and welding flanges to pipe, fixing with clamps to MS brackets / hangers as per drawing. Rate shall be inclusive of Zinc chromate primer over that 2 coats red enamel paint as per Fire authorities requirement over all above ground pies. Rates to inclusive of all complete as per specifications <br>100 NB. -Heavy Class<br>

od157048/2021_2022 : Supply, erection, testing and commissioning of MS "C" Class pipes conforming to IS 1239 with welding joint above 65NB and socket welding joint below 50NB with including cutting pipes to correct lengths, providing fittings like elbow,tee,reducer and welding flanges to pipe, fixing with clamps to MS brackets / hangers as per drawing. Rate shall be inclusive of Zinc chromate primer over that 2 coats red enamel paint as per Fire authorities requirement over all above ground pies. Rates to inclusive of all complete as per specifications <br>80 NB. -Heavy Class<br>

od157049/2021_2022 : Supply, erection, testing and commissioning of MS "C" Class pipes conforming to IS 1239 with welding joint above 65NB and socket welding joint below 50NB with including cutting pipes to correct lengths, providing fittings like elbow,tee,reducer and welding flanges to pipe, fixing with clamps to MS brackets / hangers as per drawing. Rate shall be inclusive of Zinc chromate primer over that 2 coats red enamel paint as per Fire authorities requirement over all above ground pies. Rates to inclusive of all complete as per specifications <br>50 NB.-Heavy Class<br>

od157050/2021_2022 : Supply, erection, testing and commissioning of MS "C" Class pipes conforming to IS 1239 with welding joint above 65NB and socket welding joint below 50NB with including cutting pipes to correct lengths, providing fittings like elbow,tee,reducer and welding flanges to pipe, fixing with clamps to MS brackets / hangers as per drawing. Rate shall be inclusive of Zinc chromate primer over that 2 coats red enamel paint as per Fire authorities requirement over all above ground pies. Rates to inclusive of all complete as per specifications<br>25 NB.-Heavy Class<br>

od157051/2021_2022 : Supply, erection, testing and commissioning of MS "C" Class pipes conforming to IS 1239 with welding joint above 65NB and socket welding joint below 50NB with including cutting pipes to correct lengths, providing fittings like elbow,tee,reducer and welding flanges to pipe, fixing with clamps to MS brackets / hangers as per drawing. Rate shall be inclusive of Zinc chromate primer over that 2 coats red enamel paint as per Fire authorities requirement over all above ground pies. Rates to inclusive of all complete as per specifications <br>32 NB.-Heavy Class<br>

od157052/2021_2022 : Supply and installation of Upright Sprinkler head with the following temperature rating & respond,chromium finish with UL &FM approved<br>Sprinkler Standard responsee K-80 and temperature rating - 68 Deg C.<br>

od157053/2021_2022 : Supply and installation of Pendant Sprinkler head with the following temperature rating & respond, chromium finish with UL &FM approved<br>Sprinkler Standard responsee K-80 and temperature rating - 68 Deg C.<br>

od157054/2021_2022 : Supply, erection, testing and commissioning of UL approved Metallic stainless steel (SS 304) Unbraided Flexible dropE pipes of 25mm dia with necessary fittings. (Flexible length shall be upto 1500mm long)<br>

od157055/2021_2022 : Supply and testing of approved type rosette plates for sprinklers at false ceiling. <br>

od157056/2021_2022 : Supplying & installing of FM approved make flow switches (flow sensors) suitable to be fixed directly on line of the following diameters, with 1 NO & 1 NC potential free contacts.<br>100 NB<br>

od157057/2021_2022 : Supply and installation of Alarm check valve with full valve trim. The alarm check valve shall be equipped with a removable cover assembly. The alarm valve shall be listed for vertical position. T shall be equipped with gauge connections on the system side and supply side of the valve clapper. The alarm valve trim piping shall be externally galvanized. Maximum water working pressure to 250 PSI. This shall be inclusive of hydraulic powered water motor alarm by way of integral valve alarm line trim piping. Water motor gong shall be connected to a water pressure retarding chamber to limit the propensity of unnecessary alarms. Water motor alarm shall be equipped with a rear closure plate to limit the access of foreign materials of accumulation of debris and as per specification<br>

od157058/2021_2022 : Supply, fabrication , erection of MS Steel works secondary pipe supports as per details given in the shop drawings<br>

od157059/2021_2022 : Supply and installation of Butterfly valve including matching flange joints ,nut, bolt, gaskets etc. All complete as per specifications -PN16<br>150 NB<br>

od157060/2021_2022 : Supply and installation of Butterfly valve including matching flange joints ,nut, bolt, gaskets etc. All complete as per specifications -PN16<br>100 NB<br>

od157061/2021_2022 : Supply, erection, testing and commissioning of GM Gate valve (DRAIN) with necessary flanges, supports, bolts, nuts, etc & (Below 50NB) screwed ends.PN16<br>50 NB<br>

od157062/2021_2022 : Supply, erection, testing and commissioning of GM Gate valve (DRAIN) with necessary flanges, supports, bolts, nuts, etc & (Below 50NB) screwed ends.PN16<br>25 NB<br>

od158976/2021_2022 : Supply & installation of Automatic Air Release Valve 25 NB CI to all wet risers all complete as per specifications.<br>

od157063/2021_2022 : Supply & installation of IS approved Pressure gauge 100mm dial (Range 0 to 16 ) Kg/cm2.<br>

od157064/2021_2022 : Supply & installation of Instrument cables for flow switches. The cable should be 2 core x 1.5 Sq.mm cable. as per specification.<br>

