E-Procurement Notice No.39/OCCL/2023-24 (on-line)

Amount

RADIAL GATES OF INDRAVATI DAM (BAY NO. 4,5)

Dismantling, removal and shifting of existing radial gates in bay No. 4 & 5 with its components to desiginated site provide by Deptt. by cutting into pieces including labour, hire charge of machinery, crane, equipments, tools & tackles etc, excluding Oxygen, DA to be supplied by Corporation and as per direction of Engineer-in-charge

Dismantling and removal of existing hoist bridge in bay No. 4 & 5 including hoisting arrangements, wire rope assemblies etcincluding labour, hire charge of machinery, crane, equipments, tools & tackles etc, excluding Oxygen, DA to be supplied by Corporation and as per direction of Engineer-in-charge.

Erection, Fabrication, commissioning, testing of new radial gates in bay No. 4 & 5 with its components in segmentation method including labour, hire charge of machinery, crane, equipments, tools & tackles etc, excluding welding rod, Oxygen, DA to be supplied by Corporation and as per direction of Engineer-in-charge

Dismantling of existing trunnion hub assemblies and re-erection of the same after rectification, alignment, overhauling including labour, hire charge of machinery, crane, equipments, tools & tackles etc. and direction of Engineer-in-charge

Re-erection of dismantled hoist bridge & hoisting arrangements in bay No. 4 & 5 with alignment, Fabrication, commissioning and testing, fitting of new wire rope assemblies, overhauling of hoisting arrangemnts, application of cardium compound in wire ropes, gear oil topping in worm reducerincluding labour, hire charge of machinery, crane, equipments, tools & tackles etc, excluding wire ropes, turn buckles, Grease, Cardium compound, gear oil, welding rod, Oxygen, DA to be supplied by Corporation and as per direction of Engineer-in-charge.

Painting of 2 (Two) sets new radial gate and its components in bay No.4 & 5 after surface preparation by blast cleaning process, performed with sand as per requirements and class 'A' of IS : 14177:1994. After blast cleaning, the surface should be cleaned from loose dust and debris preferably by air blast with help of blower. Over the prepared surfaces two coats of zinc rich primer should be applied to give a total dry film thickness of 70 ± 5 microns followed by two coats of solvent less coal tar epoxy paint applied at an interval of 24 hours. Each coat should give a minimum dry film thickness of 150±5 microns. The total dry film thickness of all the coats including primer coating should not less than 350 ±5 microns as per IS: 14177:1994, including sand, labour, machinery, equipments, scaffolding etc.and as per direction of Engineer-in-charge

Arrest of leakage through stoplog segments (09 segments) in front of Radial gates in Bay No.4 & 5 to facilitate replacement of existing damaged gates & insertion of new Gates including supply of equipments, under water drivers with required license, cotton waste, gunny bags, rope & transportation charges of vehicle, manpower, taxes etc.of UIHEP, Dist-Nawarangpur (Odisha) complete in all respect & as per direction of Engineer-in-charge

Insertion of Stoplog segments (09 segments) in up-stream side of Radial gates by operating Gantry crane to stop water flow including labour, equipments etc. & as per direction of Engineer-in-charge

RADIAL GATES OF MURAN DAM (BAY NO. 4)

Dismantling, removal and shifting of existing radial gates in bay No. 4 with its components to desiginated site provide by Deptt. by cutting into pieces including labour, hire charge of machinery, crane, equipments, tools & tackles etc, excluding Oxygen, DA to be supplied by Corporation and as per direction of Engineer-in-charge.

Dismantling and removal of existing hoist bridge in bay No. 4 including hoisting arrangements, wire rope assemblies etc.including labour, hire charge of machinery, crane, equipments, tools & tackles etc, excluding Oxygen, DA to be supplied by Corporation and as per direction of Engineer-in-charge

Erection, Fabrication, commissioning, testing of new radial gates in bay No. 4 with its components in segmentation methodincluding labour, hire charge of machinery, crane, equipments, tools & tackles etc, excluding welding rod, Oxygen, DA to be supplied by Corporation and as per direction of Engineer-in-charge

Dismantling of existing trunnion hub assemblies and re-erection of the same after rectification alignment, overhauling including labour, hire charge of machinery, crane, equipments, tools & tackles etc. and as per direction of Engineer-in-charge

Re-erection of dismantled hoist bridge & hoisting arrangements in bay No. 4 with alignment, Fabrication, commissioning and testing, fitting of new wire rope assemblies, overhauling of hoisting arrangemnts, application of cardium compound in wire ropes, gear oil topping in worm reducer etc. including labour, hire charge of machinery, crane, equipments, tools & tackles etc, excluding wire ropes, turn buckles, Grease, Cardium compound, gear oil, welding rod, Oxygen, DA to be supplied by Corporation and as per direction of Engineer-in-charge

Painting of 2 (Two) sets new radial gate and its components in bay No.4 after surface preparation by blast cleaning process, performed with sand as per requirements and class 'A' of IS : 14177:1994. After blast cleaning, the surface should be cleaned from loose dust and debris preferably by air blast with help of blower. Over the prepared surfaces two coats of zinc rich primer should be applied to give a total dry film thickness of 70 ± 5 microns followed by two coats of solvent less coal tar epoxy paint applied at an interval of 24 hours. Each coat should give a minimum dry film thickness of 150±5 microns. The total dry film thickness of all the coats including primer coating should not less than 350 ±5 microns as per IS: 14177:1994, including sand, labour, machinery, equipments, scaffolding etc.and as per direction of Engineer-in-charge

Arrest of leakage through stoplog segments (09 segments) in front of Radial gates in Bay No.4 to facilitate replacement of existing damaged gates & insertion of new Gates including supply of equipments, under water drivers with required license, cotton waste, gunny bags, rope & transportation charges of vehicle, manpower, taxes etc.of UIHEP, Dist-Nawarangpur (Odisha) complete in all respect & as per direction of Engineer-in-charge

Insertion of Stoplog segments (09 segments) in up-stream side of Radial gates by operating Gantry crane to stop water flow including labour, equipments etc. & as per direction of Engineer-in-charge

KAMAKSHI ENGINEERING WORKS

ANANTA CONSTRUCTIONS