od157065/2021_2022 : Supply, installation, testing and commissioning of courtyard Stainless Steel Single headed hydrant as per IS: 5290 consisting of 63NB single outlet flanged oblique type hydrants valve with instantaneous female plunger type coupling, chained blank cap including making flanged joints by providing necessary nuts, bolts, gaskets all complete as per specifications suitable for 80 NB stand post.<br>

od157066/2021_2022 : Supply & installation of RRL type-A hose reel of 63mm dia. x 15 meters long with heavy quality gun metal male coupling of IS: 903. combined with 2 Nos of fire chef hoses and 1 Nos of nozzles with ms painted hose tray to accommodate hose reel<br>

od157067/2021_2022 : Supply & installation of fabricated hose box FRP of size 750x600x250 with glass(4mm thick) fronted door , painted in red out side and white in inside, hose boxes along with GI support angles for courtyard & Internal hydrants. Each box shall be capable to accommodate 2 hose each of 63 mm dia x 15 m long hose pipe, nozzle, branch pipe etc.<br>

od157068/2021_2022 : Supply, installation, testing and commissioning of 63mm dia. approved make Stainless steel single headed fire hydrant landing valves (with instantaneous female plunger type couplings, chained blank caps) including making flanged joints by providing necessary nuts, bolts, gaskets, etc. painting complete as per specifications.<br>

od157069/2021_2022 : Supply & Installation of Drum type wall mounting hose reels, swiveling 180o consisting of 19 mm dia. x 30 meters long armored rubber hose pipe with 15 mm dia. bronze shut of type jet nozzle & cut-off valve on the inlet including making connection to the wet riser, by drilling welding, fixing the hose reel to the wall by providing necessary anchor fasteners/ expansion bolts, grouting the same with cement mortar, painting all complete as per drawings, specifications.<br>

ADDRESSABLE FIRE DETECTION AND ALARM SYSTEM

od159612/2021_2022 : Addressable Fire Alarm Control panel with battery back up . The Panel Shall be Four loop capacity with battery charger and inbuilt with network card etc, The panel shall consisting with 80 character LCD display and RS 485 for networking. <br>

od159613/2021_2022 : Supplying, installing, testing and commissioning of photo electric (optical) smoke detector with base, junction box and other accessories (Above false ceiling ) <br>

od159614/2021_2022 : Supplying, installing, testing and commissioning of photo electric (optical) smoke detector with base, junction box and other accessories (Below false ceiling ) <br>

od159615/2021_2022 : Addressable rate of rise Heat detector with base, Junction box and other accessories as required.<br>

od159616/2021_2022 : Response indicator for all detectors located above false ceiling / false floor<br>

od159617/2021_2022 : Analogue Addressable Fault isolator module capable of monitoring shorted loop circuit and automatically restore communications when shorted conditions are corrected<br>

od159618/2021_2022 : Supplying, installing, testing and commissioning of Analogue Addressable relay control Module for Smoke exhaust, Lift Machine Room & for tripping AHU and open/close supply & return air into conditioned area, motorized fire damper & deactivation of access control doors.<br>

od159619/2021_2022 : Analogue Addressable single Input Module for integrating conventional Sprinkler Flow Switch, pump run & ON status of fire pumps and other conventional devices with fire alarm control panel.<br>

od159620/2021_2022 : Supplying, installing, testing and commissioning of Analogue Addressable Sounder cum strobe<br>

od159621/2021_2022 : Supplying, installing, testing and commissioning of Addressable Manual Call Point with back box. Back box will be flushed on wall.<br>

od159622/2021_2022 : Supplying and laying of 2 core x 1.5 mm², Armoured, FRLS, PVC insulated copper conductor cable confirming to relevant IS standards . Red colour <br>

od159623/2021_2022 : Supplying, installing, testing and commissioning of power supply unit which provides 24V DC output for connecting all relay control modules and other modules. one number of 7AH battery with all accessories and multiple terminal connections. The power supply unit will be located near to FA/PA shaft in typical floors.<br>

P.A. SYSTEM

od162041/2021_2022 : Supplying, installing, testing and commissioning solid state Amplifier of 500 W RMS out put in rack, including necessory control wires, jacks etc. complete<br>

od162042/2021_2022 : Supplying, installing, testing and commissioning of 15W RMS, 110V, wall mounted Box type speaker inbuilt with Volume controller will be concealed with Weather proof enclosure complete with all mounting accessories.<br>

od162043/2021_2022 : Supplying, installing, testing and commissioning of 6W RMS, 110V, 106dB sound level wall mounted horn speaker with all mounting accessories. <br>

od162044/2021_2022 : Supplying, installing, testing and commissioning of 6W RMS, 110V, 106dB sound level Ceiling speaker with all mounting accessories. <br>

od162045/2021_2022 : Supplying and laying of 2Cx1.5 mm², Armoured, FRLS, PVC insulated annealed tinned copper conductor cable confirming to relevant IS standards . yellow colour <br>

od162046/2021_2022 : Providing and Fixing of Gooseneck Microphone with call station. Features : Dynamic Directivity: Cardioid Frequency response : 100Hz÷12 kHz Sensitivity: (OdB-1V/micro bar,1000 Hz) -75dB±3dB Output impedance :500ohm<br>

od162047/2021_2022 : Providing & Fixing of duly wired Equipment Rack to accommodate all above mentioned control equipment like console, amplifier, DVD player etc.

Godrej and Boyce Manufacturing Company Limited

Macro Enterprises

Cauvery Buildtech

THE URALUNGAL LABOUR CONTRACT CO-OPERATIVE SOCIETY

Bidder Name

THE URALUNGAL LABOUR CONTRACT CO-OPERATIVE SOCIETY

Macro Enterprises

Keechery Engg Co

Godrej and Boyce Manufacturing Company Limited

Cauvery Buildtech